Singapore CCTV Surveillance, Wireless, Security Alarm ...Singapore CCTV Surveillance, Wireless,...
Transcript of Singapore CCTV Surveillance, Wireless, Security Alarm ...Singapore CCTV Surveillance, Wireless,...
SOYALACCESS CONTROL SYSTEM
®AR-725E-M / AR-725E / AR-725X
V090819
a.
d. e.
A.
A1.
A2. A3.
B.
E.
B.
C.
F.
C. H.G. D.
D.
b. c.
P1
P1
P5
P5
P2
P2
P6
P6
P3
P3
P7
P7
P4
P4
P8
P8
d x1
b x2
a x2
c x2
e x2
d x1
c x2
2 C.
1
c.
A.
B.
3
45
A. B. C.6
A.
B.
D.
7
8
A.
C.
g.
d.
F.1
f.
A1.
F.E.
2
4
5e.
3
A3.A1.
G.
1
f.
2
3
e.
b. A2.
A1.+A3.H.
4
5
a.
D.
ContentsAR-725E-M
AR-725E
AR-725X
1 Products
1 Products
1 Products
2 User Guide
2 User Guide
3 Terminal Cables
3 Terminal Cables
4 Tools
4 Tools
2 Tools
Pull the cables from the square access hole of the mounting plate C. Use a screwdriver to screw the metal plate C to the wall. Take off the plastic mounting plate B from the body A, and pull the cables through the access hole of C and B, then connect to the body A. Assemble plate B with the body A, and embed the water proof strip D onto the plastic side frame. Assemble the body A onto the mounting plate C with the Allen key and screws (accessories supplied).Turn on the power and LED will light and beep will sound.
Use a screwdriver to screw the base F onto the wall. Attach the water proof gasket to the body A1, and pull the cables from the square hole of the base F, and connect to the body A1. Assemble the body A1 with the base F. Screw A1 and F tight with the Allen key and screws (accessories supplied).Turn on the power and LED will light and beep will sound.
Put on G, and attach A1 onto the plastic plate A3, and screw it with the Allen key and screws (accessories supplied).Put the ring O on the metal frame, and put them together onto the reader A1+A3, and screw them and buckle up the 4 buckles on the back. Embed the water proof strip D onto the frame side of the base. Following by the install process of AR-725E-M.
Button Head PozidrivTapping Screw: M3x10
Security Torx Screw: M3.5x15
Flat Head Cap PhilipsTapping Screw: 4x19.1
Button Head PozidrivSlotting Screw: 2.5x10
Flat Head Hex Socket Screw: M3x8
InstallationAR-725E-M
AR-725E
AR-725X
Parts Description
V090819
87654321
12
1234567
654321
654321
321
12
4321
P1
P5
P2
P6
P3
P7
P4
P8
AR-321H
EXIT
12345678
EXIT
12345678
E
N.C.COM
PB
12VGND
12VGND
Exit Switch
12VGND
12VGND
12VGND
12VGND
12VGND
N.O.GND
N.O.GND
N.O.
COM
PB
12VGND
P1 P1
3 Door ControllerIlluminated Touch-panel
Notice1. Tubing: The communication wires and power line should NOT be bound in the same conduit or tubing.
2. Cable selection: Use AWG 22-24 Shielded Twist Pair to avoid star wiring. Use CAT5 for TCP/IP connection.
3. Power supply: Don’t equip reader and lock with the same power supply. The power for reader may be unstable when the lock is activating, that may make the
reader malfunction. The standard installation: Door relay and lock use the same power supply, and reader use independent power supply.
4. Keypad lock: If 725E does not link [TCP / IP connection], the 725E keypad locks about 5 seconds after power transmission.Setting will work after
725E switches to stand-alone mode.
