Service Mode Orion t2129mtx 163

6

5 For software (V1.1)alignment instruction This software OSD menu is Chinese/English OSD menu, there are hotel mode, game, calendar, 255 channel preset, intellectualized searching programs, auto menu demonstration function etc. and is suitable for sale in China and Australia market.

5.1 FIX 1 setting a) Enter method

Press | (picture mode) button, before picture mode status character display disappear, in turn press the password 9 , 8 , 7 , 1 , or use factory remote controller RC-K20 (or RC-K11 is also OK), directly press and hold “ADJ” button for long time to enter.

b) Exit method Press MENU button , enter into FIX 5(can check version number ), press MENU button again to exit. Or continually press ADJ button on the factory remote controller for three times to exit.

c) Adjustment method Use Channel up/down button to select and Volume up/down to adjust.

d) Only the following personnel have rights to change : Alignment personnel, service personnel, technicians and designer.

Chart 1 FIX 1 setting Item Name Range Software default value

00 RF Delay 00-7F 35

01 VIF VCO 00-3F 27

02 Video Gain 00-07 07

03 Audio ATT 00-7F 58

04 Y DL Time 00-03 03

05 SECAM R 00-0F 07

06 SECAM B 00-0F 07

07 H VCO 00-07 04

08 H Phase 00-1F 15

09 V Shift 00-07 00

0A V Size 00-3F 2E

0B SubContrast 00-1B 1B

0C SubBright 00-1B 10

0D SubTint 00-1B 10

Note 1: 01 item VIF VCO is CPU auto adjustment item, use Volume up/down button to activate.

Note 2: 08, 09, 10 items’value will be different in 60Hz/50Hz.


Press | (Picture mode) button, before picture mode status character display disappear, in turn press the password 9, 8, 7 , 2 , or directly press and hold “ADJ” button on the factory remote controller for a long time, enter into FIX 1, then press ADJ button again to enter into FIX 2.

b) Exiting method Press “MENU” button or press “ADJ” button on the factory remote controller for two times to exit.

c) Adjustment method Use Channel up/down button to select, Volume up/down button to adjust.

d) Only the following have rights to change:

7

Alignment personnel, service personnel, technicians and designer.

Chart 2 FIX 2 setting

Item Name Range Default value Driving address

(M6120x)

Store address

(24c08)

00 Service SW 00-01 00 Slave BAh Slave A0h

01 Drive R 00-7F 3F 0B 2B

02 Drive B 00-7F 3F 0C 2C

03 Cut Off R 00-FF 7F 0D 2D

04 Cut Off G 00-FF 7F 0E 2E

05 Cut Off B 00-FF 7F 0F 2F

e) BUS OFF” mode is used to auto adjust computer white balance. Directly press and hold “STOP” button on the factory remote for a long time to enter, BUS OFF” is displayed. The bus off is auto adjusted by computer white balance. After adjustment press “STOP” button on the factory remote again to exit, display

BUS On” relevant information.


Press “ | (picture mode) button, before picture mode status character display disappears, in turn press the password 9 , 3 , 7 , 3 .

b) Exiting method Press MENU button, or press “ADJ” button on the factory remote for two times to exit.


d) Only designer has the right to change: f) All the items are correspond to M61205/8 specifications. Among them the last one is reading status. And

10H’s last three digit is picture IF selection. 000 38MHz /001 38.9MHz/ 010 39.5MHz, etc.


Press “ | (Picture mode) button, before picture mode status character display disappears or in “Heat Run” status, in turn press the password 9 , 4 , 7, 4 . Or directly press and hold “STILL” button on the factory remote for a long time.

c) Exiting method Press “ MENU” button or press “ADJ” button on the factory remote for two times to exit.

d) Adjustment method Use Channel up/down button to select, volume up/down button to adjust.

e) Only the service personnel and technicians and designer have the right to change.


Item Name Select Software

default value Remarks

00 Heat Run On/Off <Off>

When On is selected, “Heat Run” will be displayed at all

time. At this time, remote operation will be ineffective

( only pressing and holding digit buttons can effect, and

exit “Heat Run” temporarily), the function of

8

auto-power-off when no signal is ineffective, ON/OFF

timer is cancelled, blue background function is cancelled,

turn on with the power switch, the power is supplied

immediately. To exit “Heat Run”, should press the

password “9” , “4” , “7” , “4”, enter into FIX 4, select Off to turn off.

