Simple SWB Recumbent

7/23/2019 Simple SWB Recumbent

1/15

Simple SWB Recumbent

Here is a very simple 20 inch wheel short wheelbase recumbent bike that you can build in a few hours using nothingmore than a kid's bike and a few lengths of round tubing. This project makes a good starter recumbent and is a goodexperimenter's platform for those who want to try out various seating positions and angles. The completed bike doesn'tweigh much more than the bike used as parts, and can be stored in the same space as a regular bicycle. Of course, thissimple project lacks many of the more advanced features offered in our DIY Plans, but you could always add your ownmodifications to expand on this project.


2/15

You can build a 20 inch wheel short wheelbase recumbent from practically any kid's bike or BMX bike. You will need tostart with a working cycle or at least one that has functioning wheels, cranks, and a transmission system. The rearwheel should have a multi-speed freewheel so that you can have multiple gears, but you could also build the SWBaround a coaster hub and just make your bike single speed. If you want to climb a hill or reach any decent top speed,then you will need a rear wheel that has at least a 5 speed freehub.

Besides a working 20 inch bike, you will also need a few feet of round tubing. You can cut up another bike frame for thetubing, or just use some thin walled electrical conduit (EMT) for this project. Basically any square or round tubing with anapproximate 1.25 inch diameter and a wall thickness similar to bicycle frame tubing will work. The other part shown inthe photo is the bottom bracket and crankset that will be placed ahead of the front wheel. You can cut the bottombracket from another frame since the original bottom bracket will be unused and left on the frame. For more informationon bottom bracket sizes and assembly, see the tutorials on our main page.


3/15

This simple recumbent bike is made to fit the rider, so it has no adjustable seat or bottom bracket. For this reason, wewill make the seat first so that you can later use your body as a measuring system in order to determine the optimalplacement of the cranks for your leg length. Chop off the top of the seat tube as shown in the photo and then findanother 12 inch long tube that can be welded over the top of the cut-off seat tube. This tube will become your seat backtube, and it will support the back of the seat as well as set the recumbent angle of your seat.


4/15

The angle of the seat is completely up to you. Anything from 25 degrees to 35 degrees (taken from the horizontalground) will work. If you lean your seat back too much, then you will have to hold up your head, and if you set your seatto far forward, your knees will have to bend a lot while pedaling. Try a 30 degree angle and make only tack welds on theseat support tubing until you can sit on the frame and see if you like the angle. On a project like this, it is easy to makeadjustments, and since your frame parts will differ from the ones shown here, you will need to experiment.

To support the seat, the 12 inch long seat tube is welded to the top of the cut -off seat tube and then braces with anysmall tubing such as a seat of seat stays cut from another old frame. When you are testing your seat angle, you can getaway without the bracing as long as you don't put any hard pressure against the back of the seat. For riding though, youwill definitely need the seat tube bracing.


5/15

The seat will be held to the frame by a set of tabs that have holes drilled for woodscrews. Any 1 inch wide 1/8 inch orsimilar flatbar can be used to make the seat mounting tabs, and they are made 6 inches long so that there is about 3inches of material on each side of the frame tubing to mount the seat. Weld the seat mounting tabs to the frame so thatthe woodscrews will fasten each part of the seat in the approximate center of each board.

The seat mounting tabs shown here are welded to the frame so that each seat board will be held to the frame by a set ofwoodscrews. If you are not yet sure of your final seat angle, then leave out the seat back support tubing until you havehad a chance to sit on the frame and see if your seat angle is comfortable. You could also make an adjustable seat back


6/15

by hinging the seat back support tube and installing some kind of clamp that will allow the seat back support tubing to bemoved along the frame and then locked into position.

The seat is made of 3/4 inch thick plywood and foam as shown here. Feel free to make your seat any width and heightyou like, but for a reference, I like to make my seat base 10 inches wide at the back, 8 inches wide at the front, and 10

inches in length. I usually make the seat back 10 inches wide at the back, 8 inches wide at the top, and 12 inches inlength. To further enhance the seat, another top section can be added to support your upper back, but for now, thisbasic seat will get you started.