Connector Table
Wire ApplicationDoor Relay
Common-COM-Point
Door SensorExit SwitchAlarm Relay
Power
Wire ApplicationBeeper
LED
Door Output
Wiegand
Wire ApplicationReservationReservationTCP/IP Output
Reservation
Wire ApplicationWGB Exit SwitchWGB Door SensorWGA Exit SwitchWGA Door Sensor
Wire ApplicationAnti-Tamper Switch
Wire ApplicationTTL Serial Port
Wire ApplicationRS-485 for LiftController
P1Cable: P5Cable:
P6Cable:
P7Cable:
P8Cable:
P2Cable:
P3 P4Cable:
Description(N.O.)DC24V1Amp(N.C.)DC24V1Amp(COM)DC24V1AmpNegative Trigger InputNegative Trigger InputTransistor OutputMax. 12V/100mA (Open Collector Active Low)DC 12VDC 0V
DescriptionBeeper Output5V/100mA, LowRed LED Output5V/20mA, Max.Green LED Output5V/20mA, Max.Transistor OutputMax. 12V/100mA (Open Collector Active Low)Wiegand DAT: 0 InputWiegand DAT: 1 Input
DescriptionReservationReservationNet - TX+Net - TX-Net - RX+Net - RX-Reservation
DescriptionNegative Trigger InputNegative Trigger InputNegative Trigger InputNegative Trigger Input
DescriptionN.C.COMN.O.
DescriptionTransistor OutputMax. 12V/100mA (Open Collector Active Low)GND
DescriptionRS-485(B-)RS-485(A+)
ColorBlue White
Purple WhiteWhite
OrangePurpleGray
Thick RedThick Black
ColorPink
Yellow
Brown
Blue White
Thin GreenThin Blue
Color--
Orange WhiteOrange
Green WhiteGreen
-
ColorPurple WhiteOrange White
PurpleOrange
ColorRed
OrangeYellow
ColorBlack White
Black
ColorThick GreenThick Blue
Wire123456
78
Wire1
2
3
4
56
Wire1234567
Wire1234
Connect to Electric Bolt
Electric BoltMagnet Lock
Controller Controller
Push Button Push Button
POWER12VDC
POWER12VDC
POWER12VDC
POWER12VDC
Connect to Magnet LockWiring Diagram
Wire123
Wire1
2
Wire12
SOYALACCESS CONTROL SYSTEM
®AR-725E-M / AR-725E / AR-725X
V090819
EXIT
12345678
N.C.N.O.
COMCTL12V
12345678
AR-321H
AR-321H
Door Sensor
ALM12V
GND
12VGND
12VGND
12VGND
12VGND
12VGND
12VGND
N.O.GND
N.O.
COM
PB
12VGND
P1P1
BZRLEDGLEDWG 0WG 112VGND
BZRLEDGLEDWG 0WG 112VGND
12345678
123456
123456
BZRLEDGLED
WG 0WG 1
BZRLEDGLED
WG 0WG 1
12VGND
P3
P4
P1
N.C.N.O.COMCTL12V
E
BZRLEDGLEDWG 0WG 112VGND
12345678
1234
123456
EXIT
12VGNDExit Switch
12VGND
P3
P7
P1BZRLEDGLEDDoor OutputWG 0WG 1
PB-ADS-APB-BDS-B
AR-321H
Connect to Electric Strike
Connect to 2 Readers
Electric Strike Alarm
Controller
Controller
Reader A
Reader A
Reader B
Controller
Controller
Push Button
Push Button
Door Sensor
Door Sensor
Relay Outpot Module
Relay Outpot Module
POWER12VDC
POWER12VDC
POWER12VDC
POWER12VDC
POWER12VDC
POWER12VDC
POWER12VDC
Connect to Door Sensor
Connect to Door Controller
Electric Bolt
Adding and Deleting TagMode4/Mode8
Deleting All TagsInput 123456 (or Master Code) → 29 29
Deleting the Single TagInput 123456 (or Master Code) → 10 SSSSS EEEEE[e.g.] Delete User Address: 00058 Access programming mode → 10 00058 00058
9
9Deleting a batch of TagsInput 123456 (or Master Code) → 10 SSSSS EEEEE[e.g.] Delete User Address: 00101~00245 Access programming mode → 10 00101 00245
9
9
Adding the Single Tag or the Random tagsInput 123456 (or Master Code) → 19 UUUUU 00001 → Get Tag close to RF Area(Present the tag to the controller.) → OK (Memory location number)
[e.g.] User Address NO.100 and NO.101 have 2 pcs of random tags: Access programming mode → 19 00100 00001 → Get Tag close to RF Area → OK P.S. The First tag has now been added, present the rest of the tags one after the other to add them to the system as well.
