Sliding Door OperatorEM SL

User ManualOriginal instructions

CONTENTS

4Congratulations on your new automatic door! ........................................................................

4Electronic equipment reception interference ...........................................................................

4Environmental requirements ..........................................................................................................

4Product liability ...................................................................................................................................

5Service .....................................................................................................................................................

5Intended use .........................................................................................................................................

5How the EM SL works .........................................................................................................................

5Locking ....................................................................................................................................................

6Unlocking ...............................................................................................................................................

7Programme selectors .........................................................................................................................

8Technical specification ......................................................................................................................

8Integrated safety ..................................................................................................................................

9Emergency escape ..............................................................................................................................

10Regular safety checks .........................................................................................................................

13Safety accessories ................................................................................................................................

13General accessories ............................................................................................................................

15Troubleshooting ..................................................................................................................................

16Maintenance plan ...............................................................................................................................

16Other products from Entrematic Group .....................................................................................

17Declaration of conformity ................................................................................................................

© All rights in and to this material are the sole property of Entrematic Group AB. Copying, scanning, alterations ormodifications are expressly forbidden without the prior written consent of Entrematic Group AB. Rights reservedfor changes without prior notice.

Backtrack information: folder:Workspace Publish old version, version:a5, Date:2014-08-08 time:12:03:10, state:Working

1005274-EMEI-7.0Issue 2014-08-082

Instructions for safe operation

• Failure to observe the information in this manual mayresult in personal injury or damage to equipment.

• To reduce the risk of injury of persons - use this oper-ator only with pedestrian doors.

• Do not use the equipment if repair or adjustment isnecessary.

• Disconnect supply when cleaning or other mainten-ance is to be carried out.

• The operator can be used by children age 8 and above,and persons with reduced physical, sensory or mentalcapabilities, or lack of experience and knowledge, ifthey have been given supervision or instruction by aperson responsible for their safety concerning safeoperator use and the possible hazards involved.This does not however prevent those persons to usethe door where the operator is installed.

• Cleaning and user maintenance shall not be made bychildren without supervision.

• Do not let children climb on or play with the door orthe fixed/remote controls.

3Issue 2014-08-081005274-EMEI-7.0

Congratulations on your new automatic door!Entrematic Group has developed automatic doors for more than 50 years. State-of-the-art technologyand carefully tested materials and components provide you with a superior product.As with all other technical products, your automatic door requires periodic maintenance and service.It is essential that you know your automatic door (system) and that you recognize the importanceof maintaining it in compliance with applicable standards for safety.Your local Entrematic Group-authorized representative is familiar with these standards, as well asall applicable local codes and Entrematic Group recommendations for power-operated pedestriandoors. Service and adjustments performed by your Entrematic Group-authorized representative,will ensure safe and proper operation of your automatic door unit.

Electronic equipment reception interferenceThe equipment complies with the European EMC directive (US market FCC Part 15), provided installedaccording to Installation and Service manual.The equipment may generate and use radio frequency energy and if not installed and used properly,it may cause interference to radio, television reception or other radio frequency type systems.If other equipment does not fully comply with immunity requirements interference may occur.However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct the interference by oneor more of the following measures:

• Re-orient the receiving antenna.• Relocate the receiver with respect to the equipment.• Move the receiver away from the equipment.• Plug the receiver into a different outlet so that equipment and receiver are on different branch

circuits.• Check that protective earth (PE) is connected.If necessary, the user should consult the dealer or an experienced electronic technician for additionalsuggestions.

Environmental requirementsEntrematic Group products are equipped with electronics and may also be equipped with batteriescontaining materials which are hazardous to the environment. Disconnect power before removingelectronics and battery and make sure it is disposed of properly according to local regulations (howand where) as was done done with the packaging material.

