Server Connection- (Fibre Channel) - Fujitsu

7/23/2019 Server Connection- (Fibre Channel) - Fujitsu

1/58

FUJITSU Storage

ETERNUS DXConfiguration Guide -Server Connection-

(Fibre Channel) for WindowsDriver Settings for Fujitsu Fibre Channel Cards

P3AM-6332-11ENZ0


2/58

This page is intentionally left blank.


3/58

Preface

This manual briefly explains the operations that need to be performed by the user in order to connect an

ETERNUS DX Disk storage system or an ETERNUS DX200F All Flash Array to a Fujitsu server running Windows

via a Fibre Channel interface.

This manual is used when performing the setup procedure described in "Installing Drivers and Setting Up theServer" of the "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Win-

dows".

This manual should be used in conjunction with any other applicable user manuals, such as those for theETERNUS DX Disk storage system, ETERNUS DX200F All Flash Array, server, OS, Fibre Channel cards, and driv-ers.

Refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Notations" for the notationsused in this manual such as product trademarks and product names.

This manual references the following documents:

Server Support Matrix FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX60 S3/

DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk Storage Systems, ETERNUS DX200F All Flash ArraySettings

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX80 S2/DX90 S2, ETERNUS DX410 S2/DX440 S2, ETERNUS DX8100 S2/DX8700 S2 Disk Storage System Settings

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX60/DX60S2, DX80, DX90 Disk Storage System Settings

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX400/DX8000 series Disk Storage System Settings

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows

This manual is designed for use with the following storage systems:

ETERNUS DX60 S3/DX100 S3/DX200 S3 Disk storage system

ETERNUS DX500 S3/DX600 S3 Disk storage system

ETERNUS DX60 S2/DX80 S2/DX90 S2 Disk storage system



ETERNUS DX60/DX80/DX90 Disk storage system

ETERNUS DX410/DX440 Disk storage system

ETERNUS DX8100/DX8400/DX8700 Disk storage system

ETERNUS DX200F All Flash Array

11th Edition

December 2014

3FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows

Copyright 2014 FUJITSU LIMITED

P3AM-6332-11ENZ0


4/58

The Contents and Structure of this Manual

This manual is composed of the following three chapters and an appendix.

"Chapter 1 Setup Procedure for PRIMERGY" (page 8)This chapter describes how to install a Fibre Channel card, set up the Fibre Channel card BIOS, install theFibre Channel card driver, check the driver version, and set up the driver parameters for PRIMERGY.

"Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series" (page 30)

This chapter describes how to install a Fibre Channel card, set up the Fibre Channel card BIOS, install theFibre Channel card driver, check the driver version, and set up the driver parameters for PRIMEQUEST 1000series.

"Chapter 3 Setup Procedure for PRIMEQUEST 500/400 Series" (page 39)

This chapter describes how to install a Fibre Channel card, set up the Fibre Channel card BIOS, install theFibre Channel card driver, check the driver version, and set up the driver parameters for PRIMEQUEST500/400 series.

The appendix consists of a management table that is used in the "Setting Up the Fibre Channel Cards" sec-tion, and information on how to set up the server when Fujitsu QLogic Fibre Channel cards (2Gbit/s) are used.

Fibre Channel card names

Refer to "Server Support Matrix" to check the Fibre Channel cards.

"Fujitsu Emulex Fibre Channel cards" refers to Fibre Channel cards with the following product IDs.

- PG-FC105

- PG-FC106

- PG-FC107

- PG-FC201

- PG-FC202/PG-FC202L


- PY-FC201/PY-FC201L



- PY-FC221/PY-FC222

- PG-FCD201

- PG-FCD202

- MC-0JFC31/MCX0JFC31/MC-0JFC3L



- MC-0JFCA1/MCX0JFCA1/MC-0JFCAL

- MC-0JFC71/MCX0JFC71


- MC-0JFC81/MCX0JFC81


- MC-0JFC11/MC-0JFC1L

Preface



P3AM-6332-11ENZ0


5/58

- MC-0JFC21/MC-0JFC2L

- MC-08FC11/MC-08FC71

- MC-08FC31/MC-08FC41

- MC-08FC51/MC-08FC61

- MC-08FC81/MC-08FC91- S26361-F2624-E1

- S26361-F2843-E1/S26361-F2843-E201

- S26361-F3141-E10/S26361-F3141-E210

- S26361-F3141-E1

- S26361-F3306-L1/S26361-F3306-L201

- S26361-F3961-L1/S26361-F3961-L201

- S26361-F3961-L2/S26361-F3961-L202

- S26361-F3306-E601/BX600-FC42E

- MC-FC82E "Fujitsu QLogic Fibre Channel cards" refers to Fibre Channel cards with the following product IDs.

- PG-FCD101

- PG-FCD102





- S26361-F3023-E1

-

S26361-F3631-L1/S26361-F3631-L201- S26361-F3631-L2/S26361-F3631-L202

Preface



P3AM-6332-11ENZ0


6/58

Table of Contents

Chapter 1 Setup Procedure for PRIMERGY 8

1.1 Workflow ........................................................................................................................................ 8

1.2 For Fujitsu Emulex Fibre Channel Cards........................................................................................ 11

1.2.1 Setting Up the Fibre Channel Cards.....................................................................................................................11

1.2.2 Setting Up SAN Boot ...........................................................................................................................................14

1.2.3 Installing Windows .............................................................................................................................................14

1.2.4 Installing the Driver............................................................................................................................................14

1.2.5 Checking the Driver Version................................................................................................................................15

1.2.6 Setting Up the Driver Parameters .......................................................................................................................151.2.7 Setting Fixed Target IDs ......................................................................................................................................20

1.2.8 Installing the ETERNUS DX Driver........................................................................................................................20

1.3 For Fujitsu QLogic Fibre Channel Cards......................................................................................... 20


1.3.2 Setting Up SAN Boot ...........................................................................................................................................23

1.3.3 Installing Windows .............................................................................................................................................25



