SKA site spectrum monitoring, measurement program and …...The measurement report code is a...
Transcript of SKA site spectrum monitoring, measurement program and …...The measurement report code is a...
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
SKA site spectrum monitoring,measurement program and data processing
Draft Report
Verified:
Name Signature Date Rev.nr.
... 0.3
Accepted:
R.P. Millenaar R.T. Schilizzi
.................. .................. ..................
date: date: date:
c⃝ASTRON 2011
1
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
Distribution list:
Group: For Information:
Expert Panel on RFI and EMI R.T. Schilizzi
Site Representatives
Document revision:
Revision Date Section Page(s) Modification
0.3
..
July 25, 2011
..
all
..
all
..
creation
..
2
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
Acknowledgements
Thanks to the Site teams for contributions to this report, specifically concerning information on the SKA
2010/2011 spectrum monitoring campaign systems and for their contributions and feedback concerning
the signal processing.
3
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
Contents
1 Introduction 6
1.1 Measurement types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Deviations from the RFI 2008-2011 agreement . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Measurement set-up 8
2.1 Bandwidth and integration time of the modes . . . . . . . . . . . . . . . . . . . . . . . . . 8
3 Measurement programme 10
3.1 Fast Scanning mode (FS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2 High Sensitivity mode (HS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.3 Transient mode (TR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.4 Rural Mode (RM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.5 Max hold Mode (MH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4 Calibration 13
4.1 Gain calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2 Gain smoothing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3 Noise temperature calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4 Power sanity check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.5 Antenna gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.6 Flux calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.7 Transmitter detection and baseline correction . . . . . . . . . . . . . . . . . . . . . . . . . 22
4
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
4.8 Occupancy statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.9 Time statistics and averaged power statistics . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.10 Figure compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5 Output description and measurement result summary 27
5.1 FS mode results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.1.1 Spectrum measurement spectra . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.1.2 Calibration spectra . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.2 HS mode results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.2.1 Spectrum measurement spectra . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.2.2 Calibration spectra . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.3 RM mode results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.4 MH mode results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.5 TM mode results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
References 31
Appendix A. Measurement report list 32
Appendix B. Allocations and services 33
Appendix C. Component calibration data 34
Appendix C1. Antenna, LNA, and noise diode . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Appendix C2. LNA, and noise diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Appendix A2. Cables and switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
1 Introduction
As part of the SKA site selection process the Radio Frequency Interference environment has been mea-
sured at two candidate sites. This was done under the“Agreement on radio frequency interference mon-
itoring 2008”, cf. [1]. This Agreement entails the development of instrumentation, control and data
processing software, infrastructure and carrying out of measurements at the two candidate core sites,
plus at a selection of remote sites in the hosts proposed array configuration. This spectrum monitoring
report is one of a series.
1.1 Measurement types
The spectrum measurements were taken at the core sites and at the remote sites. Five types of measure-
ments have been carried out:
• Fast Scanning Mode (FS)
• High Sensitivity Mode (HS)
• Transient Mode (TM)
• Rural mode (RM)
• Max Hold mode (MH)
The results of each mode and of each separate run are presented in separate reports.
Fast Scan measurements have been taken at several times during the month-long campaign at the core
sites. Each of these FS measurements are reported in individually generated documents. The measure-
ments are interspersed with High Sensitivity Mode measurements and serve to provide an overview of the
RFI environment for all pointing directions and both polarizations, while the HS measurements concern
only one pointing direction and polarization per measurement set. As such the FS measurements provide
an overview of the spectrum in all directions and polarizations during the course of the campaign, albeit
at somewhat lower sensitivity because of the reduced integration time.
The spectrum measurement reports are coded by three identifiers. The first identifier is the measurement
number preceded with the letter M. The second identifier is the country at which the observations were
done: C1 and C2 for the two sites. The identifier C3 is used for reports which present results from both
sites. The third identifier denotes the measurement type: FS, HS, TR, RM or MH. The measurement
report code is a combination of the three identifiers separated by a dot.
6
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
1.2 Deviations from the RFI 2008-2011 agreement
Measurements have been conducted according to the RFI monitoring agreemement [1]. There are however
a few deviations from the specied measurment protocol:
1. Channel bandwidth. Due to hardware limitations, complexity issues, and planning issues, it turned
out to be very dicult to meet the 10 kHz channel bandwidth requirement. There was consensus
in the team that a moderate increase of the channel bandwidth would not hamper the monitoring
campaign, nor the data quality, nor compromise the monitoring campaign goals. The channel
bandwidths used are listed in table 1.
2. HS Mode integration time. There were two reasons to deviate from the suggested integration time
of 24 hours net for the HS measurements:
• Hardware development time was much longer than anticipated, and in combination with re-
strictions for doing the measurements at the core during a period of absence of self generated
RFI due to construction activities left only one month available.
• Artefacts generated by the FFT spectrometer turned out to be such that they can only be
calibrated out by equal length measurement phases for noise source on, off and antenna.
Therefore the measurement effciency was reduced from 90 to 33%.
Both arguments required the integration time to be reduced from 24 to 2 hours, and this constitutes
a reduction in sensitivity of√12 or 5.4 dB. Required sensitivties in dB(Wm−2Hz−1) can be found
in the agreement [8]. For the cores sites the aim was to be close to the RA769 sensitivities [4],
ranging from about -258 to -240 dB(Wm−2Hz−1). Due to these technical and observation time
limitations the achieved sensitivities are about a factor 10 higher than the (interpolated) RA769
values. The sensitivies for the other modes are lower than mentioned above as the integration times
for those modes are lower.
7
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
2 Measurement set-up
A description and technical details of the RFI campaign instrumentation can be found in [8]. This section
only briefly outlines the system and some of the used parameter settings. Figure 1 shows a simplified
block diagram of the system. A log periodic antenna (HL033) is connected to a low noise amplifier
(LNA) via a coaxial switching box. The signals are digitized and converted to spectra by using a digital
spectrometer backend.
