Signal Relays AICOM - supply24.online
Transcript of Signal Relays AICOM - supply24.online
01-2016, Rev. 0116www.te.com© 2015 Tyco Electronics Corporation,a TE Connectivity Ltd. company
Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section.
Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.
1
AXICOMSignal Relays
IM Relay
n Slim line 10x6mm, low profile 5.65mm and min. board-space 60mm2
n Switching current 2/5A, switching power 60W/62.5VA and switching voltage 220VDC/250VAC
n Low coil power consumption, 140mW standard, 100mW for high sensitive version, 50mW for ultra high sensitive version and 100mW for bistable version
n High dielectric and surge capability up to 2500Vrms between open contacts and 2500Vrms between coil and contacts
n High mechanical shock resistance up to 50g functional
Typical applications Telecommunication, access and transmission equipment, optical network terminals, modems, office and business equipment, consumer electronics, measurement and test equipment, industrial control, medical equipment, HVAC
Approvals UL 508 File No. E 111441 Technical data of approved types on request
Contact Data standard, C D, I P standard and high high contact high dielectric current stability version version versionContact arrangement 2 form C, 2 CO Max. switching voltage 220VDC, 220VDC, 220VDC, 250VAC 250VAC 250VACRated current 2A 5A 2A Limiting continuous current 2A 5A 2ASwitching power 60W, 62.5VAContact material PdRu AgNi PdRu +Au +Au +Au covered covered covered Contact style twin cont. twin cont. twin cont. I: single contacts Minimum switching voltage 100µV Initial contact resistance <50mΩ at 10mA/30mV I: < 100mΩ Thermoelectric potential <10µVOperate time typ. 1ms, max. 3ms Release time without diode in parallel typ. 1ms, max. 3ms with diode in parallel typ. 3ms, max. 5ms Bounce time max. typ. 1ms, max. 5ms
Contact Data (continued)Electrical endurance at contact application 0 (≤30mV/≤10mA) min. 2.5x106 operations cable load open end min. 2.0x106 operations resistive, 125VDC / 0.24A - 30W min. 5x105 operations resistive, 220 VDC / 0.27A - 60W min. 1x105 operations resistive, 250VAC / 0.25A - 62.5VA min. 1x105 operations resistive, 30VDC / 1A - 30W min. 5x105 operations resistive, 30VDC / 2A - 60W min. 1x105 operationsUL contact rating 30VDC, 2A, 60W, NO only 110VDC, 0.3A, 33W 220VDC, 0.27A, 60W 125VAC, 0.5A, 62.5W 250VAC, 0.25A, 62.5W Mechanical endurance 108 operations
Coil Data Magnetic system monostable, bistable Coil voltage range 1.5 to 24VDC
Coil versions, standard version, monostable, 1 coil Coil Rated Operate Release Coil Rated coil code voltage voltage voltage resistance power VDC VDC VDC Ω±10% mW 00 1.5 1.13 0.15 16 140 08 2.4 1.80 0.24 41 140 01 3 2.25 0.30 64 140 02 4.5 3.38 0.45 145 140 03 5 3.75 0.50 178 140 04 6 4.50 0.60 257 140 05 9 6.75 0.90 579 140 06 12 9.00 1.20 1029 140 07 24 18.00 2.40 2880 200All figures are given for coil without pre-energization, at ambient temperature +23°C
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 21 of 28
AXICOMÊSignalÊRelays
IM Relay
Contact Data
IM-A IM-B IM-C IM-D IM-ENumber of contacts and type 1ÊPoleÊbreak 1ÊPoleÊmake 1ÊPoleÊÊ
changeover2ÊPoleÊbreak 2ÊPoleÊmake
Contact assembly BifurcatedÊcontactsContact material Palladium-ruthenium,Êgold-coveredLimiting continuous current at max. ambient temperature
2ÊA 2ÊA 4ÊA 2ÊA 2ÊA
Maximum switching current 2ÊA 2ÊA 3ÊA 2ÊA 2ÊAMaximum swichting voltage 220ÊVdc
250ÊVacMaximum switching capacity 60ÊW,Ê62.5ÊVAThermoelectric potential <Ê10ʵVMinimum switching voltage 100ʵVInitial contact resistance / measuring condition: 10 mA / 20 mV
< 100 mΩ < 100 mΩ NO < 100 mΩ < 50 mΩ < 50 mΩ
Electrical CC0 Contact category 0 endurance (≤ 30 mV / ≥ 10 mA) cable load open end
Resistive load at 125 Vdc / 0.24 A - 30 W at 220 Vdc / 0.27 A - 60 W at 250 Vac / 0.25 A - 62.5 VA at 30 Vdc / 1 A - 30 W at 30 Vdc / 2 A - 60 W
min.Ê2.5ÊxÊ106Êoperationsmin.Ê2.0ÊxÊ106Êoperations
min.Ê5ÊxÊ105Êoperationsmin.Ê1ÊxÊ105Êoperationsmin.Ê1ÊxÊ105Êoperationsmin.Ê5ÊxÊ105Êoperationsmin.Ê1ÊxÊ105Êoperations
Mechanical endurance typ.Ê108ÊoperationsUL contact ratings 220 Vdc / 0.24 A - 60 W
125 Vdc / 0.24 A - 30 W250 Vac / 0.25 A - 62.5 VA125 Vac / 0.5 A - 62.5 VA
30 Vdc / 2 A - 60 W
Max. DC Load Breaking Capacity
DC
Volta
ge [V
dc]
DC current [A]
resistive load
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 24 of 28
AXICOMÊSignalÊRelays
IM Relay
Coil Operating Range
Unom = Nominal coil voltageUmax. = Upper limit of the operative range of the coil voltage (limiting voltage) when coils are continously energizedUop. min. = Lower limit of the operative range of the coil voltage (reliable operate voltage) For latching relays Uset min. resp. Ureset min.Urel. min. = Lower limit of the operative range of the coil voltage (reliable release voltage)
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 10 0 1 10 12 0
Coi
l Vol
tage
[U/U
nom
]
Umax. at 0A
Umax. at 2x2A
Umax. at 2x1A
Unom. nominal coil voltage
Ambient Temperature [°C]
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120
Ambient Temperature [°C]
Coi
l Vol
tage
[U/U
nom]
Umax. at 0A
Umax. at 2x2A
Umax. at 2x1A
Unom. nominal coil voltage
Urel. min.