Product liabilityAccording to regulations, the following are the responsibility of the owner or caretaker of theequipment

• that the equipment operates correctly, so that it gives sufficient protection in regard to safetyand health

• that the equipment is operated and regularly maintained, inspected and serviced by someonewith documented competence in the equipment and in applicable regulations

• that a journal is kept of inspection, maintenance and service records including the provider• that inspection covers the emergency opening function (when applicable)• that the closing force is appropriate for the door size on fire-approved door systems (when ap-

plicable)

1005274-EMEI-7.0Issue 2014-08-084

ServiceRegular inspections by a trained and qualified person, and the frequency of service occasions, shouldat minimum be made according to national regulations or industry standard, in the absence of anational regulation. This is especially important when the installation concerns a fire-approved dooror a door with an emergency-opening function. To extend the life of your investment and ensuresafe and reliable operation of the door, we recommend a minimum of 2 visits per year or more, de-pending on usage and operating conditions. Environmental aspects shall also be considered.Talk to your Entrematic Group representative to learn more about our service offering.

Intended useThe EM SL is an automatic sliding door operator developed to facilitate entrances to buildings andwithin buildings through sliding doors.The door is designed to offer continuous use, a high degree of safety and maximum lifetime. Thesystem is self-adjusting to the effects caused by normal variations in the weather conditions and tominor friction changes caused by e.g. dust and dirt.It is to be used indoors where it is suitable for almost all types of external and internal sliding doors.Ensure that the lock is only activated when there are no persons in the room.

For installation and maintenance see Installation and Service manual 1004572.Save these instructions for future reference.

How the EM SL worksThe EM SL works electromechanically. The drive unit, control unit, transmission, optional emergencyunit and electromechanical locking device are all assembled in a support beam with an integratedcover. The motor and gear box transmit movement to the door leaves by means of a tooth belt. Thedoor leaf is fitted to a door adapter/carriage and hangs on a sliding track. The active leaf travel isdirected by a floor guide.When an opening impulse (e.g. from a motion sensor) is received by the control unit, the drive unitstarts and transmits movement to the door leaves to open.The closing starts when no OPENING IMPULSE is received, the HOLD OPEN TIME has ended and noPRESENCE IMPULSE is activated.The EM SL user can select five different modes of operation if a programme selector is installed. SeeProgramme selectors on page 7.

LockingDoors used for emergency escape in buildings such as hospitals and homes for elderly people maynot be locked or put in programme selection OFF mode. In other buildings emergency escape doorsmay be locked or put in programme selection OFF mode after it has been secured and all peoplehave left the building.

5Issue 2014-08-081005274-EMEI-7.0

UnlockingUnlock all the mechanical locks before activating the operator.

1 2

1005274-EMEI-7.0Issue 2014-08-086

Programme selectorsThe door functions are set with different key programme selectors. The key must always be removedon emergency escape doors after changing settings.

Surface mounted

PSMB-5

PS-5M

PS-6PSMB-5PS-5M

Flush mounted

PSMB-5

PS-5M

Programme selector functions

This function is only used on emergency escape doors after it is certainthat all people have left the building.The door cannot be opened with inner and outer activation units. Thedoor is locked if an electromechanical locking device has been fitted. Thedoor can be opened partially with a key switch (if fitted). With an emer-gency push-button (if fitted) the door opens fully.

OFF

Passage from inside only. The door is normally locked if an electromech-anical locking device has been fitted. The door can only be opened withthe inner activation unit or with a key switch/emergency push-button (iffitted).

EXIT

Two-way traffic, normal operation of the door. The door can be openedwith the inner and outer activation units and with a key switch/emergencypush-button (if fitted).

AUTO

Two-way traffic, AUTO PARTIAL is obtained. The door can be openedpartially with the inner and outer activation units and with a key switch(if fitted). With an emergency push-button the door opens fully.

AUTOPARTIAL

The door is permanently open. The door can be moved by hand e.g. forwindow cleaning. All activation units except for the emergency pushbutton (if fitted) are disconnected.

OPEN

Set the programme selector to AUTO. Insert a narrow object in the smallhole on the programme selector and push briefly. The operator makes asystem test of the emergency unit (if selected), electromechanical lock,watchdog relay and closed door position. The operator is after closingreset and ready for normal operation.