In the Fast Scanning (FS), High Sensitivity (HS), Rural (RM), and Max Hold (MH) modes, the spectra
are time-averaged power spectra (resp. 1 ×10, 120 × 60, 10× 60, and 90 × 0.1 s). In the Transient mode
(TR) the power spectra are averaged over much smaller time intervals (500.000 × 1µs) as this mode is
intended to obtain high time resolution statistics.
A noise diode can be connected to the LNA in order to calibrate the system. The noise figure of the
diode, the gain of the antenna and LNA, and the switch losses are given in the appendix.
antenna
HL023cable 2 cable 3
cable 4
cable 1
switch
back-end
noise diode
LNA1
2
Figure 1: Simplified block diagram of the SKA spectrum monitoring system.
Note that the calibration methods involves an RF switch and cable 1, and that the antenna and cable
4 are not included the signal path while calibrating. This will give rise to a spectral ripple in the gain,
receiver temperature, and calibrated spectra. The ripple does not affect the detection of narrow-band
signals, but may impede detection of weak broadband signals.
2.1 Bandwidth and integration time of the modes
The used spectral ranges for the modes are shown in table 1. The table also shows the ADC sampling
frequency Fs, and the channel bandwidth ∆f .
8
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
f (MHz) Fs (MHz) ∆f (Hz)
70 - 200 975 29.8
200 - 430 975 29.8
430 - 530 780 23.8
530 - 850 960 29.3
850 - 1050 780 23.8
1050 - 1330 975 29.8
1330 - 1550 830 25.3
1550 - 1800 960 29.3
1800 - 2000 850 25.9
Table 1: Spectral ranges, sampling frequencies, and channel bandwidths.
9
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
3 Measurement programme
The measurements that were carried out can be classified into a number of categories, that aim to capture
a particular aspect of the RFI environment. These are summarised in the following paragraphs.
3.1 Fast Scanning mode (FS)
This mode has been carried out at the core sites and was intended to provide relatively rapid overviews
of the entire spectrum (all 9 bands) in all directions (4 pointings, 2 polarisations). The measurements
were repeated several times, at least once between instances of the long duration High Sensitivity mode
(HS) measurements.
The FS measurements have been carried out with the following instrumentation settings:
• integration time: 10 sec (per spectrum)
• number of repetitions: 1
• net on antenna integration time per pointing/polarisation/band: 10 s
• calibration: equal time on noise source on/off/antenna (10s/10s/10s), each repetition
One complete FS measurement (4 pointings, 2 polarisations, 9 bands), including calibration and overhead,
takes 100 minutes. The Fast Scanning measurements at the core sites have been carried out 10 times at
one of the sites and 9 times at the other site. The differences are caused by unforeseen circumstances
dealing with issues in the field.
3.2 High Sensitivity mode (HS)
The High Sensitivity mode is intended to maximise the sensitivity of the measurements by increasing the
integration time to limits set by the total available time at the core site. These measurements were only
carried out at the core sites. Available time at the remote sites precluded inclusion of this mode there.
One HS measurement uses the following settings:
• integration time: 60 s (per spectrum)
• number of repetitions: 120
• net integration time per pointing/polarisation/band: 7200 seconds (2 hours)
• calibration: equal time on noise source on/off/antenna (60s/60s/60s), each repetition
A complete scan (1 pointing, 1 polarisation, 9 bands), including calibration and overhead, takes a total
of about 2.9 days. For a complete survey, all pointings and polarisations, a total of about 23 days was
required.
10
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
3.3 Transient mode (TR)
Transient mode measurements have shown to be very time consuming because of the very large amount
of time required to read out the data from the hardware. In addition there have been hardware issues
that compromised the dynamic range. For this reason the transient mode was used only at the core site.
The following parameters apply:
• integration time: 1 µs (per spectrum)
• number of repetitions: 5 × 105 (elapsed time per scan 500 ms; captured in 16 blocks of 64 ms
continuous capture)
• net integration time per pointing/polarisation/band: 1 µs
• channel bandwidth: 1 MHz
• calibration: fractional calibration time (on noise source) 0.008 (noise diode on/off: 2ms/2ms; an-
tenna meas. 0.5s)
A complete TR survey thus requires 8 repetitions for all four azimuthal directions and both polarisations.
Including calibration and the overhead for writing of data from hardware to system disk one complete
measurement takes about 9 hours. This does not include the time required to read the data from the
system disk to off-line media.
3.4 Rural Mode (RM)
An intermediate integration time measurement mode is used at rural (remote) sites to obtain data at a
sensitivity high enough to provide useful rural (remote) site information, while limiting the required time
at the site. Therefore the sensitivity is less than the HS mode, but higher than with the FS mode. One
complete RM measurement uses the following settings:
• integration time per cycle: 60 s (per spectrum)
• number of repetitions: 10
• net integration time: 600 s
• calibration: equal time on noise source on/off/antenna (60s/60s/60s), each repetition
A complete scan (1 pointing, 1 polarisation, 9 bands), including calibration and overhead, takes a total
of about 5.8 hours. One complete survey, all pointings and polarisations, then takes almost 2 days.
11
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
3.5 Max hold Mode (MH)
The Transient mode (TR) measurements were not carried out at the remote sites. To capture RFI of
short duration at maximum levels − not time averaged, integrated levels − another measurement mode
was used at these remote sites: the pseudo Max Hold (MH) mode. In essence in this mode the hardware
operates in the same manner as in the FS and HS modes, but with very short internal spectrometer
integration time (100 msec), for a large number of repetitions. In software, the statistics including the
maximum and various percentile levels can be derived.
One complete MH measurement uses the following settings:
• integration time per cycle: 0.1 s (per spectrum)
• number of repetitions: 90
• net integration time: 0.1 s (for statistics), 9 s when integrated
• calibration: one calibration cycle per 90 repeats
A complete scan (4 pointings, 2 polarisations, 9 bands), including calibration and overhead, takes a total
of almost 1.3 days (the large number of files generated causes substantial overhead).
