SERVICE MANUAL Brand Company, D&M Holdings lnc. e Ver. 1 SERVICE MANUAL BLU-RAY DISC/DVD VIDEO...

Denon Brand Company, D&M Holdings lnc.

e

Ver. 1

SERVICE MANUAL

BLU-RAY DISC/DVD VIDEO TRANSPORT

MODEL JP E3 E2 EK E2A E1C E1K EUT

DVD-2500BTCI

● For purposes of improvement, specifications and design are subject to change without notice.

● Please use this service manual with referring to the operating instructions without fail.

● Some illustrations using in this service manual are slightly different from the actual set.

注　意サービスをおこなう前に、このサービスマニュアルを必ずお読みください。本機は、火災、感電、けがなどに対する安全性を確保するために、さまざまな配慮をおこなっており、また法的には「電気用品安全法」にもとづき、所定の許可を得て製造されております。従ってサービスをおこなう際は、これらの安全性が維持されるよう、このサービスマニュアルに記載されている注意事項を必ずお守りください。

●本機の仕様は性能改良のため、予告なく変更することがあります。

●補修用性能部品の保有期間は、製造打切後 8年です。

●修理の際は、必ず取扱説明書を参照の上、作業を行ってください。

●本文中に使用しているイラストは、説明の都合上現物と多少異なる場合があります。

X0374 V.01 DE/CDM 0801

2DVD-2500BTCI

--- MEMO---

3DVD-2500BTCI

Please heed the points listed below during servicing and inspection.

◎Heed the cautions!Spots requiring particular attention when servicing, such asthe cabinet, parts, chassis, etc., have cautions indicated onlabels or seals. Be sure to heed these cautions and the cau-tions indicated in the handling instructions.

◎Caution concerning electric shock!(1) An AC voltage is impressed on this set, so touching inter-

nal metal parts when the set is energized could causeelectric shock. Take care to avoid electric shock, by for ex-ample using an isolating transformer and gloves whenservicing while the set is energized, unplugging the powercord when replacing parts, etc.

(2)There are high voltage parts inside. Handle with extra carewhen the set is energized.

◎Caution concerning disassembly and assembly!Though great care is taken when manufacturing parts fromsheet metal, there may in some rare cases be burrs on theedges of parts which could cause injury if fingers are movedacross them. Use gloves to protect your hands.

◎Only use designated parts!The set's parts have specific safety properties (fire resis-tance, voltage resistance, etc.). For replacement parts, besure to use parts which have the same properties. In particu-lar, for the important safety parts that are marked z on wiringdiagrams and parts lists, be sure to use the designated parts.

◎Be sure to mount parts and arrange thewires as they were originally!

For safety reasons, some parts use tape, tubes or other insu-lating materials, and some parts are mounted away from thesurface of printed circuit boards. Care is also taken with thepositions of the wires inside and clamps are used to keepwires away from heating and high voltage parts, so be sure toset everything back as it was originally.

◎Cautions concerning the power supply!Current continues to flow in the set for 10 to 20 seconds afterthe power cord is unplugged. Wait until the power LED turnscompletely off before proceeding

◎ Inspect for safety after servicing!Check that all screws, parts and wires removed or discon-nected for servicing have been put back in their original posi-tions, inspect that no parts around the area that has beenserviced have been negatively affected, conduct an insulationcheck on the external metal connectors and between theblades of the power plug, and otherwise check that safety isensured.

(Insulation check procedure)Unplug the power cord from the power outlet, disconnect theantenna, plugs, etc., and turn the power switch on. Using a500V insulation resistance tester, check that the insulation re-sistance between the terminals of the power plug and the ex-ternally exposed metal parts (antenna terminal, headphonesterminal, microphone terminal, input terminal, etc.) is 1MΩ orgreater. If it is less, the set must be inspected and repaired.

Concerning important safety parts

Many of the electric and structural parts used in the set havespecial safety properties. In most cases these properties aredifficult to distinguish by sight, and using replacement partswith higher ratings (rated power and withstand voltage) doesnot necessarily guarantee that safety performance will be pre-served. Parts with safety properties are indicated as shownbelow on the wiring diagrams and parts lists is this servicemanual. Be sure to replace them with parts with the designat-ed part number.

(1) Schematic diagrams ... Indicated by the z mark.

(2) Parts lists ... Indicated by the z mark.

Using parts other than the designated partscould result in electric shock, fires or otherdangerous situations.

SAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassisresistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the powercord is less than 460 kohms, the unit is defective.

LASER RADIATIONCaution - Class 1M visible and invisible laser radiation when open.Do not view directly with optical instruments.

CAUTION

CAUTION

サービス、点検時にはつぎのことにご注意願います。

◎注意事項をお守りください！サービスのとき特に注意を必要とする個所についてはキャビネット、部品、シャーシなどにラベルや捺印で注意事項を表示しています。これらの注意書きおよび取扱説明書などの注意事項を必ずお守りください。

◎感電に注意！(1) このセットは、交流電圧が印加されていますので通電時に内部金属部に触れると感電することがあります。従って通電サービス時には、絶縁トランスの使用や手袋の着用、部品交換には、電源プラグを抜くなどして感電にご注意ください。

(2) 内部には高電圧の部分がありますので、通電時の取扱には十分ご注意ください。

◎分解、組み立て作業時のご注意！板金部品の端面の『バリ』は、部品製造時に充分管理をしておりますが、板金端面は鋭利となっている箇所が有りますので、部品端面に触れたまま指を動かすとまれに怪我をする場合がありますので十分注意して作業して下さい。手の保護のために手袋を着用してください。

◎指定部品の使用！セットの部品は難燃性や耐電圧など安全上の特性を持ったものとなっています。従って交換部品は、使用されていたものと同じ特性の部品を使用してください。特に配線図、部品表に z 印で指定されている安全上重要な部品は必ず指定のものをご使用ください。

◎部品の取付けや配線の引きまわしは、元どおりに！安全上、テープやチューブなどの絶縁材料を使用したり、プリント基板から浮かして取付けた部品があります。また内部配線は引きまわしやクランパーによって発熱部品や高圧部品に接近しないように配慮されていますので、これらは必ず元どおりにしてください。

◎電源に注意！このセットは電源プラグを抜いても、十数秒間通電していますので、電源 LEDが完全に消灯してからサービス作業を実施してください。

◎サービス後は安全点検を！サービスのために取り外したねじ、部品、配線などが元どおりになっているか、またサービスした個所の周辺を劣化させてしまったところがないかなどを点検し、外部金属端子部と、電源プラグの刃の間の絶縁チェックをおこなうなど、安全性が確保されていることを確認してください。

（絶縁チェックの方法）電源コンセントから電源プラグを抜き、アンテナやプラグなどを外し、電源スイッチを入れます。500V 絶縁抵抗計を用いて、電源プラグのそれぞれの端子と外部露出金属部［アンテナ端子、ヘッドホン端子、マイク端子、入力端子など］との間で、絶縁抵抗値が１ MΩ 以上であることを確認してください。この値以下のときはセットの点検修理が必要です。

安全上重要な部品について

本機に使用している多くの電気部品、および機構部品は安全上、特別な特性を持っています。この特性はほとんどの場合、外観では判別つきにくく、またもとの部品より高い定格（定格電力、耐圧）を持ったものを使用しても安全性が維持されるとは、限りません。安全上の特性を持った部品は、このサービスマニュアルの配線図、部品表につぎのように表示していますので必ず指定されている部品番号のものを使用願います。

(1) 配線図…zマークで表示しています。

(2) 部品表…zマークで表示しています。

指定された部品と異なるものを使用した場合には、感電、火災などの危険を生じる恐れがあります。

注　意

注　意

4DVD-2500BTCI

DIMENSION WIRE ARRANGEMENT

If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward.Otherwise, incorrect arrangement can be a cause of noise generation.

Wire arrangement viewed from the top

SPECIFICATIONS

Note:

1. Power supply: AC 120 V, 60 Hz

Item

HDMI OutputOutput jack: 19-pin HDMI terminal, 1 setHDMI (Deep Color, Dolby Digital Plus, Dolby TrueHD, DTS-HD)

5DVD-2500BTCI

LASER BEAM SAFETY PRECAUTIONS

This BD player uses a pickup that emits a laser beam.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam.

CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure.

Location: Top of BD mechanism.

Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin.

Drive Mechanism Assembly

Laser Beam Radiation

Laser Pickup

Turntable

LASER RADIATIONWHEN OPEN. DO NOT

STARE INTO BEAM.

CAUTION

6DVD-2500BTCI

Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards.

1. Clearance Distance

When replacing primary circuit components, confirm specified clearance distance (d) and (d’) between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)

Table 1: Ratings for selected area

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2. Leakage Current Test

Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.

Measuring Method (Power ON):

Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across the terminals of load Z. See Fig. 2 and the following table.

