Sec 71 (3710,3715), Jan. 2019 Sec 71 (3710,3715) · 2020. 2. 21. · 17 70996 1 Gearbox, 540 RPM...

PARTS MANUALSECTION

Important Operatingand Safety Instructionsare found in the MowerSafety Video that canbe instantly accessedon the internet at:www.algqr.com/bve

An Operator’s Manual was shipped with the equipment. The Operator’s Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator’s Manual is not with the equipment, contact your dealer or Bush Hog to obtain a copy before operating the equipment.

2

Revised, 01/19

71

3715/371013715/13710

FLEX WING ROTARY MOWER

© 2012 Alamo Group Inc.

BUSH HOG/ LAND MAINTENANCE REPAIR PARTS MANUAL

3710, 3715, 13710, 13715, 3715 BRUSH CUTTERFLEX-WING CUTTERS – 540 RPM

13715, 13710 FLEX-WING CUTTERS – 1000 RPM

ALPHABETICAL INDEX

CONTENTS PAGEAxle Arms .................................................................................................................................................71-5-8, 71-5-9Axle Assembly ..............................................................................................................................71-5-5 through 71-5-7Baffle Kit ................................................................................................................................................................71-6-3Bands, Rear ..........................................................................................................................................................71-2-4Belting, Front.........................................................................................................................................................71-2-3Chains, Front.........................................................................................................................................................71-2-1 Rear ............................................................................................................................................................71-2-2 Safety Tow .....................................................................................................................................71-5-1, 71-5-2Decals ...................................................................................................................................................................71-8-1Deck Assembly, Center.........................................................................................................................................71-1-1 Right Hand Wing.........................................................................................................................................71-1-2 Left Hand Wing, 3715, 3715 Brush Cutter & 13715....................................................................................71-1-3 Side Band, 3710 & 13710...........................................................................................................................71-1-4Driveline Holder.....................................................................................................................................................71-5-4Driveshaft Assemblies ................................................................................................................71-4-1 through 71-4-24Gearbox Assemblies ....................................................................................................................71-3-1 through 71-3-4Hitch Assemblies...................................................................................................................................................71-5-3Hub Assemblies........................................................................................................................................71-5-7, 71-5-8Hydraulic Cylinders...................................................................................................................................71-7-6, 71-7-7Hydraulics, 3715 & 13715. ....................................................................................................................................71-7-1 3710 & 13710 .............................................................................................................................................71-7-2Jackstand..................................................................................................................................................71-5-1, 71-5-2Leveling Rod.............................................................................................................................................71-5-1, 71-5-2Manual Wing Lift ...................................................................................................................................................71-6-1Pillow Block .........................................................................................................................................................71-4-10Shield Assembly, Center ..........................................................................................................................71-2-5, 71-2-7 Wing............................................................................................................................................................71-2-6Tongue......................................................................................................................................................71-5-1, 71-5-2Valve, Hydraulic Control, 3 Spool .........................................................................................................................71-7-3 Hydraulic Control, 2 Spool ..........................................................................................................................71-7-4 Stand Kit .....................................................................................................................................................71-7-5Wheels and Tires..................................................................................................................................71-5-10, 71-5-11Winch Assembly....................................................................................................................................................71-6-2

January, 2019


BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

71-1-1

REF. PARTNO. NO. QTY. DESCRIPTION

1 50028747 1 Center Deck w/ Decals 50028751 1 Center Deck (Rings) w/ Decals 2 50028363 1 Shaft Cover Weld(3710) 3 44315BH 4 Capscrew M8 x 1.25 x 20 4 44311BH 4 Lockwasher M8 5 D549 1 Sheet Decal 6 D553 1 Decal, Warning 7 50029689 2 Skid 8 44134BH 8 Carriage Bolt 1/2” x 1-3/4” 9 –––– 2 Flatwasher 1” 10 –––– 8 Flatwasher 1/2” 11 –––– 8 Lockwasher 1/2” 12 –––– 8 Hex Nut 1/2” 13 84672 2 Pin 14 1273BH 3 Presto Pin 15 50069118 2 Hinge Pin 16 50029759 2 Hinge Connector 17 –––– 6 Capscrew 3/4” x 2-1/2” G8 18 20299 6 Locknut 3/4” Flanged 19 20414 4 Locknut, Flanged 5/8” 20 –––– 4 Capscrew 5/8” x 2-1/4”


