User Manual

i3-TRNG-CAMS-Am52R-UM.indd Rev. 161123

HD1080P (2MP) Vandal-Proof Infrared Dome Camera Am52 Series

SAFETY When installing your Am52 series cameras be sure to avoid:• excessive heat, such as direct sunlight or heating appliances• contaminants such as dust and smoke• strong magnetic fields• moisture and humidity• areas with mechanical vibrations• fluorescent lamps or objects that reflect light and unstable light sources • temperatures below -30° C (-22° F) and above 60° C (140° F).

POWER SUPPLYEnsure the supplied voltage meets the power consumption requirements of this camera before powering the camera on. Incorrect voltage may cause irreparable damage to the video camera and will effectively void the camera warranty.This camera series accepts DC 12V and AC 24V power.

CLEANING• For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,

dry cloth to remove finger prints or dust from the dome cover.• Use a blower to remove dust from the lens.• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may

damage the surface finishes.

SERVICINGTo avoid electrical shock and to preserve the product warranty, DO NOT disassemble the camera. Refer servicing to qualified personnel only.

PACKAGE CONTENTSEnsure that the items received match those listed on the order form and the packing slip. In addition to this manual and a fully assembled camera, the dome camera packing box includes:1. Security Torx bit x12. Plastic Anchor x4 3. Round Head Screw (Tapping Type) x44. Spot monitor auxiliary video output cable x15. Surface Mount template x1

1. 3-axis camera module / second housing.2. Long screws (pre-installed) for attaching camera module to the back box, x3. 3. Lens.4. IR board.5. Lens focus adjustment w/ locking screw (Far / Near).6. Lens zoom adjustment w/ locking screw (Tele / Wide).7. Joystick (for on-screen camera menu control)8. Dip switch (CVBS / WDR). Remove the Shroud/Liner for easy access. When the

switch is set to CVBS, the Service Monitor and CVBS output is enabled, True WDR is disabled. When the switch is set to WDR, the Service Monitor and CVBS output is disabled but WDR is enabled.

9. 2-pin Service (spot) monitor output.10. Power connector (12DC / 24AC).11. TVI High-definition analog video connector (2MP. 1920x1080 = 1080P).

To use high-definition analog stream (2MP), the camera must be connected to i3’s HR16 encoder or standalone Veo17 DVR.

12. CVBS standard-format analog video connector (4CIF = 720x480). Can be connected directly to the BNC board on the i3’s HVR units or to a spot monitor.

13. Lexan Bubble (Dome).14. Inner liner / Shroud (Removable for convenient lens position adjustments).15. Screws attaching camera bubble to the camera module (x3, silver).16. Camera’s back box.

Compatible with i3’s DB60/DB60B Goose-neck bracket. Can also be used for pendant mount installations.

17. Side conduit hole (3/4”). Remove plug to route power and video cables through the side opening. Use the plug for the top conduit hole in that scenario. When using outdoors, sealant must be used to maintain the IP66 status.

18. Top conduit hole (3/4”). Can also be used for pendant mount installations. When using outdoors, sealant must be used to maintain the IP66 status.

19. Mounting holes, partially drilled, x6 (complete drilling the holes prior to installation).

CAMERA PARTS AND DEFINITIONS

41 2 3 5

Lens Direction

GUIDE PATTERN

HIGH-DEFINITION ANALOG VIDEO SUPPORTYour Am52 Series cameras supports both the standard composite analog video stream (720x480) and a high-definition TVI video stream (HD-TVI = 2MP). Both streams are supported simultaneously. IMPORTANT: In order to use high-definition video, your Am52R camera must be connected to i3’s HR16 video encoder or standalone Veo17 DVR. To record camera’s HD-TVI stream (2MP) to SRX-Pro Server, connect the camera’s gray BNC cable connector (labeled 2MP) to i3’s HR16 encoder or standalone Veo17 DVR. If connecting directly to the HVR’s BNC panel, use 720x480 composite video cable.Alternatively, to use the CVBS stream for the spot monitor, connect the camera’s black BNC cable (labeled 720x480) directly to the spot monitor.

