InformationMerloni Elettrodomestici UK Ltd

© 2003 Reg. Office: Peterborough PE2 9JB. Registered in London: 106725

Service

CompressorGuide

Types Covered:-

ASPERADANFOSSELECTROLUXEMBRACOMATSUSHITAZEM~~~~~~~~~~~~~~~~~~~~~~~

5407048 Issue 1 August 2003

2

Health & Safety Information applicable to Servicing Refrigeration Products containing Isobutane Refrigerant R600a

GeneralThe following Health & Safety instructions are an addition to other Company Health Safety Procedures already published:-

1. Only engineers who have been trained on the safe handling of Isobutane R600a refrigerant are authorised to transport, store or carry out system repairs.

2. This manual is not intended as a comprehensive repair/maintenance guide to the appliance.

3. It should only be used by suitably qualified persons having technical competence, applicable product knowledge, suitable tools and test equipment.

4. Servicing of electrical appliances must be undertaken with the appliance disconnected. (unplugged from the electrical supply).

5. Servicing must be preceded by earth continuity and insulation checks, plus refrigerant leak detection - refer to page 13.

6. Personal safety precautions must be taken to protect against accidents caused by sharp edges on metal and plastic parts.

7. After servicing, the appliance must be rechecked for electrical safety.

8. Smoking, naked flames, or operating gas and/or electrical equipment (including cordless power tools) are forbidden within the storage area, working area and vehicles used to transport Isobutane.

9. The carrying case for the scales and refrigerant must display a red flammability label Part Number 8100063 which should be visible and readable at all times.

10. The vehicle and storage area must be ventilated as far as is reasonably practicable and the aluminium case kept out of direct sunlight. The storage temperature of Isobutane should not exceed 50ºC.

11. The vehicle transporting Isobutane (R600a) refrigerant must display a Red Flammable Gas warning sticker (Part Number 8100063).

12. Engineers should not wear clothes that are liable to cause static discharge ("electrostatic sparking").

13. Avoid working in small rooms.

14. Do not work in cellars.

15. Whenever possible move the appliance into a larger open area away from possible ignition sources.

16. Request the customer to turn off all other electrical and gas appliances in the near vicinity of the repair and note that it is done. Customers should be advised to restrict activity within the near vicinity for a short time.

17. Isobutane refrigerant must be vented to atmosphere, (outside of the premises e.g. via open window through the clear plastic hose supplied).

Continued....

3

Health & Safety Information applicable to Servicing Refrigeration Products containing Isobutane Refrigerant R600a

18. Isobutane is heavier than air and must not be vented within 3 metres of the following: sewer cover, cellar, drain or any similar construction lower than ground level, boiler air inlet/outlet, or near any possible source of ignition.

19. Working with a naked flame i.e. soldering or brazing is forbidden. Unless otherwise stated, pipework connections must only be made using the Lokring coupling system.

20. Electronic leak detectors with high voltage tips must NOT be used with any Isobutane (R600a).

21. All equipment used for this activity must be checked regularly and maintained in a safe working condition; parts must be replaced as required.

Health & Safety Information Applicable to Servicing RefrigerationContaining R134a

General1. This manual is not intended as a comprehensive repair/maintenance guide to the appliance.2. It should only be used by suitably qualified persons having technical competence, applicable product

knowledge, suitable tools and test equipment.3. Servicing of electrical appliances must be undertaken with the appliance disconnected (unplugged

from the electrical supply).4. Servicing must be preceded by earth continuity and insulation checks.5. Personal safety precautions must be taken to protect against accidents caused by sharp edges on

metal and plastic parts.6. After servicing, the appliance must be rechecked for electrical safety.