21 63607 1 Blade Bolt Kit 22 7919BH 2 Blade Bolt 23 20322 2 Lockwasher 1-1/8” 24 252BH 2 Hex Nut 1-1/8” 25 7556BH 2 Blade, CCW Rotation 97034BH 2 Blade, CCW, High Lift (Optional) 26 50057117 1 Blade Pan 27 70996 1 Gearbox, 540 RPM (3710, 3715) 71198 1 Gearbox, 1000 RPM (13710, 13715) 70998 1 Gearbox, 1000 RPM (3715 Brush Cutter) 28 71202 1 Transfer Gearbox, 540 RPM Comer *50045696 1 Transfer Gearbox, 540 RPM B&P *Replaced By 71202 Gearbox Assy. 71203 1 Transfer Gearbox, 1000 RPM Comer 50045697 1 Transfer Gearbox, 1000 RPM B&P 29 50058536 1 Center Driveshaft 30 76664 1 Spring Washer 31 70418 1 Castle Nut 32 70419 1 Cotter Pin 33 D565 2 Decal, Danger 34 50028476 2 Wing Latch 35 –––– 4 Capscrew 3/8” x 2” 36 –––– 4 Flatwasher 3/8” 37 20363 4 Locknut 3/8” 38 –––– 2 Capscrew 3/4” x 2-1/2” G5 39 20638 2 Locknut 3/4” 40 50029677 1 Transport Latch 41 50029784 1 Pin, Transport 42 21020614 1 Cotter Pin 43 50029783 1 Pin 45 D546 1 Decal, Danger 46 D587 1 Decal, Lube Chart 47 D614 2 Decal, Danger Thrown Objects 48 D555 2 Decal, Danger 49 D547 1 Decal, Danger / Warning 50 D559 1 Decal (Genuine BH Parts) 51 D551 1 Decal, Blade Rotation 52 D544 1 Decal, Important 53 91443 1 Decal , Inportant 54 D575 1 Decal, Danger (Crushing Hazard) 55 D813 1 Decal, Danger - Multilingual 56 D548 1 Decal, Warning (1000 RPM Mod. Only)

CENTER DECK ASSEMBLYModels 3710 & 3715,

3715 Brush Cutter – 540 RPM13710 & 13715 – 1000 RPM

6

2829

27

1

7

21

2525

26

5

24 3

38

17

18

39

1314

14

3415

16

35, 36, 37

30

3132

8, 10, 11, 12

8, 10, 11, 12

19, 20

2423

33

33

53

46

47

40

9

43

9

42

52

5047

4856, 49

45

51

41

22

54

55

Overlay On1000 RPMMod. Only)



71-1-2


1 50028746 1 Wing Frame w/ Decals, R.H. 50028750 1 Wing Frame (w/ Rings) w/ Decals, R.H. 2 50040103 1 Front Skid 3 50040105 1 Rear Skid 4 3161212 6 Plow Bolt 3/8” x 1-1/4” 5 –––– 6 Flatwasher 3/8” 6 –––– 6 Lockwasher 3/8” 7 –––– 6 Hex Nut 3/8” 8 50061049 1 Bush Hog Decal 9 70419 1 Cotter Pin 10 –––– 2 Capscrew 3/8” x 1” 11 –––– 2 Lockwasher 3/8” 12 50031959 1 Push Over Assembly 13 D614 1 Decal, Danger 14 D546 1 Decal, Danger 15 70418 1 Castle Nut 16 76664 1 Blank Washer 17 70997 1 Gearbox, 540 RPM (3710, 3715) 70999 1 Gearbox, 1000 RPM (13710, 13715, 3715 Brush Cutter)


18 44510BH 6 Capscrew 3/4” x 2-1/2” Gr.8 19 20299 6 Locknut 3/4” Flanged 20 21020614 3 Cotter Pin 3/16” x 1-1/2” 21 50029783 1 Pin Assembly 22 15908BH 2 Flatwasher 1” 23 99564 1 Wing Lift Cylinder 24 95425 1 Pin 25 50057347 1 Round Pan Weldment 5’ 26 7555BH 2 Blade, CCW 97032BH 2 Blade, CCW, High Lift 27 63607 1 Blade Bolt Kit 28 7919BH 2 Blade Bolt 29 20322 2 Lockwasher 30 252BH 2 Jam Nut 31 D551 1 Blade Rotation Decal CCW 32 50031212 1 Reflector, Amber