Input 123456 (or Master Code) → 19 UUUUU QQQQQ → Get Tag close to RF Area (Present the tag with the lowest number to the controller.) →
OK (Memory location number)
Adding the Sequential tags
[e.g.] User Address NO.101 to NO.120 have 20 pcs of sequential tags:(62312~62332): Access programming mode → 19 00101 00120 → Get Tag close to RF Area(only use the tag NO.62312) → OK
Mode6※At the Mode 6, User Address = Card Code
Adding TagInput 123456 (or Master Code) → 11 SSSSS EEEEE → OK [e.g.] Add User Address: 00100~01254 Access programming mode → 11 00100 01254 → OK
Deleting All TagsInput 123456 (or Master Code) → 29 29
Deleting TagInput 123456 (or Master Code) → 10 SSSSS (or )EEEEE → OK[e.g.] Delete a tag with card code 62362 Access programming mode → 10 62362 62362 → OK
9
Tag Information
SITE CODE
CARD CODE
SITE CODE
CARD CODE
V090819
3 Door ControllerIlluminated Touch-panel
※ Mode 6 the number of users up to 65535, largely because of its read-only CARD CODE, unlike Mode4/Mode8 shall read the SITE CODE and CARD CODE.
Mode Support
Networking/Stand-Alone
Stand-Alone
Networking/Stand-Alone
User Capacity Access Mode
M4
M6
M8
V
X
V
V
X
V
V
X
V
V
X
V
64
X
64
unlimited
X
unlimited
30,000
X
30,000
16,000(0~15,999)
65,535(1~65535)
16,000(0~15,999)
Auto-show Duty time
Event Capacity
120 Holidays Duress Time
ZoneLift
ControlAnti-pass-
back1.Card only2.Card and PIN (4-digit PIN)3.Card or User address (5-digit) + Individual PIN (4-digit individual PIN)
1.Card only2.Card and PIN (4-digit public PIN= Arming PWD)3.Card or PIN (4-digit public PIN= Duress code)
1.Card only2.Card and PIN (4-digit individual PIN)3.Card or PIN (4-digit individual PIN)
Changing the Master CodeAccess programming mode → 09 PPPPPPRRRRRR [Input the 6-digit new master code twice.][e.g.] If want to changing the Master Code= 876112, input 123456 → 09 876112876112
ExitingInput
Access programming mode → 00 NNN MMM AAA BBB[NNN= Node ID: 000~254; MMM=725E Door NO.:1~255; AAA=WGA Door NO.:1~255; BBB=WGB Door NO.:1~255]
B. Changing the Node ID of Reader
Access programming mode → 04 N [N=4/6/8]C.Setting up the control mode (M4/M6/M8)
ProgrammingA. Entering and Exiting Programming Mode
EnteringInput 123456 or PPPPPP[e.g.] The Default Value= 123456, if already changed the Master Code= 876112, input 876112 → Access programming mode
Enable deviceAccess programming mode → 20 U DDD [Please refer to function default value for details.][e.g.] If the AR-725E set to exit reader, WGA set to access reader. Access programming mode → 20 0 128 → 20 1 192 [Please refer to function default value for details.]
Enable/Disable auto open zoneAccess programming mode → 20 U DDD [Please refer to function default value for details.][e.g.] If the AR-725E set to Enable aut open zone. Access programming mode → 20 0 004 [Please refer to function default value for details.]
[e.g.] If the WG-B set to Enable aut open door without presenting card. Access programming mode → 24 2 128 [Please refer to function default value for details.]
Enable/Disable auto open door without presenting cardAccess programming mode → 24 U DDD [Please refer to function default value for details.]
[e.g.] User address from 00152 to 00684 enable the anti-pass-back function: 26 00152 00684 0
Enable card userAccess programming mode → 26 SSSSS EEEEE N [N=0 Enable/ N=1 Disable/ N=2 Reset]
NN: 16 sets of auto-open zone (NN=00~15)HHMMhhmm=Starting time to ending time (e.g.: 08301200=08:30 to 12:00)6543217H= 7 days of week + Holiday (Sat/Fri/Thu/Wed/Tue/Mon/Sun) (F= 0: disable; 1: enable)
Setting up access timeAccess programming mode → 08 U NN HHMMhhmm 6543217H
Individual PWD (M4/M8)Card or PIN: Access programming mode → 12 UUUUU PPPP [e.g. User address: 00001 and PWD: 1234. Input 12 00001 1234 ]Card and PIN: Access programming mode → 13 UUUUU PPPP [e.g. User address: 00001 and PWD: 1234. Input 13 00001 1234 ]Public PWD (M6)PIN only: Access programming mode → 15 PPPP [Input 4-digit PWD, default value: 4321]Card and PIN: Access programming mode → 17 PPPP [Input 4-digit PWD, default value: 1234, disable PIN: 0000]
Usually, anti-pass-back is commonly applied to parking areas in order to prevent from multi-entry with one card at a time, or somewhere wants to monitor not only the access but also exit condition.
