Solar Cell Sederhana Ala Mac Gyver
-
Upload
mochamad-raidz-khairi -
Category
Documents
-
view
223 -
download
1
Transcript of Solar Cell Sederhana Ala Mac Gyver
Simple Solar Cell ala Mac Gyver
Powdered sugar contains nano particles of titanium dioxide, a substance which is also used in
paints. When the powder was sugar coated with organic dyes such as passionfruit tea then it
functions as a light absorber layer of solar photovoltaic devices.
In the solar cell system with dyeing, colored organic material such as tea can absorb some of you
seen the light and converts the energy into electron carrier material such as white TiO2, who can not
absorb their own.
Once the electron has been raised, they need to go somewhere. Identical with the sandwich, the
TiO2 is between clean electrodes and electrodes made from graphite-made by rubbing pencil on the
glass. As a final touch add a few who gained from the electrolyte solution iodine solution that is
usually used for water purification.
Sensitive solar cell of the system, this immersion can be cheaper and more durable than traditional
photovoltaic, but the efficiency is lower.
How to make a simple solar cell is as follows:
* Method I
Step one is to use a donut sprinkled with powdered sugar and passionfruit white tea:
1. Pour out powdered sugar donuts and who clung to collect
2. TSB powder Mix with hot water, stirring constantly
3. Strain the solution of TSB with fine filters can be found who, paper coffee filters can also be used.
4. Fabrics TiO2 is insoluble in water.
5th. What we need is long-TiO2 and polymer chain
6. Enter the residue / precipitate that remains solid on the filter paper into the hot oven (500 degrees
Celsius)
7. Remove the TiO2 powder and add alcohol
8. Pour the white layer of TiO2 on glass berpenghantar solution. This glass had previously been
coated with a transparent layer of barium penghantar (SnO2), as well as TiO2 films.
9. Allow to dry and do it until 10 layers.
10. What we need next is a natural fruit juice such as: raspberry, blackberry, pomegranate seed / red
pomegranate, black currant, leaves Canada, Tea Hibiscus Tea Passion red or custom-made from
hibiscus plants containing anthrocyanin. Chains made of organic carbon and hydrogen. Or is best to
use the Starbucks Passion Tea.
11. Nano TiO2 particles are needed to be made sensitive by using Starbucks Passion Tea.
12. Or if not, lumatkan TSB one of the organic material on top and mix with a spoonful of water.
13. Soak for 5 minutes TSB film in this solution to obtain the former cliff-red stain-purple. When both
sides of the film does not imprint evenly, then return to soak in a solution of TSB juice for more than
five minutes.
14. When using Starbucks Passion Tea soak for several hours so that the TiO2 film changed color
from white to purple
15. The dark means to absorb light.
16. Wash the film with ethanol and gently dried with use of tissues.
17. Photoelectrochemical solar cell installation
18. Put a pencil on film, the clean up is grayed out.
19. Provide iodine tablets for water purification and alcohol
20. Cut the usual film-shaped frame (you can of Scotch who isolation nodes) are center part holes
and fit the size of the hole surface of TiO2 films that have been colored purple. Squirt liquid derived
from the solution of iodine is usually used for water purification on the surface of TiO2.
21. Then cover with a layer of regular movie on it (like a sandwich) and clamp the ends with paper
clips.
22. Measure both ends with a micro-amperes it will show the existence of a small electrical current
that changes who follow the presence or absence of light sources.
Step two:
1. Put layer Titanium Dioxide (TiO2) with natural dyes obtained from fruit juice, blackberries,
raspberries, pomegranate seeds
red, red Hibiscus Tea, Starbucks Passionfruit Tea, etc..
2. Counter electrode coating:
Solar cells require positive and negative plates to serve. Called the positive electrode and counter
electrode are assembled from a glass plate coated with SnO2 penghantar materials. Ohmmeter can
be used to check where the conductive part, the sign is carved with a fingernail when this is the
rough side. Non-conductive side marked with +. Use the tip of a pencil to scratch and create a thin
layer of graphite (catalytic carbon) on the surface of the conductive plate.