RESET

PSO-5R

PSO-5T

PSMB-5

Note! The RESET is not available on programme selector PS-5M.

7Issue 2014-08-081005274-EMEI-7.0

Turn the key clockwise to the position “R” (six o’clock) and insert a narrowobject in the small hole on the programme selector and push briefly. Thenturn the key counter-clockwise back to the requested setting. The oper-ator makes a system test of the emergency unit (if selected), electromech-anical lock, watchdog relay and closed door position. The operator is afterclosing reset and ready for normal operation.

RESET

PS-6

Note! The key cannot be removed in the "R" position.

Note! If monitored emergency unit is a demand, a test of the emergency unit is performed whenthe programme selector is turned from OFF or OPEN to any other position.

Technical specification

Entrematic Group ABManufacturer:Lodjursgatan 10, SE-261 44 Landskrona, SwedenAddress:EM SLType:120 - 240 V AC 50/60 Hz, mains fuse max 10AMains power supply:Max. 250 WPower consumption:IP20Degree of protection:Third party approvals from established certification organizations validfor safety in use, see Declaration of Incorporation.

Approvals:

Integrated safetyTo permit a safe passage between closing doors, the doors reverse immediately if an obstruction isdetected. They then resume their interrupted movement at low speed to check whether the obstruc-tion has disappeared or not.

If an obstruction is detected between opening doors and surrounding walls or interior fittings, thedoors stop immediately, and then close after a time delay.

1005274-EMEI-7.0Issue 2014-08-088

Emergency escapeThe operator can be fitted with different emergency escape units to ensure a safe evacuation of thebuilding.

Break-out unit PSBThe door leaves and the side screens are swung outwards when a defined pressure is applied.The break-out function can also be used to create a wider opening. From the fully swung out position,the door leaves can be manually slid sideways, offering the possibility to transport wide objectsthrough the opening, or to make a shop entrance more inviting during good weather.

Mechanical emergency unit (MEU)An elastic cord is used to open the door in the event of power failure. Until the power is restored,the door remains open. The operator will then resume the function set by the programme selector.The emergency unit is monitored by the operator control unit. A monitoring error means that thedoor opens and remains open until the error is cleared.For further information, see General accessories on page 13.

Electrical emergency unit (EEU)The door is opened by means of a rechargeable battery unit in the event of a power failure. The doorremains in this position until the power is restored. The operator will then resume the function setby the programme selector. The emergency unit is monitored by the operator control unit. A mon-itoring error means that the door opens and remains open until the error is cleared.For further information, see General accessories on page 13.The electrical emergency function can also be used to close the door in the event of power failure.The fire authorities make this a requirement to stop fire or smoke from spreading throughout thebuilding.

9Issue 2014-08-081005274-EMEI-7.0

Regular safety checksTo help you fulfil the national/international requirements and to avoid malfunction and risk for in-juries, we have provided the following checklist.

Do not use if repair or adjustment is necessary.

Disconnect supply 12 when cleaning or other maintenance is to be carried out.

If problemoccursDaily Action

Activate your operator and visually check, fastening of• operator and cover 1• cables 2• programme selector(s) 3• door and glass (stability) 4

Also inspect your operator and check visually for• condition of door seals and weather stripping 5

• condition of glazing rubbers 6• finger protection 7

• proper operation; closes slowly and smoothly• any ventilation being obstructed

Set the programme selector to OFF and check that the operator and electromechanical lock (if fitted)

work together. Also check that the lock 8 really secures the door.

Activate the manual activation units 9 , if any, and walk towards the door. Check that the door hasopened appropriately while you pass the entrance/exit.

Then proceed with the automatic activation units 10 in the same way.

Check the safety sensors 11 if any.If you are unsure of which type of sensor you have, please contact your Entrematic Group repres-entative.

