4-1

4. Disassembly and Reassembly

4-1. Disassembly and Reassembly of Q35

- This document cannot be used without Samsung's authorization -

Part Figure Description

Main

System

1. Make sure to separate the AC adapter andbattery before disassembling the system.2. Slide the knob all the way to the end in thedirection of the arrows (1) and push the batteryin the direction of the arrows (2).

3. If you push the battery upwards, the batteryis separated.

4. Remove the screws from the bottom.

5. Remove the HDD compartment cover.6. Remove the memory compartment cover.7.Remove the minicard compartment cover.

4-2

4. Disassembly and Reassembly

- This document cannot be used without the authorization of Samsung -

Part Figure Description

Main

System

8. When removing the HDD compartment cover,you will find the HDD. Separate the HDD cableand lift up the HDD at an angle of 70º asshown in the figure.(To separate the HDD cable, lift up the cableconnector.)*CautionDo not lift the HDD up using excessive force.Make sure to remove the HDD before turningover the system.

9.Separate the ODD as the figure shows.

10.Remove screws fixed up TOP and BOTTOMas the figure shows.

11.Push the hooks inwards using tweezers asthe figure shows and lift up the keyboard.*CautionAvoid scratching the Top when pushing thehook with the tweezers.

4-3

4. Disassembly and Reassembly

- This document cannot be used without the authorization of Samsung -

Part Figure Description

Main

System

12. Lift up the keyboard, then the ConnectorLock and separate the FPC.

13.1) Lift left side first.2) Separate Cap-Top lower side to 2 of 3

4) Separate Cap-Top lower side fully

5)

Caution : Be careful to happen scratch on LCD-Front because of excessive force when youdisassemble Hinge-Cap area.

14. Separate the whole Cap-top.

15. Disconnect the antenna cable connected tothe wireless LAN and take the cable out in thedirection of the arrow. (1: Aux,2: Main)

4-4

4. Disassembly and Reassembly

- This document cannot be used without the authorization of Samsung -

Part Figure Description

Main

System

16. Hold and pull the black and white cable infigure through guideline.

17. Lift up the Assy LCD slightly and separate itby pulling it in the direction of the arrow.

16. Remove the 2 screws fixing the Hinge andthe Top.

19. Separate the LCD cable from MainBD.

4-5

4. Disassembly and Reassembly

- This document cannot be used without the authorization of Samsung -

Part

NameFigure Description

Main

System

20. (1) Separate the Ontop cable from theMain board.(2)Separate the FFC-touchpad from MainBD.

21. Lift up the Cable in figure and separateLCD from system.

22.Separate TOP from system as the figureshows.23.Disconnect fan connector and speakerconnector from MainBD.24.Remove the screws fixed up MainBD andBottom.25.Remove screws fixed up the DMB moduleand MainBD.

4-6

4. Disassembly and Reassembly

- This document cannot be used without the authorization of Samsung-

Part Figure Description

Main

System

26.Separate DMB module from MainBD as thefigure shows.

27.Remove the screws fixed up the BRKT-DMBand BOTTOM.28.Remove the screws fixed up the FAN andBOTTOM.

29.Separated BOTTOM is the figure shows.

4-7

4. Disassembly and Reassembly

- This document cannot be used without the authorization of Samsung -

Part

NameFigure Description

Main

System

30. Remove the screw fixing the Fan, separatethe Fan.

31.Turn the screw on the CPU socket 180degrees in the direction of the arrow with a (-)screwdriver.

32. Separate the CPU from the socket.

33.Separate wireless card as the figure shows.

4-8

4. Disassembly and Reassembly

- This document cannot be used without the authorization of Samsung -

Part

NameFigure Description

LCD

Ass'y

1. Remove the Rubber Foot from the positionsindicated by the arrows in the figure, thenremove the screws.

2. Insert your finger between the LCD Panel andthe LCD Front, then separate the lower part ofthe LCD Front.3. Slide the latch with your finger to preventintervention with the LCD Front and insert yourfinger between the LCD Panel and LCD Front toseparate the upper part of the LCD Front.4. Separate both sides of the LCD Front.*CautionDo not separate the LCD Front with excessiveforce.

5. Remove the screws indicated by the arrowsin the figure.

6.Separate the LCD-inventor as the figures.

4-9

4. Disassembly and Reassembly

- This document cannot be used without the authorization of Samsung -

Part Figure Description

LCD

Ass'y

7.Separate the inventor board connector as thefigure shows.8.Remove the LCD Bracket

9.Lift up LCD module.

10.Lift up the LCD Bracket11.Remove the screws fixed up the LCD Backand Hinge.12.Separate the left and right hinges.

13.Remove the antenna wire as the figureshows.

4-10

4. Disassembly and Reassembly

- This document cannot be used without the authorization of Samsung-

Part Figure Description

LCD

Ass'y

14. Remove the silver tapes in circles 1 and 2.

15. Pull out the LCD cable in circle 1 in thedirection of the arrow.

4-11

4. Disassembly and Reassembly

- This document cannot be used without the authorization of Samsung-

Part Figure Description

TOP

Ass'y

1.Disconnect the power-BD connector frompower board2.Remove the screws on TOP and separatepower-BD Bracket-support_l andBracket_support_r from TOP.

3.Remove the screws fixed up Brkt-touchpadand TOP.4.Disconnect FFC-touchpad as the figure showsand remove the bracket-touchpad.

5.Remove the Touchpad-BD from TOP as thefigure shows.