SECTION DIRECTORY - Construction
Transcript of SECTION DIRECTORY - Construction
CM-1
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
Brand Directory
Architect Series ...................................................................................................................................................................CM-1
General InformationBrand Summary ..................................................................................................................................................................CM-2
Product Selection Guide
Size and Performance Data .....................................................................................................................................CM-3
Features and Options ..............................................................................................................................................CM-4
Glazing Performance ..........................................................................................................................................................CM-5
Sound Transmission Class and Outdoor-Indoor Transmission Class ........................................................................CM-22
Combination Assemblies.................................................................................................................................................CM-23
Architect SeriesGrille Types
Grille Profiles ...........................................................................................................................................................CM-24
Grille Pattern ...........................................................................................................................................................CM-25
HurricaneShield® Impact-Resistant Casement Windows ............................................................................................CM-26
Custom Shapes .................................................................................................................................................................CM-27
Size Tables and Special Sizes—Clad and Wood ............................................................................................................CM-32
Design Data—Vent and Fixed ..........................................................................................................................................CM-35
Detailed Product Descriptions ........................................................................................................................................CM-37
Unit Sections / Typical Joining Mullions
Clad ..........................................................................................................................................................................CM-39
Wood .......................................................................................................................................................................CM-42
Designer SeriesGrille Types
Grille Profiles and Patterns ....................................................................................................................................CM-44
Size Tables and Special Sizes—Clad ...............................................................................................................................CM-45
Design Data .......................................................................................................................................................................CM-47
Shade Handing Guide .....................................................................................................................................................CM-49
Detailed Product Descriptions ........................................................................................................................................CM-50
Pella ProLineGrille Types
Grille Profiles and Patterns ....................................................................................................................................CM-53
Size Tables—Clad ...............................................................................................................................................................CM-54
Design Data .......................................................................................................................................................................CM-55
Detailed Product Descriptions ........................................................................................................................................CM-57
Unit Sections / Typical Joining Mullions .........................................................................................................................CM-58
SECTION DIRECTORY
General Notes:Specifications subject to change without notice. Go to www.PellaADM.com for most current technical data.
For complete CSI Format Specifications browse online at www.PellaADM.com.
Abbreviations:P = Pending. Data not available at time of publication. Go to www.PellaADM.com for most current technical data.
HGP = Hinged Glass Panel
PVB = Polyvinyl butyral. This is a laminate material used in Pella HurricaneShield® glazing and is the same material traditionally used in car windshield applications.
SGP = SentryGlas® Plus from DuPont®. This is a stiffer laminate material which is optional in select HurricaneShield impact-resistant glazing products. SentryGlas Plus and DuPont are registered trademarks of E. I. DuPont De Nemours & Company.
HA = High Altitude Glass. See Wood / Clad Overview section for more information.
CM-2
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
BRAND SUMMARY
Casement Windows are traditional in every
detail – with all the Pella innovations you demand. Pella's EnduraGuard
protection formula, together with our immersion-treatment method,
provides strong protection on every exterior wood surface of your
windows and patio doors. This innovation provides advanced
protection against the effects of moisture, decay, stains from mold and
mildew – as well as termite damage. The exterior of the wood windows
are protected by Pella’s low-maintenance EnduraClad® protective finish,
or EnduraClad® Plus protective finish. We maintain our high standard
of energy efficiency with weatherstripping at the sides of sash, and full
perimeter weatherstripping to reduce air infiltration. Pella maintains its
high standards by taking the time to test virtually every vent unit for air
infiltration, so you know you’re getting a quality product.
Midtown Community Elementary School, Neptune Township, NJ, SSP Architectural Group
ARCHITECT SERIES®
• A wide range of glazing options as well as HurricaneShield® impact-resistant Casements
• Divided light options available in Integral Light Technology® grilles, Grilles-Between-the-Glass or wood removable grilles in standard and custom patterns
• EnduraClad® protective finish in standard and feature colors plus nearly unlimited custom colors
• EnduraClad Plus protective finish in standard and feature colors plus nearly unlimited custom colors
• InView™ screens or Vivid View® screens or Rolscreen
DESIGNER SERIES®
• Simplicity of insulated glass with the distinction of exclusive options
• Snap-in between-glass shades, and blinds as well as removable between-glass grilles—the ultimate solution for dressing a window
• EnduraClad aluminum-clad exteriors in standard and feature colors plus nearly unlimited custom colors
• InView™ screens or Vivid View® screens or Rolscreen
Triple-Pane Glazing System
PELLA® PROLINE 450
• EnduraClad aluminum clad exteriors in standard and feature colors
• Removable room side grilles, Grilles-Between-the-Glass, Simulated-Divided- Lite grilles
• Prefinished stain, prefinished White, Bright White, Linen White or factory primed interiors
• Stainless steel operating arms and hinges resist rust and corrosion
• InView™ screens or Vivid View® screens
CM-3
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
PRODUCT SELECTION GUIDE
Size and Performance Data
(—) = Not Applicable
(1) Maximum performance for single unit when glazed with the appropriate glass thickness. See Design Data pages in this section for specific product performance class and grade values. Values shown are for standard and special sizes; Custom shapes and sizes may not have the same values. Contact your local sales representative for complete information.
(2) The higher the level, the greater the product’s ability to resist forced entry.
ARCHITECT SERIES
DESIGNER SERIES
PELLA PROLINE 450
Clad Wood Clad Clad
SIZES
Standard Vent / Fixed Sizes l l l l
Standard Fixed Companion Sizes l l l l
Standard Quarter and Half Circle l l — —
Standard Elliptical l l — —
Standard Springline l l — —
Standard Full Circle l l — —
Standard Oval l l — —
Arch Head Sizes—Full and Partial l l — —
Transom Sizes l l l l
Egress Sizes l l l l
Special Sizes Available l l l l
Custom Shapes and Sizes l l — —
PERFORMANCE 1
Meets or Exceeds AAMA / WDMA Ratings CW30-CW50
Hallmark Certified
CW30-CW50Hallmark Certified
R20-R50 Hallmark Certified
R30-R50Hallmark Certified
Air Infiltration (cfm / ft 2 of frame @ 1.57 psf wind pressure)
0.05 0.05 0.05 0.05
Water Resistance 7.5 psf 7.5 psf 7.5 – 10.5 psf 7.5 psf
Design Pressure 50 psf 50 psf 50 psf 30-50 psf
With HurricaneShield® Impact-Resistant GlassC-R/CW75 - C-R/CW85
Hallmark Certified
C-CW60Hallmark Certified
— —
OTHER PERFORMANCE CRITERIA
Forced Entry Resistance Level
(Minimum Security Grade) 210 10 10 10
Maximum Operating Force (lb)
Initiate Motion / Maintain Motion15 / 6 15 / 6 15 / 6 15 / 6
All vent sizes are available with left- or right-hand hinging, as viewed from the exterior.
Left Right
CM-4
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
PRODUCT SELECTION GUIDE
Features and Options
S = Standard; O = Optional; (—) = Not Available
(1) Contact your local Pella sales representative for current designs and color options.
(2) Unit height determines availability.
(3) For detailed information see between-the-glass options in the Overview section.
(4) See the Clad/Wood Overview section for feature color options. Popular White, Hartford Green, Black and Brick Red are the only feature color options available for Pella ProLine. Morning Sky Gray and Portobello in Spring 2015.
(5) Available with Low-E argon-insulated glass only.
(6) Pine is standard exterior for wood exterior unit. Mahogany is an option for wood exterior.
(7) Not available on mahogany, alder and douglas fir interiors.
(8) Only available win Architect Series products with triple glazing. Not available with high altitude glazing.
ARCHITECT SERIES
DE
SIG
NE
R
SE
RIE
S
PE
LLA
P
RO
LIN
E
Clad Wood
HARDWARE
Champagne, White or Brown S S S S
Bright Brass, Satin Nickel or Oil-Rubbed Bronze
O O O O
Sash Locks
SureLock® System S S S S
Unison Lock System 2 S S S S
SCREENS
InView™ screens O O O O
Vivid View® screens O O O O
Rolscreen® Retractable screens O O O —
GRILLES
Integral Light Technology®
Traditional, Prairie, Top Row, Cross, New England, Victorian, Simulated French, Custom
O O — —
Removable Pine Wood Interior
Traditional O O — O
Prairie, Top Row, Cross, New England, Victorian, Custom
O O — —
Removable Between-Glass
Traditional, Prairie, Top Row, Cross, New England, Custom
— — O —
Gril les-Between-the-Glass
Traditional, Prairie, Cross, Top Row 1, Custom-Equally Divided
O O — O
Simulated Divided Light 5 with Optional Spacer
Traditional, Prairie, Cross, Top Row, Custom-Equally Divided
— — — O
WINDOW FASHIONS 3
Cellular Fabric Shades 1
Between-Glass Bottom-Up — — O —
Between-Glass Top-Down — — O —
Slimshade ® Bl inds 1
Between-Glass Bottom-Up — — O —
Between-Glass Tilt-Only — — O —
ARCHITECT SERIES
DE
SIG
NE
R
SE
RIE
S
PE
LLA
P
RO
LIN
E
Clad Wood
GLAZING
Glazing Type
Dual-Pane Insulating Glass S S — S
Triple-Pane Insulating Glass O O — —
Designer Series® triple-pane glazing — — S —
Insulated Glass Options/Low-E Types
Advanced Low-E S S S S
SunDefense™ Low-E O O O O
AdvancedComfort Low-E O O O O
NaturalSun Low-E O O O OInsulating Glass with Clear Hinged Glass Panel
— — O —
Clear (no Low-E coating) O O O —
Additional Glass Options
Annealed Glass S S S S
Tempered Glass O O O O
Obscure Glass 1 O O O O
Tinted Glass (Bronze, Gray and Green) O O O —
Non-Impact Laminated Single-Pane Glass O O — —Non-Impact Laminated Dual-Pane Insulating Glass
O O O —
Hurricaneshield® Impact Resistant Products with Laminated Single-Pane Glass
O O — —
Hurricaneshield® Impact Resistant Products with Laminated Dual-Pane 11/16" Insulating Glass
O O — —
Gas Fi l l/High Alt i tude
Argon S S S S
Krypton8 O O — —
High altitude O O O O
High altitude with argon O5 O — —
EXTERIOR
EnduraClad® protective finish S — S S
EnduraClad Plus protective finish O — O —
Primed Pine Wood Exterior — S — —
Unfinished Mahogany Wood Exterior — O — —
Cladding Colors
White, Tan, Putty or Brown S — S S
23 Feature Colors 4 O — O O
Custom Colors 1 O — O —
INTERIOR
Unfinished Wood S S S S
Factory primed O O O O
Factory prefinished paint 7 O 6 O 6 O O
Factory prefinished stain 1 O O O O
WOOD TYPES
Pine S6 S S S
Mahogany, Alder, Douglas Fir O6 O — —
CM-5
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad Wood Vent
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
VENT N NC SC S 1 2 311/16" Clear IG PEL-N-11-09073-00001 2.5 2.5 air 0.44 0.55 57 44
with grilles-between-the-glass PEL-N-11-09695-00001 0.44 0.50 52 44
with integral grilles PEL-N-11-09283-00001 0.44 0.50 52 44
11/16" Clear IG PEL-N-11-09074-00001 3 3 air 0.44 0.54 56 44
with grilles-between-the-glass PEL-N-11-09696-00001 0.44 0.49 51 44
with integral grilles PEL-N-11-09284-00001 0.44 0.49 51 44
11/16" Advanced Low-E IG PEL-N-11-09031-00001 2.5 2.5 argon 0.28 0.26 48 61 20
with grilles-between-the-glass PEL-N-11-09653-00001 0.28 0.24 44 61 19
with integral grilles PEL-N-11-09241-00001 0.29 0.24 44 61
11/16" Advanced Low-E IG PEL-N-11-09032-00001 3 3 argon 0.28 0.26 48 60 20
with grilles-between-the-glass PEL-N-11-09654-00001 0.28 0.24 43 60 19
with integral grilles PEL-N-11-09242-00001 0.29 0.24 43 61
11/16" SunDefense™ Low-E IG PEL-N-11-09044-00001 2.5 2.5 argon 0.28 0.19 45 62 16
with grilles-between-the-glass PEL-N-11-09666-00001 0.28 0.18 41 62
with integral grilles PEL-N-11-09254-00001 0.29 0.18 41 62
11/16" SunDefense™ Low-E IG PEL-N-11-09045-00001 3 3 argon 0.28 0.19 44 61 16
with grilles-between-the-glass PEL-N-11-09667-00001 0.28 0.18 40 61
with integral grilles PEL-N-11-09255-00001 0.29 0.18 40 61
11/16" AdvancedComfort Low-E IG PEL-N-11-10701-00001 2.5 2.5 argon 0.25 0.26 47 49 23
with grilles-between-the-glass PEL-N-11-10687-00001 0.25 0.23 43 49 22
with integral grilles PEL-N-11-10659-00001 0.25 0.23 43 49 22
11/16" AdvancedComfort Low-E IG PEL-N-11-10646-00001 3 3 argon 0.25 0.25 47 48 23
with grilles-between-the-glass PEL-N-11-10688-00001 0.25 0.23 42 48 22
with integral grilles PEL-N-11-10660-00001 0.26 0.23 42 48 20
11/16" NaturalSun Low-E IG PEL-N-11-09002-00001 2.5 2.5 argon 0.29 0.48 55 61 31
with grilles-between-the-glass PEL-N-11-09624-00001 0.29 0.44 50 61 29
with integral grilles PEL-N-11-09212-00001 0.30 0.44 50 61 28
11/16" NaturalSun Low-E IG PEL-N-11-09003-00001 3 3 argon 0.29 0.48 54 60 31
with grilles-between-the-glass PEL-N-11-09625-00001 0.29 0.43 49 60 28
with integral grilles PEL-N-11-09213-00001 0.30 0.43 49 60 27
TINTED GLAZING11/16" Bronze Advanced Low-E IG PEL-N-11-08989-00001 5 3 argon 0.29 0.23 31 60
with grilles-between-the-glass PEL-N-11-09611-00001 0.30 0.21 28 60
with integral grilles PEL-N-11-09199-00001 0.30 0.21 28 60
11/16" Gray Advanced Low-E IG PEL-N-11-09015-00001 5 3 argon 0.29 0.21 27 60
with grilles-between-the-glass PEL-N-11-09637-00001 0.30 0.19 24 60
with integral grilles PEL-N-11-09225-00001 0.30 0.19 24 60
11/16" Green Advanced Low-E IG PEL-N-11-09022-00001 5 3 argon 0.29 0.23 38 60
with grilles-between-the-glass PEL-N-11-09644-00001 0.30 0.21 34 60
with integral grilles PEL-N-11-09232-00001 0.30 0.21 34 60
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-6
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad Wood Vent
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
HIGH ALTITUDE GLAZING N NC SC S 1 2 311/16" Advanced Low-E IG PEL-N-11-09108-00001 2.5 2.5 air 0.31 0.26 48 58
with grilles-between-the-glass PEL-N-11-09730-00001 0.31 0.24 44 58
with integral grilles PEL-N-11-09318-00001 0.32 0.24 44 58
11/16" Advanced Low-E IG PEL-N-11-09109-00001 3 3 air 0.32 0.26 48 57
with grilles-between-the-glass PEL-N-11-09731-00001 0.32 0.24 43 57
with integral grilles PEL-N-11-09319-00001 0.32 0.24 43 57
11/16" SunDefense Low-E IG PEL-N-11-09121-00001 2.5 2.5 air 0.31 0.20 45 58
with grilles-between-the-glass PEL-N-11-09743-00001 0.31 0.18 41 58
with integral grilles PEL-N-11-09331-00001 0.32 0.18 41 58
11/16" SunDefense Low-E IG PEL-N-11-09122-00001 3 3 air 0.31 0.20 44 57
with grilles-between-the-glass PEL-N-11-09744-00001 0.31 0.18 40 57
with integral grilles PEL-N-11-09332-00001 0.32 0.18 40 57
11/16" AdvancedComfort Low-E IG PEL-N-11-10652-00001 2.5 2.5 air 0.27 0.26 47 45 21
with grilles-between-the-glass PEL-N-11-10694-00001 0.27 0.23 43 45 19
with integral grilles PEL-N-11-10666-00001 0.28 0.23 43 45 18
11/16" AdvancedComfort Low-E IG PEL-N-11-10653-00001 3 3 air 0.27 0.26 47 44 21
with grilles-between-the-glass PEL-N-11-10695-00001 0.27 0.23 42 44 19
with integral grilles PEL-N-11-10667-00001 0.28 0.23 42 44 18
11/16" NaturalSun Low-E IG PEL-N-11-09079-00001 2.5 2.5 air 0.32 0.48 55 57 27
with grilles-between-the-glass PEL-N-11-09701-00001 0.32 0.44 50 57 25
with integral grilles PEL-N-11-09289-00001 0.33 0.44 50 57
11/16" NaturalSun Low-E IG PEL-N-11-09080-00001 3 3 air 0.32 0.47 54 56 27
with grilles-between-the-glass PEL-N-11-09702-00001 0.32 0.43 49 56 25
with integral grilles PEL-N-11-09290-00001 0.33 0.43 49 56
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-7
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad Wood Triple-Pane Glazing
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Mid. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
VENT N NC SC S 1 2 31" Advanced Low-E IG PEL-N-11-09149-00001 3 3 3 argon 0.22 0.24 42 70 26
with grilles-between-the-glass PEL-N-11-09771-00001 0.22 0.22 38 70 25
with integral grilles PEL-N-11-10829-00001 0.23 0.22 38 70 24
1" Advanced Low-E IG PEL-N-11-10789-00001 3 3 3 Krypton 0.19 0.23 42 74 29
with grilles-between-the-glass PEL-N-11-10790-00001 0.19 0.21 38 74 28
with integral grilles PEL-N-11-10791-00001 0.20 0.21 38 74 27
1" SunDefense™ Low-E IG PEL-N-11-09156-00001 3 3 3 argon 0.22 0.18 39 70 23
with grilles-between-the-glass PEL-N-11-09778-00001 0.22 0.16 35 70 21
with integral grilles PEL-N-11-10837-00001 0.23 0.16 35 70 20
1" SunDefense™ Low-E IG PEL-N-11-10805-00001 3 3 3 Krypton 0.19 0.17 39 74 26
with grilles-between-the-glass PEL-N-11-10806-00001 0.19 0.16 35 74 25
with integral grilles PEL-N-11-10807-00001 0.20 0.16 35 74 24
1" NaturalSun Low-E IG PEL-N-11-09144-00001 3 3 3 argon 0.22 0.39 48 69 35
with grilles-between-the-glass PEL-N-11-09766-00001 0.23 0.36 43 69 32
with integral grilles PEL-N-11-10821-00001 0.23 0.36 43 69 32
1" NaturalSun Low-E IG PEL-N-11-10773-00001 3 3 3 Krypton 0.19 0.39 48 74 38