RIGHT HAND WING ASSEMBLYModels 3710, 3715 & 3715 Brush Cutter

540 RPM13710 & 13715 – 1000 RPM

3029

28

91615

26

27

26

25

23

18

13

3231

13

1

14

12

10

2022

22 21198

2

4, 5, 6, 7

3

17

1120

24



71-1-3


1 50028748 1 Wing Frame w/ Decals, L.H. 50028752 1 Wing Frame (w/ Rings) w/ Decals, L.H. 2 50040099 1 Front Skid, L.H. 3 50040101 1 Rear Skid, L.H. 4 3161212 6 Plow Bolt 3/8” x 1-1/4” 5 –––– 6 Flatwasher 3/8” 6 –––– 6 Lockwasher 3/8” 7 –––– 6 Hex Nut 3/8” 8 50061049 1 Bush Hog Decal 9 70419 1 Cotter Pin 10 –––– 2 Capscrew 3/8” x 1” 11 –––– 2 Lockwasher 3/8” 12 50031959 1 Push Over Assembly 13 D614 2 Decal, Danger 14 D546 1 Decal, Danger 15 70418 1 Castle Nut 16 76664 1 Blank Washer


17 70996 1 Gearbox, 540 RPM (3715) 70998 1 Gearbox, 1000 RPM (13715, 3715 Brush Cutter) 18 44510BH 6 Capscrew 3/4” x 2-1/2” Gr.8 19 20299 6 Locknut 3/4” Flanged 20 21020614 3 Cotter Pin 3/16” x 1-1/2” 21 50029783 1 Pin Assembly 22 15908BH 2 Flatwasher 1” 23 99564 1 Wing Lift Cylinder 24 95425 1 Pin 25 50057347 1 Round Pan Weldment 5’ 26 11150 2 Blade, CW 97033BH 2 Blade, CW, High Lift 27 63607 1 Blade Bolt Kit 28 7919BH 2 Blade Bolt 29 20322 2 Lockwasher 30 252BH 2 Jam Nut 31 D552 1 Blade Rotation Decal CW 32 50031212 1 Reflector, Amber

LEFT HAND WING ASSEMBLYModel 3715, 3715 Brush Cutter – 540 RPM

13715 – 1000 RPM

1

13

14

31

24

20

23

10, 11

20

19

17

12

22

22

18

43

2

16

15

26

25

269

765

8

20

21

13

3029

28

27

32



71-1-4


1 50031399 1 Side Band Assembly 2 50031385 1 Removable Skid 3 50061049 1 Bush Hog Decal 4 3161212 8 Clipped Sq. Hd. Bolt 3/8” x 1-1/4” 5 –––– 10 Flatwasher 3/8” 6 –––– 10 Lockwasher 3/8” 7 –––– 10 Hex Nut 3/8” 8 50031214 1 Red Reflector 9 50031212 2 Amber Reflector 10 87052 2 Eye Bolt 11 –––– 1 Capscrew 1” x 3-3/4” 12 –––– 1 Lockwasher 1” 13 –––– 5 Hex Nut 1” 14 50069118 1 Hinge Pin 15 50029759 1 Hinge Connector 16 –––– 2 Capscrew 3/8” x 2” 17 –––– 2 Flatwasher 3/8” 18 20363 2 Locknut 3/8” 19 50028476 1 Latch 20 –––– 1 Capscrew 3/4” x 2-1/2” 21 20638 1 Locknut 3/4” 22 84672 1 Pin 23 1273BH 1 Presto Pin 24 44286 2 Carriage Bolt 3/8” x 1-1/2” 25 90993 1 Chain Weldment 26 –––– 1 Lockwasher 3/4” 27 –––– 1 Flatwasher 3/4” 28 50038099 1 Bushing

