The Savant® SmartLighting 2 with PoE (SSL-P002) Quick Reference Guide provides all the steps necessary to operate the SSL-P002. The SSL-P002 supports up to 40 keypads through the SKL-4000 and 12 keypads through the SKL-1000. The SSL-P002 supports Power over Ethernet (PoE) using the PoE IEEE 802.3af standard.

Box Contents(1) SmartLighting 2 Controller with PoE (SSL-P002-00)(1) Installation Kit (075-0134-xx) (8) Flat Phillips Screws - #6 x 1/4 (039-0143-xx) (2) Side Mount Brackets - pair (071-0625-xx)Quick Reference Guide (this document)

SpecificationsEnvironmentalEnvironmental

Temperature 32° to 104° F (0° to 40° C)

Humidity10% to 80% Relative Humidity (non-condensing)

Cooling2 cubic feet per minute (CFM) recommended.

Maximum BTU 10 BTU/hr

Dimensions and WeightDimensions and Weight

Height 1.59 in (4.04 cm)

Width 4.32 in (10.96 cm)

Depth 6.50 in (16.51 cm)

Weight 3 lb (1.36 kg)

Rack Space 1U

PowerPower

Power over Ethernet (PoE) IEEE 802.3af

Power Supply(Optional)

5V DC 1.25A 120-240V AC 50/60 Hz

Maximum Power 5 watts

RegulatoryRegulatory

Safety and Emissions FCC Part 15 | CE Mark | C-Tick

RoHS Compliant

Minimum Supported ReleaseMinimum Supported Release

Savant OS da Vinci 5.0.2

Front Panel

Ground Connector - used to connect to a suitable ground reference when using Power over Ethernet.

CPU Status LED

Green: SSL-P002 is operating normally.Green Flashing: Controller is starting.Off: Unit is rebootingRed: Firmware update has failed and unit will be rebooted.Red Flashing: No IP Address/Connecting to Network.Amber: Firmware update in process.Amber Flashing: Controller has a link-local IP Address. This applies to controllers that are not connected to an active router and may be connected directly to a computer.

5VDC

Reset

Station

Ethernet

Module

A B

C D

E F G H

Reset ButtonPress and hold for 5 seconds while powered On to clear network settings. Status LED will blink rapidly when reset is complete.

PoE/Ethernet10/100 Base-T auto-negotiating port with Link/Activity LEDs: 8-pin RJ-45 female.

Link LED

Off: Ethernet link is not established.Green Solid: Ethernet link is established.Green Blinking: Ethernet activity is occurring.

Date Rate LED

Off: 10 Mbps data rateGreen: 100 Mbps data rate

StationUsed to communicate with SKL-1000 and SKL-4000 via RS-422. See Station and MOD Pinouts.

ModuleUsed to communicate with SmartLighting module via RS-422.

Power Input5V DC 1.25A - Connect to optional power supply when not using PoE.

Cable Tie Mount

Holds the power cable with the cable tie.

Note: The SSL-P002 Station port defaults to RS-422 but is configurable to RS-232 by a Savant dealer. For more details, see Changing the Serial Port.

SSL-P002-00 | 009-0668-02 | 150714SSL-P002-00 | 009-0668-02 | 150714 45 Perseverance Way, Hyannis, MA 02601Copyright © 2015 Savant Systems, LLC 1 of 3 savant.com | 508.683.2500

SmartLighting 2 Controller with PoEQuick Reference Guide

Wiring and Connections

RS-232 Pinouts

Note:CTS/RTS Handshaking availability based on component profile.

Station and MOD Pinouts

IMPORTANT! The maximum total length of Cat 5 cable used between the SmartLighting Module connection and the Transorb board is 4000 feet.

RJ-45 to DB9 AdaptersSavant offers RJ-45 to DB9 adapters in a variety of configurations that can be used for RS-232/422 control. Refer to the RS-232 Conversion to DB9 and RS-422/485 Pinout Application Note located on the Savant Community for more information on RJ-45 to DB9 adapters.

IMPORTANT! If you are using RJ-45 to DB9 adapters not supplied by Savant:

• Ensure that any wires required for communication/control are terminated within the adapter.

• Ensure that all wires NOT required for communication/control are NOT terminated in the connector.

• Ensure that the unused wires in the connector are cut to prevent them shorting out, as they are still terminated in the RJ-45 connector on the controller side.

GPIO and Relay Wiring

GPIO Connector Pinout Relay Connector Pinout

Savant requires the use of business class/commercial grade network equipment throughout the network to ensure the reliability of communication between devices. These higher quality components also allow for more accurate troubleshooting when needed.

Device Network ConnectionsConnect all Savant devices to the same local area network (LAN) or subnet as the host. Savant recommends not implementing any type of traffic or packet shaping in your network topology for the Savant devices as this may interfere with performance.

Managing IP AddressesTo ensure that the IP Address will not change due to a power outage, a static IP Address or DHCP reservation should be configured. Savant recommends using DHCP reservation within the router. By using this method, static IP Addresses for all devices can be managed from a single UI avoiding the need to access devices individually.

Setting a Static IP AddressRefer to the Retrieving and Setting IP Addresses for Savant Devices - Application Note located on the Savant Customer Community.Setting DHCP ReservationSetting DHCP reservation varies from router to router. Refer to the documentation for the router to configure DHCP reservation.

Network ChangesSavant recommends performing one of the following steps to refresh the IP connection after connecting to a new network, changing routers, or if the IP Address range is changed in the current router. This will reset any IP connection and ensure that the host is communicating with the network correctly.• Cycle Power

1. Disconnect the controller from the AC power source2. Wait 15 seconds and then reconnect.

• Hot Plug the Ethernet (LAN) Connection1. Disconnect the Ethernet (LAN) connection from the controller.2. Wait 15 seconds and then reconnect.

Station and MOD (Module) Serial ProtocolThe station and module ports default to RS-422 but can be configured for RS-485 based on the needs of the configuration.To change the station and module port protocol, access the SSL-P002 Web User Interface (Web UI).1. From a Web browser on the Savant Development Environment (SDE),

enter the IP Address of the SmartLighting controller.2. Log in to the controller’s Web UI:

User name: RPMPassword: RPM

3. Select Serial Ports in the left sidebar.

4. Make the appropriate selections for the configuration.5. Click Set.

SSL-P002-00 | 009-0668-02 | 150714SSL-P002-00 | 009-0668-02 | 150714 45 Perseverance Way, Hyannis, MA 02601Copyright © 2015 Savant Systems, LLC 2 of 3 savant.com | 508.683.2500

InstallationThe SSL-P002 can be placed on a 1U rack shelf, wall mounted using the side-mounting brackets (included) or rack mounted using RMB-0025 brackets (optional).

Wall MountingSide mounting brackets are shipped with the SSL-P002.Use the supplied screws to install the brackets to the SSL-P002 as shown.

Side Wall Mounting Brackets (Included)

Rack Mounting Bracket -RMB-0025-xx (Optional)Use the supplied screws to install the faceplate to the SSL-P002 as shown.

Additional InformationRefer to the following documents located on the Savant Community for additional information.• SmartLighting Control (SSL-P002, SSL-P018) - Deployment

Guide

SSL-P002-00 | 009-0668-01 | 150709SSL-P002-00 | 009-0668-01 | 150709 45 Perseverance Way, Hyannis, MA 02601Copyright © 2015 Savant Systems, LLC 3 of 3 savant.com | 508.683.2500