with grilles-between-the-glass PEL-N-11-10774-00001 0.19 0.36 43 74 37
with integral grilles PEL-N-11-10775-00001 0.20 0.36 43 74 35
HIGH ALTITUDE GLAZING1" Advanced Low-E IG PEL-N-11-09165-00001 3 3 3 air 0.25 0.24 42 66 22
with grilles-between-the-glass PEL-N-11-09787-00001 0.26 0.22 38 65 20
with integral grilles PEL-N-11-10853-00001 0.26 0.22 38 65 20
1" SunDefense Low-E IG PEL-N-11-09172-00001 3 3 3 air 0.25 0.18 39 66 19
with grilles-between-the-glass PEL-N-11-09794-00001 0.26 0.16 35 66 16
with integral grilles PEL-N-11-10861-00001 0.26 0.16 35 66 16
1" NaturalSun Low-E IG PEL-N-11-09160-00001 3 3 3 air 0.26 0.39 48 65 30
with grilles-between-the-glass PEL-N-11-09782-00001 0.26 0.35 43 65 27
with integral grilles PEL-N-11-10845-00001 0.27 0.35 43 65 26
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-8
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad Wood Fixed
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
FIXED N NC SC S 1 2 311/16" Clear IG PEL-N-1-17120-00001 2.5 2.5 air 0.45 0.63 66 45
with grilles-between-the-glass PEL-N-1-17742-00001 0.45 0.57 59 45
with integral grilles PEL-N-1-17330-00001 0.45 0.57 59 45
11/16" Clear IG PEL-N-1-17121-00001 3 3 air 0.46 0.62 65 44
with grilles-between-the-glass PEL-N-1-17743-00001 0.46 0.56 58 44
with integral grilles PEL-N-1-17331-00001 0.46 0.56 58 44
11/16" Advanced Low-E IG PEL-N-1-17078-00001 2.5 2.5 argon 0.27 0.30 56 61 23
with grilles-between-the-glass PEL-N-1-17700-00001 0.27 0.27 50 61 22
with integral grilles PEL-N-1-17288-00001 0.28 0.27 50 61 20
11/16" Advanced Low-E IG PEL-N-1-17079-00001 3 3 argon 0.27 0.30 56 60 23
with grilles-between-the-glass PEL-N-1-17701-00001 0.27 0.27 50 60 22
with integral grilles PEL-N-1-17289-00001 0.28 0.27 50 60 20
11/16" SunDefense™ Low-E IG PEL-N-1-17091-00001 2.5 2.5 argon 0.27 0.22 52 62 19
with grilles-between-the-glass PEL-N-1-17713-00001 0.27 0.20 46 62 17
with integral grilles PEL-N-1-17301-00001 0.27 0.20 46 62 17
11/16" SunDefense™ Low-E IG PEL-N-1-17092-00001 3 3 argon 0.27 0.22 51 61 19
with grilles-between-the-glass PEL-N-1-17714-00001 0.27 0.20 46 61 17
with integral grilles PEL-N-1-17302-00001 0.27 0.20 46 61 17
11/16" AdvancedComfort Low-E IG PEL-N-1-20356-00001 2.5 2.5 argon 0.23 0.29 54 48 28
with grilles-between-the-glass PEL-N-1-20398-00001 0.23 0.26 49 49 26
with integral grilles PEL-N-1-20370-00001 0.24 0.26 59 49 25
11/16" AdvancedComfort Low-E IG PEL-N-1-20357-00001 3 3 argon 0.23 0.29 54 48 28
with grilles-between-the-glass PEL-N-1-20399-00001 0.23 0.26 49 48 26
with integral grilles PEL-N-1-20371-00001 0.24 0.26 49 48 25
11/16" NaturalSun Low-E IG PEL-N-1-17049-00001 2.5 2.5 argon 0.28 0.56 64 61 37
with grilles-between-the-glass PEL-N-1-17671-00001 0.28 0.50 57 61 34
with integral grilles PEL-N-1-17259-00001 0.29 0.50 57 61 32
11/16" NaturalSun Low-E IG PEL-N-1-17050-00001 3 3 argon 0.28 0.55 63 60 36
with grilles-between-the-glass PEL-N-1-17672-00001 0.28 0.49 56 60 33
with integral grilles PEL-N-1-17260-00001 0.29 0.49 56 60 32
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-9
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad Wood Fixed
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
TINTED GLAZING N NC SC S 1 2 311/16" Bronze Advanced Low-E PEL-N-1-17036-00001 5 3 argon 0.28 0.26 36 60 20
with grilles-between-the-glass PEL-N-1-17658-00001 0.29 0.24 32 60
with integral grilles PEL-N-1-17246-00001 0.29 0.24 32 60
11/16" Gray Advanced Low-E IG PEL-N-1-17062-00001 5 3 argon 0.28 0.24 31 60 19
with grilles-between-the-glass PEL-N-1-17684-00001 0.29 0.22 28 60
with integral grilles PEL-N-1-17272-00001 0.29 0.22 28 60
11/16" Green Advanced Low-E IG PEL-N-1-17069-00001 5 3 argon 0.28 0.26 44 60 20
with grilles-between-the-glass PEL-N-1-17691-00001 0.29 0.23 39 60
with integral grilles PEL-N-1-17279-00001 0.29 0.23 39 60
HIGH ALTITUDE GLAZING11/16" Advanced Low-E IG PEL-N-1-17155-00001 2.5 2.5 air 0.31 0.30 56 57
with grilles-between-the-glass PEL-N-1-17777-00001 0.31 0.27 50 57
with integral grilles PEL-N-1-17365-00001 0.32 0.27 50 57
11/16" Advanced Low-E IG PEL-N-1-17156-00001 3 3 air 0.31 0.30 56 56
with grilles-between-the-glass PEL-N-1-17778-00001 0.31 0.27 50 56
with integral grilles PEL-N-1-17366-00001 0.32 0.27 50 56
11/16" SunDefense Low-E IG PEL-N-1-17168-00001 2.5 2.5 air 0.30 0.22 52 58
with grilles-between-the-glass PEL-N-1-17790-00001 0.30 0.20 46 58
with integral grilles PEL-N-1-17378-00001 0.31 0.20 46 58
11/16" SunDefense Low-E IG PEL-N-1-17169-00001 3 3 air 0.31 0.23 51 57
with grilles-between-the-glass PEL-N-1-17791-00001 0.31 0.20 46 57
with integral grilles PEL-N-1-17379-00001 0.32 0.20 46 57
11/16" AdvancedComfort Low-E IG PEL-N-1-20363-00001 2.5 2.5 air 0.26 0.29 55 45 24
with grilles-between-the-glass PEL-N-1-20405-00001 0.26 0.27 49 45 23
with integral grilles PEL-N-1-20377-00001 0.26 0.27 49 45 23
11/16" AdvancedComfort Low-E IG PEL-N-1-20364-00001 3 3 air 0.26 0.29 54 44 24
with grilles-between-the-glass PEL-N-1-20406-00001 0.26 0.26 49 44 22
with integral grilles PEL-N-1-20378-00001 0.27 0.26 49 44 21
11/16" NaturalSun Low-E IG PEL-N-1-17126-00001 2.5 2.5 air 0.32 0.56 64 57 32
with grilles-between-the-glass PEL-N-1-17748-00001 0.32 0.50 57 57 29
with integral grilles PEL-N-1-17336-00001 0.33 0.50 57 57 27
11/16" NaturalSun Low-E IG PEL-N-1-17127-00001 3 3 air 0.32 0.55 63 56 31
with grilles-between-the-glass PEL-N-1-17749-00001 0.32 0.49 56 56 28
with integral grilles PEL-N-1-17337-00001 0.33 0.49 56 56 27
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-10
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad Wood Triple-Pane Glazing
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Mid. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
FIXED N NC SC S 1 2 31" Advanced Low-E IG PEL-N-1-17196-00001 3 3 3 argon 0.20 0.27 49 71 30
with grilles-between-the-glass PEL-N-1-17818-00001 0.21 0.24 44 71 27
with integral grilles PEL-N-1-20700-00001 0.22 0.24 43 71 26
1" Advanced Low-E IG PEL-N-1-20660-00001 3 3 3 Krypton 0.17 0.26 48 73 33
with grilles-between-the-glass PEL-N-1-20661-00001 0.17 0.24 43 73 32
with integral grilles PEL-N-1-20662-00001 0.18 0.24 43 73 31
1" SunDefense™ Low-E IG PEL-N-1-17203-00001 3 3 3 argon 0.20 0.20 45 71 26
with grilles-between-the-glass PEL-N-1-17825-00001 0.21 0.18 40 71 24
with integral grilles PEL-N-1-20708-00001 0.22 0.18 40 71 23
1" SunDefense™ Low-E IG PEL-N-1-20676-00001 3 3 3 Krypton 0.17 0.19 44 73 29
with grilles-between-the-glass PEL-N-1-20677-00001 0.17 0.18 39 73 29
with integral grilles PEL-N-1-20678-00001 0.18 0.18 39 73 28
1" NaturalSun Low-E IG PEL-N-1-17191-00001 3 3 3 argon 0.21 0.45 55 70 39
with grilles-between-the-glass PEL-N-1-17813-00001 0.21 0.40 49 70 36
with integral grilles PEL-N-1-20692-00001 0.22 0.40 48 70 35
1" NaturalSun Low-E IG PEL-N-1-20644-00001 3 3 3 Krypton 0.17 0.44 54 73 44
with grilles-between-the-glass PEL-N-1-20645-00001 0.17 0.40 48 73 41
with integral grilles PEL-N-1-20646-00001 0.18 0.40 48 73 40
HIGH ALTITUDE GLAZING1" Advanced Low-E IG PEL-N-1-17212-00001 3 3 3 air 0.24 0.27 49 66 25
with grilles-between-the-glass PEL-N-1-17834-00001 0.24 0.25 44 66 24
with integral grilles PEL-N-1-20724-00001 0.26 0.24 44 66 21
1" SunDefense Low-E IG PEL-N-1-17219-00001 3 3 3 air 0.24 0.20 45 66 21
with grilles-between-the-glass PEL-N-1-17841-00001 0.24 0.19 40 66 21
with integral grilles PEL-N-1-20732-00001 0.25 0.18 39 66 19
1" NaturalSun Low-E IG PEL-N-1-17207-00001 3 3 3 air 0.24 0.45 55 66 36
with grilles-between-the-glass PEL-N-1-17829-00001 0.25 0.40 49 66 32
with integral grilles PEL-N-1-20716-00001 0.26 0.40 48 66 30
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-11
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITWood ExteriorVent
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
VENT N NC SC S 1 2 311/16" Clear IG PEL-N-39-04782-00001 2.5 2.5 air 0.42 0.55 57 45
with integral grilles PEL-N-39-05388-00001 0.42 0.50 52 45
11/16" Clear IG PEL-N-39-04783-00001 3 3 air 0.43 0.54 56 45 with integral grilles PEL-N-39-05389-00001 0.43 0.49 51 45
11/16" Advanced Low-E IG PEL-N-39-04740-00001 2.5 2.5 argon 0.27 0.26 48 62 21
with integral grilles PEL-N-39-05346-00001 0.27 0.24 44 62 20
11/16" Advanced Low-E IG PEL-N-39-04741-00001 3 3 argon 0.27 0.26 48 61 21
with integral grilles PEL-N-39-05347-00001 0.27 0.24 43 61 20
11/16" SunDefense™ Low-E IG PEL-N-39-04753-00001 2.5 2.5 argon 0.27 0.19 45 63 17
with integral grilles PEL-N-39-05359-00001 0.27 0.18 41 63 16
11/16" SunDefense™ Low-E IG PEL-N-39-04754-00001 3 3 argon 0.26 0.19 44 62 18
with integral grilles PEL-N-39-05360-00001 0.26 0.18 40 62 18
11/16" AdvancedComfort Low-E IG PEL-N-39-06315-00001 2.5 2.5 argon 0.24 0.25 47 50 24
with integral grilles PEL-N-39-06357-00001 0.24 0.23 43 50 23
11/16" AdvancedComfort Low-E IG PEL-N-39-06316-00001 3 3 argon 0.24 0.25 47 49 24
with integral grilles PEL-N-39-06358-00001 0.24 0.23 42 49 23
11/16" NaturalSun Low-E IG PEL-N-39-04711-00001 2.5 2.5 argon 0.28 0.48 55 61 32
with integral grilles PEL-N-39-05317-00001 0.28 0.44 50 61 30
11/16" NaturalSun Low-E IG PEL-N-39-04712-00001 3 3 argon 0.28 0.47 54 61 32
with integral grilles PEL-N-39-05318-00001 0.28 0.43 49 61 30
TINTED GLAZING11/16" Bronze Advanced Low-E IG PEL-N-39-04698-00001 5 3 argon 0.28 0.23 31 61 18
with integral grilles PEL-N-39-05304-00001 0.29 0.21 28 61
11/16" Gray Advanced Low-E IG PEL-N-39-04724-00001 5 3 argon 0.28 0.21 27 61 17
with integral grilles PEL-N-39-05330-00001 0.29 0.19 24 61
11/16" Green Advanced Low-E IG PEL-N-39-04731-00001 5 3 argon 0.28 0.22 38 61 17
with integral grilles PEL-N-39-05337-00001 0.29 0.21 34 61
HIGH ALTITUDE GLAZING11/16" Advanced Low-E IG PEL-N-39-04817-00001 2.5 2.5 air 0.30 0.26 48 58
with integral grilles PEL-N-39-05423-00001 0.30 0.24 44 58
11/16" Advanced Low-E IG PEL-N-39-04818-00001 3 3 air 0.30 0.26 48 58 with integral grilles PEL-N-39-05424-00001 0.30 0.24 43 58
11/16" SunDefense Low-E IG PEL-N-39-04830-00001 2.5 2.5 air 0.30 0.20 45 59 with integral grilles PEL-N-39-05436-00001 0.30 0.18 41 59
11/16" SunDefense Low-E IG PEL-N-39-04831-00001 3 3 air 0.30 0.20 44 58 with integral grilles PEL-N-39-05437-00001 0.30 0.18 40 58
11/16" AdvancedComfort Low-E IG PEL-N-39-06322-00001 2.5 2.5 air 0.26 0.25 47 46 22
with integral grilles PEL-N-39-06364-00001 0.26 0.23 43 46 20
11/16" AdvancedComfort Low-E IG PEL-N-39-06323-00001 3 3 air 0.26 0.25 47 45 22
with integral grilles PEL-N-39-06365-00001 0.26 0.23 42 45 20
11/16" NaturalSun Low-E IG PEL-N-39-04788-00001 2.5 2.5 air 0.31 0.48 55 58 29
with integral grilles PEL-N-39-05394-00001 0.31 0.44 50 58 26
11/16" NaturalSun Low-E IG PEL-N-39-04789-00001 3 3 air 0.31 0.47 54 57 28
with integral grilles PEL-N-39-05395-00001 0.31 0.43 49 57 26
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-12
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITWood ExteriorTriple-Pane Glazing
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Mid. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
VENT UNITS N NC SC S 1 2 31" Advanced Low-E IG PEL-N-39-04858-00001 3 3 3 argon 0.21 0.23 42 71 27
with grilles-between-the-glass PEL-N-39-05464-00001 0.21 0.21 38 71 26
with integral grilles PEL-N-39-05060-00001 0.21 0.21 38 71 26
1" Advanced Low-E IG PEL-N-39-06443-00001 3 3 3 Krypton 0.18 0.23 42 76 30
with grilles-between-the-glass PEL-N-39-06444-00001 0.18 0.21 38 76 29
with integral grilles PEL-N-39-06445-00001 0.18 0.21 38 76 29
1" SunDefense™ Low-E IG PEL-N-39-04865-00001 3 3 3 argon 0.21 0.18 39 71 24
with grilles-between-the-glass PEL-N-39-05471-00001 0.21 0.16 35 71 23
with integral grilles PEL-N-39-05067-00001 0.21 0.16 35 71 23
1" SunDefense™ Low-E IG PEL-N-39-06459-00001 3 3 3 Krypton 0.17 0.17 39 76 28
with grilles-between-the-glass PEL-N-39-06460-00001 0.18 0.16 35 76 26
with integral grilles PEL-N-39-06461-00001 0.18 0.16 35 76 26
1" NaturalSun Low-E IG PEL-N-39-04853-00001 3 3 3 argon 0.21 0.39 48 70 36
with grilles-between-the-glass PEL-N-39-05459-00001 0.21 0.35 43 70 34
with integral grilles PEL-N-39-05055-00001 0.21 0.35 43 70 34
1" NaturalSun Low-E IG PEL-N-39-06427-00001 3 3 3 Krypton 0.18 0.39 48 75 40
with grilles-between-the-glass PEL-N-39-06428-00001 0.18 0.35 43 75 37
with integral grilles PEL-N-39-06429-00001 0.19 0.35 43 75 36
HIGH ALTITUDE GLAZING1" Advanced Low-E IG PEL-N-39-04874-00001 3 3 3 air 0.24 0.24 42 67 24
with grilles-between-the-glass PEL-N-39-05480-00001 0.24 0.22 38 67 22
with integral grilles PEL-N-39-05076-00001 0.24 0.22 38 67 22
1" SunDefense Low-E IG PEL-N-39-04881-00001 3 3 3 air 0.24 0.18 39 67 20
with grilles-between-the-glass PEL-N-39-05487-00001 0.24 0.16 35 67 19
with integral grilles PEL-N-39-05083-00001 0.24 0.16 35 67 19
1" NaturalSun Low-E IG PEL-N-39-04869-00001 3 3 3 air 0.24 0.39 48 66 32
with grilles-between-the-glass PEL-N-39-05475-00001 0.24 0.35 43 66 30
with integral grilles PEL-N-39-05071-00001 0.24 0.35 43 66 30
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-13
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITWood ExteriorFixed
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
FIXED N NC SC S 1 2 311/16" Clear IG PEL-N-41-07038-00001 2.5 2.5 air 0.44 0.63 66 45
with integral grilles PEL-N-41-07644-00001 0.44 0.57 59 45
11/16" Clear IG PEL-N-41-07039-00001 3 3 air 0.45 0.62 65 44 with integral grilles PEL-N-41-07645-00001 0.45 0.56 58 44
11/16" Advanced Low-E IG PEL-N-41-06996-00001 2.5 2.5 argon 0.26 0.30 56 62 25
with integral grilles PEL-N-41-07602-00001 0.26 0.27 50 62 23
11/16" Advanced Low-E IG PEL-N-41-06997-00001 3 3 argon 0.26 0.30 56 61 25
with integral grilles PEL-N-41-07603-00001 0.26 0.27 50 61 23
11/16" SunDefense™ Low-E IG PEL-N-41-07009-00001 2.5 2.5 argon 0.26 0.22 52 62 20
with integral grilles PEL-N-41-07615-00001 0.26 0.20 46 62 19
11/16" SunDefense™ Low-E IG PEL-N-41-07010-00001 3 3 argon 0.26 0.22 51 61 20
with integral grilles PEL-N-41-07616-00001 0.26 0.20 46 61 19
11/16" AdvancedComfort Low-E IG PEL-N-41-10186-00001 2.5 2.5 argon 0.22 0.29 55 49 29
with integral grilles PEL-N-41-10228-00001 0.22 0.26 49 49 27
11/16" AdvancedComfort Low-E IG PEL-N-41-10187-00001 3 3 argon 0.22 0.29 54 48 29
with integral grilles PEL-N-41-10229-00001 0.22 0.26 49 48 27
11/16" NaturalSun Low-E IG PEL-N-41-06967-00001 2.5 2.5 argon 0.27 0.56 64 61 38
with integral grilles PEL-N-41-07573-00001 0.27 0.50 57 61 35
11/16" NaturalSun Low-E IG PEL-N-41-06968-00001 3 3 argon 0.27 0.55 63 60 38
with integral grilles PEL-N-41-07574-00001 0.27 0.49 56 60 34
TINTED GLAZING11/16" Bronze Advanced Low-E IG PEL-N-41-06954-00001 5 3 argon 0.27 0.26 36 60 21
with integral grilles PEL-N-41-07560-00001 0.28 0.24 32 60 19
11/16" Gray Advanced Low-E IG PEL-N-41-06980-00001 5 3 argon 0.27 0.24 31 60 20
with integral grilles PEL-N-41-07586-00001 0.28 0.22 28 60 17
11/16" Green Advanced Low-E IG PEL-N-41-06987-00001 5 3 argon 0.27 0.26 44 60 21
with integral grilles PEL-N-41-07593-00001 0.28 0.23 39 60 18
HIGH ALTITUDE GLAZING11/16" Advanced Low-E IG PEL-N-41-07073-00001 2.5 2.5 air 0.30 0.30 56 58
with integral grilles PEL-N-41-07679-00001 0.30 0.27 50 58
11/16" Advanced Low-E IG PEL-N-41-07074-00001 3 3 air 0.30 0.30 56 57 with integral grilles PEL-N-41-07680-00001 0.30 0.27 50 57
11/16" SunDefense Low-E IG PEL-N-41-07086-00001 2.5 2.5 air 0.29 0.22 52 58 with integral grilles PEL-N-41-07692-00001 0.29 0.20 46 58
11/16" SunDefense Low-E IG PEL-N-41-07087-00001 3 3 air 0.30 0.23 51 57 with integral grilles PEL-N-41-07693-00001 0.30 0.20 46 57
11/16" AdvancedComfort Low-E IG PEL-N-41-10193-00001 2.5 2.5 air 0.25 0.29 55 45 25
with integral grilles PEL-N-41-10235-00001 0.25 0.26 49 45 23
11/16" AdvancedComfort Low-E IG PEL-N-41-10194-00001 3 3 air 0.25 0.29 54 44 25
with integral grilles PEL-N-41-10236-00001 0.25 0.26 49 44 23
11/16" NaturalSun Low-E IG PEL-N-41-07044-00001 2.5 2.5 air 0.31 0.56 64 57 33
with integral grilles PEL-N-41-07650-00001 0.31 0.50 57 57 30
11/16" NaturalSun Low-E IG PEL-N-41-07045-00001 3 3 air 0.31 0.55 63 56 33
with integral grilles PEL-N-41-07651-00001 0.31 0.49 56 56 29
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-14
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITWood ExteriorTriple-Pane Glazing
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Mid. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
FIXED UNITS N NC SC S 1 2 31" Advanced Low-E IG PEL-N-41-07114-00001 3 3 3 argon 0.19 0.27 49 71 31
with grilles-between-the-glass PEL-N-41-07720-00001 0.20 0.24 43 71 28
with integral grilles PEL-N-41-07316-00001 0.20 0.24 43 71 28
1" Advanced Low-E IG PEL-N-41-10426-00001 3 3 3 Krypton 0.16 0.26 48 76 35
with grilles-between-the-glass PEL-N-41-10427-00001 0.16 0.24 43 76 33
with integral grilles PEL-N-41-10428-00001 0.17 0.24 43 76 32
1" SunDefense™ Low-E IG PEL-N-41-07121-00001 3 3 3 argon 0.19 0.20 45 71 27
with grilles-between-the-glass PEL-N-41-07727-00001 0.20 0.18 40 71 25
with integral grilles PEL-N-41-07323-00001 0.20 0.18 40 71 25
1" SunDefense™ Low-E IG PEL-N-41-10442-00001 3 3 3 Krypton 0.16 0.19 44 76 31
with grilles-between-the-glass PEL-N-41-10443-00001 0.16 0.18 39 76 30
with integral grilles PEL-N-41-10444-00001 0.17 0.18 39 76 29
1" NaturalSun Low-E IG PEL-N-41-07109-00001 3 3 3 argon 0.20 0.45 55 71 41
with grilles-between-the-glass PEL-N-41-07715-00001 0.20 0.40 50 71 38
with integral grilles PEL-N-41-07311-00001 0.20 0.40 50 71 38
1" NaturalSun Low-E IG PEL-N-41-10410-00001 3 3 3 Krypton 0.16 0.44 54 75 45
with grilles-between-the-glass PEL-N-41-10411-00001 0.16 0.40 48 75 43
with integral grilles PEL-N-41-10412-00001 0.17 0.40 48 75 41
HIGH ALTITUDE GLAZING1" Advanced Low-E IG PEL-N-41-07130-00001 3 3 3 air 0.23 0.27 49 67 26
with grilles-between-the-glass PEL-N-41-07736-00001 0.24 0.24 44 67 24
with integral grilles PEL-N-41-07332-00001 0.24 0.24 44 67 24
1" SunDefense Low-E IG PEL-N-41-07137-00001 3 3 3 air 0.23 0.20 45 67 22
with grilles-between-the-glass PEL-N-41-07743-00001 0.23 0.18 40 67 21
with integral grilles PEL-N-41-07339-00001 0.23 0.18 40 67 21
1" NaturalSun Low-E IG PEL-N-41-07125-00001 3 3 3 air 0.23 0.45 55 66 37
with grilles-between-the-glass PEL-N-41-07731-00001 0.24 0.40 50 66 33
with integral grilles PEL-N-41-07327-00001 0.24 0.40 50 66 33
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-15
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITClad HurricaneShield® Impact Resistant Vent
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
VENT - HURRICANESHIELD® LAMINATED IMPACT-RESISTANT N NC SC S 1 2 39/16" Clear Single (SGP) PEL-N-11-08984-00001 14 NA NA 0.75 0.49 58 16
with applied grilles PEL-N-11-09194-00001 0.75 0.45 52 16
11/16" Clear IG PEL-N-11-09001-00001 3 7 argon 0.44 0.51 55 44
with grilles-between-the-glass PEL-N-11-09623-00001 0.45 0.46 50 42
with integral grilles PEL-N-11-09211-00001 0.45 0.46 50 42
11/16" Advanced Low-E IG PEL-N-11-09039-00001 3 7 argon 0.33 0.26 47 55
with grilles-between-the-glass PEL-N-11-09661-00001 0.34 0.24 42 55
with integral grilles PEL-N-11-09249-00001 0.34 0.24 42 55
11/16" SunDefense™ Low-E IG PEL-N-11-09052-00001 3 7 argon 0.33 0.20 43 55
with grilles-between-the-glass PEL-N-11-09674-00001 0.34 0.18 39 55
with integral grilles PEL-N-11-09262-00001 0.34 0.18 39 55
1" Clear IG PEL-N-11-09000-00001 5 10 argon 0.41 0.49 54 46