00.20.40.60.81
1.21.41.61.82
2.22.42.62.83
3.23.4
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140
Ambient Temperature [°C]
Coi
l Vol
tage
[U/U
nom]
Umax. - 5%coilduty at2x2A (100mW)
Umax.-5%coilduty at 0A(100mW)
Umax.-5%coilduty at 0A (200mW)
Umax. -5% coil duty at 2x1A (100mW)
Unom. nominal coil voltage
Umax. at 0A
140mW coil200mW coil
Urel. min.
50mW coil100mW coil
Uop min.
Umax. at 0A
Umax. - 100% coil duty at0A (100mW)
Umax. - 100% coil duty at0A (200mW)
Uset min.
100 mW Latching200 mW Latching
Coil operating range, standard version
Max. DC load breaking capacity
U
IM_
01-2016, Rev. 0116www.te.com© 2015 Tyco Electronics Corporation,a TE Connectivity Ltd. company
Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section.
Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.
2
AXICOMSignal Relays
IM Relay (Continued)
Insulation Data standard* C* D,P, I standard, high high current, sensitive, dielectric high contact ultra high version stability sensitive version versionInitial dielectric strength between open contacts 1000Vrms 1500Vrms 750Vrms between contact and coil 1800Vrms 1800Vrms 1500Vrms between adjacent contacts 1000Vrms 1800Vrms 750VrmsInitial surge withstand voltage between open contacts 1500V 2500V 1000V between contact and coil 2500V 2500V 2000V between adjacent contacts 1500V 2500V 1000VInitial insulation resistance between insulated elements >109Ω >109Ω >109ΩCapacitance between open contacts max. 1pF between contact and coil max. 2pF between adjacent contacts max. 2p
RF DataIsolation at 100MHz/900MHz 37.0dB/18.8dB Insertion loss at 100MHz/900MHz 0.03dB/0.33dB Voltage standing wave ratio (VSWR) at 100MHz/900MHz 1.06/1.49
Other Data Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content refer to the Product Compliance Support Center at www.te.com/customersupport/rohssupportcenterAmbient temperature -40°C to +85°C Thermal resistance <150K/W Category of environmental protection IEC 61810 RT V - hermetically sealed Vibration resistance (functional) 20g, 10 to 500Hz Shock resistance (functional), half sinus 11ms 50g Shock resistance (destructive), half sinus 0.5ms 500gMounting position any Weight max. 0.75gResistance to soldering heat SMT IEC 60068-2-58 Moisture sensitive level, JEDEC J-Std-020D MSL3 related only to SMT relays packed in orginal dry-packs Ultrasonic cleaning not recommendedPackaging/unit THT version tube/50pcs., box/1000 pcs. SMT version reel/1000 pcs., box/1000 or 5000 pcs.
Coil Data (continued)Coil versions, sensitive version, monostable, 1 coil Coil Rated Operate Release Coil Rated coil code voltage voltage voltage resistance power VDC VDC VDC Ω±10% mW 11 3 2.40 0.30 91 100 12 4.5 3.60 0.45 194 100 13 5 4.00 0.50 234 100 16 12 9.60 1.20 1315 110 17 24 19.20 2.40 4120 140Coil versions, ultra high sensitive version, monostable, 1 coil Coil Rated Operate Release Coil Rated coil code voltage voltage voltage resistance power VDC VDC VDC Ω±10% mW 21 3 2.55 0.30 180 50 22 4.5 3.83 0.45 405 50 23 5 4.25 0.50 500 50 26 12 10.20 1.20 2880 50All figures are given for coil without pre-energization, at ambient temperature +23°C
Coil versions, standard, bistable 1 coil Coil Rated Set Reset Coil Rated coil code voltage voltage voltage resistance power VDC VDC VDC Ω±10% mW 40 1.5 1.13 -1.13 23 100 48 2.4 1.80 -1.80 58 100 41 3 2.25 -2.25 90 100 42 4.5 3.38 -3.38 203 100 43 5 3.75 -3.75 250 100 44 6 4.50 -4.50 360 100 45 9 6.75 -6.75 810 100 46 12 9.00 -9.00 1440 100 47 24 18.00 -18.00 2880 200All figures are given for coil without pre-energization, at ambient temperature +23°C
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 24 of 28
AXICOMÊSignalÊRelays
IM Relay
Coil Operating Range
Unom = Nominal coil voltageUmax. = Upper limit of the operative range of the coil voltage (limiting voltage) when coils are continously energizedUop. min. = Lower limit of the operative range of the coil voltage (reliable operate voltage) For latching relays Uset min. resp. Ureset min.Urel. min. = Lower limit of the operative range of the coil voltage (reliable release voltage)
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 10 0 1 10 12 0
Coi
l Vol
tage
[U/U
nom
]
Umax. at 0A
Umax. at 2x2A
Umax. at 2x1A
Unom. nominal coil voltage
Ambient Temperature [°C]
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120
Ambient Temperature [°C]
Coi
l Vol
tage
[U/U
nom]
Umax. at 0A
Umax. at 2x2A
Umax. at 2x1A
Unom. nominal coil voltage
Urel. min.
