Senior Project Times New Roman 20 Bold Times New Roman 24 ... · College of Engineering Electrical...
17
Kingdom of Saudi Arabia Ministry of Higher Education Taif University College of Engineering Electrical Engineering Department Senior Project Title of the Graduation Project by AAAAAAA [ID] BBBBBBBB [ID] CCCCCCC [ID] DDDDDDD [ID] EEEEEEE [ID] FFFFFFFFFF [ID] Under the Supervision of Prof. Abcdefg Dr. Abcdefg Spring 2018 (May. 2018 AD, Ramadan 1439 AH) Times New Roman 20 Bold Times New Roman 24 Times New Roman 16 Italic Times New Roman 18 Times New Roman 16 Italic Times New Roman 16 Times New Roman 16
Transcript of Senior Project Times New Roman 20 Bold Times New Roman 24 ... · College of Engineering Electrical...
Kingdom of Saudi Arabia Ministry of Higher Education
Taif University College of Engineering
Electrical Engineering Department
Senior Project
Title of the Graduation Project
by
AAAAAAA [ID] BBBBBBBB [ID]
CCCCCCC [ID] DDDDDDD [ID]
EEEEEEE [ID] FFFFFFFFFF [ID]
Under the Supervision of
Prof. Abcdefg
Dr. Abcdefg
Spring 2018
(May. 2018 AD, Ramadan 1439 AH)
Times New Roman 20 Bold
Times New Roman 24
Times New Roman 16 Italic
Tim
es N
ew R
om
an
18
Times New Roman 16 Italic
Times New Roman 16
Times New Roman 16
Title of the Graduation Project 1 | P a g e
Table of Contents
Subject Page
EXAMINERS COMMITTEE………………………………. 00
ACKNOWLEDGEMENT ……………………………………. 00
ABSTRACT ………………………………………………….. 00
Problem Description ………………………………..……….... 00
List of Figures ………………………………………………… 00
List of Tables (if any) ………………………………………… 00
Nomenclatures ………………………………………………... 00
1. INTRODUCTION ………………….......................................... 00
1.1. Xxxxxxxxxx ……………………......................... 00
1.1.1. Xxxxxxxxxx ……………………......................... 00
1.1.2. Xxxxxxxxxx ……………………......................... 00
1.2. Xxxxxxxxxx ……………………......................... 00
1.2.1. Xxxxxxxxxx ……………………......................... 00
1.2.2. Xxxxxxxxxx ……………………......................... 00
2. EXPERIMENTAL WORK…………………………………… 00
2.1. Preliminary Experiments…………......................... 00
2.1.1. Xxxxxxxxxx ……………………......................... 00
2.1.2. Xxxxxxxxxx ……………………......................... 00
2.2. Final Experiments………………......................... 00
2.2.1. Xxxxxxxxxx ……………………......................... 00
2.2.2. Xxxxxxxxxx ……………………......................... 00
3. RESULTS AND DISCUSSION ……………………………….. 00
4. CONCLUSIONS AND RECOMMENDATIONS …………. 00
REFERENCES ………………………………………….…... 00
APPENDICES
A. CONSTRAINTS
B. ENGINEERING STANDARDS
C. CHECK LIST
هالحظة هاهة: بالنسبة لحجن ونوع الخط الوستخدم يوكن تحديده هن خالل النقر على الكلوة فى باقى التقرير
.1.5األسطر والوسافة بين 14النص الرئيسي يكتب بخط بحجن كوا هو هوضح فى هذه الصفحة.
Title of the Graduation Project 2 | P a g e
ACKNOWLEDGEMENTS
Title of the Graduation Project 3 | P a g e
ABSTRACT
Title of the Graduation Project 4 | P a g e
Problem Description
Title of the Graduation Project 5 | P a g e
List of Figures
Fig. 1 Description of how to write figure caption.
Title of the Graduation Project 6 | P a g e
List of Tables (if any)
Table 1 This is how to write table caption.
Title of the Graduation Project 7 | P a g e
Nomenclatures
Title of the Graduation Project 8 | P a g e
1. INTRODUCTION (Literature Review)
Title of the Graduation Project 9 | P a g e
2. EXPERIMENTALWORK (OR) SIMULATION STUDIES
Figures should be centered with figure caption as shown below.
Fig. 1 Description of how to write figure caption.
Tables should be centered with table caption as shown below.
Table 1 This is how to write table caption.
Title of the Graduation Project 10 | P a g e
Title of the Graduation Project 11 | P a g e
3. RESULTS AND DISCUSSION
Title of the Graduation Project 12 | P a g e
4. CONCLUSIONS AND RECOMMENDATIONS
Title of the Graduation Project 13 | P a g e
REFERNCES
1. F. B. Incropera and D. P. Dewitt, Fundamentals of Heat and Mass Transfer,
Fifth Edition, John Wiley & Sons, 2006.
2. P. Srithananan, P. Kaewtatip, V. Uthaisangsuk, Micromechanics-based
modeling of stress–strain and fracture behavior of heat-treated boron steels
for hot stamping process, Materials Science & Engineering A, Vol. 667, pp.
61-76, June 2016.
3. A. Fotouh, R. El-Hebeary, M. El-Shennawy, David Tulloch, Jason Davio and
Rob Reid, Integrated Experimental Procedures Assessing Hydrogen Induced
Cracking Susceptibility, ASME 2015 Pressure Vessels and Piping
Conference PVP, Boston, Massachusetts, USA, July 19-23, 2015.
4. Standard Test Methods for Notched Bar Impact Testing of Metallic
Materials, ASTM E23-12c, ASTM International, West Conshohocken, PA,
2012.
5. Hibbitt, Karlsson & Sorensen. Inc., ABAQUS, Version 5.5, 1995.
6. http://www.sciencedirect.com/science/article/pii/S0921509316304609
BOOKمثال:
JOURNAL PAPERمثال:
CONFERENCE PAPERمثال:
ENGINEERING STANDARDمثال:
INTERNET SITEمثال:
Title of the Graduation Project 14 | P a g e
APPENDICES
A. CONSTRAINTS
Title of the Graduation Project 15 | P a g e
B. ENGINEERING STANDARDS
Title of the Graduation Project 16 | P a g e
C. CHECK LIST
