Sketcher CATIA
Transcript of Sketcher CATIA
-
8/12/2019 Sketcher CATIA
1/23
CATIA TUTORIAL
SKETCHER
-
8/12/2019 Sketcher CATIA
2/23
We are going to sketch the
following:
-
8/12/2019 Sketcher CATIA
3/23
1. Go to Start Mechanical Design Sketches.
2. Select a plane. (Click on the XY plane).
-
8/12/2019 Sketcher CATIA
4/23
3. Click on this icon to create a rectangle.4. Next, put the dimension as below using the
constraint icon .
-
8/12/2019 Sketcher CATIA
5/23
5. Double click at the dimensions. Put in the following:
length along x axis 120, length along y axis 163.
-
8/12/2019 Sketcher CATIA
6/23
6. Create 4 circles using the circle icon .
7. Modify the dimensions of each of the circles to
be of radius 25, 20, 10 and 10 mm respectively.
-
8/12/2019 Sketcher CATIA
7/23
8. Click on the vertical line. Then press Ctrland click onthe circle (R25).
9. Click constraint define in dialog box . Click on tangent
in the dialog box.
-
8/12/2019 Sketcher CATIA
8/23
10.Repeat the procedure by clicking the horizontal line andthe circle. You should get as the picture below.
11. Repeat the procedure with the R20 circle.
-
8/12/2019 Sketcher CATIA
9/23
12. Add lines into the sketch.
13. Align the lines accordingly with circles.
14. Tangent the lines with the circles where necessary.
-
8/12/2019 Sketcher CATIA
10/23
15. Click on the lines tangential to the circle R25 (use Ctrl),then the constraint icon.
16. Modify the angle to 15 .
17. Repeat the same procedure for the circle R20. Modifythe dimension to be 25 .
-
8/12/2019 Sketcher CATIA
11/23
18. Click on the Quick Trim icon to trim off the
unwanted parts. Your sketch should look like the picture
below once trimming is done.
-
8/12/2019 Sketcher CATIA
12/23
19. Click on the vertical line and the axis to which you wantthe line to coincide with.
20. In the constraint definition dialog box, click on
coincidence.
-
8/12/2019 Sketcher CATIA
13/23
21. Add circles to the sketch as shown. The circle above
should be 15 mm in radius while the circle below should
be 10 mm in radius.
-
8/12/2019 Sketcher CATIA
14/23
22. Make a horizontal line 35 mm from the vertical line.
23. From the end of the line, make a vertical line (the
length of the line to be decided by you.)
24. Trim the 35 mm horizontal line.
-
8/12/2019 Sketcher CATIA
15/23
25. Click on the all remaining parts of the sketch.
-
8/12/2019 Sketcher CATIA
16/23
25. Click on the mirror icon to mirror the image.
26. Click on the coincidence axis when prompted.
-
8/12/2019 Sketcher CATIA
17/23
27. Make a circle at the bottom of the sketch and make aline to tangentially align the circle.
28. Repeat the procedure with another circle on the other
side.
-
8/12/2019 Sketcher CATIA
18/23
29. Trim the necessary elements.
-
8/12/2019 Sketcher CATIA
19/23
30.Find the elongated hole icon and click on it to create anelongated hole as shown.
-
8/12/2019 Sketcher CATIA
20/23
31. Click on the middle line of the sketch and the middleline if the elongated hole
32. Coincide the two lines.
-
8/12/2019 Sketcher CATIA
21/23
33. The elongated hole will move to the middle of the
sketch.
-
8/12/2019 Sketcher CATIA
22/23
FINISH SKETCH TUTORIAL
-
8/12/2019 Sketcher CATIA
23/23
Extra: Try making the following using line, spline and arc
commands.