Door will keep opening after first man flashing card. When the reader is stand-alone, supporting only 16 sets of auto-open zone by device setting. Auto-open zone can extend up to unlimited sets by Networking.
D. Setting up the password
E. Anti-pass-back(M4/M8)
F. Auto Open Zone
SOYALACCESS CONTROL SYSTEM
®AR-725E-M / AR-725E / AR-725X
V090819
12
3
5
4
G. Lift control
Single floor
[e.g.] User address NO. 45 only can reach the elevator to the 24th floor: 27 00045 24
Access programming mode → 27 UUUUU LLUUUU=User Address LL=Floor number (01~64 floor/stop)
Connect with AR-401RO16B to control which floors the user will be able to access. [BAUD9600]
Set(G)
Floor/ StopL816243240485664
01234567
L614223038465462
L715233139475563
L513212937455361
L412202836445260
L311192735435159
L2
10182634425058
L19
172533414957
Please refer to below floor chart
Enable all devices: Access programming mode → Enable particular device: Access programming mode → U
Enable Arming status:
Disable Arming status:
Standby Mode
Standby Mode
Enter Program Mode
Card only
Card only
Card or Passcode
Card or Passcode
Card and Passcode
Card and Passcode
※ There is NO arming mode for M6. Factory default armingcode is: 1234. U=Reader unit (0=725E, 1=WGA, 2=WGB).
H. Setting Up the ArmingConditions:1. Arming is enabled2.Alarm system connected
Application:1. Door open too long: Door is open longer than door relay time plus door close time.2. Force open (Opened without a valid user card): Access by force or illegal procedure.3. Door position abnormal: When power is off and then on, reader on arming bffore power off.
[e.g.] User address NO. 168 can reach only the 6th and 20th floor: Access programming mode → 21 00168 0 00100000 → 21 00168 2 00001000 → OK
Multi floorsAccess programming mode → 21 UUUUU G LLLLLLLL[UUUUU=User address G: 8 sets of lift control (Input: 0~7) LLLLLLLL: 8 floors/stop setting (L=0=Disable, L=1=Enable)
Restoring Factory Settings
Appendix-Firmware Upgrade
Reset all device parameters and user card data
Reset all user card data:Access programming mode → 29 29
Reset IP Setting:Press “IP Resent Button” of main board for few seconds
Reset all device parameters and user card data:Access programming mode → 29 29 9
Get the upgrade software from SOYAL or our distributor and run “UdpUpdater” software
Update the firmware [Please login the SOYAL web to download the new ISP Firmware.]1. Input the Target Address and Port2. [Load Fide] open the documents that have the new ISP Firmware3. Click the new ISP Firmware and [Open] it4. Click [Update Device] to start the firmware update5. Till the screen shown [Program Completed]
Execute the software
The software is within SOYAL CD or Login the SOYAL web to downloads
Enable all devicesInduct valid card → Input 4 digit arming code →
Enable particular deviceInduct valid card → Input 4 digit arming code → U
Disable particular deviceInduct valid card → Input 4 digit arming code → U
Input 5 digit user address → Input 4 digit pass code → → Input 4 digits arming code → or U
Induct valid card → Input 4 digit pass code → → Input 4 digits arming code → or U
Disable all devicesInduct valid card → Input 4 digit arming code → 9
Input 5 digit user address → Input 4 digit pass code → → Input 4 digits arming code → or U9
Induct valid card → Input 4 digit pass code → → Input 4 digits arming code → or U9
V090819
3 Door ControllerIlluminated Touch-panel
IP Setting
Log-in User PasswordWhen you choose the "Networking Setting" or "User Password" at first.Log-in window will pop out and please input※ At the Factory DefaultUser name: adminPassword: No as default value,so please just press “OK” to log-in
Turn on your Web Browser and input factory default IP address: http://192.168.1.127
adminadmin
Networking Setting
You will find initial IP Address 192.168.1.127 and check MAC Address is the same as sticker on Ethernet Module device. Please revise IP address you want, and then click “Update” button. After updating the IP, please re-connect the Web Browser by new IP address.
User Password
The password composes of 10 characters at most, it can be either A~Z or 0~9.