Table 2: Leakage current ratings for selected areas

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

AC Line Voltage Clearance Distance (d), (d’)

120 V ≥ 3.2 mm (0.126 inches)

AC Line Voltage Load Z Leakage Current (i) Earth Ground (B) to:

120 V 0.15 μF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA Peak Exposed accessible parts

Chassis or Secondary Conductor

Primary Circuit

Fig. 1

d' d

AC Voltmeter (High Impedance)

Exposed Accessible Part

B Earth Ground Power Cord Plug Prongs

Z

Fig. 2

7DVD-2500BTCI

STANDARD NOTES FOR SERVICING

Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is

indicated as shown.

2. For other ICs, pin 1 and every fifth pin are indicated as shown.

3. The 1st pin of every male connector is indicated as shown.

Instructions for Connectors1. When you connect or disconnect the FFC (Flexible

Foil Connector) cable, be sure to first disconnect the AC cord.

2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle.

Pb (Lead) Free SolderWhen soldering, be sure to use the Pb free solder.

How to Remove / Install Flat Pack-IC

1. Removal

With Hot-Air Flat Pack-IC Desoldering Machine:

1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)

2. Remove the flat pack-IC with tweezers while applying the hot air.

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

CAUTION:

1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.

2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)

Top View

Out In

Bottom ViewInput

5

10

Pin 1

Pin 1

FFC Cable

Connector

CBA

* Be careful to avoid a short circuit.

Fig. S-1-1

8DVD-2500BTCI

With Iron Wire:

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.

3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.

4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.

2. Installation1. Using desoldering braid, remove the solder from

the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.

2. The “●” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)

3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.

To Solid Mounting Point

Soldering Iron

Iron Wire

or

Hot Air Blower

Fig. S-1-5

Fine TipSoldering IronCBA

Flat Pack-ICTweezers

Fig. S-1-6

Example :

Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7

Presolder

CBA

Flat Pack-IC

Fig. S-1-8

9DVD-2500BTCI

Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.

1. Ground for Human Body

Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

2. Ground for Workbench

Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.

<Incorrect>

CBA

Grounding Band

Conductive Sheet orCopper Plate

1MΩ

1MΩ

<Correct>

CBA

10DVD-2500BTCI

CABINET DISASSEMBLY INSTRUCTIONS

1. Disassembly FlowchartThis flowchart indicates the disassembly steps to gainaccess to item(s) to be serviced. When reassembling,follow the steps in reverse order. Bend, route, anddress the cables as they were originally.

2. Disassembly of Main parts When replacing the main parts, see the following pro-

cedures. For more details, refer to Fig. D1~D9.

*About *[9](S-14), remove only (S-14) of Rear Panel.

Note: Be sure to unplug the power cord from the

power outlet before disassembling.

“Current continues to flow in the set for 10

to 20 seconds after the power cord is

unplugged. Wait until the power LED turns

completely off before proceeding.”

3. Disassembly Method

Part Steps[10] BE Main CBA Unit [1] [2] *[9](S-14) [10]

[11]FE Main CBA & BD MechanismAssembly

[1] [2] [3] *[9](S-14)[10] [11]

[12] Fan Holder [1] [2] *[9](S-14) [10][12]

[13] Fan Motor [1] [2] *[9](S-14) [10][12] [13]

[14] RS232C CBA [1] [2] [9] [10] [14]

[15] Power Supply CBA [1] [2] *[9](S-14) [12][15]

[16] AV CBA [1] [2] [3] [9] [10] [11][12] [13] [14] [16]

[17] Sub Microcontroller CBA [1] [2] [17]

[1] Top Cover

[6] Power SW CBA

[7] SD CBA

[3] Tray Panel

[4] Front Assembly

[8] Front Bracket

[2] Top Panel

[14] RS232C CBA

[16] AV CBA

[18] Pedestal

[15] Power Supply CBA

[17] Sub Microcontroller CBA

[9] Rear Panel

[10] BE Main CBA Unit

[11] FE Main CBA & BD Mechanism Assembly

[13] Fan Motor

[5] Front CBA

[12] Fan Holder

ID/Loc. No.

Part

Removal

Fig.No.

Remove/*Unhook/Unlock/Release/Unplug/Desolder

Note

[1] Top Cover D1 9(S-1), 2(S-2) ---

[2] Top Panel D2 10(S-3) ---

[3] Tray Panel D3 *2(L-1) 1

[4] Front Assembly D3

2(S-4), 2(S-5), (S-5a), *3(L-2), *CN2001, *CN4002

1

[5] Front CBA D4 7(S-6) ---

[6] Power SW CBA D4 2(S-7), Desolder ---

[7] SD CBA D4 2(S-8), SD PCB Holder ---

[8] Front Bracket D5 2(S-9) ---

[9] Rear Panel D5

2(S-10), 2(S-11), 2(S-12), (S-13), (S-14), 3(S-15), *CN1003

2

[10] BE Main CBA Unit D6

4(S-16), 4(S-17), 3(S-18), *CN6401,*CN7001, *CN7401,BE Scaler Holder, BE Scaler Sub Holder

2

[11]

FE Main CBA & BD Mechanism Assembly

D7 4(S-19), *CN2601 ---

[12] Fan Holder D7 2(S-20), *CN2500 ---

[13] Fan Motor D7 2(S-21) ---

[14] RS232C CBA D8 3(S-22), *CN2551,

RS232C Holder ---

[15]PowerSupply CBA

D82(S-23), 2(S-24), 2(S-25), *CN2501, Power PCB Holder

---

[16] AV CBA D8 7(S-26), *CN2503 ---

[17]SubMicrocontroller CBA

D9 4(S-27) ---

[18] Pedestal D9 3(S-28) ---

(1) (2) (3) (4) (5)

11DVD-2500BTCI

Note:

(1) Identification (location) No. of parts in the figures

(2) Name of the part

(3) Figure Number for reference

(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, CN = Connector* = Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)

(5) Refer to “Reference Notes.”

About tightening screws

When tightening screws, tighten them with the following torque.

Reference Notes

1. CAUTION 1: Locking Tabs (L-1) and (L-2) are fragile. Be careful not to break them.

1) Release three Locking Tabs (L-2).

2) Disconnect connectors CN2001, CN4002, then remove the Front Assembly.

2. CAUTION 2: When installing the BE Main CBA Unit with a screw, hold and press the BE Main CBA Unit to align the HDMI connector with the connector’s hole for HDMI on the Rear Panel.

Torque

0.45 ± 0.05 N·m

(S-2)

(S-2)

(S-1)

(S-1)

(S-1)

(S-1)

(S-1)

Fig. D1

[1] Top Cover

(S-3)

(S-3)

(S-3)(S-3)

[2] Top Panel

Fig. D2

CN2001

CN4002

(L-2)

(S-5)

(S-5)

(S-4)

(L-1)

(L-1)

(S-4)(S-5a)

[4] Front Assembly

[3] Tray Panel

Fig. D3

12DVD-2500BTCI

(S-6)

(S-6)

(S-7)

(S-8)

Lead with blue stripe

Desolder

[6] Power SW CBA

[7] SD CBA

SD PCB Holder

[5] Front CBA

Fig. D4

(S-10)

(S-10)

(S-11)(S-12)

(S-13) (S-14)

(S-15)

(S-15)

(S-15)

CN1003

[9] Rear Panel

(S-9)

(S-9)

[8] Front Bracket

Fig. D5

(S-16)

(S-16)

(S-17)

(S-17)

(S-17)

(S-18)

(S-18)(S-18)

CN6401

BE Scaler Holder

BE Scaler Sub Holder

CN7001

CN7401

Fig. D6

[10] BE Main CBA Unit

(S-19)

(S-19)

(S-19)

(S-20)

(S-20)

(S-21)

CN2500

CN2601

[11] FE Main CBA & BD Mechanism Assembly

[12] Fan Holder

[13] Fan Motor

Fig. D7

13DVD-2500BTCI

4. How to Eject Manually

1. Remove the Top Cover and the Top Panel.

2. Insert a screwdriver, etc. into the Hole A straightly so that the Portion A is pushed.

3. Pull the tray out manually and remove a disc.

(S-22)

(S-22)

(S-23)

(S-24)

Power PCB Holder

RS232CHolder

(S-24)

(S-26)(S-26)

(S-25)

CN2551

CN2501

CN2503

Fig. D8

[14] RS232C CBA

[15] Power Supply CBA

[16] AV CBA

(S-27)

Wire

(S-28)

Fig. D9

[17] Sub Microcontroller CBA

[18] Pedestal

Portion A

Hole A

Screwdriver, hexagon wrench

14DVD-2500BTCI

View from the bottom

Cautions concerning the structure

The chassis touches the patterns on the circuit board at 6 points, but these patterns are all ground patterns, so performance is not affected.

15DVD-2500BTCI

HOW TO INITIALIZE THE BLU-RAY DISC PLAYER

To put the program back at the factory-default, initialize the BD player as the following procedure.

1. Turn the power on by pressing the [POWER] button and the tray will close.

2. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. a appears on the screen.

3. Press [STOP] button on the remote control unit. Fig. b appears on the screen and Fig. c appears on the VFD.

4. To exit this mode, press [POWER OFF] button.

Fig. a

"*******" differ depending on the models.