1.3.6 Setting Up the Driver Parameters .......................................................................................................................25


Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series 30

2.1 Workflow ...................................................................................................................................... 30

2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards.............................................................. 32


2.2.2 Installing the Driver............................................................................................................................................352.2.3 Checking the Driver Version................................................................................................................................35


2.2.5 Setting Fixed Target IDs ......................................................................................................................................37


Chapter 3 Setup Procedure for PRIMEQUEST 500/400 Series 39

3.1 Workflow ...................................................................................................................................... 39

3.2 For Fujitsu Emulex Fibre Channel Cards........................................................................................ 40



P3AM-6332-11ENZ0


7/58






Appendix A WWN Instance Management Table for the Server (Blank) 47

Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s) 48

B.1 Workflow...................................................................................................................................... 48

B.2 Setting Up the Fibre Channel Cards.............................................................................................. 50

B.3 Setting Up SAN Boot..................................................................................................................... 53B.4 Installing Windows....................................................................................................................... 55

B.5 Installing the Driver ..................................................................................................................... 55

B.6 Checking the Driver Version ......................................................................................................... 55

B.7 Installing the ETERNUS DX Driver ................................................................................................. 56

Table of Contents



P3AM-6332-11ENZ0


8/58

Chapter 1Setup Procedure for PRIMERGY

This chapter describes how to install and set up the Fibre Channel cards in PRIMERGY.

1.1 Workflow

Workflow

When using the 2Gbit/s Fujitsu QLogic Fibre Channel cards, refer to "Appendix B For Fujitsu QLogic FibreChannel Cards (2Gbit/s)" (page 48).

Setting Up the Fibre Channel Cards

Install the Fibre Channel cards, acquire their physical addresses, and perform the BIOS settings.

For Fujitsu Emulex Fibre Channel cards

- "1.2.1 Setting Up the Fibre Channel Cards" (page 11)

For Fujitsu QLogic Fibre Channel Cards


Setting Up SAN Boot

Set up the SAN Boot configuration (if SAN Boot is to be used).


- "1.2.2 Setting Up SAN Boot" (page 14)

For Fujitsu QLogic Fibre Channel cards

- "1.3.2 Setting Up SAN Boot" (page 23)



P3AM-6332-11ENZ0


9/58

Installing Windows

Install Windows.


- "1.2.3 Installing Windows" (page 14) For Fujitsu QLogic Fibre Channel Cards

- "1.3.3 Installing Windows" (page 25)

Installing the Driver

Install the Fibre Channel card driver.


- "1.2.4 Installing the Driver" (page 14)

- "1.2.5 Checking the Driver Version" (page 15)



- "1.3.5 Checking the Driver Version" (page 25)

Setting Up the Driver ParametersSet up the parameters for the Fibre Channel card driver.


- "1.2.6 Setting Up the Driver Parameters" (page 15)



Chapter 1 Setup Procedure for PRIMERGY1.1 Workflow



P3AM-6332-11ENZ0


10/58

Installing the ETERNUS DX Driver

Install the ETERNUS DX driver.


- "1.2.8 Installing the ETERNUS DX Driver" (page 20)- Checking the driver-related notes

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Win-

dows"


- "1.3.7 Installing the ETERNUS DX Driver" (page 28)

- Checking the driver-related notes


dows"

After all of the required procedures in this manual are complete, proceed to the procedure that is de-scribed in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for

Windows".

Chapter 1 Setup Procedure for PRIMERGY1.1 Workflow



P3AM-6332-11ENZ0


11/58

1.2 For Fujitsu Emulex Fibre Channel Cards

This section describes how to set up the server for use with the Fujitsu Emulex Fibre Channel cards.

When using the Fujitsu QLogic Fibre Channel cards, follow the procedure in "1.3 For Fujitsu QLogic FibreChannel Cards" (page 20).

Depending on the Fibre Channel card used, the actual on-screen Fibre Channel card information may dif-fer from that in the screenshots shown in this manual.

1.2.1 Setting Up the Fibre Channel Cards

Install the Fibre Channel cards in the server, acquire the relevant physical addresses and World Wide Names

(WWNs), and perform Topology and LinkSpeed settings. The physical address and WWN of a Fibre Channel card are required information in the following cases:

when an error has occurred in the system, when using the ETERNUS DX storage systems (security function,host affinity function, etc.) to restrict server access, or when connecting the ETERNUS DX storage systemsand the server using a Fibre Channel switch.

The relationship between a physical address and WWN cannot be determined from BIOS and OS. The physi-cal address and WWN must be recorded as a pair when each Fibre Channel card is installed. Physical ad-dress and WWN must be assigned to "WWN instance management table for the server".

The workflow is shown below.

(1) Install the Fibre Channel card

(2) Turn on the server

(3) Acquire the physical address and WWN for the Fibre Channel card

(4) Add a record for the server in the WWN instance management table for the server

(5) Set the Topology and LinkSpeedWhen installing two or more Fibre Channel cards in the server, first turn off the server, then repeat Steps (1)through (5) above for each Fibre Channel card to be installed.

The procedure is as follows:

1 Install the Fibre Channel card in the server.

For the installation method, slot positions, and notes regarding the Fibre Channel card, refer to themanual provided with the Fibre Channel card or the user guide of the server.

2 Turn on the server, and press the [Alt] + [E] keys or [Ctrl] + [E] keys while the following message isdisplayed.

!!! Emulex LightPulse x86 BIOS !!!, Version xxxxxx

Copyright (c)1997-2010 Emulex.All rights reserved.

Press or to enter Emulex BIOS configuration

utility. Press to skip Emulex BIOS.

"LightPulse BIOS Utility" starts.

Chapter 1 Setup Procedure for PRIMERGY1.2 For Fujitsu Emulex Fibre Channel Cards



P3AM-6332-11ENZ0


12/58

3 Select the port for the Fibre Channel card that is to be checked and press the [Enter] key.

4 Check the [Mem Base] and [Port Name] values.

The value of [Mem Base] is the physical address and the value of [Port Name] is the WWN.