00.20.40.60.81
1.21.41.61.82
2.22.42.62.83
3.23.4
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140
Ambient Temperature [°C]
Coi
l Vol
tage
[U/U
nom]
Umax. - 5%coilduty at2x2A (100mW)
Umax.-5%coilduty at 0A(100mW)
Umax.-5%coilduty at 0A (200mW)
Umax. -5% coil duty at 2x1A (100mW)
Unom. nominal coil voltage
Umax. at 0A
140mW coil200mW coil
Urel. min.
50mW coil100mW coil
Uop min.
Umax. at 0A
Umax. - 100% coil duty at0A (100mW)
Umax. - 100% coil duty at0A (200mW)
Uset min.
100 mW Latching200 mW Latching
Coil operating range, sensitive and ultra high sensitive coil
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 24 of 28
AXICOMÊSignalÊRelays
IM Relay
Coil Operating Range
Unom = Nominal coil voltageUmax. = Upper limit of the operative range of the coil voltage (limiting voltage) when coils are continously energizedUop. min. = Lower limit of the operative range of the coil voltage (reliable operate voltage) For latching relays Uset min. resp. Ureset min.Urel. min. = Lower limit of the operative range of the coil voltage (reliable release voltage)
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 10 0 1 10 12 0
Coi
l Vol
tage
[U/U
nom
]
Umax. at 0A
Umax. at 2x2A
Umax. at 2x1A
Unom. nominal coil voltage
Ambient Temperature [°C]
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120
Ambient Temperature [°C]
Coi
l Vol
tage
[U/U
nom]
Umax. at 0A
Umax. at 2x2A
Umax. at 2x1A
Unom. nominal coil voltage
Urel. min.
00.20.40.60.81
1.21.41.61.82
2.22.42.62.83
3.23.4
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140
Ambient Temperature [°C]
Coi
l Vol
tage
[U/U
nom]
Umax. - 5%coilduty at2x2A (100mW)
Umax.-5%coilduty at 0A(100mW)
Umax.-5%coilduty at 0A (200mW)
Umax. -5% coil duty at 2x1A (100mW)
Unom. nominal coil voltage
Umax. at 0A
140mW coil200mW coil
Urel. min.
50mW coil100mW coil
Uop min.
Umax. at 0A
Umax. - 100% coil duty at0A (100mW)
Umax. - 100% coil duty at0A (200mW)
Uset min.
100 mW Latching200 mW Latching
Coil operating range, bistable 1 coil
Monostable versionrest condition
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 28
AXICOMÊSignalÊRelays
IM Relay 2 Pole Changeover / 2 Form C / DPDT
Dimensions Dimensions in mm
THT Version
Mounting Hole Layout
View onto the component side of the PCB (top view)
Non-Latching Type
not energized condition
Latching Type, 1 Coil
reset condition
IMÊTHTStandard
IMÊTHTNarrow
IMÊSMTGullÊWings
IMÊSMTJ-Legs
mm inch mm inch mm inch mm inchLWH
10.00ʱÊ0.086.00ʱÊ0.085.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.085.70ʱÊ0.305.80ʱÊ0.08
0.393ʱÊ0.0030.224ʱÊ0.0120.230ʱÊ0.003
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.02
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
SMT VersionStandard Version Narrow Version
Solder Pad Layout
View onto the component side of the PCB (top view)
Gull Wings J-Legs
Standard Version Narrow Version Gull Wings
¯Êmin.Ê0.75 ¯Êmin.Ê0.75
Terminal Assignment
Relay – top view
ContactsÊ inÊ resetÊ position.Ê ContactÊpositionÊmightÊ changeÊduringÊ trans-portationÊ andÊ mustÊ beÊ resetÊ beforeÊuse.
Coplanarity ≤ 0.1mm Coplanarity ≤ 0.1mm
TT1T2D1D2TwS
3.2N/A
5.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.400.75
0.125N/A
0.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.029
3.2N/A
3.20ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.40.30ʱÊ0.05
0.125N/A
0.126ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.011ʱÊ0.002
N/A7.50ʱÊ0.305.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.295ʱÊ0.0110.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
N/A2.80ʱÊ0.205.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.110ʱÊ0.0070.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
10.0±0.08 6.0±0.08
5.08±0.1
0.43.
2±0.
15
2.2±
0.15
2.2±
0.15
3.2
5.65
-0.2
0.75
10.0±0.08 5.7±0.3
3.2±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.8±
0.08
0.3±
0.05
10.0±0.08 6.0±0.08
5.08±0.10.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
7.5±0.3
Coplanarity ≤0.1mm
2.8±0.2
Coplanarity ≤0.1mm
Terminal assignmentTOP view on relay
Bistable version, 1 coilreset condition
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 28
AXICOMÊSignalÊRelays
IM Relay 2 Pole Changeover / 2 Form C / DPDT
Dimensions Dimensions in mm
THT Version
Mounting Hole Layout
View onto the component side of the PCB (top view)
Non-Latching Type
not energized condition
Latching Type, 1 Coil
reset condition
IMÊTHTStandard
IMÊTHTNarrow
IMÊSMTGullÊWings
IMÊSMTJ-Legs
mm inch mm inch mm inch mm inchLWH
10.00ʱÊ0.086.00ʱÊ0.085.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.085.70ʱÊ0.305.80ʱÊ0.08
0.393ʱÊ0.0030.224ʱÊ0.0120.230ʱÊ0.003
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.02
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
SMT VersionStandard Version Narrow Version
Solder Pad Layout
View onto the component side of the PCB (top view)
Gull Wings J-Legs
Standard Version Narrow Version Gull Wings
¯Êmin.Ê0.75 ¯Êmin.Ê0.75
Terminal Assignment
Relay – top view
ContactsÊ inÊ resetÊ position.Ê ContactÊpositionÊmightÊ changeÊduringÊ trans-portationÊ andÊ mustÊ beÊ resetÊ beforeÊuse.
