PUMPING STATIONS CHECK VALVES AIR VALVES KNIFE GATE VALVES PENSTOCKS

SEW

AGE

CATA

LOGU

E SEWAGECATALOGUE

2 3

WHO WE

ARE

13187 29 000 19 000 Over 50 1 300 FACTORIES

WORLDWIDE

COUNTRIES

SALES IN DIFFERENT

PRODUCTS IN CATALOGUE

CUSTOMERS

SALES PARTNERS EMPLOYEES

TALIS is a leading global provider of premium valves, hydrants and other solutions for water flow control. With a varied range of products, we offer comprehensive solutions for the entire water cycle, from hydrants to butterfly valves, from knife-gate valves to needle valves. Our experience, innovative technology, global expertise and individual consultation process, form the basis for developing sustainable solutions for the efficient handling of the vital resource “water”.

With over nine strong brands and 28 entities in Germany, France, Spain, Portugal, Italy, Great Britain, the Netherlands, Russia, Poland, Israel, China, the Middle East, Mexico, India, South Africa and Singapore, TALIS is the largest supplier of valve technology and first choice when it comes to water valves and services for the whole water cycle.

Foundation of ERHARD (D)

Water taps

Foundation of BAYARD (FR)

Beer taps and water

fountains

Foundation of SCHMIEDING

(D)

Modern and market

orientated solutions

Foundation of LUDWIG FRISCHHUT

(D)

« in-house » foundry

Foundation of STRATE (D)

Product and problem-solving

competenceSewage industry

Foundation of BELGICAST (ES)

Valve manufacturer for the naval

industry

Foundation of ATLANTIC PLASTIC (UK)

Plastic fittings

Acquisition by Triton

and creation of TALIS

Russia (2011)China (2012)Brazil (2013)

Middle East (2013)

Launch of « Smart-Inside »

solutions to make our products smarter

-South Africa

Mexico (2015)Joint-Venture

with Kc-Val (2016)India (2016)

Singapore (2016)

New logistic centre in Germany

Growth of TALIS Team in India

Support in engineering

and marketing services

1871 18801874 1945 1949 1957 1974Acquisition

by Tyco Waterworks

2001 2010 2011/13 2014Foundation of UNIJOINT (NL)

Adapters and extensions, pipe couplings, flange

adapters and dismantling joints

1992 2015/16 2017 2018

TALIS STRIVES TO SERVE YOU AS OUR CUSTOMERWITH SUPERIOR QUALIT Y AND SERVICE LEVELS.Continuous innovation of our products and applicationspaired with technical support allows you to maintain yourcritical water infrastructure with confidence. »

TALIS Management

first choice when it comes to water valves and services for the whole water cycle.

18 SALES & SERVICE OFFICES

TALIS SALES

TALIS OFFICES/FACTORIES & SALES

4 5

DOMESTI

C

WASTEW

ATER

INDUSTRY

WASTEW

ATER

AGRICUL

TURE

WASTEW

ATER

AWALIFTpumpingstation

Clean water

RIVERRELIEF VALVESp. 20

EVA START UPRELIEF VALVE

WASTEWATERTREATMENT PLANT

CONNECTIONSp. 15-16

CENTRICBUTTERFLY VALVES

p. 13

AIR VALVESp. 17-19

ISOLATING VALVES - p. 6-7

FITTINGS

AWALIFTp. 14

INFINITY RESILIENTSEAT GATE VALVE

METAL SEATGATE VALVE

CHECK VALVES - p. 8-12AWASTOP CHECK VALVE RSK CHECK VALVE REFLUX

CHECK VALVEERK TILTING DISC

CHECK VALVE

BALL CHECK VALVE

AVUSE COMPOSITEAIR VALVE

BEVSEWAGE AIR VALVE

EUROCOUP

PAS10

KNIFE GATE VALVESp. 21

GOLD

BEVTWO-STAGE SEWAGE

AIR VALVE

PENSTOCKSp. 22

WAGU® RANGE

Water pollution is a result of the impact of human activities on fresh water. Industry, domestic use, agriculture... there are many sectors that use water and pollute.Domestic wastewater includes water used for household and hygiene purposes: showering, dishwashing, toilet flushing, which in general contains chemicals (detergents and solvents), fats and organic materials.

