SL100 & SL200 Super Lift Hydraulic Gantry
Transcript of SL100 & SL200 Super Lift Hydraulic Gantry
EMPOWERING YOUR SUCCESS
SL100 & SL200
Super Lift
Hydraulic Gantry
PRODUCT OVERVIEW SL100 and SL200 Hydraulic Gantry
SL100 & SL200 Overview
Latest addition to Enerpac TelescopicHydraulic Gantry portfolio
Customer demand to have a highercapacity gantry on a narrow 2ft. trackgage
Standardize on industry accepted 2ft.track gage
Increase value over existing SL60 &SL125 models
– Upgrade to 2ft track gage– Increased capacity in first stage
Standardization of components such asbase frames
Compatible with existing gantryaccessories
Alignment of model numbernomenclature
Positioned to allow future smaller gantryoffering
Complies to industry standards
Why use a Hydraulic Gantry?
Alternative lifting solutionto mobile cranes– Lower cost of ownership,
i.e.: Initial investment,transportation cost and labor
– Avoid onerous crane usagelegislation
– Easy to mobilize anddemobilize
High lifting capacity andaccurate load positioning
Ability to operate inconfined or limited accessspaces
MARKETS AND APPLICATIONS
SL100 and SL200 Hydraulic Gantry
Markets & Applications
Primary market focus• Power generation
– Nuclear
– Fossil fuel
– Renewable (Wind)
• Oil & Gas
– Petrochem and refinery
• Industrial
– Heavy manufacturing
– Metal production
• Civil construction
– Bridges
Common applications involve transportation (local) &
installation of:– generator, transformer, compressor, module, vessel, tank heavy
plant/machine, press, bridge decks
Manufacturing
Machinery Moving
Rail
Power Generation Material Handling
Rail Car Maintenance Vessel Placement
O&G
Container Off Loading Generator Placement
Markets & Applications
Bridge Construction
Deck Placement
PRODUCT & ACCESSORIES SL100 & SL200 Hydraulic Gantry
Hydraulic Gantry Portfolio
SL200 SL100
Super Lift Gantries
Range from 60 to 400 ton
Self contained hydraulics
Bare cylinders
Self propelled wheels
2 or 3 stage lift cylinders, depending
on model
Intellilift control system
Up to 9 m (30 ft.) height
ASME B30.1 compliant
SL200
SL100
SL100 Specifications
SL200 Specifications
Typical Gantry Application
A. Hydraulic Gantry
B. Header Beams
– Several lengths available
C. Side Shift or Lifting Lugs
D. Skid Tracks
– Customer MUST use skid tracks to
ensure perfect alignment and for load
distribution
E. Slings (accessory from Enerpac)
F. Shackles (accessory from Enerpac)
G. Proper leveling material to level the
skid tracks (outside our scope)
H. Electrical Cords (outside our scope)
I. Power Source (outside our scope)
ADDITIONAL COMPONENTS & ACCESSORIES
SL100 & SL200 Hydraulic Gantry
Header Beams
Available Lengths
– 6m, 8m, 10m, 12m
Load charts provided for
all header beams
Can use any standard
Enerpac header beams
Custom lengths available
Sold in pairs
How to read load charts
Load chart SL100
This table must always be used for side shift operations. During this kind of work, the load's
center of gravity (COG) shifts from one point to another. After this kind of shift, one or two
units will bear more of the load, and the other two will bear less of it. In order to ensure that
the maximum permissible load is not exceeded for any of the units, it is necessary to
consult the table before each operation.
Load chart SL200
This table must always be used for side shift operations. During this kind of work, the load's
center of gravity (COG) shifts from one point to another. After this kind of shift, one or two
units will bear more of the load, and the other two will bear less of it. In order to ensure that
the maximum permissible load is not exceeded for any of the units, it is necessary to
consult the table before each operation.
Lifting Anchor & Side Shifts
Lifting lugs are mechanicallinks for lifting loads– They are positioned manually
Side shift is a mechanicallink combined with anelectric drive to shift theload along the header beam
Both are sold in sets of 4
Sized based on capacityand header beamdimensions.
Recommended sizes for theSL100 & SL200:– Side Shift: BSSBL300
– Lifting Anchor: LLSBL125
BSSBL300 Side Shift
SL Series Skid Tracks
Sold in 3m & 6m sections– Customer MUST use skid tracks
to reduce ground bearing
pressure and to align the gantries
during traveling
– Angled bolted joint for smooth
transition
Most critical component
when setting up a gantry
High capacity gantry on 2ft
track
Models:
– STSL300-3
– STSL300-6
Accessories
Tarpaulin Covers
Transport frame for
side shift units
Slings (endless
grommet) according to
EN 13414-3
Shackles Green Pin
SAFETY & CONTROLS SL100 & SL200 Hydraulic Gantry
Safety
Factors that can contribute to unsafe operation - not exhaustive:
Operation by unqualified or unapproved personnel
Operation above rated capacity
Rigging attachment to gantry and load misalignment
Un-synchronous lifting
Lifting with less than 4 lifting units
Asymmetrical positioning alignment of load
Unsuitable or insufficient ground works / foundations
Skid-tracks, not straight, parallel, level, securely-joined,continuous without gaps
Wind shear
Addition to an elevated load
Insufficient maintenance & inspection program
Controls
Intellilift control system
– Wireless control on complete
range of gantries
– Unrestricted operator position
– Automatic synchronization for
lifting/lowering AND travelling
– Load and Stroke readouts
– Controls electric side shift
– Can be wired if wireless is not
permitted
Manual controls at each leg
Manual Controls
Wireless Controls
Testing
Each gantry is tested under witness of Lloyd’s Register
Gantries are tested at maximum capacity at maximum
extension.
Customers are invited to witness this F.A.T.
Commitment To Quality
Witnessed to
125% of maximum
working load at full
extension
Actuant LEAD
Continuous
Improvement
Methodology
ISO 9001:2008
Registered
TUV-SUD Testing
and Compliance
CE Certification
Meets ASME
B30.1-2015