Coplanarity ≤ 0.1mm Coplanarity ≤ 0.1mm
TT1T2D1D2TwS
3.2N/A
5.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.400.75
0.125N/A
0.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.029
3.2N/A
3.20ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.40.30ʱÊ0.05
0.125N/A
0.126ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.011ʱÊ0.002
N/A7.50ʱÊ0.305.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.295ʱÊ0.0110.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
N/A2.80ʱÊ0.205.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.110ʱÊ0.0070.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.65
-0.2
0.75
10.0±0.08 5.7±0.3
3.2±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.8±
0.08
0.3±
0.05
10.0±0.08 6.0±0.08
5.08±0.10.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
7.5±0.3
Coplanarity ≤0.1mm
2.8±0.2
Coplanarity ≤0.1mm
Contacts are shown in reset condition. Contact position might change during transportation and must be reset before use.
*this relay contains SF6 (Sulfur hexafluoride, CAS number: 2551-62-4) for dielectric strength enhancement, SF6 is hermetically sealed in relay without leaks to air during normal applica-tion as recommended per the applicable product specification. It is clarified that the usage of SF6 in mini signal relay is not prohibited by related regulations. Please contact TE local sales or field engineer for further information and detailed material declaration.
01-2016, Rev. 0116www.te.com© 2015 Tyco Electronics Corporation,a TE Connectivity Ltd. company
Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section.
Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.
3
AXICOMSignal Relays
IM Relay (Continued)
THT version
Dimensions
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 28
AXICOMÊSignalÊRelays
IM Relay 2 Pole Changeover / 2 Form C / DPDT
Dimensions Dimensions in mm
THT Version
Mounting Hole Layout
View onto the component side of the PCB (top view)
Non-Latching Type
not energized condition
Latching Type, 1 Coil
reset condition
IMÊTHTStandard
IMÊTHTNarrow
IMÊSMTGullÊWings
IMÊSMTJ-Legs
mm inch mm inch mm inch mm inchLWH
10.00ʱÊ0.086.00ʱÊ0.085.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.085.70ʱÊ0.305.80ʱÊ0.08
0.393ʱÊ0.0030.224ʱÊ0.0120.230ʱÊ0.003
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.02
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
SMT VersionStandard Version Narrow Version
Solder Pad Layout
View onto the component side of the PCB (top view)
Gull Wings J-Legs
Standard Version Narrow Version Gull Wings
¯Êmin.Ê0.75 ¯Êmin.Ê0.75
Terminal Assignment
Relay – top view
ContactsÊ inÊ resetÊ position.Ê ContactÊpositionÊmightÊ changeÊduringÊ trans-portationÊ andÊ mustÊ beÊ resetÊ beforeÊuse.
Coplanarity ≤ 0.1mm Coplanarity ≤ 0.1mm
TT1T2D1D2TwS
3.2N/A
5.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.400.75
0.125N/A
0.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.029
3.2N/A
3.20ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.40.30ʱÊ0.05
0.125N/A
0.126ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.011ʱÊ0.002
N/A7.50ʱÊ0.305.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.295ʱÊ0.0110.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
N/A2.80ʱÊ0.205.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.110ʱÊ0.0070.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.65
-0.2
0.75
10.0±0.08 5.7±0.3
3.2±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.8±
0.08
0.3±
0.05
10.0±0.08 6.0±0.08
5.08±0.10.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
7.5±0.3
Coplanarity ≤0.1mm
2.8±0.2
Coplanarity ≤0.1mm
SMT version
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 28
AXICOMÊSignalÊRelays
IM Relay 2 Pole Changeover / 2 Form C / DPDT
Dimensions Dimensions in mm
THT Version
Mounting Hole Layout
View onto the component side of the PCB (top view)
Non-Latching Type
not energized condition
Latching Type, 1 Coil
reset condition
IMÊTHTStandard
IMÊTHTNarrow
IMÊSMTGullÊWings
IMÊSMTJ-Legs
mm inch mm inch mm inch mm inchLWH
10.00ʱÊ0.086.00ʱÊ0.085.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.085.70ʱÊ0.305.80ʱÊ0.08
0.393ʱÊ0.0030.224ʱÊ0.0120.230ʱÊ0.003
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.02
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
SMT VersionStandard Version Narrow Version
Solder Pad Layout
View onto the component side of the PCB (top view)
Gull Wings J-Legs
Standard Version Narrow Version Gull Wings
¯Êmin.Ê0.75 ¯Êmin.Ê0.75
Terminal Assignment
Relay – top view
ContactsÊ inÊ resetÊ position.Ê ContactÊpositionÊmightÊ changeÊduringÊ trans-portationÊ andÊ mustÊ beÊ resetÊ beforeÊuse.
