SLIDEWHIZZER DOME CLIMBER WITH 6' SLIDE (55 INCH …Hexagon Mat - 55 inches in diameter (x 1)...
Transcript of SLIDEWHIZZER DOME CLIMBER WITH 6' SLIDE (55 INCH …Hexagon Mat - 55 inches in diameter (x 1)...
SLIDEWHIZZER
DOME CLIMBER WITH 6' SLIDE
(55 INCH HEXAGON MAT)
page 1 of 19
CUSTOMER SERVICE INFORMATION
Thank you for purchasing:
SLIDEWHIZZER DOME CLIMBER WITH 6' SLIDE
MODEL# SWSC-01
Platports® strives for 100% satisfaction guarantee, as customer satisfaction is of utmost
importance to us. Before assembly, we suggest you to review all the components of the
product you have purchased and contact us within 30 days of purchase for replacement
parts. We will replace all missing or damaged parts at no extra charge.
To submit a request for a replacement part, please include the following information:
Name:
Mailing address:
Product name:
Product model:
Part #:
Retailer where purchase was made:
Date of purchase:
Order #:
Quantity:
Please note that replacement part requests require a photo for submission.
If you wish to request a replacement part, have other questions or concerns about this product
or order additional parts, please contact us at:
PLATPORTS
PO BOX 501553 San Diego, CA, 92150
page 2 of 19
LIMITED WARRANTY
Platports® warrants this product to be free from defects in workmanship and materials under normal use and
conditions for a period of 90 DAYS FROM THE DATE OF ORINGINAL PURCHASE. This Limited Warranty is not
transferable and is available only for the original purchaser of the Product. The Company's obligation under this
warranty is limited to replacing or repairing the Product, at the discretion of the Company.
All warranty coverage extends only to the original retail purchaser from the date of purchase, Platports® obligation
under this warranty is limited to replacing or repairing at Platports® option.
All products for which a warranty claim is made must be received by Platports® and accompanied by sufficient
proof of purchase (photocopy of the original store receipt, indicating the date of purchase). All freight and
handling fees are the responsibility of the customer to pay, both to and from Platports®. All warranty claims
must be preauthorized by Platports®. Preauthorization can be obtained by contacting Platports®
This warranty does not cover ordinary wear and tear, weathering, failure to follow directions, improper installation,
improper maintenance, or acts of nature, (such as damage caused by wind, lightning, snow, water or ice).
Weather damage, damage caused by unauthorized repair work or damage caused by improper use of the products
are not covered by the product warranty. No other warranty beyond that specifically set forth above is authorized
by Platports®
Platports®IS NOT RESPONSIBLE OR LIABLE FOR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGE RISING OUT
OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PRODUCT OR OTHER DAMAGE WITH RESPECT
TO ANY ECONOMIC LOSS, LOSS OF PROPERTY, LOSS OF REVENUE OR PROFITS, LOSS OF ENJOYMENT OR USE,
COST OF REMOVAL, INSTALLATION OR OTHER CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.
ACCORDINGLY, THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THE WARRANTY EXTENDED HEREUNDER IS ALL
IN LIEU OF OTHER WARRANTIES AND Platports®, SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF
MERCHANTABILIY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN ITS SCOPE AND DURATION TO
THE TERMS SET FORTH HEREIN.
WHILE EVERY ATTEMPT IS MADE TO ENSURE THE HIGHEST DEGREE OF PROTECTION IN ALL EQUIPMENT, WE
CANNOT GUARANTEE FREEDOM OF INJURY. THE USER ASSUMES ALL RISK OF INJURY DUE TO USE.
ALL MERCHANDISE IS SOLD ON THIS CONDITION, WHICH NO REPRESENTATIVE OF Platports®CAN WAIVE OR CHANGE.
page 3 of 19
WARNINGS
WARNINGS:
While every attempt is made to ensure the highest degree of protection in all equipment,
freedom from injury cannot be guaranteed. The user assumes all risks of injury due to use. It is
on this condition that all merchandise is sold, which cannot be changed or waived by any
representatives of the company.
WARNING - PLEASE READ
ADULT ASSEMBLY REQUIRED
CHOKING HAZARD - Small Parts
NOT for children under 3 years of age.
page 4 of 19
WARNINGS
Please read the information in this manual in its entirety.
Noncompliance to the instructions may increase the risk of serious injury and/or death:
-----------------------
This unit must be assembled and disassembled by ADULTS ONLY.