with grilles-between-the-glass PEL-N-11-09622-00001 0.41 0.44 49 46
with integral grilles PEL-N-11-09210-00001 0.41 0.44 49 46
1" Advanced Low-E IG PEL-N-11-09038-00001 5 10 argon 0.28 0.25 46 59 19
with grilles-between-the-glass PEL-N-11-09660-00001 0.29 0.23 42 59
with integral grilles PEL-N-11-09248-00001 0.29 0.23 42 59
1" SunDefense Low-E IG PEL-N-11-09051-00001 5 10 argon 0.28 0.19 43 59 16
with grilles-between-the-glass PEL-N-11-09673-00001 0.29 0.18 38 59
with integral grilles PEL-N-11-09261-00001 0.29 0.18 38 59
TINTED GLAZING LAMINATED IMPACT-RESISTANT9/16" Bronze Single (SGP) PEL-N-11-08981-00001 14 NA NA 0.75 0.41 35 16
with applied grilles PEL-N-11-09191-00001 0.75 0.38 32 16
11/16" Bronze Advanced Low-E IG PEL-N-11-09030-00001 3 7 argon 0.33 0.25 34 55
with grilles-between-the-glass PEL-N-11-09652-00001 0.34 0.23 31 55
with integral grilles PEL-N-11-09240-00001 0.34 0.23 31 55
1" Bronze IG PEL-N-11-09029-00001 5 10 argon 0.41 0.37 35 46
with grilles-between-the-glass PEL-N-11-09651-00001 0.41 0.33 32 46
with integral grilles PEL-N-11-09239-00001 0.41 0.33 32 46
9/16" Gray Single (SGP) PEL-N-11-08982-00001 14 NA NA 0.75 0.39 28 16 with applied grilles PEL-N-11-09192-00001 0.75 0.36 25 16
11/16" Gray Advanced Low-E IG PEL-N-11-09041-00001 3 7 argon 0.33 0.25 31 55
with grilles-between-the-glass PEL-N-11-09663-00001 0.34 0.23 28 55
with integral grilles PEL-N-11-09251-00001 0.34 0.23 28 55
1" Gray IG PEL-N-11-09040-00001 5 10 argon 0.41 0.33 30 46
with grilles-between-the-glass PEL-N-11-09662-00001 0.41 0.30 27 46
with integral grilles PEL-N-11-09250-00001 0.41 0.30 27 46
9/16" Green Single (SGP) PEL-N-11-08987-00001 14 NA NA 0.75 0.39 49 16 with applied grilles PEL-N-11-09197-00001 0.75 0.35 44 16
11/16" Green Advanced Low-E IG PEL-N-11-09043-00001 3 7 argon 0.33 0.25 42 55
with grilles-between-the-glass PEL-N-11-09665-00001 0.34 0.23 38 55
with integral grilles PEL-N-11-09253-00001 0.34 0.23 38 55
1" Green IG PEL-N-11-09042-00001 5 10 argon 0.41 0.30 43 46
with grilles-between-the-glass PEL-N-11-09664-00001 0.41 0.27 39 46
with integral grilles PEL-N-11-09252-00001 0.41 0.27 39 46
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-16
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITClad HurricaneShield® Impact ResistantFixed
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
FIXED - HURRICANESHIELD® LAMINATED IMPACT-RESISTANT N NC SC S 1 2 39/16" Clear Single (SGP) PEL-N-1-17031-00001 14 NA NA 0.81 0.57 67 16
with applied grilles PEL-N-1-17241-00001 0.81 0.51 60 16
11/16" Clear IG PEL-N-1-17048-00001 3 7 argon 0.46 0.59 64 44
with grilles-between-the-glass PEL-N-1-17670-00001 0.46 0.53 57 44
with integral grilles PEL-N-1-17258-00001 0.46 0.53 57 44
11/16" Advanced Low-E IG PEL-N-1-17086-00001 3 7 argon 0.33 0.30 54 55
with grilles-between-the-glass PEL-N-1-17708-00001 0.34 0.27 49 55
with integral grilles PEL-N-1-17296-00001 0.34 0.27 49 55
11/16" SunDefense™ Low-E IG PEL-N-1-17099-00001 3 7 argon 0.32 0.22 50 55
with grilles-between-the-glass PEL-N-1-17721-00001 0.34 0.20 45 55
with integral grilles PEL-N-1-17309-00001 0.34 0.20 45 55
1" Clear IG PEL-N-1-17047-00001 5 10 argon 0.42 0.56 63 46
with grilles-between-the-glass PEL-N-1-17669-00001 0.42 0.50 56 46
with integral grilles PEL-N-1-17257-00001 0.42 0.50 56 46
1" Advanced Low-E IG PEL-N-1-17085-00001 5 10 argon 0.27 0.29 53 59 23
with grilles-between-the-glass PEL-N-1-17707-00001 0.28 0.26 48 59 20
with integral grilles PEL-N-1-17295-00001 0.28 0.26 48 59 20
1" SunDefense Low-E IG PEL-N-1-17098-00001 5 10 argon 0.27 0.22 49 59 19
with grilles-between-the-glass PEL-N-1-17720-00001 0.28 0.20 44 59 16
with integral grilles PEL-N-1-17308-00001 0.28 0.20 44 59 16
TINTED GLAZING LAMINATED IMPACT-RESISTANT9/16" Bronze Single (SGP) PEL-N-1-17028-00001 14 NA NA 0.81 0.48 41 16
with applied grilles PEL-N-1-17238-00001 0.81 0.43 37 16
11/16" Bronze Advanced Low-E IG PEL-N-1-17077-00001 3 7 argon 0.33 0.28 39 55
with grilles-between-the-glass PEL-N-1-17699-00001 0.34 0.26 35 55
with integral grilles PEL-N-1-17287-00001 0.34 0.26 35 55
1" Bronze IG PEL-N-1-17076-00001 5 10 argon 0.42 0.42 41 46
with grilles-between-the-glass PEL-N-1-17698-00001 0.42 0.38 36 46
with integral grilles PEL-N-1-17286-00001 0.42 0.38 36 46
9/16" Gray Single (SGP) PEL-N-1-17029-00001 14 NA NA 0.81 0.45 32 16 with applied grilles PEL-N-1-17239-00001 0.81 0.41 28 16
11/16" Gray Advanced Low-E IG PEL-N-1-17088-00001 3 7 argon 0.33 0.28 36 55
with grilles-between-the-glass PEL-N-1-17710-00001 0.34 0.26 32 55
with integral grilles PEL-N-1-17298-00001 0.34 0.26 32 55
1" Gray IG PEL-N-1-17087-00001 5 10 argon 0.42 0.38 35 46
with grilles-between-the-glass PEL-N-1-17709-00001 0.42 0.34 31 46
with integral grilles PEL-N-1-17297-00001 0.42 0.34 31 46
9/16" 9/16" Green Single (SGP) PEL-N-1-17034-00001 14 NA NA 0.81 0.44 57 16 with applied grilles PEL-N-1-17244-00001 0.81 0.40 51 16
11/16" 11/16" Green Advanced Low-E IG PEL-N-1-17090-00001 3 7 argon 0.33 0.29 49 55
with grilles-between-the-glass PEL-N-1-17712-00001 0.34 0.26 44 55
with integral grilles PEL-N-1-17300-00001 0.34 0.26 44 55
1" Green IG PEL-N-1-17089-00001 5 10 argon 0.42 0.34 50 46
with grilles-between-the-glass PEL-N-1-17711-00001 0.42 0.31 44 46
with integral grilles PEL-N-1-17299-00001 0.42 0.31 44 46
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-17
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad WoodVent
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Mid. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
VENT WITH TRIPLE-PANE GLAZING WITH CLEAR HGP N NC SC S 1 2 35/8" Clear IG PEL-N-16-01343-00001 3 3 3 air 0.36 0.44 47 58
5/8" Advanced Low-E IG PEL-N-16-01396-00001 2.5 2.5 2.5 argon 0.28 0.22 40 62 17
5/8" AdvancedComfort Low-E IG PEL-N-16-01576-00001 2.5 2.5 2.5 argon 0.25 0.22 39 62 21
5/8" SunDefense™ Low-E IG PEL-N-16-01354-00001 2.5 2.5 2.5 argon 0.28 0.17 37 62
5/8" SunDefense™ Low-E IG PEL-N-16-01361-00001 3 3 3 argon 0.28 0.17 37 62
5/8" SunDefense™ Low-E IG PEL-N-16-01368-00001 4 4 4 argon 0.29 0.17 36 61
5/8" NaturalSun Low-E IG PEL-N-16-01750-00001 2.5 2.5 2.5 argon 0.28 0.39 46 62 27
TINTED GLAZING WITH CLEAR HGP5/8" Bronze Advanced Low-E IG PEL-N-16-01432-00001 5 3 2.5 argon 0.30 0.19 26 61
5/8" Bronze Advanced Low-E IG PEL-N-16-01433-00001 5 3 3 argon 0.30 0.19 26 61
5/8" Gray Advanced Low-E IG PEL-N-16-01456-00001 5 3 2.5 argon 0.30 0.18 22 61
5/8" Gray Advanced Low-E IG PEL-N-16-01457-00001 5 3 3 argon 0.30 0.18 22 61
5/8" Green Advanced Low-E IG PEL-N-16-01480-00001 5 3 2.5 argon 0.30 0.19 31 61
5/8" Green Advanced Low-E IG PEL-N-16-01481-00001 5 3 3 argon 0.30 0.19 31 60
HIGH ALTITUDE GLAZING WITH CLEAR HGP5/8" Advanced Low-E IG PEL-N-16-01421-00001 3 3 3 air 0.30 0.22 40 61
5/8" Advanced Low-E IG PEL-N-16-01428-00001 4 4 4 air 0.32 0.22 39 61
5/8" AdvancedComfort Low-E IG PEL-N-16-01618-00001 3 3 3 air 0.28 0.22 39 62 17
5/8" AdvancedComfort Low-E IG PEL-N-16-01666-00001 4 4 4 air 0.29 0.21 38 62
5/8" SunDefense Low-E IG PEL-N-16-01379-00001 3 3 3 air 0.30 0.17 37 61
5/8" SunDefense Low-E IG PEL-N-16-01386-00001 4 4 4 air 0.32 0.17 36 61
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-18
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad WoodFixed
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Mid. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
FIXED WITH TRIPLE-PANE GLAZING WITH CLEAR HGP N NC SC S 1 2 35/8" Clear IG PEL-N-19-01343-00001 3 3 3 air 0.35 0.53 57 58 27
5/8" Advanced Low-E IG PEL-N-19-01396-00001 2.5 2.5 2.5 argon 0.25 0.26 49 62 24
5/8" Advanced Low-E IG PEL-N-19-01403-00001 3 3 3 argon 0.25 0.26 48 62 24
5/8" Advanced Low-E IG PEL-N-19-01410-00001 4 4 4 argon 0.27 0.26 47 61 21
5/8" SunDefense™ Low-E IG PEL-N-19-01354-00001 2.5 2.5 2.5 argon 0.24 0.20 45 62 22
5/8" SunDefense™ Low-E IG PEL-N-19-01361-00001 3 3 3 argon 0.25 0.20 44 62 20
5/8" SunDefense™ Low-E IG PEL-N-19-01368-00001 4 4 4 argon 0.27 0.20 44 62 18
5/8" AdvancedComfort Low-E IG PEL-N-19-01576-00001 2.5 2.5 2.5 argon 0.22 0.26 48 63 27
5/8" AdvancedComfort Low-E IG PEL-N-19-01624-00001 3 3 3 argon 0.23 0.26 47 63 26
5/8" AdvancedComfort Low-E IG PEL-N-19-01672-00001 4 4 4 argon 0.24 0.25 46 62 24
5/8" NaturalSun Low-E IG PEL-N-19-01750-00001 2.5 2.5 2.5 argon 0.25 0.46 55 62 35
5/8" NaturalSun Low-E IG PEL-N-19-01757-00001 3 3 3 argon 0.26 0.45 55 62 33
5/8" NaturalSun Low-E IG PEL-N-19-01764-00001 4 4 4 argon 0.27 0.44 54 61 32
TINTED GLAZING WITH CLEAR HGP5/8" Bronze Advanced Low-E IG PEL-N-19-01433-00001 5 3 3 argon 0.27 0.23 31 61 20
5/8" Gray Advanced Low-E IG PEL-N-19-01457-00001 5 3 3 argon 0.27 0.21 27 61 18
5/8" Green Advanced Low-E IG PEL-N-19-01481-00001 5 3 3 argon 0.27 0.22 38 61 19
HIGH ALTITUDE GLAZING WITH CLEAR HGP5/8" Advanced Low-E IG PEL-N-19-01421-00001 3 3 3 air 0.28 0.26 0.48 61 20
5/8" Advanced Low-E IG PEL-N-19-01428-00001 4 4 4 air 0.30 0.26 0.47 61
5/8" AdvancedComfort Low-E IG PEL-N-19-01618-00001 3 3 3 air 0.25 0.26 0.47 62 24
5/8" AdvancedComfort Low-E IG PEL-N-19-01666-00001 4 4 4 air 0.26 0.25 0.46 62 22
5/8" SunDefense Low-E IG PEL-N-19-01379-00001 3 3 3 air 0.28 0.20 0.44 61 17
5/8" SunDefense Low-E IG PEL-N-19-01386-00001 4 4 4 air 0.29 0.20 0.44 61
5/8" NaturalSun Low-E IG PEL-N-19-01775-00001 3 3 3 air 0.28 0.45 0.55 61 31
5/8" NaturalSun Low-E IG PEL-N-19-01782-00001 4 4 4 air 0.30 0.43 0.54 61 27
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-19
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad WoodVent
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
VENT UNITS N NC SC S 1 2 311/16" Advanced LowE IG PEL-N-14-00266-00001 2.5 2.5 argon 0.29 0.27 51 56
with grilles-between-the-glass PEL-N-14-00265-00001 0.29 0.25 47 56 with Simulated Divided Light PEL-N-14-00267-00001 0.29 0.25 47 56
11/16" Advanced LowE IG PEL-N-14-00281-00001 3 3 argon 0.29 0.27 51 56 with grilles-between-the-glass PEL-N-14-00280-00001 0.29 0.25 46 56 with Simulated Divided Light PEL-N-14-00282-00001 0.29 0.25 46 56
11/16" SunDefense™ Low-E IG PEL-N-14-00269-00001 2.5 2.5 argon 0.29 0.20 48 57 with grilles-between-the-glass PEL-N-14-00268-00001 0.29 0.19 43 57 with Simulated Divided Light PEL-N-14-00270-00001 0.29 0.19 43 57
11/16" SunDefense™ Low-E IG PEL-N-14-00284-00001 3 3 argon 0.29 0.20 47 56 with grilles-between-the-glass PEL-N-14-00283-00001 0.29 0.19 43 56 with Simulated Divided Light PEL-N-14-00285-00001 0.29 0.19 43 56
11/16" AdvancedComfort Low-E IG PEL-N-14-00455-00001 2.5 2.5 argon 0.25 0.27 50 46 24 with grilles-between-the-glass PEL-N-14-00454-00001 0.25 0.25 46 46 23 with Simulated Divided Light PEL-N-14-00456-00001 0.25 0.25 46 46 23
11/16" AdvancedComfort Low-E IG PEL-N-14-00458-00001 3 3 argon 0.25 0.27 50 45 24 with grilles-between-the-glass PEL-N-14-00457-00001 0.25 0.25 45 45 23 with Simulated Divided Light PEL-N-14-00459-00001 0.25 0.25 45 45 23
11/16" NaturalSun LowE IG PEL-N-14-00263-00001 2.5 2.5 argon 0.30 0.51 58 56 32 with grilles-between-the-glass PEL-N-14-00262-00001 0.30 0.47 53 56 29 with Simulated Divided Light PEL-N-14-00264-00001 0.30 0.47 53 56 29
11/16" NaturalSun LowE IG PEL-N-14-00278-00001 3 3 argon 0.30 0.50 58 55 31 with grilles-between-the-glass PEL-N-14-00277-00001 0.30 0.46 52 55 29 with Simulated Divided Light PEL-N-14-00279-00001 0.30 0.46 52 55 29
HIGH ALTITUDE GLAZING11/16" Advanced LowE IG PEL-N-14-00296-00001 2.5 2.5 air 0.33 0.28 51 53
with grilles-between-the-glass PEL-N-14-00295-00001 0.33 0.25 47 53 with Simulated Divided Light PEL-N-14-00297-00001 0.33 0.25 47 53
11/16" Advanced LowE IG PEL-N-14-00311-00001 3 3 air 0.33 0.28 51 52 with grilles-between-the-glass PEL-N-14-00310-00001 0.33 0.25 46 52 with Simulated Divided Light PEL-N-14-00312-00001 0.33 0.25 46 52
11/16" SunDefense™ Low-E IG PEL-N-14-00299-00001 2.5 2.5 air 0.32 0.21 48 54 with grilles-between-the-glass PEL-N-14-00298-00001 0.32 0.19 43 54 with Simulated Divided Light PEL-N-14-00300-00001 0.32 0.19 43 54
11/16" SunDefense Low-E IG PEL-N-14-00314-00001 3 3 air 0.33 0.21 47 53 with grilles-between-the-glass PEL-N-14-00313-00001 0.33 0.19 43 53 with Simulated Divided Light PEL-N-14-00315-00001 0.33 0.19 43 53
11/16" AdvancedComfort Low-E IG PEL-N-14-00461-00001 2.5 2.5 air 0.27 0.27 50 43 22 with grilles-between-the-glass PEL-N-14-00460-00001 0.27 0.25 46 43 20 with Simulated Divided Light PEL-N-14-00462-00001 0.27 0.25 46 43 20
11/16" AdvancedComfort Low-E IG PEL-N-14-00464-00001 3 3 air 0.28 0.27 50 42 20 with grilles-between-the-glass PEL-N-14-00463-00001 0.28 0.25 45 42 19 with Simulated Divided Light PEL-N-14-00465-00001 0.28 0.25 45 42 19
11/16" NaturalSun LowE IG PEL-N-14-00293-00001 2.5 2.5 air 0.33 0.51 58 53 28 with grilles-between-the-glass PEL-N-14-00292-00001 0.33 0.47 53 53 26 with Simulated Divided Light PEL-N-14-00294-00001 0.33 0.47 53 53 26
11/16" NaturalSun LowE IG PEL-N-14-00308-00001 3 3 air 0.34 0.50 58 52 26 with grilles-between-the-glass PEL-N-14-00307-00001 0.34 0.46 52 52 with Simulated Divided Light PEL-N-14-00309-00001 0.34 0.46 52 52
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-20
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad WoodFixed
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
FIXED UNITS N NC SC S 1 2 311/16" Advanced LowE IG PEL-N-22-00398-00001 2.5 2.5 argon 0.28 0.31 58 59 23
with grilles-between-the-glass PEL-N-22-00399-00001 0.28 0.28 52 59 21
with Simulated Divided Light PEL-N-22-00400-00001 0.28 0.28 52 59 21
11/16" Advanced LowE IG PEL-N-22-00401-00001 3 3 argon 0.28 0.31 58 58 23
with grilles-between-the-glass PEL-N-22-00402-00001 0.28 0.28 52 58 21
with Simulated Divided Light PEL-N-22-00403-00001 0.28 0.28 52 58 21
11/16" Advanced LowE IG PEL-N-22-00404-00001 4 4 argon 0.28 0.30 57 56 22
with grilles-between-the-glass PEL-N-22-00405-00001 0.30 0.27 51 56
with Simulated Divided Light PEL-N-22-00406-00001 0.29 0.27 51 56
11/16" SunDefense™ Low-E IG PEL-N-22-00434-00001 2.5 2.5 argon 0.28 0.23 54 57 18
with grilles-between-the-glass PEL-N-22-00435-00001 0.28 0.21 48 57 17
with Simulated Divided Light PEL-N-22-00436-00001 0.28 0.21 48 57 17
11/16" SunDefense Low-E IG PEL-N-22-00437-00001 3 3 argon 0.27 0.23 53 58 19
with grilles-between-the-glass PEL-N-22-00438-00001 0.27 0.21 48 58 18
with Simulated Divided Light PEL-N-22-00439-00001 0.27 0.21 48 58 18
11/16" SunDefense Low-E IG PEL-N-22-00440-00001 4 4 argon 0.28 0.23 53 56 18
with grilles-between-the-glass PEL-N-22-00441-00001 0.29 0.21 47 56
with Simulated Divided Light PEL-N-22-00442-00001 0.29 0.21 47 56
11/16" AdvancedComfort Low-E IG PEL-N-22-00497-00001 2.5 2.5 argon 0.24 0.30 57 45 27
with grilles-between-the-glass PEL-N-22-00498-00001 0.24 0.27 51 45 25
with Simulated Divided Light PEL-N-22-00499-00001 0.24 0.27 51 45 25
11/16" AdvancedComfort Low-E IG PEL-N-22-00500-00001 3 3 argon 0.24 0.30 56 46 27
with grilles-between-the-glass PEL-N-22-00501-00001 0.24 0.27 50 46 25
with Simulated Divided Light PEL-N-22-00502-00001 0.24 0.27 50 46 25
11/16" AdvancedComfort Low-E IG PEL-N-22-00503-00001 4 4 argon 0.24 0.30 56 44 27
with grilles-between-the-glass PEL-N-22-00504-00001 0.25 0.27 50 44 24
with Simulated Divided Light PEL-N-22-00505-00001 0.25 0.27 50 44 24
11/16" NaturalSun LowE IG PEL-N-22-00416-00001 2.5 2.5 argon 0.31 0.59 66 56 35
with grilles-between-the-glass PEL-N-22-00417-00001 0.31 0.53 59 56 32
with Simulated Divided Light PEL-N-22-00418-00001 0.31 0.53 59 56 32
11/16" NaturalSun LowE IG PEL-N-22-00419-00001 3 3 argon 0.29 0.57 65 57 36
with grilles-between-the-glass PEL-N-22-00420-00001 0.29 0.51 58 57 33
with Simulated Divided Light PEL-N-22-00421-00001 0.29 0.51 58 57 33
11/16" NaturalSun LowE IG PEL-N-22-00422-00001 4 4 argon 0.29 0.55 65 56 35
with grilles-between-the-glass PEL-N-22-00423-00001 0.31 0.50 58 56 30
with Simulated Divided Light PEL-N-22-00424-00001 0.30 0.50 58 56 31
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-21
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GLAZING PERFORMANCE - TOTAL UNITAluminum-Clad WoodFixed
Gla
zing
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performane Values1
Shaded Areas Meet ENERGY STAR® Performance
Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT
%
CR
U. S. Canada 2
Zone ER Zone
FIXED UNITS - HIGH ALTITUDE GLAZING N NC SC S 1 2 311/16" Advanced LowE IG PEL-N-22-00407-00001 2.5 2.5 air 0.32 0.31 58 54 18
with grilles-between-the-glass PEL-N-22-00408-00001 0.32 0.28 52 54 16
with Simulated Divided Light PEL-N-22-00409-00001 0.32 0.28 52 54 16
11/16" Advanced LowE IG PEL-N-22-00410-00001 3 3 air 0.32 0.31 58 55 18
with grilles-between-the-glass PEL-N-22-00411-00001 0.32 0.28 52 55 16
with Simulated Divided Light PEL-N-22-00412-00001 0.32 0.28 52 55 16
11/16" Advanced LowE IG PEL-N-22-00413-00001 4 4 air 0.33 0.31 57 52
with grilles-between-the-glass PEL-N-22-00414-00001 0.35 0.28 51 52
with Simulated Divided Light PEL-N-22-00415-00001 0.34 0.28 51 52
11/16" SunDefense™ Low-E IG PEL-N-22-00443-00001 2.5 2.5 air 0.32 0.23 54 54 13
with grilles-between-the-glass PEL-N-22-00444-00001 0.32 0.21 48 54
with Simulated Divided Light PEL-N-22-00445-00001 0.32 0.21 48 54
11/16" SunDefense Low-E IG PEL-N-22-00446-00001 3 3 air 0.31 0.23 53 55 15
with grilles-between-the-glass PEL-N-22-00447-00001 0.31 0.21 48 55 13
with Simulated Divided Light PEL-N-22-00448-00001 0.31 0.21 48 55 13
11/16" SunDefense Low-E IG PEL-N-22-00449-00001 4 4 air 0.33 0.24 53 53
with grilles-between-the-glass PEL-N-22-00450-00001 0.34 0.21 47 53
with Simulated Divided Light PEL-N-22-00451-00001 0.34 0.21 47 53
11/16" AdvancedComfort Low-E IG PEL-N-22-00506-00001 2.5 2.5 air 0.27 0.30 57 42 24
with grilles-between-the-glass PEL-N-22-00507-00001 0.27 0.27 51 42 22
with Simulated Divided Light PEL-N-22-00508-00001 0.27 0.27 51 42 22
11/16" AdvancedComfort Low-E IG PEL-N-22-00509-00001 3 3 air 0.26 0.30 56 42 25
with grilles-between-the-glass PEL-N-22-00510-00001 0.26 0.27 50 42 23
with Simulated Divided Light PEL-N-22-00511-00001 0.26 0.27 50 42 23
11/16" AdvancedComfort Low-E IG PEL-N-22-00512-00001 4 4 air 0.28 0.30 56 40 22
with grilles-between-the-glass PEL-N-22-00513-00001 0.29 0.27 50 40 19
with Simulated Divided Light PEL-N-22-00514-00001 0.28 0.27 50 40 21
11/16" NaturalSun LowE IG PEL-N-22-00425-00001 2.5 2.5 air 0.34 0.58 66 52 31
with grilles-between-the-glass PEL-N-22-00426-00001 0.34 0.53 59 52 28
with Simulated Divided Light PEL-N-22-00427-00001 0.34 0.53 59 52 28
11/16" NaturalSun LowE IG PEL-N-22-00428-00001 3 3 air 0.32 0.56 65 54 32
with grilles-between-the-glass PEL-N-22-00429-00001 0.32 0.51 58 54 29
with Simulated Divided Light PEL-N-22-00430-00001 0.32 0.51 58 54 29
11/16" NaturalSun LowE IG PEL-N-22-00431-00001 4 4 air 0.34 0.55 65 52 29
with grilles-between-the-glass PEL-N-22-00432-00001 0.35 0.49 58 52 25
with Simulated Divided Light PEL-N-22-00433-00001 0.35 0.49 58 52 25
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2015 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
CM-22
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
SOUND TRANSMISSION CLASS
Outdoor-Indoor Transmission Class
(—) = Not Applicable
NOTE: Performance with additional options may not be the same as Standard and Special size units. Please contact your local Pella representative for complete information.