Industrial wastewater differs from domestic water. In addition to organic materials, it also contains toxic products: solvents, heavy metals, organic micropollutants and hydrocarbons.

Stormwater does not always have polluting substances. However, if it runs through an urban environment and / or mixes with sewer overflows, it becomes similar to domestic sewage that may contain toxic substances.

Agricultural wastewater carries fertilisers, pesticides, herbicides and organic waste. To treat this wastewater, it is necessary to collect it and transport it to wastewater treatment plants.

This is where TALIS offers you its expertise, experience and appropriate solutions.

6 7

RESILIENT SEATED GATE VALVES

INFINITY FOR SEWAGEDN: 40 to 700Body length: Short and long series, S14 and S15, according to EN558.BS version: S3 according to EN558.Clockwise closing as standard. Anticlockwise closing as option.

Nominal Pressure (PN):Working: PN16Drilling: PN10 or PN16Medium Temperature: Epoxy coating: -10 to 50 ºCEnamel coating: -10 to 50 ºC

CHARACTERISTICS

Made of high quality materials according to the relevant standards.

Clear way and straight bore, so the flow is optimum with minimum head losses.

Replaceable packing under pressure.

Maintenance free.

Bayonet stuffing nut with three O-rings to guarantee the tightness throughout the stem (up to DN300).

Patented* three locking tab for bayonet system up to DN300 to avoid self dismantling, leakage and blow up risk.

Innovative dust guard made of three O-rings integrated into one single piece that protects the valve from floods, salt spray and dust, and ensures full isolation (up to DN300).

Wedge fully encapsulated in NBR for a better resistance to corrosion.

Integral male composite sliding skate as guiding system for easy operation under maximum differential pressure for a longer service life.

Body bonnet bolts are protected with hot melt glue.

Rounded surfaces of the body ensure a uniform coating and protection of the highest quality.

Excellent corrosion resistance thanks to the fully coated bonnet (not threads) and the epoxy powder coating.

Low torque - INFINITY and its new wedge and stem technology ensures smooth functionality with outstanding low torque values.

(*) : list of the countries on request.

METAL SEATED GATE VALVES

DN: 50 to 1800Body length: Acc EN558:Short pattern (Serie 14)Long pattern (serie 15) BS (serie 3)Clockwise closing as standard. Anticlockwise closing as option.

Nominal Pressure (PN):Working: PN16Drilling: PN10 or PN16Medium Temperature: Epoxy coating: -10 to 50 ºCEnamel coating: -10 to 50 ºC

CHARACTERISTICS

Made of high quality materials according to the relevant standards.

Full and straight bore, so the flow is optimum with minimum head losses.

Excellent corrosion resistance thanks to the fully coated bonnet and the epoxy powder coating 250µ. Body bonnet bolts are protected with wax.

Maintenance free.

The rounded surfaces of the body ensure a uniform coating and protection of the highest quality.

Approved by major organizations worldwide.

Prepared for actuator version available.

Standard design DIN3352 and BS5163.

OPTIONS Clockwise closing spindle as

standard, anti clockwise closing as an option.

Handwheel or steam cap operation.

Prepared for actuation: electric or pneumatic.

Face to Face Dimensions: 3S EN 558.

Gearboxes bevel or spur.

Position indicator.

Locking device.

By-pass.

Extension spindle and fee keys.

Alternative flange drillings.

Coating thickness.

8 9

CHECK VALVES

AWASTOP CHECK VALVE

CHARACTERISTICS

100% free passage for a low head loss thanks to a total clearance of the flap.