MODEL : *******

Version : *.***

Region : * / *

EXIT: POWEREEPROM CLEAR : STOP

Fig. b


MODEL : *******

Version : *.***

Region : * / *


EEPROM CLEAR : OK

Fig. c

16DVD-2500BTCI

FIRMWARE RENEWAL MODE

1. Turn the power on and remove the disc on the tray.

2. To put the BD player into version up mode, press [9], [8], [7], [6], and [MENU/POP MENU] buttons on the remote control unit in that order. The tray will open automatically. Fig. a appears on the screen and Fig. b appears on the VFD.

The BD player can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open.

3. Load the disc for version up.

4. The BD player enters the F/W version up mode automatically. Fig. c appears on the screen and Fig. d appears on the VFD. If you enter the F/W for different models, “Disc Error” will appear on the screen, then the tray will open automatically.

The appearance shown in (*1) of Fig. c is described as follows:

5. After programming is finished, the checksum on the VFD (Fig. f).

At this time, no button is available.

6. Unplug the AC cord from the AC outlet. Then plug it again.

7. Turn the power on by pressing the [POWER ON] button and the tray will close.

8. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. g appears on the screen.

F/W VERSION UP MODE Model No : ******* VERSION : *.***

Please insert a DISCfor F/W Version Up.

"*******" differs depending on the models.

Fig. a Version Up Mode Screen

Fig. b VFD in Version Up Mode

F/W VERSION UP MODE Model No : ******* VERSION : *.***

1. ALL

"*******" differs depending on the models.

Fig. c Programming Mode Screen (Example)

Now Loading...(*1)VERSION : *.** ************A*.bin

Fig. d VFD in Programming Mode (Example)

No. Appearance State

1 Now Loading... Loading the disc

2 Reading...

Sending files into the memory. After reading, automatically the tray opens.

3 Remove the disc

Reading has finished. Remove the disc and close the tray.

4 See FL displayWriting new version data,the progress will be displayed as shown in Fig. e.

Fig. e VFD in Version Up Mode

Fig. f VFD upon Finishing the Programming Mode (Example)

Fig. g


MODEL : *******Version : *.***Region : * / *


17DVD-2500BTCI

9. Press [STOP] button on the remote control unit. Fig. h appears on the screen and Fig. i appears on the VFD.

10. To exit this mode, press [POWER OFF] button.

Fig. h


MODEL : *******Version : *.***Region : * / *


EEPROM CLEAR : OK

Fig. i

18DVD-2500BTCI

SERVICE MODE

Service Mode

Note: If some test are performed continuously, any error will occur.

1st level 2nd level 3rd level Description

1 Mecha test

1 Tray Aging Aging of tray open/close

2 TOC Read TOC reading

3 Heat Run Tray close -> TT1 playback -> TT10 playback -> Tray open -> Tray close

2 VFD/LED Test1 All On Turning on all VFD

2 All Off Turning off all VFD

3 Error Rate Displaying Error rate, Jitterduring playback

4 LD Test1 LD Power

1 Off Turning off LD

2 BD Turning on BD LD

3 DVD Turning on DVD LD

4 CD Turning on CD LD

2 Operating Time Displaying LD Operation Time (with clear function)

5 Channel Level

1 TEST TONE1

Center/Subwoofer/Front LR

2 Surround LR/Surround Back LR

2 Front Lch

3 Center

4 Front Rch

5 Surround Rch

6 Surround Back Rch

7 Surround Back Lch

8 Surround Lch

9 Sub woofer

6 RS-232C1 Parity Setting

1 Even Setting even parity

2 Non Setting non parity

2 Version Up Mode Realta Version up with connecting RS-232C

7 SD Card Test

8 Default Setting Default setting

19DVD-2500BTCI

Entering Service Mode

In power on condition, no discs and tray close, it will be entered into service mode by the following operation using the remote controller. However, it will not be entered when Media Select Item is SD Memory.

Service Mode by using remote controller

Press the following buttons on the remote controller in power on condition, no discs and tray close;

[2]->[5]->[8]->[0]->[CLEAR]

Release from Service Mode

Press the [POWER OFF] button to turn off power.

Screen saver/Auto Power Off in Service Mode

These functions are not performed in Service Mode.

After entering, Fig. j appears on the screen and Fig. k appears on the VFD.

Available button in service mode

Note:Press the number key to select items. Or, press the cursor button (up/down) to select items and press [ENTER] button.

Button condition

ENTER Enter the next level

POWER Turn the power off (when the service mode is completed)

1~8 Enter the selected item (next level)

OTHER Not available

INDICATION DESCRIPTION REMARK

Model Name Model Name E5E***D, etc.

Region BD region - DVD region A-1, etc.

Rel. Ver. Release version

Service Mode

1. Mecha Test2. VFD/LED Test3: Error Rate4: LD Test5: RS-232C6: Channel Level7: SD Card Test8: Default Setting

Model: :E5E**UD Region :A-1Release Ver. :*.*** ADSP1/2 Ver.: ----/---- PLD Ver. :-FPGA Ver.:-- I/P Scaler Ver.:-----

Fig. j Service Mode (Main menu)

* Firmware Version differs depending on the models, and this indication is one example.

Fig. k Service Mode

20DVD-2500BTCI

TRAY LOCK MODE

Tray Lock Mode prevents the tray opening or closing to prevent disc theft in demo mode.

Enter this mode using the following procedure.

1. Confirm that the TV Monitor is connected.

2. With playback stopped, press [SETUP], [TOP MENU], [3], [AUDIO], [0] and [SETUP] buttons on the remote control unit in that order. "Trade On" will appear in the upper right corner on the screen, and on VFD for 2 seconds.

3. To exit this mode, press [SETUP], [TOP MENU], [3], [AUDIO], [0] and [SETUP] buttons on the remote control unit in that order. "Trade Off" will appear in the upper right corner on the screen, and on VFD for 2 seconds.

Fig.a VFD

Fig.b VFD

21DVD-2500BTCI

REMOTE LOCK MODE

SETTING MENU:

Remote Lock Off Mode:

This mode receives an input signal from the remote control unit or from the Remote In-Jack on the rear panel.

Remote Lock On Mode:

This mode dose not receive an input signal from the remote control unit or from the Remote In-Jack on the rear panel.

Perform the setting using the following procedure.

1. Press [ON/STANDBY] and [STOP] buttons on thefront panel simultaneously for over 3 seconds to set"Remote Lock Mode" and display mode.

2. Press [STILL/PAUSE] button on the remote control unit to set to "On" or "Off". When "Remote Lock On", "Remote Lock On" will appear in the upper right corner on the screen and appears on the VFD.

When "Remote Lock Off", "Remote Lock Off" will appear in the upper right corner on the screen and appears on the VFD.

a. If [STILL/PAUSE] button is not pressed for 5 seconds or any other button is pressed within 5 seconds, the unit will be released from "Remote Lock Mode".

b. When initializing, set the Remote Lock Mode "off".

Fig.a VFD

Fig.b VFD

22DVD-2500BTCI

TROUBLESHOOTING

FLOW CHART NO.2The fuse blows out.

After servicing, replace the fuse.

Check the presence that the primary componentis leaking or shorted and service it if defective.

Check the presence that the rectifying diode orcircuit is shorted in each rectifying circuit of secondary side, and service it if defective.

FLOW CHART NO.3When the output voltage fluctuates.

Yes

No

FLOW CHART NO.4When buzz sound can be heard in the vicinity of power circuit.

Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side, and service it if defective. (D1010, D1011, D1016, D1018, D1023, IC2600, IC2601, Q2606, Q2608, Q2609, Q2610, Q2611)

Does the photo coupler circuit on the secondary side operate normally?

Check IC1001, IC1003, D1006 and their periphery, and service it if defective.

Check IC1003, D1009 and their periphery,and service it if defective.

FLOW CHART NO.5-FL is not outputted.

Is -30V voltage supplied to the emitter of Q2503?Check D1018, C1021 and periphery circuit, and service it if defective.

Check Q2503 and their periphery, and service it if defective.

Check FL-SW line and service it if defective.

Is the "L" signal outputted to the collector of Q2507?

Yes

Yes

Yes

Yes No

No

No

No

No

FLOW CHART NO.1

The power cannot be turned on.

Is the fuse normal?

Is normal state restored when once unplugged power cord is plugged again after several seconds?

Is the AL+5V line voltage normal?

See FLOW CHART No.2 <The fuse blows out.>

Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (IC1001, Q1003, T1001, D1001, D1002, D1003, D1004, D1007, D1008, C1010, R1013)

Check each rectifying circuit of the secondary circuitand service it if defective.

Yes

Yes

Yes

No

No

No

Is 3.3V voltage supplied to the emitter of Q2504?

YesIs 3.3V voltage outputted to collector of Q2504?

Is the "H" signal inputted to the base of Q2507?

Replace Q2507.

Replace Q2504.

Check EV+3.3V line and service it if defective.

23DVD-2500BTCI

FLOW CHART NO.6

P-ON+5V (1) is not outputted.

Is 5V voltage inputted to the emitter of Q2610?

Replace Q2611.