If the operator is equipped with break-out system, set the programme se-lector to AUTO mode. Push the door manually while in the escape directionto ensure that nothing prevents the door from being open. Also ensure thatthe escape route is free for use. After the test, restore the door(s) to theirnormal mode of operation.

Byla

w,t

hese

test

smus

tbe

perfo

rmed

regu

larly

bytr

aine

dpe

rson

nel.

Escapedoors

If the operator is equipped with automatic opening system, shut off thepower and the door should open and remain open. Restore power and thedoor should close.

Let the door close after an impulse ensuring nothing prevents the door fromclosing and locking (if regulations require it).Fire

doors

Take appropriate measures.=

Contact your Entrematic Group representative. For contact information, see last page.=

1005274-EMEI-7.0Issue 2014-08-0810

FUNCTION AND VISUAL INSPECTION

Click!

ILL-01798

12

11 1

4

10 11

9

11

2

8

9

6

≥ 25

5

5 7

3

CLEANING

The best way to remove dust and dirt from the EM SL is to use water and a soft cloth or a sponge. A gentle deter-gent may be used. To maintain the quality of the enamel layer, the surfaces should be cleaned once/four monthsperiod. The cleaning should be documented. To avoid damages to the profiles the brushes/weather strippingmust be vacuum-cleaned weekly.

• Do not expose windows, doors or profiles to alkalis. Both aluminium and glass are sensitive to alkalis.• Do not clean with high pressure water. Operator, programme selector and sensor may be damaged and

water may enter the profiles.• Do not use polishing detergent.• Do not scrub with materials like Scotch-brite, as this will cause mechanical damage.

11Issue 2014-08-081005274-EMEI-7.0

SIGNAGE

TYPE

ART. NO.

YEAR+WEEK

Landskrona Sweden

Factory No. 1

1004083

XXXXXXX

XXXXXXX

XXXX

CLASSIFICATION DIN 18650

1 23 4

5 67 8

XX

EN ISO 9001 Certificate No: 911828, 956538

SITAC1422

xxxxxxxxxxxxx

xxxxxxxxxxxxx

SÜD

xxxxxxxxx

1002

XXXXXX

XX/XXHz

PROJECTSERIAL NO.

XXX

XXX

W

XXXA

VAC

80

0 m

m

xxxxxxxxxxxxxxxxxxxxxxxxxx

SÜD

TYPEART. NO. YEAR+WEEK

10

04

19

7

XXXXXXX XXXXXXX XXXX

CLASSIFICATION DIN 18650

1 2 3 4 5 6 7 8

SITAC1002

xxxxxxxxxxxxxx

1002

XXXXXX XX/XXHzPROJECT

SERIAL NO.

XXXXXXXXXXW

XXXXAVAC

LAN

DS

KR

ON

A S

WE

DE

N

FA

CT

OR

Y N

O.

X

TM

xxxxxxxxxxxxxxxxxxxxxxxxxx

SÜD

TYPEART. NO. YEAR+WEEK

10

04

19

7

XXXXXXX XXXXXXX XXXX

CLASSIFICATION DIN 18650

1 2 3 4 5 6 7 8

SITAC1002

xxxxxxxxxxxxxx

1002

XXXXXX XX/XXHzPROJECT

SERIAL NO.

XXXXXXXXXXW

XXXXAVAC

LAN

DS

KR

ON

A S

WE

DE

N

FA

CT

OR

Y N

O.

X

TM

Click!

F

C

J

G

H

B

E

D

ILL-01777

Automatic door

Automatic door

Keep clear

Keep clear

No entry

No entry

Click!

A

A

If problemoccursAction

Check that all required signage is applied and intact. Mandatory indicates that the signage is re-quired by European directives and equivalent national legislation outside the European Union.

Product label: MandatoryA

Emergency break-out: Mandatory, if approved for escape route.B

Entrematic Group door sticker: Mandatory, if applicable to highlight the presence of theglass (applied to all glass sections that are moving).

C

Supervision of child: Mandatory, if applicable (applied to both sides of the door). To beplaced on entrances where the risk analysis shows use by children, elderly and disabled.

