Sharp XEA101 Electronic Cash Register Sm
-
Upload
doru-razvan -
Category
Documents
-
view
37 -
download
6
Transcript of Sharp XEA101 Electronic Cash Register Sm
ELECTRONICCASH REGISTER
MODEL XE-A101SRV KEY : Not necessaryPRINTER : M-31(U and A version)
CHAPTER 1. SPECIFICATIONS ..................................................................... 1
CHAPTER 2. OPTIONS ................................................................................... 4
CHAPTER 3. MASTER RESET ....................................................................... 4
CHAPTER 4. HARDWARE DESCRIPTION..................................................... 5
CHAPTER 5. TEST FUNCTION....................................................................... 8
CHAPTER 6. SERVICE PRECAUTION......................................................... 10
CHAPTER 7. CIRCUIT DIAGRAM AND PWB LAYOUT................................ 11
PARTS GUIDE
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specifiedones for maintaining the safety and performance of the set.
SHARP CORPORATIONThis document has been published to be used for after sales service only.The contents are subject to change without notice.
SERVICE MANUAL
CHAPTER 1. SPECIFICATIONS
1. APPEARANCE
Front view
2. RATING
Weight Approx 5.0kg
External dimension(Including the drawer)
330 (W) x 363 (D) x 253 (H) mm13 (W) x 14.3 (D) x 9.96 (H) inches
Power source AC 120V ( 10%), 60Hz
Power consumption Stand-by 4WOperating 12.5W
Working temperature 0~40°C (32 to 104°F)
3. KEYBOARD
1) KEYBOARD LAYOUT
Type Normal keyboard
Key position STD/MAX 30
Key pitch 19 (W) x 19 (H) mm
Key layout Fixed type
2) KEY LIST
Keytop Description
0-9,00 Numeric keys
CL Clear key
@/TM Multiplication & Time display key
Paper feed key
Tax 1 Shift/RA Tax 1 shift and Received on account key
Tax 2 Shift/PO Tax 2 shift and Paid out key
% Percent keys
ESC Error escape key
VOID Void key
CLK# Clerk code Entry key
PLU PLU code entry key
SHIFT Department shift key
#/SBTL Non-add code & Tax Included subtotal key
CHK Check key
CH Charge key
CA/AT/NS Cash sale Amount tender and No Sale key
Dept1-8 Department key
4. MODE SWITCH
1) LAYOUT• Slid type
5. DISPLAY
1) OPERATOR DISPLAYDisplay device: LED numeric display
Number of line: 1 line
Number of positions: 8 positions numeric display
Color of display: Yellow / Green
Character size: Numeric 14 (H) x 8 (W) mm
(Layout)
Display
Drawer
Drawer lock
Keyboard
Printer cover
Mode switch
@/TMTAX1SHIFT
/RA
TAX2SHIFT
/PO
VOID
SHIFT PLU
ESC
%
37
26
15
48
CHK CLK#
#/SBTL
CH
CA/AT/NS
REGX/F
Z/PGM
VOIDOFF
PLU code
Repeat
Department code
>>>>> USE FONT <<<<<
Helvetica/ Helvetica-Condensed/ Century-Schoolbook/ Symbol & OriginalFonts: (RingWorld2/RingFont2/Pa
Symbol/PartsCod)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
2) DISPLAY CONTENTSDepartments/PLU Code:
The department code or PLU code entered appears on the left.For example, if the key for department 1 is pressed, "1" would ap-pear in the extreme left position.
Repeat:
Indicates the number of times the same department key ispressed. If an entry is repeated more than ten times, only the firstdigit is displayed (12 displays as "2").
(E) Error:
This symbol appears, accompanied by a warning beep, when anerror is made. If this occurs during a transaction because of an ex-cessive digit entry, simply press CL and re-enter correctly.
(P) Program:
This symbol remains on the display when the cash register is be-ing programmed in the Z/PGM mode.
(F) Finalization:
This symbol appears when a transaction is finalized by pressing CA/AT/NS , CH or CHK .
(o) Subtotal:
This symbol appears when #/SBTL is pressed and the cashregister computes the subtotal, and also when the amount ten-dered is less than the total sale amount.