Yes

No

Is 11V voltage inputted to the base of Q2611? Is 13.5V voltage inputted to the base of Q2605?

Check D1020, D1023, C1018, C1024, L1003 andtheir periphery, and service it if defective.

No

FLOW CHART NO.7

FLOW CHART NO.8P-ON+10.5V is not outputted.

Is 13.5V voltage inputted to the collector of Q2611?

Yes Yes No

Yes

Check D1016, C1020 and their periphery circuit, and service it if defective.

Check Q2605, D2601, and their periphery, and service it if defective.

Check Q2604, andPWSW3 line, and service it if defective.

Is 2.5V voltage supplied to Pin(1) of IC2601?Yes

No


Replace IC2601.

Is the voltage of base on Q2610 lower than thevoltage of emitter on Q2610 when turning the power on?

Replace Q2610.

Check Q2607 and PWSW3 line and service it if defective.

Yes

No

Check D1013, D1014, D1015, D1021, C1019, C1025, and their periphery, and service it if defective.

Is 5V voltage inputted to the emitter of Q2606?Yes

No

Is the voltage of base on Q2606 lower than thevoltage of emitter on Q2606 when turning the power on?

Replace Q2606.

Check Q2607 and PWSW3 line and service it if defective.

Yes

No

No

Check D1013, D1014, D1015, D1021, C1019, C1025, and their periphery, and service it if defective.

P-ON+5V (2) is not outputted.


Is 5V voltage supplied to Pin(1) of IC2600?

Replace IC2600.

Check D1013, D1014, D1015, D1021, C1019, C1025 and their periphery circuit, and service it if defective.Yes

No

24DVD-2500BTCI

YesNo

FLOW CHART NO.12The key operation is not functioning.

Are the contact point and the installation state of the key switches (SW3000-3003, SW3006-SW3010, SW3100) normal?

When pressing each switches (SW3000-3003, SW3006-SW3010, SW3100), do the voltage of Pin(3,4) of IC2000 increase?

Check the switches (SW3000-3003, SW3006-SW3010,SW3100) and their periphery, and service it if detective.

Check the line between the RS3000 (remote control receiver) and the Pin(27) of IC2000, and service it if detective.

No Re-install the switches (SW3000-3003,SW3006-SW3010, SW3100) correctly or replace the poor switch.

Replace IC2000.Yes

FLOW CHART NO.13No operation is possible from the remote control unit.(Operation is possible from the unit.)

Replace the RS3000 (remote control receiver) or remote control unit.

Is the "L" pulse sent out Pin(1) of RS3000 (remote control receiver) when the remote control unit is activated?

Is the "H" pulse inputted to the Pin(27) of IC2000?

Replace IC2000.

Is 5V voltage supplied to Pin(1) of RS3000 (remote control receiver) ?

YesNo

Check EV+5V line and service it if defective.No

No

Yes

Yes

Yes

Yes

Yes

Yes

No

No

No

No

FLOW CHART NO.11The fluorescent display tube does not light up.

Is 3.3V voltage supplied to Pin(64) of IC3001?

Is the voltage of approximately -30V supplied to Pin(56) of IC3001?

Is there 1.8MHz oscillation at Pin(58) of IC3001?

Are the filament voltage supplied between Pin(1) and Pin(62) of the fluorescent display tube? And the negative voltage applied between these pins and GND?

Replace the fluorescent display tube.

Check the P-ON+3.3V line and service it if defective.

Check the -FL line and service it if defective.

Check R3006, C3003, IC3001 and their periphery, and service it if defective.

Check FL-SW line, and service it if defective.

Is the "H" signal inputted to the base of Q2507?

Check D1010, D1017, T1001, and their periphery, and service it if defective.

Is -20V voltage supplied to collector of Q2502?

No

Yes

YesNo

Check Q2502, Q2508 and their periphery, and service it if defective.

25DVD-2500BTCI

Yes

FLOW CHART NO.15The disc tray cannot be opened and closed.[No Disc] indicated. Picture does not appear normally.Audio is not outputted normally.

Replace the BE Main CBA Unit.

Original BE Main CBA Unit is poor.

Replace the FE Main CBA & BD Mechanism Assembly.

No improvement can be found.No

Yes

FLOW CHART NO.14The disc tray cannot be opened and closed. (It can be done using the remote control unit.)

Is the normal control voltage inputted to Pin(3) of IC2000? Refer to "FLOW CHART NO.12" <The key operation is not functioning.>

Refer to "FLOW CHART NO.15" <The disc tray cannot be opened and closed.>

Replace the "OPEN/CLOSE" switch (SW3006).No

26DVD-2500BTCI

BD Mechanism Replacement GuidelinesThe guidelines describe how to determine whether a BD Mechanism Assembly is defective or not. Confirm that the malfunction is eliminated after replacing the defective BD Mechanism Assembly with a new one.

*The BD Mechanism Assembly shall be acceptable when the following test disc can be played successfully;

*Select [4: LD Test] and select [2: Operating Time] in Service Mode. If the Operating Time shows 3,000 hours or more, the BD Mechanism Assembly shall be determined that it hasreached the end of its life.

BD-ROM BLX-201S3(SONY) chp12

BD-R SBD-8284(ALMEDIO)

FE Main CBA & BD Mechanism Assembly

Replacement of FE Main CBA & BD Mechanism Assembly 1. Remove the Top Cover, Top Panel, Tray Panel and BE Main CBA Unit.2. Disconnect Connectors and replace the FE Main CBA & BD Mechanism Assembly. Refer to CABINET DISASSEMBLY INSTRUCTIONS.

27DVD-2500BTCI

BLOCK DIAGRAMSSystem Control Block Diagram

IC20

00

IC69

05 (

EE

PR

OM

)

IC60

01

SU

BM

ICR

O C

ON

TR

OLL

ER

(MA

IN M

ICR

O C

ON

TR

OLL

ER

)

4

6362

6160

SW

3100

D31

01

PO

WE

R

CN

3101

CN

2001

CN

3000

IC30

01F

L300

0

VF

D

(VF

D D

RIV

ER

)

SDASCLCSRESET

CN

3001 3

3P

OW

ER

-KE

Y5

15K

EY-

14

16K

EY-

2

614

RE

MO

TE

713

FL-

RE

SE

T8

12F

L-C

S9

11F

L-S

CL

1010

FL-

SD

A

XR

ST

XT

RS

T

CN

2503

CN

2304

CN

7001

CN

2000

159

SU

B-T

XD

1411

SY

S-R

ES

ET

1312

RD

Y

166

SU

B-R

XD

218

LED

-R1

19LE

D-G

55

LED

-R6

6LE

D-G

CN

2551

CN

2504 1

1R

EM

OT

E

55

R1-

OU

T4

4T

1-IN

PO

WE

R S

W C

BA

FR

ON

T C

BA

BE

MA

IN C

BA

UN

ITS

UB

MIC

RO

CO

NT

RO

LL

ER

CB

A

RS

232C

CB

AA

V C

BA

AV

CB

A

RS

3000

RE

MO

TE

SE

NS

OR

KE

Y S

WIT

CH

KE

Y S

WIT

CH

27203433

44

55

43M

3

Q20

04B

UF

FE

R

LED

DR

IVE

14 8 9

RE

SE

T

48S

UB

-TX

D49

L3 A16

SU

B-R

XD

LED

-R

SY

S-R

ES

ET

RD

YR

DY

B18

TX

D1

G18

A18

A17

RX

D1

SC

LS

DA

SC

LS

DA

FL-

SD

AF

L-S

CL

FL-

CS

RE

MO

TE

KE

Y-1

3K

EY-

2

OS

C2

OS

C1

8MH

zX

'TA

L

X20

00

EV

+3.

3V

IC20

01

RE

SE

T

D+

3.3V

D+

3.3V

Q20

00

54LE

D D

RIV

ELE

D-G

Q20

01

Q67

02

Q67

03

Q67

01

1025

RS

232C

-RX

D9

26R

S23

2C-T

XD

1421

RE

MO

TE

19R

S23

2C-R

XD

18R

S23

2C-T

XD

1520

PW

SW

217

18P

WS

W3

1322

FL-

SW

305

FAN

-LO

CK

29P

WS

W2

37P

WS

W3

PW

SW

2C

N20

00

CN

2000

CN

2503

CN

2503

PW

SW

3

26F

L-S

WF

L-S

W

62FA

N-L

OC

KFA

N-L

OC

K

TO P

OW

ER

S

UP

PLY

B

LOC

KD

IAG

RA

M

Q67

04

5 6

STA

ND

BY

PO

WE

R

13 15 16 14

23 26 29 24

RE

SE

T

IC67

02

1

D+

3.3V

D+

3.3V

RE

SE

T

IC67

01

21

3

IC25

00

RE

MO

TE

-IN

RE

MO

TE

-OU

T

RS

232C

I/F13 14

CN

2550

RS

232C

-C

ON

NE

CTO

R

3R

XD

2T

XD

1112

IC25

01(A

MP

)

JK25

50

AM

P1

7

RS

232C

INT

ER

FAC

E

Eith

er IC

6701

or

IC67

02 is

use

d fo

r B

E M

AIN

CB

A U

NIT

.