Quiet operation due to the inclined valve seat which shortens the closing distance.

Minimum clogging through optimum hydraulic design. The closing element with its vulcanized closing plate is the only moving part of the valve. No risk of clogging around an axis or a lever and weight.

Broad valve seat which prevents valve wear and failure even at elevated pressure.

Easy maintenance due to the screwless valve flap for simple replacement or washing. The removable bonnet enables flap access without removing the check valve from the pipe.

Leak-proof even with low counter pressure thanks to the sealing lip profile and the shore hardness of the flap.

For gas application: nickel-coated version with silicone flap.

Preferred flow range up to 1,5 + 0,5 m/s: if higher flow velocity please use RSK check valve.

Reliable for a long-term proper operation and protection of pumps.

Other rubber types are available on request e.g. Perbinan, Viton, Silicone, etc for operating temperature up to +250 °C.

DN: 50 up to 300Working pressure: 10 bar Maximum speed: 1.5 + 0.5 m/s Medium Temperature: -35 °C to +60 °C for standard product. For dry gases up to +120 °CHorizontal or upward vertical installation

CHECK VALVES

RSK CHECK VALVEDN: 80 up to 900Working pressure for DN80 to DN350: 10 barWorking pressure for DN400 to DN900: 6 bar / 10 barMaximum speed: 2.5 + 0.5m/s RSK-UD RSK or RSK-U 2.0 to 6.0m/s RSK-FTU or FTUD FTMedium Temperature: -35 °C to +60 °C for standard productHorizontal or upward vertical installation

CHARACTERISTICS

Particularly suitable for “heavy duty” applications – Even where there is a high risk of water hammer or pressure surge.

Specific variants – For a custom-made solution according to DN and network constraints.

Low flow resistance design.

Quiet operation – Thanks to the flap fully vulcanized in rubber.

Minimum clogging tendency through free flow cross-section.

Fail-safe closing of the disc even under high pressures.

Easy access to the closing element thanks to the removable inspection cover.

Reliable Designed to function properly with sewage fluids, media with coarse solids and sludge, but also where powerful pumps are necessary.

RSK housing-

RSK coverValve armValveinsert

Spring loading device

Pumping direction

Pressure surgedamping valve

Valve spring

Bypass

10 11

CHECK VALVES

REFLUX CHECK VALVE

CHARACTERISTICS

Optimal corrosion protection is guaranteed by inside and outside epoxy coating 250µm. In option with inside enamel coating.

Disc is rubberized with NBR to ensure a perfect sealing.

Rapid and silent closing on flow reversal.

Option: lifting device for disc.

Back pressure for absolute tightness: 0.4-0.6 bar needed.

Sizes and pressure rates DN40 mm up to DN300 mm PN16Materials Body and cover: EN-JS 1050 Face to face according to EN 558

CHECK VALVES

ERK TILTING DISC CHECK VALVEDN: 150 up to 1400Working Pressure (PN): DN200 up to DN1400: PN10Or DN150 up to DN1200: PN16Or DN150 up to DN1200: PN25Or DN150 up to DN700: PN40Medium Temperature: 20 °C up to +60 °CMaximum speed: 5 m/s for DN150 to DN300 (working pressure 16 bar) 3 m/s for DN350 and DN400 (working pressure 10 bar)

CHARACTERISTICS

Low head loss is ensured by the double-offset free-swinging disc, key component of the ERK. The disc is freely oscillating and has a flow-facilitating design with its double eccentricity supports.

The spontaneous position of the disc will be where the effort is the lowest, thus ensuring low head loss.

Double eccentric design is an advantage for:• Low operating torque. • No premature wear of the disc and

gasket.

Maximum crossing section reached by a two-part shaft.

Maintenance-free valve Thanks to the construction of the shafts, self-lubricating friction bearings and maintenance-free seals from the shaft.