3. Add electrolytes and assemble the final stages of solar cell
Serves as an electrolyte solution of iodine in the solar cell which is to complement the circuit and
regenerates the coating. Place a plate that had been smeared on the table so that the film side at
the top and drops one or two drops of iodine electrolyte to the dirty part of the film. Then place the
counter electrode on the top of a dirty movie, so the conductive side of the counter electrode is at the
top of the film. Dragged the glass plate so that the edge of the plate is visible. This will be the contact
point for the positive and negative electrodes so that we can measure the solar cell and tried to
TSB.
4. Use two clamps to hold the two electrodes together at the ends of the plate. The output voltage
around 0.43 V and 1 mA/cm2 when the cell full of sunshine through the TiO2.
* Method II
By leveraging the power transistors (transistors jengkol) NPN type such as 2N3055. From the first
transistor can generate voltage jengkol 0.5 to 0.6 VDC.
Open the casing cover jengkol transistors by sawing a prominent part (writing imaginable type and
no code), then point the parts that have been open to the sun and measuring the voltage with a
voltmeter to the position as shown below. The base is a negative pole and the feet with foot emitter
dijumper colector who represents the positive pole. Currents produced are very small, but by
connecting the three transistors in series will be obtained jengkol voltage to 1.8 V and can charge
one battery type AAA/UM4.
* Method III
By using cuprous oxide instead of silicon. Oxida cuprous or copper oxide is one of the first material
that can produce the photoelectric effect is the effect of light caused an electric current flowing in the
material.
The materials used are as follows:
1. A sheet of thin copper plate with a size of approximately 15cm x 30cm
2. Two crocodile clips
3. Micro amperemeter sensitive who can read between 10 and 50 micro amperes.
4. Electric stove with a large power 1100 Watt
5th. Large plastic bottle or can also use two-liter bottle of mineral water which cut top. Glasses with a
big mouth can also be used.
6. Table salt, it takes a few tablespoons of salt.
7. Water faucets
8. Sandpaper or wire brush
9. Scissors to cut thin sheets of copper
How to make are as follows:
1. Cut the copper plate to the size of the heating stove electric stove. Wash hands to remove the fat
stains on his hands. Then wash the copper sheet TSB with soap to remove stains of oil or fat on its
surface. Use sandpaper or wire brush to clean the surface completely flat so that the copper
sulphide stains or corrosion can be lifted slightly.
2. Place a piece of copper that has been cleaned and dried in the oven heater and electric stove set
of figures who in the highest.
3. At the time of the copper plate was hot, who will look beautiful oxidation patterns begin to
form.Orange, purple and red began to cover the copper surface.
4. At the time of the copper plate from the heat, its color will change to blackish which is a layer of
cupric oxide or copper oxide. But this is not the oxide we want, show the colors red, orange, pink
and purple from copper oxide under layer.
5th. Next TSB color pattern will disappear along with heaters who began glowing red
6. When heating began glowing red, copper plates will be coated with black copper oxide. Allow
heated for half an hour so that her black coating will be thicker. This is important in a thick layer will
flake easily, while a thin layer of copper will remain stuck on.
7. After half hour warm-up, turn off the stove. Leave the hot copper plates on the stove cools
slowly. If cooling too quickly, the black oxide will stay stuck to the copper.
8. At the copper cools, it will shrink. Black copper oxide also shrinks, but shrinkage in different
ranges, making peeling black copper oxide.
9. The small Black peeling out of the copper with enough force to make those who fly a few
inches. This means less cleaning effort around the stove, but it was fun to watch.
10. When the copper has cooled in accordance with room temperature (takes approximately 20
minutes), most of the black oxide will be lost. Rub gently with hands under running water would lift
most small bits. Do not pick up all the black spots by hard scrubbing or bend this thin copper
plate. This may damage the soft layer of red copper oxide that we need to make solar cells work.
11. The next installation is very simple and quick. Cut another piece of copper the same size as the
first who. Bend both ends slowly, so it can fit into a plastic bottle without touching one
another.Copper oxide layer who is facing upwards on the stove is usually a best side to face outward
in the bottle because it is the finest and cleanest surface.