3

56

10

1112

78

9

CVBSWDR

13

15

16

19

17

18

14

2MP

720x4804

UP

1

2

2

The Am52 indoor/outdoor series cameras include the Am52R and the Am52RB.• Am52R comes in white.• Am52RB comes in black

USER MANUAL

Page -2-

Am52 Series Analog Dome Camera

Joystick

UP

Focus Lever + locking screw

(Far/Near)

F N

Zoom Lever + locking screw

(Tele/Wide)T W

UP

3-axis Range Limitations:

Pan:0 - 355°

Tilt: 0 - 75°

Rotation:0 - 355°

10. Connect camera to 12DC or 24AC power and attach the service monitor to the 2-pin connector on the camera. Make sure the dipswitch is set to CVBS to enable Service Monitor.

11. Adjust the lens angle by panning and tilting the camera lens assembly and rotating the camera lens base. Do not over-rotate the camera lens beyond the stop point to avoid damage to the camera.

CVBS / WDR dipswitch

2-pin Service Monitor connector

13. Use the joystick on the camera board to adjust any additional camera settings (e.g. image brightness, colour or contrast, day/night mode, etc.). See CAMERA MENU section for more information on camera’s on-screen menu.

14. Once the desired view is achieved, unplug the service monitor and switch the dip switch back into WDR mode (if using). Replace camera’s inner liner (shroud) until it snaps back into place.

15. Replace the camera dome bubble and re-tighten 3 silver screws securing the dome bubble to the camera base.

Joystick

FLUSH MOUNTINGAm52 Series cameras can be flush mounted with the use of i3’s flush mounting kit (Part # AM42FM for the AM42R and AM42FMB for the AM42RB). Sold separately. When flush-mounting the camera, do not use the supplied camera back box. Follow the mounting instructions supplied with the kit.

WALL MOUNTING w/ GOOSENECK BRACKET

12. Adjust the camera’s zoom and focus using Zoom / Focus levers on the camera module. Loosen the locking screws, adjust the lever and re-tighten the locking screw when desired view is achieved. Use camera’s Smart Focus feature for best focus. See MENU > SETUP > SMART FOCUS section for more information.

Am52RBack Box

DB60 GooseneckBracket

Use siliconeto maintainIP66 rating

3/4” RigidPipe

3/4” Electrical EMT Conduit Fitting

Use siliconeto maintainIP66 rating

Am52RBack Box

Am52 Series cameras can be wall-mounted with the use of i3’s gooseneck wall bracket (Part # DB60 /DB60B, Sold separately). Together with the optional DB60CPM/DB60CPMB bracket, DB60/DB60B gooseneck bracket has the capability of being corner- or pole-mounted.Follow the mounting instructions supplied with the DB60 / DB60B bracket.Attach the top conduit hole of the camera’s back box to the threaded end of the DB60/DB60B bracket and rotate clockwise to attach the two together. Use silicone sealer to maintain IP66 rating when installing outdoors.Complete installation as for Surface Mounting from Step #8 onwards.

PENDANT POLE MOUNTING

Use a 3/4” Electrical EMT Conduit Fitting with a rigid 3/4” pipe for this type of installation.Attach the top conduit hole of the camera’s back box to the threaded end of the 3/4” Electrical EMT Conduit Fitting and rotate clockwise to attach the two together.

Use silicone sealer to maintain IP66 rating when installing outdoors.Complete installation as for Surface Mounting from Step #8 onwards.

CAMERA MENUUse the camera’s on-board joystick to adjust camera settings.Use the button in the middle of the Joystick to access the camera OSD MENU and confirm selection. Move the Joystick in UP/DOWN/LEFT/RIGHT directions to navigate within camera menus.