12
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
4 Calibration
This section describes the calibration and main signal processing algorithms used in the spectrum mon-
itoring. Only the formulas used are described, no detailed background information is given as this can
be found in literature, and for example in [3, 5, 6, 7]. In this section (and throughout the report) all
quantities are expressed in SI units.
4.1 Gain calibration
The gain of the monitoring system as depicted in figure 1 can be estimated using a noise diode. In this
calibration process three measurements are required: (1) measurements with a the noise diode switched
on, (2) a measurement with the diode switched off (being at ambient temperature and therefore presenting
as a matched load of ambient temperature) and (3) a measurement in which the antenna is connected to
the RF/IF chain. For the noise source on/off measurements, the diode output power needs to be known.
This power is related to the “excess noise ratio” ENR calibration data of the diode, which is available.
The noise temperature Thot of the noise diode when switched on is given by
Thot = (ENR+ 1)Tamb (1)
where Tamb is the ambient temperature in K. Given an ambient temperature Tamb and known values for
ENR, Phot is computed with the formula above. In the following a description is given of how the gain
is computed from the three observations mentioned above. Let the receiver temperature be denoted by
Trec, the noise source “on” temperature by Thot, the noise source “off” temperature by Tcold, the antenna
temperature by Tant, and the system temperature by Tsys. Denote the received power when the antenna
is connected by Pant, the received power when the noise source in off state is connected by Pcold, and the
received power when the noise source in on state is connected by Pon. Denote the electronic gain by Ge,
then the following relations hold.
Psys = GekB(Trec + Tant) (2)
Phot = GekB(Trec + Thot) (3)
Pcold = GekB(Trec + Tcold) (4)
Psys, Phot, and Pcold values are obtained from measurements, figure 2 shows examples. Here, the Boltz-
mann constant is denoted by k, and the channel bandwidth is denoted by B (in the actual computations,
the factor kB is incorporated in the gain factor Ge). Initially, Ge, Trec and Tant are unknown and must
be calibrated. The Tcold temperature of the noise source is equal to its ambient temperature, assumed
to be 300 K. Equations (3) and (4) imply that the gain can be deduced from hot-cold measurements
yielding values for Phot, Pcold, and Psys:
Ge =Phot − Pcold
Thot − Tcold(5)
Please note that the gain value computed here is the electronic gain, the antenna gain is not included.
Figure 3 shows an example of the estimated gain for the fast scanning mode.
13
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
0 200 400 600 800 1000 1200 1400 1600 1800 20000
20
40
60
80
100
120
140
160
180
200
f (MHz)
pow
er (
dB)
SKA monitoring 2010/2011, power, Virtual Site
raw data, measurementraw data, "cold"raw data, "hot"
Figure 2: Spectrum analyzer observed power: noise source on, noise source off, and measurements using the HL033
antenna. Clearly visible are the transitions between the nine processing bands.The bands have an artifical offset
of multiples of 10 dB for ease of inspection. Both the pass-band and blocking part of each of the nine bands are
shown.
4.2 Gain smoothing
For several reasons the integration times for the noise source on, noise source off and for the spectrum
measurements were equal for the FS, HS, and RM modes. As the electronic gain is used for calibrating
the power flux spectral densities, noise fluctuations of the gain estimates will increase the rms noise of the
calibrated spectra. In order to reduce this effect, a gain smoothing algorithm is available. Applying this
algorithm would lead to a small systematic error due to the spectral ripple. Although the gain smoothing
function is available, it is not used in the final data processing. The reason is that it turned out that
there are narrowband digital artefacts produced by the the digital system hardware and firmware . These
artefacts will of course also be present in the gain curve. Smoothing the gain curve (and increasing the
spectral resolution again by interpolation) will spread these artefacts to a larger fraction of the band.
For this reason it was chosen not to use the gain smoothing function.
The gain smoothing algorithm averages the estimated gains over frequency. The spectrum is divided
into blocks of Ngainsm spectral pixels and the median value is computed both of the gain and of the
frequencies of the gain data. The blocks are fixed, the processing is not done on “running” intervals. If
the number of frequency bins is not a multiple of Ngainsm then the last data point is copied so as to fill
14
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
0 200 400 600 800 1000 1200 1400 1600 1800 200040
45
50
55
60
65
f (MHz)
G (
dB)
SKA monitoring 2010/2011, gain, virtual site
Figure 3: Estimated gain for four pointing’s and two polarizations, clearly visible are the transitions between the
nine processing bands.
a full Ngainsm interval.
The spectral resolution of the smoothed data is restored to its original size by interpolating the median
values. Edge effects are avoided by including the first and last spectral points before interpolation. Figure
4 shows an example of the effect of gain smoothing on the estimated gains.
4.3 Noise temperature calibration
As a sanity check for the spectrum monitoring measurements the system temperature Tsys, receiver
temperature Trec, and the antenna temperature Tant are estimated and plotted.
The system temperature is defined by
Tsys = Trec + Tant (6)
Given an estimated gain Ge (eq.5), Tsys can be deduced using equation (2) and a measured value for
15
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
140 141 142 143 144 145 146 147
48.85
48.9
48.95
49
49.05
49.1
49.15
f (MHz)
G (
dB)
SKA monitoring 2010/2011, gain, virtual site
compr
Figure 4: Estimated gain for four pointings and two polarization, without and without 20-point median filtering
(gain smoothing).
Psys; the receiver temperature can be estimated by using equation (4), assuming Tcold is known:
Tsys =Psys
kBGe(7)
Trec =Pcold
kBGe− Tcold (8)
The antenna temperature can be estimated by using equations (2) and (8):
Tant =Psys − Pcold
kBGe+ Tcold (9)
Examples of estimated Tsys and Trec curves are shown in figure 5. The system temperature estimates
are, obviously, affected by RFI. Tsys estimates can be improved by applying filtering techniques in the
spectral and/or temporal domains.
