SLEEPING - Hülsta...4 E 5.2018 Schlafen: CITADA 3 4 Labelling in type list drawings / assembly...

www.huelsta.com

5/18Type list

SLEEPING

E

2Schlafen: CITADAE 5.2018

NEW range

CITADA

Ancillary units• Wall consoles and consoles in two widths• Top panels in two widths, with optional LED lamp• Chests in two widths• Angled shelves in three widths, with optional LED lamp• Drawer frames in standard grey

WardrobesHinge-door wardrobes according to the endless assembly principle• With plain doors, with optional mirror or with wooden accent in knotted oak or knotted core walnut• With optional all-round passepartout• With optional top LED lamp (12 V; 2.4 W)• With optional handle or strap handle• Wardrobe interior carcase and wardrobe interior fittings in standard white lacquer version• Standard interior fittings: 2 fitted shelves. 1 clothes rod• Functional and high-quality wardrobe interior fittings (see „Wardrobe interior fittings“ type list)

Quality features• All wardrobe doors with cushioning system• All wardrobe doors with handle or strap handle and high-grade spring hinges• All metal hinges• Visually unobtrusive 2.5 mm drilled holes for wardrobes• Centre partitions and end side-sections of wardrobes with special plinth adjustment• hülsta-SoftFlow: Drawers of ancillary units on hidden bearings incl. auto pull-in feature with brake• hülsta-MagicClose: All wooden hinge-doors with door cushioning system

Height reductions at intervals of 1.0 cm without surchargeContents

Page

Range introduction, lists of versions, explanation of versions 2-4

Special combinations 6-7

Hinge-door wardrobes 8-9

Beds, bed accessories 10

Ancillary units, angled shelves, remote control 11-12

General information:

Special-sized products, special articles 13

Usable bed inside height and space under bed 14

Important notes: quality of walls / assembly instruction 15

Natural meets modern. CITADA gives the bedroom clear, flowing contours with its combi-nation of natural wood and fine lacquers. Typical of hülsta: besides intricate craftsmanlike details, CITADA also provides loads of comfort – from the convenient sleep surface height to the functional wardrobe. The folded look is continued throughout the range – from the bed to the ancillary units and from the headboard to the drawer front gently encompassing the units.

Beds• Beds with headboard in wood/lacquer version in three lengths and four widths; head- and footboard accent

in wooden version• Bed accessories: headboard accent in artificial leather version, metal arched support in matt chrome

Range introduction

In combination with the hülsta Sleeping System, the beds guarantee highest sleeping comfort. With its high-quality spring base frames and mattresses, the hülsta Sleeping System provides the perfect prerequisites for relaxing sleep (see “SLEEPING SYSTEMS“ type list).

Link to the assembly / user instruction movies

CITADA

3E 5.2018Schlafen: CITADA

693694

Wooden accent top drawer

Knotted oakKnotted core walnut

Model no.

693694

Head- and footboard accent


Model no.

693694

Model no. Wooden accent hinge-door


Range introduction

693694

648663

Wardrobe outside carcase and front

WardrobesPassepartout


Pure white lacquerSilk grey lacquer

Model no. Model no.

Wardrobe inside carcase in standard white lacquer

648663693694

Headboard, bed sides and lower footboard

Beds

Pure white lacquerSilk grey lacquerKnotted oakKnotted core walnut

Model no.

S452S453S454

Headboard accent

Artificial leather dark brownArtificial leather taupeArtificial leather anthracite

Model no.

648663

Carcase and front

Consoles, wall consoles, chests

Pure white lacquerSilk grey lacquer

Model no.

Handle versionsCITADA provides two different handles. If no further details are stated in the order, handle 061 is supplied. Please state clearly in the order!

Matt chromeHandle 061

Lists of versions

100% leather brown / matt chromeStrap handle 062

Dark grey shading in drawings = Components in wooden version with cracks




34

Labelling in type list drawings / assembly notes for wall unitsThe majority of units have two wall mounting points (= number of base plates), if these are to be fitted as wall units. This is not explicitly mentioned in the type list. If a different number of wall mounting points (= base plates) is required, this is marked in the drawings in the type list with numbers in black boxes. Please be sure to note here the information and notes in the “Wall composition” chapter!

