Sienna Cotbed

Instruction Manual & User Guide Sienna Cotbed

An IGC Dorel brand

Please read this manual in its entirety before assembling the product and follow all instructions contained herein.

Please retain instruction manual for future reference.

Illustrations are representative only. Design and style may vary.

Instruction Manual & User Guide

2 – Sienna Cotbed – 11-09

Warnings These instructions detail the safe use, assembly and maintenance of your product. Please read these instructions

carefully and ensure that they are followed at all times.

• Follow manufacturer’s instructions at all times. Failure to follow these warnings and the instructions could result

in serious injury or death.

• Do not suspend strings, such as hood strings or pacifier cords, over a bassinette or cradle or attach strings to toys.

String can wrap around a child’s neck and choke them.

• To reduce the risks of Sudden Infant Death Syndrome (SIDS), pediatricians recommend healthy infants to be

placed on their backs to sleep – unless otherwise advised by your physician.

• Keep the bassinette clear of trailing cables or hanging cords.

• Never allow young children to play unsupervised in the vicinity of the bassinette.

• Stop using the bassinette when the infant begins to push up on hands and knees or when infant reaches a weight

of 10kg.

• Only use the mattress supplied with this bassinette. Never use an extra mattress as this may cause a child to

become trapped in the gap between the extra mattress, and the side of the cot, and suffocate.

• Never leave children unattended.

• Do not leave anything in the bassinette such as toys that provide a foothold to enable the child to climb out.

• Do not use the bassinette near naked heat sources, bar heaters, open fires or exposed flames. Do not leave the

bassinette outdoors exposed to direct sunlight.

• Keep the bassinette clear of trailing cables and hanging cords.

• Keep medication and small items that a child could choke on away from the bassinette.

• Before using the bassinette please check and ensure all top rails are locked securely.

• Do not place more than one child in the bassinette at the same time.

• Do not try and move the bassinette while a child is in it.

• Keep your fingers clear from corner joints and any moving parts when opening or folding the bassinette.

• This product is not intended for commercial use.

• Use only those accessories which are supplied by IGC Dorel and approved for use with the bassinette.

• To avoid danger of suffocation, keep any plastic bags away from babies and children. Plastic bags can block nose

and mouth and prevent breathing. Bags are not toys.


– Sienna Cotbed – 11-09 3

Component list

# Part Qty

1 Cot head

end 1

2 Cot foot

end 1

3 Long Bolt 8

# Part Qty

4 Short Bolt 8

5 Fixed cot

side 2

6 Mattress

base 1

7 Cot bed

support

bars

2

8 Barrel nut 8

9 Allen Key 1

Tools required - flat head screwdriver



Assembling your Sienna Cotbed We suggest that two people assemble the cot in the room in which it is to be used and to follow the

sequences as pictured. Unpack the cot carefully and unwrap each part taking care not to lose the

plastic bag of small items. Check the contents against the list of parts.

TO FIT THE COT SIDE • Turn cot head end (1) onto its side.

• Bring in the cot side (5), ensuring the

teething rail is at the top.

• Using two short bolts (4), fix the cot

side to the cot end using the allen key

(9) screwing through the top and

bottom holes on the inside of the cot

side.

• Ensuring the cot end is supported

repeat the process for the opposite cot

foot end (2). Leave the bolts loose.

TO FIT THE MATTRESS BASE When your child can sit up you must stop using the highest mattress base position!

The lowest mattress base position is the safest.

• You have three positions. Decide which mattress base position you require.

• With the cot still on its side, place the mattress base (6) in between the cot ends ensuring the holes for the barrel

nuts (8) are facing the underside of the cot.

• Using four long bolts (3) fix from the outside of the cot end into the barrel nuts using the allen key (9) as shown.

• Repeat with all four corners leaving the bolts loose.

To change the position of the mattress base simply follow the steps above.

To fix remaining cot side, repeat the process described in ‘To Fit the Cot Side’ above, with the

remaining fixed cot side (5), and tighten all bolts.



Assembling your Sienna Cotbed

TO CHANGE THE COT INTO A BED • Dismantle the cot following the previous steps in reverse, ensuring you keep all the bolts and barrel nuts in a safe

place.

• Separate the cot foot end (2) into two pieces as shown in diagram A.

• Turn the head end (1) onto its side as shown in diagram B. Attach one of the side support bars (7) using a long

bolt (3 ) ensuring that the barrel nut is inward facing in the position shown.

• Repeat the process for the foot end (2) leaving the bolts loose.

• Once the side support bars have been attached, fit the mattress base as shown and tighten all the bolts.



Notes



Product care and maintenance • Always store indoors in a clean dry place.

• Do not use abrasives or detergent on surfaces.

• Scuff marks can be removed with mild soap and warm water. Dry with soft towel.

• Occasional use of furniture polish will maintain the product’s finish.

• Regularly check all screws and fittings to ensure that they are tight.

• Damaged components should be replaced as required.

• Replacement parts are available from the IGC Customer Service Department.

Customer service Please contact our Customer Service Department if you experience a problem with this product or require assistance:

AUSTRALIAN CUSTOMERS

NEW ZEALAND CUSTOMERS

Email [email protected] [email protected]

Web www.igcdorel.com.au www.igcdorel.com.au

Phone 1 (03) 8311 5300 (09) 276 1040

Phone 2 1300 809 526 (local call cost) 0800 628 000 (Toll Free)

Hours 8:30 am – 4:30 pm, Monday to Friday 9:00 am – 4:00 pm, Monday to Friday

Postal IGC Dorel Pty Ltd P.O. Box 1260 Sunshine West, Victoria, 3020 Australia

IGC Dorel (New Zealand) P.O. Box 82377 Highland Park Mt Wellington New Zealand

Guarantee This product carries a twelve month guarantee to rectify manufacturing defects. It does not cover problems arising from

accidental damage or product misuse. Specifications are subject to change without notice.

Copy or reproduction without permission is prohibited.

© 2009 IGC Dorel Pty Ltd. All Rights Reserved. www.igcdorel.com.au

Sienna Cotbed

Documents

Transcript of Sienna Cotbed