(1) ASTM E 1425 defines standard sizes for acoustical testing. Ratings achieved at that size are representative of all sizes of the same configuration.
(2) Custom glass.
Product Frame Size Tested1
Glazing SystemSTC
RatingOITC
RatingOverall Glazing
Thickness
Exterior Glass
Thickness
Interior Glass
Thickness
Third Pane Thickness
(HGP)
ARCHITECT SERIES CLAD WINDOW
VENT WITH INTEGRAL GRILLES
23" x 59" 11/16" 2.5mm 2.5mm — 28 27
VENT WITH REMOVABLE OR NO GRILLES
23" x 59" 11/16" 2.5mm 2.5mm — 28 25
FIXED WITH INTEGRAL GRILLES
47" x 59" 11/16" 3mm 3mm — 30 27
FIXED WITH REMOVABLE OR NO GRILLS
47" x 59" 11/16" 3mm 3mm — 29 24
ARCHITECT SERIES CLAD WINDOW WITH HURRICANESHIELD ® IMPACT-RESISTANT
VENT WITH REMOVABLE OR NO GRILLES
29" x 53" 9/16" 13.6mm SGP — — 35 32
29" x 53" 9/16" 13.6mm PVB — — 36 32
29" x 53" 11/16" 3mm 7.6mm PVB — 35 30
29" x 53" 1" 5mm 10.1mm SGP — 35 31
29" x 53" 1" 5mm 10.1mm PVB — 34 30
FIXED WITH REMOVABLE OR NO GRILLES
53" x 53" 9/16" 13.6 SGP — — 34 31
53" x 53" 1" 5mm 10.1mm SGP — 35 30
DESIGNER SERIES CLAD WINDOW
VENT – TRIPLE-PANE GLAZING
23"x 59" 5/8" 2.5mm 2.5mm 2.5mm 31 26
23"x 59" 5/8" 6.1mm PVB 2 3mm 3mm 34 30
FIXED – TRIPLE-PANE GLAZING
47"x 59" 5/8" 3mm 3mm 3mm 32 28
PELLA PROLINE CLAD WINDOW
VENT
23" x 59" 11/16" 2.5mm 2.5mm — 27 24
FIXED
47" x 59" 11/16" 3mm 3mm — 27 24
Dual Insulating Glass
Exte
rio
r
Exte
rio
r
Designer Series® Triple-Glazing System
—Third Pane (Hinged
Glass Panel)
Architect Series® Triple Insulating Glass
Exte
rio
r
CM-23
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
COMBINATION ASSEMBLIES
Rectangular Units
Combinations are a great way to create visual interest in any project. A combination is an assembly formed by two or more separate windows or doors whose frames are mulled together by a combination or reinforcing mullion.
Pella window combinations are available in an endless variety of arrangements. Below are available factory-assembled combinations. Some units can be fixed or vent depending on availability, and may vary between Architect Series®, Designer Series® and ProLine®. See Installation and Performance at www.PellaADM.com for typical combinations and requirements and limitations related to mulling various combinations.
Contact your local Pella sales representative for more information.
• Combination Recommendations Downloadable PDF.• Combination Size Tables Downloadable PDF.
Click to view Clad-Wood Combinations Sections
CM-24
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GRILLE TYPES
Typical Grille Profiles
(1) Available in Pine, Mahogany, Alder or Douglas Fir to match complete unit.
(2) Available in Pine or Mahogany to match complete unit.
(3) Putty Exterior/Putty Interior, Ogee Exterior/Putty Interior are also available.
Grilles-Between-the-Glass
Wood Exterior - Wood Interior2, 3 Putty Glaze and Ogee Grilles
7/8"
5/8" 1 1/4"7/8"
5/8" 1 1/4"
Wood Exterior - Wood InteriorOgee and Putty Glaze Grilles
1 1/4"7/8"1 1/4"7/8"
1 1/4"
Integral Light Technology
Wood Exterior - Wood InteriorPutty Glaze Grilles
5/8" 1 1/4"7/8"
5/8" 7/8"
Clad Exterior - Wood InteriorOgee and Putty Glaze Grilles
Clad Exterior - Wood Interior1, 3 Putty Glaze and Ogee Grilles
Clad Exterior - Wood InteriorPutty Glaze Grilles
Wood Exterior - Wood Interior2
Ogee Grilles
Clad Exterior - Wood Interior1
Ogee Grilles
7/8"
1 1/4"7/8"1 1/4"7/8"
5/8" 1 1/4"7/8"
5/8" 1 1/4"
5/8" 1 1/4"7/8"
5/8" 1 1/4"7/8"
7/8" 1 1/4" 2"
2"1 1/4"7/8"
7/8" 1 1/4" 2"
2"1 1/4"7/8"
Wood Exterior - Wood Interior2, 3 Putty Glaze and Ogee Grilles
7/8"
5/8" 1 1/4"7/8"
5/8" 1 1/4"
Wood Exterior - Wood InteriorOgee and Putty Glaze Grilles
1 1/4"7/8"1 1/4"7/8"
1 1/4"
Integral Light Technology
Wood Exterior - Wood InteriorPutty Glaze Grilles
5/8" 1 1/4"7/8"
5/8" 7/8"
Clad Exterior - Wood InteriorOgee and Putty Glaze Grilles
Clad Exterior - Wood Interior1, 3 Putty Glaze and Ogee Grilles
Clad Exterior - Wood InteriorPutty Glaze Grilles
Wood Exterior - Wood Interior2
Ogee Grilles
Clad Exterior - Wood Interior1
Ogee Grilles
7/8"
1 1/4"7/8"1 1/4"7/8"
5/8" 1 1/4"7/8"
5/8" 1 1/4"
5/8" 1 1/4"7/8"
5/8" 1 1/4"7/8"
7/8" 1 1/4" 2"
2"1 1/4"7/8"
7/8" 1 1/4" 2"
2"1 1/4"7/8"
Removable Interior Pine Grilles
3/4"
3/4" Regular
2"1 1/4"2"
2" Regular
1 1/4"
1 1/4" Regular
3/4"
1
2" Colonial1 1/4" Colonial3/4" Regular
Contoured Grille3/4"
3/4"
Contoured Grille3/4"
Contoured Grille3/4"
3/4"
Contoured Grille3/4"
Wood Exterior - Wood Interior2, 3 Putty Glaze and Ogee Grilles
7/8"
5/8" 1 1/4"7/8"
5/8" 1 1/4"
Wood Exterior - Wood InteriorOgee and Putty Glaze Grilles
1 1/4"7/8"1 1/4"7/8"
1 1/4"
Integral Light Technology
Wood Exterior - Wood InteriorPutty Glaze Grilles
5/8" 1 1/4"7/8"
5/8" 7/8"
Clad Exterior - Wood InteriorOgee and Putty Glaze Grilles
Clad Exterior - Wood Interior1, 3 Putty Glaze and Ogee Grilles
Clad Exterior - Wood InteriorPutty Glaze Grilles
Wood Exterior - Wood Interior2
Ogee Grilles
Clad Exterior - Wood Interior1
Ogee Grilles
7/8"
1 1/4"7/8"1 1/4"7/8"
5/8" 1 1/4"7/8"
5/8" 1 1/4"
5/8" 1 1/4"7/8"
5/8" 1 1/4"7/8"
7/8" 1 1/4" 2"
2"1 1/4"7/8"
7/8" 1 1/4" 2"
2"1 1/4"7/8"
Wood Exterior - Wood Interior2, 3 Putty Glaze and Ogee Grilles
7/8"
5/8" 1 1/4"7/8"
5/8" 1 1/4"
Wood Exterior - Wood InteriorOgee and Putty Glaze Grilles
1 1/4"7/8"1 1/4"7/8"
1 1/4"
Integral Light Technology
Wood Exterior - Wood InteriorPutty Glaze Grilles
5/8" 1 1/4"7/8"
5/8" 7/8"
Clad Exterior - Wood InteriorOgee and Putty Glaze Grilles
Clad Exterior - Wood Interior1, 3 Putty Glaze and Ogee Grilles
Clad Exterior - Wood InteriorPutty Glaze Grilles
Wood Exterior - Wood Interior2
Ogee Grilles
Clad Exterior - Wood Interior1
Ogee Grilles
7/8"
1 1/4"7/8"1 1/4"7/8"
5/8" 1 1/4"7/8"
5/8" 1 1/4"
5/8" 1 1/4"7/8"
5/8" 1 1/4"7/8"
7/8" 1 1/4" 2"
2"1 1/4"7/8"
7/8" 1 1/4" 2"
2"1 1/4"7/8"
Integral Light Technology
Rev. 09/02/2015
CM-25
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GRILLE TYPES
Typical Grille Patterns
VG = Visible Glass Lite dimensions noted can vary. Custom configurations are also available, for details contact your local Pella sales representative.
For traditional patterns, see size tables.
Grilles-Between-the-Glass Patterns
PRAIRIE LITE PATTERNS
9-Lite 12-Lite 14-Lite
Integral Light Technology® Grilles and Removable Grille Patterns
PRAIRIE LITE PATTERNS
9-Lite 12-Lite 14-Lite
Size range availability is for 3/4", 7/8" and 1-1/4" grille width. Standard corner lite dimension for Prairie patterns = 2-1/2" VG.
9-Lite
- Available in all standard and special sizes.
12-Lite
- Available in units ≥ 1'9" and ≤ 2'11" in width, and ≥ 1'9" in height.
14-Lite
- Available in units ≥ 1'9" in width and ≥ 2'11" in height .
OTHER AVAILABLE PATTERNS
Cross Top Row
Cross
- Available for units with frame heights ≥35". Standard visible glass to separator bar = 1/4 of total visible glass height.
Top Row
- Standard visible glass to separator bar = 14" for frame heights >35". Standard visible glass to separator bar = 21" for 35" frame heights and optional for 41" frame height. Separator bar at 12" or 16" optional for frame heights >41".
OTHER AVAILABLE PATTERNS
Cross New England Top Row Victorian Simulated French
Cross
- Standard visible glass to separator bar = one-quarter of total visible glass height.
New England
- Standard visible glass to separator bar = half of total visible glass height.
Top Row
- Standard visible glass to separator bar = 14" or half of total visible glass height, whichever is smaller.
CM-26
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
HURRICANESHIELD® IMPACT-RESISTANT
Casement Window
(—) = Not Available
All sizes and glass types are tested for air/water/structural and impact-resistance, and are certified for wind zone 4, large missile rating D.
Florida Product Approval System number not needed if Miami-Dade County approved.
ProductDesign Pressure Large
Missile Rating D Hallmark Certified
Miami-Dade County Approved
Florida Product Approval System
Minimum Maximum
VENT UNITS
9/16" Single-Laminated PVB 75 75 — 14-0811.24 FL10015.2
9/16" Single-Laminated SGP 75 +75 / -85 — 14-0811.24 FL10015.3
11/16" Insulated Glass PVB 75 75 411-H-1339 14-0811.24 FL10015.1
1" Insulated Glass PVB 75 75 411-H-1339 14-0811.24 FL10015.2
1" Insulated Glass SGP 75 +75 / -85 411-H-1339 14-0811.24 FL10015.3
FIXED UNITS
9/16" Single-Laminated PVB 75 75 — 14-0811.25 FL10022.2
9/16" Single-Laminated SGP +75 / -85 +75 / -85 — 14-0811.25 FL10022.4
11/16" Insulated Glass PVB 75 75 411-H-1339 14-0811.25 FL10022.1
1" Insulated Glass PVB 75 75 411-H-1339 14-0811.25 FL10022.2
1" Insulated Glass SGP +75 / -85 +75 / -85 411-H-1339 14-0811.25 FL10022.4
LARGE FIXED UNITS
9/16" Single-Laminated PVB 75 75 — 13-0829.19 FL10022.2
9/16" Single-Laminated SGP 75 +75 / -85 — 13-0829.19 FL10022.4
11/16" Insulated Glass PVB 75 75 411-H-1339 13-0829.19 FL10022.1
1" Insulated Glass PVB 75 75 411-H-1339 13-0829.19 FL10022.2
1" Insulated Glass SGP 75 +75 / -85 411-H-1339 13-0829.19 FL10022.4
For a complete list of the HurricaneShield Impact-Resistant Glazing ratings, refer to the Coastal and High Winds section.
CM-27
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
CASEMENT SHAPES AND OPTIONS
The fol lowing addit ional options are avai lable:
• Wood Types• Grille Types and Patterns• Glazing• Width and height rectangular units• Width sash stiles and rails
• Curved Top Glass in rectangular sash• Shape vent and fixed windows• Corner Window Units (Fixed Only)• Specialty Windows – See the Specialty Windows section
CASEMENT SHAPES (as viewed from the exterior)
Vent or Fixed Shapes
Fixed Shapes Only (see f ixed window section for design parameters)
Double
PitchedIsosceles
Double
PitchedIsosceles
NOTE: Performance Class and Grade for a Casement with additional options and Specialty windows may not be the same as Standard and Special size units. Please contact your local Pella representative for complete information.
CM-28
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DESIGN DATA - CURVED SHAPES
Wood and Aluminum-Clad Wood
Curved Shapes - Fixed Frame cannot exceed 96" in both directions.
For units with colored glazing (bronze, gray or green), frame cannot exceed 11' 0-3/4" in either direction.
Maximum frame < 54.5 ft2 (based on rectangular unit).
Curved Shapes - Roto Operator with Side Pivot HingeMaximum frame size is 19.5 ft2 (based on rectangular unit).
Sash opening will be limited to the angle shown on chart below.
Units will not meet egress requirements.
Frame width cannot exceed hinge jamb height.
Hinge Side Height ≥ Frame Width / 2955 x Frame Area + 18.175" * Calculate Frame Area as if unit was a rectangle. = Frame Height x Frame Width
Unit must be hinged off of short jamb if arc height (Y) divided by arc width (W) is greater than 0.364".
Unit is not valid if arc height (Y) is greater than arc width (W).
Partial units must be true half springlines to vent (R = W).
Custom Stile and Rail WidthsThe A dimension shown can vary from 1-7/8" to 5-3/4".
Any members meeting at an angle not equal to 90� and springline must be the same width.
Bottom rail available with A dimension from 1-7/8" to 9".
AA
WOOD UNITCLAD UNIT
NOTE: Performance Class and Grade for a Casement with additional options and Specialty windows may not be the same as Standard and Special size units. Please contact your local Pella representative for complete information.
SIDE PIVOT CLEAR OPENING FORMULAS
UNIT FRAME WIDTHCLEAR OPENING WIDTH FORMULA
CLAD EXTERIOR WOOD EXTERIOR
13.75" to < 17" (Unit Width x 0.8) - 2.95 (Unit Width x 0.892) - 4.219
17" to < 19" (Unit Width x 0.9) - 4.65 (Unit Width x 0.9) - 4.35
19" to < 25" (Unit Width x 0.883) - 4.433 (Unit Width x 0.883) - 4.133
25" to 29" Unit Width - 5.55 Unit Width - 5.55
> 29" to <= 35" (Unit Width x 0.9) - 4.15 (Unit Width x 0.917) - 4.533
Clear opening height = unit short jamb height - 4.125"
Sash opening will be limited to the angle shown.
Units over 35 inches wide do NOT meet Egress.
RESTRICTED OPENING
Frame Width
Approximate Sash Opening Angle
>35 28 degrees
36 26 degrees
37 25 degrees
38 24 degrees
39 23 degrees
40 22 degrees
41 21 degrees
CM-29
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DESIGN DATA - CURVED SHAPES
Wood and Aluminum-Clad Wood
MINIMUM MAXIMUM RESTRICTIONS
SPRINGLINE Fixed
W 1' 6" 10' 2-5/8"
H 11" 12' 0"
R1 9" 6' 0"
S 2" —
Vent with Side Pivot Hinge
W 1' 6" 3' 5" S ≥ W/2955 x (WxH) + 18.175"
H 2' 3" 8' 0"
R1 9" 1" 8-1/2"
S 1' 1-3/4" —
PARTIAL SPRINGLINE Fixed
W 9" 7" 2-7/8"
H 11" 12' 0"
R1 9" 500"
S 2" —
Vent with Side Pivot Hinge
W 1' 1-3/4" 3' 5" Partial units must be true half springlines to vent.
S ≥ W/2955 x (WxH) + 18.175"
H 2' 3-1/2" 8' 0"
R1 1' 1-3/4" 3' 5"
Hinge Side 1' 1-3/4" FH-Radius
Lock Jamb Side 2' 3-1/2" 8' 0"
ARCH HEAD Fixed
W 9" 12' 0" S ≥ FH - (0.35 x FW). Fixed and Vent Units.
H 9" 12' 0"
R1 9" 500"
S 8" —
Vent with Side Pivot Hinge
W 1' 1-3/4" 3' 5" S ≥ W/2955 x (WxH) + 18.175"
H 1' 2" 8' 0"
R1 9" 500"
S 1' 1-3/4"
PARTIAL ARCH HEAD Fixed
W 9" 12' 0" Side must be less than overall height.Custom stiles and top rail must be the same size, the bottom rail may vary.Width can not exceed 1/2 full arch head.
H 9" 12' 0"
R1 9" 500"
S 8" —
Vent with Side Pivot Hinge
W 1' 1-3/4" 3' 5" S ≥ H - (0.70 x W).Width can not exceed 1/2 full arch head.
S ≥ W/2955 x (WxH) + 18.175"
H 1' 2" 8' 0"
R1 1' 6" —
Hinge Side 1' 1-3/4" —
Lock Jamb Side 1' 1-3/4" —
NOTE: Performance Class and Grade for Casement with additional options and Specialty windows may not be the same as Standard and Special size units. Please contact your local Pella representative for complete information.
CM-30
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DESIGN DATA - ANGLED SHAPES
Wood and Aluminum Clad Wood
MINIMUM MAXIMUM RESTRICTIONS
TRAPEZOID Fixed
W 9" 12' 0" See Restricted Opening.
H 9" 12' 0"
Short Side 1' 1-3/4" —
Vent with Side Pivot Hinge
W 1' 1-3/4" 3' 5" S ≥ W/2955 x (WxH) + 18.175"
(Hinge Side) 1' 1-3/4" 8' 0"
Lock Jamb Side 9" 8' 0"
PENTAGON Fixed
W 9" 12' 0" Peak must be centered. This shape is defined with peak centered for calculation purposes. If peak is not centered, it must be reviewed manually for acceptability.
H 1' 4-13/16" 12' 0"
S1 / S2 9" —
Vent with Side Pivot Hinge
W 1' 1-3/4" 3' 5" See Restricted Opening.
S ≥ W/2955 x (WxH) + 18.175"H 1' 7-9/16" 8' 0"
S1 13-3/4" < 8' 0"
S2 9" —
Angled Shapes - Fixed
Frame cannot exceed 96" in both directions.
Minimum angle between adjoining members is 20°, and maximum angle is < 160°.
Maximum frame < 54.5 ft2 (based on rectangular unit).
Angled Shapes - Roto Operator
Maximum frame area equals 19.5 ft2 (based on rectangular unit).
Not all units meet egress requirements.
Frame width cannot exceed hinge jamb height.
Hinge Side Height ≥ Frame Width / 2955 x Frame Area + 18.175" * Calculate Frame Area as if unit was a rectangle. = Frame Height x Frame Width
Unit must be hinged off short jamb, if angle height (Y) divided by angle width (W) is greater than 0.364.
Unit is not valid if angle height (Y) is greater than angle width (X).
Short Side (S1) must be less than overall height.
Custom Stile and Rail Widths
The A dimension shown can vary from 1-7/8" to 5-3/4".
Any members meeting at an angle not equal to 90o must be the same width.
Bottom rail available with A dimension from 1-7/8" to 1' 3".
V
GENERAL RESTRICTIONS ALL ANGLE TOP
AA
WOOD UNITCLAD UNIT
NOTE: Performance Class and Grade for a Casement with additional options and Specialty windows may not be the same as Standard and Special size units. Please contact your local Pella representative for complete information.
SIDE PIVOT CLEAR OPENING FORMULAS
UNIT FRAME WIDTHCLEAR OPENING WIDTH FORMULA
CLAD EXTERIOR WOOD EXTERIOR
13.75" to < 17" (Unit Width x 0.8) - 2.95 (Unit Width x 0.892) - 4.219
17" to < 19" (Unit Width x 0.9) - 4.65 (Unit Width x 0.9) - 4.35
19" to < 25" (Unit Width x 0.883) - 4.433 (Unit Width x 0.883) - 4.133
25" to 29" Unit Width - 5.55 Unit Width - 5.55
> 29" to <= 35" (Unit Width x 0.9) - 4.15 (Unit Width x 0.917) - 4.533
Clear opening height = unit short jamb height - 4.125"
Sash opening will be limited to the angle shown.
Units over 35 inches wide do NOT meet Egress.
RESTRICTED OPENING
Frame Width
Approximate Sash Opening Angle
>35 28 degrees
36 26 degrees
37 25 degrees
38 24 degrees
39 23 degrees
40 22 degrees
41 21 degrees
CM-31
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DESIGN DATA - RECTANGULAR SHAPES
Wood and Aluminum-Clad Wood
MINIMUM MAXIMUM RESTRICTIONS
RECTANGLE Fixed
H
W
W 10" 144" Maximum Glass weight is 400 Pounds
H 10" 144"
Vent w/Roto Operator (See standard product for Clear Opening formulas)
W 17" 35" Maximum Glass weight is 72 pounds
H 17" 73"
Vent - w/ Roto Operator w/ Side Pivot
W 13-3/4" 35" Maximum Glass weight is 100 pounds.