Notes on delivery:The majority of the units are delivered standard as fully connected units (glued) so that the carcase cannot be disassembled. There are however some excep-tions to this rule:

Some carcases are delivered as complete units but can be disassembled into individual sections in the final customer’s home. These types are marked with a 1 in the type list.

Some carcases are delivered in individual sections because of their size. These types are marked with a 2 in the type list.

The fronts with the number 2 are delivered separately and can therefore always be (dis-) assembled.

1

2

Labelling in type list drawings / assembly notes for wall units Notes on delivery

Important notes: Generally speaking, you as a dealer/qualified fitter are responsible for the correct wall mounting of the units. That is why wall mounting should only be carried out by properly trained and qualified fitters. hülsta supplies materials for mounting units on walls for nearly all the units and which should be used for safety and for constructional reasons. The assembly materials supplied by hülsta (plugs, screws) are only suitable for fitting components on to concrete in firmness class C12/15.For other materials (please see separate materials table in the wall composition chapter) we provide you with an assembly mortar set as an extra order. Please note that this assembly mortar set is also only suitable for the materials listed in the materials table. If walls are made up of other materials (e.g. plastered or lighter wall materials), one should use another method of mounting better suited to the load on site. Please note that if the units are not mounted properly on the wall, there is a risk of the units falling down or tipping over – especially when alternative mounting materials acquired on site have been used.For the reasons stated above it is absolutely essential to enquire about the composition of any walls before signing any contracts.

Wall fitting

Explanation of versions

Surface versions of components in wooden versions without cracks for:Passepartout, headboard, bed sides, lower footboard

Surface versions of components in wooden versions with cracks for:Wooden accent hinge-door, head- and footboard accent, wooden accent top drawer

Range introduction


CITADA


Possible arrangements


Surcharge for passepartout

Special-sized products for special combinations are possible! Pricing: special combination + 15%

plus all the required special-sized products (see „Special-sized products“)!

Please note: Height reductions of wardrobes remain free of charge!

Special combinations consisting of a bed unit (bed and two wall consoles) and a hinge-door wardrobe. The price of an entire special combination (bed unit and wardrobe) can be found in the grey shaded boxes!

4-door hinge-door wardrobe202 cm wide

Important: Choose a bed (all bed sizes possible – please state type number; see page 10), two consoles (wall consoles types 5001 and 5011 possible – please state type number; see page 11) as well as one of the wardrobes listed below.

5-door hinge-door wardrobe(centre door with right hinges)252 cm wide

6-door hinge-door wardrobe302 cm wide

Surcharge for wardrobe lamps

Information on the energy class: see

page 8!

2x

2x

For this wardrobe combination we recommend 2 top LED lamps.

3x

3x

Special combinations

Price of an entire special combinati-on (bed unit and wardrobe)

with hinge-doors

3x

3x

-

A8406

-

A8416

-

A8436

-

301

-

303

-

304

-

394

-

394

-

394

Special combinations are arrangements that are reduced in price. This price advantage is only available when the arrangement is ordered exactly as described. The special combi-nations can be enhanced by including accessories. These are charged extra.

Please also note the mattresses and base frames in the “Sleeping systems” type list!

Bed unit with wall consoles




CITADA


Surcharge for wooden accentEach wardrobe door can be optionally fitted with a wooden accent in knotted oak or knotted core walnut, for which a surcharge is made.

Bed headboardStandard version: headboard accent in wooden version (as in illustration 1)

ConsolesStandard version: wall consoles (as in illustration 1)

Surcharge for mirrorEach wardrobe door (exception: doors with wooden accent) can be optionally fitted with a mirror (vertical facette), for which a surcharge is made.