Change the log-in password to lock the IP setting of Ethernet Module.
Max. 10 characters allowed(Composed of A~Z and 0~9)
After changed and updated IP to new address, re-connect the Web Browser by new IP address.
If the AR-725E of the IP address has changed We must enter the new IP address.
Show which computer is linking on Ethernet Module.
Current IP address of the AR-725E.
Page menu
Current State
Online Status is able to monitor and show which computer is linking on Ethernet Module
IP Setting
Monitor the on-line computer
Change the Log-in information
SOYALACCESS CONTROL SYSTEM
®AR-725E-M / AR-725E / AR-725X
V090819
Command ListFunctionEntering programming mode Exiting programming mode Exiting programming mode and enabling all device into arming status. (Including 725E, WGA and WGB)Exiting programming mode and enabling each device into arming status. (725E, WGA or WGB)Node ID setting
Door relay time setting
Alarm relay time setting Control mode settingArming delay time settingAlarm delay time settingMaster card setting(For entering programming mode instead of pressing master code)Auto-open zone setting
Master code settings Suspend or delete tags
M4/8: Recover tagM6: Setting up a batch of users to access by card onlySetting up the PWD/PIN
Setting up the PWD/PIN
Arming output settingM4/M8: Duress code settingM6: Public PIN setting(Card or PIN)
M4/M8: Arming PWD settingM6: Public PIN setting (Card and PIN)Enabling or Disabling into arming statusEnabling or Disabling target unit into arming statusEnabling all units into arming statusDisabling all units into arming status
ModeM4/M6/M8 M4/M6/M8 M4/M6/M8
M4/M6/M8
M4/M8
M4/M6/M8
M4/M6/M8
M4/M6/M8M4/M6/M8M4/M6/M8M4/M8
M4/M6/M8
M4/M6/M8 M4/M6/M8 M4/M8M6
M4/M8 M4/M8 M4/M6/M8 M4/M8M6
M4/M8M6
M4/M6/M8
Command PPPPPP
U
00 NNN MMM AAA BBB
02 U TTT
03 TTT
04 N 05 TTT 06 TTT07 SSSSS EEEEE
08 U NN HHMMhhmm 6543217H
09 PPPPPPRRRRRR
Suspend= 10 SSSSS EEEEEDelete= 10 SSSSS EEEEE11 SSSSS EEEEE11 SSSSS EEEEE
12 UUUUU PPPP
13 UUUUU PPPP
14 TTT15 PPPP
17 PPPP
Flashing a valid card and inputNNNNFlashing a valid card an inputNNNN UFlashing a valid card and inputNNNNFlashing a valid card and inputNNNN
9
ExpositionPPPPPP: Master Code, (Default value: 123456)
U= Enable target unit (0=725E, 1=WGA, 2=WGB)
NNN= Node ID of 725E: 001~254; MMM= Door number of 725EAAA= Door number of WGA; BBB= Door number of WGB U= Enable target unit (0=725E, 1=WGA, 2=WGB)TTT= Door relay time(Input 000=Normal open / Input 001~600=1~600 sec. /Input 601~609=0.1~0.9 sec. )TTT= Door relay time(Input 000=Normal open / Input 001~600=1~600 sec.)N= Mode: 4/6/8Base on second, range: 001~255 Base on second, range: 001~255Input a user or a batch of user as the master card: 00000~15999SSSSS= starting user address; EEEEE= ending user address
U= Enable target unit (0=725E, 1=WGA, 2=WGB)NN: 16 sets of auto-open zone (Range: 00~15)HHMMhhmm=staring time to ending time(e.g.: 08301200=08:30 to 12:00)6543217: 7 days of week -Sat/Fri/Thu/Wed/Tue/Mon/Sun(Input value: 0=disable; 1=enable)H: Holiday (Input value: 0=disable; 1=enable) PPPPPP= New master codeRRRRRR= Repeat the new master code = Suspend; = DeleteSSSSS= starting user address; EEEEE= ending user addressRecover the paused tagSSSSS=starting Card Code; EEEEE= ending Card Code
