Sites Srl - Brochure 2015

7/23/2019 Sites Srl - Brochure 2015

1/8

ENGINEERING, TECHNOLOGY

AND SKID EQUIPMENTS

FOR OIL & GAS


2/8

COMPANY

ESTABLISHED IN 1989, AS A NATURAL DEVELOPMENT TO THE

EXPERIENCE OF ITS FOUNDERS, WITH THE BASIS OF ITS SPECIALIZED

SKILLS, IN OIL & GAS SKID MOUNTING EQUIPMENT.

FOR MORE THAN 20 YEARS WE HAVE GROWN UP EXPANDING OUR

KNOWLEDGE IN THE DESIGN, CONSTRUCTION AND MAINTENANCE

OF OIL & GAS EQUIPMENT.

MAIN ACTIVITIES:

DESIGN AND ENGINEERING: PROCESS, MECHANICAL, STRUCTURE,

ELECTRICAL AND INSTRUMENTAL;

SKID FOR FUEL GAS TREATMENT INCLUDING: FILTRATION UNIT,

INDIRECT GAS HEATING, PRESSURE GAS REDUCTION AND GAS

METERING SYSTEM FOR POWER GENERATION TURBINE;

SKID FOR INDIRECT GAS HEATER;

SKID FOR WELL HEAD WATER INJECTION;

SKID LUBE OIL CONSOLE COOLERS;

SKID FOR INJECTION AND ODORIZING OF NATURAL GAS;

SKID FOR CHEMICAL INJECTION AND MIXING REACTION TANK WITH

METERING DOSING PUMP;

SKID AND CONTROL PANEL FOR BURNERS MANAGEMENT SYSTEM

BMS.

ELECTRICAL & AUTOMATIONCONSTRUCTION WORKSHOP

MECHANICAL & PIPING CONSTRUCTION WORKSHOP

SKID ASSEMBLING &TESTING, SHIPMENT WORKSHOP


3/8

FUEL GAS IS COMMONLY USED TO FEED TURBINE ENGINES IN THE POWER

GENERATING INDUSTRY.

PRELIMINARY FUEL TREATMENT IS MANDATORY TO ENSURE REMOVAL OFSOLID, LIQUID AND GAS CONTAMINANTS.

SITES CAN OFFER COMPLETE TREATMENT PACKAGES.

FUEL FEEDING SYSTEM FOR GAS TURBINE ENGINES

FUEL GAS TREATMENTFOR THE POWER GENERATION INDUSTRY

FILTRATION UNIT: COMPOSED WITH N. TWO VERTICAL

COALESCENCE FILTERS SEPARATOR.

HEATING UNIT: COMPOSED BY TWO ELECTRIC

INDIRECT HEATERS IN PARALLEL INSTALLATION

(ONE IN SERVICE AND OTHER ONE IN STANDBY,

(N. 2 X 100%).

PRESSURE REDUCTION UNIT: THE REDUCTION

SYSTEM CONSISTS IN THREE LINES OF PRESSURE

REDUCTION, EACH WITH A CAPACITY NOMINAL

50% OF THE PRESSURE (PLUS OVERDESIGN 10%).

METERING UNIT: COMPOSED BY A CALIBRATED

ORIFICE AND DIFFERENTIAL PRESSURE METERINCLUDING PRESSURE AND TEMPERATURE

TRANSMITTER FOR VOLUME COMPENSATION.


4/8

INDIRECT GAS HEATERS

INDIRECT HEATERS USE MEDIA SUCH AS WATER, GLYCOL WATER, THERMAL OIL

OR COMBUSTION GASES TO TRANSFER HEAT TO PROCESS STREAMS THROUGH

A SEPARATE CHAMBER (E.G. A FIRE TUBE).

MAIN BENEFITS OF INDIRECT HEATING

HEATING MEDIA TRANSFER HEAT IN A UNIFORM WAY;

PROBABILITY OF CAKING, SCALING, AND PLUGGING (QUITE COMMON

PROBLEMS IN DIRECT HEATING) ARE SIGNIFICANTLY REDUCED BECAUSE OF

LOWER TEMPERATURE IN THE INSIDE WALL COIL.

MAIN PRODUCTS WE OFFER

WATER BATH HEATERS;

THERMAL OIL BATH HEATERS;

COMBUSTION GAS INDIRECT HEATERS EXCHANGER.

WORKING RANGE

SITES CAN OFFER INDIRECT GAS HEATERS FOR ALMOST ANY APPLICATION OF

OIL & GAS AND POWER GENERATION INDUSTRIES.

ITS PRODUCTS OPERATE RELIABLY, EFFICIENTLY AND SAFELY.


5/8

WELL HEAD WATER INJECTION

WELL HEAD WATER INJECTION IS USED TO INCREASE THE PRESSURE DROP OF

WELL DUE TO OIL EXTRACTION AND TO INCREASE THE RESERVOIR EXPLOITATION.