=

=

=

Remote control

Surcharge for remote control(transmitter + receiver) type

Surcharge for extra transmitter type

Surcharge for extra receiver type

=

Top LED lamp

Surcharge for each additional lamp type

Surcharge for headboard accent in artificial leather version

(as in illustration 2)

Bed legsStandard version: bed on round bed legs (as in illustration 1)

Surcharge for metal arched support(as in illustration 2)

Surcharge for floor consoles(as in illustration 2); surcharge per console:

--

-

3003

-

3002

-

2001

-1601

-1602

-1603

-394

Illustr. 1 Illustr. 2


Additional fittings for special combinations / surcharges / lamps

This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V

Surcharge for mirror per hinge-doorSurcharge for wooden accent per hinge-door

Additional fittings for wardrobes

Additional fittings for consoles

Additional fittings for beds




Notes on planning hinge-door wardrobes according to the endless assembly principle

Hinge-door wardrobes can be planned endlessly and combined with one another. Due to the various element widths one can create many total wardrobe widths. In this way the available floor space can be exploited to the full. For each wardrobe combination, the first element on the left is considered to be the basic unit, incorporating both outer side-sec-tions. One can only include one basic unit in each combination. When adding on extension units, the right-hand side-section of the basic unit is employed as the end side-section of the complete combination. In the case of single-door hinge-door units one can choose between left- and right-hand hinges. The graphics shown below give you an excerpt from our wardrobe assortment.

Standard interior fittings per unit: 2 fitted shelves, 1 clothes rod. All interior surfaces are in white lacquer.

Hinge-door wardrobe

• Hinge-door wardrobes can be planned endlessly and combined with one another

• Front mirrors and wooden accent hinge-door available at a surcharge• Unit outside widths:

52, 102 cm (basic units) 50, 100 cm (extension units)

• Unit inside widths: 48, 98 cm• Outside depth: 61.0 cm• Inside depth: 56 cm• Door opening angle: approx. 94°

Examples of wardrobes

For calculating the total width when fitting a passepartout, please note the protrusion of 3.1 cm left and right!

Hinge-door wardrobes

LampsAll hinge-door wardrobes are available with top LED lamps. One top LED lamp is fitted standard above each element – 1 or 2 door – 12 V; 2.4 W. If required, a top LED lamp can be fitted centrally above each door. Please include a sketch in all cases.Switching is done by an external footswitch. A remote control unit is also available as an alternative, which is charged extra. The remote control unit incorporates one transmitter and one receiver which operate all the LED lamps. The footswitch is omitted when the remote control unit is employed.

without passepartout

Heights: 229.6 cm 233.9 cm

see page 9Widths:

Depths:

Dimensions

Height reductions of hinge-door wardrobes at intervals of 1.0 cm without surcharge

with passepartout

61.0 cm 61.6 cm

234.6 cm

with top LED lamp

69.0 cm

238.9 cm

with passepartout and top LED lamp

69.0 cm

=

=

=

Remote control




=

Top LED lamp

Surcharge for each additional lamp type

-1601

-1602

-1603

-394


CITADA


Surcharge for mirror

Each wardrobe door (exception: doors

with wooden accent) can be optionally

fitted with a mirror (vertical facette), for which a surcharge

is made.

Surcharge for top LED lamp

1 lamp per unit

Surcharge for passepartout

Surcharge for wooden accent

Each wardrobe door can be

optionally fitted with a wooden

accent in knotted oak or knotted core walnut, for which a surcharge is made.

Surcharge for wooden accent per hinge-door:

Surcharge for mirror per hinge-door:

Please mark exactly in the front sketch or state in the order (from the left), which hinge-doors are to be fitted with a wooden accent.

Please mark exactly in the front sketch or state in the order (from the left), which hinge-doors are to be fitted with a mirror.

L/R = Door hinge left/right

Single-door unit,left or right,52 cm wide

Twin-door unit,102 cm wide

Single-door unit,left or right,50 cm wide

Twin-door unit,100 cm wide

Extension units with 1 centre partition (2 cm thick)

For each project please remember to leave a 2 cm gap to the ceiling and at the side for assembly!

Basic units with 2 outer side-sections (each 2 cm thick)

For each wardrobe combination, the first element on the left is considered to be the basic unit, incorporating both outer side-sections. One can only include one basic unit in each combination. When adding on extension units, the right-hand side-section is employed as the end side-section.