Physical address

Fibre Channel card WWN

-------------------------------------------------------------------------------

Emulex LightPulse FC BIOS Utility, KA6.00a13

-------------------------------------------------------------------------------

01: LPe16002-M6: Bus#: 02 Dev#: 00 Func#: 00

Mem Base: CE000000 Firmware Version: 1.1.8.0 BIOS: Disabled

Port Name: 10000090FA02097E Node Name: 20000090FA02097E

Link Status: Link Down

-------------------------------------------------------------------------------

Enable/Disable Boot from SAN

Scan for Target Devices

Reset Adapter Defaults

Configure Boot Devices

Configure Advanced Adapter Parameters

Enter to Previous Menu

< / > to Highlight, to Select

The name of the physical address might be "I/O Base", " I/O Address", or "Mem Base", depending onthe HBA BIOS version. For more information about how to check the physical address, refer to the

HBA manual.

5 Record the physical address and WWN in the "WWN instance management table for the server".

(found in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 47)).

The following shows an example of this.

WWN instance management table for the server

Host name

IP Address

Physical slot

nameFibre Channel card WWN Instance name Physical address Cable tag

slot0 10000090FA02097E CE000000

Details of contents

The details of contents for the WWN instance management table for the server are as follows:

Host name:

Record the host name.




P3AM-6332-11ENZ0


13/58

IP Address:

Record the IP address of the server.

Physical slot name:

Record the slot position of the installed Fibre Channel card.

For the installation location, refer to the User's Guide for each server.

Fibre Channel card WWN:

Record the value of [Port Name] or [Adapter Port Name].

Instance name:

Not necessary to record.

Physical address:

Record the value of [I/O Base], [I/O Address], or [Mem Base].

Cable tag:

Record a tag name which indicates the connection path (relationship between the connected deviceand the port).

6 Select "Configure Advanced Adapter Parameters" and press the [Enter] key.

7 Select "Topology Selection" and press the [Enter] key.

8 Select "Auto Topology: Loop first (Default)" (for a direct connection) or "Fabric Point to Point" (for aswitch connection), and then press the [Enter] key.

When a direct connection is used and the LinkSpeed is 16Gbit/s, select "Fabric Point to Point".

9 Press the [Esc] key to return to the window shown in Step 7.

10 Select "Link Speed Selection" and press the [Enter] key.

11 Select the transfer rate according to the values listed in the LinkSpeed settings table below, and pressthe [Enter] key.

LinkSpeed settings

FibreChannelcard trans-fer rate

Switch connection

Fibre Channel switch transfer rate

Direct connection

CA transfer rate

16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 1Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s

16Gbit/s 16 8 4 16 8 4

8Gbit/s 8 8 4 2 8 8 4

4Gbit/s 4 4 4 2 1 4 4 4

2Gbit/s 2 2 2 1 2 2

12 Press the [Esc] key to quit the "Emulex LightPulse FC BIOS Utility".

When the total number of ports for installed Fibre Channel cards is two or more, first repeat Step 3through Step 11for each port, and then press the [Esc] key to exit "Emulex LightPulse FC BIOS Utility".




P3AM-6332-11ENZ0


14/58

If two or more Fibre Channel cards have already been installed in the server at the time of purchase,the one-to-one relationship between the WWNs and Fibre Channel cards may not be easy to deter-mine. The WWNs that are obtained in this section may need to be repeatedly registered and set up

on the ETERNUS DX until a server recognizes the ETERNUS DX logical disks.For details about ETERNUS DX settings, refer to the following manuals.

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX60 S3/DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk Storage Systems, ETERNUSDX200F All Flash Array Settings"

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX80 S2/DX90 S2, ETERNUS DX410 S2/DX440 S2, ETERNUS DX8100 S2/DX8700 S2 Disk Storage Sys-tem Settings"

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX60/DX60 S2, DX80, DX90 Disk Storage System Settings"

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS

DX400/DX8000 series Disk Storage System Settings"

1.2.2 Setting Up SAN Boot

Refer to "Server Support Matrix" to check the support status of SAN Boot and refer to the manual of the serv-er, OS, or the Fibre Channel card that is to be used.

When using a logical unit (LUN) of the ETERNUS DX storage systems as a boot disk, make sure that the LUNhas enough capacity to install the OS.

1.2.3 Installing Windows

Refer to the documentation supplied with the product for Windows installation details.

1.2.4 Installing the Driver

Refer to the documentation provided with each Fibre Channel card for details on how to obtain and install aFibre Channel card driver for it.




P3AM-6332-11ENZ0


15/58

1.2.5 Checking the Driver Version

Use the Device Manager to check the version of the Fibre Channel card driver.

1 In the Device Manager, go to [Storage controllers], and open the [Properties] of the Fibre Channel card.

2 Select the [Driver] tab, and open [Driver Details].

3 Select the driver file, and check its [File version].

If a different driver version is displayed from that shown in "Server Support Matrix", reinstall the driv-er.

1.2.6 Setting Up the Driver Parameters

The procedure depends on the type of Fibre Channel card that is being used.

For the 2Gbit/s Fibre Channel cards, proceed to "1.2.6.1 For 2Gbit/s Fibre Channel Cards" (page 15).

For 16Gbit/s Fibre Channel cards, 8Gbit/s Fibre Channel cards, or 4Gbit/s Fibre Channel cards, proceed to"1.2.6.2 For 16Gbit/s, 8Gbit/s, and 4Gbit/s Fibre Channel Cards" (page 17).

1.2.6.1 For 2Gbit/s Fibre Channel Cards

Set the driver parameters after installing HBAnyware.

1 Install HBAnyware.

For installation, refer to the Fibre Channel card manual.

The Driver Parameter Setting Tool (LightPulse Utility/NT) is included in HBAnyware.

2 Start up the "LightPulse Utility/NT".

3 Select [Driver Parameters] from [Category:].

4 Select [Registry] with the radio button.

The registry contents are displayed.