12. Connect the two alligator clips, one for the new copper plate and the other who to plate the
copper oxides. Connect one end of the clean copper plate with the positive terminal of the
meter.Connect one end of the copper oxide plate with the negative terminal of the meter.
13. Now mix a couple tablespoons of table salt into hot water. Stir in salt water until the salts
dissolve. Then carefully pour the brine into the jar, being careful not to wet the tip of crocodile
jaws. Salt water does not have to cover the plate, leave approximately 1 inch tall salt water from the
surface plate so that we can move out TSB solar cell around without getting wet crocodile jaws.
Notice in the picture above that the meter reads the flow of electricity at 6 micro-amperes. This is
a solar cell battery, although in the dark and usually shows few micro-amperes of electric current.
While the test showed the picture above the solar cell in a state of the sun. Notice that the meter has
shown an electric current of about 33 micro amperes. Even sometimes the needle can indicate up to
50 micro-amperes, which makes the needle move fully to the right.
This solar cell can produce 50 micro-amperes with a voltage of 0.25 V, this means that can produce
power equal to 12.5 micro watts.
12.5 mikrowatt is to cell size of 0.01 m2 or 1.25 milliwatt per m2.
Independent Power Solar Cell
Generating electricity at home? It was made possible by the installation of solar cells, solar cells
convert sunlight into electricity. Electricity is stored in
batteries,battery switch on the lights.
In the use of solar cell to generate electricity at home, there are some things we need to consider
because the characteristics of the solar cell:
* Solar cell requires sunlight. Place the solar cell at the position where not obstructed by objects
throughout the morning until the afternoon.
* Solar Cell - solar cell produces direct current electricity, DC.
* For higher efficiency, use DC lamps such as LED lights.
* Installing a new cable for direct current, DC for the following devices such as: LED-based lighting
(Light Emiting Diode), CCTV cameras, wifi (wireless fideliity), etc..
When we make a new home, it is advisable to use electricity
and solar cell. Solar cell is used for partial illumination (in this case using direct current DC) and
electricity to alternating current devices such as air conditioning: Air conditioning, Refrigerator, some
lighting etc.
When the DC power stored in batteries to use the device turn on the AC: water pumps, refrigerators,
etc. it is necessary that the inverter can convert DC power into AC.Customize your power needs
required by solar cell,inverters, batteries.
LED lamps as lighting Houses
There is now using energy efficient lighting such as LED lighting, DC. Compare 3 Watt LED light the
equivalent of 15 Watt AC Lighting.
The drawback is:
* Installing a new cable for the LED light.
* The cost of procurement of more expensive lights.
The advantage is:
* The use of small energy
* The reliability of the LED light 10 x usual standard lamp
* Use two core electrical cable.
AC Lamp LED LampVoltage 220 VAC 12 VDCWatt 15 Watt 3 WattLifetime 6,000 hours 50,000 hoursCost + Rp. 25,000 + Rp. 250,000Solar Cell for AC Electric
If we wish to use the energy of solar cells for other home equipment, follow the example of the
following calculation.
If we take the alternating current electric power at 2000W for 10 hours per day (20KWh/hari) then
the required 24 panels of solar cells with the capacity of each 210WP and 30 @ 12V 100Ah
battery. This is based on the calculation of solar energy from 7 am until 5 pm (10 hours) and the
assumption of energy conversion at least 4 hours a day
.
Solar energyThe amount of solar cell
Capacity of solar cell
Calculation Result
4 hours 24 panel 210 Watt 4 x 24 x 21020.160 Watt hour
Basis for calculating the number of batteries are 2 x 3 x electrical needs.
The existence of the multiplier 3 to anticipate when the rain / overcast continuously for three
consecutive days. While the multiplication factor 2 due to battery must be no more than 50% loss of
capacity if it wants long-lasting battery, especially for such a dry battery type gel and AGM. In other
words labored to DOD (Depth of Discharge) did not exceed 50% because it is affecting life time of
the battery itself.
The amount of batteryVoltage Ampere Calculation Result
100 12 Volt 100 Ampere hour 100 x 12 x 100120.000 Watt hour
Solar Cell Sederhana ala Mac GyverGula bubuk mengandung partikel nano dari titanium dioksida, zat yang juga digunakan dalam cat. Ketika bubuk gula itu dilapisi dengan pewarna organik seperti teh markisa maka berfungsi sebagai lapisan penyerap cahaya perangkat fotovoltaik surya.