For seat padding, I used a firm 1.5 inch thick foam that has been cut to fit onto the plywood seat boards. You will needto install your seat padding before moving on with the frame design.


7/15

Fasten the two seat boards together where the meet using a pair of bent L-shaped shelf brackets so that your seatbecomes ones ingle assembly. You can then glue the foam to the plywood using some spray adhesive. The shelfbrackets will be strong enough to hold your seat boards together yet still allow some give if you want to force the seat

into another angle later as you make modifications to your bike. Once your seat is made, fasten it to the frame by usingthe four woodscrews through the seat mounting tabs installed on the frame.


8/15

The main difference between this bike and a regular upright bicycle is the fact that the cranks are placed ahead of thefront wheel rather than between the wheels. This recumbent position lets you push your full energy into the cranks andoffers both a comfort and aerodynamic advantage over a regular bicycle seating position. To get your cranks in front ofthe frame, you will need a set of tubes to create a triangulated boom and a bottom bracket to weld to the end of theseboom tubes. Unfortunately, you can't easily remove the unused bottom bracket from your frame and transplant it heresince it is holding all of your frame tubes together, so you will have to salvage one from another frame.

If you have to choose between a bottom bracket for a single piece cranks set and a 3-piece crankset, then choose thethreaded bottom bracket for a 3-piece crankset as these will offer the most selection when choosing a crank set (see outcrank and bottom bracket tutorials on the main page for more information). Clean up your bottom bracket shell with a

grinder and then make a fishmouth cut on one of your boom tubes to conform to the bottom bracket as shown here.Before cutting the boom tube length, read ahead to see how the length of the boom tubing will be determined.

The goal is to position the cranks over the front wheel in such a way so there is no pedal or crank arm interference withthe front wheel as it turns. If the crank arm were to hit the front wheel, the steering would be locked up, resulting in aloss of control. So basically, you want to position the bottom bracket as far ahead and as low as possible while at thesame time ensuring that the cranks do not interfere with the front wheel and so that they are placed the optimal distancefrom the seat for your leg length. To find the best bottom bracket position, sit on your seat (with shoes on), and extend

your leg while a helper holds the crank arm with pedal installed. Your helper can then take a measurement from thehead tube to the bottom bracket or crank center so you know the correct distance from the head tube to install thebottom bracket.

The lower front boom tube can then be cut and tack welded to the head tube as shown in the photo so that you can testthe crank position for both your leg length and clearance over the front tire. You may need to make fine adjustments tomeet both requirements, so take your time and get it right.


9/15

Once you have the lower front boom tube solidly tack welded in the correct position, you can measure the distance fromthe bottom bracket joint to the top of the head tube and cut the upper boom tube, that will form a triangle between thebottom bracket and head tube. This tube is also fishmouthed to fit the bottom bracket joint and the head tube to create agood joint for welding. The resulting triangulated front boom will be extremely strong, able to withstand any amount ofpedaling forces.

With the front boom installed, you can now install the cranks and rear derailleur to make up the long chain needed. Youwill need a chain about twice as long as a normal bicycle chain, but this is no problem, since you c an simply jointogether two chains to make a new one. For information on chain joining and sizing, see the tutorial on our main page.

When sizing the new chain, set it on the largest front chain ring and on the middle rear chain ring and then make it longenough to pull the derailleur into the position shown in the photo, with the top idler wheel just over top of the lower idlerwheel. You will also notice that the chain is in the way of the front wheel, but this will be fixed with the installation of theidler pulley.


10/15

An idler pulley designed for a 1/2 inch v-belt can be used to reroute the lower side of the chain over the front wheel asshown in the photo. There is never any tension on the lower (return side) of the chain, so it can be routed behind the top(drive side) of the chain, out of the way of the front wheel. Place the idler pulley on the lower front boom tube so that thelower chain will clear the front wheel and not rub on the top side of the chain. Any steel or nylon 2.5 inch to 5 inchdiameter idler pulley that includes a ball bearing will work. You can purchase a suitable idler pulley at many yard andgarden supply stores.