4.4 Power sanity check
As the monitoring antenna is a directive antenna pointed at the horizon, one would expect that for
high frequencies the observed power in a noise source off measurement would be a few dB higher than
when the directive antenna is connected. The reason is that the noise source off temperature is Tamb
whereas the directive antenna looks partly at the cold sky and partly at the warm ground (at Tamb). At
16
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
0 200 400 600 800 1000 1200 1400 1600 1800 20000
50
100
150
200
250
f (MHz)
Tre
c (K
)
SKA monitoring 2010/2011, receiver temperature, virtual site
0 200 400 600 800 1000 1200 1400 1600 1800 20000
50
100
150
200
250
300
350
400
450
500
f (MHz)
Tsy
s (K
)
SKA monitoring 2010/2011, system temperature, virtual site
Figure 5: Estimated receiver temperature and estimated system temperature
frequencies below about 200 MHz, sky power dominates and the observed power for the measurements
with the antenna connected will be higher than for the noise source off measurements. This reasoning,
17
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
obviously, is only valid for spectral bands in which no RFI is present.
Figure 8 shows an example of measured spectra for the case in which an antenna is connected, compared
to a connected noise-source off case. The solid curves in the upper figure are observations in which the
noise source was connected; the dashed curves represent data obtained with the monitoring antenna
connected. The lower curve shows the difference in power between the two: Pant - Pcold
4.5 Antenna gain
The isotropic effective antenna area Aisoeff is given by
Aisoeff =
λ2
4π(m2) (10)
where λ is the observed wavelength in m. The antenna factor is defined as the ratio of the field strength
(E) of the impinging electromagnetic wave to the voltage (V) on the line connecting an antenna. The
linear antenna factor Ka is given by
Ka =
√1
AisoeffG
z0z
(m) (11)
with z0 = 120π the free space impedance, z the impedance of the line connecting the antenna, and D
the antenna directivity. The logarithmic antenna factor AF is given by
AF = 10 log10(Ka) (dBm−1) (12)
For the spectrum monitoring measurements an log periodic antenna, HL033, is used. This antenna has
a gain of 6 dB at 80 MHz to 7 dB at 2000 MHz. Intermediate values are interpolated. The effective
aperture for the antenna, Aeff is then computed by using
Aeff =λ2
4πGant (13)
Note: the antenna gain and effective area specified in this way are only correct in case the transmitter
is located in the direction in which the antenna points and in case the transmit and receive antenna
polarizations match. In case these do not match then the observed power flux density is an underestimate
of the actual power flux density. As a directive gain antenna is used in the measurements (R&S HL033),
with a gain of 6-7 dB, all measurements in the monitoring survey were conducted in four directions
(North, East, South, West) and two polarizations (horizontal and vertical). In this way in at least one
in eight observations the power flux density is not underestimated. For high elevation observations, the
observed power flux densities are always underestimated. For this reason satellite signals, not originating
from the direction of the horizon, should be assessed with levels up to 6 dB higher than indicated in the
spectra. No correction for this effect is incorporated in the data processing.
18
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
0 200 400 600 800 1000 1200 1400 1600 1800 200060
65
70
75
80
85
f (MHz)
pow
er (
dB)
SKA monitoring 2010/2011, matched power, virtual site
0 200 400 600 800 1000 1200 1400 1600 1800 2000−6
−4
−2
0
2
4
6
f (MHz)
pow
er (
dB)
SKA monitoring 2010/2011, matched power difference, virtual site
Figure 6: Upper figure: matched power observations Pcold (black) compared to an observation in which the antenna
is connected Pant (dashed curves); lower figure: Pcold − Pant
19
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
4.6 Flux calibration
Power flux density calibration
Let k denote the Boltzmann constant (k = 1.38 × 10−23JK−1), define the channel bandwidth under
consideration by ∆f (Hz), and let Ψsky (Wm−2Hz−1) denote the apparent sky power flux density. The
observed (system) power density Psys (in WHz−1 or arbitrary units1 can then be written as Psys =
kTsys∆f , which can be related to the apparent sky flux density Ψsys by Psys = ΨsysAeff . Assuming the
transmit and receive antenna polarizations match and the receive antenna points in the direction of the
transmitter, the equations above lead to the following relation:
Ψsys =kTsysAeff
(14)
Using the definition for Tsys (6) and using relation (2) give the relation between the measured power
spectrum Psys and Tsys:
Tsys =PsyskBGe
(15)
hence the calibrated flux density Psys is given by the equation
Ψsys =kPsys
kBGeAeff(16)
In this equation Psys is known from observations, Ge is known from equation (5), and Aeff is known from
equation (13). However, it was found that the digital backend contributed additive spectral features to
the data. Analysis shows that these features could be suppressed by subtracting noise diode off data
from the measurements. So in the formula above, Psys (antenna measurement data) is replaced by
Psys − (Pcold − Pcold,av). The Pcold data has a nonzero average value and a slope which must be removed
in order not to influence the flux estimation too much. For this reason the Pcold,av curve is introduced:
this is a straight line with the same average value and slope as the original Pcold data. A consequence of
this procedure, implemented in the data processing, is that the (apparent) sensitivity decreases with a
factor√2 (1.5 dB).
Interpretation
In frequency channels where signals from transmitters are the dominating power contributions to the
system, equation (15) gives the relation between the observed transmitter power and the estimated
power flux density. For frequency channels in which there is no transmitter signal present, equation (15)
gives an apparent sky flux related to system noise contributions. This is a “baseline curve”. Assuming
approximate values Tsys = 300K and an antenna gain ranging from 6 dB at 80 MHz to 7 dB at 2 GHz, the
apparent “baseline flux ranges from approximately -210 dB(Wm−2Hz−1) at 80 MHz to approximately -
180 dB(Wm−2Hz−1) at 2 GHz. In case the observed transmitter power is of the same order of magnitude
1in case the observed power Psyshas an unknown scaling factor, this factor will be calibrated and incorporated in the
electronic gain factor Ge; as mentioned before, in the data processing the factor kB is also incorporated in the gain Ge.