Dalam sistem sel surya dengan pencelupan, bahan organik berwarna seperti teh dapat menyerap beberapa dari Anda melihat cahaya dan mengubah energi menjadi bahan pembawa elektron seperti putih TiO2, yang tidak bisa menyerap mereka sendiri.
Setelah elektron telah dibangkitkan, mereka perlu pergi ke suatu tempat. Identik dengan sandwich, TiO2 adalah antara elektroda yang bersih dan elektroda yang terbuat dari grafit buatan dengan mengoleskan pensil pada kaca. Sebagai sentuhan akhir tambahkan sedikit yang diperoleh dari larutan yodium larutan elektrolit yang biasanya digunakan untuk pemurnian air.
Sel surya sensitif dari sistem, perendaman ini bisa lebih murah dan lebih tahan lama dibandingkan photovoltaic tradisional, tetapi efisiensi yang lebih rendah.
Cara membuat sel surya sederhana adalah sebagai berikut:
* Metode I
Langkah pertama adalah dengan menggunakan donat ditaburi dengan gula bubuk dan markisa teh putih:
1. Tuangkan bubuk gula donat dan yang menempel untuk mengumpulkan2. TSB bubuk Campur dengan air panas, aduk terus3. Saring larutan tsb dengan filter halus yang dapat ditemukan, kertas filter kopi juga dapat digunakan.4. Kain TiO2 tidak larut dalam air.5. Yang kita butuhkan adalah panjang TiO2 dan rantai polimer6. Masukkan sisa / endapan yang tetap solid pada kertas saring ke dalam oven panas (500 derajat Celsius)7. Lepaskan bubuk TiO2 dan menambahkan alkohol8. Tuangkan lapisan putih TiO2 pada solusi berpenghantar kaca. Kaca ini sebelumnya telah dilapisi dengan lapisan transparan dari barium penghantar (SnO2), serta film TiO2.9. Biarkan mengering dan lakukan sampai 10 lapis.10. Apa yang kita butuhkan selanjutnya adalah jus buah alami seperti: raspberry, blackberry, delima benih / merah delima, kismis hitam, daun Kanada, teh Hibiscus Tea Gairah merah atau custom-made dari tanaman kembang sepatu yang mengandung anthrocyanin. Rantai yang terbuat dari karbon organik dan hidrogen. Atau yang terbaik adalah menggunakan Teh Gairah Starbucks.11. Nano partikel TiO2 ini perlu dibuat sensitif dengan menggunakan Teh Gairah Starbucks.12. Atau jika tidak, lumatkan tsb salah satu bahan organik di atas dan campur dengan sesendok air.13. Rendam film tsb 5 menit dalam larutan ini untuk mendapatkan tebing merah bekas noda ungu. Ketika kedua sisi film tersebut tidak membekas secara merata, kemudian kembali ke rendam dalam larutan jus tsb selama lebih dari lima menit.14. Bila menggunakan teh Gairah Starbucks rendam selama beberapa jam sehingga film TiO2 berubah warna dari putih ke ungu15. Gelap berarti menyerap cahaya.16. Cuci film dengan etanol dan dengan lembut dikeringkan dengan penggunaan jaringan.17. Fotoelektrokimia sel surya instalasi
18. Masukan pensil pada film, pembersihan berwarna abu-abu.19. Memberikan tablet yodium untuk pemurnian air dan alkohol20. Potong frame film berbentuk biasa (Anda dapat Scotch yang node isolasi) adalah pusat lubang bagian dan sesuai dengan ukuran permukaan lubang film TiO2 yang telah berwarna ungu. Teteskan cairan yang berasal dari larutan yodium biasanya digunakan untuk pemurnian air pada permukaan TiO2.21. Kemudian tutup dengan lapisan film biasa di atasnya (seperti sandwich) dan klem ujung dengan klip kertas.22. Ukur kedua ujungnya dengan mikro ampere maka akan terlihat adanya arus listrik kecil yang perubahan yang mengikuti ada tidaknya sumber cahaya.
