Serto tool serto matic
-
Upload
teesing-bv -
Category
Documents
-
view
219 -
download
0
description
Transcript of Serto tool serto matic
USP’S SERTOTOOL/SERTOMATIC:• Pre assembling• Sertotool sizes: 4-10 mm Sertomatic sizes: 10-35 mm • A constant quality, same tightening torque • No friction on the surface due to axial assembly• Ergonomic. Low physical power needed, the Sertomatic is activated with foot switch• Special adapters for constant quality• Easy and fast assembling of larger sized couplings• Timesaving: 30 seconds, compared with traditional method 3 minutes, per assembly with the Sertotool• Saves a lot more time while assembling larger sizes• Suitable for construction areas
Example:700 couplings per year, means 1400 assemblies.
Time/assembly: Assemblies/Hour Total assembly time
Normal 3 min 20 70 Hour
SERTO-tool 30 sec 120 12 Hour
*Saves 58 hours!
SERTOMATICFor assembling larger diameters we prefer to use the SERTOmatic. SERTOmatic is equiped with a strong electro-hydraulic pump which allows fast assembling of all serto couplings. The SERTOmatic is suitable for assembling couplings up to 35 mm diameter.
SERTOTOOLThe SERTO pre-assembly tool is driven by compressed air and can be set up easily anywhere due its small size and light weight. Each device has a rotatable tool insert, which is suitable for a specific material (M brass, stainless steel, stainless SOL, etc.) and can not be misplaced.
TEL +31 70 413 07 50 | WWW.TEESING.COM
SAVES A LOT OF TIME WHILEASSEMBLING SERTO COUPLINGS
APPROVED DIMENSIONAL DEVIATIONS
Material Outside tolerance Tolerance thicknessSt 35.4 ± 0.08 mm ± 0.10 mm
INOX ± 0.1 mm ± 0.15 mm
Cu 3 - 6 mm: ± 0.07 mm6.35 - 10 mm: ± 0.09 mm
12 - 18 mm: ± 0.12 mm19.05 - 28 mm: ± 0.18 mm
35 mm: ± 0.24 mm
± 0.10 mm
PA 11W12W 6 - 10 mm: ± 0.10 mm12 - 18 mm: ± 0.15 mm
± 0.08 mm
PE ± 0.10 mm ± 0.10 mm
PU + 0.10 mm-0.05 mm
± 0.10 mm
PTFE ± 0.10 mm ± 0.10 mm
PVDF ± 0.10 mm ± 0.10 mm
SERTOflex 6 - 8 mm: +0.13 mm-0.28 mm
10 - 12 mm: + 0.15 mm - 0.30 mm
15 mm: + 0.20 mm- 0.35 mm
± 0.10 mm
FEP 4 - 6 mm: ± 0.10 mm8 - 12 mm: ± 0.15 mm
± 0.15 mm
LATEST IMPROVEMENTSTeesing supplies with serto a complete program of fittings incl. a complete range of tool inserts. Every material and pipe diameter requires it’s own tool insert (see table below). The SERTOtool and SERTOmatic avoid the damaging of the couplings, due to a correct positioning after inserting the pipe connection nut and clamping ring.
Space between nut across corners and holdersadjusted to 0.4 mm
Changed 0.4 mm - diameter bolt on thread diameterradiusing 0.2 mm instead of 45 bevel Levers to the position of nut and clamping ring
bolt material changed from 1.4305 to 1.6582
TEL +31 70 413 07 50 | WWW.TEESING.COM
MASS PRODUCTION MADE EASY
ADDITIONAL SERVICESThe SERTOtool and SERTOmatic are available for rent with a compressed air cylinder, so it can be used on any construction area without an electrical power source.