UP

Press to access camera menu and to confirm selection.

INSTALLING THE CAMERA

Prepare the mounting surface.• Depending on the type of

installation, additional mounting accessories may need to be purchased.

• It is the installer’s responsibility to ensure that the mounting surface is suitable for the chosen installation method.

• Based on installation location and surface type, supplied screws and anchors may not be adequate. Mounting hardware is site-specific and may need to be supplied by the installer.

SURFACE MOUNTING1. Use the supplied security Torx key to loosen three

screws securing the dome bubble housing to camera module. Gently pull the dome bubble away from the main camera module.

2. Temporarily remove the camera liner/shroud for easier lens adjustment.

3. Depending on the type of installation and mounting surface, complete drilling 2-4 holes in the back box in preparation for the mounting.

4. Attach the supplied mounting template to the mounting surface.

5. Drill holes, as marked on the template and insert supplied anchors into the holes. The number and positioning of holes must match the ones pre-drilled on the back box in Step 4.

6. Drill the conduit hole for the camera cable, as marked on the template, if using the top conduit hole to route cables. Skip this step if using the side conduit hole.

7. Use three tapping screws provided to secure the camera’s back box to the prepared mounting surface.

8. Feed the camera cables through the selected conduit hole. Use silicone sealer around the chosen conduit hole to maintain IP66 rating when installing outdoors.

9. Use the supplied security Torx key to attach the camera module to the back box. Use three long machine-type screws pre-inserted into the camera module.

USER MANUAL

Page -3-

Am52 Series Analog Dome Camera

MENU > SETUP > WB (WHITE BALANCE)Set White Balance to ATW, AWC or MANUAL.• ATW (Auto Tracing White Balance): Adjusts white

balance automatically in accordance with the change of lighting environment.

• AWC>SET (Auto White Balance Control): Adjusts white balance based on a designated white object, such as a sheet of white paper or a gray scale chart. Frame the standard white object, then select the AWC>SET to set the camera’s white balance.

• MANUAL: Set BLUE and RED values from 1 to 100 manually, to adjust colour balance.

MENU > SETUP > DAY & NIGHTUnder DAY & NIGHT, set the camera to COLOR, B/W or EXT mode for Smart IR.• COLOR: Set the camera to COLOR mode to keep the camera permanently in the

daytime (colour image) mode.• B/W: Set the camera to B/W mode to keep the camera permanently in the nighttime

(black-and-white video image) mode.• EXT: Set the camera to EXT for Smart IR to automatically switch between Daytime

colour and night-time B/W modes based on the illumination conditions. Additionally, set the camera’s IR LED to ON to enable IR automatically when in night-time mode.

MENU > SETUP > NRThe Noise Reduction function removes image noise from static and moving video images. Spatial (2D NR) and Temporal (3D NR) Noise Reduction options are supported by your camera and can be combined.• 2D NR: Set to ON or OFF.

Spatial (2D NR) Noise Reduction analyzes single frames individually to distinguish pixels that likely represent noise. 2D NR does not produce motion blur.

• 3D NR: Set to ON or OFF. Temporal (3D NR) Noise Reduction analyzes frames in sequence to differentiate pixels that likely represent noise. 3D NR is very effective at reducing noise.• SMART NR: Set to ON or OFF

• SENSITIVITY: Set the value from 0 to 100.• LEVEL: Set 3D NR LEVEL value from 0 to 100.• START.AGC, END.AGC: Set the START and END AGC

values from 0 to 100 to define the threshold of the automatic gain control.

MENU > SETUP > SPECIALSPECIAL setup contains settings for CAMERA TITLE, D-EFFECT, PRIVACY, and DEFECT functions.• CAM TITLE: Enter and superimpose a descriptive camera

title onto the video feed.• D-EFFECT:

• FREEZE: Set to ON to permanently freeze the current live frame on the screen.

