Single Zone LCD Thermostat User’s Guide - Bryant R.Vbryantrv.com/docs2/docs/operating/Single Zone...
1
Single Zone LCD Thermostat User’s Guide Error Code: E1 Loss of communication between the Single Zone LCD thermostat and module board. LCD will cycle between E1 and previous mode setting. System will shut down. E2 Open circuit or out of range Indoor Temperature Sensor. Heating and cooling operation will be locked out. Fan op- eration can continue to operate. E3 Shorted Indoor Temperature Sensor. Heating and cooling operation will be locked out. Fan operation can continue to operate. E4 Open circuit or out of range Outdoor Temperature Sensor (Select Models). Heat pump will be locked out. Air condi- tioner, furnace, and fan mode of operation can continue to operate. E5 Open circuit or out of range Freeze Sensor. Air condi- tioner mode of operation will be locked out. Furnace, heat strip, heat pump, and fan mode of operation can continue to operate but displays the last temperature set-point. REVISION Form No. 3313325.031 10/10 (French 3313326.039) ©2010 Dometic, LLC LaGrange, IN 46761 USA SERVICE OFFICE Dometic, LLC 2320 Industrial Parkway Elkhart, IN 46516 574-294-2511 CANADA Dometic, LLC 46 Zatonski, Unit 3 Brantford, ON N3T 5L8 CANADA 519-720-9578 For Service Center Assistance Call: 800-544-4881 Special Features: • Auto Fan See Operating Instructions for more Information on this special feature. LCD Error Code When the system determines that one of the faults listed below has occurred an error code will be displayed in the LCD. In the unlikely event you experience a system failure, refer to the “SERVICE” section of the Operating Instructions furnished with your unit. Dometic Single Zone LCD Thermostat Quick Start-Up The basic steps for operating your Air Conditioner or Heat Pump are described in this User’s Guide. For more detailed information on modes of operation and special features refer to the Operating Instructions Manual. Quick reference to control buttons Press to decrease temperature set-point Press to increase temperature set-point Indicates mode of operation when illuminated * Select models Press to select mode of operation On/Off Mode Fan Cool Furnace *Heat Pump or Heat Strip ˚F Fan Mode Setting 1. Press and release the On/Off Mode button. Press and release the “+” or “―” button to cycle through the fan speed options (Lo (Low), Hi (High), Au (Auto)). On/Off Mode Fan Cool Furnace Mode of Operation A mode is an operation that can be performed by the Dometic Single Zone LCD Thermostat. 2. Press and release the On/Off Mode button to cycle through the available modes. All Dometic Single Zone LCD Thermostats have Cool and Furnace modes. Select models will have an additional mode, either Heat Pump or Heat Strip. When desired mode has been selected, the LCD will display the temperature set-point and the green LED will be lit next to the selected mode. To change the set-point, press the “+” button to increase the set point and the “―” button to decrease the set-point. On/Off Mode Fan Cool Furnace ˚F On/Off Mode Fan Cool Furnace ˚F Inside Temperature 3. To display the Inside Temperature, the Single Zone LCD thermostat must be in the OFF Mode. Press either the “+” or “―” button to display the Inside Temperature.
Transcript of Single Zone LCD Thermostat User’s Guide - Bryant R.Vbryantrv.com/docs2/docs/operating/Single Zone...
Single Zone LCD Thermostat
User’s Guide
Error Code:E1 Loss of communication between the Single Zone LCD
thermostat and module board. LCD will cycle between E1 and previous mode setting. System will shut down.
E2 Open circuit or out of range Indoor Temperature Sensor. Heating and cooling operation will be locked out. Fan op-eration can continue to operate.
E3 Shorted Indoor Temperature Sensor. Heating and cooling operation will be locked out. Fan operation can continue to operate.
E4 Open circuit or out of range Outdoor Temperature Sensor (Select Models). Heat pump will be locked out. Air condi-tioner, furnace, and fan mode of operation can continue to operate.
E5 Open circuit or out of range Freeze Sensor. Air condi-tioner mode of operation will be locked out. Furnace, heat strip, heat pump, and fan mode of operation can continue to operate but displays the last temperature set-point.
REVISIONForm No. 3313325.031 10/10
(French 3313326.039)©2010 Dometic, LLCLaGrange, IN 46761
USASERVICE OFFICE
Dometic, LLC2320 Industrial Parkway
Elkhart, IN 46516574-294-2511
CANADADometic, LLC
46 Zatonski, Unit 3Brantford, ON N3T 5L8
CANADA519-720-9578
For Service CenterAssistance Call:
800-544-4881
Special Features:• AutoFanSee Operating Instructions for more Information on this special feature.
LCD Error CodeWhen the system determines that one of the faults listed below has occurred an error code will be displayed in the LCD.
In the unlikely event you experience a system failure, refer to the “SERVICE” section of the Operating Instructions furnished with your unit.
Dometic Single Zone LCD Thermostat Quick Start-UpThe basic steps for operating your Air Conditioner or Heat Pump are described in this User’s Guide. For more detailed information on modes of operation and special features refer to the Operating Instructions Manual.
Quick reference to control buttons
Press to decreasetemperature set-point
Press to increase temperature set-point
Indicates mode of operation when illuminated
* Select modelsPress to select mode of operation
On/OffMode
FanCool
Furnace*Heat
Pump or Heat Strip
˚F
Fan Mode Setting1. Press and release the On/Off Mode button. Press and
release the “+” or “―” button to cycle through the fan speed options (Lo (Low), Hi (High), Au (Auto)).
On/OffMode
FanCool
Furnace
Mode of Operation
A mode is an operation that can be performed by the Dometic Single Zone LCD Thermostat.2. Press and release the On/Off Mode button to cycle
through the available modes. All Dometic Single Zone LCD Thermostats have Cool and Furnace modes. Select models will have an additional mode, either Heat Pump or Heat Strip. When desired mode has been selected, the LCD will display the temperature set-point and the green LED will be lit next to the selected mode.
To change the set-point, press the “+” button to increase the set point and the “―” button to decrease the set-point.
On/OffMode
FanCool
Furnace˚F
On/OffMode
FanCool
Furnace˚F
Inside Temperature
3. To display the Inside Temperature, the Single Zone LCD thermostat must be in the OFF Mode. Press either the “+” or “―” button to display the Inside Temperature.