20
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
as the other system noise components or lower, then the noise contributions must be subtracted from
the data in order to get corrected power flux density estimates. This process is described in the next
paragraph.
Sensitivity
0 200 400 600 800 1000 1200 1400 1600 1800 2000−270
−260
−250
−240
−230
−220
−210
−200
−190
−180
f (MHz)
∆Ψ (
dB(W
m−
2 Hz−
1 ))
SKA monitoring 2010/2011, sensitivity, Virtual Site
sensitivity (T
sys)
sensitivity (Trec
)
RA769 lineRA769 continuum
Figure 7: Sensitivity example, computed according to equation (17) using estimates for Tsys and Trec compared
with RA769 values [4].
Given calibrated auto-correlation spectra with apparent power flux densities Ψsys, the standard deviation
σ of the noise fluctuations, or sensitivity, is given by
σ =√2
Ψsys√∆f∆τ
(17)
where ∆f is the channel bandwidth (Hz), and ∆t is the integration time (s). The factor√2 stems from
the noise diode signal subtraction procedure mentioned in the previous section. Given estimated values
for Tsys, table values for Aeff , and specified values for ∆f and ∆τ , one can compute expected values for σ.
Estimated values of Tsys may include observed transmitter signals, so an alternative is to use estimated
values for Trec instead. A third way to estimate the sensitivity is by computing σ directly from the data
using the standard deviation:
σ = stdev(Ψsys) (18)
21
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
this computation can be preceded by a detrending operation to remove a slope in the data. In this
computation of the median one has to take care not to include spectral channels affected by transmitter
signals. In the signal processing this is implemented by separating the spectrum in intervals of length
Ndet = 100. The values in each of these intervals are sorted and the median is computed over the lowest
xmed% of the sorted data, with typically xmed75 = %:
Ψmed = median(Ψsys) (19)
In the data processing, the power flux density and is computed using equations (17) and (18). The
spectral resolution of this data is reduced by a factor Ndet as this is the interval length the quantities
are computed from. If the number of samples is not an integer multiple of Ndet then the last estimate
of Ψmed and σ of the data sequence is replaced by the estimate in the one but last interval. The two
quantities Ψmed and σ are restored to their original spectral resolution by interpolation. Figure 7 shows
an example of the sensitivity ∆Ψ as a function of frequency computed using equation (17) using values
for Tsys and Trec, for an integration time of 10 s and for a bandwidth of 30 kHz. The sensitivities are
compared to the ITU-R-RA769 values [4]
4.7 Transmitter detection and baseline correction
Transmitter detection and baseline subtraction
Given frequency averaged measurement data Ψmed, calibrated original data Ψsys, and estimates of σ, one
can compute the “Boolean” function Ψdet which values are 0 in case no transmitter is detected and 1 in
case a transmitter is detected:
Ψdet =
{1 if Ψsys > (Ψmed +Nσ σ)
0 if Ψsys ≤ (Ψmed +Nσ σ)(20)
Here Nσ is an integer value for setting the detection threshold level. For those frequency channels in which
a transmitter is detected, the flux estimate Ψc (the “baseline corrected” flux) is computed according to:
Ψdetc = Ψdet(Ψsys −Ψmed) (21)
For frequency channels in which no interference is detected the Ψrfi values are set to the detection level:
Ψnodetc = (1−Ψdet)Nσ σ (22)
The baseline corrected power flux Ψc is then obtained by adding the “detected” spectra ψdetc and the
“non-detected” spectra Ψnodetc :
Ψc = Ψdet(Ψsys −Ψmed) + (1−Ψdet)Nσ σ (23)
22
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
The measurement protocol [1] specifies that the sensitivity curve Nσ σ should be added as separate plots.
However, the Ψc data already include threshold levels for the majority of the frequency channels (in
general the occupancy factor is much smaller than one). In the Ψc curves, the “detected” channels
are plotted with colours different from the “not-detected” channels. Therefore no separate additional
sensitivity plot is added for every measurement, however, a generic sensitivity curve is added based on
equation (18).
0 200 400 600 800 1000 1200 1400 1600 1800 2000−240
−230
−220
−210
−200
−190
−180
−170
−160
−150
−140
f (MHz)
Ψ (
dB(W
m−
2 Hz−
1 ))
SKA monitoring 2010/2011, power flux spectra, corrected, Virtual Site
data, Ψ: baseline (noise) + RF baseline corrected data, Ψ
c
1σ base linedetection flag
Figure 8: Power flux density Ψ in dB(Wm−2Hz−1), obtained for two polarizations and four pointings. For each
of the nine bands eight curves are plotted. Green (upper) set of curves are calibrated observed data, the blue set
of curves are the estimated flux rms levels using a Nσσ threshold level (Nσ = 6). The red curve is the estimated
1σ level. The small 3 dB spikes on the lower black horizontal line at -235 dB(Wm−2Hz−1) (the detection flag)
indicate detected interference.
4.8 Occupancy statistics
The detection data computed from (20) averaged over Nsp consecutive spectra is plotted as a function of
frequency. The occupancy numbers are the fraction of time in which an interferer was detected given a ≈30 kHz wide channel. In addition to these spectra, bar charts are also included in which the occupancy
statistics in wider frequency bands are computed. For the bar charts the frequency intervals used are the
same as for mode two in the 2005/2006 campaign [2], cf table 2. The 2005/2006 frequency ranges were
not specified for frequencies below 150 MHz, so the interval 80-150 MHz was added. Also, the 2006/2007
interval starting at 1723 MHz was truncated at 2000 MHz.
23
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
WGRM frequency ranges (MHz)
80 - 150 608 -614
150 - 153 614 - 1000
153 - 322 1000 - 1370
322 - 329 1370 - 1427
329 - 406 1427 - 1606
406 - 410 1606 - 1723
410 - 608 1723 - 2000
Table 2: List of frequencies as specified in [2] for mode two.