Refrigerant R134a - Safe Handling - Transporting & Storage1. Work areas should be well ventilated and any immediate heat sources turned off.2. Do not smoke where there is a possibility of refrigerant in the atmosphere. Customer/s should also

be advised.3. Cylinders must not have heat applied, or stand close to a heat source, and should be stored out of

direct sunlight.4. Should a sudden release of refrigerant occur, open windows or outside doors in the immediate

vicinity, then evacuate for a few minutes.5. It is illegal to intentionally vent R134a refrigerant to atmosphere. Follow the Company procedure on

collection and reclamation.6. If a leak is identified, the appliance must be repaired immediately if possible.7. Where it is not possible to repair an appliance immediately, the customer should be advised.

The appliance should be turned off and the refrigerant recovered.8. Returned compressors must be sealed to prevent the escape of oil and refrigerant. Refer to the

Environmental responsibilities for service engineers in your Health and Safety booklet.9. Cylinders (R134a) being transported must be in an upright position on the floor of the vehicle and

prevented from movement.10. A Green compressed gas label Part No. 8100062 should be displayed on the rear of the vehicle.

Originator - A. Flood, Service Technical Engineer

4

Introduction

The purpose of this manual is to assist engineers graphically with identifying compressors and their associated components. This is necessary because compressors for a particular model can change over-night and Partfinder2 in most instances shows the compressor and parts used during manufacture only. Some of the compressors currently fitted to appliances are no longer available or are superseded to a kit, nevertheless this information will identify the PTC, Overload or Dissipator. A basic wiring diagram is also included for each compressor.

INDEX

Aspera BPM1058Z. . . . . . . . . . . . 5Aspera BPM1072Z. . . . . . . . . . . . 6Aspera BPM1084Z. . . . . . . . . . . . 7Aspera BPM1111Z. . . . . . . . . . . . 8Aspera NBU1114Y. . . . . . . . . . . . 9Aspera NBU1115Y. . . . . . . . . . . . 10Aspera NBU1116Y. . . . . . . . . . . . 11

Danfoss NL6F . . . . . . . . . . . . . . . 12Danfoss NL11F . . . . . . . . . . . . . . 13Danfoss SC18F . . . . . . . . . . . . . . 14Danfoss TLES5F . . . . . . . . . . . . . 15Danfoss TLES5KK2 . . . . . . . . . . . 16

Electrolux GD36AA . . . . . . . . . . . 17Electrolux GLY45AA . . . . . . . . . . 18

Embraco EMT36H . . . . . . . . . . . . 19Embraco EMT36HLP . . . . . . . . . . 20Embraco EMT43HLP . . . . . . . . . . 21Embraco EMT49H . . . . . . . . . . . . 22Embraco EMT49HLP . . . . . . . . . . 23Embraco EMY32CLC. . . . . . . . . . 24Embraco EMY32CLC. . . . . . . . . . 25

Matsushita D110C21RA . . . . . . . 26Matsushita D110C21RBX5 . . . . . 27Matsushita D91C18RA . . . . . . . . 28Matsushita DB77C14RAY5 . . . . . 29Matsushita DB91C . . . . . . . . . . . 30Matsushita SB43C. . . . . . . . . . . . 31Matsushita SB43L . . . . . . . . . . . . 32Matsushita SD51C10WAY5 . . . . 33Matsushita SD51E60RAW5 . . . . 34

ZEM GL45AA . . . . . . . . . . . . . . . 35ZEM GL50AA . . . . . . . . . . . . . . . 36ZEM GL60AA . . . . . . . . . . . . . . . 37ZEM GL75AH . . . . . . . . . . . . . . . 38ZEM GL80AA . . . . . . . . . . . . . . . 39ZEM GL90AA . . . . . . . . . . . . . . . 40ZEM GL90AH . . . . . . . . . . . . . . . 41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

COMPRESSOR GUIDE

5407048 ~ Page 5 of 41

ASPERA BPM1058ZCOMPRESSOR PART/KIT No: 2503179

PTC / START DEVICE: 2503177 incl. Overload & Terminal BlockOVERLOAD: -----

TERMINAL BLOCK: 2603374 - Not Available - See PTC above.COVER: -----

DISSIPATOR: 2503183CAPACITOR: -----

START WINDING: 36.1 OhmsRUN WINDING: 32.7 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 6 of 41