(C) Change:
This symbol appears whenever the change due amount is dis-played.
(L) Low battery:
This symbol appears when the power of the installed batteries isbelow a certain level or you need to replace the batteries withnew ones. (see the "Maintenance" section for explanation.)
(L) No battery:
This symbol appears when no batteries are installed. (see "Main-tenance" and "Getting Started" sections for explanation.)
In addition, the following appear when appropriate:
• The minus sign (-) can appear in positions 2 to 8.
• The decimal point appears in positions 1 to 3.
• When entry of the secret code is necessary, "---"appears in posi-tions 1 to 4.
6. PRINTER
1) PRINTER• Model name: M-31
• No. of stations: 1
• Printing system: Print wheel selective type
• Printing capacity: max. 13 characters
• Character size: 1.6mm (W) x 2.8mm (H)
• Print pitch: Column distance 2.1mm (numeric to numeric),2.6mm (numeric to symbol)
Row distance 4.6mm
• Print speed: Approximate 1.4 lines/s (6 digits/line)
• Paper feed speed: Approximate 4.3 lines/s
• Reliability: MCBF 0.3 million lines
2) PAPER• Paper roll dimension: 57.5 0.5mm
max. 80mm in diameter
• Paper quality: Bond paper (paper thickness: 0.06 to0.085mm paper weight: 47 to 64g/m2)
3) INKING• Ink supply system: Ink rill
• From: Roller
• Specification: Material - rubber
• Ribbon life: 0.7 million characters
• Print color: purple
4) LOGO STAMP (No)
5) CUTTER• Manual cutter
6) PRINTING WHEEL LAYOUT
1
2
3
4
5
6
7
8
9
10
11
12
13
0
1 2 3 4 5 6 7 8 9 10 11 12
#
13
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
CG
Z
RA
PO
VD
%
@
ST
TX
CA
X
CK
CH
7. DRAWER
[OUTLINE]• Standard equipment: Yes (1)• Max. number of drawers: 1• The drawer consists of:
(1) Drawer box (outer case) and drawer(2) Money case(3) Coin case(4) Lock (attached to the drawer)
[SPECIFICATION]
1) DRAWER BOX AND DRAWER
Size 330 (W) x 363 (D) x 98 (H) mm13 (W) x 14.3 (D) x 3.9 (H) inches
Material PlasticBell –Release lever Standard equipment: situated at the bottomDrawer open sensor –
2) MONEY CASE
Separation from the drawer DisallowedSeparation of the bill compartments from the coincompartments
Allowed
Bill separator –Number of compartments 4B/5C
Layout:
3) LOCK (LOCK KEY : LKGIM7331BHZZ)• Location of the lock: Front• Method of locking and unlocking:
To lock, insert the drawer lock key into thelock and turn it 90 degrees counter clockwise.To unlock, insert the drawer lock key and turnit 90 degrees clockwise.
• Key No: SK1-1
8. BATTERY
1) MEMORY BACK UP BATTERYFor memory back up, the dry battery ULM-3 (3 pieces) are needed.
1. Memory holding time:Approx. 1 year after New dry batteries are installed.
2. Battery exchange method:When the low battery symbol "L" lights up, replace the batteries (3AA) replaced by the following method;1) Power on the ECR.2) Mode switch turn to "REG" mode.3) Remove the OLD dry batteries (3 pieces).4) Insert the NEW dry batteries (3 pieces).5) Confirm the low battery symbol "L" is off.
2) LOW BATTERYLow battery indication will appear on the left side of display when thebattery voltage is low.
CASE 1: When sitting idle or after completion of transaction.
The machine can indicate the low battery condition (Always)
CASE 2: Low battery indication will not appear during key opera-tions, but will appear after power up of the cash register.
[Display sample]" 0.00" : Battery is OK."L 0.00" : Low battery (You have to change the batteries.)
After finalization"F 12.34" : Battery is OK."L 12.34" : Low battery ("L" indicate instead of "F".)
3) NO BATTERYIf the user forgets to replace the battery and the battery voltage fallsbelow a certain level, or if a power failure occurs with no batteriesinstalled, the memory contents cannot be retained. The CPU judges itas no battery and performs the master reset. In this case, all thesettings and registrations are cleared. If, however, the power is con-tinuously supplied to the AC cord, the memory contents are retained.