H 13-3/4" 96"
Vent - w/ Roto Operator w/Side Pivot Restr icted Opening
W 35" 41" Maximum Glass weight is 100 poundsUnits will NOT meet egress requirements.Applies to all vent units with Width (W) > 35"H 35" 96"
Rectangular Units – Fixed
Frame cannot exceed 96" in both directions
For units with colored glazing (bronze, gray or green), frame cannot exceed 11' 0-3/4" in either direction.
Maximum frame < 54.5 ft2
Rectangular Units – Roto Operator with Side Pivot hinge
Maximum frame size is 19.5 ft2 (based on rectangular unit).
Sash openings >35"_ will be limited to the angle shown on the Restricted Opening chart.
Frame width cannot exceed height
Custom Stile and Rail Widths
The A dimension shown can vary from 1-7/8" to 5-3/4".
Any members meeting at an angle not equal to 90° and springline must be the same width.
Bottom rail available with A dimension from 1-7/8" to 9".
AA
WOOD UNITCLAD UNIT
NOTE: Performance Class and Grade for a Casement with additional options and Specialty windows may not be the same as Standard and Special size units. Please contact your local Pella representative for complete information.
SIDE PIVOT CLEAR OPENING FORMULAS
HINGE FRAME WIDTH
FRAME HEIGHT
CLEAR OPENING WIDTH FORMULA
CLAD EXTERIOR WOOD EXTERIOR
STD17" to ≤ 29" 17" to ≤ 73" Unit Width - 4.375 Unit Width - 4.375
> 29" to ≤ 35" 29" to < 47" Unit Width - 4.375 Unit Width - 4.375
HEAVY DUTY*
13.75" to < 17" 13.75" to ≤ 96" (Unit Width x 0.8) - 2.95 (Unit Width x 0.892) - 4.219
17" to < 19" 13.75" to ≤ 96" (Unit Width x 0.9) - 4.65 (Unit Width x 0.9) - 4.35
19" to < 25" 13.75" to ≤ 96" (Unit Width x 0.883) - 4.433 (Unit Width x 0.883) - 4.133
25" to 29" 13.75" to ≤ 96" Unit Width - 5.55 Unit Width - 5.55
> 29" to ≤ 35" 13.75" to ≤ 96" (Unit Width x 0.9) - 4.15 (Unit Width x 0.917) - 4.533
Clear opening height = unit height - 4.125"
* All units with Impact glass or standard IG glass weighing 56 lbs. or more require heavy duty hinges.
Glass Weight Formula: Actual Glass Width (W) x Actual Glass Height (H) x Actual Glass Thickness ÷ 11
Glazing weight in pounds, all Glass Width (W), Height (H) and Thickness are in inches.
Sash opening will be limited to the angle shown.
Units over 35 inches wide do NOT meet Egress.
RESTRICTED OPENING
Frame Width
Approximate Sash Opening Angle
>35 28 degrees
36 26 degrees
37 25 degrees
38 24 degrees
39 23 degrees
40 22 degrees
41 21 degrees
Glass ShapesGLASS SHAPES
CM-32
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
SIZE TABLES
Wood and Aluminum-Clad Wood
Not to scale.
= Fixed Unit Only
Traditional grille patterns shown. Refer to Clad / Wood Overview Section for additional patterns and profiles.
Venting transoms are available as casements or awnings.
Opening Dimensions
CLAD EXTERIOR UNITS: Dimensions shown in tables are rough opening dimensions.
WOOD EXTERIOR UNITS: Use frame dimension plus dimensions below. This dimension includes the use of standard 1-1/8" wood subsill.
FRAME ROUGH MASONRY
Brickmould Width Height Width Height
STD + 3/4" +1-7/8" + 3-1/8" + 3-1/8"
3-1/2" + 3/4" +1-7/8" + 6-3/8" + 4-3/4"
For clad and wood units with HurricaneShield® impact-resistant glass, see the product installation instructions or refer to local building code requirements.
3214
3225
3217
2114 2314 2514 2914 35141714
1717
1725
2117
2125 2325
2317
2525
2517
2925
2917
3525
3517
2121
2323
2929
4"3 /
(813)(832)
2' 8"2' 8
4"3
/
(356
)
1' 2(3
75) 4"
3/
1' 2
"4"
3/
4"3
/4"
3/
4"3
/
Frame
Opening
2' 1
2' 1
"
(654
)(6
35)
2' 5
2' 5
"
(756
)(7
37)
1' 1
11'
11"
(603
)(5
84)
(533
)(5
52)
1' 9
"1'
91'
51'
5"
(451
)(4
32)
4"3 /4"3 /4"3 /4"3 /4"3 /4"3 / 2' 12' 1"
(654)(635)
1' 111' 11"
(603)(584)
1' 91' 9"
(552)(533)
1' 51' 5"
(451)(432) (737)
(756)
2' 5"2' 5
2' 11"2' 11
(908)(889)
F
F
F
F
F
F F
F F
F F F
F F
FFFFF
CM-33
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
SIZE TABLES
Wood and Aluminum-Clad Wood
Not to scale.
(T) = Tempered glass due to aspect ratio.
Traditional grille patterns shown. Refer to Clad / Wood Overview Section for additional patterns and profiles.
Opening Dimensions
CLAD EXTERIOR UNITS: Dimensions shown in tables are rough opening dimensions.
WOOD EXTERIOR UNITS: Use frame dimension plus dimensions below. This dimension includes the use of standard 1-1/8" wood subsill.
FRAME ROUGH MASONRY
Brickmould Width Height Width Height
STD + 3/4" +1-7/8" + 3-1/8" + 3-1/8"
3-1/2" + 3/4" +1-7/8" + 6-3/8" + 4-3/4"
For clad and wood units with HurricaneShield® impact-resistant glass, see the product installation instructions or refer to local building code requirements.3273
3271
3265
3259
3253
3247
3241
32351735 2135 2335
1741 2141 2341
2535 2935
2541 2941 3541
3535
1747 2147 2347 2547 2947 3547
355329532553235321531753
1759 2159 2359 2559 2959 3559
356529652565236521651765
1771 2171 2371 2571 2971 3571
357329732573237321731773
4"3 /
(813)(832)
2' 8"2' 8
Frame
Opening 4"3 /4"3 /4"3 /4"3 /4"3 /4"3 / 2' 12' 1"
(654)(635)
1' 111' 11"
(603)(584)
1' 91' 9"
(552)(533)
1' 51' 5"
(451)(432) (737)
(756)
2' 5"2' 5
2' 11"2' 11
(908)(889)
Vent and Fixed Units
3' 1
13'
11"
(1 2
13)
(1 1
94)
(889
)(9
08)
2' 1
12'
11"
3' 5
3' 5
"
(1 0
60)
(1 0
41)
(1 3
46)
(1 3
65)
4' 5
"4'
5
(1 4
99)
(1 5
18)
4' 1
1"4'
11
5' 5
5' 5
"
(1 6
70)
(1 6
51)
5' 1
15'
11"
(1 8
22)
(1 8
03)
4"3
/4"
3/
4"3
/4"
3/
4"3
/4"
3/
4"3
/
(1 8
54)
(1 8
73)
6' 1
"6'
14"
3/
2E
2E
2E1E
E
E
E
E
E
E
2E E E
EE
EE
E E
E E
E
3E
2E3E
2E
2E
2E
2E
E E
2E
T
T
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
See Design Data pages in this section for clear opening dimensions.
Clear opening (egress) information does not take into consideration the addition of a Rolscreen (or any other accessory) to the product. You should consult your local building code to ensure products with Rolscreens meet egress requirements.
Side pivot hardware reduces Performance class to 'R'.
CM-34
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
SIZE TABLES
Wood and Aluminum-Clad Wood
Not to scale.
Traditional grille patterns shown. Refer to Clad / Wood Overview Section for additional patterns and profiles.
Special Size Frame Dimensions*MINIMUM MAXIMUM
VENT1'5" W x 1'5" H
(432 x 432)
2'11" W x 6'1" H(889 x 1 854)
FIXED1'5" W x 1'5" H
(432 x 432)
4'11" W x 6'1" H(1499 x 1 854)
* Available within size range shown.
Keep frame di men sions to the near est 1/4" increment. Frame width cannot exceed frame height on special size vent units. See the Curved, Angled and Rectangular shapes pages or contact your Pella representative for the availability of custom sizes smaller or larger than the parameters.
Opening Dimensions
CLAD EXTERIOR UNITS: Dimensions shown in tables are rough opening dimensions.
WOOD EXTERIOR UNITS: Use frame dimension plus dimensions below. This dimension includes the use of standard 1-1/8" wood subsill.
FRAME ROUGH MASONRY
Brickmould Width Height Width Height
STD + 3/4" +1-7/8" + 3-1/8" + 3-1/8"
3-1/2" + 3/4" +1-7/8" + 6-3/8" + 4-3/4"
For clad and wood units with HurricaneShield® impact-resistant glass, see the product installation instructions or refer to local building code requirements.
5935533547354135
5973537347734173
Fixed Units
5971
5965
5953
5947
5941
5371
5365
5353
5347
5341
4771
4765
4753
4747
4741
4171
4165
4153
4147
4141
4159 4759 5359 5959
(1 8
54)
(1 8
73)
6' 1
"6'
14"
3/
(889
)(9
08)
2' 1
12'
11"
4"3
/
FrameOpening
3' 1
13'
11"
(1 2
13)
(1 1
94)
3' 5
3' 5
"
(1 0
60)
(1 0
41)
(1 3
46)
(1 3
65)
4' 5
"4'
55'
55'
5"
(1 6
70)
(1 6
51)
5' 1
15'
11"
(1 8
22)
(1 8
03)
4"3
/4"
3/
4"3
/
3' 53' 5"
(1 060)(1 041) (1 194)
(1 213)
3' 113' 11" 4' 11"
4' 11
(1 518)(1 499)(1 346)
(1 365)
4' 5"4' 54"3 / 4"3 / 4"3 / 4"3 /
4"3
/4"
3/
4' 1
14'
11"
(1 5
18)
(1 4
99)
4"3
/
CM-35
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DESIGN DATA
Wood and Aluminum-Clad Wood
(—) = Not Applicable
T = Tempered required due to aspect ratio.
(1) Maximum performance when glazed with the appropriate glass thickness and using standard hinge hardware. Second value, where shown, requires tempered glass.
To convert area to square meters (m²), multiply square feet by 0.0929.
window open 90°.shows vent area withShaded portion
HE
IGH
TO
PE
NIN
GC
LEA
R
w/ side pivot hardware
WIDTHOPENING
CLEAR
WIDTHOPENINGCLEAR
w/ standard hardware
WIDTHOPENING
CLEAR
VENT AREA
opening on 29" units.Sash position for clear
Egress Notes:
Check all applicable local codes for emergency egress require-ments.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
Clear opening (egress) information does not take into consideration the addition of a Rolscreen (or any other accessory) to the product. You should consult your local building code to ensure products with Rolscreens meet egress requirements.
Side pivot hardware reduces Performance class to 'R'.
VENT AND FIXED UNITS
Unit
Egress Clear Opening
Vent Area Ft2
Visible Glass
Ft2
Standard Glass Thickness (mm)
Performance Class & Grade 1
wit
hout
R
ols
cree
n
wit
h R
ols
cree
n
Width (Inches)
Height (Inches)
Ft2
Dual-Pane Glazing
Triple-Pane Glazing
Vent Fixed
Ann
eale
d
Tem
per
ed
Ann
eale
d
or
Tem
per
ed
1735 7-1/4 30-7/8 1.6 2.4 2.3 2.5 3 3 CW50 CW501741 7-1/4 36-7/8 1.9 2.9 2.8 2.5 3 3 CW50 CW501747 7-1/4 42-7/8 2.2 3.4 3.2 2.5 3 3 CW50 CW501753 7-1/4 48-7/8 2.5 3.9 3.7 2.5 3 3 CW50 CW501759 7-1/4 54-7/8 2.8 4.3 4.2 2.5 3 3 CW50 CW501765 7-1/4 60-7/8 3.1 4.8 4.6 2.5 3 3 CW50 CW501771 7-1/4 66-7/8 3.4 5.3 5.1 — 3 3 CW50 CW50T
1773 7-1/4 68-7/8 3.5 5.4 5.3 — 3 3 CW50 CW50T
2135 11-1/4 30-7/8 2.4 3.3 3.1 2.5 3 3 CW50 CW502141 11-1/4 36-7/8 2.9 3.9 3.7 2.5 3 3 CW50 CW502147 11-1/4 42-7/8 3.3 4.6 4.4 2.5 3 3 CW50 CW502153 11-1/4 48-7/8 3.8 5.2 5.0 2.5 3 3 CW50 CW502159 11-1/4 54-7/8 4.3 5.9 5.6 2.5 3 3 CW50 CW502165 11-1/4 60-7/8 4.8 6.5 6.3 2.5 3 3 CW45/CW50 CW45/CW502171 11-1/4 66-7/8 5.2 7.1 6.9 2.5 3 3 CW45/CW50 CW45/CW502173 11-1/4 68-7/8 5.4 7.4 7.1 2.5 3 3 CW40/CW50 CW40/CW502335 13-1/4 30-7/8 2.8 3.7 3.5 2.5 3 3 CW50 CW502341 13-1/4 36-7/8 3.4 4.5 4.2 2.5 3 3 CW50 CW502347 13-1/4 42-7/8 3.9 5.2 4.9 2.5 3 3 CW50 CW502353 13-1/4 48-7/8 4.5 5.9 5.7 2.5 3 3 CW50 CW502359 13-1/4 54-7/8 5.0 6.6 6.4 2.5 3 3 CW45/CW50 CW45/CW502365 13-1/4 60-7/8 5.6 7.4 7.1 2.5 3 3 CW40/CW50 CW40/CW502371 13-1/4 66-7/8 6.2 8.1 7.8 2.5 3 3 CW35/CW50 CW35/CW502373 13-1/4 68-7/8 6.3 8.3 8.1 2.5 3 3 CW35/CW50 CW35/CW502535 15-1/4 30-7/8 3.3 4.2 3.9 2.5 3 3 CW50 CW502541 E3 20-5/8 36-7/8 5.3 5.5 4.7 2.5 3 3 CW50 CW502547 E2 20-5/8 42-7/8 6.1 6.4 5.5 2.5 3 3 CW50 CW502553 E2 20-5/8 48-7/8 7.0 7.3 6.3 2.5 3 3 CW50 CW502559 E2 20-5/8 54-7/8 7.9 8.2 7.1 2.5 3 3 CW45/CW50 CW45/CW502565 E2 20-5/8 60-7/8 8.7 9.1 7.9 2.5 3 3 CW40/CW50 CW40/CW502571 E2 20-5/8 66-7/8 9.6 10.0 8.7 2.5 3 3 CW35/CW50 CW35/CW502573 E2 20-5/8 68-7/8 9.9 10.3 9.0 2.5 3 3 CW30/CW50 CW30/CW502935 E3 24-5/8 30-7/8 5.3 5.5 4.7 2.5 3 3 CW50 CW502941 E2 E2 24-5/8 36-7/8 6.3 6.5 5.7 2.5 3 3 CW50 CW502947 E E2 20 42-7/8 6.0 7.0 6.7 2.5 3 3 CW50 CW502953 E E2 20 48-7/8 6.8 7.9 7.6 2.5 3 3 CW50 CW502959 E E2 20 54-7/8 7.6 8.9 8.6 2.5 3 3 CW45/CW50 CW45/CW502965 E E2 20 60-7/8 8.5 9.9 9.6 2.5 3 3 CW40/CW50 CW40/CW502971 E E2 20 66-7/8 9.3 10.9 10.5 3 3 3 CW45/CW50 CW45/CW502973 E E2 20 68-7/8 9.6 11.2 10.9 3 3 3 CW45/CW50 CW45/CW503235 E2 E3 27-5/8 30-7/8 5.9 6.1 5.3 2.5 3 3 CW50 CW503241 E2 27-5/8 30-7/8 5.9 7.3 6.4 2.5 3 3 CW50 CW503247 E2 E1 27-5/8 36-7/8 7.1 7.9 7.5 2.5 3 3 CW50 CW503253 E E 22-1/4 48-7/8 7.6 9.0 8.6 2.5 3 3 CW45/CW50 CW45/CW503259 E E 22-1/4 54-7/8 8.5 10.1 9.7 2.5 3 3 CW50 CW503265 E E 22-1/4 60-7/8 9.4 11.2 10.8 3 3 3 CW50 CW503271 E E 22-1/4 66-7/8 10.3 12.3 11.9 3 3 3 CW45/CW50 CW45/CW503273 E E 22-1/4 68-7/8 10.6 12.6 12.3 3 3 3 CW45/CW50 CW45/CW503535 E1 E1 25-1/4 30-7/8 5.4 6.3 5.9 2.5 3 3 CW50 CW503541 E E 25-1/4 36-7/8 6.5 7.5 7.2 2.5 3 3 CW50 CW503547 E E 25-1/4 42-7/8 7.5 8.8 8.4 2.5 3 3 CW50 CW503553 E E 25-1/4 48-7/8 8.6 10.0 9.6 2.5 3 3 CW45/CW50 CW45/CW503559 E E 25-1/4 54-7/8 9.6 11.2 10.8 3 3 3 CW50 CW503565 E E 25-1/4 60-7/8 10.7 12.4 12.0 3 3 3 CW50 CW503571 E E 25-1/4 66-7/8 11.7 13.7 13.3 3 3 3 CW45/CW50 CW45/CW503573 E E 25-1/4 68-7/8 12.1 14.1 13.7 3 3 3 CW45/CW50 CW45/CW50
CM-36
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DESIGN DATA
Wood and Aluminum-Clad Wood
VISIBLE GLASS
Width = Frame – 5-3/4"
Height = Frame – 5-3/4"
ACTUAL GLASS
Width = Frame – 4-3/8"
Height = Frame – 4-3/8"
Miscellaneous Formulas
CLEAR OPENING HEIGHT
Frame Height - 4-1/8"
CLEAR OPENING WIDTH
Hinge Frame Width Formula
Standard FW ≥ 29" and ≤ 30-1/2" FW - 9"
Standard FW > 30-1/2" FW - 9-3/4"
Side Pivot FW ≥ 25" and ≤ 35" FW - 4-3/8"
(—) = Not Applicable
F = Fixed only
(1) Maximum performance when glazed with the appropriate glass thickness. Second value, where shown, requires tempered glass.
To convert area to square meters (m²), multiply square feet by 0.0929.
FIXED UNITS
UnitVisible Glass
Ft2
Standard Glass Thickness (mm)
Performance Class & Grade 1
Dual-Pane Glazing
Triple-Pane
Glazing
Ann
eale
d
Tem
per
ed
Ann
eale
d o
r Te
mp
ered
4135 7.2 2.5 3 3 CW504141 8.6 2.5 3 3 CW504147 10.1 3 3 3 CW504153 11.6 3 3 3 CW504159 13.0 3 3 3 CW504165 14.5 3 3 3 CW504171 16.0 3 3 3 CW45/CW504173 16.5 3 3 3 CW45/CW504735 8.4 2.5 3 3 CW504741 10.1 3 3 3 CW504747 11.8 3 3 3 CW504753 13.5 3 3 3 CW504759 15.3 3 3 3 CW504765 17.0 3 3 3 CW45/CW504771 18.7 4 4 4 CW504773 19.3 4 4 4 CW505335 9.6 2.5 3 3 CW45/CW505341 11.6 3 3 3 CW505347 13.5 3 3 3 CW505353 15.5 3 4 4 CW45/CW505359 17.5 4 4 4 CW40/CW505365 19.4 4 4 4 CW505371 21.4 4 4 4 CW505373 22.1 4 4 4 CW505935 10.8 3 3 3 CW505941 13.0 3 3 3 CW505947 15.3 3 3 3 CW505953 17.5 4 4 4 CW40/CW505959 19.7 4 4 4 CW505965 21.9 4 4 4 CW505971 24.1 4 4 4 CW45/CW505973 24.9 4 4 4 CW50
TRANSOM UNITS
Unit
Clear Opening (Inches)
Vent Area Ft2
Visible Glass
Ft2
Standard Glass Thickness (mm)
Performance Class & Grade 1Width Height Ft2
Dual-Pane Glazing
Triple-Pane
Glazing
Ann
eale
d
Tem
per
ed
Ann
eale
d
or
Tem
per
ed
1714F — — — — 0.6 2.5 3 3 CW50
1717 7-1/4 12-7/8 0.6 1.0 0.9 2.5 3 3 CW50
1725F — — — — 1.5 2.5 3 3 CW50
2114F — — — — 0.9 2.5 3 3 CW50
2117F — — — — 1.2 2.5 3 3 CW50
2121 11-1/4 16-7/8 1.3 1.8 1.6 2.5 3 3 CW50
2125F — — — — 2.0 2.5 3 3 CW50
2314F — — — — 1.0 2.5 3 3 CW50
2317F — — — — 1.3 2.5 3 3 CW50
2323 13-1/4 18-7/8 1.7 2.3 2.1 2.5 3 3 CW50
2325F — — — — 2.3 2.5 3 3 CW50
2514F — — — — 1.1 2.5 3 3 CW50
2517F — — — — 1.5 2.5 3 3 CW50
2525 15-1/4 20-7/8 2.2 2.8 2.6 2.5 3 3 CW50
2914F — — — — 1.3 2.5 3 3 CW50
2917F — — — — 1.8 2.5 3 3 CW50
2925F — — — — 3.1 2.5 3 3 CW50
2929 20 24-7/8 3.5 4.0 3.8 2.5 3 3 CW50
3214F — — — — 1.5 2.5 3 3 CW50
3217F — — — — 2.1 2.5 3 3 CW50
3225F — — — — 3.5 2.5 3 3 CW50
3514F — — — — 1.7 2.5 3 3 CW50
3517F — — — — 2.3 2.5 3 3 CW50
3525F — — — — 3.9 2.5 3 3 CW50
For units with FW >35" reference degree opening chart.
Rev. 05/13/2015
CM-37
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DETAILED PRODUCT DESCRIPTIONS
Aluminum-Clad Wood
FRAME • Select softwood, immersion treated with Pella’s EnduraGuard® wood protection
formula in accordance with WDMA I.S.-4. The EnduraGuard formula includes three active ingredients for protection against the effects of moisture, decay, stains from mold and mildew. Plus, an additional ingredient adds protection against termite damage.
• Interior exposed surfaces are [pine] [mahogany] [alder] [douglas fir] (standard rectangular units only). Any curved member may have visible finger-jointed surfaces.
• Exterior surfaces are clad with aluminum. • Overall frame depth is 5" (127mm) for a wall depth of 3-11/16" (94mm).• Optional factory-applied jamb extensions available between 4-9/16"
(116mm) and 7-3/16" (183mm) wall depths.• Optional factory-installed fold-out installation fins with flexible fin corners.• Optional factory-applied EnduraClad® exterior trim.
SASH• Select softwood, immersion treated with Pella’s EnduraGuard® wood protection
formula in accordance with WDMA I.S.-4. The EnduraGuard formula includes three active ingredients for protection against the effects of moisture, decay, stains from mold and mildew. Plus, an additional ingredient adds protection against termite damage.