ASPERA BPM1072ZCOMPRESSOR PART/KIT No: 2501585

PTC / START DEVICE: 257013OVERLOAD: 2501591

TERMINAL BLOCK: -----COVER: N/A

DISSIPATOR: 2120310CAPACITOR: -----

START WINDING: 33.4 OmsRUN WINDING: 32 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 7 of 41

ASPERA BPM1084ZCOMPRESSOR PART/KIT No: 2503249

PTC / START DEVICE: 2503316 Incl. OverloadOVERLOAD: -----

TERMINAL BLOCK: 2603374 - Not Available - See PTC above.COVER: -----

DISSIPATOR: -----CAPACITOR: -----

START WINDING: 39.1 OhmsRUN WINDING: 27.9 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 8 of 41

ASPERA BPM1111ZCOMPRESSOR PART/KIT No: 2503469

PTC / START DEVICE: 2503468 includes OverloadOVERLOAD: 2503468

TERMINAL BLOCK: 2603374 - Not Available - See PTC above.COVER: -----

DISSIPATOR: -----CAPACITOR: -----

START WINDING: 40.6 OhmsRUN WINDING: 17.5 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 9 of 41

ASPERA NBU1114YCOMPRESSOR PART/KIT No: 2603348

PTC / START DEVICE: 2603042OVERLOAD: 2603347

TERMINAL BLOCK: 2603374 - Not AvailableCOVER: 2601473

DISSIPATOR: 2602889CAPACITOR: 2602848 (4 uF)

START WINDING: 19.7 OhmsRUN WINDING WINDING: 19.6 Ohms

REFRIGERANT CHARGE TYPE: R600a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 10 of 41

ASPERA NBU1115YCOMPRESSOR PART/KIT No: 2603072

PTC / START DEVICE: 2603042OVERLOAD: 2603073

TERMINAL BLOCK: 2603374 - Not AvailableCOVER: 2601473

DISSIPATOR: -----CAPACITOR: 2602848 (4 uF)

START WINDING: 15.2 OhmsRUN WINDING: 16 Ohms

REFRIGERANT CHARGE TYPE: R600a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 11 of 41

ASPERA NBU1116YCOMPRESSOR PART/KIT No: 2603289

PTC / START DEVICE: 2603042OVERLOAD: 2603073

TERMINAL BLOCK: 2603374 - Not AvailableCOVER: 2601473

DISSIPATOR: 2602889CAPACITOR: 2602848 (4 uF)

START WINDING: 15.2 OhmsRUN WINDING: 16 Ohms

REFRIGERANT CHARGE TYPE: R600a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 12 of 41