Low battery : Batteries are installed, but the voltage is low.Memory back up can be done.
No battery : Batteries are not installed or the voltage is extremelylow.The master reset is executed when a power failureoccurs, when the batteries are not properly charged.
Low battery & No battery indication will appear at the most left posi-tion of display when the battery voltage is low.
CASE 1: When any numeric entry & item entry is not done or justafter finalization.
The machine can indicate the battery condition. (Always)
CASE 2: When numeric entry or item entry is done.
Battery condition is not appeared.Exceptionally, at the power is restored after power failure, thelow battery & No battery indication will appear on the displayonly when the battery voltage is low.And the indication will disappear after any key entry.
[Display sample]" 0.00" : Battery is OK."L 0.00" : Low battery"L 0.00" : No batteryAfter finalization
"F 12.34" : Battery is OK."L 12.34" : Low battery ("L" indicate instead of "F".)"L 12.34" : No battery ("L" indicate instead of "F".)
4B/5C
L L
CHAPTER 2. OPTIONS
1. OPTIONS (No)
2. SERVICE OPTIONS (No)
3. SUPPLIES
NO NAME PARTS CODE PRICE RANK DESCRIPTION
1 ROLL PAPER AS 5 ROLLS/PACK
2 INK ROLLER AF
4 SPECIAL SERVICE TOOLS (No)
CHAPTER 3. MASTER RESET
Master reset: Clears all the memory and initializes each preset pa-rameter.
The master reset should be performed by using the following proce-dure.
1. Turn off the power (Power OFF). (See Note 1.)
2. Let the ECR be without the memory back up battery.
3. Turn the mode switch to the others of Power-off position.
4. Turn on the power (Power ON). (See Note 2.)
When the master rest is completed, the buzzer sounds intermittentlythree times.
5. Attach the memory back up battery to the ECR.
The master reset can also be accomplished in the following case.(See Note 3.)
Note 1) Power OFF: Means disconnecting the AC power supply tothe machine.(Specifically, unplugging the machine.)
Note 2) Power ON: Means connecting the AC power to the ma-chine.(Specifically, plugging in the machine.)
Note 3) In case a power failure occurs when the machine has nobattery installed, the master reset operation is automaticallyperformed after the power has been restored.
CHAPTER 4. HARDWARE DESCRIPTION
1. OUTLINE
• CPU: uPD780023A (ROM 24KB, RAM 1024B)
• KEY BOARD: 30key including PF key
• MODE SW: 5position slide SW
DISPLAY: 7seg.+DP x 8digit LED (YELLOW GREEN) FRONT only
• DRAWER: 1ch, no open sensor
• BUZZER: 1beep, piezo buzzer
• PRINTER: M-31(no EURO SYMBOL)
2. BLOCK DIAGRAM
3. DISCRIPTION
1) DISPLAY
(Output Timing of STROBE signal)
2) KEYBOARD and MODE SWMODE SW, KEY MATRIX is follows.
Note: Although the XE-A101 has 30 keys, the keyboard circuit isactually 32 keys (+) the PF key.
3) BUZZERThe BUZZER is driven by the P75/BUZ signal of the CPU.
Frequency : 4.095kHz
6V
CPU
uPD780023A
D
PrinterM-31
RAWER
KE Y
BOARD
&
MODE SW
8. 8. 8. 8. 8. 8. 8.
FRONT display :8digit
POWER
SUPPLY
AC 5V
ST1- ST4-,ST5
A1 G1,DP1,A2 G2~ ,DP2
KST1 KST8
KR1 KR6
8.