4.9 Time statistics and averaged power statistics
Time statistics
As the sheer number of data makes it impractical to display time-frequency spectra over the full time
and spectral resolutions the reporting includes percentile values over time. This kind of plot gives an
impression of the time-behavior of transmitters. Percentile values of 50 (median), 90 and 99 are used
and plotted in each figure. This kind of display is used for flux density data; in other cases (calibration
measurement results) other percentile values are used, e.g. 25, 50 and 75 percentile values. An overview
of occupancy statistics will be made available in the summary annex report.
Power statistics
Observed power flux densities Ψsys, averaged over frequency intervals as specified in table 2 (as numbers
or in the form of a particular figure of merit (FOM)) is outside the scope of the measurement campaign
(cf. [1]) and are not included in the measurement reports.
Interpretation of these power (FOM) data, if/when available, for example in terms of required ADC bits
is complicated and should be done with great care as misinterpretation is very easy. There are many
aspects which should not be forgotten when interpreting, for example:
• Satellite signals usually do not enter via the main lobe of the receiving antenna, therefore an (≈6dB)
fudge factor is needed (no corrections were made in the signal processing for this effect)
• A power FOM for the core probably will be different from the FOM for remote sites, and it is not
clear how these should be weighted
• There is day-night variation which is not sampled well temporally
• Power summation for a SKA receiver band will depend obviously on the selected band, and these
24
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
have not yet been fixed
• Transmitter “duty cycle” and the integration time of the digital receiver in most cases do not match,
this will lead to underestimates if uncorrected
• The spectrum environment is subject to change
4.10 Figure compression
The spectrum monitoring reports use eps formatted figures. This format is a vector format. Without
compression the figure data size would be of the order of a few Mbyte or larger. This would lead to reports
with a file size well over 100 Mbyte. For this reason an additional compression step (ranging between 10
and 100) is introduced when eps figures are produced. The compression is applied as a last step: all data
processing, calculation of RFI metrics and calibration is done with full spectral resolution. Figure 9 and
shows the effect of the applied filter. The filter computes for a specified interval (between 10 and 100
samples) the minimum and maximum value and plots both. As long as the pixel size of a computer screen
or the resolution in a document is larger than the compression interval, the impression/presentation of
the data is not affected. The fine structure related to the compression, as is visible in figure 9, is not
visible when the spectrum is ”zoomed-out“. The compression is applied to fixed length intervals, not on
running intervals.
25
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
130 131 132 133 134 135 136 137 138 139 140−220
−210
−200
−190
−180
−170
−160
−150
f (MHz)
Ψ (
dBW
m−
2 Hz−
1 )
SKA monitoring 2010/2011, power flux spectra, virtual site
130 131 132 133 134 135 136 137 138 139 140−220
−210
−200
−190
−180
−170
−160
−150
f (MHz)
Ψ (
dBW
m−
2 Hz−
1 )
SKA monitoring 2010/2011, power flux spectra, virtual site
Figure 9: Calibrated flux data, compressed using 10 point compression (upper figure) and without compression
(lower figure).
26
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
5 Output description and measurement result summary
5.1 FS mode results
The FS mode graphical output spectra are given for the actual calibrated spectra and sensitivity curves,
and for calibration spectra.
5.1.1 Spectrum measurement spectra
1. Calibrated and baseline-corrected power flux density. Calibrated and baseline-corrected (mean)
power flux density curves Ψc in dB(Wm−2Hz−1) obtained for two polarizations (H,V) and four
pointings (N,E,S,W): for each of the nine bands 2x4 curves are plotted. The Nσσ detection flag
curve (Nσ=6) is plotted in black at -235 dB(Wm−2Hz−1), detections are indicated by 3 dB vertical
spikes.
2. Sensitivity. Sensitivity ∆Ψ in dB(Wm−2Hz−1) estimates are obtained based on calibrated Tsysand on Trec curves, for two polarizations and four pointings; in total two times eight curves are
plotted. The depicted estimations are 1σ values, the actual detection level used is Nσσ (Nσ = 6).
The RA769 values for line and continuum sensitivities are included for reference; the values are
connected via dotted lines.
5.1.2 Calibration spectra
1. Raw spectra. Raw measurement data (dB) are presented for noise source “on”, noise source “off”
and for spectrum monitoring measurements, obtained for two polarizations and four pointings.
In total eight curves are plotted for each band. For reference the entire passbands are plotted,
not just the in-band part. The bands are plotted with multiple offsets of 10 dB (increasing with
bandnumber) to more clearly separate the bands for visual inspection.
2. Gain. Calibrated gain curves G in dB, obtained for two polarizations and four pointings are
presented. In total eight curves are plotted for each of the nine bands. Only the in-band sections
are depicted; the “jumps” are band transitions.
3. Receiver temperature. Receiver temperature Trec in K, obtained for two polarizations and four
pointings are presented. In total eight curves are plotted for each of the nine bands. Only the
in-band sections are depicted; the “jumps” are band transitions.
4. System temperature. System temperature Tsys in K, obtained for two polarizations and four point-
ings are presented. In total eight curves are plotted for each of the nine bands. Only the in-band
sections are depicted.
27
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
5. Matched power. Matched power in dB for a noise source-off measurement and for a measurement
in which the antenna is connected, obtained for two polarizations and four pointings, are presented.
In total eight curves are depicted for each of the nine bands. The spikes in the measurement data
are (obviously) caused by external RFI.
6. Matched power difference. Matched power difference curves in dB for a noise source-off measurement
and a measurement in which the antenna is connected, obtained for two polarizations and four
pointings, are presented. In total eight curves are depicted for each of the nine bands. The spikes
in the data are (obviously) caused by external RFI.
7. Calibrated spectra and detection level. Power flux density Ψ in dB(Wm−2Hz−1), obtained for two
polarizations and four pointings are presented. For each of the nine bands eight curves are plotted.
Green (upper) set of curves are calibrated observed data, the blue set of curves are the estimated
flux rms levels using a Nσσ threshold level. The red curve is the estimated 1σ level. The small 3 dB
spikes on the lower horizontal line at -235 dB(Wm−2Hz−1) (the detection flag) indicate detected
interference.