P3AM-6332-11ENZ0


16/58

The display contents vary according to the installed Fibre Channel card type and the driver version.

5 Double click [Device].The [Modify Registry Entry] dialog box is displayed.

6 Check the current values of each parameter.

Compare with the parameter values in the tables below, and correct the current value if necessary.

If the parameter is not shown, add the necessary information.

For Windows Server2003

Fibre Channel cardtransfer rate

Setting value

Topology QueueDepth Queue Target LinkSpeed

2Gbit/s 0 (direct connection)

1 (switch connection)

Arbitrary (*1)

(Up to 512 for eachFC port of the ETER-NUS DX)

0 2 (direct connection)

2 (8Gbit/s switch con-nection)




*1: Recommended value = 512 (number of Fibre Channel ports that are connected to a single CAport) number of LUNs

(Round the result down)

Use the value of "8" if the actual result is lower.

If correcting or adding parameters, note the following restrictions.

Describe each parameter, using ";" (semicolon) to delimit.

Enter each parameter, using correct spelling. Note that misspelled words are not checked.

Do not modify any parameters other than those described here.

The following describes each parameter: "Topology" parameter

Set the connection configuration between the server and ETERNUS DX storage systems.

"QueueDepth" parameter

Set the command queue depth.

"QueueTarget" parameter

Set to specify the command queue depth to either the LUN or to the target.

"LinkSpeed" parameter

Set the link speed.




P3AM-6332-11ENZ0


17/58

7 After all the cards have been set, select [Exit] from the [File] menu to quit the "LightPulse Utility/NT".

1.2.6.2 For 16Gbit/s, 8Gbit/s, and 4Gbit/s Fibre Channel CardsSet the driver parameters after installing OneCommand Manager.

When the server OS is Windows Server2012 R2, Windows Server2012, Windows Server2008 R2, Windows

Server2008, or Windows Server2003, it is recommended that fixed Target IDs be assigned to the FibreChannel card connected devices, and that automatic Target ID allocation be disabled.

For details of the Target ID settings, refer to the "Fibre Channel Controller User's Guide".

By default, Target IDs are automatically allocated. However, when a device is added, automatic Target IDallocation can result in a different distribution of Target IDs, which can cause the devices to not be recog-

nized.

1 Install OneCommand Manager.

For installation, refer to the Fibre Channel card manual.

2 Start OneCommand Manager.

3 Select the target Fibre Channel card port and click the [Driver Parameters] tab.




P3AM-6332-11ENZ0


18/58

4 Check the parameter values in the [Adapter Parameter] list.

Compare with the parameter values in the following tables, and correct the current value if necessary.

Select the parameter whose value is to be corrected from the [Adapter Parameter] list and modify thevalue in the [Modify Adapter Parameter] area.

For Windows Server2012 R2, Windows Server2012, or Windows Server2008 R2


Setting value


16Gbit/s

8Gbit/s

4Gbit/s

0 (direct connection)


When a direct con-nection is used andthe LinkSpeed is16Gbit/s, select "1".

Arbitrary (*1)

(Up to 512 for each

FC port of the ETER-NUS DX)

0 (*2)




*2: LinkSpeed setting value list:

FibreChannelcardtransferrate

Switch connection


Direct connection

CA transfer rate


16Gbit/s 16 8 4 16 8 4

8Gbit/s 8 8 4 2 8 8 4

4Gbit/s 4 4 4 2 1 4 4 4




P3AM-6332-11ENZ0


19/58

For Windows Server2008 or Windows Server2003


Setting value


8Gbit/s

4Gbit/s

0 (direct connection)


Arbitrary (*1)

(Up to 512 for eachFC port of the ETER-NUS DX)

0 (*2)





Fibre

Channelcardtransferrate

Switch connection


Direct connection

CA transfer rate


8Gbit/s 8 8 4 2 8 8 4

4Gbit/s 4 4 4 2 1 4 4 4


The following describes each parameter:

"Topology" parameter







Set the link speed.

5 After the values have been modified, click the [Apply] button.Parameters that are displayed in red in the [Adapter Parameter] column show that their values havebeen modified but not yet applied. Click the [Apply] button to apply the changed values.

6 If there are multiple cards, repeat Step 2through Step 5to change the settings for all cards.

7 After all the cards have been set, select [Exit] from the [File] menu to quit OneCommand Manager.




P3AM-6332-11ENZ0


20/58


21/58





(4) Add a record for the server in the WWN instance management table for the server(5) Set the Fibre Channel card BIOS

When installing two or more Fibre Channel cards in the server, first turn off the server, then repeat Steps (1)through (5) above for each Fibre Channel card to be installed.



For the installation method, position (PCI bus slots), and notes regarding the Fibre Channel card, referto the Fibre Channel card manual or the user guide of the server.

2 Turn on the server, and press the [Ctrl] + [Q] keys while the following message is displayed.

QLogic Corporation

QLA23xx PCI Fibre Channel ROM BIOS Version *.**

Copyright(C) QLogic Corporation 2000. All rights reserved

www.qlogic.com

Press for Fast!UTIL

The "Fast!UTIL" program starts up (Startup may take longer than usual).

3 Check the value of [I/O Address] of the [Select Host Adapter] window.

The value of [I/O Address] is the physical address.

Adapter Type

QLA2xxx

I/O Address

3400

Select Host Adapter

Physical

address

4 Select [Configuration Settings] from the [Fast!UTIL Options] menu and press the [Enter] key.

5 Select [Host Adapter Settings] from the [Configuration Settings] menu and press the [Enter] key.

6 Check the value of [Adapter Port Name].

The value of [Adapter Port Name] is the Fibre Channel card WWN.Host Adapter Settings

BIOS Address

BIOS Revision

Adapter Serial Number

Interrupt Level

Adapter Port Name

Host Adapter BIOS

:xxxxx

:x.xx

:xxxxxx

:xx

:200000E08B0214D0

:Disabled



Chapter 1 Setup Procedure for PRIMERGY1.3 For Fujitsu QLogic Fibre Channel Cards



P3AM-6332-11ENZ0


22/58


Host name Server#1

IP Address 192.168.0.10

Physical slot

nameFibre Channel card WWN Instance name Physical address Cable tag

slot0 20 00 00 E0 8B 02 14 D0 3400 SERV1_SLOT0 to SN200_1_port0

8 Set up the BIOS parameters for the Fibre Channel card.

Check the values for each parameter in the [Host Adapter Settings] window. See the following tablesand set each value. For details on how to set the values, refer to the BIOS Readme file and Fibre Chan-nel card user's guide.