SIDE BAND ASSEMBLYModel 3710 – 540 RPM

13710 – 1000 RPM

1

2

3

765

4

9

24

76

5

25

14

14

20

2726

21

28 10

13

16

11

12 13

138

9

10

17

18

15

Old Style Wing Latch

20

22

21

19 23



71-2-1


1 50033596 1 Chain Assembly, Center Front, Single 50033597 1 Chain Assembly, Center Front, Double 2 50033600 2 Chain Assembly, Center Side, Single 50033601 2 Chain Assembly, Center Side, Double 3 50033590 1 Chain Assembly, Wing Front, Single L.H. 50033594 1 Chain Assembly, Wing Front, Single R.H. (Not Shown) 50033591 1 Chain Assembly, Wing Front, Double L.H. 50033595 1 Chain Assembly, Wing Front Double R.H. (Not Shown) 4 50033599 1 Support, Center Front Chain 5 50017211 A/R Chain, 6 Link, Single 50017213 A/R Chain, 11 Link, Double 6 50017210 A/R Spiral Pin 1/8” x 1-1/4” 7 50033598 1 Pin, Front Center Chain 8 50033603 2 Support, Center Side Chain 9 50033602 2 Pin, Center Side Chain 10 50017264 6 Chain, 5 Link 11 50033589 1 Support, Wing Front Chain L.H. 50033593 1 Support, Wing Front Chain R.H. (Not Shown) 12 50033592 2 Pin, Wing Front Chain 13 50029828 1 Chain Baffle Assembly, R.H. Front (Not Shown) 50029831 1 Chain Baffle Assembly, L.H. Front 14 50029825 2 Chain Bar, Short 15 44534BH 4 Carriage Bolt 3/8” x 1-3/4” 16 50029833 4 Spacer 3/4” 17 –––– 50 Flatwasher 3/8” 18 9131200 10 Locknut 3/8” 19 44286 51 Carriage Bolt 3/8” x 1-1/2” 20 –––– 40 Lockwasher 3/8” 21 –––– 40 Hex Nut 3/8”

FRONT CHAIN ASSEMBLYFor Models 3710, 3715 & 3715 Brush Cutter – 540 RPM

13710 & 13715 – 1000 RPM

1 2 3

6

5

9

87

5

22 22

22,17,21,20

17

17

20

21

12

11

5

13

19, 17, 18

10

14

161517

18

6

4

21

206

A/R – As RequiredNote: Left hand versions of wing chain assemblies and wing chain support not used on models 3710 or 13710.



71-2-2

REAR CHAIN ASSEMBLYModels: 3710, 3715 & 3715 Brush Cutter

– 540 RPM13715 & 13710 – 1000 RPM


1 50029846 1 Center Rear Chains, Single 50029847 1 Center Rear Chains, Double 2 50029820 1 Outer Chain Assy., R.H. Single 50029777 1 Outer Chain Assy., R.H. Double 50029821 1 Outer Chain Assy., L.H. Single 50029778 1 Outer Chain Assy., L.H. Double 3 50029822 2 Short Wing Chain Assy., Single 50029779 2 Short Wing Chain Assy., Double 4 50029823 2 Inner Wing Chain Assy., Single 50029780 2 Inner Wing Chain Assy., Double 5 50029804 2 Rear Wing Chain Assy., Single 50029782 2 Rear Wing Chain Assy., Double 6 50029827 1 Chain Baffle, R.H. Inside 50029830 1 Chain Baffle, L.H. Inside (Shown) 7 50029829 1 Chain Baffle, R.H. Outside (Shown) 50029832 1 Chain Baffle, L.H. Outside 8 50068157 1 Left Outside Support 9 50068160 1 Left Center Support 10 50068163 1 Left Inside Support 11 50068154 1 Rear Center Support 12 50068162 1 Right Inside Support 13 50068159 1 Right Center Support 14 50068156 1 Right Outside Support 15 50029845 1 Rear Center Pin 16 50017210 16 Spiral Pin 1/8” x 1-1/4” 17 50029811 42 Chain, 3 Link, Single 50017264 42 Chain, 5 Link, Double 18 50017211 39 Chain, 6 Link, Single 50017213 39 Chain, 11 Link, Double 19 50018912 34 Chain, 4 Link, Single 50017212 34 Chain, 7 Link, Double 20 50029762 2 Outer Retaining Rod 21 50029815 1 Outer Chain Weldment, R.H. 50029755 1 Outer Chain Weldment, L.H.