Doors

L

L


Height: 229.6 cm (heights with passepartout and/or top LED lamp: see table on page 8); height reductions in intervals of 1.0 cm without surcharge

Width: see table (widths with passepartout: + 3.1 cm each side)

Depth: 61.0 cm (depths with passepartout and/or top LED lamp: see table page 8)

Interior fittings per unit: 2 fitted shelves, 1 clothes rod; interior fittings always in white lacquer.

61,0

61,0

61,0

61,0

-

A2012 RA2011 L

-

A202

-

A0012 RA0011 L

-

A002

-

342

-

344

-

347

-

349

-

394

-

394

-

394

-

394

--


Please also note the functional and high-quality wardrobe interior fittings in the „War-drobe interior fittings“ type list as well as the special articles and possible special-sized products.

The surcharge for the passepartout frame of the basic units includes the left- and right-hand vertical frame as well as the horizontal frame, the surcharge for the extension units only includes the horizontal frame. When adding on extension units, the right-hand frame of the passepartout of the basic unit is employed as the end unit of the complete wardrobe.

Information on the energy

class: see page 8!


Please also note the mattresses and base frames in the “Sleeping systems” type list!Beds

149.2 x 208.3169.2 x 208.3189.2 x 208.3209.2 x 208.3

Beds with headboard in wood/lacquer version; head- and footboard accent in wood versionBeds incl. support slats for base frames and mattresses• Adjustable in height by 3.2 cm downwards and upwards• Usable bed inside height: max. 18.2 cm

Please state all the versions clearly in the order!

Type no.Inside dims.(in cm)

140 x 200160 x 200180 x 200200 x 200

140 x 210160 x 210180 x 210200 x 210

140 x 220160 x 220180 x 220200 x 220

Outside dims.(in cm)

149.2 x 218.3169.2 x 218.3189.2 x 218.3209.2 x 218.3

149.2 x 228.3169.2 x 228.3189.2 x 228.3209.2 x 228.3

Bed accessories

Surcharge for arched supportThe beds normally stand on round legs. They are also available optionally on a metal arched support with a hovering look at a surcharge. Please state clearly in the order!

Bed on legs in matt chrome (standard) Bed on metal arched support in matt chrome

Bed sizes:Headboard height: 100.3 cmHeight of top rim of bed side: 46.7 cmSpace to floor: 20.5 cmMaximum usable bed inside height (when support slats in bottom position): 18.2 cm

Surcharge for headboard accent in artificial leather versionThe headboard accent is optionally available in an artificial leather version against surcharge. Please state clearly in the order!

Headboard accent in wooden version (standard) Headboard accent in artificial leather version

625626627628

----

635636637638

----

645646647648

----

-

3003

-

3002

Headboard accent

Footboard accent


CITADA



LED lamp for top panels

for 70.4 cm widthfor 52.8 cm width

1.9 W 2.6 W

Wall consolesWall consoles18.8 cm high,45.0 cm deep

Drawer in wooden accent

52.8 cm wide

1 drawer

70.4 cm wide

1 drawer

Max. load: 15 kg

Top panelsTop panels35.2 cm high,3.8 cm thick incl. assembly space

70.4 cm wide52.8 cm wide

52.8 cm wide

2 drawers

70.4 cm wide

2 drawers

Wall bracket If consoles are to be included as wall consoles, a wall bracket must be ordered. In this case the plinth adjusters are omitted.

ConsolesConsoles45.2 cm high (47.0 cm high incl. 1.8 cm high plinth adjusters),45.0 cm deep

Top drawer in wooden accent

LED lamp for top panels

Switch in panel, 17.6 cm from top rim and 2.0 cm from the outer side of the panel

Please state clearly in the order whether the unit is to be fitted on the left or right-hand side.

The wall consoles may only be fitted on absolutely solid walls. Gypsum or other light masonry is not suitable for this purpose. Please be sure to note here the information and notes in the “Wall composition” chapter!

-

5001

-

5011

-

5002

-

5012

-

5003

-

5013

-

5051

-

5071

-

4528

-

4705

The top panels may only be fitted on absolutely solid walls. Gypsum or other light masonry is not suitable for this purpose. Please be sure to note here the information and notes in the “Wall composition” chapter!