Parameter Host Adapter settings value Remarks

BIOS Address Fixed for each card Settings cannot be changed.

BIOS Revision (*1)


Interrupt Level

Adapter Port Name

Host Adapter BIOS Enabled or Disabled Set "Enabled" for SAN Boot.

Set "Disabled" for non SAN Boot.

Frame Size 2048 If the current parameter values are dif-ferent, change them to the indicated

values.Loop Reset Delay 5Adapter Hard Loop ID Disabled

Hard Loop ID 0

Spinup Delay Disabled

Connection Options 0 or 1 For direct connection: 0 (*2)

For switch connection: 1 (*3)

Fibre Channel

Tape Support

Disabled If "Enabled" is displayed, change thevalue to "Disabled".

Data Rate (*4) 1: 2Gbit/s fixed

2: Auto-negotiated

3: 4Gbit/s fixed

4: 8Gbit/s fixed

5: 16Gbit/s fixed

*1: The BIOS version of the Fibre Channel card is displayed. Check that the BIOS version is the same asshown in "Server Support Matrix".

*2: When connecting directly to the ETERNUS DX storage systems via a Fibre Channel pass-throughblade

However, select "1" for direct connections with 16Gbit/s Fibre Channel cards.

*3: When the Fibre Channel switch is connected to the ETERNUS DX storage systems via a Fibre Chan-nel pass-through blade or Fibre Channel switch blade.




P3AM-6332-11ENZ0


23/58


24/58


25/58

7 Select [Exit Fast!UTIL] and press the [Enter] key.

8 Select [Reboot System] and press the [Enter] key.

Reboot System

Return to Fast!UTIL

Exit Fast!UTIL

The server reboots.

To return to the [Fast!UTIL] menu, select [Return to Fast!UTIL].

1.3.3 Installing WindowsRefer to the documentation supplied with the product for Windows installation details.



1.3.5 Checking the Driver Version






1.3.6 Setting Up the Driver Parameters

Set the driver parameters using the following procedure.




P3AM-6332-11ENZ0


26/58


27/58


28/58

(3) Move to the path as shown below:

HKEY_LOCAL_MACHINE

\SYSTEM

\CurrentControlSet

\Services \ql2300 \Parameters

\Device

(4) Double click [DriverParameter].

(5) Enter the Queue Depth value (qd="recommended value") in "Value data" and click the [OK] but-ton.

Recommended value = 512 (number of Fibre Channel ports that are connected to a single CAport) number of LUNs



Use the value of "254" if the actual result is higher.

(6) Close the Registry Editor.

9 Reboot the server.

1.3.7 Installing the ETERNUS DX Driver

Install the driver for ETERNUS DX storage systems as required.

Refer to the "Driver Notes" section in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

(Fibre Channel) for Windows" for notes on each driver in cases such as when connecting the server to theETERNUS DX in multipath configuration and using the path redundancy control (path fail-over) function,

and for when single-path connection is used between the ETERNUS DX and server.




P3AM-6332-11ENZ0


29/58

For the procedure about how to install (or uninstall), set up, and use the drivers for ETERNUS DX storagesystems, refer to the software manuals.




P3AM-6332-11ENZ0


30/58

Chapter 2Setup Procedure for PRIMEQUEST 1000 Series

This chapter describes how to install and set up the Fibre Channel cards in the PRIMEQUEST 1000 series.

2.1 Workflow

Workflow

Installing the Fibre Channel Card

Install the Fibre Channel card and its driver, check the driver version, and set up the Fibre Channelcard BIOS.




Setting Up the Driver Parameters

Set the Topology, QueueDepth and other parameters.

For Fujitsu Emulex Fibre Channel Cards




P3AM-6332-11ENZ0


31/58



For Fujitsu Emulex Fibre Channel Cards

- "2.2.6 Installing the ETERNUS DX Driver" (page 38)- Checking the driver-related notes


dows"


Windows".

Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series2.1 Workflow



P3AM-6332-11ENZ0


32/58

2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards

If a SAN boot environment is to be set up, the SAN boot settings must be made beforehand for the PRIME-QUEST 1000 series. Refer to "PRIMEQUEST 1000 Series SAN Boot Environment Configuration Manual" fordetails.

2.2.1 Setting Up the Fibre Channel Cards

Install the Fibre Channel cards in the server, acquire the relevant physical addresses and World Wide Names(WWNs), and perform Topology and LinkSpeed settings.

The physical address and WWN of a Fibre Channel card are required information in the following cases:when an error has occurred in the system, when using the ETERNUS DX storage systems (security function,

host affinity function, etc.) to restrict server access, or when connecting the ETERNUS DX storage systemsand the server using a Fibre Channel switch.

The relationship between a physical address and WWN cannot be determined from BIOS and OS. The physi-cal address and WWN must be recorded as a pair when each Fibre Channel card is installed. Physical ad-dress and WWN must be assigned to "WWN instance management table for the server".





(4) Add a record for the server in the WWN instance management table for the server

(5) Set the Topology and LinkSpeedWhen installing two or more Fibre Channel cards in the server, first turn off the server, then repeat Steps (1)through (5) above for each Fibre Channel card to be installed.



For the installation method, slot positions, and notes regarding the Fibre Channel card, refer to themanual provided with the Fibre Channel card or the user guide of the server.