28DVD-2500BTCI

Digital Signal Process 1 Block Diagram

BD

ME

CH

AN

ISM

FE

MA

IN C

BA

W1

V2

U3

HU

(+)

5H

U(-

)6

HV

(+)

7H

V(-

)8

HW

(+)

9H

W(-

)10C

N90

3

IC00

1(M

AIN

MIC

RO

CO

NT

RO

LLE

R/F

E D

IGIT

AL

SIG

NA

L P

RO

CE

SS

)

IC90

2(A

CT

UAT

OR

DR

IVE

)IC

301

(OP

AM

P)

FO

CU

SA

CT

UAT

OR

DR

IVE

OE

IC(C

D/D

VD

)

IC90

3(M

OTO

R D

RIV

E)

IC90

4IC

301

(OP

AM

P)

(MO

TOR

DR

IVE

)

16M

BIT

NO

RF

LAS

HR

OM

DQ

(0-1

5)

RO

MA

(1-2

0)

DQ

(0-1

5)

A(0

-11)

IC40

2(N

OR

FLA

SH

)

IC00

2(R

F A

MP

)

TO D

IGIT

AL

SIG

NA

L P

RO

CE

SS

2B

LOC

K D

IAG

RA

M(C

N64

01)

SC

KS

IS

CK

_0S

O_0

CN

501

3-18

AG

22-A

G24

,A

H20

-AH

24,

AJ2

0-A

J22,

AK

20-A

K24

21,2

2,24

,25

,27,

29

AH12

-AH1

8,AG

15-A

G19

2-13

,42

-53

1-9,

16-2

5,48

29-3

6,38

-4522-2

6,29

-35

N27,

N28,

N30,

P27-

P30,

R27-

R30,

T27-

T30,

U27,

U29,

U30,

V27,

W27

H28-

H30,

J28-

J30,

K27-

K30,

L27,

L28,

L30,

M27

,M28

,M30

IDE

1D(0

-15)

37,3

8,40

,42

,45,

47

A5-A

7,B5

-B7

C5-C

7,D5

-D7

64M

BIT

SD

RA

M

IC40

1(S

DR

AM

)

IC40

3(E

EP

RO

M)

AJ11

-AJ1

5,AJ

18,A

J19,

AK10

-AK1

3,AK

15-A

K19

ATA

PI

I/F

ME

MO

RY

I/F

FE

DIG

ITA

LS

IGN

AL

PR

OC

ES

S

MAT

RIX

RF

EQ

6 5AG

28

AH4

AG5

U4U3R3T1 R4T2AA1

Y3K410

0

125-

128

AH29

/CE

E2C

S1

AH28

SO

SI_

02

AH30

2 4 7 9 10 11 12 13 14

SLD

2(+

)4

SLD

2(-)

3S

LD1(

+)

2S

LD1(

-)1C

N90

2

LOA

D(+

)5

LOA

D(-

)6

LDS

NS

12

LDS

NS

21C

N90

1

FC

S(+

)2

FC

S(-

)3

TR

K(+

)1

TR

K(-

)4

EX

PA(+

)6

EX

PA(-

)7

EX

PB

(+)

8E

XP

B(-

)9

A-D

20-2

3E

-H25

-28

X29

RF

(+)

16R

F(-

)17

BD

RF

(+)

13B

DR

F(-

)14

SD

ATA

40S

CLK

SD

ATA

SC

LK

SD

ATA

SC

LK

38 CN

101

CN

101

15 16 17 1814 13 12 1114 13 15 16

LOA

DIN

GM

OTO

R D

RIV

E10 9

CO

LLIM

ATE

LEN

SM

OTO

R D

RIV

E

SLE

DM

OTO

R D

RIV

E

SP

IND

LEM

OTO

R

DR

IVE

TR

AC

KIN

GA

CT

UAT

OR

DR

IVE

FO

CU

S2-

CO

NT

RO

L

AD

R(0

-5)

AD

W(0

-5)

SW

RF

FO

CU

S1-

CO

NT

RO

L

TR

AC

KIN

G2-

CO

NT

RO

LT

RA

CK

ING

1-C

ON

TR

OL

SLE

D1-

CO

NT

RO

LS

LED

2-C

ON

TR

OL

LOA

D1-

CO

NT

RO

L

LDS

NS

1LD

SN

S2

SP

IND

LE-C

ON

TR

OL

SP

IND

LE-F

G

LOA

D2-

CO

NT

RO

LLO

AD

-CO

NT

RO

L

EX

PA-C

ON

TR

OL

EX

PB

-CO

NT

RO

L

1 26 5 6

U2U123 26 1 2

V4 AG10

AK5

3

V122

1413

W1

19

115-

118

114

141

140

143

142

75 74

J2K210

210

3S

EP

I

K1J310

410

5T

EC

E

H310

6F

E

C2C189

RF

AD

C

WO

B A

DC

WO

B F

E

7 1

5 36 2

OE

IC(B

D)

LDD

SLE

DM

OTO

R

SP

IND

LEM

OTO

R

LOA

DIN

GM

OTO

R

VID

EO

SIG

NA

L

A

UD

IO S

IGN

AL

29DVD-2500BTCI

Digital Signal Process 2 Block Diagram

SD

CB

AB

E M

AIN

CB

A U

NIT

ST

RE

AM

CO

NT

RO

L

ATA

PI I

/F

ED (0

-7)

ED (0

-15)

ED (0

-15)

EA (1

-22)

C0DQ

(0-3

1)

PC0A

(0-1

2)

C1DQ

(0-3

1)

PC1A

(0-1

2)

ME

DIA

PR

OC

ES

SO

R

Java

(B

D-J

)

MP

EG

-2D

EC

OD

ER

HD

(T

S)

SD

(P

S)

CO

PY

PR

OT

EC

TA

AC

S/B

D+

SD

CA

RD

SLO

T

TO D

IGIT

AL

SIG

NA

L P

RO

CE

SS

1B

LOC

K D

IAG

RA

M(C

N50

1)

CN

4001

CN

7602

CN

6401

CN

4002

ME

MO

RY

I/F

SD

I/F

IC60

01(B

E D

IGIT

AL

SIG

NA

L P

RO

CE

SS

)

IC67

04(C

LOC

K G

EN

E.)

F25

G25

B26

C14

C13

B14

IC69

01(N

AN

D F

LAS

H M

EM

OR

Y)

NA

ND

FLA

SH

M

EM

OR

Y (

64M

bit)

IC69

02(N

OR

FLA

SH

ME

MO

RY

)

(DD

R S

DR

AM

)

NO

R F

LAS

H

ME

MO

RY

(8M

bit)

IC65

01,IC

6502

,IC65

03,IC

6504

DD

R S

DR

AM

(512

Mbi

t x 4

)

3-18

IDE

1D(0

-15)

1313

SD

DAT

015

15S

DD

AT1

11

SD

DAT

23

3S

DD

AT3

1111

SD

CLK

77

SD

CD

(DD

R S

DR

AM

)IC

6507

,IC65

08,IC

6509

,IC65

10

DD

R S

DR

AM

(512

Mbi

t x 4

)

D33

,D34

,E32

-E34

,F3

2-F3

4,G

30,G

32,

H29

,H30

,H32

,J2

8-J3

0

A8,A

9,A1

1,B8

,B10

,B11

,C1

1,E1

2,E1

3,F1

4,G

13,G

14

A10,

A12,

A13,

B9,B

12,B

13,

C10,

C12,

E14,

F13,

F15,

G15

A27

,B27

,F2

6,G

26

GR

AP

HIC

S/O

SD

PIX

EL

DAT

A I/

F

CLK V

SH

S

1616

SD

WP

SD

CLO

CK

SD

DAT

A(0

-3)

SD

CA

RD

DE

TE

CT

SD

WR

ITE

PR

OT

EC

T

TO H

DM

IB

LOC

K D

IAG

RA

M

PR

MC

LKP

RM

VS

PR

MH

S

PR

MC

(0-1

1)

PR

MY

(0-1

1) SC

L

33M

CLO

CK

33M

CLO

CK

74M

CLO

CK

27M

CLO

CK

768K

CLO

CK

SC

L

SD

A

HD

MI-

DAT

A0

HD

MI-

DAT

A1

HD

MI-

DAT

A2

HD

MI-

DAT

A3

HD

MI-

MC

KH

DM

I-B

CK

HD

MI-

LRC

KH

DM

I-S

PD

IF

X67

01

27M

Hz

OS

C

CLO

CK

GE

NE

.