22 50017212 2 Chain, 7 Link 23 50028794 2 Rear Center Chain Support 24 50028785 2 Rear Center Pin 25 50029713 2 Chain Holder, Inner Wing 26 50029766 2 Rear Inside Pin 27 50017264 52 Chain, 5 Link, Single 50029803 52 Chain, 9 Link, Double 28 50029714 2 Chain Holder, Center Wing 29 50029769 2 Rear Wing Pin 30 50029825 2 Chain Bar, Short 31 50029826 2 Chain Bar 32 44286 66 Carriage Bolt 3/8” x 1-1/2” 33 –––– 4 Capscrew 3/8” x 2-1/2” 34 50029833 4 Spacer 3/4” 35 9131200 26 Locknut 3/8” 36 –––– 71 Flatwasher 3/8” 37 –––– 45 Lockwasher 3/8” 38 –––– 45 Hex Nut 3/8”

6

30

17 17

17

17

1818

1818

181

27

5

2

3219

22

383736

2021

1629

34

7

19

17 31

28

3 4

25

26

23

1616

89

1011

12

131415

24

27

32,36,35

32,36,35

32,36,37,38

32,36,37,38

32,36,37,38

32,36,37,38

33,36,3532,36,35

32,36,35

L. H. Rear

Center

R. H. Rear



71-2-3

FRONT BELTING ASSEMBLYFor Models 3710, 3715 & 3715 Brush Cutter – 540 RPM

13710 & 13715 – 1000 RPM


1 50028428 2 Belting, Wing 2 50028427 4 Belting Cover, Wing 3 50028426 1 Belting, Center 4 91326 2 Belting Cover, Center 5 50028424 2 Belting, Outside Center 6 50028423 4 Belting Cover, Outside Center 7 44534BH 40 Carriage Bolt 3/8” x 1-3/4” 8 –––– 40 Flatwasher 3/8” 9 –––– 40 Lockwasher 3/8” 10 ––– 40 Hex Nut 3/8”

4

4

3

51

2

26

6

1

7, 8, 9, 107, 8, 9, 10

7, 8, 9, 10



71-2-4


1 50029853 1 Outside Band, L.H. 2 50029852 1 Inside Band, L.H. 3 50029851 1 Center Band 4 50029850 1 Inside Band, R.H. 5 50029849 2 Wing Center Band 6 50029848 1 Outside Band, R.H. 7 5161212 A/R Carriage Bolt 3/8” x 1-1/4” (3715 & 13715) 44286 A/R Carriage Bolt 3/8” x 1-1/2” (3710 & 13710) 8 –––– A/R Flatwasher 3/8” 9 –––– A/R Lockwasher 3/8” 10 –––– A/R Hex Nut 3/8”

REAR BAND ASSEMBLYModels: 3710, 3715 & 3715 Brush Cutter – 540 RPM

13710 & 13715 – 1000 RPM(3710 & 13710 Use Center & R.H. Side Bands Only)

1

7

7

8

8

9

9

10

10

3

4

7, 8, 9, 10

7, 8, 9, 10

7, 8, 9, 1056 7

8910

5

27, 8, 9, 10

7, 8, 9, 10

L. H. Side

R. H. Side

Center

7, 8, 9, 10



71-2-5


1 50028749 1 Shield w/ Decals 2 50029721 1 Shield Mount Weldment 3 50028494 1 Center Gearbox Shield 4 50028493 1 Hinge Pin 5 –––– 2 Flatwasher 7/16” 6 21020406 2 Cotter Pin 1/8” x 3/4” 7 –––– 2 Capscrew 3/8” x 1” 8 9131200 2 Locknut 3/8” 9 91443 1 Important Decal 10 87317 1 Drawbar Decal 11 87340 1 Important Decal 12 50028366 1 Warranty Decal 13 69391 1 Lynch Pin 14 50028753 2 Model Decal, 3715 50029869 2 Model Decal, 3710 50067806 2 Model Decal 13710 50067807 2 Model Decal 13715