2 Turn on the server, and press the [Alt] + [E] keys or [Ctrl] + [E] keys while the following message isdisplayed.

!!! Emulex LightPulse x86 BIOS !!!, Version xxxxxx

Copyright (c)1997-2010 Emulex.All rights reserved.

Press or to enter Emulex BIOS configuration

utility. Press to skip Emulex BIOS.

"LightPulse BIOS Utility" starts.

3 Select the port for the Fibre Channel card that is to be checked and press the [Enter] key.

Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards



P3AM-6332-11ENZ0


33/58

4 Check the [Mem Base] and [Port Name] values.

The value of [Mem Base] is the physical address and the value of [Port Name] is the WWN.

Physical address

Fibre Channel card WWN

-------------------------------------------------------------------------------

Emulex LightPulse FC BIOS Utility, KA6.00a13

-------------------------------------------------------------------------------01: LPe16002-M6: Bus#: 02 Dev#: 00 Func#: 00

Mem Base: CE000000 Firmware Version: 1.1.8.0 BIOS: Disabled

Port Name: 10000090FA02097E Node Name: 20000090FA02097E

Link Status: Link Down

-------------------------------------------------------------------------------

Enable/Disable Boot from SAN

Scan for Target Devices

Reset Adapter Defaults

Configure Boot Devices

Configure Advanced Adapter Parameters

Enter to Previous Menu

< / > to Highlight, to Select

The name of the physical address might be "I/O Base", " I/O Address", or "Mem Base", depending onthe HBA BIOS version. For more information about how to check the physical address, refer to theHBA manual.




WWN instance management table for the server

Host name

IP Address

Physical slotname

Fibre Channel card WWN Instance name Physical address Cable tag

slot0 10000090FA02097E CE000000

Details of contents

The details of contents for the WWN instance management table for the server are as follows:

Host name:


IP Address:





P3AM-6332-11ENZ0


34/58

Physical slot name:



Fibre Channel card WWN:

Record the value of [Port Name] or [Adapter Port Name].

Instance name:


Physical address:

Record the value of [I/O Base], [I/O Address], or [Mem Base].

Cable tag:

Record a tag name which indicates the connection path (relationship between the connected deviceand the port).

6 Select "Configure Advanced Adapter Parameters" and press the [Enter] key.

7 Select "Topology Selection" and press the [Enter] key.

8 Select "Auto Topology: Loop first (Default)" (for a direct connection) or "Fabric Point to Point" (for aswitch connection), and then press the [Enter] key.

9 Press the [Esc] key to return to the window shown in Step 7.

10 Select "Link Speed Selection" and press the [Enter] key.

11 Select the transfer rate according to the values listed in the LinkSpeed settings table below, and pressthe [Enter] key.

LinkSpeed settings

FibreChannelcard trans-fer rate

Switch connection


Direct connection

CA transfer rate


8Gbit/s 8 8 4 2 8 8 4

4Gbit/s 4 4 4 2 1 4 4 4

2Gbit/s 2 2 2 1 2 2

12 Press the [Esc] key to quit the "Emulex LightPulse FC BIOS Utility".

When the total number of ports for installed Fibre Channel cards is two or more, first repeat Step 3through Step 11for each port, and then press the [Esc] key to exit "Emulex LightPulse FC BIOS Utility".




P3AM-6332-11ENZ0


35/58

If two or more Fibre Channel cards have already been installed in the server at the time of purchase,the one-to-one relationship between the WWNs and Fibre Channel cards may not be easy to deter-mine. The WWNs that are obtained in this section may need to be repeatedly registered and set up

on the ETERNUS DX until a server recognizes the ETERNUS DX logical disks.For details about ETERNUS DX settings, refer to the following manuals.

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX60 S3/DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk Storage Systems, ETERNUSDX200F All Flash Array Settings"

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX80 S2/DX90 S2, ETERNUS DX410 S2/DX440 S2, ETERNUS DX8100 S2/DX8700 S2 Disk Storage Sys-tem Settings"

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX60/DX60 S2, DX80, DX90 Disk Storage System Settings"

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS

DX400/DX8000 series Disk Storage System Settings"



2.2.3 Checking the Driver VersionUse the Device Manager to check the version of the Fibre Channel card driver.

1 In the Device Manager, go to [Storage Area controllers], and open the [Properties] of the Fibre Channelcard.







P3AM-6332-11ENZ0


36/58


37/58


Fibre Chan-nel cardtransferrate

Switch connection


Direct connection

CA transfer rate

16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s

8Gbit/s 8 8 4 2 8 8 4


The following describes each parameter:

"Topology" parameter







Set the link speed.

5 After the values have been modified, click the [Apply] button.

Parameters that are displayed in red in the [Adapter Parameter] column show that their values havebeen modified but not yet applied. Click the [Apply] button to apply the changed values.

6 If there are multiple cards, repeat Step 2through Step 5to change the settings for all cards.

7 After all the cards have been set, select [Exit] from the [File] menu to quit OneCommand Manager.

2.2.5 Setting Fixed Target IDs

Each device connected to a Fibre Channel card is allocated a Target ID. By default, these Target IDs are auto-matically allocated by the driver. Under this default, the device Target IDs may be reallocated as devices areadded and removed, or depending on how the devices are recognized. If the Target IDs have changed when

the server reboots, devices may end up off-line, and unavailable depending on the OS or application beingused. To avoid this, it is recommended that a fixed Target ID be allocated to each device and automatic Tar-get ID allocation be disabled.

Contact your supplier for more details.




P3AM-6332-11ENZ0


38/58

2.2.6 Installing the ETERNUS DX Driver

Install the driver for ETERNUS DX storage systems as required.

Refer to the "Driver Notes" section in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

(Fibre Channel) for Windows" for notes on each driver in cases such as when connecting the server to the

ETERNUS DX in multipath configuration and using the path redundancy control (path fail-over) function,and for when single-path connection is used between the ETERNUS DX and server.

For the procedure about how to install (or uninstall), set up, and use the drivers for ETERNUS DX storagesystems, refer to the software manuals.