• Interior exposed surfaces are clear [pine] [mahogany] [alder] [douglas fir] (standard rectangular units only). Any curved member may have visible finger-jointed surfaces.
• Exterior surfaces are clad with aluminum, lap-jointed and sealed. • Corners mortised and tenoned, glued and secured with metal fasteners. • Sash thickness is [1-13/16" (46mm) for 11/16"] [1-11/16" (43mm) for 9/16"]
[2-1/8" (54mm) for 1"] glazing.
WEATHERSTRIPPING• Dual weatherstripping.
� Flexible santoprene material compressed between frame and sash for positive seal on all four sides.
� Secondary thermoplastic vulcanizate (TPV) leaf-type weatherstrip between edge of sash and frame.
GLAZING SYSTEM 1• Quality float glass complying with ASTM C 1036.• Silicone-glazed 11/16" dual-seal insulating glass [[annealed] [tempered]] [[clear]
[Advanced Low-E with Argon] [SunDefense™ Low-E with Argon] [NaturalSun Low-E with Argon] [AdvancedComfort Low-E coated with argon]] [[bronze] [gray] [green] Advanced Low-E coated with Argon]].
• Custom and high altitude [with argon] glazing available for 11/16" glazing only. – or –
• Silicone-glazed 1" triple-seal insulating glass [[annealed] [tempered]] [[Advanced Low-E with argon] [Advanced Low-E with krypton] [SunDefense™ Low-E with argon] [SunDefense™ Low-E with krypton] [NaturalSun Low-E with argon] [NaturalSun Low-E with krypton]].
– or –• Impact-Resistant
� Silicone-glazed 1" dual-seal impact-resistant insulating glass 1 [PVB] [SGP]. [[tempered] [annealed]] exterior light is [[Advanced Low-E coated with argon] [clear] [bronze] [gray] [green]]. Laminated clear interior light.
– or – � Silicone-glazed 11/16" dual-seal impact-resistant insulating glass 1 [PVB].
[[tempered] [annealed]] exterior light is [[Advanced Low-E coated with argon] [clear]]. Laminated [clear] interior light, or [[tempered] [annealed]] exterior light is [[Advanced Low-E coated with argon] [clear]]. Laminated [[bronze] [gray] [green]] interior light.
– or – � Silicone-glazed 9/16" [PVB] laminated glass [[clear] [bronze] [gray] [green]].
– or – � Silicone-glazed 9/16" [SGP] laminated glass [[clear] [multi-layer Low-E]
[bronze] [gray] [green]].
EXTERIOR• Aluminum clad exteriors shall be finished with EnduraClad® protective finish, in
a multi-step, baked-on finish.• Color is [White] [Tan] [Brown] [Putty] [feature 2] [custom 2].
– or –• Aluminum clad exteriors shall be finished with EnduraClad Plus protective finish
with 70% fluoropolymer resin in a multi-step, baked-on finish • Color is [White] [Tan] [Brown] [Putty] [feature 2] [custom 2].
INTERIOR• [Unfinished, ready for site finishing] [factory primed with one coat acrylic latex]
[factory prefinished [White] [Linen White] [Bright White] [stain 2]].
HARDWARE • Roto operator assembly
� Steel worm gear sash operator with hardened gears. � Operator base is zinc die cast with painted finish. � Operator linkage, hinge slide, and hinge arms are stainless steel. � Exposed fasteners are stainless steel. � Hardware shall exceed 1,000 hours salt spray exposure per ASTM B 117.
• Finish of integrated fold-away crank is [[baked enamel [Champagne] [White] [Brown]] [Bright Brass] [Satin Nickel] [Oil-Rubbed Bronze]. All vent units are available with left- or right-hand hinging.
• SureLock® System—A single handle locking system operates positive-acting arms that reach out and pull the sash into a locked position: one unison operating lock installed on units with frame height 29" and smaller, two installed on units with frame height greater than 29".
• Lock handle finish is [baked enamel, champagne] [baked enamel, White] [baked enamel, Brown] [Bright Brass] [Satin Nickel] [Oil-Rubbed Bronze].
OPTIONAL PRODUCTSGrilles• Integral Light Technology® grilles
� Interior grilles are [5/8" [putty] [ogee] profile] [7/8" [putty] [ogee] profile] [1-1/4" [putty] [ogee] profile] [2" ogee profile] that are solid [Pine] [Mahogany] [Alder] [Douglas Fir]. Interior surfaces are [unfinished, ready for site finishing] [factory primed] [pine: factory prefinished [White] [Linen White] [Bright White] [stain 2]].
� Exterior grilles are [5/8" putty profile] [7/8" [putty] [ogee] profile] [1-1/4" [putty] [ogee] profile] [2" ogee profile] that are extruded aluminum to match window cladding.
� Patterns are [Traditional] [Prairie] [Top Row] [Cross] [New England] [Victorian] [Simulated French].
� Insulating glass contains non-glare spacer between the panes of glass. � Grilles are adhered to both sides of the insulating glass with VHB acrylic
adhesive tape and aligned with the non-glare spacer.– or –
• Grilles-Between-the-Glass 3 � Insulating glass contains 3/4" contoured aluminum grilles permanently
installed between two panes of glass (exterior air-space on triple-pane insulating glass).
� Patterns are [Traditional] [Prairie] [Cross] [Top Row] [Custom – Equally Divided].
� Interior color is [White] [Tan 4] [Brown 4] [Putty 4] [Ivory] [Brickstone] [Harvest] [Cordovan].
� Exterior color 5 is [White] [Tan] [Brown] [Putty] [feature 2].– or –
• Removable Grilles � [[3/4"] [1-1/4"] [2"] Regular] [[1-1/4"] [2"] Colonial] profile, with [Traditional]
[Prairie] patterns that are removable solid pine wood bars steel-pinned at joints and fitted to sash with steel clips and tacks.
� Interior [unfinished, ready for site finishing] [factory primed] [pine: factory prefinished [White] [Linen White] [Bright White] [stain 2]].
� Exterior [unfinished, ready for site finishing] [Factory Primed] [finish color matched to exterior cladding 5].
Screens• InView™ Screens
� Vinyl-coated 18/18 mesh fiberglass screen cloth complying with SMA 1201, set in aluminum frame fitted to inside of window, supplied complete with all necessary hardware.
� Screen frame finish is baked enamel, [Champagne] [White] [Brown].– or –
• Vivid View® Screens � PVDF 21/17 mesh, minimum 78 percent light transmissive screen, set in
aluminum frame fitted to inside of window, supplied complete with all necessary hardware.
� Screen frame finish is baked enamel, [Champagne] [White] [Brown].– or –
• Rolscreen® Retractable Screen (for rectangular units only) � Self-storing, rolling, black vinyl-coated 18/16 mesh fiberglass screen cloth
complying with ASTM D 3656 and SMA 1201 mounted behind overhead cover.
� Cover finish is [factory prefinished paint] [[pine] [mahogany] [alder] [douglas fir] veneer wrapped over extruded aluminum with factory prefinished [stain 2] [paint 2]].
� Guides are aluminum extrusion with [[pine] [mahogany] veneer wrapped over extruded aluminum with factory prefinished [stain 2] [paint 2]].
Hardware• Optional factory applied limited opening hardware available for vent units in
stainless steel; nominal 3" opening.• Optional window opening control device available for field installation. Device
allows window to open less than 4" with normal operation, with a release mechanism that allows the sash to open completely. Complies with ASTM F2090-10.
(1) Insulating glass with argon is Low-E coated (except high altitude). All other insulating glass (including high altitude Low-E) is air-filled. (2) Contact your local Pella sales representative for current color options. (3) Available in clear or Low-E insulating glass only. White exterior grille color is the only option available for clear insulating glass. (4) Tan, Brown and Putty Interior GBG colors are available in single-tone (Brown/Brown, Tan/Tan or Putty/Putty). Other interior colors are also available with tan or brown exterior. (5) Appearance of exterior grille color will vary depending on Low-E coating on glass.
Rev. 07/13/2015
CM-38
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DETAILED PRODUCT DESCRIPTIONS
Wood Exterior
(1) Insulating glass with argon is Low-E coated. All other insulating glass is air-filled.
(2) Available in clear or Low-E insulating glass only with argon, clear insulated glass and obscure insulated glass. White exterior grille color and traditional patterns are the only options available for clear insulating glass.
(3) Contact your local Pella sales representative for current color options.
(4) Tan, Brown or Putty Interior GBG colors are available in single-tone (Brown/Brown, Tan/Tan or Putty/Putty). Other interior colors are also available with Tan or Brown exterior.
FRAME
• Select softwood, immersion treated with Pella’s EnduraGuard® wood protection formula in accordance with WDMA I.S.-4. The EnduraGuard formula includes three active ingredients for protection against the effects of moisture, decay, stains from mold and mildew. Plus, an additional ingredient adds protection against termite damage.
• Interior exposed surfaces are [pine] [mahogany] (standard rectangular windows only). Any curved member may have visible finger-jointed surfaces.
• Exterior surfaces are [pine: Factory Primed] [mahogany: [factory primed] [ready-to-stain]].
• Overall frame depth is 4-3/8" (111mm) for a wall depth of 4-3/16" (106mm).• Optional factory-applied jamb extensions available between 4-9/16"
(116mm) and 7-3/16" (183mm) wall depths, with Pella’s standard wood exterior trim.
SASH
• Select softwood, immersion treated with Pella’s EnduraGuard® wood protection formula in accordance with WDMA I.S.-4. The EnduraGuard formula includes three active ingredients for protection against the effects of moisture, decay, stains from mold and mildew. Plus, an additional ingredient adds protection against termite damage.
• Interior exposed surfaces are [pine] [mahogany] (standard rectangular windows only). Any curved member may have visible finger-jointed surfaces.
• Exterior surfaces are [pine: Factory Primed] [mahogany: [factory primed] [ready-to-stain]].
• Corners mortised and tenoned, glued and secured with metal fasteners. • Sash thickness is 1-13/16" (46mm).
WEATHERSTRIPPING
• Dual weatherstripping. � Flexible santoprene material compressed between frame and sash for
positive seal on all four sides. � Secondary thermoplastic vulcanizate (TPV) leaf-type weatherstrip
between edge of sash and frame.
GLAZING SYSTEM 1
• Quality float glass complying with ASTM C 1036.• Silicone-glazed 11/16" dual-seal insulating glass [[annealed] [tempered]]
[[clear] [Advanced Low-E with argon] [SunDefense™ Low-E with argon] [AdvancedComfort Low-E with argon] [NaturalSun Low-E with Argon]] [[bronze] [gray] [green] Advanced Low-E with argon]].
• Custom and high altitude [with argon] glazing available.– or –
• Silicone-glazed 1" triple-seal insulating glass [[annealed] [tempered]] [[Advanced Low-E with argon] [Advanced Low-E with krypton] [SunDefense™ Low-E with argon] [SunDefense™ Low-E with krypton] [NaturalSun Low-E with argon] [NaturalSun Low-E with krypton]].
INTERIOR
• [Unfinished, ready for site finishing] [factory primed with one coat acrylic latex] [factory prefinished [White] [Linen White] [Bright White] [stain 3]].
HARDWARE
• Roto operator assembly � Steel worm gear sash operator with hardened gears. � Operator base is zinc die cast with painted finish. � Operator linkage, hinge slide, and hinge arms are stainless steel. � Exposed fasteners are stainless steel. � Hardware will exceed 1,000 hours salt spray exposure per ASTM B 117.
• Finish of integrated fold-away crank is [[baked enamel [Champagne] [White] [Brown]] [Bright Brass] [Satin Nickel] [Oil-Rubbed Bronze]. All vent units are available with left- or right-hand hinging.
• SureLock® System—A single handle locking system operates positive-acting arms that reach out and pull the sash into a locked position: one unison operating lock installed on units with frame height 29" and smaller, two installed on units with frame height greater than 29".
• Lock handle finish is [[baked enamel [Champagne] [White] [Brown]] [Bright Brass] [Satin Nickel] [Oil-Rubbed Bronze].
OPTIONAL PRODUCTS
Grilles• Integral Light Technology® grilles
� Interior grilles are solid [5/8" [putty] [ogee] profile] [7/8" [putty] [ogee] profile] [1-1/4" [putty] [ogee] profile] [2" ogee profile] that are solid [pine] [mahogany]. Interior surfaces are [unfinished, ready for site finishing] [factory primed] [pine: factory prefinished [White] [Linen White] [Bright White] [stain 3]].
� Exterior grilles are solid [5/8" putty profile] [7/8" [putty] [ogee] profile] [1-1/4" [putty] [ogee] profile] [2" ogee profile] that are [pine] [mahogany]. Exterior surfaces are water repellent, preservative-treated in accordance with WDMA I.S.-4, and are [unfinished, ready for site finishing] [factory primed].
� Patterns are [Traditional] [Prairie] [Top Row] [Cross] [New England] [Victorian] [Simulated French].
� Insulating glass contains non-glare spacer between the panes of glass. � Grilles are adhered to both sides of the insulating glass with VHB acrylic
adhesive tape and aligned with the non-glare spacer.– or –
• Grilles-Between-the-Glass2 � Insulating glass contains 3/4" contoured aluminum grilles permanently
installed between two panes of glass (exterior air-space on triple-pane insulating glass).
� Patterns are [Traditional] [Prairie] [Cross] [Top Row] [Custom – Equally Divided].
� Interior color is [White] [Tan 4] [Brown 4] [Putty 4] [Ivory] [Brickstone] [Harvest] [Cordovan].
� Exterior color is [White] [Tan] [Brown] [Putty] [feature 3].– or –
• Removable Grilles � [[3/4"] [1-1/4"] [2"] Regular] [[1-1/4"] [2"] profile, with [Traditional]
[Prairie] patterns that are removable solid pine wood grilles steel-pinned at joints and fitted to sash with steel clips and tacks.
� Interior [unfinished, ready for site finishing] [factory primed] [pine: factory prefinished [White] [Linen White] [Bright White] [stain 3]].
� Exterior [unfinished, ready for site finishing] [Factory Primed] [finish color matched to exterior cladding].
� When the unit exterior is mahogany then removable grilles is not an option.
Screens• InView™ Screens
� Vinyl-coated 18/18 mesh fiberglass screen cloth complying with SMA 1201, set in aluminum frame fitted to inside of window, supplied complete with all necessary hardware.
� Screen frame finish is baked enamel, [Champagne] [White] [Brown].– or –
• Vivid View® Screens � PVDF 21/17 mesh, minimum 78 percent light transmissive screen, set in
aluminum frame fitted to inside of window, supplied complete with all necessary hardware.
� Screen frame finish is baked enamel, [Champagne] [White] [Brown].– or –
• Rolscreen® Retractable Screen (for rectangular units only) � Self-storing, rolling, black vinyl-coated 18 / 16 mesh fiberglass screen
cloth complying with ASTM D 3656 and SMA 1201 mounted behind overhead cover.
� Cover finish is [factory prefinished paint] [[pine] [mahogany] veneer wrapped over extruded aluminum with factory prefinished [stain 3] [paint 3]].
� Guides are aluminum extrusion with [[pine] [mahogany] veneer wrapped over extruded aluminum with factory prefinished [stain 3] [paint 3]].
Hardware• Optional factory applied limited opening hardware available for vent units in
stainless steel; nominal 3" opening.• Optional window opening control device available for field installation.
Device allows window to open less than 4" with normal operation, with a release mechanism that allows the sash to open completely. Complies with ASTM F2090-10.
Rev. 07/13/2015
CM-39
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
Alder or Douglas Fir Interior Pine or Mahogany Interior
Not to Scale
UNIT SECTIONS — WOOD COLLECTION
Aluminum-Clad Wood
JAMBS
SILL
HEAD
Solid Mahogany or Pine
Solid Pine
Alder or Douglas Fir
JAMBS
SILL
HEAD
CM-40
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
UNIT SECTIONS
Aluminum-Clad Wood
Scale 3" = 1' 0"
All dimensions are approximate.
[46]
1 13
/16"[46]
1 13/16"
[46]1 13/16"
[46]
1 13
/16"
TRANSOM / VENTHORIZONTAL JOINING MULLION
VENT / FIXEDVERTICAL JOINING MULLION
VENT / VENTVERTICAL JOINING MULLION
FRAME WIDTH
[47]1 7/8"
[19]3/4"
[73]2 7/8"
[33]
1 5/
16"
[94]
3 11
/16"
Installation FinOptional Fold-out
FRA
ME
HE
IGH
T
[70]
2 3/
4"[1
9]3/
4"[4
7]1
7/8"
FRAME WIDTH
FRA
ME
HE
IGH
T
[47]1 7/8"
[19]3/4"
[73]2 7/8"
[72]
2 7/
8"[1
9]3/
4"[4
8]1
7/8"
[19]3/4"
[19]
3/4"
[19]3/4"
[33]
1 5/
16"
[94]
3 11
/16"
[127]5"
Installation FinOptional Fold-out
VENT
FIXED
LJ HJ
FS
FH
VH
VS
FJ
LOCK JAMBLJ HINGE JAMBHJ
FS FIXED SILL
FH FIXED HEAD
FJ FIXED JAMB
VH VENT HEAD
VS VENT SILL
CM-41
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
Scale 3" = 1' 0"
See Installation and Performance at www.PellaADM.com for mullion limitations and reinforcing requirements.
[46]
1 13
/16"
[46]1 13/16"
®
INSECT SCREENROLSCREENVENT WITH
FRA
ME
HE
IGH
T
[72]
2 7/
8"[1
9]3/
4"[4
7]1
7/8"
[127]5"
FRAME WIDTH
[33]
1 5/
16"
[94]
3 11
/16"
Installation FinOptional Fold-out
[19]3/4"
[73]2 7/8"
[19]3/4"
[47]1 7/8"
VENT
LJ HJ
VH
VS
LOCK JAMBLJ HINGE JAMBHJ
VH VENT HEAD
VS VENT SILL
UNIT SECTIONS
Aluminum-Clad Wood
CM-42
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
UNIT SECTIONS
Wood Exterior
Scale 3" = 1' 0"
All dimensions are approximate.
[46]
1 13
/16"
[46]
1 13
/16"
[46]1 13/16"
[73]
2 7/
8"
FRA
ME
HE
IGH
T
FIXED
[138]5 7/16"
[28]
1 1/
16"
[46]
1 13
/16" [47]
1 7/8"[19]3/4"
[73]2 7/8"
FRAME WIDTH
[19]3/4"
[30]1 3/16"
[30]1 3/16"
[29]
1 1/
8"[1
06]
4 3/
16"
[19]
3/4"
[47]
1 7/
8"
[111]4 3/8"
[73]
2 7/
8"
FRA
ME
HE
IGH
T
[138]5 7/16"
[28]
1 1/
16"
[46]
1 13
/16"
Shown1-1/8" Subsill #3544
1-78" Brickmould #3443
[47]1 7/8"
[19]3/4"
[73]2 7/8"
FRAME WIDTH
[19]3/4"
[30]1 3/16"
[30]1 3/16"
[19]3/4"
[29]
1 1/
8"[1
06]
4 3/
16"
VENT / VENTVERTICAL JOINING MULLION
FIXED / VENTHORIZONTAL JOINING MULLION
VENT / FIXEDVERTICAL JOINING MULLION
[19]
3/4"
[47]
1 7/
8"
[111]4 3/8"
VENT
FS
FH
FJ
HJLJ
VH
VS
FS FIXED SILL
FH FIXED HEAD
FJ FIXED JAMB
LOCK JAMBLJ HINGE JAMBHJ
VH VENT HEAD
VS VENT SILL
CM-43
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
UNIT SECTIONS
Wood Exterior
Rolscreen Retractable Screen
[46]
1 13
/16"
[46]1 13/16"
[73]
2 7/
8"
FRA
ME
HE
IGH
T
[138]5 7/16"
[28]
1 1/
16"
[46]
1 13
/16"
Shown1-1/8" Subsill #3544
1-78" Brickmould #3443
[47]1 7/8"
[19]3/4"
[73]2 7/8"
FRAME WIDTH
[19]3/4"
[30]1 3/16"
[30]1 3/16"
[19]3/4"
[29]
1 1/
8"[1
06]
4 3/
16"
[19]
3/4"
[47]
1 7/
8"
[111]4 3/8"
VENT
[47]
1 7/
8"
[138]5 7/16"
[71]
2 13
/16"
[71]
2 13
/16"
[30]
1 3/
16"
1-7/8" SUBSILLOPTIONAL
1-1/8" SUBSILLOPTIONAL
CASING3-1/2" FLAT
BRICKMOULD3-1/2"
BRICKMOULD1-7/8"
[28]
1 1/
8"
[29]1 1/8"
[138]5 7/16"
[29]1 1/8"
[89]
3 1/
2"
[29]1 1/8"
[89]
3 1/
2"
[48]
1 7/
8"
HJLJ
VH
VS
LOCK JAMBLJ HINGE JAMBHJ
VH VENT HEAD
VS VENT SILL
Scale 3" = 1' 0"
All dimensions are approximate.
CM-44
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GRILLE TYPESRemovable Between-Glass
VG = Visible Glass
Lite dimensions noted can vary.
Custom configurations are also available, for details contact your local Pella sales representative.
For size and pattern availability; contact your local Pella sales representative.
For traditional patterns, see size tables.
Removable Grilles-Between-the-Glass
PRAIRIE LITE PATTERNS
VG
VG
VG
VG
VG
VG
VG
VG
VG
VG
Top RowNew EnglandCross
14-Lite12-Lite9-Lite9-Lite
VG
VG
VG
VG
VG
VG
VG
VG
VG
VG
Top RowNew EnglandCross
14-Lite12-Lite9-Lite12-Lite
VG
VG
VG
VG
VG
VG
VG
VG
VG
VG
Top RowNew EnglandCross
14-Lite12-Lite9-Lite14-Lite
Standard corner lite dimension for Prairie patterns = 2-1/2" VG.
9-Lite
- Available in all standard and special sizes.
12-Lite
- Available in units ≥ 2'0" in width and ≥ 2'0" in height.
14-Lite
- Available in units ≥ 2'0" in width and ≥ 3'0" in height .
OTHER AVAILABLE PATTERNS
VG
VG
VG
VG
VG
VG
VG
VG
VG
VG
Top RowNew EnglandCross
14-Lite12-Lite9-Lite
Cross
VG
VG
VG
VG
VG
VG
VG
VG
VG
VG
Top RowNew EnglandCross
14-Lite12-Lite9-Lite
New England
VG
VG
VG
VG
VG
VG
VG
VG
VG
VG
Top RowNew EnglandCross
14-Lite12-Lite9-Lite
Top Row
Cross
- Standard visible glass to separator bar = one-quarter of total visible glass height.
New England
- Standard visible glass to separator bar = half of total visible glass height.
Top Row
- Standard visible glass to separator bar = 14" or half of total visible glass height, whichever is smaller.
Grille Profiles
Removable Grilles Between-the-Glass
3/4" Triple-Pane with Slimshade Blind
3/4" Triple-Pane with Cellular Fabric Shade
Grille Patterns
CM-45
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
SIZE TABLES
Aluminum-Clad Wood
Not to scale. * Available within size range shown
Fixed units only.
T Tempered glass is standard.
Traditional grille patterns shown. Refer to Clad / Wood Overview Section for additional patterns and profiles.