15 50018166 4 Capscrew M10 x 20 16 50038589 4 Capscrew w/ Patch M10 x 45 17 44198 8 Lockwasher M10 18 –––– 8 Flatwasher 3/8” 19 50035829 1 Owner’s Manual Tube 20 50035830 1 Manual Cap Seal 21 N/A 1 Manual Holder Cap 22 –––– 3 Capscrew 1/4” x 7/8” 23 –––– 6 Flatwasher 1/4” 24 –––– 3 Lockwasher 1/4” 25 –––– 3 Hex Nut 1/4”

CENTER SHIELD ASSEMBLY (OLD STYLE)(FOR REPLACEMENT OF COMPLETE SHIELD ASSEMBLY ORDER 50067568)

3710, 3715 & 3715 Brush Cutter – 540 RPM13710 & 13715 – 1000 RPM

147

17

18

15

8

4

5

5

6

6

2

16

17

13

20 21

19

2223

232425

3

1

12

9

1110



71-2-6


1 50029748 1 Wing Shield Weldment 2 50029749 1 Shield Mount Weldment 3 50018318 1 Retainer Bar Weldment 4 50018166 4 Capscrew M10 x 1.5 x 20 5 –––– 4 Flatwasher 3/8” 6 44198 4 Lockwasher M10 7 –––– 2 Capscrew 1/2” x 1-1/2” 8 –––– 2 Lockwasher 1/2” 9 –––– 2 Hex Nut 1/2” 10 50029752 1 Hinge Pin 11 69391 1 Lynch Pin 12 –––– 2 Cotter Pin 1/8” x 1”

OLD STYLE WING SHIELD ASSEMBLY3710, 3715 & 3715 Brush Cutter – 540 RPM

13710 & 13715 – 1000 RPM

50062091NEW STYLE WING SHIELD ASSEMBLY

3710, 3715 & 3715 Brush Cutter – 540 RPM13710 & 13715 – 1000 RPM

9

8

7

3

2

1110

12

12

1

4 5 6



71-2-7


1 50066171 1 Shield Mount Weldment 2 50054386 1 Rear Shield 3 50067564 1 Shield w/Decals 3715 50067565 1 Shield w/Decals 3710 50067855 1 Shield w/Decals13710 50067856 1 Shield w/Decals 13715 4 69391 1 Lynch Pin 5 50066174 1 Mounting Bracket Weldment 6 ------------- 4 Lockwasher 1/2” 7 ------------- 4 Hex Nut 1/2” 8 ------------- 4 Flatwasher 1/2” SAE 9 ------------- 4 Capscrew 1/2” x 1-1/4 Gr.5


10 ------------- 2 Capscrew 3/8” x 1” Gr.5 11 9131200 2 Locknut 3/8” 12 50028493 1 Hinge Pin 13 ------------ 2 Flatwasher 3/8” 14 ------------ 2 Cotter Pin 1/8”x 1” 15 91443 1 Decal, Important 16 87317 1 Decal, Drawbar (Used On Earlier Ver.) 17 87340 1 Decal, Important 18 50028753 2 Model Decal, 3715 50029869 2 Model Decal, 3710 50067806 2 Model Decal 13710 50067807 2 Model Decal 13715

1

8

9

14

15

16

17

18

1213

13

14

1110

2

3

4

5

6

7

50067568 CENTER SHIELD ASSEMBLY



71-3-1

8

10

12

5 4

2

45

16

7

15

1

9

6

1

43

5, 13

6

7

1

54 4

3 3

3451

11

NOTE: BEFORE ORDERING PARTS FOR THIS GEARBOX FIRST DETERMINE IF THE GEARBOX IS A COMER OR A BONDIOLI &PAVESI MANUFACTURED GEARBOX ASSEMBLY. DETERMINE THIS FROM THE ID TAG ON TOP OF THE GEARBOX HOUSING.

