SHORTFORM DATASHEET · Flex size: See [6 Mechanical Drawings] Host connectors: 10way FFC (FCI...
Transcript of SHORTFORM DATASHEET · Flex size: See [6 Mechanical Drawings] Host connectors: 10way FFC (FCI...
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 1 of 24
Consult TNx prior to design-in
Part of the
family of touchscreens
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 4 of 24
1 Highlights The Luminance family of multi-touch capacitive touch sensors and assemblies includes numerous models that have the following features:
Up to 12-bit XY multi-touch reporting
Supports up to 16 simultaneous touches
Reporting rate typically 80 to 100Hz depending on configuration
Suitable for lens thicknesses up to 4mm glass
Robust sensor design allows operation with a wide range of displays
Industry leading conducted and radiated immunity performance
Viewing area from 7” to 24” suitable for LCD modules from LG, Sharp, AUO,
Innolux etc.
Narrow edge margins, near invisible ITO pattern
FPC tail with driver PCB connects to host via low cost 10 way 1mm pitch ZIF
connector or USB Mini-B connector
I2C and USB communication interfaces with auto switch-over (link free)
Allows contemporary “bezel free” designs
Supported by TouchNetix’ proprietary TNxTouchHub tuning software for
Windows™
Optional adapter to allow “mouse mode” support in legacy O.S.s and embedded
versions of Windows™
3D CAD available on request1
Bare sensor supplied as 0.7mm thick glass substrate with bonded FPC and control
PCB connected via multi-way FPC connectors
Also available bonded to “standard” glass cover lens if required
Options for customizable cover lens subject to quantity
1 STEP file
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 5 of 24
2 Ordering Part Numbers
2.1 Touchscreen Assemblies2
Codename Nominal Diagonal
Touchscreen Assembly Part Number
Aspect Ratio
Standard lens
material EVK
Enki 7.0" TNxLM-070E-A7-AB-001rr 15:9 no lens TNxLM-EVK-070E-A7-AB-001rr
Enki 7.0" TNxLM-070E-A7-AB-002rr 15:9 3mm TNxLM-EVK-070E-A7-AB-002rr
Mata 8.4" TNxLM-084A-A7-AB-001rr 4:3 no lens TNxLM-EVK-084A-A7-AB-001rr
Mata 8.4" TNxLM-084A-A7-AB-002rr 4:3 3mm TNxLM-EVK-084A-A7-AB-002rr
Beli 10.1" TNxLM-101C-A7-AB-001rr 16:10 no lens TNxLM-EVK-101C-A7-AB-001rr
Beli 10.1" TNxLM-101C-A7-AB-002rr 16:10 3mm TNxLM-EVK-101C-A7-AB-002rr
Milu 10.4" TNxLM-104A-A7-AB-001rr 4:3 no lens TNxLM-EVK-104A-A7-AB-001rr
Milu 10.4" TNxLM-104A-A7-AB-002rr 4:3 3mm TNxLM-EVK-104A-A7-AB-002rr
Apis 12.1" TNxLM-121C-A7-AB-001rr 16:10 no lens TNxLM-EVK-121C-A7-AB-001rr
Apis 12.1" TNxLM-121C-A7-AB-002rr 16:10 3mm TNxLM-EVK-121C-A7-AB-002rr
Lado 12.1" TNxLM-121A-A7-AB-001rr 4:3 no lens TNxLM-EVK-121A-A7-AB-001rr
Lado 12.1" TNxLM-121A-A7-AB-002rr 4:3 3mm TNxLM-EVK-121A-A7-AB-002rr
Peko 12.3" TNxLM-123A-A7-AB-001rr 8:3 no lens TNxLM-EVK-123A-A7-AB-001rr
Peko 12.3" TNxLM-123A-A7-AB-002rr 8:3 3mm TNxLM-EVK-123A-A7-AB-002rr
Fudo 15.0" TNxLM-150A-A7-AB-001rr 4:3 no lens TNxLM-EVK-150A-A7-AB-001rr
Fudo 15.0" TNxLM-150A-A7-AB-002rr 4:3 3mm TNxLM-EVK-150A-A7-AB-002rr
Enyo 15.6" TNxLM-156B-A7-AB-001rr 16:9 no lens TNxLM-EVK-156B-A7-AB-001rr
Enyo 15.6" TNxLM-156B-A7-AB-002rr 16:9 3mm TNxLM-EVK-156B-A7-AB-002rr
Vali 18.5" TNxLM-185B-A7-AB-001rr 16:9 no lens TNxLM-EVK-185B-A7-AB-001rr
Vali 18.5" TNxLM-185B-A7-AB-002rr 16:9 3mm TNxLM-EVK-185B-A7-AB-002rr
Aray 19.0" TNxLM-190D-A7-AB-001rr 5:4 no lens TNxLM-EVK-190D-A7-AB-001rr
Aray 19.0" TNxLM-190D-A7-AB-002rr 5:4 3mm TNxLM-EVK-190D-A7-AB-002rr
Mars 21.5" TNxLM-215B-A7-AB-001rr 16:9 no lens TNxLM-EVK-215B-A7-AB-001rr
Mars 21.5" TNxLM-215B-A7-AB-002rr 16:9 3mm TNxLM-EVK-215B-A7-AB-002rr
Baku 24.0" TNxLM-240B-A7-AB-001rr 16:9 no lens TNxLM-EVK-240B-A7-AB-001rr
Baku 24.0" TNxLM-240B-A7-AB-002rr 16:9 3mm TNxLM-EVK-240B-A7-AB-002rr
Consult TNx non-listed sizes or for custom lens requirements.