D

Operator designed for disabled people:Recommended, if applicable (applied to both sides of the door)

E

Activation by disabled people: Recommended, if applicableF

No entry, identifying one-way traffic: Mandatory in GB and US, if applicableG

Automatic door: Only mandatory in GBH

Keep clear: Only mandatory in GBJ

Contact your Entrematic Group service representative. For contact information, see last page.=

1005274-EMEI-7.0Issue 2014-08-0812

Safety accessoriesEven though the EM SL is installed to comply with all applicable safety regulations, it is possible toenhance safety/comfort with the following add-ons (please contact your local Entrematic Groupcompany for detailed description).

• Combined motion and presence sensors• Separate presence sensors

General accessoriesYour EM SL can be further improved with the following add-ons (please contact your local EntrematicGroup company for detailed description).

• CoverMade in clear anodized aluminium as standard. Paint finished in RAL colours or anodizing op-tional.

• Motion and presence sensors, see separate manuals or installation drawings.• Programme selectors

See page 7.• Electrical locks

Locked with power, locked without power or bistable lock.• Manual unlocking device

For manual unlocking of the electrical lock, locked without power.• Micro switch kit

For indication of door and lock position.• Locked door indicator

For indication of locked lock and closed door for connection to alarm system.• Electrical emergency unit with batteries

Used if a door is required to be opened or closed by means of a rechargeable battery unit andremain in this position in the event of power failure. Authorities can demand that the emergencyunit is monitored on a regular time basis. Half an hour before this time has elapsed the followingopening impulse generates an emergency opening test. If there is no opening impulse withinthe next half hour, the operator control unit generates the opening impulse itself.If the battery opens the door within the limited time the test is successful and the door resumesthe function set by the programme selector.

Note! The test is never performed in programme selector setting OPEN. In setting OFF it can beselected. The test is always performed after a RESET and after changing program selection, froma position where a test is not done to a position where the test is a demand.

• Electrical emergency unit with batteries and two motorsUsed if a door is required to be opened by means of a rechargeable battery unit and remain inthis position in the event of power failure. Authorities can demand that the emergency unit ismonitored on a regular time basis. Half an hour before this time has elapsed the followingopening impulse generates an emergency opening test. If there is no opening impulse withinhalf an hour, the operator control unit generates the opening impulse itself.If the battery opens the door within the limited time the test is successful and the door resumesthe function set by the programme selector.

Note! The test is never performed in programme selector setting OPEN. In setting OFF it can beselected. The test is always performed after a RESET and after changing program selection, froma position where a test is not done to a position where the test is a demand.

13Issue 2014-08-081005274-EMEI-7.0

• Emergency closing with repeated closingIf the door is opened by hand after an electrical emergency closing, it will close again.

• Mechanical emergency unit with elastic cordUsed if a door is required to be opened and remain opened by means of an elastic cord in theevent of power failure. Authorities can demand that the emergency unit is monitored on a reg-ular time basis. Half an hour before this time has elapsed the following opening impulse generatesan emergency opening test. If there is no opening impulse within half an hour, the operatorcontrol unit generates the opening impulse itself.If the elastic cord opens the door within the limited time the test is successful and the door re-sumes the function set by the programme selector.

Note! The test is never performed in programme selector setting OPEN. In setting OFF it can beselected. The test is always performed after a Reset and after changing program selection, froma position where a test is not done to a position where the test is a demand.Break-out unit PSBEnables the door/side screens to be broken outwards in case of emergency by applying a definedpressure.

• Break-out unit PSBEnables the door/side screens to be broken outwards in case of emergency by applying a definedpressure.See page 9.

• InterlockingUsed between two operators when the first operator must close before the other one can open(typical to reduce energy losses and not for security reasons). EXU-4 required.

• Convenience battery UPSStand-by supply which gives continued operation during short power failure. EXU-3 or EXU-4required.

• Emergency openingOpens the door in any programme selector setting (fireman's opening). EXU-4 required.