MODEL 3715 & 3710 (540 RPM)71202 TRANSFER GEARBOX ASSEMBLY. - 540 RPM

MFG. BY COMER

MODEL 13715 & 13710 (1000 RPM)71203 TRANSFER GEARBOX ASSEMBLY - 1000 RPM

MFG. BY COMER


1 70796 6 Bearing 2 76671 1 Casing 3 50068116 4 Oil Seal 4 70881 6 Snap Ring 5 70752 6 Shim .3 6 50076037 1 Gear, Kit (540 RPM) 1 - 24T & 2 - 20T Gears 50076038 1 Gear,Kit(1000 RPM) 2 - 24T & 1 - 20T Gears 7 76673 2 Shaft 1-3/4” Z20 8 80538 1 Vent Plug 9 76675 1 Shaft, 1-3/4” Z20 10 76676 1 Cover 11 44489BH 6 Capscrew M10 x 1.5 x 35 Gr.8.8 12 70181 2 Gas Plug 3/8” 13 70753 6 Shim .4 70754 6 Shim .5 70755 6 Shim .6



71-3-2


22 70740 1 Spacer 23 70722 1 Snap Ring 24 76634 1 Shim, 1mm 25 70753 1 Shim, .4mm 26 70754 1 Shim, .5mm 27 70755 1 Shim, 1mm 28 70345BH 1 Shim, .5mm 29 70346BH 1 Shim, 1mm 30 70347 1 Shim, .4mm 31 76664 1 Blank Washer 32 70418 1 Castle Nut M36 33 70419 1 Cotter Pin

70996 GEARBOX ASSEMBLY540 RPM, Ratio 1:1.60

Center; 3715, 3710L.H. Wing, 3715

Manufactured by Comer

71198 GEARBOX ASSEMBLY1000 RPM, Ratio 1:.82Center; 13715, 13710

Manufactured by Comer


L.H. Wing; 13715, 3715 Brush CutterManufactured by Comer / EG

206

73

11

19

9

24 17

16

15

14

32

31

30292810

2

13

33

5

12

18

8

1

23 21

223

64

7

25

2627


1 76658 1 Casting 2 76665 1 Gear, Ouput, 15 Teeth (70996) 76668 1 Gear, Ouput, 22 Teeth (71198) 76667 1 Gear, Ouput, 18 Teeth (70998) 3 70796 2 Bearing 4 50068116 1 Oil Seal 5 76659 1 Input Shaft 1-3/4” 6 70189 2 Snap Ring 7 70752 2 Shim .3mm 8 76660 1 Top Plate 9 70586 1 Castle Nut 10 70344 1 Shim .3mm 11 70292 1 Oil Filler Plug 1/2” Gas 12 44595BH 4 Capscrew M10 x 14 Gr.8.8 13 70800 1 Bearing 14 76661 1 Protective Washer 15 50062245 1 Oil Seal 16 70410 1 Bearing 17 76663 1 Shaft, Output 18 80538 1 Vent Plug 19 70585 1 Cotter Pin 20 70725 1 Cap 21 76666 1 Gear, Input, 24 Teeth (70996) 76667 1 Gear, Input, 18 Teeth (71198) 76668 1 Gear, Input, 22 Teeth (70998)



71-3-3


R.H. Wing; 3715 & 3710Manufactured by Comer / EG

70999 GEARBOX ASSEMBLY1000 RPM, Ratio 1:1.22R.H. Wing; 13715, 13710

& 3715 Brush CutterManufactured by Comer / EG

206

73

11

19

9

24 17

16

15

14

32

31

30292810

2

13

33

5

12

18

8

1

2321

223

64

7

2526

27


24 76634 1 Shim, 1mm 25 70753 1 Shim, .4mm 26 70754 1 Shim, .5mm 27 70755 1 Shim, 1mm 28 70345BH 1 Shim, .5mm 29 70346BH 1 Shim, 1mm 30 70347 1 Shim, .4mm 31 76664 1 Blank Washer 32 70418 1 Castle Nut M36 33 70419 1 Cotter Pin


1 76658 1 Casting 2 76665 1 Output Gear, 15 Teeth (70997) 76667 1 Output Gear, 18 Teeth (70999) 3 70796 2 Bearing 4 50068116 1 Oil Seal 5 76659 1 Input Shaft 1-3/4” 6 70189 2 Snap Ring 7 70752 2 Shim .3mm 8 76660 1 Top Plate 9 70586 1 Castle Nut 10 70344 1 Shim .3mm 11 70292 1 Oil Filler Plug 1/2” Gas 12 44595BH 4 Capscrew M10 x 14 Gr.8.8 13 70800 1 Bearing 14 76661 1 Protective Washer 15 50062245 1 Oil Seal 16 70410 1 Bearing 17 76663 1 Shaft, Output 18 80538 1 Vent Plug 19 70585 1 Cotter Pin 20 70725 1 Cap 21 76666 1 Input Gear, 24 Teeth (70997) 76668 1 Input Gear, 22 Teeth (70999) 22 70740 1 Spacer 23 70722 1 Snap Ring


71-3-4

NOTE: BEFORE ORDERING PARTS FOR THIS GEARBOX FIRST DETERMINE IF THE GEARBOX IS A COMER OR A BONDIOLI & PAVESI MANUFACTURED GEARBOX ASSEMBLY. DETERMINE THIS FROM THE ID TAG ON TOP OF THE GEARBOX HOUSING.