Perfect sealing – Provided by a rolled up, solid body seat ring made of stainless steel, and a disc seat ring which is additionally provided with a resilient precision seal.

Low operating torque  – Thanks to the double eccentric design, ensuring also a low wear and tear of the disc seal.

Protection against corrosion – Brought by the choice of stainless steel for the shafts, the body seat and the disc seat.

Shafts protruding on both sides to facilitate individual mounting of the weight-loaded lever.

Free-swinging disc means that the disc will place itself in an optimum position driven by the flow passing through the valve during operation.

1 Robust body and streamlined disc

2Shafts protruding on both sides facilitating individual mounting of the weight-loaded lever

3Maintenance-free, selflubricating shaft bearings (long shaft supports)

4 Maintenance-free shaft-sealing.

5Robust disc-to-shaft key connection with special key securing device

6 Solid, rolled-in body seat ring of stainless steel

7Disc facing ring of stainless steel plus resilient precision seal

21

7 6

34

5

12 13

CHECK VALVES

BALL CHECK VALVEThreaded type: 1” to 3”Flanged type: DN40 up to 400Working pressures: 16 bar up to DN20010 bar for DN250 to DN400Medium Temperature: -10 °C up to +80 °C

CHARACTERISTICS

Robust construction – Ball fully encapsulated in moulded NBR, corrosion protection thanks to epoxy coating, bolting in stainless steel A2.

Self-cleaning – Thanks to the rolling ball, movement will ensure auto-cleaning of the ball and internal body.

Ball types option – Lower weight balls depending on particular requirements.

Different possible installations – Horizontal flow (fig.1), vertical flow upwards (fig. 2) or floating ball check valves (fig. 3 and 4).

Maintenance – Easy internal access due to removable bonnet or seat.

Head loss – Low head loss due to full bore design.

Figure 1

Figure 2

Figure 3

Figure 4

STANDARD VERSION

Use on pumping stations. Vertical mounting with seat downward (Fig. 1) or horizontal mounting with upward housing of the ball (Fig. 2). The arrow indicates the flow direction, pumps in operation (same direction as that indicated on the ball check valve). From DN 400, indicate when consulting or ordering, the service conditions (pressure, flow…) as well as the type of mounting (horizontal / vertical).

FLOATING BALL VERSIONS

Use as single orifice air valve air inlet / outlet, no relief of air under pressure). Vertical mounting with seat upward (Fig. 3). The arrow indicates the air evacuation direction (oppo site direction to that indicated on the ball check valve).

Use for protection against water rise Horizontal mounting with downward housing of the ball (Fig. 4). The arrow indicates the direction of the water rise (oppo-site direction to that indicated on the ball check valve).

CENTRIC BUTTERFLY VALVES

GOLD

CHARACTERISTICS

Corrosion protection ensured by valve body fully covered by rubber liner and appropriate disc coating or material.

Flange gaskets incorporated in liner. No additional flange gaskets required.

Flexible installation – Valve can be installed between two piping flanges or at the end of pipeline with or without counter flange (see installation instructions), both installation directions are possible.

Low operating torques.

Long service life.

Easy maintenance with low costs.

Automation – Standard ISO 5211 connection flange allows the use of all different kinds of actuators.

Replaceable rubber liner.

Wide variety of applications including drinking water and industrial applications, due to the wide variety of high-grade materials for the liner and disc.

Compact and cost-efficient solution that allows economic layout of valve environment.

Proven design – Reliable product made in Europe successfully installed worldwide.