UUUUU= user address; PPPP=4-digit individual PWD(Access mode: Card or PIN) UUUUU= user address; PPPP=4-digit individual PWD(Access mode: Card and PIN)Base on 1ms, range:1~255, default value=10, Input 0= TimelessPPPP=4-digit PWD (P.S. Duress code will be unavailable and as public PIN at access mode “Card or PIN” of M6)(Default value=4321; disable PIN=0000)PPPP=4-digit PWD (Default value=1234; disable PIN=0000)
NNNN=4-digit arming PWDU=Enable target unit (0=725E, 1=WGA, 2=WGB)
9
9
V090819
SOYAL http://www.soyal.com
3 Door ControllerIlluminated Touch-panel
FunctionDoor close timeAdding tags by inductFactory setting-1
Lift control setting: multi-doors
Add/Delete tags by closing tags into RF area (M6 only)AR-401RO16/ AR-401RO16B relay time settingFactory setting-2
Real time clock settingAnti-pass-back(Enable user) Lift control setting: single doorDuress Function and Arming output settingDelete all tagSame tag reading interval timeAuto ring the clock alarm schedule
Holiday Setting
ExpositionBase on second, range: 000~255, default value: 15 sec.UUUUU= User address; QQQQQ= the amount of card U=Enable target unit (0=725E, 1=WGA, 2=WGB)DDD=Function default value(Please refer to function default value for details)UUUUU=User addressG: 8 groups of lift control (Input range: 0~7)LLLLLLLL: 8 floors/stop setting (0=Disable, 1=Enable) N=0=Delete tag; N=1=Add tagClose tag into RF area one by one.MMM= Node ID of lift controllerTTT= relay time: 000~600=1~600 sec.U= Enable target unit (0=725E, 1=WGA, 2=WGB)DDD= Function default value(Please refer to function default value for details)YYMMDDHHmmSS: Year/Month/Day/Hour/Min./Sec.SSSSS=starting user address; EEEEE=ending user addressP=0=Enable; P=1=Disable; P=2=Initial UUUUU=User Address; LL=Floor number (01~63 floor/stop)Arming output: FFF= 008 (default value)Duress Function: FFF= 000
Base on 10ms, range from 0 to 6000SS= 16 sets auto alarm schedule, range 0~15HHMM= HH:MM (ex. 0830: Ring bell at 08:30)TT=Period of time to ring bell(Base on second, range 01~99 sec.)6543217: 7 days of week -Sat/Fri/Thu/Wed/Tue/Mon/Sun(Input value: 0=disable; 1=enable)H: Holiday (Input value: 0=disable; 1=enable)MM= Month of year (01=Jan...10=Oct.)DD= Date of month (01=1st day of month)F= 0:Del; 1: Add
ModeM4/M6/M8M4/M8M4/M6/M8
M4/M8
M6
M4/M8
M4/M6/M8
M4/M6/M8M4/M8 M4/M8 M4/M6/M8 M4/M6/M8M4/M6/M8M4/M6/M8
M4/M8
Command18 TTT19 UUUUU QQQQQ20 U DDD
21 UUUUU G LLLLLLLL
22 N
23 MMM TTT
24 U DDD
25 YYMMDDHHMMSS26 SSSSS EEEEE P 27 UUUUU LL28 FFF 29 29 31 TTTT32 SS HHMMTT 6543217H
35 MMDD F
Thanks for YouTo have more detailed information, E-learning, and Q&A, please visits our website.
Function Default Value20 U DDDFunction Option Value Application
※Default Value
Time AttendanceAuto Re-lockAuto OpenWhen Access Mode is "Card and PIN", Readers can skip pressing PIN code.Exit by Push ButtonEnable force OpenAs Access/Exit Reader Anti-pass-back
※0: Yes※0: Disable※0: Disable※0: Disable 0: Disable※0: Slave※0: Exit※0: Disable
NetworkingNetworking/Stand-AloneNetworking/Stand-AloneNetworking/Stand-AloneNetworking/Stand-AloneNetworkingNetworkingNetworking
001002004008016032064128
1: No 1: Enable 1: Enable 1: Enable※1: Enable 1: Mater 1: Access 1: Enable
24 U DDDFunction Option Value Application
※Default Value
Stop Alarm by...
Open door immediately without 1st card presented at auto open zone.
※0: None
※0: Disable
Networking/Stand-Alone
Networking/Stand-Alone
064
128
1: Push button/ Door Closed 1: Enable
[e.g.] DDD value of AR-725E to Enable "Auto Open" + "Exit by Push Button" + "Anti-pass-back" =004+016+128= 148 As a result of that, the command will be 20 0 148
※ U = Enable target unit (0=725E, 1=WGA, 2=WGB); DDD = Value