• MIRROR: This function flips the video image on the screen. Set MIRROR to OFF (keep image as is), MIRROR (flip horizontally), V-FLIP (flip vertically) or ROTATE (flip image both horizontally and vertically). Note: MIRROR function is disabled if FREEZE is ON.

• D-ZOOM: Set to ON to digitally zoom into the video image. This is a digital zoom function and not a true optical zoom. The final image is not enhanced by digital zoom - the number of pixels remains the same. Note: D-ZOOM function is disabled when SMART

MENU > SETUP Under the SETUP Menu, use the camera’s built-in Joystick to move around the menu tree and to select setting categories.

MENU > SETUP > SMART FOCUS Smart Focus feature allows for focusing precision during installation. After the camera is securely mounted, connect the service monitor to the 2-pin connector on the camera module. Adjust the Zoom lever until your desired field of view is achieved. Press the Joystick button to enter the camera’s OSD menu and select SMART FOCUS option. Blue numbers will be shown on the screen. Start adjusting the Focus lever until the numbers on screen are as close to 100 as possible. The higher the number, the better the focus.

MENU > SETUP > SCENEUnder SCENE, select INDOOR, OUTDOOR, INDOOR1 and LOW-LIGHT as the working environment. This scene selection adjusts the brightness of the video image to the pre-configured levels.

MENU > SETUP > LENS Your camera is equipped with a vari-focal 2.8-12mm @ F1.4 lens. Manually adjust the camera lens zoom and focus levers on the camera module. Loosen Zoom / Focus screws before adjustment and re-tighten them once the desired view/focus is achieved.

MENU > SETUP > EXPOSUREEXPOSURE setup contains settings for SHUTTER, AGC, SENS-UP, BRIGHTNESS, D-WDR, and DEFOG functions. • SHUTTER: Set camera shutter speed to AUTO,1/30,1/60,FLK

(Flickerless mode),1/240,1/480,1/1K,1/2K,1/5K,1/10K,1/50K.• AGC: Set the Automatic Gain Control value from 0 to 15.• SENS-UP: (Note: SENS-UP is disabled if AGC value is 0 or

when SHUTTER is set to anything other than AUTO or 1/30). SENS-UP function allows setting a slower shutter speed to let extra light into the camera for higher sensitivity in low-light conditions. SENS-UP can be set to OFF or AUTO. When in AUTO mode, SENS-UP can be set to: x2, x4, x6, x8, x10, x15, x20, x25, or x30.

• BRIGHTNESS: Set the video image brightness value from 1 to 100, where 100 represents the highest brightness setting.

• D-WDR: Digital Wide Dynamic Range prevents direct bright light from washing out the image. D-WDR can be set to ON or OFF. Important: True WDR can be configured under SETUP>BACKLIGHT>WDR section. On-board dip switch must be in the WDR mode.

• DEFOG: Digital DEFOG function uses built-in video processing algorithm to improve video appearance in foggy conditions. Set DEFOG function to ON or OFF. When enabled, DEFOG function allows setting area’s POSITION / SIZE and GRADATION.• POS/SIZE. By default, DEFOG area covers the entire screen. To re-size/re-position:

1. Press the Joystick button twice to first adjust the SIZE of the selected area. 2. Press and hold the Joystick UP/LEFT to reduce the height/width of the area. 3. Press the Joystick button to save changes and select AGAIN to return to the POSITION screen.

• 4. Move the joystick to reposition re-sized area on the screen. 5. Press the Joystick button twice to save changes and select RET to exit POS/SIZE DEFOG sub-menu.

• GRADATION. Set the GRADATION value to OFF, LOW, MIDDLE, or HIGH.• DEFAULT. Select DEFAULT to reset DEFOG settings back to factory defaults.