P3AM-6332-11ENZ0


39/58

Chapter 3Setup Procedure for PRIMEQUEST 500/400 Series

This chapter describes how to install and set up the Fibre Channel cards in the PRIMEQUEST 500/400 series.

3.1 Workflow

Workflow

Installing the Fibre Channel Card

Install the Fibre Channel card and acquire WWPN information.



- "Appendix A WWN Instance Management Table for the Server (Blank)" (page 47)

- Checking the WWPN acquisition procedure

"PRIMEQUEST 500A/500/400 SERIES INSTALLATION MANUAL"





- Checking how to obtain and install the Fibre Channel card driver

Fibre Channel card documentation



P3AM-6332-11ENZ0


40/58


41/58




(3) Acquire the physical address and WWPN for the Fibre Channel card

(4) Add a record for the server in the WWN instance management table for the server(5) Set the Topology and LinkSpeed


Host name

IP Address

Physical slot name Fibre Channel card WWN Instance name Physical address Cable tag

slot0 10 00 00 00 C9 38 D2 29 5000

Details of contents

The details of contents for the WWPN instance management table for the server are as follows:

Host name:


IP Address:


Physical slot name:



Fibre Channel card WWPN:

Record the WWPN of the Fibre Channel card.

Instance name:


Physical address:

Record the value of [I/O Base] or [I/O Address].

Cable tag:

Record a tag name which indicates the connection path (relationship between the connected device andthe port).

Topology

Set the Topology according to the system configuration that is used:

For direct connections: "1. Auto Topology: Loop first (Default)"

For switch connections: "4. Fabric Point to Point"

Chapter 3 Setup Procedure for PRIMEQUEST 500/400 Series3.2 For Fujitsu Emulex Fibre Channel Cards



P3AM-6332-11ENZ0


42/58

LinkSpeed

Set the link speed according to the values listed in the following table.

Fibre Chan-nel cardtransferrate

Switch connection


Direct connection

CA transfer rate


8Gbit/s 8 8 4 2 8 8 4

4Gbit/s 4 4 4 2 1 4 4 4

2Gbit/s 2 2 2 1 2 2


If two or more Fibre Channel cards have already been installed in the server at the time of purchase, theone-to-one relationship between the WWPNs and Fibre Channel cards may not be easy to determine. TheWWPNs that are obtained in this section may need to be repeatedly registered and set up on the ETERNUSDX until a server recognizes the ETERNUS DX logical disks.

For details about ETERNUS DX settings, refer to the following manuals.

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX60S3/DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk Storage Systems, ETERNUS DX200F All FlashArray Settings"

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX80S2/DX90 S2, ETERNUS DX410 S2/DX440 S2, ETERNUS DX8100 S2/DX8700 S2 Disk Storage System Set-tings"

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX60/DX60 S2, DX80, DX90 Disk Storage System Settings"

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX400/DX8000 series Disk Storage System Settings"






P3AM-6332-11ENZ0


43/58


44/58

3 Select the target Fibre Channel card port and click the [Driver Parameters] tab.

4 Check the parameter values in the [Adapter Parameter] list.

Compare with the parameter values in the following tables, and correct the current value if necessary.Select the parameter whose value is to be corrected from the [Adapter Parameter] list and modify thevalue in the [Modify Adapter Parameter] area.




P3AM-6332-11ENZ0


45/58


46/58


47/58


48/58


49/58



"B.5 Installing the Driver" (page 55)

"B.6 Checking the Driver Version" (page 55)



"B.7 Installing the ETERNUS DX Driver" (page 56)

Checking the driver-related notes

"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Win-dows"


Windows".

Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s)B.1 Workflow



P3AM-6332-11ENZ0


50/58

B.2 Setting Up the Fibre Channel Cards

Install the Fibre Channel cards in the server, and acquire their physical addresses and World Wide Names(WWNs).

The physical address and WWN of a Fibre Channel card are required information in the following cases:when an error has occurred in the system, when using the ETERNUS DX storage systems (security function,host affinity function, etc.) to restrict server access, or when connecting the ETERNUS DX storage systemsand the server using a Fibre Channel switch.

Acquire the physical address and WWN when installing the Fibre Channel card, because they cannot bedetermined from BIOS and OS. Physical address and WWN must be assigned to "WWN instance manage-ment table for the server".




(3) Acquire the physical address and WWN for the Fibre Channel card(4) Add a record for the server in the WWN instance management table for the server

(5) Set the Fibre Channel card BIOS



1 Install the Fibre Channel card in the server.For the installation method, position (PCI bus slots), and notes regarding the Fibre Channel card, referto the Fibre Channel card manual or the user guide of the server.

2 Turn on the server, and press the [Ctrl] + [Q] keys while the following message is displayed.

QLogic Corporation

QLA23xx PCI Fibre Channel ROM BIOS Version *.**

Copyright(C) QLogic Corporation 2000. All rights reserved

www.qlogic.com

Press for Fast!UTIL

The "Fast!UTIL" program starts up (Startup may take longer than usual).

3 Check the value of [I/O Address] of the [Select Host Adapter] window.

The value of [I/O Address] is the physical address.

Adapter Type

QLA2xxx

I/O Address

3400

Select Host Adapter

Physical

address

4 Select [Configuration Settings] from the [Fast!UTIL Options] menu and press the [Enter] key.

5 Select [Host Adapter Settings] from the [Configuration Settings] menu and press the [Enter] key.

Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s)B.2 Setting Up the Fibre Channel Cards



P3AM-6332-11ENZ0


51/58

6 Check the value of [Adapter Port Name].

The value of [Adapter Port Name] is the Fibre Channel card WWN.Host Adapter Settings

BIOS Address

BIOS Revision

Adapter Serial NumberInterrupt Level

Adapter Port Name

Host Adapter BIOS

:xxxxx

:x.xx

:xxxxxx:xx

:200000E08B0214D0

:Disabled




Host name Server#1

IP Address 192.168.0.10

Physical slot

name Fibre Channel card WWN Instance name Physical address Cable tag

slot0 20 00 00 E0 8B 02 14 D0 3400 SERV1_SLOT0 to SN200_1_port0

8 Set up the BIOS parameters for the Fibre Channel card.

Check the values for each parameter in the [Host Adapter Settings] window. See the following tablesand set each value. For details on how to set the values, refer to the BIOS Readme file and Fibre Chan-nel card user's guide.