DO NOT install this equipment over concrete, asphalt, or any other hard or rough surface. A fall onto a hard surface
can result in serious injury. The SLIDEWHIZZER DOME CLIMBER should always be installed over an appropriate,
stable surface (rubber mat, grass, etc). It is recommended that whenever possible the ground anchors are used
and firmly inserted into the ground.
Place this equipment on stable, level surface AT LEAST 7 feet away from any structure, obstruction, or possible
hazard(s) such as walls, pools, power lines, overhangs, other playground equipment, driveways, hard surfaces
and/or roads.
DO NOT attach items to the SLIDEWHIZZER DOME CLIMBER not specifically designed for this purpose by the
manufacturer,(i.e. cables, jump ropes, chains, clotheslines, or leashes) to avoid the risk of strangulation or other
physical injuries.
DO NOT use this product in a way that is other than its intended use.
DO NOT leave children unattended; Children must be supervised at all times when this equipment is in use.
DO NOT allow more than one child on the SLIDEWHIZZER DOME CLIMBER at a time.
DO instruct children to ensure that the chute at the bottom is clear of any obstructions before sliding.
DO NOT place objects on or under the slide.
DO NOT allow people and pets to sit near/under the SLIDEWHIZZER DOME CLIMBER.
DO NOT allow children to stand on the slide chute or top. DO NOT allow children to attempt to walk up the slide or
hang from the steel tubing. Children should ALWAYS be securely seated, in the forward-facing position when sliding.
DO NOT allow children to lay down, slide from a standing position, or slide down the chute backwards.
ALWAYS wear the appropriate footwear [i.e. closed toe] and clothing when using the SLIDEWHIZZER DOME CLIMBER.
DO NOT allow children to wear loose fitting clothing, clothing with straps/loops, backpacks or accessories with straps
or loops, or sharp edges which may present a hazard or become snagged or caught on the SLIDEWHIZZER Dome
Climber during use. Serious injury and/or accidental strangulation may occur.
page 5 of 19
Long pants are recommended for sliding to prevent friction of skin against the chute.
DO NOT allow children to wear glasses or helmets when using the SLIDEWHIZZER DOME CLIMBER.
Examine and replace any worn, loose, defective, rusted or missing parts and/or bolts before use.
It is imperative that all parts are inspected to ensure that they are attached and are in good condition.
If any loose, cracked, missing, or otherwise damaged components are found, refrain from use. If product is removed
for winter storage, reinstall all plastic parts before use.
DO NOT exceed the maximum weight limit of 110lbs (50kgs).
This unit has a maximum fall height of 46.3”
Suitable for use by most children from 3 to 10 years of age.
This SLIDEWHIZZER DOME CLIMBER is NOT for adults or adolescents.
Please read and refer to other warnings in the SLIDEWHIZZER DOME CLIMBER instructions before use.
ASSEMBLY WARNINGS
When you are ready to start, make sure that you have the correct tools at hand, and adequate space for assembly.
Please refer to the table for part descriptions and numbers. The assembly instruction uses these descriptions and
numbers as reference. Make sure you have all parts listed.
IMPORTANT: USE GLOVES TO PROTECT AGAINST PINCH POINTS
Enclosed are the current specifications and product features available DURING ASSEMBLY. at time of printing,
however, changes may be made in equipment, availability, specifications and features without notice.
ASSEMBLY TIPS: Assemble the climber without the washers at the beginning of the assembly process
when the bolts are placed loosely in position. When the unit is fully assembled and bolts are
ready to be tightened, spring washers and washers may then be added
page 6 of 19
A I
M6 15mm bolt (x 2) Black plastic cap (x 2)
R M6 30mm bolt (x 1) Tie bar (Silver) (x 1)
M6 35mm bolt (x 5)
M6 washer (x 4) Top frame tube (Pink)- left (x1 )
M6 Spring washer (x 4) Top frame tube (Pink) - right (x1 )
M6 Domenut (x 6) Center frame tube (Yellow) (x 4)
M8 23mm bolt (x 12) Center frame tube with hole (Yellow) - left (x 1)
M8 x 37mm bolt (x 6) Center frame tube with hole (Yellow) - right
(x 1)
Bottom chute support tube (Silver)
(x 1)
Wavy slide chute (x 1)
G O T1
Handrail tube (Silver) (x 2)
H P T2
E M S2
M8 Spanner (x 1)
F N T
Top frame tube (Pink) (x 5) M8 Domenut (x 12)
D L S1
M6 Spanner (x 1)
M8 washer (x 6)
B J
M8 Spring washer (x 12)
COMPONENT LIST
C K S
Q
page 7 of 19
Bottom frame tube (Blue) (x 5) X
Bottom frame tube with hole (Blue) (x 1)
Hexagon Mat - 55 inches in diameter (x 1)
Climber bend support (Silver) - left (x 5) Y
Plastic knob (x 6)
Climber bend support (Silver) - right (x 5) Z Ground anchor (x 6)
Climber support (Silver) - left (x 1)
TOOL REQUIRED
1. Philips head screw driver
Climber support (Silver) - right (x 1)
2. Combination Wrench 10
W
V1
W1
U
U1
V
COMPONENT LIST
page 8 of 19
ASSEMBLY INSTRUCTIONS
Step 1: Assemble Climber Bend Support (Silver) - Left (V) & Right (W)
1-1. Please find the Climber Bend Support (Silver) - Left (V) & Right (W) X 5 pcs as indicated
below, and place them side by side on the ground.
