Setting up CODE CR1400 Scanner for RapID Tags as a Virtual ... · Doc20 Rev. 02 Copyright © 2016...
4
Doc20 Rev. 02 Copyright © 2016 RapID Lab, Inc. All rights reserved. Setting up CODE CR1400 Scanner for RapID Tags as a Virtual COM Port The instructions below will help you download and install the CODE Virtual COM Port Drivers and program your CODE Scanner. More information may be found on the RapID Lab website: http://rapidlab.com/scanner-and-software-support/ 1. Install the correct USB Virtual COM Port driver for your system: a. Windows XP (32 Bit) - http://codecorp.com/eulausbvirtualcomdriver.php b. Windows XP (64 Bit) – Not supported at this time. c. Windows 7 (32 Bit) - http://www.codecorp.com/downloads.php (Scroll to Bottom of Page) d. Windows 7 (64 Bit) - http://www.codecorp.com/downloads.php (Scroll to Bottom of Page) 2. Reset the Scanner: a. Unplug the CODE CR1400 from the PC. b. While holding the trigger pressed, plug the reader into the USB port on the PC and hold for 5-10 seconds. You will hear 5 rapid beeps and then you can let go of the trigger. The unit is now in Boot Mode. c. Next, hold the trigger down again for approximately 5-10 seconds until it reboots. The reader will vibrate first and then beep several times and is now reset. 3. Reprogram the scanner: a. Scan the codes below to reprogram your scanner. Required Codes: Optional Codes: This turns the scanner into a continuous scan mode that works well for hands free operation. Note that the CR1400 will enter into Continuous Scan mode by default when placed in the Scanner Stand. This sets a duplicate rejection period of 1 or 3 seconds so that tags are not ‘double scanned’.
Transcript of Setting up CODE CR1400 Scanner for RapID Tags as a Virtual ... · Doc20 Rev. 02 Copyright © 2016...
Doc20Rev.02
Copyright©2016RapIDLab,Inc.Allrightsreserved.
SettingupCODECR1400ScannerforRapIDTagsasaVirtualCOMPort
TheinstructionsbelowwillhelpyoudownloadandinstalltheCODEVirtualCOMPortDriversandprogramyourCODEScanner.MoreinformationmaybefoundontheRapIDLabwebsite:http://rapidlab.com/scanner-and-software-support/1. InstallthecorrectUSBVirtualCOMPortdriverforyoursystem:
a. WindowsXP(32Bit)-http://codecorp.com/eulausbvirtualcomdriver.phpb. WindowsXP(64Bit)–Notsupportedatthistime.c. Windows7(32Bit)-http://www.codecorp.com/downloads.php(ScrolltoBottomofPage)d. Windows7(64Bit)-http://www.codecorp.com/downloads.php(ScrolltoBottomofPage)
2. ResettheScanner:a. UnplugtheCODECR1400fromthePC.b. Whileholdingthetriggerpressed,plugthereaderintotheUSBportonthePCandholdfor
5-10seconds.Youwillhear5rapidbeepsandthenyoucanletgoofthetrigger.TheunitisnowinBootMode.
c. Next,holdthetriggerdownagainforapproximately5-10secondsuntilitreboots.Thereaderwillvibratefirstandthenbeepseveraltimesandisnowreset.
3. Reprogramthescanner:a. Scanthecodesbelowtoreprogramyourscanner.
RequiredCodes:
OptionalCodes:
Thisturnsthescannerintoacontinuousscanmodethatworkswellforhandsfreeoperation.NotethattheCR1400willenterintoContinuousScanmodebydefaultwhenplacedintheScannerStand.
Thissetsaduplicaterejectionperiodof1or3secondssothattagsarenot‘doublescanned’.
Doc20Rev.02
Copyright©2016RapIDLab,Inc.Allrightsreserved.
SettingupStudylog®V3withtheCODE1400Scanner
TheinstructionsbelowwillhelpyousetupStudylogStudyDirectorV2forusewiththeRapIDTag.MoreinformationmaybefoundontheRapIDLabwebsite:www.rapidlab.com/support.
1. MakesureyouhaveinstalledtheUSBVirtualCOMDriverforyourspecificsysteminstalledcorrectly.
2. OpenDeviceManager:a. WindowsXP-ClickonStartandthenControlPanel.ClickonthePerformanceand
Maintenancelink.InthePerformanceandMaintenancewindow,clickontheSystemiconnearthebottomofthewindow.IntheSystemPropertieswindow,clickontheHardwaretab.WiththeHardwaretabselected,clickontheDeviceManagerbutton.
b. Windows7-Clickonthestartmenuandtype‘DeviceManager’intothesearchfield.HitEntertoopendevicemanager.
3. ClickonPorts(COM&LPT)toviewthecurrentPortsinuseonyourcomputer.a. TakenoteoftheUSBtoVirtualCOMPortthatisshown.SeeFigure1belowforan
example.
Figure1:DeviceManager
4. Doubleclickonthe‘USBtoVirtualCOMPort’Deviceandthenselectthe‘PortSettings’tabasshownbelowinFigure2.
NotethisSetting
Doc20Rev.02
Copyright©2016RapIDLab,Inc.Allrightsreserved.
Figure2:PortSettings
5. Leavethiswindowopen6. Pluginyourscanner7. IfStudyDirectorisalreadyopen,restarttheprogram.Otherwise,startStudyDirector.8. OnceinStudyDirector,selectTools->Optionsfromthemenubar.9. OncetheOptionswindowopens,configureyourscannerbysettingupanewdeviceasshown
inFigure3.PleasenotethatyourCOMPortshouldmatchthesettingfromyourDeviceManagerconfigurationshowninFigure1andmaybedifferentthanshowninthisguide.AllotherfieldsshouldbeEXATLYasshownbelow.
Doc20Rev.02
Copyright©2016RapIDLab,Inc.Allrightsreserved.
Figure3:DeviceManager
10. UsethemaskY*[\,]11. Select‘Testdevice’andscanaRapIDTagtoverifythatthescannerisworkingproperly.12. ClickOKtoclosetheOptionswindow.
Y*[\,]
Y*[\,]