BU ZZER
MA IN
4.19MHz
For Clock
32.768kHz
Battery
5V
ST4- ST3- ST2- ST1-
ST1-
ST2-
ST3-
ST4-
1ms
30~100us
Displaystrobe
1 2 3 4 5
SLIDE SW
REG
POWEROFF
VOID X/F Z/PGM
22
31 7
15 16
24 25
26 1 2
8 9 10
17 18 19
27 28
3 4
11 12
21
30
5 6
13 14
32
SW1
MODE SW
KST2
KR1
KST3
KST4
KST5
1
2
3
4
5
6 7 13 25D13 1SS133 KST1
1 2 8 14D14 1SS133 KST2
11 12 19 9D15 1SS133 KST3
17 18 3 23D16 1SS133 KST4
28 24 20 10D17 1SS133 KST5
30 26 21 4D18 1SS133 KST6
32 22 15 5D19 1SS133 KST7
29 31 27 16D20 1SS133 KST8
KST1
1
2
3
4
5
6
7
8
9
KCN2
KR2 KR6 KR5 KR4 KR3
KEYBOARD
4) REWIND MOTORWhen the rewind motor is driven by the signal of the CPU.
5) DRAWERDRAWER OPEN signal :Output high signal between 50ms
6) DETECTING "LOW VOLTAGE"• Values obtained by AD conversion and averaging
Register value: 138 ( 2.7V) or less No voltage139 - 154 ( 2.7V - 3.0V) Low voltagemore than 154 OK
7) DESTINATION DETECTION port
U and A version
P66 L
5ms 10ms 15ms
PRINTER MOTOR
REWINDMOTOR
4. CPU PORT TABLE
No. PIN Name Signal Name Description Output/Input Initial state When STBY1 P50/A8 RWND REWIND MOTOR O L O/L2 P51/A9 DR To DRAWER O L O/L3 P52/A10 SA2 DISPLAY SEGMENT O L O/L4 P53/A11 SB2 DISPLAY SEGMENT O L O/L5 P54/A12 SC2 DISPLAY SEGMENT O L O/L6 P55/A13 SD2 DISPLAY SEGMENT O L O/L7 P56/A14 SE2 DISPLAY SEGMENT O L O/L8 P57/A15 SF2 DISPLAY SEGMENT O L O/L9 Vss0 GND
10 Vdd0 VDD11 P30 ST1- DISPLAY STROBE N-Ch O.D. O H I12 P31 ST2- DISPLAY STROBE N-Ch O.D. O H I13 P32 ST3- DISPLAY STROBE N-Ch O.D. O H I14 P33 ST4- DISPLAY STROBE N-Ch O.D. O H I15 P34/SI31 ST5 DISPLAY STROBE (H ACTIVE) O L O/L16 P35/SO31 NU (GND via 56k) I I17 P36/SCK31- NU (GND via 56k) I I18 P20/SI30 SA1 DISPLAY SEGMENT O L O/L19 P21/SO30 SB1 DISPLAY SEGMENT O L O/L20 P22/SCK30- SC1 DISPLAY SEGMENT O L O/L21 P23/RXD0 SD1 DISPLAY SEGMENT O L O/L22 P24/TXD0 SE1 DISPLAY SEGMENT O L O/L23 P25/ASCK0 SF1 DISPLAY SEGMENT O L O/L24 Vdd1 VDD25 Avss GND26 P17/ANI7 VBAT BATTERY voltage I I27 P16/ANI6 NU RESERVE FOR KEY RETURN I I28 P15/ANI5 KR6 KEY RETURN I I29 P14/ANI4 KR5 KEY RETURN I I30 P13/ANI3 KR4 KEY RETURN I I31 P12/ANI2 KR3 KEY RETURN I I32 P11/ANI1 KR2 KEY RETURN I I33 P10/ANI0 KR1 KEY RETURN I I34 Avref VCC35 Avdd VDD36 RESET- RESET-37 XT2 XT2 32.768Khz Xtal38 XT1 XT1 32.768Khz Xtal39 IC/VPP GND40 X2 X2 SYSTEM CLOCK41 X1 X1 SYSTEM CLOCK42 Vss1 GND43 P00/INTP0 /POF POWER OFF I I44 P01/INTP1 T From PRINTER I I45 P02/INTP2 t From PRINTER I I46 P03/INTP3/ADTRG R From PRINTER I I47 P70/TI00/TO0 SG1 DISPLAY SEGMENT O L O/L48 P71/TI01 SDP1 DISPLAY SEGMENT O L O/L49 P72/TI50/TO50 SG2 DISPLAY SEGMENT O L O/L50 P73/TI51/TO51 SDP2 DISPLAY SEGMENT O L O/L51 P74/PCL NU O L O/L52 P75/BUZ BUZ BUZZER O L O/L53 P64/RD- MTR To PRINTER O L O/L54 P65/WR- TRG To PRINTER O L O/L55 P66/WAIT- MSL1 MODEL SELECT1 I I56 P67/ASTB MSL2 MODEL SELECT2 I I57 P40/AD0 KST1 KEY STROBE O L O/L58 P41/AD1 KST2 KEY STROBE O L O/L59 P42/AD2 KST3 KEY STROBE O L O/L60 P43/AD3 KST4 KEY STROBE O L O/L61 P44/AD4 KST5 KEY STROBE O L O/L62 P45/AD5 KST6 KEY STROBE O L O/L63 P46/AD6 KST7 KEY STROBE O L O/L64 P47/AD7 KST8 KEY STROBE O L O/L
CHAPTER 5.TEST FUNCTION
1) To execute the diag test, set the mode switch to Z/PGM. Enter thedesired JOB code, and press the PO (paid out) key.