8. Data error table. A table is presented with numbers indicating whether a particular band is affected
by saturation of by a frequency offset error (1) or not (0). The header “B” denotes bandnumber,
“A” denotes azimuth (N,E,S,W), and “P” denotes polarization (H,V). The next four columns ϵs,m,
ϵf,m, ϵf,h, and ϵf,c indicate respectively: saturation flag for antenna measurements, frequency error
for antenna measurements, noise diode hot and noise diode cold error flag. The last column ϵallindicates the aggregate error flag.
5.2 HS mode results
The HS mode graphical output spectra are given for the actual calibrated spectra and sensitivity curves,
and for calibration spectra.
5.2.1 Spectrum measurement spectra
1. Calibrated and baseline-corrected power flux density. Baseline corrected power flux density Ψc in
dB(Wm−2Hz−1), obtained for one polarization and one pointing using Nσ = 6 are given. For
each of the nine bands three percentile curves are depicted: 50 percentile in blue, 90 percentile in
green, and 99 percentile in red. The Nσσ detection flag curve (Nσ=6) for all data (not just the
depicted percentile data) is plotted in black at -255 dB(Wm−2Hz−1), detections are indicated by
3 dB vertical spikes.
2. Sensitivity. Sensitivity estimates ∆Ψ in dB(Wm−2Hz−1) based on calibrated Tsys and on Treccurves are given. The depicted estimations are 1σ values, the actual detection level used is Nσσ.
The RA769 values for line and continuum sensitivities are included for reference.
28
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
3. Occupancy spectra. Occupancy spectra, obtained for one polarization and one pointing, are given.
The number of one-minute integrated spectra used for the occupancy estimate is: 120 minus the
number of erroneous spectra (cf. Nflag parameter in the figure shown, and section A6 of the
measurement report). The 1σ detection levels are displayed in section A5 of the measurement
report; the actual detection level used is Nσ = 6.
5.2.2 Calibration spectra
1. Raw measurement data. Raw measurement median power data (dB) for noise source ”on”, noise
source ”off” and for spectrum monitoring measurements obtained for one polarization and one
pointing. The median values are computed using 120 one-minute integrated spectra.
2. Gain. Calibrated gain curves G in dB, obtained for one polarization and one pointing. Only the
in-band sections are depicted; the “jumps” are band transitions. Plotted are the 25, 50, and 75
percentile curves, respectively.
3. Receiver temperature. Receiver temperature Trec in K, obtained for one polarization and one point-
ing. Only the in-band sections are depicted; the “jumps” are band transitions, the spikes are
self-genererated interference. Plotted are the 25, 50, and 75 percentile curves, respectively.
4. System temperature. System temperature Tsys in K, obtained for one polarization and one pointing.
Only the in-band sections are depicted. The pikes in the spectrum are caused by RFI. Plotted are
the 25, 50, and 75 percentile curves, respectively.
5. Matched power difference. Matched power difference (median value) in dB for a noise source-off
measurement and a measurement in which the antenna is connected, obtained for one polarization
and one pointing. The spikes in the data are caused by RFI.
6. Baseline and calibrated spectra. Power flux density Ψ in dB(Wm−2Hz−1), obtained for one polar-
ization and one pointing. The upper green curve is the median of the calibrated observed data, the
blue curve is the median of the baseline corrected data using an Nσσ threshold level with Nσ = 6.
The red curve is the estimated 1σ level. The Nσσ detection flag curve (Nσ=6) for all data (not just
the depicted percentile data) is plotted in black at -255 dB(Wm−2Hz−1), detections are indicated
by 3 dB vertical spikes.
7. Data error flag. Data flag for data affected either by a frequency offset error or by saturation. The
title includes the number of flagged measurements for each of the nine bands.
5.3 RM mode results
To be written.
29
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
5.4 MH mode results
To be written.
5.5 TM mode results
To be written.
30
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
References
[1] B.J. Boyle, P.J. Diamond, B. Fanaroff, M.A.Garrett, and R.T. Schilizzi. Agreement on Radio Fre-
quency Interference (RFI) Monitoring 2008-2011. Technical report, April 2008.
[2] R.Ambrosini et al. RFI measurement protocol for candidate SKA sites. Technical report, SKA,
S.Ellingson ed., May, 2003.
[3] S.W. Elingson et al. et al. et al. et al. Assessment of Radio Frequency Interference at Candidate SKA
Sites. Technical report, RFI Assessment Task Force (Limited Access), May 16, 2006.
[4] ITU. ITU-R-RA769. Technical report, ITU, 2005.
[5] John D. Kraus. Radio Astronomy. Cygnus-Quasar Books, Powell (Ohio), USA, second edition, 1988.
[6] R.P. Millenaar. SKA Site Spectrum Monitoring System Technical Description. Technical Report
RP-108, ASTRON, April 2006.
[7] R.P. Millenaar. SSSM System Design Considerations. Technical Report RP-13, ASTRON, February
21 2006.
[8] R.P. Millenaar, A.J. Boonstra, R. Beresford, and A. Tiplady. System description SKA RFI measure-
ment instrumentation. Technical report, SPDO, 2011.
31
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
Filename Mode Polarization Azimuth
SKAmon.M1.C*.FS.pdf FS H,V N,E,S,W
SKAmon.M3.C*.FS.pdf FS H,V N,E,S,W
SKAmon.M5.C*.FS.pdf FS H,V N,E,S,W
SKAmon.M7.C*.FS.pdf FS H,V N,E,S,W
SKAmon.M9.C*.FS.pdf FS H,V N,E,S,W
SKAmon.M11.C*.FS.pdf FS H,V N,E,S,W
SKAmon.M13.C*.FS.pdf FS H,V N,E,S,W
SKAmon.M15.C*.FS.pdf FS H,V N,E,S,W
SKAmon.M2.C*.HS.pdf HS H N
SKAmon.M4.C*.HS.pdf HS H E
SKAmon.M6.C*.HS.pdf HS H S
SKAmon.M8.C*.HS.pdf HS H W
SKAmon.M10.C*.HS.pdf HS V N
SKAmon.M12.C*.HS.pdf HS V E
SKAmon.M14.C*.HS.pdf HS V S
SKAmon.M16.C*.HS.pdf HS V W
Table 3: List of SKA monitoring measurement reports for the FS and the HS modi.