Vent transoms are available as casements or awnings.
Special Size Frame Dimensions*
MINIMUM MAXIMUM
VENT1'5" W x 1'5" H
(432 x 432)
2'11" W x 6'1" H(889 x 1 854)
FIXED1'5" W x 1'5" H
(432 x 432)
4'11" W x 6'1" H(1499 x 1 854)
3217
3225
3241
3235
3247
3253
3259
3265
3271
3273
21171717
2121
2317 2517 2917 3517
2323
1725 2125 2325 2525 2925 3525
2929
1735 2135 2335
1741 2141 2341
2535 2935
2541 2941 3541
3535
1747 2147 2347 2547 2947 3547
355329532553235321531753
1759 2159 2359 2559 2959 3559
356529652565236521651765
1771 2171 2371 2571 2971 3571
357329732573237321731773
4"3 /
(813)(832)
2' 8"2' 8
Transoms
Vent and Fixed Units
(889)(908)
2' 112' 11"
2' 52' 5"
(756)(737)(432)
(451)
1' 5"1' 5
(533)(552)
1' 9"1' 9
(584)(603)
1' 11"1' 11
(635)(654)
2' 1"2' 1
3' 1
13'
11"
(1 2
13)
(1 1
94)
(432
)(4
51)
1' 5
"1'
51'
91'
9"
(552
)(5
33)
(584
)(6
03)
1' 1
1"1'
11
(737
)(7
56)
2' 5
"2'
5
(889
)(9
08)
2' 1
12'
11"
(635
)(6
54)
2' 1
"2'
13'
53'
5"
(1 0
60)
(1 0
41)
(1 3
46)
(1 3
65)
4' 5
"4'
5
(1 4
99)
(1 5
18)
4' 1
1"4'
11
5' 5
5' 5
"
(1 6
70)
(1 6
51)
5' 1
15'
11"
(1 8
22)
(1 8
03)
4"3 / 4"3 / 4"3 / 4"3 / 4"3 / 4"3 /OpeningFrame
4"3
/4"
3/
4"3
/4"
3/
4"3
/4"
3/
4"3
/4"
3/
4"3
/4"
3/
4"3
/4"
3/
(1 8
54)
(1 8
73)
6' 1
"6'
14"
3/
2E1E
F
F
E
E
2E
E
E
E
E
2E
2E
T
T
T EE
EE
2E
2E
2E
2E
3E 2E
3E 1E
E
EE
EE
EE
E E
FFFFF
FFFFF
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
See Design Data pages in this section for clear opening dimensions.
Clear opening (egress) information does not take into consideration the addition of a Rolscreen (or any other accessory) to the product.
You should consult your local building code to ensure products with Rolscreens meet egress requirements.
CM-46
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
SIZE TABLES
Aluminum-Clad Wood
Not to scale.
Traditional grille patterns shown. Refer to Clad / Wood Overview Section for additional patterns and profiles.
537347734173 5973
5971537147714171
4165 4765 5365 5965
5959535947594159
4153 4753 5353 5953
5947534747474147
4141 4741 5341 5941
5935533547354135
OpeningFrame
(1 8
54)
(1 8
73)
6' 1
"6'
14"
3/
5' 1
15'
11"
(1 8
22)
(1 8
03) 4"
3/
5' 5
5' 5
"
(1 6
70)
(1 6
51) 4"
3/
(1 4
99)
(1 5
18)
4' 1
1"4'
11
4"3
/
(1 3
46)
(1 3
65)
4' 5
"4'
54"
3/
3' 1
13'
11"
(1 2
13)
(1 1
94) 4"
3/
3' 5
3' 5
"
(1 0
60)
(1 0
41) 4"
3/
(889
)(9
08)
2' 1
12'
11"
4"3
/
Fixed Units
3' 53' 5"
(1 060)(1 041) (1 194)
(1 213)
3' 113' 11" 4' 11"
4' 11
(1 518)(1 499)(1 346)
(1 365)
4' 5"4' 54"3 / 4"3 / 4"3 / 4"3 /
CM-47
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DESIGN DATA
Aluminum-Clad Wood
VENT AND FIXED UNITS
Unit
Egress Clear OpeningVent Area Ft2
Visible Glass
Ft2
Standard Glass Thickness (mm)
Performance Class & Grade1
wit
hout
R
ols
cree
n
wit
h
Ro
lscr
een
Width (Inches)
Height (Inches)
Ft2
Ann
eale
d
Tem
per
ed
1735 7-1/4 30-7/8 1.6 2.4 2.1 2.5 3 R501741 7-1/4 36-7/8 1.9 2.8 2.5 2.5 3 R501747 7-1/4 42-7/8 2.2 3.3 3.0 2.5 3 R501753 7-1/4 48-7/8 2.5 3.7 3.4 2.5 3 R501759 7-1/4 54-7/8 2.8 4.2 3.8 2.5 3 R501765T 7-1/4 60-7/8 3.1 4.7 4.3 — 3 R501771T 7-1/4 66-7/8 3.4 5.1 4.7 — 3 R501773T 7-1/4 68-7/8 3.5 5.3 4.8 — 3 R502135 11-1/4 30-7/8 2.4 3.2 2.9 2.5 3 R502141 11-1/4 36-7/8 2.9 3.8 3.5 2.5 3 R45/R502147 11-1/4 42-7/8 3.3 4.5 4.1 2.5 3 R40/R502153 11-1/4 48-7/8 3.8 5.1 4.7 2.5 3 R35/R502159 11-1/4 54-7/8 4.3 5.7 5.3 2.5 3 R30/R502165 11-1/4 60-7/8 4.8 6.3 5.9 2.5 3 R30/R502171 11-1/4 66-7/8 5.2 7.0 6.5 2.5 3 R30/R502173 11-1/4 68-7/8 5.4 7.2 6.7 2.5 3 R30/R502335 13-1/4 30-7/8 2.8 3.7 3.3 2.5 3 R502341 13-1/4 36-7/8 3.4 4.4 4.0 2.5 3 R45/R502347 13-1/4 42-7/8 3.9 5.1 4.6 2.5 3 R35/R502353 13-1/4 48-7/8 4.5 5.8 5.3 2.5 3 R30/R502359 13-1/4 54-7/8 5.0 6.5 6.0 2.5 3 R25/R502365 13-1/4 60-7/8 5.6 7.2 6.7 2.5 3 R25/R502371 13-1/4 66-7/8 6.2 7.9 7.4 2.5 3 R20/R502373 13-1/4 68-7/8 6.3 8.1 7.6 2.5 3 R20/R502535 15-1/4 30-7/8 3.3 4.1 3.7 2.5 3 R502541 E3 20-5/8 36-7/8 5.3 5.5 4.4 2.5 3 R45/R502547 E2 20-5/8 42-7/8 6.1 6.3 5.2 2.5 3 R35/R502553 E2 20-5/8 48-7/8 7.0 7.2 6.0 2.5 3 R30/R502559 E2 20-5/8 54-7/8 7.9 8.1 6.7 2.5 3 R25/R502565 E2 20-5/8 60-7/8 8.7 9.0 7.5 2.5 3 R20/R502571 E2 20-5/8 66-7/8 9.6 9.9 8.3 2.5 3 R20/R502573 E2 20-5/8 68-7/8 9.9 10.2 8.5 2.5 3 R20/R502935 E3 24-5/8 30-7/8 5.3 5.4 4.5 2.5 3 R502941 E2 E2 24-5/8 36-7/8 6.3 6.5 5.4 2.5 3 R45/R502947 E E2 20 42-7/8 6.0 6.9 6.3 2.5 3 R35/R502953 E E2 20 48-7/8 6.8 7.8 7.3 2.5 3 R30/R502959 E E2 20 54-7/8 7.6 8.8 8.2 2.5 3 R25/R502965 E E2 20 60-7/8 8.5 9.7 9.1 2.5 3 R20/R502971 E E2 20 66-7/8 9.3 10.7 10.1 2.5 3 R20/R502973 E E2 20 68-7/8 9.6 11.0 10.4 3 3 R25/R503235 E2 27-5/8 30-7/8 5.9 6.1 5.0 2.5 3 R45/R503241 E2 E1 27-5/8 36-7/8 5.6 7.3 6.1 2.5 3 R35/R503247 E E 22-1/4 42-7/8 6.6 7.7 7.2 2.5 3 R30/R503253 E E 22-1/4 48-7/8 7.6 8.8 8.2 2.5 3 R25/R503259 E E 22-1/4 54-7/8 8.5 9.9 9.3 2.5 3 R25/R503265 E E 22-1/4 60-7/8 9.4 11.0 10.4 3 3 R30/R503271 E E 22-1/4 66-7/8 10.3 12.1 11.4 3 3 R25/R503273 E E 22-1/4 68-7/8 10.6 12.4 11.8 3 3 R25/R503535 E1 25-1/4 30-7/8 5.4 6.2 5.6 2.5 3 R45/R503541 E E 25-1/4 36-7/8 6.5 7.4 6.8 2.5 3 R35/R503547 E E 25-1/4 42-7/8 7.5 8.6 8.0 2.5 3 R30/R503553 E E 25-1/4 48-7/8 8.6 9.9 9.2 2.5 3 R25/R503559 E E 25-1/4 54-7/8 9.6 11.1 10.4 3 3 R25/R503565 E E 25-1/4 60-7/8 10.7 12.3 11.6 3 3 R30/R503571 E E 25-1/4 66-7/8 11.7 13.5 12.8 3 3 R25/R503573 E E 25-1/4 68-7/8 12.1 13.9 13.2 3 4 R25/R50
HE
IGH
TC
LEA
R O
PE
NIN
G
hardwarew/ side pivot
WIDTHOPENING
CLEAR
WIDTHOPENINGCLEAR
hardwarew/ standard
WIDTHOPENING
CLEAR
opening on 29" units.Sash position for clear
window open 90°.shows vent area withShaded portion
Egress Notes:
Check all applicable local codes for emer-gency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
Clear opening (egress) information does not take into consideration the addition of a Rolscreen (or any other accessory) to the product. You should consult your local building code to ensure products with Rolscreens meet egress requirements.
(—) = Not Applicable
(T) = Tempered glass due to aspect ration.
(1) Maximum performance when glazed with the appropriate glass thickness. Second value, where noted, requires tempered glass.
To convert area to square meters (m²), multiply square feet by 0.0929.
CM-48
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DESIGN DATA
Aluminum-Clad Wood
FIXED UNITS
UnitVisible Glass
Ft2
Standard Glass Thickness (mm)
Performance Class & Grade 1Annealed Tempered
4135 6.8 2.5 3.0 CW35/CW50
4141 8.3 2.5 3.0 CW30/CW50
4147 9.7 2.5 3.0 R25/CW50
4153 11.1 3.0 3.0 CW35/CW50
4159 12.6 3.0 3.0 CW30/CW50
4165 14.0 3.0 3.0 CW30/CW50
4171 15.5 3.0 3.0 R25/CW50
4173 15.9 3.0 3.0 R25/CW50
4735 8.0 2.5 3.0 CW30/CW50
4741 9.7 2.5 3.0 R25/CW50
4747 11.4 3.0 3.0 CW35/CW50
4753 13.1 3.0 3.0 CW30/CW50
4759 14.8 3.0 3.0 R25/CW50
4765 16.5 3.0 3.0 R25/CW50
4771 18.1 4.0 4.0 CW30/CW50
4773 18.7 4.0 4.0 CW30/CW50
5335 9.2 2.5 3.0 R25/CW50
5341 11.1 3.0 3.0 CW35/CW50
5347 13.1 3.0 3.0 CW30/CW50
5353 15.0 3.0 4.0 R25/CW50
5359 17.0 3.0 4.0 R25/CW50
5365 18.9 4.0 4.0 CW30/CW50
5371 20.8 4.0 4.0 CW30/CW50
5373 21.5 4.0 4.0 CW30/CW50
5935 10.4 3.0 3.0 R25/CW50
5941 12.6 3.0 3.0 CW30/CW50
5947 14.8 3.0 3.0 R25/CW50
5953 17.0 3.0 4.0 R25/CW50
5959 19.1 4.0 4.0 CW30/CW50
5965 21.3 4.0 4.0 CW30/CW50
5971 23.5 4.0 4.0 R25/CW50
5973 24.2 4.0 4.0 R25/CW50
TRANSOM UNITS
UnitClear Opening
(Inches)Vent Area Ft2
Visible Glass
Ft2
Standard Glass Thickness (mm)
Performance Class & Grade 1Width Height Ft2 Annealed Tempered
1717 7-1/4 12-7/8 0.6 1.0 0.8 2.5 3 R50
1725F — — — — 1.3 2.5 3 R50
2117F — — — — 1.1 2.5 3 R50
2121 11-1/4 16-7/8 1.3 1.8 1.5 2.5 3 R50
2125F — — — — 1.9 2.5 3 R50
2317F — — — — 1.2 2.5 3 R50
2323 13-1/4 18-7/8 1.7 2.2 1.9 2.5 3 R50
2325F — — — — 2.1 2.5 3 R50
2517F — — — — 1.3 2.5 3 R50
2525 15-1/4 20-7/8 2.2 2.8 2.4 2.5 3 R50
2917F — — — — 1.6 2.5 3 R50
2925F — — — — 2.9 2.5 3 R50
2929 19-1/4 24-7/8 3.3 4.0 3.5 2.5 3 R50
3217F — — — — 1.9 2.5 3 R50
3225F — — — — 3.3 2.5 3 R50
3517F — — — — 2.1 2.5 3 R50
3525F — — — — 3.7 2.5 3 R50
(—) = Not Applicable
F = Fixed Only
(1) Maximum performance when glazed with the appropriate glass thickness. Second value, where noted, requires tempered glass.
CM-49
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
MISCELLANEOUS FORMULAS
Aluminum-Clad Wood
* Actual glass of exterior light. Interior Hinged Glass Panel is 9/16" smaller.
Keep frame di men sions to the near est 1/4" increment.
Frame width cannot exceed frame height on special size vent units.
** Clear opening (egress) information does not take into consideration the addition of a Rolscreen (or any other accessory) to the product. You should consult your local building code to ensure products with Rolscreens meet egress requirements.
UNIT TYPE SHADE OPERATOR LOCATION FROM EXTERIOR
INTERIOR HINGED GLASS STYLE
FRAME HEIGHT > 29"
Right-Hand Vent Right Side Hinge
Left-Hand Vent Left Side Hinge
Fixed Left Side Hinge
Large Fixed Left Side Hinge
FRAME HEIGHT ≤ 29"
Right-Hand Vent Right Bottom Hinge
Left-Hand Vent Left Bottom Hinge
Fixed Left Bottom Hinge
Shade Handing Guide
Miscellaneous Formulas
VISIBLE GLASS
Width = Frame – 6-1/2"
Height = Frame – 6-1/2"
ACTUAL GLASS *
Width = Frame – 5-1/2"
Height = Frame – 5-1/2"
CLEAR OPENING HEIGHT **
Frame Height - 4-1/8"
CLEAR OPENING WIDTH **
Hinge Frame Width Formula
Standard FW ≥ 29" and ≤ 30-1/2" FW - 9"
Standard FW > 30-1/2" FW - 9-3/4"
Side Pivot FW ≥ 25" and < 35" FW - 4-3/8"
Rev. 05/13/2015
CM-50
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DETAILED PRODUCT DESCRIPTIONS
Aluminum-Clad Wood
(1) Contact your local Pella sales representative for current designs and color options.
FRAME
• Select softwood, immersion treated with Pella’s EnduraGuard® wood protection formula in accordance with WDMA I.S.-4. The EnduraGuard formula includes three active ingredients for protection against the effects of moisture, decay, stains from mold and mildew. Plus, an additional ingredient adds protection against termite damage.
• Interior exposed surfaces are clear pine.• Exterior surfaces are clad with aluminum. • Overall frame depth is 5" (127mm) for a wall depth of 3-11/16" (94mm).• Optional factory-applied jamb extensions available between 4-9/16"
(116mm) and 6-9/16" (167mm) wall depths.• Optional factory-installed fold-out installation fins with flexible fin corners.• Optional factory-applied EnduraClad® exterior trim.
SASH
• Select softwood, immersion treated with Pella’s EnduraGuard® wood protection formula in accordance with WDMA I.S.-4. The EnduraGuard formula includes three active ingredients for protection against the effects of moisture, decay, stains from mold and mildew. Plus, an additional ingredient adds protection against termite damage.
• Interior exposed surfaces are clear pine.• Exterior surfaces are clad with aluminum, lap-jointed and sealed. • Corners mortised and tenoned, glued and secured with metal fasteners. • Sash thickness is 2-3/16" (55mm).
WEATHERSTRIPPING
• Dual weatherstripping. � Flexible santoprene material compressed between frame and sash
for positive seal on all four sides. � Secondary thermoplastic vulcanizate (TPV) leaf-type weatherstrip
between edge of sash and frame.
GLAZING SYSTEM
• Quality float glass complying with ASTM C 1036.• Triple-Pane Glazing
� Exterior dual-seal insulating glass, silicone-glazed, [[annealed / heat strengthened] [tempered]] [[clear] [[Advanced] [SunDefense™][AdvancedComfort] [NaturalSun] Low-E coated, with argon] [[bronze] [gray] [green] [non-impact laminated] Advanced Low-E coated, with argon]].
� High altitude glazing available. � Interior hinged glass panel set in veneer covered aluminum frame,
fitted to sash with continuous gasket seal, [[annealed] [tempered]] [[clear] [obscure]].
� Airspace is 1-3/32".
EXTERIOR
• Aluminum clad exteriors shall be finished with EnduraClad® protective finish, in a multi-step, baked-on finish.
• Color is [White] [Tan] [Brown] [Putty] [feature1] [custom1]. – or –
• Aluminum clad exteriors shall be finished with EnduraClad Plus protective finish with 70% fluoropolymer resin in a multi-step, baked-on finish.
• Color shall be [White] [Tan] [Brown] [Putty] [feature1] [custom1].
INTERIOR
• [Unfinished, ready for site finishing] [factory primed with one coat acrylic latex] [factory prefinished [White] [Linen White] [Bright White] [stain1]].
HARDWARE
• Roto operator assembly � Steel worm gear sash operator with hardened gears. � Operator base is zinc die cast with painted finish. � Operator linkage, hinge slide, and hinge arms are stainless steel. � Exposed fasteners are stainless steel. � Hardware shall exceed 1,000 hours salt spray exposure per
ASTM B 117. • Finish of integrated fold-away crank is [[baked enamel [Champagne]
[White] [Brown]] [Bright Brass] [Satin Nickel] [Oil-Rubbed Bronze]. • SureLock® System—A single handle locking system operates positive-
acting arms that reach out and pull the sash into a locked position: one unison operating lock installed on units with frame height 29" and smaller, installed on units with frame height greater than 29".
• Lock handle finish is [[baked enamel [Champagne] [White] [Brown]] [Bright Brass] [Satin Nickel] [Oil-Rubbed Bronze].
OPTIONAL PRODUCTS
Grilles• Removable Between-Glass Grilles
� 3/4" profile with [Traditional] [Prairie] [Cross] [Top Row] [New England] patterns that are a contoured aluminum grille installed on the edge of the hinged glass panel.
� Interior [unfinished, ready for site finishing] [factory primed] [pine: factory prefinished [White] [Linen White] [Bright White] [stain1]].
� Exterior finish will match exterior color cladding.Screens• InView™ Screens
� Vinyl-coated 18/18 mesh fiberglass screen cloth complying with SMA 1201, set in aluminum frame fitted to inside of window, supplied complete with all necessary hardware.
� Screen frame finish is baked enamel, [Champagne] [White] [Brown].– or –
• Vivid View® Screens � PVDF 21/17 mesh, minimum 78 percent light transmissive screen, set
in aluminum frame fitted to inside of window, supplied complete with all necessary hardware.
� Screen frame finish is baked enamel, [Champagne] [White] [Brown]. – or –
• Rolscreen® Retractable Screens � Self-storing, rolling, black vinyl-coated 18/16 mesh fiberglass screen
cloth complying with ASTM D 3656 and SMA 1201 mounted behind overhead cover.
� Cover finish is [factory prefinished paint] [pine veneer wrapped over extruded aluminum with factory prefinished [stain1][paint1]].
� Guides are aluminum extrusion with [pine veneer wrapped over extruded aluminum with factory prefinished [stain1][paint1]].
Window Fashions• Slimshade® Blinds1
� 15mm aluminum slat [tilt-only] [bottom-up] blinds with polyester cord ladder.
� Installed on the hinged glass panel and controlled by a built-in cordless operating mechanism.
– or –• Cellular Fabric Shades1
� Spun bond Polyethylene Terephthalate (PET) cellular fabric, 11/16" in width, hidden polyester cord [bottom-up] [top-down].
� Installed on the hinged glass panel and controlled by a built-in cordless operating mechanism.
Hardware• Optional factory applied limited opening hardware available for vent units
in stainless steel; nominal 3" opening.• Optional window opening control device available for field installation.
Device allows window to open less than 4" with normal operation, with a release mechanism that allows the sash to open completely. Complies with ASTM F2090-10.
Rev. 07/13/2015
CM-51
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
UNIT SECTIONSAluminum-Clad WoodTriple-Pane Glazing
[57]
2 1/
4"[5
7]2
1/4"
[57]2 1/4"
[57]2 1/4"
FRA
ME
HE
IGH
T
FRAME WIDTH
VENT / FIXEDVERTICAL JOINING MULLION
TRANSOM / VENTHORIZONTAL JOINING MULLION
VENT / VENTVERTICAL JOINING MULLION
FIXED
VENT
[19]
3/4"
[19]
3/4"
FRA
ME
HE
IGH
T
[57]
2 1/
4"
[94]
3 11
/16"
[19]3/4"
[19]3/4"
[63]2 1/2"
FRAME WIDTHInstallation Fin
Optional Fold-out
[33]
1 5/
16"
[82]3 1/4"
[82]
3 1/
4"
[127]5"
[82]
3 1/
4"[5
7]2
1/4"
[19]
3/4"
[82]3 1/4"
[33]
1 5/
16"
Installation FinOptional Fold-out [57]
2 1/4"[19]3/4"
[19]
3/4"
[94]
3 11
/16"
[19]3/4"
FS
FH
FJ
VS
VH
LJ HJ
FS FIXED SILL
FH FIXED HEAD
VS VENT SILL
LOCK JAMBLJ HINGE JAMBHJ
VH VENT HEAD
FJ FIXED JAMB
Scale 3" = 1' 0"
All dimensions are approximate.
See Installation and Performance at www.PellaADM.com for mullion limitations and reinforcing requirements.
TYPICAL JOINING MULLIONS
CM-52
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
UNIT SECTIONSAluminum-Clad WoodRolscreen Retractable Screen
See Installation and Performance at www.PellaADM.com for mullion limitations and reinforcing requirements.
All dimensions are approximate.
Scale 3" = 1' 0"
[57]
2 1/
4"
[57]2 1/4"
FRA
ME
HE
IGH
T
FRAME WIDTH
INSECT SCREENROLSCREENVENT WITHVENTVENT
[127]5"
[82]
3 1/
4"[5
7]2
1/4"
[19]
3/4"
[19]
3/4"
[33]
1 5/
16"
Installation FinOptional Fold-out [57]
2 1/4"[19]3/4"
[19]3/4"
[94]
3 11
/16"
[82]3 1/4"
VS
VH
LJ HJ
VS
VH
LJ HJ
VS VENT SILL
VH VENT HEAD
HINGE JAMBHJLOCK JAMBLJ
CM-53
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
GRILLE TYPES
VG = Visible Glass
(1) Grilles are available in traditional patterns only.