Charger for consolesØ 6.8 cm, incl. lead and mains plug;12 V, 1000 mA current, inductive charging 5 W, Qi compatible

The charger is stored invisibly between the cover shelf and the carcase (can not be fitted later) and enables cable-free charging of devices (like smart phones) with induction batteries.

-

7620

Charger for consoles: see above

Charger for consoles


ChestsChests71.6 cm high (73.4 cm high incl. 1.8 cm high plinth adjusters),45.0 cm deep

Top drawer in wooden accent

105.6 cm wide

3 drawers

123.2 cm wide

1 door; 3 drawers

Angled shelvesAngled shelves19.2 cm high19.7 cm deep

for fitting anywhere on walls

LED lamp for angled shelves: see below!

50 cm wide 70 cm wide 120 cm wide

Wall bracket If chests are to be included as wall chests, a wall bracket must be ordered. In this case the plinth adjusters are omitted.

as illustr.v. versa

This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V LED lamps incl. footswitch. A remote control unit is possible for operation (against a surcharge).

LED lamp for angled shelves

for 50 cm width for 70 cm width for 120 cm width

LED lamp for angled shelves

Switching is done by an external footswitch. A remote control unit is also available as an alternative, which is charged extra. The remote control unit incorporates one transmitter and one receiver which operate all the LED lamps. The footswitch is omitted when the remote control unit is employed.

Remote control

-

4700

-

41241124124111

-

4105

-

4123

-

501

-

502

-

503

-

550

-

570

-

5100

Max. load: 15 kg

The angled shelves may only be fitted on absolutely solid walls. Gypsum or other light masonry is not suitable for this purpose. Please be sure to note here the information and notes in the “Wall composition” chapter!

Assembly notes for wall units:Please be sure to note here the information and notes in the “Wall composition” chapter!

3

3


=

=

=

Remote control




-1601

-1602

-1603

CITADA


Special-sized products

Special articles

Edge veneerfor veneered/lacquered versions per m. length

165° hingesWardrobe doors can also be fitted with 165° hinges against a surcharge (only possible on plain, straight hinge-doors; impossible on fabric-covered doors and accent fronts MADERA). Please mark the doors clearly in the order!

Surcharge for 165° hinges per hinge-door:

Panels for side and top covering of fitted wardrobes (not possible for high- gloss versions; support construction and fitting materials must be acquired on site).

For veneered/lacquered versions (max. 268.0 cm long, max. 59.0 cm wide, 2.0 cm thick)Basis charge per order:+ price per m² - lacquer+ price per m² - veneerVeneer match with fronts can not be guaranteed.

Wardrobe doors are also available as separate units and are charged as follows:

For 1 hinge-door/folding-door wing: 50% of the concerning 1-door hinge-door extension unit

For 1 sliding-door including mechanism: 35% of the twin-door sliding-door wardrobe

For door superstructures, type 100 (max. 98 cm wide, only for assembly between wardrobes): 100% of twin-door hinge-door extension unit

Wardrobes

Special heights:Hinge-door - WoodHinge-door - Mirror

Special depths:Surcharge per unit

When ordering extra fitted shelvesSize reduction surcharge per fitted shelf

Side sloping:Surcharge per unit without passepartout in the slopeSurcharge per unit with passepartout in the slope

Rear sloping:Surcharge per unit

Beds

Bed in special length 190 cm

Special-sized products for special combinations:Pricing: special combination + 15% plus all the required special-sized products (see above)

More special products are possible. Please get in touch with your customer advisor.

CITADA

without surchargewithout surcharge

Special colours; Note on „Blue Angel“ / Emissions label of DGM

Special coloursAll the hülsta lacquer colours are possible for nearly all the hülsta ranges. Availability and prices on request.

Note on „Blue Angel“ (RAL-UZ 38) and Emissions label of DGM (Class A)It is possible that the requirements of the „Blue Angel“ and the DGM Emissions Label can-not be met by some of the lacquer colours in price groups II and III (see here the different lacquer versions in the NURIA range), depending on the colour mix (surface ratio of these colours in the corresponding order). However, the legal requirements are definitely met in all cases!