2 Approximate dimensions and ratios
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 6 of 24
2.2 Optional Accessories
2.2.1 Mouse Mode USB Adapter Connects to the 10-way FFC connector on the sensor control PCB and outputs to a USB Mini-B receptacle. This allows the host to treat the touch panel as a Mouse HID device in either relative (touchpad) mode or absolute (digitizer style) mode. The board measures 32x30mm3.
2.2.2 EVK An evaluation kit is available for each model. See 2.1 for details of part numbers. Each kit contains the following items: 1x Sensor with lens as listed above 1x TNxAC-003 1x USB cable assembly 1x USB stick containing TNxTouchHub evaluation and tuning software for XP/Win7/8
3 Note that J1 (rectangular 5-way B2W connector) in the picture is an optional fit and is *not* populated by default.
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 7 of 24
3 Mechanical Specifications
3.1 Sensor Base material: Glass ITO. Interconnects in metal Thickness: 0.7mm typ. Dimensions: See Section [6 Mechanical Drawings] Transmissivity: 88% typ. non bonded sensor only Orientation: Suitable for portrait or landscape use Outline drawings: See Section [6 Mechanical Drawings] LCD attachment: Refer to [3.4 LCD Mounting] Attachment to housing: See “TNxAN00010 Recommended Attachment Methods for
Touchscreen Assemblies” Max lens thickness: 4mm glass, 2.5mm polycarbonate, 2mm acrylic Mass: Consult TNx Handling: Refer to “TNxAN00019 Glass Sensors”
3.2 Lens for 002 Variants Base material: Soda-lime glass Thickness: 3.0mm +/-0.2mm. Treatment: Chemically strengthened Decoration: Black4 border rear printed Outline drawing: See [6 Mechanical Drawings]
4 “Process black”
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 8 of 24
3.3 Controller PCB and FPC FPC position: Exits sensor at middle of bottom long edge Material: Polyimide FPC + epoxy-glass FR4 control PCB PCB size: 79.0 x 25.6 x 1mm Max component height: 3.9 mm above PCB top side Components: Top side of PCB only Flex size: See [6 Mechanical Drawings] Host connectors: 10way FFC (FCI SFW10R-4STxxLF or equivalent) top contact USB Mini-B receptacle Mounting: See “TNxAN00009 FPC Considerations for Touchscreen
Assemblies”. Rear side is suitable for adhesive tape mounting and is covered with solder resist but should not be assumed to be fully insulated
FPC Min bend radius R: R < 2mm not allowed 2 ≤ R < 2.5mm, 3 cycles max 2.5 ≤ R < 4mm, 10 cycles max R ≥ 4mm, 50 cycles max
Figure 3.3-1 Control Board Layout
3.4 LCD Mounting A customer LCD can be mounted to the rear of the sensor using an adhesive gasket5 using suitable pressure sensitive adhesive e.g. 3M VHB™ or equivalent6. The sensor is also suitable for full optical bond to the LCD using wet or dry adhesive. Contact TNx for guidance. See “TNxAN00010-A1 Recommended Attachment Methods for Touchscreen Assemblies”. It is strongly recommended that early testing with a target LCD is conducted to identify and incompatibilities with noisy LCD drive electronics7.
5 To be fitted by customer or as part of 3rd party “ moduler’s” responsibility 6 It is very important to conduct material compatibility trials for any adhesives that are in direct contact with any part of the sensor, unless they are already proven to be non-aggressors 7 The Luminance series is designed to repel most LCD noise but there are so many LCD variants with radically different levels of noise emitted, that pre-testing is advised.