01 Power memory On/Off <On>

When On is selected, the set will be in standby or

working when pressing the power switch. When Off is

selected, press the power switch , the set is in standby.

02 Net input Yes/No <No>When Yes is selected, it will go to net mode, AV

will display NET and be in Y/C input mode.

03 Blue Back Map On/Off <No> When On is selected, when no input signal, map

will be displayed on the blue background.

04 Channel Number 255/85 <85> Select 255 channels or 85 channels. The corresponding EEPROM is 24C08 or 24C04.

05 One Chip Type M61208/M61205

<M61205>Select the main IC (M61208 or M61205) , and M61208 has SECAM system.

06 PassWord Clear Really?/Cleared! <Cleared> Clear user’s safety mode password.

07 PowerOn Logo Yes/No <Yes> When Yes is selected, XOCECO will be displayed when turning on the set.

DK DK I I BG BG

08 SoundSys Opt

MN MN

<DK DK>

Select two sound system, and the first one is a prior system (correspondingly CPU Pin50 is high level). If only one sound system, both should be set in same.

5.5 FIX 5 setting The following is software version information: XOCECO Logo

SDA5523CHN1 Model Ver. 1.1 Version 02/07/2002 Date 5.6 “Standard”, “Vivid”, “Soft” these three preset picture modes, to change their analogue, do the following: a) Firstly use “ | (Picture mode) button to switch to the picture mode which you want to change. b) Enter into picture menu and adjust for suitable analogue. c) Use factory remote, press “ADJ” button to enter into “FIX1”, at this menu press “Last” button, after

refreshing the data, exit “FIX1”. The analogue in this picture mode has been changed.

6 For software (V1.0) alignment instruction This software not include NICAM & IGR, it has eight OSD languages including English French German Spanish Indonesian Russian Arabic Persian, and Europe 10 Page teletext (West Europe, East Europe,Turkey/Greek, Cyrillic, Arabic/Hebrew five areas factory preset), and has games, calendar, Hotel mode, Child Lock, 255 channel preset function etc. The following are factory adjustment menu instructions:


Press ->|<-” button, before picture mode status character display disappears, in turn press the password “9”, “8”, “7”, “1”, or use factory remote RC-K20 (RC-K11 is also OK), directly press and hold “ADJ” button for a long time.

9

b) Exit method Press MENU button to enter into FIX 5 (can check version number), press ”MENU” button again to exit. Or continually press “ADJ” button on the factory remote for three times to exit.


d) Only the following personnel have the right to change: Alignment personnel, service personnel, technicians and designer.

Chart 4 FIX 1 setting Item Name Range Software default value

00 RF Delay 00-7F 35

01 VIF VCO 00-3F 27

02 Video Gain 00-07 07

03 Audio ATT 00-7F 58

04 Y DL Time 00-03 03

05 SECAM R 00-0F 07

06 SECAM B 00-0F 07

07 H VCO 00-07 04

08 H Phase 00-1F 15

09 V Shift 00-07 00

0A V Size 00-3F 2E

0B SubContras 00-1B 1B

0C SubBright 00-1B 10

0D SubTint 00-1B 10

Note 1: 01 item VIF VCO is CPU auto adjustment item, use Volume up/down button to activate.

Note 2: 08, 09, 10 items’ value will be different in 60Hz/50Hz.


Press “->|<-” button, before picture mode status character display disappears, in turn press the password 9 , 8 , 7 , 2”, or directly press and hold “ADJ” button on the factory remote for a long time to enter

into FIX 1, press ADJ button again to enter into FIX 2. b) Exiting method

Press MENU button, or press “ADJ” button on the factory remote for two times to exit. c) Adjustment method

Use Channel up/down button to select, volume up/down button to adjust. d) Only the following personnel have the right to change:

Alignment personnel, service personnel, technicians and designer. e) BUS OFF” mode, used to auto adjust computer white balance. Directly press and hold “STOP” button on

the factory remote for a long time to enter, BUS OFF” will be displayed. The bus off is auto adjusted by computer white balance. After adjustment press “STOP” button on the factory remote again to exit, and it will display BUS On” relevant information.


