SIMPLY THE BEST - Tescotesco-online.com/wp-content/uploads/2017/03/TES1515E.pdf · SIMPLY THE BEST...

1
INSTALLATION NOTES Load Cell Protection TES 15/15E DESCRIPTION ELECTRICAL SPECIFICATIONS 1. The TES 15 load cell protector should be installed close to the individual load cells so that the load cell cable lengths to the TES 15 protectors will be one foot or less. 2. It is highly recommended that each crimp lug connection be crimped and soldered for the best long term corrosion protection. 3. All TES 15 protector load cell connection termi- nals (except the green marked/green wired earth ground terminal) are non-polarized and are insen- sitive to lead placement position. Any signal lead, any exitation voltage lead, and the cable shield can be connected to any individual connection terminal. (See Figure 2 for examples.) 4. The TES 15 protector’s earth ground green wire lengths should be kept as short as possible with a two foot maximum. 5. The TES 15 protector’s earth ground green wires should be attached as close as possible to the individual load cell’s actual case to earth ground connections. 6. Cable shield should bypass the TES 15 located at the Digital Indicator AC ground or chassis ground. (See Figure 1.) 7. The green wire of the TES 15 located at the Digital Indicator should be connected to the Digital Indicator signal ground ( NOT chassis ground). This is normally the (-) side of the exitation voltage. Maximum Peak Voltage Protection 6 KV Maximum Peak Current Protection 6,000 AMPS Maximum 100 AMPS Voltage 9 V (voltage from any terminal to any other terminal) Maximum 100 AMPS Clamping 130 (voltage from any terminal to any earth ground) Operating Temperature Range -40 C to + 85 C c e S N 5 1 < e m i T e s n o p s e R 0 - V 4 9 g n i t a R e r i F Complete lightning and AC power line transient protection for a platform weighting system is provided with the installa- tion as specified of two TESCO products, the TES 7 AC line protector and the TES 15 load cell protector. Figures 1 & 2 show the recommended placement of these two TESCO products for a specified wiring and component locations for a four load cell weighting platform. SIGNAL LINE SIGNAL LINE SHIELD EXCITATION EXCITATION + - TO INDICATOR TO LOAD CELL WIRING DIAGRAM GREEN WIRE SIMPLY THE BEST 2051 N. Main St., Suite 219 • Coeur d’Alene, ID 83814 • www.tesco-online.com • 1-800-426-2826

Transcript of SIMPLY THE BEST - Tescotesco-online.com/wp-content/uploads/2017/03/TES1515E.pdf · SIMPLY THE BEST...

Page 1: SIMPLY THE BEST - Tescotesco-online.com/wp-content/uploads/2017/03/TES1515E.pdf · SIMPLY THE BEST 2051 N. Main St., Suite 219 • Coeur d’Alene, ID 83814 • • 1-800-426-2826.

INSTALLATION NOTES

Load Cell Protection TES 15/15E

DESCRIPTION

ELECTRICAL SPECIFICATIONS

1. The TES 15 load cell protector should be installedclose to the individual load cells so that the loadcell cable lengths to the TES 15 protectors will beone foot or less.

2. It is highly recommended that each crimp lugconnection be crimped and soldered for the bestlong term corrosion protection.

3. All TES 15 protector load cell connection termi-nals (except the green marked/green wired earthground terminal) are non-polarized and are insen-sitive to lead placement position. Any signal lead,any exitation voltage lead, and the cable shieldcan be connected to any individual connectionterminal. (See Figure 2 for examples.)

4. The TES 15 protector’s earth ground green wirelengths should be kept as short as possible with atwo foot maximum.

5. The TES 15 protector’s earth ground green wiresshould be attached as close as possible to theindividual load cell’s actual case to earth groundconnections.

6. Cable shield should bypass the TES 15 located at the Digital Indicator AC ground or chassisground. (See Figure 1.)

7. The green wire of the TES 15 located at theDigital Indicator should be connected to theDigital Indicator signal ground (NOT chassisground). This is normally the (-) side of the exitation voltage.

Maximum Peak Voltage Protection 6 KV

Maximum Peak Current Protection 6,000 AMPS

Maximum 100 AMPS Voltage 9 V(voltage from any terminal to any other terminal)

Maximum 100 AMPS Clamping 130(voltage from any terminal to any earth ground)

Operating Temperature Range -40 C to + 85 C

ceS N 51 <emiT esnopseR

0-V 49gnitaR eriF

Complete lightning and AC power line transient protection for a platform weighting system is provided with the installa-tion as specified of two TESCO products, the TES 7 AC lineprotector and the TES 15 load cell protector. Figures 1 & 2show the recommended placement of these two TESCO products for a specified wiring and component locations for a four load cell weighting platform.

SIGN

AL L

INE

SIGN

AL L

INE

SHIE

LDEX

CITA

TION

EXCI

TATI

ON+ -

TO INDICATOR

TO LOAD CELL

WIRINGDIAGRAM

GREENWIRE

     SIMPLY THE BEST

2051 N. Main St., Suite 219 • Coeur d’Alene, ID 83814 • www.tesco-online.com • 1-800-426-2826