Climber Bend Support - Left (V) Climber Bend Support - Right (W)
Short slide
(26 inches)
Long Slide
(33 inches)
a. b.
a. b.
Short slide
(26 inches)
Long Slide
(33 inches)
page 9 of 19
1-2. Make an " X " with a Climber Bend Support (Silver)-Left (V) with a Climber Bend Support
(Silver) - Right (W) according to the "correct" figure below. Repeat 4 times with other Climber
Bend Support (Silver)-Left (V) and Right (W) pairs.
Please pay close attention that the shape of the X is in "correct" position.
1-3. Attach loosely Climber Bend Support (Silver) - Left (V) x 5 and Climber Bend
Support (Silver) - Right (W) x 5 together by using bolt (G) x 5 and domenut (K) x 5.
a.
a.
b.
b. CORRECT
Screw bolt(G) and
domenut (K)
loosely in place.
CORRECT INCORRECT
V.S
page 10 of 19
Make sure the support ends (a & b) are turned in the upward direction,
away from the ground.
1-4. Attach loosely Climber Support (Silver)-Left (V1) x 1 and Climber Support (Silver)-right (W1) x 1
together by using bolt (G) x 1 and domenut (K) x 1.
Step 2: Attach Bottom Frame Tube (Blue) - (U) to Climber Bend
Support (Silver) - Left (V) & Right (W)
2-1. Attach Bottom Frame Tube (Blue) - (U) to Climber Bend Support (Silver) - Left (V) &
Right (W) by using bolt (G) x 5 + washer (I) x 5 + spring washer (J) x 5 and domenut (K) x 5.
NOTE: The ends of the Climber Bend Support need to be facing inward.
Make sure the support ends are turned in the upward direction.
page 11 of 19
NOTE: Please beware that one end of Bottom Frame Tube (Blue) needs to
be the inside and the other end needs to be on the outside when assembling.
2-2. Attach Bottom Frame Tube with Hole (Blue) - (U1) to Climber Support (Silver) - (V1) & (W1)
by using bolt (G) x 1 + washer (I) x 1+ spring washer (J) x 1 and domenut (K) x 1.
(See figure 1. below)
Figure 1.
Step 2-2.
NOTE: This side is to connect to 6ft slide.
outside
inside
Same Bottom Frame Tube (Blue)
inside
Same Bottom Frame Tube (Blue)
outside
page 12 of 19
Step 3: Assemble Center Frame Tube with Hole (Yellow) - Left (T1) & Right (T2)
with Climber Support (Silver) - Left (V1)& Right (W1)
3-1. Slide the Center Frame Tube with Hole (Yellow) - Left (T1) & Right (T2) x 1 into Hexagon
Mat (X) and fasten Climber Support (Silver) - Left (V1) & Right (W1) x 1 together by using
bolt (G) x 1 + spring washer (J) x 1 and domenut (K) x 1.
ASSEMBLY TIPS: Screw Plastic Knobs-(Y) X 6 with bolts loosely in place before
assembling the Center Frame Tube (Yellow)-(T) X 4 to prevent the climber from
collapsing during assembly.
NOTE: Please beware that one end of Center Frame Tube (Yellow) - (T) needs
to be the inside and the other end needs to be the outside when assembling.
outside
inside
outside
hole
hole
page 13 of 19
3-2. Slide the rest of Center Frame Tube (Yellow) - (T) x 4 into Hexagon Mat (X) and fasten with
Climber Bend Support (Silver)-Left (V) and right (W) together by using bolt (G) x 5 +
spring washer (J) x 5 and domenut (K) x 5.