Coplanarity ≤ 0.1mm Coplanarity ≤ 0.1mm
TT1T2D1D2TwS
3.2N/A
5.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.400.75
0.125N/A
0.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.029
3.2N/A
3.20ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.40.30ʱÊ0.05
0.125N/A
0.126ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.011ʱÊ0.002
N/A7.50ʱÊ0.305.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.295ʱÊ0.0110.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
N/A2.80ʱÊ0.205.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.110ʱÊ0.0070.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.65
-0.2
0.75
10.0±0.08 5.7±0.3
3.2±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.8±
0.08
0.3±
0.05
10.0±0.08 6.0±0.08
5.08±0.10.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
7.5±0.3
Coplanarity ≤0.1mm
2.8±0.2
Coplanarity ≤0.1mm
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 28
AXICOMÊSignalÊRelays
IM Relay 2 Pole Changeover / 2 Form C / DPDT
Dimensions Dimensions in mm
THT Version
Mounting Hole Layout
View onto the component side of the PCB (top view)
Non-Latching Type
not energized condition
Latching Type, 1 Coil
reset condition
IMÊTHTStandard
IMÊTHTNarrow
IMÊSMTGullÊWings
IMÊSMTJ-Legs
mm inch mm inch mm inch mm inchLWH
10.00ʱÊ0.086.00ʱÊ0.085.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.085.70ʱÊ0.305.80ʱÊ0.08
0.393ʱÊ0.0030.224ʱÊ0.0120.230ʱÊ0.003
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.02
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
SMT VersionStandard Version Narrow Version
Solder Pad Layout
View onto the component side of the PCB (top view)
Gull Wings J-Legs
Standard Version Narrow Version Gull Wings
¯Êmin.Ê0.75 ¯Êmin.Ê0.75
Terminal Assignment
Relay – top view
ContactsÊ inÊ resetÊ position.Ê ContactÊpositionÊmightÊ changeÊduringÊ trans-portationÊ andÊ mustÊ beÊ resetÊ beforeÊuse.
Coplanarity ≤ 0.1mm Coplanarity ≤ 0.1mm
TT1T2D1D2TwS
3.2N/A
5.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.400.75
0.125N/A
0.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.029
3.2N/A
3.20ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.40.30ʱÊ0.05
0.125N/A
0.126ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.011ʱÊ0.002
N/A7.50ʱÊ0.305.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.295ʱÊ0.0110.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
N/A2.80ʱÊ0.205.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.110ʱÊ0.0070.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.65
-0.2
0.75
10.0±0.08 5.7±0.3
3.2±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.8±
0.08
0.3±
0.05
10.0±0.08 6.0±0.08
5.08±0.10.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
7.5±0.3
Coplanarity ≤0.1mm
2.8±0.2
Coplanarity ≤0.1mm
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 28
AXICOMÊSignalÊRelays
IM Relay 2 Pole Changeover / 2 Form C / DPDT
Dimensions Dimensions in mm
THT Version
Mounting Hole Layout
View onto the component side of the PCB (top view)
Non-Latching Type
not energized condition
Latching Type, 1 Coil
reset condition
IMÊTHTStandard
IMÊTHTNarrow
IMÊSMTGullÊWings
IMÊSMTJ-Legs
mm inch mm inch mm inch mm inchLWH
10.00ʱÊ0.086.00ʱÊ0.085.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.085.70ʱÊ0.305.80ʱÊ0.08
0.393ʱÊ0.0030.224ʱÊ0.0120.230ʱÊ0.003
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.02
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
SMT VersionStandard Version Narrow Version
Solder Pad Layout
View onto the component side of the PCB (top view)
Gull Wings J-Legs
Standard Version Narrow Version Gull Wings
¯Êmin.Ê0.75 ¯Êmin.Ê0.75
Terminal Assignment
Relay – top view
ContactsÊ inÊ resetÊ position.Ê ContactÊpositionÊmightÊ changeÊduringÊ trans-portationÊ andÊ mustÊ beÊ resetÊ beforeÊuse.
Coplanarity ≤ 0.1mm Coplanarity ≤ 0.1mm
TT1T2D1D2TwS
3.2N/A
5.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.400.75
0.125N/A
0.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.029
3.2N/A
3.20ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.40.30ʱÊ0.05
0.125N/A
0.126ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.011ʱÊ0.002
N/A7.50ʱÊ0.305.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.295ʱÊ0.0110.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
N/A2.80ʱÊ0.205.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.110ʱÊ0.0070.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.65
-0.2
0.75
10.0±0.08 5.7±0.3
3.2±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.8±
0.08
0.3±
0.05
10.0±0.08 6.0±0.08
5.08±0.10.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
7.5±0.3
Coplanarity ≤0.1mm
2.8±0.2
Coplanarity ≤0.1mm
Standard version Narrow version Gull wings J-legs
PCB layout TOP view on component side of PCB
Standard version Narrow version Gull wings J-legs
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 28
AXICOMÊSignalÊRelays
IM Relay 2 Pole Changeover / 2 Form C / DPDT
Dimensions Dimensions in mm
THT Version
Mounting Hole Layout
View onto the component side of the PCB (top view)
Non-Latching Type
not energized condition
Latching Type, 1 Coil
reset condition
IMÊTHTStandard
IMÊTHTNarrow
IMÊSMTGullÊWings
IMÊSMTJ-Legs
mm inch mm inch mm inch mm inchLWH
10.00ʱÊ0.086.00ʱÊ0.085.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.085.70ʱÊ0.305.80ʱÊ0.08
0.393ʱÊ0.0030.224ʱÊ0.0120.230ʱÊ0.003
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.02
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
SMT VersionStandard Version Narrow Version
Solder Pad Layout
View onto the component side of the PCB (top view)
Gull Wings J-Legs
Standard Version Narrow Version Gull Wings
¯Êmin.Ê0.75 ¯Êmin.Ê0.75
Terminal Assignment
Relay – top view
ContactsÊ inÊ resetÊ position.Ê ContactÊpositionÊmightÊ changeÊduringÊ trans-portationÊ andÊ mustÊ beÊ resetÊ beforeÊuse.