Langkah kedua:
1. Masukan lapisan Titanium Dioksida (TiO2) dengan pewarna alami yang diperoleh dari jus buah, blackberry, raspberry, biji delima
merah, merah Hibiscus Tea, Starbucks markisa teh, dll.
2. Kontra elektroda lapisan:
Sel surya memerlukan pelat positif dan negatif untuk melayani. Disebut elektroda positif dan elektroda counter dirakit dari piring kaca dilapisi dengan bahan penghantar SnO2.Ohmmeter dapat digunakan untuk memeriksa di mana bagian konduktif, tanda diukir dengan kuku saat ini adalah sisi kasar. Non-konduktif sisi bertanda +. Gunakan ujung pensil untuk menggores dan membuat lapisan tipis dari grafit (karbon katalitik) pada permukaan plat konduktif.
3. Tambahkan elektrolit dan merakit tahap akhir sel surya
Berfungsi sebagai larutan elektrolit yodium dalam sel surya yang adalah untuk melengkapi sirkuit dan meregenerasi lapisan. Tempatkan plat yang telah dioleskan pada meja sehingga sisi film di bagian atas dan turun satu atau dua tetes elektrolit yodium pada bagian yang kotor dari film. Kemudian tempat elektroda counter pada bagian atas sebuah film kotor, sehingga sisi konduktif dari elektroda counter di bagian atas film tersebut. Menyeret pelat kaca sehingga tepi piring terlihat. Ini akan menjadi titik kontak untuk elektroda positif dan negatif sehingga kita dapat mengukur sel surya dan mencoba tsb.
4. Gunakan dua penjepit untuk memegang dua elektroda bersama-sama di ujung piring.Tegangan keluaran sekitar 0,43 V dan 1 mA/cm2 ketika sel penuh sinar matahari melalui TiO2 tersebut.
* Metode II
Dengan memanfaatkan transistor daya (transistor jengkol) NPN tipe seperti 2N3055.Dari transistor pertama dapat menghasilkan tegangan jengkol 0,5-0,6 VDC.
Buka penutup casing transistor jengkol dengan menggergaji bagian yang menonjol (menulis jenis dibayangkan dan tidak ada kode), lalu arahkan bagian yang telah terbuka ke matahari dan mengukur tegangan dengan voltmeter dengan posisi seperti gambar di bawah. Dasar adalah kutub negatif dan kaki dengan colector dijumper emitor kaki yang mewakili kutub positif. Arus yang dihasilkan sangat kecil, tetapi dengan menghubungkan tiga transistor dalam seri akan diperoleh tegangan jengkol menjadi 1,8 V dan dapat mengisi satu jenis baterai AAA/UM4.
* Metoda III
Dengan menggunakan oksida tembaga bukan silikon. Oxida tembaga atau tembaga oksida merupakan salah satu material pertama yang dapat menghasilkan efek fotolistrik adalah efek cahaya yang disebabkan arus listrik yang mengalir dalam materi.
Bahan yang digunakan adalah sebagai berikut:
1. Selembar pelat tembaga tipis dengan ukuran sekitar 15cm x 30cm2. Dua buaya klip3. Micro amperemeter sensitif yang dapat membaca antara 10 dan 50 ampere mikro.4. Kompor listrik dengan daya 1100 Watt besar5. Plastik botol besar atau juga dapat menggunakan dua liter botol air mineral yang dipotong atas. Kacamata dengan mulut besar juga dapat digunakan.6. Garam meja, dibutuhkan beberapa sendok makan garam.7. Air kran8. Amplas atau sikat kawat9. Gunting untuk memotong lembaran tipis tembaga
Cara membuatnya adalah sebagai berikut:
1. Potong plat tembaga dengan ukuran kompor kompor pemanas listrik. Cuci tangan untuk menghilangkan noda-noda lemak pada tangannya. Kemudian mencuci lembaran tembaga tsb dengan sabun untuk menghilangkan noda minyak atau lemak pada permukaannya. Gunakan amplas atau sikat kawat untuk membersihkan permukaan benar-benar datar sehingga noda sulfida tembaga atau korosi dapat diangkat sedikit.2. Tempatkan lempengan tembaga yang telah dibersihkan dan dikeringkan dalam oven pemanas dan set kompor listrik dari tokoh-tokoh yang di tertinggi.