Parameter Host Adapter settings value Remarks

BIOS Address Fixed for each card Settings cannot be changed.

BIOS Revision (*1)


Interrupt Level

Adapter Port Name

Host Adapter BIOS Enabled or Disabled Set "Enabled" for SAN Boot.

Set "Disabled" for non SAN Boot.

Frame Size 2048 If the current parameter values are dif-ferent, change them to the indicated

values.Loop Reset Delay 5Adapter Hard Loop ID Disabled

Hard Loop ID 0

Spinup Delay Disabled

Connection Options 0 or 1 For direct connection: 0 (*2)

For switch connection: 1 (*3)

Fibre Channel

Tape Support

Disabled If "Enabled" is displayed, change thevalue to "Disabled".

Data Rate 1 0: 1Gbit/s fixed

1: 2Gbit/s fixed

2: Auto-negotiated




P3AM-6332-11ENZ0


52/58

*1: The BIOS version of the Fibre Channel card is displayed. Check that the BIOS version is the same asshown in "Server Support Matrix".

*2: When connecting directly to the ETERNUS DX storage systems via a Fibre Channel pass-throughblade

*3: When the Fibre Channel switch is connected to the ETERNUS DX storage systems via a Fibre Chan-nel pass-through blade or Fibre Channel switch blade.

9 Return to the [Configuration Settings] menu by pressing the [Esc] key.

10 Select [Advanced Adapter Settings] from the [Configuration Settings] menu and press the [Enter] key.

Compare with the parameter values in the following tables, and correct the current value if necessary.

Parameter Advanced HBA Parameter settings Remarks

Execution Throttle Arbitrary (*1)

(Up to 512 for each FC port of theETERNUS DX)

If the current parameter values are dif-ferent, change them to the indicatedvalues.

LUNs per Target 256

Enable LIP Reset No

Enable LIP Full Login Yes

Enable Target Reset Yes

Login Retry Count 8

Port Down Retry Count 45

Link Down Timeout 45

Extended Error Logging Disabled

RIO Operation Mode 0

Interrupt Delay Timer 0

EV Controller Order Disabled




Use the value of "254" if the actual result is higher.

11 Press the [Esc] key twice to return to the [Fast!UTIL Options] menu.

If the BIOS settings were changed, save the settings using [Save xxxxxx]. When two or more FibreChannel cards are installed in the server, select the second or later Fibre Channel card using the follow-ing steps, and set the BIOS of the selected card.

(1) Select [Select Host Adapter] from the [Fast!UTIL Options] menu and press the [Enter] key.

(2) Select the Fibre Channel card to be set (BIOS setting) in the [Select Host Adapter] window.

The [Fast!UTIL Options] menu appears. Then perform Step 3through Step 11.





P3AM-6332-11ENZ0


53/58


54/58

4 Check the values for each parameter.

Selectable Boot

Boot Port Name, Lun

:Disabled

:0000000000000000,0

Selectable Boot Settings

Parameter Setting value Remarks

Selectable Boot Enabled or Disabled Set [Enabled] for SAN Boot.

Set [Disabled] for non SAN Boot.

Boot Port Name, Lun ETERNUS DX port WWN, LUN#

or 0000000000000000,0

The boot path (ETERNUS DX port WWN)and boot LUN# for SAN Boot are separated

by a comma. "0000000000000000,0" for non SAN Boot.

5 Return to the [Configuration Settings] menu by pressing the [Esc] key.

6 Press the [Esc] key twice to return to the [Fast!UTIL Options] menu.

If the settings were changed, save the settings using [Save xxxxxx].

When two or more Fibre Channel cards are installed in the server, select the second or later Fibre Chan-nel card using the following steps, and set the BIOS of the selected card.

(1) Select [Select Host Adapter] from the [Fast!UTIL Options] menu and press the [Enter] key.

Fast!UTIL Options

Configuration Settings

Scan Fibre Devices

Fibre Disk Utility

Select Host Adapter

Exit Fast!UTIL

Fast!UTIL Options

(2) Select the Fibre Channel card to be set (BIOS setting).

Adapter Type I/O AddressQLA2xxx

QLA2xxx

3400

3800

Select Host Adapter

(3) The [Fast!UTIL Options] menu appears. Then perform Step 1through Step 6.


Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s)B.3 Setting Up SAN Boot



P3AM-6332-11ENZ0


55/58

8 Select [Reboot System] and press the [Enter] key.

Reboot System

Return to Fast!UTIL

Exit Fast!UTIL

The server reboots.

To return to the [Fast!UTIL] menu, select [Return to Fast!UTIL].

B.4 Installing Windows

Refer to the documentation supplied with the product for Windows installation details.

B.5 Installing the Driver


B.6 Checking the Driver Version






Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s)B.4 Installing Windows



P3AM-6332-11ENZ0


56/58


57/58

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-

(Fibre Channel) for Windows

Driver Settings for Fujitsu Fibre Channel Cards

P3AM-6332-11ENZ0

Date of issuance: December 2014Issuance responsibility: FUJITSU LIMITED

The content of this manual is subject to change without notice.

This manual was prepared with the utmost attention to detail. However, Fujitsu shall assume no responsibility for anyoperational problems as the result of errors, omissions, or the use of information in this manual.

Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any informationin this manual.

The content of this manual may not be reproduced or distributed in part or in its entirety without prior permission fromFujitsu.


58/58

Server Connection- (Fibre Channel) - Fujitsu

Documents

Transcript of Server Connection- (Fibre Channel) - Fujitsu