• External error or status indicationObtained if a lamp or a buzzer is connected. EXU-4 required.

• Key switches (flush and/or surface mounted)Used to give opening impulse to the door in any programme selector setting. With electricalemergency unit also during power failure.

• Push buttonUsed to give opening impulse to the door.

• SynchronizationUsed between the operators of two single sliding doors, working together in very large openings.

1005274-EMEI-7.0Issue 2014-08-0814

Troubleshooting

RemediesWhat´s wrong?

The door does not open

Change the setting of the program selector.The motor does not start

If break-out unit PSB is installed, check that the door leaves and side screensare completely closed.

Check the mains switch and fuse in the building.

Unlock the mechanical locks.The motor starts but stops duringopening Clean the floor guide.

Check for objects jammed under the door.

The door does not close

Change the setting of the program selector.The motor does not start

If a presence sensor is installed, check for and remove objects placed in thepresence zone.

Clean the floor guide.The motor starts but stops duringopening Check for objects jammed under the door.

The door moves slowly

Prevent traffic using the door and allow it to do a complete opening andclosing cycle with low speed.

Reset the operator by setting the programme selector to AUTO and pushinga narrow object in the small hole on the programme selector.

Allow the operator to control the closed position without interruption.

If the problem continues, please contact your Entrematic Group representative.

15Issue 2014-08-081005274-EMEI-7.0

Maintenance planAs mentioned earlier in this manual, service and adjustments performed by your EntrematicGroup-authorized representative will ensure safe and proper operation of your automatic door unit.The table below shows the recommended interval in months, when to replace parts during preventivemaintenance.

AbusiveEnvironment

Cycles/hour in operation

Part numberPart >100<100<10

Hightraffic

Mediumtraffic

Lowtraffic

2424242433550475

Electrical emergency unit bat-tery

12121212331700121

Mechanical emergency unitelastic cord

6612243383006433831622830792

Floor guide shoeStandardFelt paddedBreak-out

1212243633100052533550716

Carriage wheelDoubleAnti-derailing

1224364833701596Sliding track2436486033735251Tooth belt

Other products from Entrematic Group• Door Systems• Sliding doors• Swing doors• Automatic and manual activation units

1005274-EMEI-7.0Issue 2014-08-0816

WeEntrematic Group ABLodjursgatan 10SE-261 44 LandskronaSweden

declare under our sole responsibility that the type of equipment:

EM SL Single or Double, EM SL T Single or Double. With or without emergency unit

complies with the following directives:

2006/95/EC Low Voltage Directive (LVD)2004/108/EC ElectroMagnetic Compatibility Directive (EMCD)2006/42/EC Machinery Directive (MD)

Harmonized European standards which have been applied:

EN 16005EN ISO 13849-1EN 61000-6-3EN 61000-6-2EN 60335-1

Other standards or technical specifications, which have been applied:

FCC 47 CFR Part 15 BDIN 18650-1/-2BVLBBR

EN 60335-2-103

EC type examination or certificate issued by a notified or competent body (for full address, please contact EntrematicGroup AB) concerning the equipment:

SITAC 0145/05SITAC 0137/05

TÜV B 12 07 74969 007SITAC 0147/05

The manufacturing process ensures the compliance of the equipment with the technical file. The manufacturingprocess is regularly assessed by 3rd party.

Compilation of technical file:

Email: johnny.persson@entrematic.comJohnny PerssonEntrematic Group ABLodjursgatan 10

Declaration of conformity

17Issue 2014-08-081005274-EMEI-7.0

SE-261 44 LandskronaSweden

PositionSignatureDatePlaceProduct Safety & Liability ManagerJohnny Persson2013-05-07Landskrona

DoC 1000190-EMEI-7.0

Entrematic Group AB, Lodjursgatan 10, SE-261 44 Landskrona, Sweden

Tel: +46 10 47 48 300 • Fax: +46 418 201 15

www.entrematic.com • info.em@entrematic.com