3. Pada saat lempeng tembaga panas, yang akan terlihat pola oksidasi indah mulai terbentuk. Oranye, ungu dan merah mulai menutupi permukaan tembaga.
4. Pada saat pelat tembaga dari panas, warnanya akan berubah menjadi kehitaman yang merupakan lapisan oksida atau tembaga oksida tembaga. Tapi ini bukan oksida yang kita inginkan, menunjukkan warna merah, oranye, pink dan ungu dari oksida tembaga di bawah lapisan.
5. Selanjutnya pola warna tsb akan menghilang bersama dengan pemanas yang mulai merah menyala
6. Ketika pemanasan mulai merah menyala, pelat tembaga akan dilapisi dengan oksida tembaga hitam. Biarkan dipanaskan selama setengah jam sehingga lapisan hitam akan lebih tebal. Hal ini penting dalam lapisan tebal akan mengelupas dengan mudah, sementara lapisan tipis tembaga akan tetap terjebak di.
7. Setelah setengah jam pemanasan, matikan kompor. Biarkan pelat tembaga panas di atas kompor mendingin perlahan. Jika pendinginan terlalu cepat, oksida hitam akan tetap menempel tembaga.
8. Pada tembaga mendingin, maka akan menyusut. Oksida tembaga hitam juga menyusut, tapi penyusutan pada rentang yang berbeda, membuat mengupas oksida tembaga hitam.
9. The Black kecil mengupas keluar dari tembaga dengan kekuatan yang cukup untuk membuat mereka yang terbang beberapa inci. Ini berarti sedikit usaha pembersihan di sekitar kompor, tetapi itu menyenangkan untuk menonton.
10. Ketika tembaga telah didinginkan sesuai dengan suhu kamar (berlangsung sekitar 20 menit), sebagian besar oksida hitam akan hilang. Gosokkan secara lembut dengan tangan di bawah air mengalir akan mengangkat bit yang paling kecil. Jangan mengangkat semua bintik hitam dengan keras menggosok atau menekuk pelat tembaga tipis. Ini dapat merusak lapisan lembut oksida tembaga merah yang kita butuhkan untuk membuat sel surya bekerja.
11. Instalasi berikutnya adalah sangat sederhana dan cepat. Potong sepotong tembaga ukuran yang sama dengan yang pertama. Tekuk kedua ujungnya perlahan-lahan, agar masuk ke dalam botol plastik tanpa menyentuh satu sama lain. Tembaga oksida lapisan yang menghadap ke atas di atas kompor biasanya merupakan sisi terbaik untuk menghadapi keluar di dalam botol karena itu adalah permukaan terbaik dan terbersih.
12. Hubungkan klip buaya dua, satu untuk pelat tembaga baru dan lain yang ke piring oksida tembaga. Hubungkan salah satu ujung dari pelat tembaga bersih dengan terminal positif dari meter. Hubungkan salah satu ujung dari pelat tembaga oksida dengan terminal negatif dari meteran.
13. Sekarang mencampur dua sendok makan garam meja ke dalam air panas. Aduk air garam sampai garam larut. Kemudian hati-hati tuangkan air garam ke dalam botol, hati-hati untuk tidak membasahi ujung rahang buaya. Air garam tidak harus menutupi piring, biarkan sekitar 1 inci air garam tinggi dari pelat permukaan sehingga kita bisa bergerak keluar sel surya di seluruh tsb tanpa rahang buaya basah.
Perhatikan pada gambar di atas bahwa meter membaca aliran listrik sebesar 6 mikro ampere. Ini adalah baterai sel surya, meskipun dalam gelap dan biasanya menunjukkan beberapa mikro ampere arus listrik.
Sedangkan uji menunjukkan gambar di atas sel surya dalam keadaan matahari.Perhatikan bahwa meter telah menunjukkan arus listrik dari sekitar 33 ampere mikro.Bahkan kadang-kadang jarum dapat menunjukkan sampai 50 mikro ampere, yang membuat jarum bergerak penuh ke kanan.