Individual special-sized productsIf the special-sized product that you require is so unusual that it cannot be illustrated with the many special sized products that we already provide and charge for, then we will quote you the price using a HK unit type factor. In your order please state for us the relevant enquiry number and the HK unit type factor stated.

000300031

-0007

-9993

-9994

-99912

-99964

-9901--

990990

-9902

-180

-HK

-99916


Note on usable bed inside height:The support slats of the hülsta beds are delivered in the centre position, i.e. they can be adjusted by 3.2 cm upwards and downwards (exception: for LUNIS beds in the standard surface height 1 only by 3.2 cm upwards). If the slats are set in the lowest position, the maximum usable bed inside height is achieved. In the case of some beds, the bed inside height is comparatively low. This means that mattresses in combination with base frames that are somewhat higher are not held so well by the bed side sections. Please note that the usable bed inside height of beds with height adjustable support slats is reduced when these are set higher.

This is how to calculate the individual height from the data supplied with the base frames:

Note on space under bed:The storage space underneath the base frame is calculated from the bed height minus the usable bed inside height.

Example bed: 42.2 cm - 18.0 cm = 24.2 cm.

Max. usable bed inside height:18.0 cm

approx. 12.5 cm for holding mattress

5.5 cm total height of base frame (example: hülstaflex basic B)

Example (for all beds): bed and hülstaflex basic B base frame (back and foot sections adjustable)

Usable bed inside height and space under bed

{

LUNIS bed in standard surface height 1 and hülstaflex basic B base frame (back and foot sections adjustable)

Max. usable bed inside height:14.0 cm

approx. 8.5 cm for holding mattress

5.5 cm total height of base frame (example: hülstaflex basic B)

{

CITADA


-

M2

Labelling in type list drawings / assembly notes for wall unitsThe majority of units have two wall mounting points (= number of support boards), if these are to be fitted as wall units. This is not explicitly mentioned in the type list. If a diffe-rent number of wall mounting points (= support boards) is required, this is marked in the drawings in the type list with numbers in black boxes. Every support board requires four mounting screws.

One assembly mortar set is sufficient for up to a maximum of 3 support boards or 4 wall side-panels.

Important note: Depending on the composition of the wall (see wall types illustrated above), assembly must be carried out using the special assembly mortar set and a standard trade mastic tool which are the basic essentials for safe and clean workmanship.

Wall composition / assembly instructionImportant notes:The composition of walls must be ascertained before concluding a contract and be checked by a qualified fitter before assembly takes place.

Assembly may only be carried out by a qualified fitter under careful observation of the assembly instructions.

The plastic Rawl plugs with the type name SX 8 x 65 from the Fischer Company supplied by hülsta as a standard set are only suitable for concrete ≥ C12/15, if the wall composi-tion and compression strength corresponds to the table below. Under no circumstances must a unit be assembled on light masonry.

Furthermore, we provide a mounting set with assembly mortar from the Fischer Company for the types of walls listed below (see assembly mortar set below). Again, assembly must be carried out by a qualified fitter under careful observation of the wall composition and assembly instruction. The compression strength levels stated below must be met under all circumstances.

Assembly mortar set for up to a maximum of 3 support boards consisting of:

9x injection retaining sleeve9x screw-in sleeve1x injection cartridge2x static mixer1x assembly instructions

Please use the mounting screws from the standard set (supplied free of charge).

Mounting sets

Standard setThe standard set consists of 4 plastic Rawl plugs (SX 8 x 65) and 4 mounting screws and is sufficient for 1 support board. The standard sets are included in the packet of fittings to match the number of support boards.

A different and more suitable type of mounting must be chosen by a qualified fitter in all other cases. hülsta cannot accept any responsibility for the choice of any other types of mounting! Please note that if the units are not mounted properly on the wall, there is a risk of the units falling down or tipping over – especially when alternative mounting materials acquired on site have been used. Generally speaking, you as a dealer/qualified fitter are responsible for the correct wall mounting of the units.