Coplanarity ≤ 0.1mm Coplanarity ≤ 0.1mm
TT1T2D1D2TwS
3.2N/A
5.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.400.75
0.125N/A
0.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.029
3.2N/A
3.20ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.40.30ʱÊ0.05
0.125N/A
0.126ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.011ʱÊ0.002
N/A7.50ʱÊ0.305.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.295ʱÊ0.0110.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
N/A2.80ʱÊ0.205.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.110ʱÊ0.0070.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.65
-0.2
0.75
10.0±0.08 5.7±0.3
3.2±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.8±
0.08
0.3±
0.05
10.0±0.08 6.0±0.08
5.08±0.10.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
7.5±0.3
Coplanarity ≤0.1mm
2.8±0.2
Coplanarity ≤0.1mm
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 28
AXICOMÊSignalÊRelays
IM Relay 2 Pole Changeover / 2 Form C / DPDT
Dimensions Dimensions in mm
THT Version
Mounting Hole Layout
View onto the component side of the PCB (top view)
Non-Latching Type
not energized condition
Latching Type, 1 Coil
reset condition
IMÊTHTStandard
IMÊTHTNarrow
IMÊSMTGullÊWings
IMÊSMTJ-Legs
mm inch mm inch mm inch mm inchLWH
10.00ʱÊ0.086.00ʱÊ0.085.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.085.70ʱÊ0.305.80ʱÊ0.08
0.393ʱÊ0.0030.224ʱÊ0.0120.230ʱÊ0.003
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.02
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
SMT VersionStandard Version Narrow Version
Solder Pad Layout
View onto the component side of the PCB (top view)
Gull Wings J-Legs
Standard Version Narrow Version Gull Wings
¯Êmin.Ê0.75 ¯Êmin.Ê0.75
Terminal Assignment
Relay – top view
ContactsÊ inÊ resetÊ position.Ê ContactÊpositionÊmightÊ changeÊduringÊ trans-portationÊ andÊ mustÊ beÊ resetÊ beforeÊuse.
Coplanarity ≤ 0.1mm Coplanarity ≤ 0.1mm
TT1T2D1D2TwS
3.2N/A
5.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.400.75
0.125N/A
0.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.029
3.2N/A
3.20ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.40.30ʱÊ0.05
0.125N/A
0.126ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.011ʱÊ0.002
N/A7.50ʱÊ0.305.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.295ʱÊ0.0110.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
N/A2.80ʱÊ0.205.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.110ʱÊ0.0070.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.65
-0.2
0.75
10.0±0.08 5.7±0.3
3.2±0.1
0.43.
2±0.
15
2.2±
0.15
2.2±
0.15
3.2
5.8±
0.08
0.3±
0.05
10.0±0.08 6.0±0.08
5.08±0.10.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
7.5±0.3
Coplanarity ≤0.1mm
2.8±0.2
Coplanarity ≤0.1mm
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 28
AXICOMÊSignalÊRelays
IM Relay 2 Pole Changeover / 2 Form C / DPDT
Dimensions Dimensions in mm
THT Version
Mounting Hole Layout
View onto the component side of the PCB (top view)
Non-Latching Type
not energized condition
Latching Type, 1 Coil
reset condition
IMÊTHTStandard
IMÊTHTNarrow
IMÊSMTGullÊWings
IMÊSMTJ-Legs
mm inch mm inch mm inch mm inchLWH
10.00ʱÊ0.086.00ʱÊ0.085.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.085.70ʱÊ0.305.80ʱÊ0.08
0.393ʱÊ0.0030.224ʱÊ0.0120.230ʱÊ0.003
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.02
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
SMT VersionStandard Version Narrow Version
Solder Pad Layout
View onto the component side of the PCB (top view)
Gull Wings J-Legs
Standard Version Narrow Version Gull Wings
¯Êmin.Ê0.75 ¯Êmin.Ê0.75
Terminal Assignment
Relay – top view
ContactsÊ inÊ resetÊ position.Ê ContactÊpositionÊmightÊ changeÊduringÊ trans-portationÊ andÊ mustÊ beÊ resetÊ beforeÊuse.
Coplanarity ≤ 0.1mm Coplanarity ≤ 0.1mm
TT1T2D1D2TwS
3.2N/A
5.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.400.75
0.125N/A
0.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.029
3.2N/A
3.20ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.40.30ʱÊ0.05
0.125N/A
0.126ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.011ʱÊ0.002
N/A7.50ʱÊ0.305.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.295ʱÊ0.0110.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
N/A2.80ʱÊ0.205.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.110ʱÊ0.0070.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.65
-0.2
0.75
10.0±0.08 5.7±0.3
3.2±0.1
0.43.
2±0.
15
2.2±
0.15
2.2±
0.15
3.2
5.8±
0.08
0.3±
0.05
10.0±0.08 6.0±0.08
5.08±0.10.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
7.5±0.3
Coplanarity ≤0.1mm
2.8±0.2
Coplanarity ≤0.1mm
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 28
AXICOMÊSignalÊRelays
IM Relay 2 Pole Changeover / 2 Form C / DPDT
Dimensions Dimensions in mm
THT Version
Mounting Hole Layout
View onto the component side of the PCB (top view)
Non-Latching Type
not energized condition
Latching Type, 1 Coil
reset condition
IMÊTHTStandard
IMÊTHTNarrow
IMÊSMTGullÊWings
IMÊSMTJ-Legs
mm inch mm inch mm inch mm inchLWH
10.00ʱÊ0.086.00ʱÊ0.085.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.085.70ʱÊ0.305.80ʱÊ0.08
0.393ʱÊ0.0030.224ʱÊ0.0120.230ʱÊ0.003
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.20
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
10.00ʱÊ0.08ÊÊ6.00ʱÊ0.08ÊÊ5.65ÊÐÊ0.02
0.393ʱÊ0.0030.236ʱÊ0.0030.222ÊÐÊ0.008
SMT VersionStandard Version Narrow Version
Solder Pad Layout
View onto the component side of the PCB (top view)
Gull Wings J-Legs
Standard Version Narrow Version Gull Wings
¯Êmin.Ê0.75 ¯Êmin.Ê0.75
Terminal Assignment
Relay – top view
ContactsÊ inÊ resetÊ position.Ê ContactÊpositionÊmightÊ changeÊduringÊ trans-portationÊ andÊ mustÊ beÊ resetÊ beforeÊuse.