DN: 32 to 1800 (according to body design)

Nominal Pressure (PN): PN10 to PN16

Medium Temperature: Standard up to 60 °C (other possibility according to liner material)

WAFER TYPEDN32 - DN700

LUG TYPEDN32 - DN300

DOUBLE FLANGE TYPEDN250 - DN1800

14 15

PUMPING STATIONS

STRATE RANGE

The STRATE system is used as one of the characteristic features of all AWALIFT sewage pumping stations and stands for maximum operational safety, economic and user friendliness thanks to its combination of patented solids collecting chamber and centrifugal pump.The solids collecting chamber separates the sewage into “pre-cleaned” sewage and solids.Since the centrifugal pump only pumps “pre-cleaned sewage” it has optimum protection from soiling, blockage and wear.The result is extremely economic operation with maintenance costs reduced to a minimum.On request we also offer special solutions according to your needs.

Watch the Video "The STRATE System" for more informations.

MECHANICAL COUPLINGS AND FLANGE ADAPTORS

EUROCOUP

CHARACTERISTICS

Manufacturing and design – In accordance with AWWA-C219 guaranteeing an absolutely leakproof product.

High quality materials – Selected for strength and adaptability.

Proven design in many prestigious and challenging projects worldwide.

Body: EN-GJS-500-7 or S235EN10025. End rings: EN-GJS-500-7 or S275EN10025. Gasket: EPDM [EN681] or NBR. Bolts: Hot Dip Galvanized or Stainless Steel AISI316-A4.Flange drilling: PN10, 16, 25, 40 (ANSI Drilling on Request).Standard coating: Resicoat RT9000 R4 Epoxy, 305microns (Higher SteelGrades, Special Coatings, Various Flange Drillings/Dimensions, Bolt Materials, Gaskets available on request).

DISMANTLING JOINTS

PAS10

CHARACTERISTICS

Manufacturing and design – In accordance with AWWA-C219 guaranteeing an absolutely leakproof product.

High quality materials – Selected for strength and adaptability.

Proven design – In many prestigious and challenging projects worldwide.

Essential aid – For the installation and dismantling of pipe sections, valves and pumps.

Flange norm/drilling: ISO2531/EN1092 Raised Face – Reduced Bore (RF-RB).Body: EN-GJS-500-7, S235EN10025 and/or S275EN10025.Bolts, nuts & washers: Hot Dip Galvanized or Stainless Steel AISI316-A4.Tie- bars: Mild Steel Zinc Electroplated or Hot Dip Galvanized or Stainless Steel AISI316-A4.Gasket: EPDM [EN681] or NBR.

CHARACTERISTICS

Low operational cost.

Energy saving – due to hydraulically optimized pumps and efficient motors.

Easy to service at low maintenance costs.

High reliability of the pumps.

Durable technology up to 30 years ot more.

High environmental protection factor.

16 17

PIPE FITTINGS

CHARACTERISTICS

Optimal corrosion protection is guaranteed by high quality epoxy coating in accordance with GSK RAL-GZ-662 directive, conforming to DIN EN 14901.

High quality Fusion Bonded Epoxy Coating – Ensures a smooth surface and prevents lime deposits.

Colours – Blue RAL5015 (Standard),RedBrown (wastewater) & Yellow (gas)..

Designed – In accordance with the European Standard EN 545 Series A for ductile iron pipes and fittings.

Standard Flanges are measured, produced and drilled to DIN EN1092-2 [PN 10 or PN 16]. PN 25, PN 40 on request.

Special Fittings – Available on request (i.e. non-standard lengths).

CE-Label – Fittings used for gas supply to DIN EN 969 (since 01-01-2011) and for wastewater to DINEN 598 (since 01-04-2011) that are traded on the EU market must have the CE label. Please ensure to indicate this on every order when applicable.

Alternative Coatings – Inside Cement Lining or Inside Enamel.

Body: Ductile ironCoating: Epoxy 250μ min, GSK approved RAL-GZ-662 Nominal Pressure (PN): PN10/16 (PN25, PN40 on request).

AIR VALVES

AVUSE COMPOSITE AIR VALVESFlanged type: DN50 or multi-drilling DN 60/65/80Working pressure: 3 barMedium Temperature: up to +70 °CWeight: 6kg

AVUSE-1 AVUSE-3

CHARACTERISTICS

AVUSE-1 for degassing under pressure, AVUSE-3 for degassing, high flow rate air inlet and outlet.