2) The test message is printed by the printer.
3) Test contents and key operations.
NO. Test contents Key operations
1 Mode switch test
2 Key test
3 Display buzzer test
4 Drawer test
5 Printer test
6 CPU version NO. print
7 Battery level test
8 Time display test
9 Destination display
1. MODE SWITCH TEST
1) KEY OPERATION
2) TEST PROCEDUREChange over the mode switch as follows. If the mode switch data inthe proper sequence is not read with the above operation, an error isprinted.
To cancel this test mode, set the mode switch to any a position otherthan Z/PGM to Z/PGM. In this case, the completion print is performed.
During the test , the display indicates hard codes which correspond tothe switch positions.
3) MODE SWITCH OPERATION
Completion print 01Error print – – – 01
2. KEY TEST
1) KEY OPERATION
2) TEST PROCEDUREPerform the keyboard check with the sum check data of the key code.
Enter the sum check data of each model in the four digits precedingthe diag number 02, and compare the data with the key position codewhich is added until the CA/AT/NS key is pressed.
If the data coincides with the code, the completion print is performed.If not, the error print is performed.
Completion print 02Error print – – – 02
XXXX Sum data
3. DISPLAY BUZZER TEST
1) KEY OPERATION
2) TEST PROCEDURECheck the continuous buzzer sound and the display state.
Display state:
8. 7. 6. 5. 4. 3. 2. 1.
The decimal point will shift from the lower digit to the upper, step bystep (500mSEC). To cancel the test mode, press any key, and thebuzzer will stop and the completion print is performed.
Completion print 03
4. DRAWER TEST
1) KEY OPERATION
2) TEST PROCEDUREThe drawer opens with the above key operation. Check that thedrawer is open. Press any key to terminate the test.
Completion print 04
PO1
PO02
PO3
PO4
PO5
PO6
PO7
PO8
PO9
PO1
Mode:
Display: (01)(02)
X/FLASH
(03)
Z/PGM
(04)
OFFVOID REG
PO02
PO3
PO4
5. PRINTER TEST
1) KEY OPERATION
2) TEST PROCEDUREWith the above key operation , the print test pattern is repeatedlyprinted.
Pressing any key will terminate the test after the completion of onecycle print. (The receipt is issued at the end.)
6. CPU VERSION NO. PRINT
1) KEY OPERATION
2) DESCRIPTIONThe CPU version No. are printed with above key operation.(Print example)
0101 CPU version NO.06
This test is terminated when printing is completed.
7. BATTERY VOLTAGE SENSOR TEST
1) KEY OPERATION
2) TEST PROCEDUREDisplays A/D conversion port read value.
0155 or greater: Normal0154 or smaller: Low battery display0138 or smaller: No battery display and MSR is done when power on.To terminate the test, press any key.
Completion print 07
8. TIME DISPLAY TEST
1) KEY OPERATION
2) TEST PROCEDURE
To terminate the test and print the date and time, press any key.