11/15

Once you have found the optimal place for your return chain guide pulley, weld the bolt to the boom tube as shown inthe photo. Also shown is the completed welding on all front boom tubing joints.

Complete any leftover welding, and then clean up the welded areas. Your shor t wheelbase frame is now completed, andonly needs a steering system to be installed for test riding.

You will need to create a long gooseneck that will allow your handlebars to be placed in a comfortable position that willallow room for your knees to pass underneath. Handle bar position and style are a matter of personal preference, butyou will definitely need to extend a regular bicycle gooseneck to gain the height necessary to clear your knees. Find aset of handlebars you like and then sit on the bike, turning the cranks around while a helper takes a measurement fromthe handlebar center to the top of the head tube for you. Using this measurement, you can create the extendedgooseneck, using some bicycle frame tubing or electrical conduit as shown in the photo. Cut the clamp section from theoriginal steel gooseneck and then insert the new tube between the base and the clamp to create a new extendedgooseneck. Remember to also consider the angle of the extension tube in order to position your handlebars in the mostcomfortable position. You may need to tack weld and test, making slight adjustments in order to get the angle just theway you want it.


12/15

Once you have tack welded your extended gooseneck together and tested it on the bike, complete all the welding,making sure to weld the entire joint on both the top and bottom. Clean up and inspect your welding to ensure that thereare no gaps - you don't want your steering system to come apart during a ride!

Now that all of your frame and steering parts have been completely welded, you can prime and paint your new bike. Ialways use department store spray paint to complete a project, and if you take your time and follow the directions, youcan achieve a very good quality paint job for only a few dollars. Primer is first added and let to cure for a day or two sothat there is a good base coat for the paint to adhere to. Only a light sanding is necessary on bare or painted metal, justto remove any welding spatter or edges of old paint that remain. It is not necessary to spend days scraping every last bitof paint from the parts to be painted. Once the primer has had a day or two to cure, apply the spray paint, and againallow a day or two of curing before assembling the bike.


13/15

The completed SWB is shown here, fully painted and ready to ride. All bearing parts get a fresh coat of grease, and thechain is given a very light rubbing of oil. At this point, the seat has not been covered, but I ended up adding another 4inch top section as an upper back support.


14/15

A front and rear caliper brake were added, using the original parts from the donor bike. For more information oninstallation and adjustment of brakes and shifters, see the tutorial on our main page. Install all cables along the frameand avoid any tight bends so that the levers and shifters work with minimal friction. Brakes and derailleurs need to bealigned for optimal use, especially when taking them from one bike and putting them on another.


15/15

Besides the laid back seating position, riding a short wheelbase recumbent bike is virtually the same as any other

bicycle. Get onto the seat, place your best foot on the top of the cranks and then launch. If this is your first recumbentbike with pedals placed ahead of the front wheel then it may take some time to get used to the fact that your cranks staypointing forward during a turn. You may have the "wobbles" for the first few launches and corners, but after a few hoursthe bike will feel completely natural.

Recumbent bicycles offer an aerodynamic advantage over upright cycles due to the reduced frontal area hitting thewind. You also have a massive strength advantage as you can now deliver the full power of your legs directly into thecranks as your back is pushed into the seat. On an upright cycle, you can only deliver as much force as you weigh, andany more will just lift you off the seat. Having the cranks so high from the ground also means that you can blast intocorners without slowing down or worrying about where your pedals are. The only limitation on the corners will be yourtire traction and courage to take them at full speed.

Now that you have been bitten by the recumbent building bug, why not try a more advanced project, or try your ownmodifications to this one? Add an adjustable seat, a sliding bottom bracket, electric assist motor, or even a front fairing

to cheat the wind. The possibilities are only limited to how much time you have to spend at your workbench!

Simple SWB Recumbent

Documents

Transcript of Simple SWB Recumbent