Simple but studied design – to reach the best performances with optimized components.

Ventilation area protected – From splashes and clogging thanks to a specific deflector design, ensuring a long term operation.

Polymeric high-quality material.

Easy maintenance – Thanks to quick removal of the clamps and drainage cock.

Optional funnelled outlet – For pipe connection.

Lightweight – For easy handling and easy service cleaning.

Chemical and mechanical strong resistance.

INSTALLATION

18 19

AIR VALVES

BEV GFTwo-stage ventilation valve for ventilation volumes from 450 to 2000 m³/h in coarse up to 40 m³/h in fine ventilation.Flanged type: DN80/100/150 PN10/16Working pressure: Standard version 2/4/6 bar Special version up to 16 barMaterials: DN80/100: body EN-GSJ-400-15, coating EKB DN150: body S235 JR or L355, coating EKB

CHARACTERISTICS

Ensure the optimum venting and air release of sewage pressure pipe.

The valves are especially designed for the demands of sewage, according to the actual working pressure at the installation location and the flow rate in the pressure pipe.

They ensure reliable operation of pipeline and pumps.

They provide full pump performance and optimal protection against pressure surge and water hammer, to a specific deflector design, ensuring a long term operation. It also provides a vacuum protection.

AIR VALVES

BEV SEWAGE AIR VALVESizes and pressure rates:DN80-200 PN16DN200 PN10Materials:Body and bonnet: Cast iron EN-JS1030Body components: Cast iron EN-JL1040Floating body, seat rings, nozzles and connecting bolts: Stainless steelCoating: Inside and outside epoxy against corrosion

CHARACTERISTICS

The large nozzle of the body cover closes automatically in case of excessive air outflow. This feature protects the nozzle against deposits.

Operating thanks to the aerocinetic principle, with high safety of the floating body.

The precised adjustment of the air flow level triggers the surge absorption and protects from contamination.

Construction simple and robust construction for hard working conditions.

Option a diameter extraction DN80 and a version with ventilation lock is available.

Air valves should be located at the following points in a pipeline:• At each absolute high point [1]• At each high point where pipe section has an ascending run compared to the

hydraulic gradient, or when the slope decreases [2]• At each point where a pipeline slope starts [3]• At each pipeline point endangered by negative pressure [4]• On long, rising or sloping pipeline sections at distances of approx. 800 m [5]

TYP VENTILATION VOLUME 1. STAGE

VENTILATION VOLUME 2. STAGE

FLANGE DN/PN

450/20 GF-80 450 20 80/101000/20 GF-100 1000 20 100/102000/20 GF-150 2000 40 150/10

20 21

RELIEF VALVES

EVA START-UP RELIEF VALVEMax volume in m3/min: 10 to 150Max working pressure: 1000 mbarMax working temperature: 130°CSizes: 2”1/2 - 4” with threaded ends DN150 - DN200 with flanged ends

ADVANTAGE

CHARACTERISTICS

The STRATE start-up relief valve (EVA) is a medium-controlled valve for unloaded start-up of rotary lobe blowers and single-stage screw compressors with aggregate outputs up to 160 m³ / min. Rotary blowers and single-stage screw compressors with drive motors from 3 kW start in YD-circuit. Since there must be no back pressure during the start-up phase, it is necessary to blow off the volume flow for this time. This has hit her to been done by consuming, externally controlled valves.

With solenoid valve.

With adjustable pressure valve.

With adjustable pressure valve and solenoid valve.

THE STRATErelief valve is a medium-controlled, automatic, low-maintenance and therefore economic start-up relief.

