Shear and Moment Diagrams
-
Upload
jeffrey-carlo-viduya-agliam -
Category
Documents
-
view
135 -
download
0
description
Transcript of Shear and Moment Diagrams
![Page 1: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/1.jpg)
1
Structural Axial, Shear and Bending Moments
Positive Internal Forces Acting on a Portal Frame
![Page 2: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/2.jpg)
2
Recall from mechanics of mater-ials that the internal forces P(generic axial), V (shear) and M(moment) represent resultants of the stress distribution acting on the cross section of the beam.
Internal Axial Force (P) ≡ equal in magnitude but opposite in direction to the algebraic sum (resultant) of the components in the direction parallel to the axis of the beam of all external loads and support reactions acting on either side of the section being considered.
T ≡ TensionC ≡ Compression
![Page 3: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/3.jpg)
3
Beam Sign Convention for Shear and Moment
![Page 4: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/4.jpg)
4
Internal Shear Force (V) ≡ equal in magnitude but opposite in direction to the algebraic sum (resultant) of the components in the direction perpendicular to the axis of the beam of all external loads and support reactions acting on either side of the section being considered.Internal Bending Moment (M) ≡equal in magnitude but opposite in direction to the algebraic sum of the moments about (the centroid of the cross section of the beam) the section of all external loads and support reactions acting on either side of the section being considered.
![Page 5: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/5.jpg)
5
Positive Sign Conventions:
Tension axial force on the section
Shears that produces clockwise moments
Bending moments that produce compression in the top fibers and tension in the bottom fibers of the beam
![Page 6: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/6.jpg)
6
Shear and bending moment diagrams depict the variation of these quantities along the length of the member.
Proceeding from one end of the member to the other, sections are passed. After each successive change in loading along the length of the member, a FBD(Free Body Diagram) is drawn to determine the equations express-ing the shear and bending mo-ment in terms of the distance from a convenient origin.Plotting these equations produces the shear and bending moment diagrams.
![Page 7: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/7.jpg)
7
V and M are in the opposite directions of the positive beam sign convention
![Page 8: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/8.jpg)
8
Shear and Bending Moment Diagrams
Zero ShearMaximumPositiveBendingMoment
⇒
![Page 9: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/9.jpg)
9
Principle of Superposition
![Page 10: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/10.jpg)
10
Example ProblemShear and Moment Diagrams
Calculate and draw the shear force and bending moment equations for the given structure.
![Page 11: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/11.jpg)
11
Sketching the Deflected Shape of a Beam or Frame
Qualitative Deflected Shape(elastic curve) ≡ a rough (usually exaggerated) sketch of the neutral surface of the structure in the deformed position under the action of a given loading condition.
Such sketches provide valuable insights into the behavior of struc-tures.
![Page 12: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/12.jpg)
12
Following our positive beam sign convention, a positive bending moment bends a beam concave upward (or toward the positive y direction), whereas a negative bending moment bends a beam concave downward (or towards the negative y direction).
![Page 13: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/13.jpg)
13
Point of Inflection
![Page 14: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/14.jpg)
14
An accurate sketch must satisfy the following rules:
• The curvature must be consis-tent with the moment curve.
• The deflected shape must satisfy the boundary constraints.
• The original angle at a rigid joint must be preserved.
• The length of the deformed member is the same as the original length of the unloaded member.
![Page 15: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/15.jpg)
15
•The horizontal projection of a beam or the vertical projection of a column is equal to the original length of the member.
•Axial deformations, which are trivial compared to bending deformations, are neglected.
![Page 16: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/16.jpg)
16
P.I. Point of Inflection= zero moment location
for mechanically loaded structures
≡
![Page 17: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/17.jpg)
17
BC = zero member bending
B C – straight line (linear) since MBC = 0
' '
![Page 18: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/18.jpg)
18
![Page 19: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/19.jpg)
19
Ignoring zero vertical displacement at C
Enforcing zero displacement at C
![Page 20: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/20.jpg)
20
Bending displacements without support conditions
![Page 21: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/21.jpg)
21
Enforcing support conditions
NOTE: Members AB’ and C’D”displacements are linear since the bending moment in these members is zero
DD” = DD’ + A’A from Fig. (a)
BB’ = CC’= A’A from Fig. (a)
![Page 22: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/22.jpg)
22
Note discontinuity in rotation at C – internal hinge location
![Page 23: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/23.jpg)
23
Axial Force, Shear Force and Bending Moment
Diagrams for Plane Frames
Previous definitions developed for shear forces and bending moments are valid for both beam and frame structures. However, application of these definitions, developed for a horizontal beam, to a frame structure will require some adjustments.
Consider the portal frame shown on the next two slides.