DANFOSS NL6FCOMPRESSOR PART/KIT No: 2502074

PTC / START DEVICE: 2502073OVERLOAD: INTERNAL

TERMINAL BLOCK: -----COVER: 2600409

DISSIPATOR: -----CAPACITOR: N/A

START WINDING: 13.6 OhmsRUN WINDING: 16 Ohms

REFRIGERANT CHARGE TYPE: R134a

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

9.5mm 9.5mm 8.0mm

COMPRESSOR GUIDE

5407048 ~ Page 13 of 41

DANFOSS NL11FCOMPRESSOR PART/KIT No: 2600747

PTC / START DEVICE: 2502346OVERLOAD: -----

TERMINAL BLOCK: -----COVER: 2502348

DISSIPATOR: -----CAPACITOR: 2502341

START WINDING: 14.7 OhmsRUN WINDING: 8.2 Ohms

REFRIGERANT CHARGE TYPE: R134a

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

11.0mm 9.5mm 9.5mm

COMPRESSOR GUIDE

5407048 ~ Page 14 of 41

DANFOSS SC18FCOMPRESSOR PART/KIT No: No Longer Available

PTC / START DEVICE: 2502347OVERLOAD: -----

TERMINAL BLOCK: -----COVER: 2502349

DISSIPATOR: -----CAPACITOR: 2502490

START WINDING: 13.7 OhmsRUN WINDING: 5.0 Ohms

REFRIGERANT CHARGE TYPE: R134a

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

11 mm 9.5 mm 9.5 mm

COMPRESSOR GUIDE

5407048 ~ Page 15 of 41

DANFOSS TLES5FCOMPRESSOR PART/KIT No: 2502150

PTC / START DEVICE: 256238OVERLOAD: INTERNAL

TERMINAL BLOCK: -----COVER: 2600409

DISSIPATOR: 256236CAPACITOR: -----

START WINDING: 15.3 OhmsRUN WINDING: 18.9 Ohms

REFRIGERANT CHARGE TYPE: R134a

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

9.5mm 9.5mm 8.0mm

COMPRESSOR GUIDE

5407048 ~ Page 16 of 41

DANFOSS TLES5KK2COMPRESSOR PART/KIT No: 2603390

PTC / START DEVICE: 2603371OVERLOAD: -----

TERMINAL BLOCK: -----COVER: 2603373

DISSIPATOR: -----CAPACITOR: -----

START WINDING: 16 OhmsRUN WINDING: 26 Ohms

REFRIGERANT CHARGE TYPE: R600a

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

9.5mm 9.5mm 8.0mm

COMPRESSOR GUIDE

5407048 ~ Page 17 of 41

ELECTROLUX GD36AACOMPRESSOR PART/KIT No: 2502226

PTC / START DEVICE: 2502378OVERLOAD: 2502379

TERMINAL BLOCK: 2502375COVER: 2502373

DISSIPATOR: 2502227CAPACITOR: N/A

START WINDING: 25 OhmsRUN WINDING: 31 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.5mm 8.5mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 18 of 41

ELECTROLUX GLY45AACOMPRESSOR PART/KIT No: 2502822

PTC / START DEVICE: 2502820OVERLOAD: -----

TERMINAL BLOCK: 2502819COVER: 2502818

DISSIPATOR: 2601482CAPACITOR: N/A

START WINDING: 21 OhmsRUN WINDING: 22 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 19 of 41

EMBRACO EMT36HCOMPRESSOR PART/KIT No: Refer to relevant model on Part Finder

PTC / START DEVICE: 2601474OVERLOAD: 2601517

TERMINAL BLOCK: 2601472COVER: 2601473

DISSIPATOR: 2601482CAPACITOR: 2601480 (2.5 uF)

START WINDING: 30 OhmsRUN WINDING: 25 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 7.0mm 6.0mm

COMPRESSOR GUIDE

5407048 ~ Page 20 of 41

EMBRACO EMT36HLPCOMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: 2601474OVERLOAD: 2601517

TERMINAL BLOCK: 2601472COVER: 2601473

DISSIPATOR: 2602821CAPACITOR: 2602882 (2.5 uF)

START WINDING: 29.5 OhmsRUN WINDING: 25 Ohms

REFRIGERANT CHARGE TYPE: R134a

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 7.0mm 6.0mm

COMPRESSOR GUIDE

5407048 ~ Page 21 of 41

EMBRACO EMT43HLPCOMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: 2601474OVERLOAD: 2601517

TERMINAL BLOCK: 2601472COVER: 2601473

DISSIPATOR: 2602821CAPACITOR: 2601480 (2.5 uF)

START WINDING: 24 OhmsRUN WINDING: 22 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 7.0mm 6.0mm

COMPRESSOR GUIDE

5407048 ~ Page 22 of 41

EMBRACO EMT49HCOMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: 2601474OVERLOAD: 2601475

TERMINAL BLOCK: 2601472COVER: 2601473

DISSIPATOR: 2601482CAPACITOR: 2601480 (2.5uF)

START WINDING: 32 OhmsRUN WINDING: 19 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 7.0mm 6.0mm

COMPRESSOR GUIDE

5407048 ~ Page 23 of 41

EMBRACO EMT49HLPCOMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: 2601474OVERLOAD: 2601475

