1 / 14

Ver. 2.0

1 March 2013

Selection Tool

Installation Manual

Kumanovska 14, 11000 Beograd, SrbijaTel.: 011 383 68 86, 308 57 40

Faks 011 344 41 13E-mail: gobrid@eunet.rs

www.airtrend.rswww.toshiba-klima.rs • www.toshiba-estia.rs

Kumanovska 14, 11000 Beograd, Srbija

Tel.: 011 308 57 40Faks 011 344 41 13

E-mail: o�ce@kovent.rswww.kovent.rs

2 / 14

– CONTENTS –

1. OVERVIEW ............................................................................................................................... 3

2. SYSTEM REQUIREMENTS ........................................................................................................ 3

3. INSTALLING / UNINSTALLING OF THE SELECTION TOOL ...................................................... 4

3.1 INSTALLATION ............................................................................................................................... 4

3.1.1 WELCOME .................................................................................................................................... 5

3.1.2 LICENSE AGREEMENT ...................................................................................................................... 6

3.1.3 CUSTOMER INFORMATION ................................................................................................................ 7

3.1.4 DESTINATION FOLDER ..................................................................................................................... 8

3.1.5 CHANGE CURRENT DESTINATION FOLDER ............................................................................................ 9

3.1.6 READY TO INSTALL THE PROGRAM ....................................................................................................10

3.1.7 INSTALLING SOFTWARE .................................................................................................................. 11

3.1.8 COMPLETED .................................................................................................................................12

3.2 UNINSTALLATION ..........................................................................................................................13

3 / 14

1. Overview

“Selection Tool” allows you to select a device such as an outdoor unit or indoor unit of a

Super Modular Multi system, Super Heat Recovery Multi system, Mini-SMMS system, and BMS

system. Using this tool, you can select a pipe according to the piping rules, automatically select

the indoor unit performance according to the requirements, and automatically create

piping/wiring diagrams and BMS system wiring diagrams.

The selection results can be exported as an Excel file for easy secondary use.

2. System requirements

The system requirements for this software are as follows,

Item Specifications

OS Windows XP SP2 or later, Vista

Office System —

Autodesk AutoCAD AutoCAD R14 or later

The following runtime library is installed when Selection Tool 2010 is installed:

Microsoft® .NET Framework 2.0 with SP2

・ “Windows XP”, “Windows Vista” and “Windows 7” are either registered trademarks or

trademarks of Microsoft Corporation in the United States and/or other countries.

・ Adobe, the Adobe logo, Reader, and Acrobat are either registered trademarks or trademarks of

Adobe Systems Incorporated in the United States and/or other countries.

・ InstallShield is either a registered trademark or trademark of Flexera Software Inc. in the United

States and/or other countries.

・ All other company and product names are either registered trademarks or trademarks of the

respective owners. In this manual such names are not indicated by ™, ® or © marks.

4 / 14

3. Installing / Uninstalling of the Selection Tool

This section describes installation and uninstallation procedures of the Selection Tool.

3.1 Installation

Insert the installer CD into the drive. The setup program execute ‘SETUP.EXE’ in the CD. When SETUP

is started, preparation for the installation starts. Wait for a while until the preparation is completed.

5 / 14

3.1.1 Welcome

When installation preparation process has completed, the Welcome window opens.

Click ‘Next >’.

6 / 14

3.1.2 License Agreement

The License Agreement window is displayed. Read the content. When you agree with the terms, select

“I accept the terms in the license agreement”. And Click ‘Next >’.

7 / 14

3.1.3 Customer Information

The Customer Information window is displayed. Enter ‘User Name’ and ‘Organization’. And Click ‘Next >’.

8 / 14

3.1.4 Destination Folder

The Installation Folder window is displayed. If the installation folder is correct, click ‘Next >’.

If you want to change the installation folder, click ‘Change’.

9 / 14

3.1.5 Change Current Destination Folder

The following Change Current installation folder window is displayed. Choose or enter installation folder.

And Click ‘OK’.

10 / 14

3.1.6 Ready to Install the Program

Ready to Install the Program window is displayed. Click ‘Install’.

11 / 14

3.1.7 Installing Software

The following window appears showing that the program is being installed. Wait for a wile.

12 / 14

3.1.8 Completed

When the installation is finished, the following window opens. Click ‘Finish’ to exit the installer.

13 / 14

3.2 Uninstallation

If the Setting File Creation Software is running, exit the application.

Select ‘Selection Tool’ on the Add or Remove Programs window in the Control Panel within Windows.

And click ‘Remove’.

The following confirmation dialog box appears. Click ‘Yes’.

14 / 14

The following window appears. Wait for a while.

When the uninstallation is finished, this window will close automatically.

Kumanovska 14, 11000 Beograd, SrbijaTel.: 011 383 68 86, 308 57 40

Faks 011 344 41 13E-mail: gobrid@eunet.rs

www.airtrend.rswww.toshiba-klima.rs • www.toshiba-estia.rs

Kumanovska 14, 11000 Beograd, Srbija

Tel.: 011 308 57 40Faks 011 344 41 13

E-mail: o�ce@kovent.rswww.kovent.rs