![Page 24: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/24.jpg)
24
P
q
A
B C
D
Figure F.1
(a) Loaded Portal Frame
![Page 25: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/25.jpg)
25
ABAV
ABAT
ABAM
ABBT
ABBV
ABBM
CDDT
CDDVCD
DM
CDCM
BCCMBC
BM
CDCT
BCCTBC
BT
CDCV
BCCVBC
BV
F.1 (b)
![Page 26: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/26.jpg)
26
The positive sign convention consistent with beam theory is shown in F.1(b). As seen from F.1 (b), the positive sign convention is (a) tension axial force, (b) shear forces that produce clockwise moments and (c) bending moments that result in tension stresses in the interior frame fibers.
The sign convention of F.1(b) can be seen to be equivalent to the beam sign convention rotating columns AB and CD to line up with beam BC.
![Page 27: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/27.jpg)
27
NOTE: For multi-bay frames, the usual practice is to define tension axial forces and shears that produce clockwise moments as positive for each member. However, the inside fiber for bending is not easily defined. Consequently, engineers choose to draw the bending moments on either the tension (common amongst structural engineers) or compression side of the members. They are not labeled as either positive or negative. Alternatively, a vector sign convention can be used – usual for computer codes.
![Page 28: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/28.jpg)
28
Example Frame Problem 1
Calculate and draw the axial force, shear force and bending moment equations for the given frame structure.
![Page 29: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/29.jpg)
29
Example Frame Problem 2
Calculate and draw the axial force, shear force and bending moment equations for the given frame structure.
![Page 30: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/30.jpg)
30
Two-Dimensional Force Transformations
xy
r
Px
Py
θ
Pn
Pt
FT (b)
FT (a)
FT = Force Transformation
![Page 31: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/31.jpg)
31
Suppose you are given the forces in FT (a) and you wish to transform these forces into Pn (normal) and Pt (tangential) as shown in FT (b). This force transformation may be neces-sary so that you can calculate the member axial and shear forces.
These force transformations are summarized on the next slide.
![Page 32: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/32.jpg)
32
Px
PyPn
θ
θ
n x yP P sin P cos= θ − θ
Py
Px
θ
Ptt x yP P cos P sin= θ + θ
x ycos ; sin ;r r
ytanx
θ = θ =
θ =
![Page 33: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/33.jpg)
33
Example Frame with Inclined Member
Calculate and draw the axial force, shear force and bending moment equations.
![Page 34: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/34.jpg)
34
Degree of Frame Indeterminacy
Rigid Frame ≡ composed of straight members connected either by rigid (moment resisting) connections or by hinged connections to form stable configurations.
Rigid Joint ≡ prevents relative translations and rotations between connected members.
![Page 35: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/35.jpg)
35
Statically Determinate ≡ the bending moments, shears, and axial forces in all its members, as well as the external reactions, can be determined by using the equations of equilibrium and condition, otherwise the frame is either unstable or statically indeterminate.
![Page 36: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/36.jpg)
36
Summary3m + R < 3j + C⇒ statically unstable frame
3m + R = 3j + C⇒ statically determinate
frame, if stable3m + R > 3j + C⇒ statically indeterminate
frame, if stable
I = (3m + R) - (3j + C) = degree of static
indeterminacy
Redundants ≡ excess members and reactions
![Page 37: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/37.jpg)
37
Alternative ApproachAn alternative approach for determining the degree of static indeterminacy of a frame is to cut enough members of the frame by passing imaginary sections and/or to remove enough supports to render the structure statically determinate. The total number of internal and external restraints thus removed equals the degree of static indeterminacy.
![Page 38: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/38.jpg)
38
This alternative approach pro-vides the most convenient means for determining the degree of static indeterminacy of multistory building frames:
I = 3(Ng – Nf) – Nh – 2Nr – C
Ng ≡ Number of Girders in thestructure
Nf ≡ Number of Free joints in the structure
Nh ≡ Number of Hinged supports
Nr ≡ Number of Roller supports
C ≡ Number of equations of Condition in the structure
![Page 39: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/39.jpg)
39
Equations of Condition at a Joint Detail w/ Three or More Members
Cj = Nbj – 1
Nbj = Number of Beam (moment resisting) members at joint j
![Page 40: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/40.jpg)
40
m = 5, R = 8j = 6, C = 0
I = 5
m = 4, R = 3j = 4, C = 0
I = 3
m = 6, R = 4j = 6, C = 0
I = 4
I = (3m + R) – (3j + C)
![Page 41: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/41.jpg)
41
m = 10, R = 9j = 9, C = 5
Ng = 4, Nf = 0Nh = Nr = 0
I = 7
Ng = 4, Nf = 0Nh = Nr = 0
C = 0I = 12
I = 3(Ng – Nf) – Nh – 2Nr - C
![Page 42: Shear and Moment Diagrams](https://reader033.fdocuments.us/reader033/viewer/2022042512/55cf9d77550346d033adbe28/html5/thumbnails/42.jpg)
42
Ng = 35, Nf = 0Nh = Nr = 0
C = 0I = 105