TERMINAL BLOCK: 2601472COVER: 2601473

DISSIPATOR: 2602821CAPACITOR: 2601480 (BOLT IN), 2602882 (CLIP IN) (2.5

uF)START WINDING: 32 Ohms

RUN WINDING: 19 OhmsREFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 7.0mm 6.0mm

COMPRESSOR GUIDE

5407048 ~ Page 24 of 41

EMBRACO EMY32CLCCOMPRESSOR PART/KIT No: 2602871 - No Longer Available

Refer to relevant model on PartfinderPTC / START DEVICE: 2603042

OVERLOAD: 2603044TERMINAL BLOCK: 2603374 - Not Available

COVER: 2601473DISSIPATOR: 2602889CAPACITOR: 2602873 (2.5uF)

START WINDING: 34 OhmsRUN WINDING: 43 Ohms

REFRIGERANT CHARGE TYPE: R600a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 7.0mm 6.0mm

COMPRESSOR GUIDE

5407048 ~ Page 25 of 41

EMBRACO EMY32CLCCOMPRESSOR PART/KIT No: 2603397

PTC / START DEVICE: 2603042OVERLOAD: 2603044

TERMINAL BLOCK: 2603374 - Not AvailableCOVER: 2601473

DISSIPATOR: 2603391CAPACITOR: 2602873 (2.5uF)

START WINDING: 34 OhmsRUN WINDING: 43 Ohms

REFRIGERANT CHARGE TYPE R600a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 7.0mm 6.0mm

COMPRESSOR GUIDE

5407048 ~ Page 26 of 41

MATSUSHITA D110C21RACOMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: Device and Overload: 2600340OVERLOAD: -----

TERMINAL BLOCK: -----COVER: 2600338

DISSIPATOR: -----CAPACITOR: -----

START WINDING: 18.3 OhmsRUN WINDING: 8.5 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 27 of 41

MATSUSHITA D110C21RBX5COMPRESSOR PART/KIT No: Refer to the relevant model on Partfinder

PTC START DEVICE: WR7X263OVERLOAD: WR08X0198

TERMINAL BLOCK: -----COVER: -----

DISSIPATOR: -----CAPACITOR: -----

START WINDING: 18 OhmsRUN WINDING: 7.0 Ohms

REFRIGERANT CHARGE TYPE: R134a

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 28 of 41

MATSUSHITA D91C18RACOMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: 2600340 Incl. OVERLOADOVERLOAD: N/A

TERMINAL BLOCK: N/ACOVER: 2600338

DISSIPATOR: N/ACAPACITOR: 2601705 (6 uF)

START WINDING: 21 OhmsRUN WINDING: 8.5 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 29 of 41

MATSUSHITA DB77C14RAY5COMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: 2601671 Incl. OVERLOADOVERLOAD: N/A

TERMINAL BLOCK: N/ACOVER: 2601672

DISSIPATOR: N/ACAPACITOR: 2601796 (5 uF)

START WINDING: 11.5 OhmsRUN WINDING: 16.5 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 30 of 41

MATSUSHITA DB91CCOMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: 2600340OVERLOAD: -----

TERMINAL BLOCK: -----COVER: 2601672

DISSIPATOR: -----CAPACITOR: 2601705 WHERE FITTED

START WINDING: 10 OhmsRUN WINDING: 13 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 31 of 41

MATSUSHITA SB43CCOMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: 2601554OVERLOAD: INTERNAL

TERMINAL BLOCK: -----COVER: 2600480

CAPACITOR: 2601558 (2.5uF)START WINDING: 19 Ohms

RUN WINDING: 31 OhmsREFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 32 of 41

MATSUSHITA SB43LCOMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: 2601554OVERLOAD: INTERNAL

TERMINAL BLOCK: -----COVER: 2600480

DISSIPATOR: 282611CAPACITOR: 2601558 (2.5uF)