SD

A

VID

EO

SIG

NA

L

A

UD

IO S

IGN

AL

SC

LB

16S

DA

C16

TO H

DM

I B

LOC

K D

IAG

RA

M

E11

AP

2

F11

D10 A6

C7

G11 B6

A5

2 3 1 16

7 8 9 10

F28

A31

B30

A28

30DVD-2500BTCI

HDMI Block Diagram

BE

MA

IN C

BA

UN

IT

HD

MI-D

ATA

0H

DM

I-DAT

A1

HD

MI-D

ATA

2H

DM

I-DAT

A3

HD

MI-M

CK

HD

MI-B

CK

HD

MI-L

RC

KH

DM

I-SP

DIF

70-7

3,75

-78,

92,9

4,10

2,10

3

50,5

1,53

-57,

59,

87,8

8,90

,91

TO D

IGIT

AL

SIG

NA

LP

RO

CE

SS

2B

LOC

K D

IAG

RA

M

SC

LS

DA

PR

MC

LKP

RM

VS

PR

MH

S

PR

MC

(0-1

1)

PR

MY

(0-1

1)T.

M.D

.S D

ATA

2-

T.M

.D.S

DAT

A2+

T.M

.D.S

DAT

A1-

T.M

.D.S

DAT

A1+

T.M

.D.S

DAT

A0-

T.M

.D.S

DAT

A0+

T.M

.D.S

CLO

CK

+

T.M

.D.S

CLO

CK

-

JK75

01H

DM

I-C

ON

NE

CT

OR

DD

C D

ATA

DD

C C

LOC

K

HO

T P

LUG

D

ET

EC

T

IC75

01(H

DM

I IN

TE

RF

AC

E)

6 4 9 7 10 123 11519 16

IC75

02

Q75

05,Q

7506

3.3V

<-->

5VC

ON

VE

RTE

R 6 5

2 3

46 45 44 42 41 39 36 35

DR

IVE

23 25 19 21 15 17 13 11

113

116

118

120

119

VID

EO

SIG

NA

L

A

UD

IO S

IGN

AL

121

83 84

CLK

VS

HS

RE

GIS

TER

IIC I/FD

DC

I/F

AUTH

EN

T/C

ATI

ON

KE

YE

XC

HA

NG

E

AU

DIO

I/F

HD

CP

CIP

HE

R/

EN

CR

YP

TO

R

TM

DS

EN

CO

DE

RA

VC

ON

TR

OLL

ER

TM

DS

SE

RIA

LIZ

ER

VID

EO

I/F

31DVD-2500BTCI

Power Supply Block Diagram

IC10

01( S

WIT

CHIN

G C

ONT

ROL)

HO

TC

OL

D

Q26

03

Q26

06

Q26

10

Q26

09

Q26

11

Q26

05

Q26

04

D10

09

Q26

07

Q10

03

VD

D

PO

WE

R S

UP

PL

Y C

BA

2 4 7 6T10

01

11 12 15 13 10 9 16 14

A

V

AC

CO

RD

CN

1003

AC

INLE

TF

1001

2A 2

50V

LIN

EF

ILT

ER

L100

1

F

34IC10

03E

RR

OR

VO

LTA

GE

DE

T

1 2

SH

UN

TR

EG

.

IC26

01

IC26

00

D10

01 -

D10

04

BR

IDG

ER

EC

TIF

IER

SW

ITC

HIN

GC

ON

TR

OL

5

2

3A

L+15

V(1

)14

-16

AL+

15V

(2)

17-1

9A

L+5V

20A

L+2.

5V23

F1

21F

222

-FL

12E

V+

3.3V

314

-16

17-1

920 23 21 2212

CN

10012-

5A

L+5V

CN

1002

CN

2501

FAN

-VC

C1 2

FAN

-LO

CK

CN

2500

1-3

P-O

N+

10.5

V7,

8P

-ON

+5V

(1)

CN

2601

CN

2304

CN

250314-1

5P

-ON

+3.

3V11

P-O

N+

1.2V

SW

+15

V

TO F

E M

AIN

CB

A(C

N00

1)

TO B

E M

AIN

CB

A U

NIT

(CN

7001

)

TO

SU

B M

ICR

O-

CO

NT

RO

LLE

R

CB

A(C

N20

00)

TO B

E M

AIN

CB

A U

NIT

(CN

7401

)

TO S

YS

TE

M

CO

NT

RO

LB

LOC

KD

IAG

RA

M

FAN

-LO

CK

PW

SW

3P

WS

W2

FL-

SW

SW

+10

.5V

SW

+5V

SW

+5V

+3.

3VR

EG

.

+1.

2VR

EG

.

6

1 3

HO

T C

IRC

UIT

. BE

CA

RE

FU

L.

FA

N

Q26

08

+3.

3V R

EG

.

AV

CB

A

Q25

02

Q25

08Q

2504

Q25

03

Q25

0717P

-ON

+5V

(2)

28P

-ON

+3.

3V8

EV

+3.

3V

27E

V+

5V

23F

133

F2

29-F

L

CA

UT

ION

!F

ixed

vol

tage

(or

Aut

o vo

ltage

sel

ecta

ble)

pow

er s

uppl

y ci

rcui

t is

used

in th

is u

nit.

If M

ain

Fus

e (F

1001

) is

blo

wn

, che

ck to

see

that

all

com

pone

nts

in th

e po

wer

sup

ply

circ

uit a

re n

ot d

efec

tive

befo

re y

ou c

onne

ct th

e A

C p

lug

to th

e A

C p

ower

sup

ply.

Oth

erw

ise

it m

ay c

ause

som

e co

mpo

nent

s in

the

pow

er s

uppl

y ci

rcui

t to

fail.

NO

TE

:T

he v

olta

ge fo

r pa

rts

in h

ot c

ircui

t is

mea

sure

d us

ing

hot G

ND

as

a co

mm

on te

rmin

al.

"Ce

sym

bole

rep

rèse

nte

un fu

sibl

e à

fusi

on r

apid

e."

CA

UT

ION

!F

or c

ontin

ued

prot

ectio

n ag

ains

t fire

haz

ard,

repl

ace

only

with

the

sam

e ty

pe fu

se.

AT

TE

NT

ION

: P

our

une

prot

ectio

n co

ntin

ue le

s ris

qes

d'In

cele

n'u

tilis

er q

ue d

es fu

sibl

e de

mêm

e ty

pe.

Ris

k o

f fi

re-r

epla

ce fu

se a

s m

arke

d."T

his

sym

bol m

eans

fast

ope

ratin

g fu

se."

A

V

F

32DVD-2500BTCI

SCHEMATIC DIAGRAMS AND TEST POINTS

Standard Notes

WARNING

Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.

Notes:1. Do not use the part number shown on these

drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.

2. All resistance values are indicated in ohms (K = 103, M = 106).

3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.

4. All capacitance values are indicated in μF(P = 10-6 μF).

5. All voltages are DC voltages unless otherwise specified.

33DVD-2500BTCI

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:

1. CAUTION:

FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED.

2. CAUTION:

Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the

parts list, and may be slightly different or amended since the drawings were prepared.

2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.

4. Voltage indications for PLAY and STOP mode on the schematics are as shown below:

5. How to read converged lines

6. Test Point Information

A V

F

This symbol means fast operating fuse.Ce symbole represente un fusible a fusion rapide.

2 31 5.0(2.5)

5.0

The same voltage for both PLAY & STOP modes

Indicates that the voltage is not consistent here.

PLAY modeSTOP mode

(Unit: Volt)

3

2

1

A B C D

1-B1

1-D3

AREA D3

AREA B1

1-D3

Distinction AreaLine Number (1 to 3 digits)

Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".

: Indicates a test point with a jumper wire across a hole in the PCB.

: Used to indicate a test point with a component lead on foil side.

: Used to indicate a test point with no test pin.

: Used to indicate a test point with a test pin.

34DVD-2500BTCI

AV Schematic Diagram

35DVD-2500BTCI

Sub Microcontroller Schematic Diagram

36DVD-2500BTCI

Power Supply Schematic DiagramCAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1001) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.

NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.

"Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !For continued protection against fire hazard,replace only with the same type fuse.ATTENTION : Pour une protection continue les risqesd'Incele n'utiliser que des fusible de même type.Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."

A V

F

37DVD-2500BTCI

Front & Power SW Schematic Diagram

DIGITALMULTI2 CH DTS+DTS

MP3HDCDxMPEGPCML. P. D.MIX

ANGLEWMA AAC

MSTR-HDExpress

TrueHDV S SPL

REMSINGTOTALCHAPTRACKTITLEGROUPHDMISUPER1G 2G

(h1) (h1) (h1) (h1) (h1) (h1) (h1) (h1) (h1) (h1)

(h1) (h1)

3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G 15G

HDBD

PROG RANDB1 A-

SD USB NETDVD VCD

AUDIO

1G 2G~14G 15G

P1

P2

P3

P4

P5

P6

P7

P8

P9

FL3000 MATRIX CHART

P10

P11

P12

P13

P14

P15

P16

P17

P18

P19

P20

P21

P22

P23

P24

P25

P26

P27

P28

P29

P30

P31

P32

P33

P34

P35

P36

SUPER

HD

BD

PROGRAND

B

1A-

SDUSBNET

DVDV

CD

AUDIODIGITAL

DTS+

DTS

MP3

HDCDx

MPEGPCM

L.P.