MENU > SETUP > BACKLIGHTBACKLIGHT setup can be set to OFF, WDR, BLC, or HSBLC. • WDR (Wide Dynamic Range):

Note: To enable WDR mode, camera’s CVBS/WDR

SPECIAL1. CAM TITLE OFF 2. D-EFFECT 3. PRIVACY OFF4. DEFECT 5. RETURN RET

MANUAL WB1. BLUE --|--502. RED --|--503. RETURN

3D NR1. SMART NR ON2. LEVEL ---|--803. START.AGC -|----104. END.AGC -|----105. RETURN RET

MENU > VIDEO OUT Under VIDEO OUT, set the camera video standard to NTSC or PAL.

MENU > LANGUAGE Under LANGUAGE, set the camera language to one of the avail. options, incl. English, French, etc.

EXPOSURE1. SHUTTER AUTO 2. AGC --|--153. SENS-UP OFF 4. BRIGHTNESS --|--60 5. D-WDR ON6. DEFOG OFF7. RETURN RET

WDR1. GAIN HIGH2. WDR BRIGHT --|--303. WDR OFFSET ---|-40 4. RETURN RET

• BLC (Backlight Compensation):• GAIN: Set the GAIN value to LOW, MIDDLE or HIGH.• AREA: To change BLC area’s position and size, follow instructions under

DEFOG POS/SIZE section above.• DEFAULT: Select DEFAULT to reset BLC settings back to factory defaults.

2D&3D NR1. 2DNR ON2. 3DNR ON3. RETURN RET

dipswitch must be in the WDR position.• GAIN: Set the GAIN value to LOW, MIDDLE or HIGH.• WDR BRIGHTNESS: Set the WDR BRIGHT value from 0 to 60.• WDR OFFSET: Set the WDR OFFSET value from 0 to 60.

• HSBLC (Highlight Suppression Backlight Compensation): HSBLC allows configuring up to 4 separate areas. Each AREA can be set to ON or OFF and each one can be re-sized and/or repositioned on the screen.

• SELECT: Select one of 4 available HSBLC areas.• DISPLAY: Set to ON to configure selected area’s

POSITION and SIZE. To change HSBLC area’s position and size, follow instructions under DEFOG POS/SIZE section.• LEVEL: Set the HSBLC LEVEL value from 0 to

100. • MODE: Set the HSBLC MODE to ALL Day or

NIGHT. • BLACK MASK: Set the BLACK MASK to ON or

OFF. • DEFAULT. Select DEFAULT to reset HSBLC

settings back to factory defaults.

D-EFFECT1. FREEZE OFF2. MIRROR V-FLIP3. D-ZOOM OFF4. SMART D-ZOOM OFF5. NEG.IMAGE OFF6. RETURN RET

MENU

VIDEO OUT SETUPLANGUAGE

COLOR

BLC

ATWSHUTTERINDOOR

HSBLC

AWC-SETAGC

MANUAL

OUTDOOR

MANUALSENS-UPINDOOR1

LOW-LIGHT

SCENE DAY&NIGHTBACKLIGHT WBEXPOSURELENS

2D NR

3D NR

NR

CAM TITLE

D-EFFECT

PRIVACY

DEFECT

SPECIAL

SHARPNESS

MONITOR

LSC

ADJUST RESET

BRIGHTNESS

SENSE-UP

B/W

EXT

EXIT

D-WDR

DEFOG

WDR

SMART FOCUS

HSBLC1. SELECT AREA12. DISPLAY ON3. LEVEL --|----204. MODE ALL DAY5. BLACK MASK ON6. DEFAULT7. RETURN RET

BLC1. GAIN HIGH2. AREA3. DEFAULT4. RETURN RET

OUTPUT MODE

USER MANUAL

i3 INTERNATIONAL INC. 1.866.840.0004www.i3international.com

Canada 780 Birchmount Road, Unit 16, Scarborough, ON, M1K 5H4

U.S.A. 4450 Witmer Industrial Estates Unit 4 Niagara Falls, NY 14305

Am52 Series Analog Dome Camera

Rev.