START WINDING: 19 OhmsRUN WINDING: 31 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 33 of 41

MATSUSHITA SD51C10WAY5COMPRESSOR PART/KIT No: Refer to relevant model on Partfinder

PTC / START DEVICE: 2601554OVERLOAD: INTERNAL

TERMINAL BLOCK: -----COVER: 2600480

DISSIPATOR: 282611CAPACITOR: 2601558 (2.5uF)

START WINDING: 30 OhmsRUN WINDING: 16 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 34 of 41

MATSUSHITA SD51E60RAW5COMPRESSOR PART/KIT No: 2602845

PTC / START DEVICE: 2603008OVERLOAD: INTERNAL

TERMINAL BLOCK: -----COVER: 2603009

DISSIPATOR: 2602840CAPACITOR: -----

START WINDING: 28 OhmsRUN WINDING: 27 Ohms

REFRIGERANT CHARGE TYPE: R600a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 7.0mm 6.0mm

COMPRESSOR GUIDE

5407048 ~ Page 35 of 41

ZEM GL45AACOMPRESSOR PART/KIT No: 2073418

PTC / START DEVICE: 2503733OVERLOAD: 2503735

TERMINAL BLOCK: 2503730COVER: 2503731 / 2503732

DISSIPATOR: 2502929CAPACITOR: -----

START WINDING: 24 OhmsRUN WINDING: 21 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 36 of 41

ZEM GL50AACOMPRESSOR PART/KIT No: 2073417

PTC / START DEVICE: 2503733OVERLOAD: 2503735

TERMINAL BLOCK: 2503730COVER: 2503731 / 2503732

DISSIPATOR: 2502929CAPACITOR: -----

START WINDING: 25 OhmsRUN WINDING: 19.7 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 37 of 41

ZEM GL60AACOMPRESSOR PART/KIT No: 2073416

PTC / START DEVICE: 2503733OVERLOAD: 2503842

TERMINAL BLOCK: 2503730COVER: 2503731 / 2503732

DISSIPATOR: 2502929CAPACITOR: -----

START WINDING: 24 OhmsRUN WINDING: 17 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 38 of 41

ZEM GL75AHCOMPRESSOR PART/KIT No: 2073405 - No Longer Available

PTC / START DEVICE: 2600106OVERLOAD: 2600700

TERMINAL BLOCK: 2600107COVER: 2600108

DISSIPATOR: 2600758CAPACITOR: 2600415 or 2600896 - REFER TO MODEL

START WINDING: 24 OhmsRUN WINDING: 17 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 39 of 41

ZEM GL80AACOMPRESSOR PART/KIT No: 2073415

PTC / START DEVICE: 2503733OVERLOAD: 2503737

TERMINAL BLOCK: 2503730COVER: 2503731/2503732

DISSIPATOR: 2502929CAPACITOR: -----

START WINDING: 21 OhmsRUN WINDING: 12 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 40 of 41

ZEM GL90AACOMPRESSOR PART/KIT No: 2073414

PTC / START DEVICE: 2503733OVERLOAD: 2503736

TERMINAL BLOCK: 2503730COVER: 2503731/2503732

DISSIPATOR: 2502929CAPACITOR: -----

START WINDING: 22.8 OhmsRUN WINDING: 9.2 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm

COMPRESSOR GUIDE

5407048 ~ Page 41 of 41

ZEM GL90AHCOMPRESSOR PART/KIT No: 2502105

PTC / START DEVICE: 2503753OVERLOAD: 2503752

TERMINAL BLOCK: 2503754COVER: 2503755

DISSIPATOR: -----CAPACITOR: 2600745 1WHERE FITTED

START WINDING: 17 OhmsRUN WINDING: 10 Ohms

REFRIGERANT CHARGE TYPE: R134a

Live & Neutral shown is the most common configuration.This configuration may not be followed by all manufacturers products.

COMPRESSOR STUB DIAMETER

SUCTION PROCESS DISCHARGE

8.0mm 8.0mm 7.0mm