34

= 3 support boards= 4 support boards, etc.

Building bricks Mz 12Compression strength ≥ 12 N/mm²

Limestone blocks KS 12Compression strength ≥ 12 N/mm²

Perforated sand lime bricks KSL12Compression strength ≥ 12 N/mm²

Vertically perforated bricks HLz 12Compression strength ≥ 12 N/mm²Bulk density ≥ 1.0 kg/dm³

Concrete C12/15Compression strength ≥ 15 N/mm²

Assembly mortar set only suitable for the materials stated below!Standard set (SX 8 x 65)

Solid blocks of light concrete V2Compression strength ≥ 2 N/mm²

Perforated blocks of light concrete Hbl 2Compression strength ≥ 2 N/mm²

Aerated concrete PP2Compression strength ≥ 2 N/mm²

Materials tablewith a description of which sets are to be used with the following types of walls:

Example of order:

• Add up number of support boards for all existing unit types

• Divide the sum by “3”

• Round up the result to a full number

= Number of assembly mortar sets required

Important notes

Design and concept legally protected, subject to error and alterations to construction, colour and materials by way of technological progress.

Stand:

hülsta CITADA

Your Hotline to hülsta

Lots to do? A customer wants his project finished and you haven’t got enough time? Or the project is so complex that it will take too much time?

This is exactly the kind of situation we created the hülsta Planning Service for. hülsta’s employees create the required project for you at short notice. Based on your information, we implement the project perfectly with all views and a complete order list ready for immediate forwarding to the customer.

The hülsta check list (available at https://hulsta.com/de/service/showroom/) makes it all really easy for you. You won’t forget anything with this list and the customer receives a project he will be thrilled about as quickly as possible.

Our Saturday hotline is available all day from 10.00 a.m. until 6.00 p.m.

Telephone: +49 (0) 2563 / 86-1800

On working days the hülsta Sales Department is available all day from 8.00 a.m. until 6.00 p.m.

hülsta Planning Service

Special wishes? Come to us!

We are open Saturdays for you, too!

E 5.2018

Maximum individuality! – Maximal flexibility! – hülsta makes most of your special wishes possible.And if you do have a wish which is not quite so easy to implement, just give us a call or send us a mail or a fax. We have our own hülsta “Special Wishes Team” who are there to help you realise just these customer requests. These colleagues are professionals when it comes to special products. They plan and calculate the products possible for you and even develop an alternative suggestion if the idea should turn out to be technically impossible.

Here is an overview of the hülsta range of special wishes:• A lot of special products can be ordered simply via the type list• Special-sized products are planned simply and professionally• Competent colleagues advise you by phone, by fax and by mail• You will be sent alternative suggestions if the idea is technically impossible• Many special-sized products are available without a surcharge• Specially qualified carpenters and technicians implement your plans perfectly

Do you have any questions or require any alterations to your order confirmation?Do you have any questions on our products or your current order?Do you have any complaints about supplied goods or required replacement parts?Contact Telephone: +49 (0) 2563 / 86-1144 • email: [email protected]

Do you have any questions, suggestions or wishes for the hülsta Marketing team or the hülsta product seminars?Contact Telephone: +49 (0) 2563 / 86-1611 • email: [email protected]

hülsta Planning ServiceTel.: +49 (0) 2563 / 86-0

Fax: +49 (0) 2563 / 86-2666Mail: [email protected] from 8.00 a.m. until 6.00 p.m.

hülsta Special Wishes TeamTel.: +49 (0) 2563 / 86-0

Fax: +49 (0) 2563 / 86-1417Mail: [email protected]

hülsta-werke · Karl-Hüls-Straße 1 · D-48703 StadtlohnTel. +49 (0) 2563 / 86-0 · Fax +49 (0) 2563 / 86-1000

www.huelsta.com

SLEEPING - Hülsta...4 E 5.2018 Schlafen: CITADA 3 4 Labelling in type list drawings / assembly...

Documents

Transcript of SLEEPING - Hülsta...4 E 5.2018 Schlafen: CITADA 3 4 Labelling in type list drawings / assembly...