9. DESTINATION DISPLAY
1) KEY OPERATION
2) TEST PROCEDUREDisplay the destination code as follows.
U and A version V version Japan
Display 0 1 2
Display X (X:0)
To terminate the test, press any key.
Completion print 09
PO5
PO6
PO7
PO8
8
Display
Hour Minute Second
Turn on and off(0.5s)
7 5 4 2 136
Year Month Date Hour Minute Second
0 8
X X X X X X X X X X X X
PO9
CHAPTER 6. SERVICE PRECAUTION
1. PRINTER
Since there are no service parts for this model printer, only the printerunit is supplied. Therefore, the printer component parts are not sup-plied and no service document is issued.
For troubleshooting of the printer, refer to the table below:
Printer life: 300 thousand lines (XE-A101: M-31)Ink roll life: 1 million characters
Phenomena Check point/possible cause Repair
• The printer motor is locked and thebuzzer sounds intermittently.
• Check if the printer cable is disconnected. • Check and repair the printer cable.
• The printer does not work properly • Check if the printer life is reached. • Replace the printer.
• Check if any foreign material is attached to theprinting type wheel or the gear section.
• Remove the foreign material. (After removingthe foreign material, set the mode switch to"REG" and press "CL" key.)
• Defective print (Lack on the upper/lower or left/right side)
• Check if the printing type is worn down. • Replace the printer.
• Check if any foreign material is attached to theprinting type wheel.
• Remove the foreign material. (After removingthe foreign material, set the mode switch to"REG" and press "CL" key.)
• Thin print • Check if the ink roll life is reached. • Replace the ink roll.
• Check if the ink roll is properly installed. • Install the ink roll properly.
• Check if the printing type wheel is worn down. • Replace the printer.
• Uneven pitch of print paper feed • Check if the roll paper size is proper. • Use roll paper as specified below;
Paper width: 57.5 0.5mmOutside diameter: ϕ80mm or lessInside diameter of paper tube: ϕ12mm or lessPaper thickness: 0.06~0.085mm
• Check if a load is applied to the roll paper duringpaper feeding. This may result from a foreignmaterials attached to the roll paper.
• Remove any foreign material.
R21
R24
XE
-A10
1X
O
*CA
UT
ION
*
87
65
43
21
ABCD
12
34
56
78
D C B A
1/2
R6
100K
VO
1 2 3
CN
350
45-0
3A
C8
MU
LTI
0.1u
F
Q1
2SD
2170
R7
1K
/PO
F
DR
(for
DR
AW
ER
)
F2
T40
0mA
/250
V
R3
68K
VC
C
VD
D
R4
5.6K
R5
56K
VO
VC
C
D9
1SS
133
D10
1SS
133
VB
AT
ZD
1M
TZ
7.5B
C6
47uF
/16V
(G3)
C26
47uF
/16V
C7
0.1u
FM
ULT
I
C4
100u
F25
V
VO
+6V
R2
1M
R1
220
C3
330u
F25
V
12
3
IC1
KIA
7806
P
C5
MY
LOR
0.1u
F
D5
1N40
02
D6
1N40
02
D7
1SS
133
D8
1SS
133
/RE
SE
T
1 2
CN
2
5267
-02B
LB
AT
TE
RY
CN
R70
100
1 2
CN
1
5273
-02A
VO
C2
3300
uF25
V
VD
D
C1
MY
LOR
0.03
3uF
D4
1N40
02x4
D2
D3
D1
R9
4.7K
F3
T1.
0AL/
250V
F1
T1.