Lite dimensions noted can vary.
For size and pattern availability; contact your local Pella sales representative.
For traditional patterns, see size tables.
Grille Patterns
Grilles-Between-the Glass and Simulated-Divided-Light Grilles
VG
VG
VG
VG
TraditionalEqually Divided
Custom 2x2Top Row CrossPrairie9-Lite
Prairie
– Standard corner lite dimension for Prairie patterns = 2-1/2" VG.
Cross
– Available for units with frame heights ≥35".
– Standard visible glass to separator bar = 1/4 of total visible glass height.
Top Row
– Standard visible glass to separator bar = 12" for a frame height equal to 35".
– Standard visible glass to separator bar = 12" or 14" for a frame height equal to 41".
– Standard visible glass to separator bar = 12", 14" or 16" for frame heights greater than 41".
9-Lite Prairie Top Row Cross Custom 2x2 Equally Divided
Simulated-Divided-Light Grilles Simulated-Divided-Light Grilles with optional spacer
Removable Interior Pine Grilles Grilles-Between-the-Glass
Contoured Grille3/4"
1"3/4"
Contoured Grille1"
Contoured Grille3/4"
3/4"
3/4" Regular
2"1 1/4"2"
2" Regular
1 1/4"
1 1/4" Regular
3/4"
1
2" Colonial1 1/4" Colonial3/4" Regular
Grille Profiles
Rev. 06/05/2015
CM-54
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
SIZE TABLES
Aluminum-Clad Wood
Not to scale.
Fixed units only. T Tempered glass is standard. Traditional grille patterns shown. Refer to Clad / Wood Overview Section for additional patterns and profiles.
3214
3271
3265
3259
3253
3247
3241
3235
3225
3217
Vent and Fixed Units
2114 2314 2514 2914 35141714
1717
1725
1735
1741
1747
1753
1759
1765
2117
2125
2135
2141
2147
2153
2159
2165
2371
2365
2359
2353
2347
2341
2335
2325
2317
2571
2565
2559
2553
2547
2541
2535
2525
2517
2971
2965
2959
2953
2947
2941
2935
2925
2917
3571
3565
3559
3553
3547
3541
3535
3525
3517
2121
2323
2929
21711771
Transoms
4"3 /
(813)(832)
2' 8"2' 8
4"3
/4"
3/
(356
)
1' 2(3
75) 4"
3/
1' 2
"4"
3/
4"3
/4"
3/
4"3
/4"
3/
4"3
/4"
3/
4"3
/4"
3/
4"3
/
Frame
Opening
(1 8
03)
(1 8
22)
5' 1
1"5'
11
(1 6
51)
(1 6
70)
5' 5
"5'
54'
11
4' 1
1"
(1 5
18)
(1 4
99)
4' 5
4' 5
"
(1 3
65)
(1 3
46)
(1 0
41)
(1 0
60)
3' 5
"3'
52'
12'
1"
(654
)(6
35)
2' 1
1"2'
11
(908
)(8
89)
2' 5
2' 5
"
(756
)(7
37)
1' 1
11'
11"
(603
)(5
84)
(533
)(5
52)
1' 9
"1'
91'
51'
5"
(451
)(4
32)
(1 1
94)
(1 2
13)
3' 1
1"3'
11
4"3 /4"3 /4"3 /4"3 /4"3 /4"3 / 2' 12' 1"
(654)(635)
1' 111' 11"
(603)(584)
1' 91' 9"
(552)(533)
1' 51' 5"
(451)(432) (737)
(756)
2' 5"2' 5
2' 11"2' 11
(908)(889)
2E3E
2E1E
F
F
F
E
E
E
E
E
F
F
F F
F F
F F F
F F
FFFFF
2E EE
2E
2E
2E
2E
3E 2E1E
E
E
E
E
1E
E
E
E
E
E
T
Fixed Units
5971
5965
5953
5947
5941
5371
5365
5353
5347
5341
4771
4765
4753
4747
4741
4171
4165
4153
4147
4141
4159 4759 5359 5959
FrameOpening
3' 1
13'
11"
(1 2
13)
(1 1
94)
3' 5
3' 5
"
(1 0
60)
(1 0
41)
(1 3
46)
(1 3
65)
4' 5
"4'
55'
55'
5"
(1 6
70)
(1 6
51)
5' 1
15'
11"
(1 8
22)
(1 8
03)
4"3
/4"
3/
4"3
/
3' 53' 5"
(1 060)(1 041) (1 194)
(1 213)
3' 113' 11" 4' 11"
4' 11
(1 518)(1 499)(1 346)
(1 365)
4' 5"4' 54"3 / 4"3 / 4"3 / 4"3 /
4"3
/4"
3/
4' 1
14'
11"
(1 5
18)
(1 4
99)
4"3
/
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
See Design Data pages in this section for clear opening dimensions.
CM-55
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DESIGN DATA
Aluminum-Clad Wood
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
(—) = Not Applicable
TR = Second number shown requires tempered glass.
TR3 = Second number shown requires tempered glass and DP Kit.
T = Tempered required due to aspect ratio.
(1) Maximum performance when glazed with the appropriate glass thickness.
(2) Glass thickness shown for Advanced Low-E. Other Low-E types and clear use 3mm glass
Refer to the Product Performance section at PellaADM.com for more information.
VENT AND FIXED UNITS
Unit
Eg
ress
Clear Opening(Inches)Vent Area Ft2
Visible Glass
Ft2
Standard Glass Thickness (mm) Performance Class & Grade 1
Width Height Ft2Vent Fixed
Annealed Tempered Annealed Tempered Vent Fixed1735 7-1/4 30-7/8 1.6 2.5 2.5 2.5 3 3 3 R50 R501741 7-1/4 36-7/8 1.9 2.9 3.0 2.5 3 3 3 R50 R501747 7-1/4 42-7/8 2.2 3.4 3.5 2.5 3 3 3 R50 R501753 7-1/4 48-7/8 2.5 3.9 4.0 2.5 3 3 3 R50 R501759 7-1/4 54-7/8 2.8 4.4 4.5 2.5 3 3 3 R50 R501765 7-1/4 60-7/8 3.1 4.9 5.0 2.5 3 3 3 R50 R501771T 7-1/4 66-7/8 3.4 5.3 5.5 — 3 — 3 R50 R502135 11-1/4 30-7/8 2.4 3.3 3.4 2.5 3 2.5(2) 3 R50 R502141 11-1/4 36-7/8 2.9 4.0 4.0 2.5 3 2.5(2) 3 R50 R502147 11-1/4 42-7/8 3.3 4.6 4.7 2.5 3 2.5(2) 3 R50 R502153 11-1/4 48-7/8 3.8 5.3 5.4 2.5 3 2.5(2) 3 R50 R502159 11-1/4 54-7/8 4.3 5.9 6.0 2.5 3 2.5(2) 3 R45/R50TR R502165 11-1/4 60-7/8 4.8 6.6 6.7 2.5 3 3 3 R45/R50TR R502171 11-1/4 66-7/8 5.2 7.2 7.4 2.5 3 3 3 R40/R50TR R502335 13-1/4 30-7/8 2.8 3.8 3.8 2.5 3 2.5(2) 3 R50 R502341 13-1/4 36-7/8 3.4 4.5 4.5 2.5 3 2.5(2) 3 R50 R502347 13-1/4 42-7/8 3.9 5.2 5.3 2.5 3 2.5(2) 3 R50 R502353 13-1/4 48-7/8 4.5 5.9 6.0 2.5 3 2.5(2) 3 R50 R502359 13-1/4 54-7/8 5.0 6.7 6.8 2.5 3 2.5(2) 3 R45/R50TR R502365 13-1/4 60-7/8 5.6 7.4 7.5 2.5 3 3 3 R40/R50TR R502371 13-1/4 66-7/8 6.2 8.1 8.3 2.5 3 3 3 R30/R50TR3 R502535 15-1/4 30-7/8 3.3 4.2 4.2 2.5 3 2.5(2) 3 R50 R502541 E3 20-5/8 36-7/8 3.9 5.0 5.0 2.5 3 2.5(2) 3 R50 R502547 E2 20-5/8 42-7/8 4.5 5.8 5.9 2.5 3 2.5(2) 3 R50 R502553 E2 20-5/8 48-7/8 5.2 6.6 6.7 2.5 3 2.5(2) 3 R50 R50 2559 E2 20-5/8 54-7/8 5.8 7.4 7.5 2.5 3 2.5(2) 3 R45/R50TR R502565 E2 20-5/8 60-7/8 6.4 8.2 8.4 2.5 3 2.5(2) 3 R40/R50TR R502571 E2 20-5/8 66-7/8 7.1 9.1 9.2 3 3 3 3 R30/R50TR3 R502935 E3 24-5/8 30-7/8 5.3 5.0 5.0 2.5 3 2.5(2) 3 R50 R502941 E2 24-5/8 36-7/8 6.3 6.0 6.0 2.5 3 2.5(2) 3 R50 R502941 E1 20 36-7/8 5.1 6.0 6.0 2.5 3 2.5(2) 3 R50 R502947 E 20 42-7/8 6.0 7.0 7.0 2.5 3 2.5(2) 3 R50 R502953 E 20 48-7/8 6.8 8.0 8.0 2.5 3 2.5(2) 3 R50 R502959 E 20 54-7/8 7.6 9.0 9.0 2.5 3 2.5(2) 3 R45/R50TR R502965 E 20 60-7/8 8.5 9.9 10.0 2.5 3 2.5(2) 3 R30/R50TR3 R502971 E 20 66-7/8 9.3 10.9 11.1 3 3 3 3 R30/R50TR3 R45/R50TR
3235 E2 27-5/8 30-7/8 5.9 6.1 5.7 2.5 3 2.5(2) 3 R50 R503241 E2 27-5/8 36-7/8 7.1 7.3 6.8 2.5 3 2.5(2) 3 R50 R503247 E 22-1/4 42-7/8 6.6 7.9 7.9 2.5 3 2.5(2) 3 R50 R503253 E 22-1/4 48-7/8 7.5 9.0 9.0 2.5 3 2.5(2) 3 R50 R503259 E 22-1/4 54-7/8 8.4 10.1 10.2 2.5 3 2.5(2) 3 R45/R50TR R503265 E 22-1/4 60-7/8 9.4 11.2 11.3 3 3 3 3 R30/R50TR3 R503271 E 22-1/4 66-7/8 10.3 12.3 12.4 3 3 3 3 R30/R50TR3 R45/R50TR
3535 E1 25-1/4 30-7/8 5.4 6.3 6.3 2.5 3 2.5(2) 3 R50 R503541 E 25-1/4 36-7/8 6.5 7.6 7.5 2.5 3 2.5(2) 3 R50 R503547 E 25-1/4 42-7/8 7.5 8.8 8.8 2.5 3 2.5(2) 3 R50 R503553 E 25-1/4 48-7/8 8.6 10.0 10.0 2.5 3 2.5(2) 3 R45/R50TR R503559 E 25-1/4 54-7/8 9.6 11.2 11.3 3 3 3 3 R30/R50TR3 R50 3565 E 25-1/4 60-7/8 10.7 12.5 12.6 3 3 3 3 R30/R50TR3 R503571 E 25-1/4 66-7/8 11.7 13.7 13.8 3 3 3 3 R30/R50TR3 R45/R50TR
open 90°.with windowshows vent areaShaded portionH
EIG
HT
CLE
AR
OP
EN
ING
hardwarew/ side pivot
WIDTHOPENING
CLEARWIDTH
OPENINGCLEAR
hardwarew/ standard
WIDTHOPENING
CLEAR
VENT AREA
29" units.clear opening onSash position for
CM-56
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DESIGN DATA
Aluminum-Clad Wood
CLEAR OPENING HEIGHT
Frame Height - 4-1/8"
CLEAR OPENING WIDTH
Hinge Frame Width Formula
Standard FW ≥ 29" and ≤ 30-1/2" FW - 9"
Standard FW > 30-1/2" FW - 9-3/4"
Side Pivot FW ≥ 25" and < 35" FW - 4-3/8"
VISIBLE GLASSWidth = Frame – 4-15/16"
Height = Frame – 4-15/16"
ACTUAL GLASSWidth = Frame – 4"
Height = Frame – 4"
Miscellaneous Formulas
Special Size Frame Dimensions*
MINIMUM MAXIMUM
VENT1'5" W x 1'5" H
(432 x 432)
2'11" W x 5' 11" H(889 x 1 803)
FIXED1'5" W x 1'5" H
(432 x 432)
4'11" W x 5'11" H(1499 x 1 803)
* Available within size range shown. Keep frame di men sions to the near est 1/4" increment. Frame width cannot exceed frame height on special size vent units.
(—) = Not Applicable
F = Fixed units only.
TR = Second number shown requires tempered glass.
(1) Maximum performance when glazed with the appropriate glass thickness.
(2) Glass thickness shown for Advanced Low-E. Other Low-E types and clear use 3mm glass
Refer to the Product Performance section at PellaADM.com for more information.
FIXED UNITS
UnitVisible Glass
Ft2
Standard Glass Thickness (mm) Performance
Class & Grade 1Annealed Tempered
4141 9.0 3 3 R504147 10.5 3 3 R504153 12.0 3 3 R504159 13.6 3 3 R504165 15.1 3 3 R504171 16.6 3 3 R45/R50TR
4741 10.5 3 3 R504747 12.3 3 3 R50
4753 14.1 3 3 R504759 15.8 3 3 R45/R50TR
4765 17.6 3 3 R45/R50TR
4771 19.3 4 4 R505341 12.0 3 3 R505347 14.1 3 3 R505353 16.1 4 4 R45/R50TR
5359 18.1 4 4 R505365 20.1 4 4 R505371 22.1 4 4 R505941 13.6 3 3 R505947 15.8 3 3 R45/R50TR
5953 18.1 4 4 R505959 20.3 4 4 R505965 22.6 4 4 R505971 24.8 4 4 R45/R50TR
TRANSOM UNITS
Unit
Clear Opening (Inches)
Vent Area Ft2
Visible Glass
Ft2
Standard Glass Thickness (mm)
Performance Class & Grade 1Width Height Ft2 Annealed Tempered
1714F — — — — 0.8 3 3 R50
1717 7-1/4 12-7/8 0.6 1.1 1.0 3 3 R50
1725F — — — — 1.7 3 3 R50
2114F — — — — 1.0 3 3 R50
2117F — — — — 1.3 3 3 R50
2121 11-1/4 16-7/8 1.3 2.0 1.8 3 3 R50
2125F — — — — 2.2 3 3 R50
2314F — — — — 1.1 3 3 R50
2317F — — — — 1.5 3 3 R50
2323 13-1/4 18-7/8 1.7 2.4 2.3 3 3 R50
2325F — — — — 2.5 3 3 R50
2514F — — — — 1.3 3 3 R50
2517F — — — — 1.7 3 3 R50
2525 15-1/4 20-7/8 2.2 3.0 2.8 3 3 R50
2914F — — — — 1.5 3 3 R50
2917F — — — — 2.0 3 3 R50
2925F — — — — 3.4 3 3 R50
2929 20-1/4 24-7/8 3.3 4.3 4.0 3 3 R50
3214F — — — — 1.7 3 3 R50
3217F — — — — 2.3 3 3 R50
3225F — — — — 3.8 3 3 R50
3514F — — — — 1.9 3 3 R50
3517F — — — — 2.5 3 3 R50
3525F — — — — 4.2 2.5(2) 3 R50
CM-57
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
DETAILED PRODUCT DESCRIPTIONS
Aluminum-Clad Wood
(1) Available on units glazed with Low-E insulated glass with argon and obscure insulated glass.
(2) Tan, brown and putty Interior GBG colors are available in single-tone (Brown/Brown, Tan/Tan or Putty/Putty) (Putty mono available spring 2015). Other interior colors are also available with tan or brown exterior.
(3) Contact your local Pella sales representative for current color options.
(4) Appearance of exterior grille color will vary depending on Low-E coating on glass.
FRAME
• Select softwood, immersion treated with Pella’s EnduraGuard® wood protection formula in accordance with WDMA I.S.-4. The EnduraGuard formula includes three active ingredients for protection against the effects of moisture, decay, stains from mold and mildew. Plus, an additional ingredient adds protection against termite damage
• Interior exposed surfaces are clear pine.• Exterior surfaces are clad with aluminum. • Overall frame depth is 5" (127mm) for a wall depth of 3-11/16"
(94mm).• Optional factory-applied jamb extensions available.• Optional factory-installed fold-out installation fins with flexible fin corners.• Optional factory-applied EnduraClad® exterior trim.
SASH
• Select softwood, immersion treated with Pella’s EnduraGuard® wood protection formula in accordance with WDMA I.S.-4. The EnduraGuard formula includes three active ingredients for protection against the effects of moisture, decay, stains from mold and mildew. Plus, an additional ingredient adds protection against termite damage.
• Interior exposed surfaces are clear pine.• Exterior surfaces are clad with aluminum, lap-jointed and sealed. • Corners mortised and tenoned, glued and secured with metal fasteners. • Sash thickness is 1-3/4" (45mm).
WEATHERSTRIPPING
• Vent units use Dual weatherstripping. � Flexible santoprene material compressed between frame and sash for
positive seal on all four sides. � Secondary thermoplastic vulcanizate (TPV) leaf-type weatherstrip
between edge of sash and frame on the vertical sides and bottom, and Santoprene® bulb-type weatherstrip between the edge of sash and frame on the top.
• Fixed units use a Flexible EPDM material compressed between frame and sash for positive seal on all four sides.
GLAZING SYSTEM
• Quality float glass complying with ASTM C 1036. � Silicone-glazed 11/16" [obscure 1] dual-seal insulating glass [[annealed]
[tempered]] [Advanced] [SunDefense™] [AdvancedComfort][NaturalSun] Low-E coated, with argon] .
� High altitude glazing available.
EXTERIOR
• Aluminum clad exteriors shall be finished with EnduraClad® protective finish, in a multi-step, baked-on finish.
• Color is [Standard: [White] [Tan] [Brown] [Putty]] [Feature: [Poplar White] [Hartford Green] [Black] [Brick Red] [Morning Sky Gray (Spring 2015)] [Portobello (Spring 2015)]].
INTERIOR
• [Unfinished, ready for site finishing] [factory primed with one coat acrylic latex] [factory prefinished [White] [Linen White] [Bright White] [stain 3]].
HARDWARE
• Roto operator assembly � Steel worm gear sash operator with hardened gears. � Operator base is zinc die cast with painted finish. � Operator linkage, hinge slide, and hinge arms are stainless steel. � Exposed fasteners are stainless steel. � Hardware will exceed 1,000 hours salt spray exposure per
ASTM B 117. • Finish of operator crank is [[baked enamel [Champagne, for unfinished
prime units] [White, for prefinished White units] [Brown]]. Operator crank also available in optional [Bright Brass] [Satin Nickel] [Oil-Rubbed Bronze]. All vent units are available with left- or right-hand hinging.
• SureLock® System—A single handle locking system operates positive-acting arms that reach out and pull the sash into a locked position: one unison operating lock installed on units with frame height 29" and smaller, two installed on units with frame height greater than 29".
• Lock handle finish is [[baked enamel [Champagne, for unfinished prime units] [White, for prefinished White units] [Brown]]. Lock handle also available in optional [Bright Brass] [Satin Nickel] [Oil-Rubbed Bronze].
OPTIONAL PRODUCTS
Grilles• Removable Grilles
� 3/4" Traditional removable solid wood grilles steel-pinned at joints and fitted to sash with steel clips and tacks.
� Interior [unfinished, ready for site finishing] [factory primed] [pine: factory prefinished [White] [Linen White] [Bright White] [stain 1]].
� Exterior [unfinished, ready for site finishing] [Factory Primed] [factory prefinished, finish color matched to exterior cladding].
– or –• Grilles-Between-the-Glass 1
� Insulating glass contains 3/4" contoured aluminum grilles permanently installed between two panes of glass.
� Patterns are [Traditional] [9-Lite Prairie] [Cross] [Top Row] [Custom – Equally Divided].
� Interior color is [White] [Tan2] [Brown2] [Putty2] [Ivory] [Brickstone] [Harvest] [Cordovan].
� Exterior grilles match the exterior cladding color4.– or –
• Simulated Divided Light [with spacer] � Grilles permanently bonded to the interior and exterior of glass. � Interior grilles are [unfinished, ready for site finishing] [factory primed]
[pine: factory prefinished [White] [Linen White] [Bright White] [stain 3]]. � Patterns are [Traditional] [9-Lite Prairie] [Cross] [Top Row] [Custom –
Equally Divided]. � Exterior grilles match the exterior cladding color.
Screens• InView™ screens
� Vinyl-coated 18/18 mesh fiberglass screen cloth complying with SMA 1201, set in aluminum frame fitted to inside of window, supplied complete with all necessary hardware.
� Screen frame finish is baked enamel, [Champagne] [White] [Brown].– or –
• Vivid View® screens � PVDF 21/17 mesh, minimum 78 percent light transmissive screen, set in
aluminum frame fitted to inside of window, supplied complete with all necessary hardware.
� Screen frame finish is baked enamel [Champagne] [White] [Brown].Hardware• Optional factory applied limited opening hardware available for vent units
in stainless steel; nominal 3" opening.• Optional window opening control device available for field installation.
Device allows window to open less than 4" with normal operation, with a release mechanism that allows the sash to open completely. Complies with ASTM F2090-10.
Rev. 07/13/2015
CM-58
CASEMENT
Pella 2015 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
Architect Series® Designer Series® Pella® ProLine 450
UNIT SECTIONS
Aluminum-Clad Wood
Scale 3" = 1' 0" All dimensions are approximate. See Installation and Performance at www.PellaADM.com for mullion limitations and reinforcing requirements.
[45]1 3/4"
[45]
1 3/
4"[4
5]1
3/4"
FRAME WIDTH
FRA
ME
HE
IGH
T
[45]1 3/4"
Installation FinOptional Fold-out
Installation FinOptional Fold-out
FRAME WIDTH
[37]1 7/16"
[19]3/4"
[62]2 7/16"
[62]2 7/16"
[19]3/4"
[37]1 7/16"
[62]
2 7/
16"
[19]
3/4"
[37]
1 7/
16"
FRA
ME
HE
IGH
T
[19]3/4"
[19]
3/4"
[94]
3 11
/16"
[33]
1 5/
16"
VENT
FIXED[19]3/4"
[19]
3/4"
[37]
1 7/
16"
[19]
3/4"
[33]
1 5/
16"
[94]
3 11
/16"
[62]
2 7/
16"
[127]5"
VENT / FIXEDVERTICAL JOINING MULLION
FIXED / VENTHORIZONTAL JOINING MULLION
VENT / VENTVERTICAL JOINING MULLION
FJ
FS
VS
VH
FH
HJLJ
FJ FIXED JAMB
LOCK JAMBLJ HINGE JAMBHJ
FS FIXED SILL
VS VENT SILL
VH VENT HEAD
FH FIXED HEAD
TYPICAL JOINING MULLIONS