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 19 of 24
6 Mechanical Drawings
6.1 Without Lens
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 20 of 24
Specific model dimensions in mm (all +/-0.5mm unless noted):
Codename Nominal Diagonal
Aspect Ratio
LCD-AA28 size Sensor size Sensor edge to LCD-AA
LONG AXIS
SHORT AXIS
LONG AXIS “A”
SHORT AXIS “B”
TOP “C”
BOTTOM “D”
(fpc edge)
LEFT & RIGHT
“E” Enki 7.0" 15:9 152.4 91.4 170.0 120.0 7.7 20.9 8.8 Mata 8.4" 4:3 170.4 127.8 184.0 149.4 4.7 16.9 6.8 Beli 10.1" 16:10 217.0 135.6 233.6 154.4 4.4 14.4 8.3 Milu 10.4" 4:3 211.2 158.4 233.0 188.7 7.6 22.7 10.9 Apis 12.1" 16:10 261.2 163.2 284.0 196.0 8.7 24.1 11.4 Lado 12.1" 4:3 245.8 184.3 268.0 216.8 8.5 24.0 11.1 Peko 12.3" 8:3 291.8 109.4 312.2 140.7 8.4 22.8 10.2 Enyo 15.6" 16:9 344.3 193.5 374.1 232.5 10.4 28.6 14.9 Fudo 15.0" 4:3 304.1 228.1 332.0 265.0 9.9 27.0 13.9 Vali 18.5" 16:9 409.7 230.4 440.5 271.0 11.2 29.4 15.4 Aray 19.0" 5:4 376.4 301.1 406.6 343.0 11.9 30.0 15.1 Mars 21.5" 16:9 475.2 267.3 500.0 306.0 11.2 27.5 12.4 Baku 24.0" 16:9 531.4 298.9 558.0 339.0 11.6 28.5 13.3
Table 6.1-1
28 AA means Active Area and is the zone occupied by the LCD pixels, but excluding the narrow black non-pixelated margin before reaching the LCD metal frame edges
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 21 of 24
Notes
1. The “Sensor size” defines the overall outside dimensions of the sensor glass. 2. Note that the FPC and Control Board lie centrally to the mid-line of the sensor in the long axis. 3. The rectangle shown on the drawing above representing the LCD-AA is a construction line for reference only. The transparent area of
the sensor is large enough to operate with a range of vendors’ LCDs for a given size (noting that there are sometimes subtle variations in the active and bezel region sizes between manufacturers for the “same” sized LCD modules). Please consult TNx for compatibility checks.
4. 3D Step data is available on request.
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 22 of 24
6.2 With Lens
Transparent
Black decoration
Decoration edge
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 23 of 24
Specific model dimensions in mm (all +/-0.5mm unless noted):
Codename Nominal Diagonal
Aspect Ratio
Lens size
LONG AXIS “A”
SHORT AXIS “B”
Enki 7.0" 15:9 194.0 144.0 Mata 8.4" 4:3 213.0 180.0 Beli 10.1" 16:10 257.6 178.4 Milu 10.4" 4:3 257.0 212.7 Apis 12.1" 16:10 308.0 220.0 Lado 12.1" 4:3 292.0 240.8 Peko 12.3" 8:3 336.2 164.7 Enyo 15.6" 16:9 398.1 256.5 Fudo 15.0" 4:3 356.0 289.0 Vali 18.5" 16:9 464.5 295.0 Aray 19.0" 5:4 430.6 367.0 Mars 21.5" 16:9 524.0 330.0 Baku 24.0" 16:9 582.0 363.0
Table 6.2-1
SHORTFORM DATASHEET
“Luminance” Datasheet
[TNxD00135-B4 Luminance Datasheet.docx] Confidential Page 24 of 24
Notes
1. All models: Dimension “F”: the lens is 12mm larger all round than the sensor (excluding corner radii). To compute the distance from Lens edge to LCD-AA, Dimensions C, D and E, simply add 12mm to Dimensions C, D and E from Table 6.1-1 “Sensor edge to LCD-AA”
2. All models: The lens decoration opening is 1mm larger all round than the LCD-AA 3. All models: The lens is 3mm nominal thickness with square ground edge and with nominal 0.5mm edge chamfers all round top and
bottom. 4. The Lens is bonded to the sensor with 0.5mm (+0.3/-0.2) optical adhesive. The adhesive may exceed the sensor glass profile by up to
1.0mm around its periphery. Take this into account when planning edge-bonded gaskets etc 5. Overall assembly thickness is 4.2mm (+0.55/-0.35) 6. See also 6.1 for sensor glass sizes for each model.
7. Note that the FPC and Control Board lie centrally to the mid-line of the sensor in the horizontal axis. 8. The rectangle shown on the drawing above representing the LCD-AA is a construction line for reference only. The transparent area of
the sensor is large enough to operate with a range of vendors’ LCDs for a given size (noting that there are sometimes subtle variations in the active and bezel region sizes between manufacturers for the “same” sized LCD modules). Please consult TNx for compatibility checks.
9. The black region of the lens (decoration region) is shown above “non-filled” for clarity, only the decoration inner edge is shown for reference. Note that due to the above noted manufacturer-to-manufacturer variations in size, the standard lenses offered may not be perfect for some LCD modules. Consult TNx for customized options.
10. 3D Step data is available on request.