EFFICIENCY IN OIL RECOVERY CAN INCREASE FROM 30% (NO WATER INJECTION)

TO 51% (WITH WATER INJECTION).THIS TECHNOLOGY IS SUITABLE FOR BOTH ON-SHORE AND OFF-SHORE

APPLICATIONS.

WAG WELL WATER INJECTION

WAG WELL WATER INJECTION IS USED TO CLEAN WELLS.

STANDARD LAYOUT

SKID MOUNTED PIPES WORK

BALL VALVES

BUTTERFLY CONTROL VALVES

PRESSURE SAFETY VALVES

PRESSURE GAUGES

DRAINAGE SYSTEM

FIELD INSTRUMENTATION

AUXILIARY EQUIPMENT

ALL VALVES HAVE THE DBB DESIGN TO PROVIDE DUAL ISOLATION.

45-60%

OIL


6/8

LUBE OIL CONSOLE COOLERS

COMPRESSOR ROTATING PARTS GENERATE

SIGNIFICANT HEAT DUE TO MECHANICAL FRICTION.

FOR OPTIMUM EFFICIENCY AND LONGEVITY OF THE

EQUIPMENT IT IS ESSENTIAL THAT ALL MOVINGPARTS ARE PROPER LUBRICATED AND COOLED.

LUBE OIL CONSOLES (OR SKID) INJECT UNIFORMLY

CLEAN AND COOL OIL INTO BEARINGS BEFORE,

DURING AND AFTER COMPRESSOR OPERATION.

HOT OIL IS COOLED TROUGH AN HEAT EXCHANGER.

STANDARD LAYOUT

INDEPENDENT SKID

MAIN OIL PUMP

AUXILIARY OIL PUMP

TWIN OIL FILTERS (HEAT EXCHANGERS) AN OIL RESERVOIR

INTERCONNECTING PIPES

NECESSARY CONTROL SYSTEMS

ODORISING OF NATURAL GAS

ODORISING OF NATURAL GAS IS A FUNDAMENTAL

SAFETY ISSUE WHEN DELIVERING GAS FOR BOTHINDUSTRIAL AND PUBLIC NEEDS.

DETECTING LEAKAGES IN THE DISTRIBUTION

NETWORK CAN AVOID ACCIDENTAL INGNITIONS

AND EXPLOSIONS.

CHEMICAL INJECTION, MIXING REACTIONTANK AND METERING DOSIG PUMP

CHEMICAL INJECTION PACKAGES REQUIREMENTS

IN THE OIL AND GAS INDUSTRY ARE VERY

DIFFERENT - DEPENDING ON THE APPLICATION,

LOCATION, NUMBER OF CHEMICALS, MULTI-

POINT INJECTION, INCREASES IN PRODUCTION

OUTPUT AND CHANGES IN PRODUCTION

CONDITION.


7/8

CONTROL SYSTEM FOR DIRECT-FIRED

MULTIPLE BURNER HEATERS, FOR FLARE

GAS, INCINERATOR, BOILERS ECC.

MAIN FUNCTION OF BMS IS TO ALLOWAND ENSURE FIRED HEATER SAFE START-

UP, OPERATION, AND SHUTDOWN. ONCE

THE LOGIC IS CONFIGURED AND THE

SYSTEM PROPERLY COMMISSIONED, BMS

WILL PROVIDE A SAFE AND CONSISTENT

OPERATING SEQUENCE. HUMAN INTERFACE

WILL GUIDE THE OPERATOR IN ORDER TO

SAFE OPERATE AND, IF NEEDED, QUICKLY

AND SAFELY RESTART HEATER.

COMPLETE FUEL SKID OF(BMS) INCLUDING GAS TRAIN VALVES.

SAFETY CONTROL PANELS AND BURNER MANAGEMENTSYSTEMS (BMSS)

Cheek

Permissives

Burner

ManagementSystem

Burner Management System

PowerOn

StartPurge

ContinueCheck

Permissives

CompletePurge

Handto DCS

IgnitePilot(s)

ConfirmBurner(s)

ProvePilots

LightBurner(s)


8/8

T

8

Fenegr

urate

Lomazzo

VareseVarese

ComoComo

Meda

Cermenate

Appiano G.

Mozzate

Lomazzo

Saronno

urate

Fenegr

Malpensa

A-9

Torino

MilanoMilano

Venezia

TSITES S.R.L.

Via Trento, 82

22070 Fenegr (Como) Italy

Tel. 0039 031 35.200.81

Fax 0039 031 35.208.63

Web: www.sitessrl.com

e-mail: [email protected]

Fiscal Code 01937280129

VAT Code 01994280137

Sites Srl - Brochure 2015

Documents

Transcript of Sites Srl - Brochure 2015