D.MIX

ANGLE

WMAAAC

MSTR-HD

ExpressTrueHD

V SS

PL

a1

a2

a3

a4

a5

b1

b2

b3

b4

b5

c1

c2

c3

c4

c5

d1

d2

d3

d4

d5

e1

e2

e3

e4

e5

f1

f2

f3

f4

f5

g1

g2

g3

g4

g5

h1

a1

b1

c1

d1

e1

g1

f1

a2

b2

c2

d2

e2

f2

g2

a3

b3

c3

d3

e3

f3

g3

a4

b4

d4

e4

g4

a5

b5

c5

d5

e5

f5

g5

(2G~14G)

c4

f4

38DVD-2500BTCI

SD Schematic DiagramRS232C Schematic Diagram

39DVD-2500BTCI

FE Main 1/5 Schematic DiagramThe order of pins shown in this diagram is different from that of actual IC001.IC001 is divided into four and shown as IC001 (1/4) ~ IC001 (4/4) in this FE Main Schematic Diagram Section.

1 NOTE:

40DVD-2500BTCI


1 NOTE:

41DVD-2500BTCI

FE Main 3/5 Schematic Diagram

42DVD-2500BTCI


1 NOTE:

43DVD-2500BTCI

FE Main 5/5 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC001.IC001 is divided into four and shown as IC001 (1/4) ~ IC001 (4/4) in this FE Main Schematic Diagram Section.

1 NOTE:

44DVD-2500BTCI

BE Main 1/9 Schematic Diagram

The order of pins shown in this diagram is different from that of actual IC6001.IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section.

2 NOTE:

45DVD-2500BTCI

BE Main 2/9 Schematic DiagramThe order of pins shown in this diagram is different from that of actual IC6001.IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section.

2 NOTE:

46DVD-2500BTCI



2 NOTE:

47DVD-2500BTCI


2 NOTE:

48DVD-2500BTCI


2 NOTE:

49DVD-2500BTCI



2 NOTE:

50DVD-2500BTCI


2 NOTE:

51DVD-2500BTCI



2 NOTE:

52DVD-2500BTCI


53DVD-2500BTCI

WIRING DIAGRAM

AV

CB

AS

UB

MIC

RO

CO

NT

RO

LL

ER

CB

A

FR

ON

T C

BA

PO

WE

R S

UP

PL

Y C

BA

BE

MA

IN C

BA

UN

IT

FE

MA

IN C

BA

SD

CB

A

PO

WE

RS

W C

BA

RS

232C

CB

AC

N30

00

CN

1001

CN

1002

CN

7401

CN

7602

CN

4002

CN

2501

CN

2304

CN

7001

CN

6401

CN

501

CN

101

CN

902

CN

901

CN

903

CN

2601

CN

001CN

3001

CN

3101

CN

2500

W10

CN

2504

CN

2551

CN

2000

CN

2503

CN

2001

AC

CO

RD

HD

MI-

CO

NN

EC

TO

R

RS

232C

-CO

NN

EC

TO

R

SD

CA

RD

SLO

T

28H29XOUT30GND31GND

1SLD1(-)2SLD1(+)3SLD2(-)4SLD2(+)

32+3.3V33GND-LD34GND-LD35+5V36+8.5V37THERMO38SCLK

1W2V3U4+5V5HU(+)6HU(-)7HV(+)8HV(-)9HW(+)

10HW(-)11HB(-)

39SENLDD40SDATA41XLDDRST42LDEN43EMST44TEST-V45NU

1TRK(+)2FCS(+)3FCS(-)4TRK(-)5EXPINT6EXPA(+)7EXPA(-)8EXPB(+)9EXPB(-)

10SENLCD11NU12GND13BDRF(+)14BDRF(-)15GND16RF(+)17RF(-)18GND19+5V20A21B22C

1NSRST2GND3IDE1D74IDE1D85IDE1D66IDE1D97IDE1D58IDE1D109IDE1D4

10IDE1D1111IDE1D312IDE1D1213IDE1D214IDE1D1315IDE1D116IDE1D1417IDE1D018IDE1D1519GND20NU21DMAIRQ22GND23DIOW24GND25DIOR26GND27IORDY28GND29DMACK30GND31INTRQ32NU33IDE1A134NU35IDE1A036IDE1A237CS038CS139NU40

123456789

10111213141516171819202122232425262728293031323334353637383940

1P-ON+10.5V2P-ON+10.5V3P-ON+10.5V4GND5GND6GND7P-ON+5V(1)8P-ON+5V(1)9GND

10GND11P-ON+1.2V12GND13GND14P-ON+3.3V15P-ON+3.3V

123456789

101112131415

11GND12PWSW113RDY14SYS-RESET15SUB-TXD16SUB-RXD17P-ON+5V(2)18NU19NU

111213141516171819

1FAN-VCC2FAN-LOCK

1SDDAT22GND3SDDAT34GND5CMD6GND7SDCD8D+3.3V9D+3.3V

10GND11SDCLK11NU

10GND9GND8GND7GND6GND5AL+5V4AL+5V3AL+5V2AL+5V1SAFETY

12GND13SDDAT014GND15SDDAT116SDWP

123456789

1011NU11

GND10GND9GND8GND7GND6AL+5V5AL+5V4AL+5V3AL+5V2SAFETY1

1213141516

1NU2GND3AL+15V(1)4GND5GND6NU7SAFETY8NU9GND

10GND11GND12EV+3.3V13NU14AL+15V(2)15AL+15V(2)16AL+15V(2)17AL+5V18AL+5V19AL+5V20AL+2.5V21F222-FL23

1234567891011121314151617181920212223 F1

2F23F14GND5GND6EV+3.3V7NU8EV+5V9P-ON+3.3V

10FL-SDA11FL-SCL12FL-CS13FL-RESET14REMOTE15KEY-116KEY-217NU18LED-R

23456789101112131415161718

1-FL1

1REMOTE12EV+5V23RS232C-PW-CONT34T1-IN45R1-OUT56GND6

19LED-G19

3P

OW

ER

-KE

Y

31 2

4G

ND

45

LED

-R5

6LE

D-G

6

GND

23D24OEVC25E26F27G

FA

N

CN

1003

FE

MA

IN C

BA

& B

D M

EC

HA

NIS

M A

SS

EM

BL

Y

RE

LA

Y C

BA

PIC

KU

P

FO

CU

SA

CT

UAT

OR

BD

-OE

IC

TR

AC

KIN

GA

CT

UAT

OR

LEN

S D

RIV

E

CD

/DV

D-O

EIC

CD-LD

BD-LD

PD-LD

DVD-LD

LAS

ER

DIO

DE

DR

IVE

SP

IND

LEM

OT

OR

MS

LED

MO

TO

R

M

11 LDSNS222 LDSNS133 GND44 INLIMIT55 LOAD(+)66 LOAD(-)

MLO

AD

ING

MO

TO

R

TR

AY

-IN

INN

ER

SW

TR

AY

-OU

T

3GND324V5V-PW-SW(NU)315FAN-LOCK306SUB-RXD297SAFETY288EV+3.3V279SUB-TXD26

10FAN-CONT(NU)2511SYS-RESET2412RDY2313GND2214PWSW12115NU2016IIC-BUS SCL(NU)1917IIC-BUS SDA(NU)1818PWSW31719NU1620PWSW21521REMOTE1422FL-SW1323A33-PW-CONT(NU)1224RS232C-PW-CONT1125RS232C-RXD1026RS232C-TXD927EV+5V828P-ON+3.3V729-FL630NU531GND432GND333F2234F11

W05

W07

W06

W04

W08W03

54DVD-2500BTCI

LEAD IDENTIFICATIONS

1 2 3 4

48

17

32

33

161

64

49

G D S

1 2 3

5 4

1 4

8 5

1

2

4

3

1: Anode2: Cathode3: Emitter4: Collector

64 33

321

C

B E

E C BE C B

E C B

1 2 4 5

3

1 8

16 9

B C E

B C E

16 9

81

Note:A: AnodeK: CathodeE: EmitterC: CollectorB: BaseR: ReferenceG: GateD: DrainS: Source

2SA950-Y(TE2 F T)2SA966-Y(TE6 F M)2SA1015-(GR,Y)(TE2 F T)2SA1981Y-AT2SC1815-GR(TE2 F T)2SC2120-Y(TE2 F T)2SC5343MG-AT2SC5344 YKTA1271-Y-AT/P

STB1277LY-AT2SA1980M Y2SA1980MG-ATKRC103M-AT/PKTA1267-(GR,Y)-AT/PKTA1273-Y-AT/PKTC3203-Y-AT/PKTC3199-GR-AT/PRN1203(TE4 F T)SRC1202M-ATSRC1203MATKRC102M-AT/PRN1202

PQ070XF02SZH2SK3563(Q)KHB4D5N60F-U/PMC

BU4229G-TRPST3630NR

EL817BPS2561A-1(Q,W)

CXA1511M-T4FA5542N-A2-TE1PT6302-R-001(L)