25A
L/12
5VT
1.0A
L/25
0V
DR
RW
ND
VD
D
VC
C
C9
22uF
50V
D11
1N40
02
/ST
1/S
T2
Q2
2SD
2170
R10
2.7K
1 P
50/A
82
P51
/A9
3 P
52/A
104
P53
/A11
5 P
54/A
126
P55
/A13
7 P
56/A
148
P57
/A15
9 V
SS
010
VD
D0
11 P
3012
P31
13 P
3214
P33
15 P
34/S
I31
16 P
35/S
O31
17 P
36/-
SC
K31
18 P
20/S
I30
19 P
21/S
O30
20 P
22/-
SC
K30
21 P
23/R
XD
022
P24
/TX
D0
23 P
25/A
SC
K0
24 V
DD
125
AV
SS
26 P
17/A
N17
27 P
16/A
N16
28 P
15/A
N15
29 P
14/A
N14
30 P
13/A
N13
31 P
12/A
N12
32 P
11/A
N11
P10
/AN
10 3
3A
VR
EF
34
P47
/AD
7 64
P46
/AD
6 63
P45
/AD
5 62
P44
/AD
4 61
P43
/AD
3 60
P42
/AD
2 59
P41
/AD
1 58
P40
/AD
0 57
P67
/AS
TB
56
P66
/-W
AIT
55
P65
/-W
R 5
4P
64/-
RD
53
P75
/BU
Z 5
2P
74/P
CL
51P
73/T
I51/
TO
51 5
0P
72/T
I50/
TO
50 4
9P
71/T
I01
48P
70/T
I00/
TO
0 47
P03
/INT
P3/
AD
TR
G 4
6P
02/IN
TP
2 45
P01
/INT
P1
44P
00/IN
TP
0 43
VS
S1
42X
1 41
X2
40IC
39
XT
1 38
XT
2 37
-RE
SE
T 3
6A
VD
D 3
5
IC2
uPD
7800
23A
(Q
FP
)
SA
2S
B2
SC
2S
D2
SE
2S
F2
R8
1K
D12
1SS
133
1 2
CN
4
5267
-02
MO
TO
R C
N
(F3:
JUM
PE
R)
MT
RT
RG
KS
T1
KS
T2
KS
T3
KS
T4
KS
T5
KS
T6
KS
T7
KS
T8
KS
T1-
KS
T8
BZ
BU
ZZ
ER
Q3
C31
98C
10M
YLO
R0.
1uF
C11
MU
LTI
0.1u
F
R11 1K
VC
C
ST
RO
BE
[/S
T1-
/ST
4,S
T5]
R23
47K
R24
47K
R21
47K
R22
47K
VC
C
NO
T U
SE
+6V
R58
330
R59
6.8K
R60
330
R61
6.8K
Q8
KT
A12
71Q
9K
TA
1271
41 7
1 81
23
1 51 6
97
1 25
68
1 01 1
1 41 3
LED
1D
568G
WA
41 7
1 81
23
1 51 6
97
1 25
68
1 01 1
1 41 3
LED
2D
568G
WA
D30
JUM
PE
R W
IRE
(1N
4002
)
R51
12K
R50
4.7K
Q4
2SC
3198
R52 33
0
R53
6.8K
R54
330
R55
6.8K
Q5
KT
A12
71Q
6K
TA
1271
R56
330
R57
6.8K
Q7
KT
A12
71
41 7
1 81
23
1 51 6
97
1 25
68
1 01 1
1 41 3
LED
3D
568G
WA
1 41 3
LED
4D
568G
WA
38
41 7
1 81
23
1 51 6
97
1 25
68
1 01 1
51 0
91
24
67
LED
5S
568G
WA
(XE
-A10
1V o
nly)
IC4
KID
6508
3
KR
1
/PO
FTtR
VD
DV
CC
2
31
X2
4.19
MH
z
SG
2
SG
1
R27 1M
SD
P1
SD
P2
R25
470
/RE
SE
T
/RE
SE
T
P74
X1
32.7
68K
Hz
J6 7mm
SP
1S
HO
RT
PIN
R26
330K (0
)
C12
22pF
(18p
F)
C13
30pF
(22p
F)
SA
1S
B1
SC
1S
D1
SE
1S
F1
VB
AT
KR
6K
R5
KR
4K
R3
KR
2
KR
1-K
R6
VD
D
/ST
3/S
T4
R12
56K
R13
56K
R14
56K
ST
5
SI3
0S
O30
/SC
K30
VD
D
VD
DV
SS
VP
P
R15
R16
R17
R18
R19
R20
+6V
R28
1K
R29
1KR
30 1K
TR
GM
TR
47K
*6
PR
INT
ER
I/F
PW
BM
AIN
PW
B
1 N
C2
I13
I24
GN
D
NC
8O
1 7
O2
6V
CC
5
IC3
LB12
68(D
IP)
1 2 3 4 5 6 7 8
CN
5
5201
1-08
10
(for
PR
INT
ER
)
1 2 3 4 5 6 7 8
CO
N3A
HO
LE o
nly
1 2 3 4 5 6 7 8
CO
N3
HO
LE o
nly
a2 b2 c2 d2 e2 f2 g2 dp2
a1 b1 c1 d1 e1 f1 g1 dp1
SA
2S
B2
SC
2S
D2
SE
2S
F2
SG
2D
P2
SA
1S
B1
SC
1S
D1
SE
1S
F1
SG
1D
P1
9PIN
:GN
D10
PIN
:N.C
IC5
KID
6508
3
9PIN
:GN
D10
PIN
:N.C
VC
C
16 3
15 4
13 6
11 8
17 2
15 4
13 6
14 5
16 3
18 1
12 7
14 5
18 1
IC4A
17 2
IC4B
11 8
IC5H
12 7
IC5G
T R t
+6V
R31
10K
R32
10K
R33
10K
C14
C15
C16
0.1u
F0.