Ini sel surya dapat menghasilkan 50 mikro ampere dengan tegangan 0,25 V, ini berarti bahwa dapat menghasilkan daya sebesar 12,5 watt mikro.12,5 mikrowatt adalah ukuran sel sebesar 0,01 m2 atau 1,25 milliwatt per m2.
ndependent Power Solar CellMenghasilkan listrik di rumah? Hal ini dimungkinkan oleh instalasi sel surya, sel surya mengubah cahaya matahari menjadi listrik. Listrik disimpan dalam baterai, saklar baterai lampu.
Dalam penggunaan sel surya untuk menghasilkan listrik di rumah, ada beberapa hal yang perlu kita perhatikan karena karakteristik sel surya:
* Sel surya membutuhkan sinar matahari. Tempatkan sel surya pada posisi di mana tidak terhalang oleh benda sepanjang pagi sampai sore.* Solar Cell - sel surya menghasilkan listrik arus searah, DC.* Untuk efisiensi yang lebih tinggi, gunakan lampu DC seperti lampu LED.* Instalasi kabel baru untuk arus searah, DC untuk perangkat berikut seperti: pencahayaan berbasis LED (Dioda Emiting Light), kamera CCTV, wifi (fideliity nirkabel), dll.
Ketika kita membuat rumah baru, disarankan untuk menggunakan listrik dan sel surya.Sel surya digunakan untuk penerangan parsial (dalam hal ini menggunakan arus DC langsung) dan listrik untuk bolak perangkat saat ini seperti AC: AC, Kulkas, pencahayaan beberapa dll
Ketika daya DC disimpan dalam baterai untuk menggunakan perangkat pada gilirannya AC: pompa air, kulkas, dll perlu bahwa inverter dapat mengkonversi daya DC menjadi AC. Sesuaikan daya Anda perlu diperlukan oleh sel surya, inverter, baterai.LED lampu sebagai pencahayaan Rumah
Saat ini sudah menggunakan lampu hemat energi seperti lampu LED, DC. Bandingkan 3 Watt lampu LED setara dengan 15 Watt AC Lighting.
Kekurangannya adalah:* Instalasi kabel baru untuk lampu LED.
* Biaya pengadaan lampu yang lebih mahal.
Keuntungannya adalah:* Penggunaan energi kecil* Keandalan dari lampu LED 10 x lampu biasa standar* Gunakan dua kabel inti listrik.
AC LampuLampu LEDVoltaseVAC 22012 VDCWatt 15 Watt3 WattLifetime6.000 jam50.000 jamBiaya+ Rp. 25.000 + Rp. 250,000Solar Cell untuk AC Listrik
Jika kita ingin menggunakan energi dari sel surya untuk peralatan rumah lainnya, mengikuti contoh perhitungan berikut.
Jika kita mengambil kekuasaan bolak arus listrik di 2000W selama 10 jam per hari (20KWh/hari) maka diperlukan 24 panel sel surya dengan kapasitas masing-masing 210WP dan 30 @ 12V 100Ah baterai. Hal ini didasarkan pada perhitungan energi surya dari jam 7 pagi sampai jam 5 sore (10 jam) dan asumsi konversi energi minimal 4 jam sehari
.Energi matahariJumlah sel suryaKapasitas sel suryaPerhitunganMengakibatkan4 jam24 panel210 Watt4 x 24 x 21020,160 Watt jamDasar untuk menghitung jumlah baterai 2 x 3 x kebutuhan listrik.
Adanya multiplier 3 untuk mengantisipasi saat hujan / mendung terus menerus selama tiga hari berturut-turut. Sedangkan faktor multiplikasi 2 karena baterai harus tidak lebih dari 50% kehilangan kapasitas jika ingin baterai tahan lama, terutama untuk suatu gel jenis baterai kering dan RUPS. Dengan kata lain bekerja keras untuk DOD (Depth of Discharge) tidak melebihi 50% karena mempengaruhi waktu hidup dari baterai itu sendiri.
Jumlah bateraiVoltaseAmperPerhitunganMengakibatkan10012 Volt100 Ampere jam100 x 12 x 100 Watt 120.000 jam