Coplanarity ≤ 0.1mm Coplanarity ≤ 0.1mm
TT1T2D1D2TwS
3.2N/A
5.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.400.75
0.125N/A
0.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.029
3.2N/A
3.20ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.40.30ʱÊ0.05
0.125N/A
0.126ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.0150.011ʱÊ0.002
N/A7.50ʱÊ0.305.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.295ʱÊ0.0110.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
N/A2.80ʱÊ0.205.08ʱÊ0.103.20ʱÊ0.152.20ʱÊ0.15
0.4N/A
N/A0.110ʱÊ0.0070.200ʱÊ0.0040.126ʱÊ0.0060.087ʱÊ0.006
0.015N/A
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.65
-0.2
0.75
10.0±0.08 5.7±0.3
3.2±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
3.2
5.8±
0.08
0.3±
0.05
10.0±0.08 6.0±0.08
5.08±0.10.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
10.0±0.08 6.0±0.08
5.08±0.1
0.4
3.2±
0.15
2.2±
0.15
2.2±
0.15
5.65
-0.2
7.5±0.3
Coplanarity ≤0.1mm
2.8±0.2
Coplanarity ≤0.1mm
Recommended soldering conditionsProcessing
Recommended reflow soldering profile IEC 61760-1
full line: typicaldotted line: process limits
external preheating
240°C
180°C
130°C
100°C
forced cooling
20 to 40s
Time [s]
Tem
per
atur
e [°
C]
Vapour phase solderingtemperature/time profile(lead and housing peak temp.)
Recommended soldering conditionsVapour phase soldering
Resistance to soldering heat - reflow profile IEC 60068-2-58
01-2016, Rev. 0116www.te.com© 2015 Tyco Electronics Corporation,a TE Connectivity Ltd. company
Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section.
Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.
4
AXICOMSignal Relays
IM Relay (Continued)
Packing
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 26 of 28
AXICOMÊSignalÊRelays
IM Relay
Packing Dimensions in mm
Reel Dimension
Tube for THT version 50 relays per tube 1,000 relays per box
Tape and reel for SMT version 1,000 relays per reel 1,000 or 5,000 relays per box
Tube for THT version50 relays per tube, 1000 relays per box
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 26 of 28
AXICOMÊSignalÊRelays
IM Relay
Packing Dimensions in mm
Reel Dimension
Tube for THT version 50 relays per tube 1,000 relays per box
Tape and reel for SMT version 1,000 relays per reel 1,000 or 5,000 relays per box
Tape and reel for SMT version1000 relays per reel, 1000 or 5000 relays per box
Reel dimensions
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 26 of 28
AXICOMÊSignalÊRelays
IM Relay
Packing Dimensions in mm
Reel Dimension
Tube for THT version 50 relays per tube 1,000 relays per box
Tape and reel for SMT version 1,000 relays per reel 1,000 or 5,000 relays per box
108-98001 Rev. M
All specifications subject to change. Consult Tyco Electronics for latest specifications. 26 of 28
AXICOMÊSignalÊRelays
IM Relay
Packing Dimensions in mm
Reel Dimension
Tube for THT version 50 relays per tube 1,000 relays per box
Tape and reel for SMT version 1,000 relays per reel 1,000 or 5,000 relays per box
Product code structure Typical product code IM 03 G R
Type IM Signal Relays IM SeriesContact arrangement Blank 2 form C, 2 COCoil Coil code: please refer to coil versions tablePerformance type Blank Standard version I High current version HVAC C High dielectric version D High current version P High contact stability versionTerminals T THT - standard J SMT - J-leg N THT - narrow version G SMT - gull wingPacking S Tube R Reel
01-2016, Rev. 0116www.te.com© 2015 Tyco Electronics Corporation,a TE Connectivity Ltd. company
Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section.
Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.