1611

23

Specifications Am52R / Am52RB (HD1080P Indoor/Outdoor Vandal Dome Camera)

Image System

Image Sensor 2MP CMOS Image SensorSignal System NTSC / PALEffective Pixels (HxV) 1944(H) x 1092(V)OSD YesAspect Ratio 4:3 / 16:9Optical SystemFocal Length (built-in lens) vari-focal, 2.8-12mmF-stop Range (F-number) F1.4Horizontal FOV (Field of View) 103° - 32.1°Day/Night ICRElectricDigital Noise Reduction (DNR) 2D / 3D

Wide Dynamic Range (WDR) True WDR (120dB) and Digital

Min. Illumination 0.001 Lux @ (F1.2, AGC ON), 0 Lux with IR 0.014 Lux @ (F1.4, AGC ON), 0 Lux with IR

S/N Ratio More than 62dB

Automatic Gain Control (AGC) Yes

White Balance ATW, AWC, Manual

Electric Shutter NTSC: 1/60 s to 1/50,000 s PAL: 1/50 s to 1/50,000 s

Video OutputStreams both outputs simultaneously. HD Video Output works only with i3’s HR16 encoder or standalone Veo17 DVR.

CVBS Output: 1 x 1Vp-p Compos-ite Output (75Ω/BNC)

HD Video Output: 1 x Analog HD output

Day/Night Mode Colour/BW/EXTOther Features

Privacy Mask On/Off, maximum 8 zonesOther Sharpness, Brightness, Digital

Zoom, Mirror, HSBLC, Defog, Smart Focus

MechanismAngle Adjustment Pan: 0 - 355°, Tilt: 0 - 75°,

Rotation: 0 - 355°

Dimensions Ø 147mm x 140mm (H) / Ø 5¾“ x 5½” (H)

Weight 0.9 kg (1.98 lb)

Protection Class FCC, CE, IP66, IK8, UL

IR

IR Distance up to 40 meters (131 feet)

Power Supply

Power Requirement DC 12V & AC 24V

Power Consumption Max. 6W

EnvironmentOperating Temperature -30 °C - 60 °C (-22 °F - 140 °F)

Operating Humidity 90% or less (non-condensing)

Warranty

Standard Warranty i3 Superior 3 year warranty

D-ZOOM is ON.• D-ZOOM: Set the digital zoom to one of the available presets: x2.0,

x2.1 - x3.9, x4.0 - x62.0.• PAN&TILT: Move the Joystick in UP/DOWN/LEFT/RIGHT directions to

reposition the zoomed area on the screen.• DEFAULT: Select DEFAULT to reset D-ZOOM settings back to factory

defaults.• SMART D-ZOOM: The camera can be programmed to zoom into one of two pre-configured

areas. Note: SMART D-ZOOM function is disabled when D-ZOOM is ON.• SELECT: Select AREA1 or AREA2.• DISPLAY: Set selected AREA to ON to enable. Move the Joystick in

UP/DOWN/LEFT/RIGHT directions to reposition selected area on the screen. Press the Joystick button to save the new area position.

• D-ZOOM: Set the digital zoom level to one of the presets: x2.0, x2.1 - x3.9, x4.0 - x62.0. Note: As the D-ZOOM number increases, the physical area on screen will become smaller. You may want to re-position the adjusted area on the screen after changing D-ZOOM setting.