Item Name Range Default value Driving address

(M6120x)

Store address

(24c08)

00 Service SW 00-01 00 Slave BAh Slave A0h

01 Drive R 00-7F 3F 0B 2B

10

02 Drive B 00-7F 3F 0C 2C

03 Cut Off R 00-FF 7F 0D 2D

04 Cut Off G 00-FF 7F 0E 2E

05 Cut Off B 00-FF 7F 0F 2F


Press ->|<- button, before picture mode status character display disappears, in turn press the password 9 , 3 , 7 , 3”.

b) Exiting method Press MENU” button, or press “ADJ” button on the factory remote for two times to exit.

c) Adjustment method Use Channel up/down button to select, volume up/down button to adjust.

d) Only the designer have the right to change! e) All the items correspond to M61205/8 specifications. And the last one is reading status. Among them

10H’s last three digit is picture IF selection, 000 38MHz/001 38.9MHz /010 39.5MHz etc.


Press ->|<- button, before picture mode status character display disappears, or in Heat Run status, in turn press the password 9 , 4 , 7 , 4 , or directly press and hold “STILL” button on the factory remote for a long time.

b) Exit method Press MENU button, or press “ADJ” button on the factory remote for two times to exit.

c) Adjustment method Use Channel up/down button to select, volume up/down button to adjust.

d) Only the service personnel and technicians and designer have the right to change.


Item Name Select

Software

default

value

Remarks

00 Heat Run On/Off <Off> When On is selected, “Heat Run” will be displayed at all times.

At this time, the remote operation will be ineffective (Only digit

buttons effect when pressing long time, and temporarily exit

Heat Run ),the function of auto-power-off when no signal is

ineffective, ON/OFF timer is cancelled, blue background

function is cancelled, press the power switch, the power is

supplied immediately. To exit Heat Run , should press

password “9”, “4”, 7”, 4”, enter into FIX 4 and select Off to

turn off.

01 Power Memory On/Off <On> When On is selected, the set will be in standby or working

when pressing power switch (Depending on the TV status when

turning off). When Off is selected, the set will be in standby

when pressing power switch.

02 Net input Yes/No <No> When Yes is selected, used as net TV, AV2 will display NET

and in Y/C input mode.

11

03 Blue Back On/Off <No> When On is selected, blue background will be displayed when

no input signal.

04Channel Number

255/85 <85>Select 255 channels or 85 channels. The corresponding

EEPROM is 24C08 or 24C04.

05 One Chip Type M61208/

M61205<M61205>

Select the main IC as M61208 or M61205, and M61208 has

SECAM system.

06 OSD Language 1111,11111 1111,11111

There are eight in all, every digit corresponds to English French

German Spanish Indonesian Russian Arabic Persian. If 0, then

not display the language; if 1, then display the language. The

software default value is 1111,1111 (all selected)

West Europe English, German, French, Italian, Hungarian

East Europe Polish German, French, Italian, Hungarian

Turkey/Greek Turkey, Greek, English, German

Cyrillic Russian, Ukranian

Arabic/Hebrew Arabic, Hebrew

07 TextLanguage

No TeleText

West

Europe

TeleText not use

<DK DK>

I I

BG BG 08 SoundSys Opt DK DK

MN MN

Select two sound system, the first one is a prior system

(correspondingly CPU Pin50 is high level), if only one sound

system, then both should set to same.

09 Game Yes/No Game select: if Yes, game is selected, if No, then no game.

10 Calendar Yes/NoCalendar select: Yes means select calendar; No means no

calendar.

6.5 FIX 5 setting The following is software version information: XOCECO Logo SDA5553EUR1 Model Ver. 1.0 Version 02/07/2002 Date

6.6 Standard , Vivid , Soft are three preset picture modes, if want to change their analogue, do the following:

a) Firstly use ->|<- button to switch to the picture mode which you want to change. d) Enter into picture menu adjust for suitable analogue. c) Use factory remote, press ADJ button to enter into FIX1”, in this menu press Last button. After

refreshing the data, exit FIX1”, then this picture mode’s analogue has been changed. 6.7 Hotel/Child Lock mode on/off a) Enter method

Press ->|<- button, before picture mode status character display disappears, in turn press the password 4 , 3 , 2 , 1”.

b) Exiting method Press “MENU” button or press “DSP” button to exit.

c) Adjustment method Use channel up/down, volume up/down button.

1) This function is only for parents or hotel personnel to use. 2) In Hotel mode, the maximum volume is 60 and there is no Search menu. 3) In Child Lock mode, the picture is shielded and the screen is dark.

Service Mode Orion t2129mtx 163

Documents

Transcript of Service Mode Orion t2129mtx 163