Solar Tracking Ppt
Transcript of Solar Tracking Ppt
-
7/31/2019 Solar Tracking Ppt
1/18
Solar Tracking System using
Real Time Clock
By
H.Mahesh Kumar (06-09-4081)
N.Mahesh (06-09-4082)
B.Mukesh (06-09-4088)
-
7/31/2019 Solar Tracking Ppt
2/18
Aim of the Project The main objective of this project is to track the sun and
rotate the solar panel accordingly, to receive sunlight to thefullest extent always during the day time
This movement is achieved by interfacing a stepper motor tothe solar panel that changes its direction according to thepositioning of the sun.
This is achieved using time reference that controls themovement time for 12 hours by a program written in such away that for every given time the solar panel faces to the sunto generate maximum power
-
7/31/2019 Solar Tracking Ppt
3/18
Introduction
We are using microcontroller 89S52 for controlling the
panel so that panel is rotated according to the sunsposition
A Stepper motor is used and it control and rotation is
done by the microcontroller
We also use KEIL software to simulate the programwhich is written in embedded C
-
7/31/2019 Solar Tracking Ppt
4/18
Block diagram of projectMICRO CONTROLLER
POWER
SUPPLY
RTC
LCD
Motor
driver
Stepper
Motor
-
7/31/2019 Solar Tracking Ppt
5/18
Why AT 89s52?
Coming to the question of why to use AT89s52 of allthe 8-bit Microcontroller available in the market themain answer would be because it has 8 Kb on chipflash memory which is just sufficient for ourapplication. The on-chip Flash ROM allows theprogram memory to be reprogrammed in system or byconventional non-volatile memory Programmer.Moreover ATMEL is the leader in
Flash technology in todays market place and henceusing AT 89s52 is the optimal solution.
-
7/31/2019 Solar Tracking Ppt
6/18
Software used KEIL
Vision3 is an IDE (Integrated DevelopmentEnvironment) that helps you write, compile, anddebug embedded programs.
Embedded C is used in this project
-
7/31/2019 Solar Tracking Ppt
7/18
Power supply
-
7/31/2019 Solar Tracking Ppt
8/18
Description of power supply The circuit uses standard power supply comprising of a step-
down transformer from 230v to 12v and 4 diodes forming a
Bridge Rectifier that delivers pulsating dc which is then filtered
by an electrolytic capacitor of about 470microf to 100microF.
The filtered dc being un regulated IC LM7805 is used to get 5v
constant at its pin no 3 irrespective of input dc varying from 9v
to 14v
The regulated 5volts dc is further filtered by a small capacitor
of 10 micro f for any noise so generated by the circuit
-
7/31/2019 Solar Tracking Ppt
9/18
Microcontroller AT89S52 Compatible with MCS-51 Products
8K Bytes of In-System Programmable (ISP) Flash
Memory 256 x 8-bit Internal RAM
Three 16-bit Timer/Counters
-
7/31/2019 Solar Tracking Ppt
10/18
Real Time Clock The RTC chip is a specialized chip that just keeps track of
time.
It runs on a battery and keeps time for you even when there is a
power outage.
Using an RTC, you can keep track of long timelines, even if
you reprogram your microcontroller or disconnect it from USB
or a power plug.
The RTC we'll be using is the DS1307 . It's low cost, easy to
solder, and can run for years on a very small coin cell.
-
7/31/2019 Solar Tracking Ppt
11/18
Motor Driver ULN2003 ULN2003 is a relay driver
It is used to drive the Stepper motor
It gives a low output to Stepper motor coil whichdrives the gear of stepper motor
It functions as inverter and it is cost effective
-
7/31/2019 Solar Tracking Ppt
12/18
Stepper Motor A stepper motor (or step motor) is a brushless synchronous
electric motor that can divide a full rotation into a large number
of steps.
To make the motor shaft turn, first one electromagnet is given
power, which makes the gear's teeth magnetically attracted to
the electromagnet's teeth.
So when the next electromagnet is turned on and the first is
turned off, the gear rotates slightly to align with the next one,
and from there the process is repeated
-
7/31/2019 Solar Tracking Ppt
13/18
LCD Display The LCD panel is used in interfacing with micro-
controller to display the Time and Solar Tracker
This is a 16 character x 2 lines LCD module capable ofdisplaying numbers and characters
-
7/31/2019 Solar Tracking Ppt
14/18
Schematic Diagram
-
7/31/2019 Solar Tracking Ppt
15/18
Procedure: Survey
First we studied about all components like
microcontroller,lcd,steppermotor
And we decided to modify project such that we areusing RTC DS1307 instead of LDRs
-
7/31/2019 Solar Tracking Ppt
16/18
Procedure
We bought all the components needed for our project
We soldered all components according to theschematic
We wrote the code and created hex file in keil software
We dumped hex file with the help of
willarprogrammer to the micro controller
-
7/31/2019 Solar Tracking Ppt
17/18
Software Programming KEIL
Vision3 is an IDE (Integrated DevelopmentEnvironment) that helps you write, compile, anddebug embedded programs.
Embedded C is used in this project
-
7/31/2019 Solar Tracking Ppt
18/18