KNIFE GATE VALVES

ERU® K1Sizes and pressure ratesDN50 mm up to DN350 mm - PN10DN400 mm up to DN600 mm - PN4Materials Frame: EN-JL 1040Sliding plate, stem: Stainless steel Sealing: EPDM, wastewater resistant Stem nut: BrassPressure DN400 mm up to DN600mm - PN6 on requestDiameter > DN600 on request

CHARACTERISTICS

Stem not in contact with medium. For flooded valves, a rising extension stem is optional.

Sealing on both sides for bi-directional tightness .

Low operating torques resulting in smaller drives.

Transverse seal adjustable.

U-shaped main sealing changeable without removing the valve.

Epoxy coating according to GSK requirements.

ECO®

Nominal Diameter (DN) and Nominal Pressure (PN):DN50 mm up to DN100 mm PN10DN125 mm up to DN 300 mm PN6DN350 PN4DN400 up to 600PN 2.5

Between flange DN50 – 150 (DIN EN 1092 – 1 and 2) PN10Between flange DN200 – 600 (DIN EN 1092 – 1 and 2) PN10

MaterialsBody parts, flange ring up to DN400: stainless steel A4Body parts DN450 and larger: stainless steel A2, flange ring: stainless steel A4Valve plate and parts, connecting parts, stem: stainless steel A2Seal: Elastomer / PTFE

CHARACTERISTICS

Sealing on both sides for bi-directional tightness.

Low operating torques due to side plate guides in sliding shell.

Replacement of the upper gate seal without dismantling the gate valve.

Fully formed flange partially with blind threaded holes.

Dimensionally stable pressed body with full straight-through bore.

Enclosed profile seal.

22 23

PENSTOCKS

WAGU® RANGEThe wide variety of versions and materials of WAGU® penstocks are ideally suited to isolation and regulation purposes in sewage engineering.

CHARACTERISTICS

Modular structure for all operating options and for individual designs and sizes.

Material selection comprising stainless and special materials.

Long-term use sealing principle.

3 or 4-facing seals with bi-directional tightness.

Non-abrasive guides.

Low actuating forces.

Maintenance-friendly.

Easy installation.

WAGU® penstocks without housing are used as isolating and regulation devices and they are designed for the use in the fields of sewage and waste engineering. They are field-proven for isolating and regulating and can be used in open channels, inlets and outlets of canals, sewers, pits, basins, and pipelines. The wide scope of applications includes flow control, maintaining the sewage level, flow limitation, distribution of channel flow and ensuring of recirculation. Our wide variety of design versions and different materials provides you with a range of WAGU® penstocks that can handle nearly all demands in the field of sewage engineering. WAGU® penstocks are available from 150mm to 3000mm and in different materials.

24 25

REFE

RENC

ESTROPICAL ISLANDS SEWAGE PUMPING STATIONGERMANY

KAPPEL GRAFENHAUSEN WATER SEWAGE PUMPING STATION GERMANYRSK check valves

24 25

SMOLTEN WATER TREATMENT PLANT NORWAYBall check valvesResilient seat gate valves

TROPICAL ISLANDS SEWAGE PUMPING STATION GERMANYResilient seat gate valvesRSK check valves

26 27

REFE

RENC

ES

EDAR SOPUERTA WASTE WATER PLANTSPAINResilient seat gate valvesBall check valves

AL AIN PROJECTABU DHABIDismantling jointButterfly valve

26 27

AWALIFT PUMPING STATION TROPICAL ISLANDS

GERMANYAWALIFT 4-2 pumping station

ARCACHON WASTE WATER PLANT FRANCEFlanges adaptorsRSK check valves

TALIS Management HoldingPostfach 1280

D-89502 HeidenheimMeeboldstrasse 22

D-89522 Heidenheim

Telefon:: +49 7321 320-0Telefax: +49 7321 320-491

info@talis-group.comwww.talis-group.com

Note: Information and specifications may be changed without notification at any time.Copyright: No copying without express written permission of TALIS

TALIS is a Registered Trademark.