2SA1530A-T112-1Z2SA1980SFYKTA1504S-Y-RTK/P

MN101C77AFS

STC403

PQ035ZN01ZPHPQ035ZNA1ZPH

ADM232AARN 2SD2012(F M) KTC2026-Y/P

SP232ACN-L/TR

---MEMO---

55DVD-2500BTCI

EXPLODED VIEWS

Cabinet

2L025

B8

B24

B9B11

B5

B19B18

B1

B17

B41

B16

B17

A3

B4

B34

B27B2

A1X

2L010

2L012

B39

2L062

2L021

2L021

2L0212L023

2L0231B1

2L024 2L018

2L018

2L064

2L064

2L024

2L018

2L018

2L028

2L028

2L040

2L040

2L040

2L040

2L020 2L020

2L029

2L019

2L019 2L029

B15

B31

A6

A6

A6

A5

A2

B3

B30

A6 A7

A7

A7

A7

2L021

2L082

2L062

2L062

2L013B40

2L014

2L014

2L041

2L041

2L027

2L015

2L026

2L060

2L034

2L034

2L022

2L012

2L063

A4

B20

2L081

A21

2L061

2L0702L080

2L081

2L0252L081

FRONT CBA

POWER SW CBA

CN4003

B46

FE MAIN CBA & BD MECHANISM ASSEMBLY

AV CBA

B49

BE MAIN CBA Unit

SUB MICROCONTROLLER CBA

RS232C CBA

SD CBA

W10

W05

FN1001

W04

W03

W07

W06

W08

B47

B48

A8

B44

B38

POWER SUPPLYCBA

Note: Be sure to unplug the power cord from

the power outlet before disassembling.

“Current continues to flow in the set for

10 to 20 seconds after the power cord is

unplugged. Wait until the power LED

turns completely off before proceeding.”

56DVD-2500BTCI

PARTS LIST OF EXPLODED VIEW＊本表に "nsp" と記載されている部品は供給できません。＊ Parts for which "nsp" is indicated on this table cannot be supplied.

＊本表に "nsp" と記載されている基板 ASS’Yは供給できません。基板 ASS’Yの修理の際には基板部品表を確認のうえ、交換部品を発注してください。＊ P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts.

＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.

Ref. No. Part No. Part Name Remark Q'ty New00D9H26000943 BE MAIN CBA UNIT 1VSA16866 1 *

00D9H26000944 AV ASSEMBLY 1VSA16867 1 *- AV CBA- SUB MICROCONTROLLER CBA- RC232C CBA

00D9H26000953 POWER SUPPLY CBA 1VSA16825 1 *

00D9H26000955 FRONT ASSEMBLY 1VSA16851 1 *- FRONT CBA- POWER SW CBA

00D9H26000954 SD CBA 1VSA16864 1 *

A1X 00D9H26000945 FRONT ASSEMBLY E5E01UD 1VM121439 1 *A2 nsp CHASSIS E5E00UD 1VM020691 1 *A3 00D9H26000946 TOP COVER E5E00UD 1VM020690 1 *A4 00D9H26000947 REAR PANEL E5E01UD 1VM223696 1 *A5 nsp BOTTOM PANEL E5E00UD 1VM223212 2 *A6 00D1040334007 FOOT 1VM426219 4A7 00D4611050005 RUBBER PAD 1VM426239 4A8 00D9H26000948 TRAY ASSEMBLY(BLACK) E5E00UD 1VM223619 1 *

A21 nsp LABEL SERIAL NO. E57E0UD - 1 *1B1 00D9H26000942 FE MAIN CBA & BD MECHANISM ASSEMBLY N77D0AUN 1 *

B1 nsp TOP PANEL E5E00UD 1VM223211 1 *B2 nsp FRONT BRAKET E5E00UD 1VM324206 1 *B3 nsp PDESTAL E5E00UD 1VM121240 1 *B4 nsp POWER PCB HOLDER E5E00UD 1VM223219 1 *B5 nsp FAN HOLDER E5E00UD 1VM223222 1 *B8 nsp BE SCALER HOLDER(ENTRY) E5E01UD 1VM121381 1 *B9 nsp BE SCALER SUB HOLDER E5E00UD 1VM121242 1 *

B11 nsp RS232 HOLDER(ENTRY) E5E01UD 1VM324702 1 *B15 nsp SD PCB HOLDER E5E00UD 1VM324231 1 *B16 nsp NEOPRENE SPONGE(250X25X2) E5E00UD 1VM427820 1 *B17 nsp NEOPRENE SPONGE(250X50X1) E5E00UD 1VM427821 1 *B18 nsp NEOPRENE SPONGE(250X25+150X50) E5E00UD 1VM427822 1 *B19 nsp NEOPRENE SPONGE(250X25X1) E5E00UD 1VM427819 1 *B20 nsp LEAD CLAMPER 100MM 1790356 2 *B24 nsp MACHA EARTH PLATE R E9H10UD 1VM425524 1 *B27 nsp NEOPRENE SPONGE(8X120) E5E00UD 1VM427440 1 *B30 nsp BASS RUBBER E5E00UD 1VM427420 1 *B31 nsp SD EARTH PLATE E5E00UD 1VM224376 1 *B39 nsp COATING CLIP S-3 XF01054WD001 1 *B40 nsp TAPE HIMELON(10X150) E5E00UD 1VM427421 1 *B41 nsp INSULATION SHEET(TOP PANEL) E5E00UD 1VM427779 1 *B42 nsp INSULATION SHEET(LOADER) E5E00UD 1VM326057 1 *B43 nsp WIRE ASSEMBLY RING TERMINAL 1PIN 80MM WX1E5E01-012 1 *

57DVD-2500BTCI

SCREWS2L010 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 22L012 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 32L013 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 12L014 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 32L015 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 32L018 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 92L019 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 32L020 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 82L021 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 102L022 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 32L023 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 22L024 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 22L025 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 22L026 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 22L027 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 22L028 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 42L029 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 42L034 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 72L040 nsp SCREW S-TIGHT M3X8 BIND HEAD+ GBJS3080 42L041 nsp SCREW S-TIGHT M3X8 BIND HEAD+ GBJS3080 22L060 nsp P-TIGHT SCREW M3X34 E9400UD 1VM420034A 22L061 nsp HEXAGON SPACER E6AE0UD 1VM424730 22L062 nsp TOP COVER SCREW S-TIGHT SCREW M4X8 1VM425652 92L064 SCREW 22L063 nsp SCREW S-TIGHT M3X8 DISH HEAD+ GDHS3080 22L070 nsp SCREW B-TIGHT M3X8 BIND HEAD+ GBHB3080 12L080 nsp SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050 12L081 nsp SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050 32L082 nsp SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050 2

Ref. No. Part No. Part Name Remark Q'ty New

58DVD-2500BTCI

Packing

Some Ref. Numbers are not in sequence.

X2 X12 X38

Upper SideLower Side

X15

X6

S3

S5

S8

A22

A30

S2

S5

S6

S4

S4

X4

A30

X1

S9

S10

59DVD-2500BTCI

PARTS LIST OF PACKING & ACCESSORIES＊本表に "nsp" と記載されている部品は供給できません。＊ Parts for which "nsp" is indicated on this table cannot be supplied.

＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.

Ref. No. Part No. Part Name Remark Q'ty NewA22 nsp BAR CODE LABEL E5E01UD - 1 *A30 nsp CONTROL LABEL E5E01UD - 1 *S2 00D9H26000949 GIFT BOX CARTON E5E01UD 1VM325357 1 *S3 00D9H26000933 WRAPPING SHEET(MIRROR MAT) E5E00UD 1VM426159 1 *S4 00D9H26000934 TOP SIDE PAD E5E01UD 1VM121561 2 *S5 00D9H26000935 BOTTOM SIDE PAD E5E00UD 1VM121380 2 *S6 00D9H26000936 FRONT PAD E5E00UD 1VM325022 1 *S8 00D9H26000938 REAR PAD E5E01UD 1VM427521 1 *S9 nsp ACCESSORY BOX E5E00UD 1VM325939 1 *

S10 nsp PACKING SHEET 1 *X1 00D9H26000950 REMOTE CONTROL UNIT NA843UD NA843UD 1 *X2 00D9H26000951 OWNERS MANUAL E5E01UD 1VMN24373 1 *X4 00D9H26000513 ACCESSORY BAG E5795ED 0VM416059 1 *X6 nsp DRY BATTERY R6P/2S XB0M451T0001 2 *X6 nsp DRY BATTERY R6UW/2S XB0M311MS001 2 *X6 nsp DRY BATTERY ES-GR6M-C XB0M571GLP01 2 *

X12 nsp SERVICE CENTER SHEET E8700UD 1VM425536 1 *z X15 00D9H26000952 AC CORD W/O A GND WIRE UL/CSA/202/NO/BLACK WAV0202LTE01 1 *

X38 nsp WARRANTY SHEET E6E80UD 1VM323952 1 *

60DVD-2500BTCI

SERVICE MANUAL Brand Company, D&M Holdings lnc. e Ver. 1 SERVICE MANUAL BLU-RAY DISC/DVD VIDEO...

Documents

Transcript of SERVICE MANUAL Brand Company, D&M Holdings lnc. e Ver. 1 SERVICE MANUAL BLU-RAY DISC/DVD VIDEO...