• DEFAULT: Select DEFAULT to reset SMART D-ZOOM settings to factory defaults.• NEG IMAGE: Set the NEG IMAGE to ON to show a negative of the camera’s video image (darkest

and lightest areas of the image appear reversed).• PRIVACY: Set up to 8 separate privacy (masking) areas to block off areas of the camera’s field of

view. IMPORTANT: Video hidden behind the set Masking Area will be permanently lost.• SELECT: Select one of 8 available privacy area shapes (AREA1-AREA8) that best suits your

needs.• DISPLAY: Select the type of image that will block off the area: OFF (hide

selected AREA), COLOR (solid colour), INV. (Inverse colours inside the selected area/negative image), or MOSAIC (apply blurring effect to the live image). To adjust area’s position or shape/size, select DISPLAY TYPE and press the Joystick button. Continue pressing the Joystick button to switch between POSITION/TOP LEFT/TOP RIGHT/BOTTOM LEFT/BOTTOM RIGHT options. The area’s size is adjusted by re-positioning each corner of the selected shape. Use the Joystick to move each corner on the screen or to reposition adjusted privacy area.

• COLOR: Set the COLOR value from 0 to 15 to use one of the 16 available colours.• TRANS: Set the area Transparency value from 0 to 3. (0=transparent, 3=opaque).• DEFAULT: Select DEFAULT to reset PRIVACY settings back to factory defaults.

• DEFECT: An image sensor may have permanent bright or dark pixels, called dead pixels, due to physical defects. These dead pixels are much brighter/darker than their neighboring pixels and will create noise on the video image. DPC (Dead Pixel Correction) is a function that is designed to remove these dead pixels dynamically from the live video (LIVE DPC) or based on saved predefined pixel locations (STATIC DPC).• LIVE DPC: Set LIVE DPC function to OFF, AUTO, or ON. When set to ON, LIVE DPC LEVEL can be

configured.• LEVEL: When LIVE DPC is set to ON, set the LEVEL value from 0 to

100.• STATIC DPC: Set to ON to execute STATIC DPC function to locate and

record the positions of all dead pixels on the image sensor (CMOS).• START: Cover the lens or close the iris to prevent light from entering

the lens and press the Joystick key to launch STATIC DPC function.• LEVEL: Set the LEVEL value from 0 to 60.• SENS-UP: Set the SENS-UP value to: x2, x4, x6, x8, x10, x15, x20, x25, or x30.• AGC: Set the AGC value from 0 to 8.

• OUTPUT MODE: Select the video aspect ratio output: either 4:3 or 16:9 aspect ratios.

MENU > SETUP > ADJUSTADJUST setup contains settings for SHARPNESS, MONITOR, and LSC functions.• SHARPNESS: Set image sharpness value from 0 to 15.• MONITOR: Choose the appropriate monitor type: LCD or CRT.

• CRT: Configure BLACK LEVEL, BLUE GAIN and RED GAIN. Values range from -30 to +30.• LCD: Configure GAMMA, BLUE GAIN and RED GAIN.

• GAMMA level options: AUTO, USER, USER+Y, 0.45-1.00 (in 0.05 increments).

• BLUE GAIN: Set BLUE GAIN value from 0 to 100.• RED GAIN: Set RED GAIN value from 0 to 100.

• LSC: Set LSC function to ON or OFF. Lens Shading Correction provides brightness compensation for scenes where image appears bright in the centre and darker around the edges. LSC equalizes image brightness to the edge of the field-of-view.

MENU > SETUP > RESET, EXITSelect RESET to reset all camera settings to the factory default.Select EXIT to exit the camera OSD menu.

PRIVACY1. SELECT AREA 12. DISPLAY MOSAIC3. COLOR 104. TRANS 15. DEFAULT 6. RETURN RET

SMART D-ZOOM1. SELECT AREA 12. DISPLAY ON3. D-ZOOM x 2.74. DEFAULT5. RETURN RET

DEFECT1. LIVE DPC AUTO2. STATIC DPC OFF3. RETURN RET

ADJUST1. SHARPNESS ----|152. MONITOR LCD3. LSC OFF4. RETURN RET

STATIC DPC1. START 2. LEVEL ----|603. SENS-UP x24. AGC -----|85. RETURN RET

D-ZOOM1. D-ZOOM x 2.52. PAN&TILT 3. DEFAULT 4. RETURN RET