Assembly Tip: Do not slide all 4 Center Frame Tubes (Yellow) - (T) into the Hexagon Mat
all at the same time. Slide the Center Frame Tube (Yellow)-(T) in one by one: slide one
Center Frame Tube (Yellow)- (T), fasten, then slide the second one in, fasten, so on.
Assembly Tip: Remove Plastic Knob (Y) and bolt (H) that is immediatedly above the
Center Frame Tube (Yellow)-(T) that is being fastened. To prevent the climber from
collapsing, do not remove the plastic knobs all at once
NOTE: Please beware that one end of Center Frame Tube (Yellow) - (T) needs
to be the inside and the other end needs to be the outside when assembling.
CORRECT INCORRECT
NOTE: Please make sure one end of Center Frame Tube (Yellow) lines up
with other one.
inside
outside
outside
inside
page 14 of 19
Step 4: Place Top Frame Tube (Pink) - (S) onto Climber Bend Support (Silver)
4-1. Place Top Frame Tube (Pink) - (S) x 5 onto Climber Bend Support (Silver) and fasten
bolt(H) x 4 with plastic knob (Y) x 4 together. (See figure below)
Step 5: Insert the Handrail Tube (O) into Wavy Slide Chute (N)
5-1. Position the Handrail Tube (O) correctly.
NOTE: This side is to connect to 6ft slide.
page 15 of 19
5-2. Using bolt (C) x 2 + washer (D) x 2 + spring washer (E) x 2 and domenut (F) x 2 to fasten
Wavy Slide Chute (N) and Handrail Tube (O) together.
Step 6: Assemble the Tie Bar (R)
6-1. Attach the Tie Bar (R) to Bottom Frame Tube with Hole (blue)- (U1) by using bolt (B) x 1 +
washer (D) x 1 + spring washer (E) x 1 and domenut (F) x 1.
Attach the Bottom Chute Support Tube (P) with Tie Bar (R) by using bolt (C) x 1+
washer (D) x 1 + spring washer (E) x 1 and domenut (F) x 1.
P
R
page 16 of 19
Step 7: Place Handrail Tube (O) onto Center Frame Tube with
Step 8: Assemble Top Frame Tube (Pink) - Left (S1) & Right (S2) and
Handrail Tube (O) together on Center Frame Tube with
8-1. Attach Top Frame Tube (Pink) - Left (S1) & Right (S2) and Handrail Tube (O) together on
Center Frame Tube with Hole (Yellow) - Left (T1) & Right (T2) by using bolt (C) x 2 and
domenut (F) x 2.
Hole (Yellow) - Left (T1) & Right (T2)
Hole (Yellow) - Left (T1) & Right (T2)
page 17 of 19
Step 9: Assemble the Bottom Chute Support Tube (P)
9-1. Attach slide chute to the Bottom Chute Support Tube (P) through bottom sided holes on slide
chute by using bolt (A) x 2.
9-2. Fasten bolt (H) x 2 with plastic Knob (Y) x 2 on Top Frame Tube (Pink) - Left (S1) &
Right (S2).
Step 10: Assemble the Ground Anchors (Z)
10-1. Secure each of the Bottom Frame Tube (Blue) to the ground by using Ground Anchor (Z) x 6.
STEP 9-2
STEP 9-1
page 18 of 19
CARE & MAINTENANCE
To clean the equipment, simply wipe with a damp cloth.
Regularly check to see if all parts are tightened and completely secure.
Replace worn and damaged parts when/if found and if necessary, refrain from use until replacement parts
can be obtained.
If the paint is chipped, we recommend you lightly rub the damaged area and cover using a non-toxic enamel paint.
IMPORTANT: While no regular maintenance is required, you must inspect the equipment before each use and
replace any worn, defective, or missing parts. The following conditions could represent potential hazards:
missing, improperly positioned, or insecurely attached bolts. Stop using equipment immediately and guard against
unauthorized use until Dome Climber is properly repaired.
FREQUENTLY ASKED QUESTIONS
Question: “How should I clean my dome climber?”
Answer: You should clean the dome climber with a solution of warm water and non- corrosive/abrasive soap.
Dampen rag with this solution and wipe completely dry before using
Question: “Is there any maintenance I need to do for my dome climber?”
Answer: You should always double check to make sure all your bolts are tight and secure, and that the ground anchors
are present and securely in place before use.
Question: “Something was missing from the packaging,” “I need to purchase a replacement part” or “
I discovered a damaged piece. What should I do?”
Answer: Contact Platports®. You must have proof of purchase and/ or order confirmation available
to be considered for warranty replacement. You must report missing pieces
within 30 Days from date of purchase.
page 19 of 19