1uF
0.1u
F
R34
110
R35
110
R36
110
R37
110
R38
110
R39
110
R40
110
R41
110
R42
110
R43
110
R44
110
R45
110
R46
110
R47
110
R48
110
R49
110
1) M
AIN
CIR
CU
IT
CH
AP
TE
R 7
. CIR
CU
IT D
IAG
RA
M A
ND
PW
B L
AY
OU
T1.
CIR
CU
IT D
IAG
RA
M
87
65
43
21
ABCD
12
34
56
78
D C B A
2/2
2) K
EY
INT
ER
FA
CE
KR
1-K
R6
KR
2
KR
6
C17
100p
F
C18
100p
F
C19
100p
F
1 2 3 4 5 6 7 8 9 10
KC
N1
5204
5-10
45(M
AIN
PW
B)
1 2 3 4 5
SW
1
MO
DE
SW
SLI
DE
SW
PW
B
RE
G(1
)
VO
ID(2
)
X/F
LAS
H(3
)
Z/P
GM
(4)
KR
1
KS
T2
KS
T3
KS
T4
KS
T5
KR
1 KS
T2
KR
5
KR
4
KR
3 KS
T3
KS
T4
KS
T5
JP1
JUM
PE
R W
IRE
JP2
JUM
PE
R W
IRE
JP3
JUM
PE
R W
IRE
JP4
JUM
PE
R W
IRE
JP5
JUM
PE
R W
IRE
MA
IN P
WB
C20
100p
F
C21
100p
F
1 2 3 4 5
KC
N3
5229
-05A
PB
C22
330O
pF
C23
3300
pF
C24
3300
pF
C25
3300
pF
C29
330O
pF
PO
WE
RO
FF
RE
G(1
)V
OID
(2)
X/F
(3)
Z/P
GM
(4)
201134 12 21
1356 14 23
SLI
DE
SW
22 731 15
16
26 8 171891
2 10 19
XE
-A10
1
KS
T1
KS
T2
KS
T3
KS
T4
KS
T5
KS
T6
KS
T7
KS
T8
KS
T1
KS
T1-
KS
T8
D13
1SS
133
D14
1SS
133
D15
1SS
133
D16
1SS
133
D17
1SS
133
D18
1SS
133
D19
1SS
133
D20
1SS
133
67
1325
12
814
11 17 28 30 32 29312226241812
19 3 20 21 15 27165410239
KE
YB
OA
RD
1 2 3 4 5 6 7 8 9
KC
N2
5204
5-09
45(5
597-
09C
PB
)24
2527
2829
3032
2. P
WB
LA
YOU
TUT
1) A
sid
e
1) B
sid
e
COPYRIGHT 2001 BY SHARP CORPORATION
All rights reserved.Printed in Japan.
No part of this publication may be reproduced,stored in a retrieval system, or transmitted.
In any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,without prior written permission of the publisher.
SHARP CORPORATIONDigital Document Systems GroupQuality & Reliability Control CenterYamatokoriyama, Nara 639-1186, Japan
2001 August Printed in Japan