5
AXICOMSignal Relays
Product code Arrangement Perf. type Coil Coil type Coil Terminals Part numberIM00GR 2 form C, Standard 1.5VDC Monostable Standard SMT gull wing 3-1462037-7IM00JR 2 CO SMT J-leg 3-1462037-9IM00NS contacts THT narrow 1-1462038-0IM01GR 3VDC SMT gull wing 1462037-1IM01JR SMT J-leg 4-1462037-0IM01NS THT narrow 1-1462038-1IM01TS THT standard 1462037-4IM02GR 4.5VDC SMT gull wing 1462037-9IM02JR SMT J-leg 1-1462037-1IM02NS THT narrow 1-1462038-2IM03GR 5VDC SMT gull wing 1-1462037-4IM03JR SMT J-leg 1-1462037-6IM03NS THT narrow 1-1462038-3IM03TS THT standard 1-1462037-8IM04GR 6VDC SMT gull wing 4-1462037-2IM04JR SMT J-leg 4-1462037-4IM04NS THT narrow 1-1462038-4IM05GR 9VDC SMT gull wing 3-1462037-4IM05JR SMT J-leg 4-1462037-5IM05NS THT narrow 1-1462038-5IM05TS THT standard 2-1462037-2IM06GR 12VDC SMT gull wing 2-1462037-3IM06JR SMT J-leg 4-1462037-6IM06NS THT narrow 1-1462038-6IM07GR 24VDC SMT gull wing 4-1462037-7IM07JR SMT J-leg 4-1462037-8IM07NS THT narrow 1-1462038-7IM08GR 2.4VDC SMT gull wing 6-1462039-3IM11GR 3VDC High sens. 9-1462038-5IM12GR 4.5VDC 1462039-3IM13GR 5VDC 1462039-4IM16GR 12VDC 1462039-5IM17GR 24VDC 1462039-6IM17TS THT standard 4-1462039-6IM21GR 3VDC Ultra SMT gull wing 2-1462039-6IM21TS high THT standard 1-1462039-5IM22GR 4.5VDC sensitive SMT gull wing 2-1462039-7IM22TS THT standard 2-1462039-8IM23GR 5VDC SMT gull wing 2-1462039-9IM23TS THT standard 3-1462039-0IM26GR 12VDC SMT gull wing 3-1462039-1IM26TS THT standard 3-1462039-2IM40GR 1.5VDC Bistable Standard SMT gull wing 5-1462037-1IM40JR SMT J-leg 5-1462037-2IM40NS THT narrow 1-1462038-8IM40TS THT standard 5-1462037-0IM41GR 3VDC SMT gull wing 5-1462037-4IM41JR SMT J-leg 5-1462037-5IM41NS THT narrow 1-1462038-9IM41TS THT standard 5-1462037-3IM42GR 4.5VDC SMT gull wing 3-1462037-1IM42JR SMT J-leg 5-1462037-7IM42NS THT narrow 2-1462038-0IM42TS THT standard 5-1462037-6IM43GR 5VDC SMT gull wing 5-1462037-9IM43JR SMT J-leg 6-1462037-0IM43NS THT narrow 2-1462038-1IM43TS THT standard 5-1462037-8IM44GR 6VDC SMT gull wing 6-1462037-2IM44JR SMT J-leg 6-1462037-3IM44NS THT narrow 2-1462038-2IM44TS THT standard 6-1462037-1IM45GR 9VDC SMT gull wing 6-1462037-4IM45JR SMT J-leg 6-1462037-5IM45NS THT narrow 2-1462038-3IM46GR 12VDC SMT gull wing 6-1462037-7IM46JR SMT J-leg 6-1462037-8IM46NS THT narrow 2-1462038-4IM46TS THT standard 6-1462037-6IM47GR 24VDC SMT gull wing 7-1462037-0IM47JR SMT J-leg 7-1462037-1IM47NS THT narrow 2-1462038-5IM47TS THT standard 6-1462037-9IM48GR 2.4VDC SMT gull wing 1462039-8
Signal Relays
IM Relay (Continued)
01-2016, Rev. 0116www.te.com© 2015 Tyco Electronics Corporation,a TE Connectivity Ltd. company
Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section.
Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.
6
AXICOMSignal Relays
IM Relay (Continued)
Product code Arrangement Perf. type Coil Coil type Coil Terminals Part numberIM01CGR 2 form C High 3VDC Monostable Standard SMT gull wing 1462038-4IM01CTS 2 CO dielectric THT standard 9-1462038-6IM02CGR contacts 4.5VDC SMT gull wing 1462038-1IM03CGR 5VDC 1462038-2IM03CJR SMT J-leg 4-1462039-8IM03CTS THT standard 4-1462039-7IM05CGR 9VDC SMT gull wing 1462038-3IM06CGR 12VDC 9-1462037-9IM06CJR SMT J-leg 3-1462039-4IM06CTS THT standard 4-1462037-9IM07CGR 24VDC SMT gull wing 1462039-2IM07CTS THT standard 1462039-1IM17CGR High sens. SMT gull wing 1462039-7IM41CGR 3VDC Bistable Standard 4-1462039-2IM42CGR 4.5VDC 4-1462039-1IM43CGR 5VDC 9-1462038-7IM02DGR High 4.5VDC Monostable Standard 9-1462038-8IM03DGR current 5VDC 9-1462038-9IM03DJR SMT J-leg 3-1462039-3IM05DGR 9VDC SMT gull wing 1-1462039-7IM06DGR 12VDC 1-1462039-8IM06DJR SMT J-leg 7-1462039-0IM06DTS THT standard 3-1462039-8IM07DGR 24VDC SMT gull wing 3-1462039-7IM07DJR SMT J-leg 7-1462039-4IM07DTS THT standard 7-1462039-2IM22DTS 4.5VDC U.h.sens. 7-1462039-6IM41DGR 3VDC Bistable Standard SMT gull wing 6-1462039-8IM42DGR 4.5VDC 1-1462039-9IM42DNS THT narrow 1-1462039-6IM46DNS 12VDC 1-1462039-2IM47DJR 24VDC SMT J-leg 7-1462039-5IM48DGR 2.4VDC SMT gull wing 1462039-9IM49DGR 2VDC 2-1462039-2IM48IGR 2.4VDC 1462047-1IM49IGR 2VDC 1462047-4IM02PGR High 4.5VDC Monostable Standard 5-1462039-4IM02PNS contact THT narrow 5-1462039-8IM03PGR stability 5VDC SMT gull wing 5-1462039-5IM03PJR SMT J-leg 6-1462039-6IM03PNS THT narrow 5-1462039-9IM06PGR 12VDC SMT gull wing 5-1462039-6IM06PNS THT narrow 6-1462039-0IM42PGR 4.5VDC Bistable Standard SMT gull wing 5-1462039-7IM42PNS THT narrow 7-1462039-8IM43PGR SMT gull wing 7-1462039-3IM46PNS 12VDC THT narrow 6-1462039-1