Single Wardrobe - .NET Framework
Transcript of Single Wardrobe - .NET Framework
Flatblade screwdrivermedium
Philips screwdriverUK size #3 pozi head
0 0 20 30 40 50 60 70 80 90 00 0 20 30 40 50
0 2 3 4 5 6
Ruler/tapemeasure
Smallhammer
CordlessDrill
Eye protection
Spirit level
Saw
KND 01 rev. 03 Date: 10/05/19
Single Wardrobe
DIMENSIONS
Width
Depth
Height
40/45/50 cm
59 cm
226 cm
Pre-Assembly Preparation: please check the pack contents before starting to assemble this product.
Clean hands or light coloured protective gloves should be used. Please don’t wear dark protective gloves, as may mark the products.
Product is heavy. TAKE CARE when lifting to avoid personal injury and (or) damage to the product.
The fittings packs will contain SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Necessary Tools
Safety and care advice
IMPORTANT - PLEASE READ THESE INSTRUCTIONS FULLY BEFORE STARTING ASSEMBLY
• Check you have all the components and tools listed on pages 1,4 and 5.
Remove all fittings from theplastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts beforestarting.
• Do not stand or put weight on the panels, this could cause damage.
• Assemble the unit as close to its final position (in the same room) as possible.
• It is our recommendation touse a hand screw-driver when inserting screws for handles to prevent over-tightening
• Assemble on a soft level surface to avoid damaging the unit or your floor.
• Parts of the assembly will be easier with 2 people.
• If using power tools, please follow the safety instructions supplied with the tools.
• Skin contact: Removecontamination by washing with soap and water. This procedureshould also be followed prior to eating and drinking.
• Eye contact: Rinse immediately with clean water for 15 minutes and seek medical advice.
GLUE SAFETY - TAKE CARE WHEN USING GLUE, PLEASE FOLLOW THE ADVICE BELOW
CLEANING INSTRUCTIONS
• This product has been manufactured using modern manufacturing methods and materials. With appropriate in-home care and mainte-nance it will provide trouble free performances. Many domestic multi-purpose cleaning agents are unsuitable for use on this product.
• The use of aggressive chemicals can result in irreversible damage. Please follow these guidelines care-fully.
• To clean the internal and external area of yourwardrobe and chest of draw-ers, use only 5% soap, 95% water solution, wiping with a damp (not wet) cloth. Dry with a clean cloth.
• Dust your furniture with a soft clean cloth.
• For stubborn stains, on the exterior face of your furniture, we recommend the use of a solvent cleaner designed to remove dirt from furniture without harming the finish.
•
• Please dispose of all packaging carefully and responsibly.
Warning: Before attempting to fix to the wall, check the wall for hidden pipes and cables.
• If swallowed: Seek medical advice immediately. If possi-ble show product information label to your doctor
We recommend our own branded cleaning agent, which can be purchased through your retailer. If you wish to use an alternative product, it is advisable to test a small non visible area first, and then only treat the stained area.
• DO NOT USE wax furniture polish, abrasive or aggressive cleaners, bleach or hypochlo-rate (chlorine) based cleaners, multi-purpose cleaners, dilutes, acetone, alcohol, solvent or similar products.
2
Conformat x 12
Bumper x 2
clip hinge x 4 cover x 4 hinge mounting plate x 4
A
E
Wooden dowel x 22
B
4MAx23 Screw x 4
6MAx30 Screw x 2
27mm x 4
C
I
O
Note: The quantities below are the correct amount to complete the assembly. In some cases morefittings may be supplied than are required.
F
D
K L
G
J
M N
RP Q
15mm Screw x 12 35mm Screw x 24 x 1
H
SO
LD S
EP
AR
ATL
Y
Components -
Choose Mounting Method:
FittingsPlease check you have all the fittings listed below
Supportfoot x 4
Wedgefix dowel x 8Wedgefix housing x 8
Hanger railsupport x 2
30mm Screw x 8
hanging rail x 1
RecommendedNOT SUPPLIED
Wood Glue
STEP 1 STEP 6
Horizontal Vertical4.6 M floor clearance required 2.34 M ceiling height clearance required
5
Step 1
KK
I
B
B
4
B
B
x4
226cm 455cm
For back panel insertio
n
6
K
1
2
WoodGlue
Wood Glue not supplied
WoodGlue
WoodGlue
WoodGlue
Assembly Instructions Horizontal Wardrobe Assembly
6
structionsStep 2
Step 3
A
A
A
1
Back Edge – Location
of foil joint
2
4
4
A
A
A2
4
WoodGlue
WoodGlue
WoodGlue
WoodGlue
WoodGlue
WoodGlue
Wood Glue not supplied
Wood Glue not supplied
Raw on the back
Assembly Instructions Horizontal Wardrobe Assembly
6
6
6
6
7
structionsStep 6
A
A
A
A
1
6
6
6
6
Wood Glue not supplied
WoodGlue
WoodGlue
WoodGlue
Assembly Instructions Vertical Wardrobe Assembly
9
structionsStep 8
4A
Glue
4
Back Edge – Location of foil joint
Assembly Instructions Vertical Assembly Top/Side Panel Insertion
11
structionsStep 9
2
A
A
A
H H HH
11
HH H H
45
WoodGlue
WoodGlue
WoodGlue
Wood Glue not supplied
Assembly Instructions Vertical Assembly Top/Side Panel Insertion
12
Step 10
L
To level your wardrobe adjust the feet by turning clockwise to lower or anticlockwise to rise.
Assembly Instructions Height Adjustability
13
Step 13
Decor cutting
Decor position
Skirting profile
J
J
J
J
Thickness of skirting
Heightofskirting
25m
m
650
mm 35
mm
Ø5
Assembly Instructions Decor End Fixing
We recommend the use of a slave strip of board when cutting the panel. This will prevent breaking out of the board
material and foil. I twill also reduce the likehood of “lifting” of the foil should a coarse blade be used.
16
Step 14
Assembly Instructions Fitting Optional Plinth
Wood Glue not supplied
WoodGlue
no end panel required when
fitting more than
one robe unit
Ø5
J
J
J
45°
45°
17
Step 15
J
Door
J
Door
J
Door
J
Door
Assembly Instructions Fitting Optional Cornice
Wood Glue not supplied
J
J
J
45°45°
WoodGlue
18
Step 16
Step 17
Front
Back Edge – Location of foil joint
Assembly Instructions Fixing In Base Panel
5
C
C
DD
D
D
x2
5
5
19
Step 19
Assembly Instructions Hanging Rail And Shelf Positioning
I
I
M
M
O
A
B
5
5
O
D
D
D
D
Shelves require a
firm “click” into place
21
Step 20
R
R
R
R
P
P
P
PR
R
R
R
P
P
P
P
RP
R
P
CLASSIC
MODERN
Assembly Instructions Application Of Hinges To Door
E
E
E
E
E
E
22