Appendix A. Measurement report list
Table 3 shows the filenames of the measurement reports produced. The table also lists the measurement
mode (FS: Fast Scanning mode, HS: High Sensitivity mode), the polarization (H: horizontal, V: vertical),
and azimuth (N: north, E: east, S: south, W: west).
32
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
f (MHz) Service / system f (MHz) Service / system
87.5 - 108 FM radio 1381 - 1381 GPS L3
150.05 - 153 RAS(1) 1330 - 1400 RAS(3)
137 - 138 METEOSAT 1400 - 1427 RAS(1)
174.0 - 230 Band III 1470 - 1480 AFRISTAR
245 - 270 FLTSATCOM 1525 - 1559 INMARSAT
322 - 328.6 RAS(1) 1570.42 - 1580.42 GPS L1
406.1 - 410.0 RAS(1) 1598.0625 - 1625.5 GLONASS
470.0 - 862 Band IV/V 1610.6 - 1613.8 RAS(1)
608.0 - 614.0 RAS(1a) 1616 - 1625.5 IRIDIUM
880.0 - 960 GSM900 1660 - 1670 RAS(1)
960.0 - 1164 DME 1710.1 - 1879.0 GSM1800
1226.6 - 1229.6 GPS L2 1718.8 - 1722.2 RAS
Table 4: Incomplete list of services and allocations in the bands relevant to the SKA monitoring 2010/2011
campaign. This table is included for ease of reference when inspecting spectrum monitoring graphs in this document
and its annexes. Note: (1) primary allocation, (1a) primary allocation in region 2,(2) secondary allocation, (3)
notification of use. Boldface bands indicate some of the satellite bands present.
Appendix B. Allocations and services
Table 4 shows a list of selected services and bands for ease of reference when inspecting spectrum SKA
monitoring figures. This list contains only a few services which may appear in monitoring spectra; this
list is not intended to be complete.
33
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
Appendix C. Component calibration data
For reference this appendix shows calibration data of components used: their gains, attenuation factors
and noise figures.
Appendix C1. Antenna gain
This section shows a typical gain curve of the HL033 antenna in figure 10 (upper figure) as given by
Rhode & Schwarz in the antenna fact sheet (http://www2.rohde-schwarz.com/). As it is expected that
the frequency dependent gain variation between different antennas of the same type is of the order of 0.5
dB, the gain curve used in the data processing can be a smoothed curve, as presented in the same figure,
below.
102
103
6
6.2
6.4
6.6
6.8
7Component calibration data, HL033, specified frequency range: 80−2000 MHz
f (MHz)
gain
(dB
i)
Figure 10: Gain curves of the HL033 antenna, a typical curve as specified by Rhode & Scwarz (upper figure) and
a smoothed curve used in the data processing (lower figure)
34
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
Appendix C2. LNA and noise diode properties
This section shows the measured LNA gain in figure 11 and the Excess Noise Ratio (ENR) of the noise
diode in figure 12 as specified in the noise diode fact sheet. The noise diode is specified in a much wider
freqeuncy range than is used for the SKA monitoring. As only three data points are available in the SKA
monitoring range, intermediate points are linearly interpolated. The expected deviations from the true
values are of the order of 0.05 dB or less.
102
103
47
47.5
48
48.5
49
49.5
50
50.5
51Component calibration data, LNA4, specified frequency range: 70−2000 MHz
f (MHz)
gain
(dB
)
Figure 11: Component calibration data, LNA AFS4
102
103
15.2
15.3
15.4
15.5
15.6
15.7
15.8Component calibration data, noise diode, specified frequency range: 10−18000 MHz
f (MHz)
EN
R (
dB)
Figure 12: Component calibration data, noise diode ENR (dB)
35
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
Appendix C3. Cable and switch attenuation
This section shows the attenuation of the cables and of the switches in the system in figures 13, 14, 15,
16, 17, and 18.
102
103
−0.9
−0.8
−0.7
−0.6
−0.5
−0.4
−0.3
−0.2
−0.1
Component calibration data, cable1, specified frequency range: 70−2000 MHz
f (MHz)
gain
(dB
)
Figure 13: Component calibration data, cable one
102
103
−1.4
−1.2
−1
−0.8
−0.6
−0.4
−0.2
0Component calibration data, cable2, specified frequency range: 70−2000 MHz
f (MHz)
gain
(dB
)
Figure 14: Component calibration data, cable two
36
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
102
103
−3
−2.5
−2
−1.5
−1
−0.5
0Component calibration data, cable3, specified frequency range: 70−2000 MHz
f (MHz)
gain
(dB
)
Figure 15: Component calibration data, cable three
102
103
−1.8
−1.6
−1.4
−1.2
−1
−0.8
−0.6
−0.4
−0.2
Component calibration data, cable4, specified frequency range: 70−2000 MHz
f (MHz)
gain
(dB
)
Figure 16: Component calibration data, cable four
37
Date of issue: July 25, 2011 Project: SKA Spectrum MeasurementRevision nr.: 0.3 Authors: A.J. Boonstra and R.P. MillenaarStatus: Draft Kind of issue: Limited
102
103
−0.35
−0.3
−0.25
−0.2
−0.15
−0.1
−0.05
0Component calibration data, switch1, specified frequency range: 70−2000 MHz
f (MHz)
gain
(dB
)
Figure 17: Component calibration data, SPDT switch, setting one
102
103
−0.35
−0.3
−0.25
−0.2
−0.15
−0.1
−0.05
0Component calibration data, switch2, specified frequency range: 70−2000 MHz
f (MHz)
gain
(dB
)
Figure 18: Component calibration data, SPDT switch, setting two
38