MODEL 3715 & 3710 (540 RPM)50045696 TRANSFER GEARBOX ASSEMBLY. - 540 RPM

REPLACED BY 71202 GEAERBOX ASSY.MFG. BY BONDIOLI & PAVESI

MODEL 13715 & 13710 (1000 RPM)50045697 TRANSFER GEARBOX ASSEMBLY - 1000 RPM

MFG. BY BOBDIOLI & PAVESI


1 50066914 1 Top Cover 2 50066915 1 Drain Plug (Magnetic) 3 50066917 2 Out Put Shafts 1-3/4” 20 Spline 4 50066918 4 Oil Seal 5 50066919 4 Snap Ring 85 x 4 mm 6 50066920 4 Shim Kit 7 70797 2 Bearing 35 x 72 x 18.25mm 8 50066922 1 Housing 9 50066923 1 Input Shaft 10 50066924 1 Breather Plug (Gas) 3/8” 11 50066925 6 Capscrew m10 x 22 x 1.5 c8.8 12 50066916 1 Gear Set for 540 RPM Gearbox 50045696 (Two 19 tooth gears and One 23 tooth gear) 50066926 1 Gear Set for 1000 RPM Gearbox 50045697 (Two 23 tooth gears and One 19 tooth gear) 13 44198 6 Lockwasher m10 14 70796 4 Bearing

1

4

5

6

14

14

8

9

12

14

6

5

7 7

1212

3

14

6

5

4

4

111013

14

3

6

5

4




71-4-1


1 76239BH 1 Complete Yoke 2 64963 2 Cross Journal Set 3 63956 2 Grease Nipple 4 76361 1 Complete Disc Clutch 5 76244 1 Guard Retaining Collar, Outer Tube 6 87992 6 Bolt 7 76245 1 Guard Retaining Collar, Inner Tube 8 64814 2 Safety Chain 9 76788 1 Complete Guard 10 44154BH 8 Lock Nut M10 11 76247 2 Tapered Pin Set 1-3/4” 12 76080 8 Spring 13 76331 1 Flanged Yoke


13 76331 1 Flanged Yoke 14 76082 1 Bushing 15 76083 4 Lining Ring 16 76458 1 Clutch Support 17 76085 2 Inner Plate 18 76197 1 Intermediate Plate 19 76086 1 Pressure Plate 20 44159BH 8 Capscrew M10 x 1.5 x 100 G8.8 21 76789 1 Female Tube w/ Yoke and Lube 22 76790 1 Male Tube w/ Yoke and Lube 23 76791 1 Half Female Shaft w/ Guarding 24 76792 1 Half Male Shaft w/ Guarding 25 78786 1 Danger Decal, Outer Tube 26 78608 1 Danger Decal, Outer Shield Tube

76635 DRIVESHAFT ASSEMBLY WITH CLUTCH Wing Driveshaft – ASAE Size 51000 RPM – 1-3/4” – 20 Spline Manufactured by Comer / EG

Used on 3710, 3715, 13710, 13715, 3715 Brush Cutter Replaced by 50058537 Driveshaft Assembly

10 12 13

14

11

5

6 6

726

8

21 2252122

15 16 11 15 181517 17 19 2015

3 324

23 9



71-4-2


1 76782 1 Yoke w/ Grease Nipple 2 76696 2 Cross Journal Set 3 76965 4 Capscrew M12 x 1.25 x 90, Gr. 12.9 w/ Locknut M12 4 44154BH 8 Lock Nut M10 5 76305 1 Flanged Yoke, Male 6 76306 1 Retaining Washer 7 76307 1 Flanged Yoke, Female 8 76456 1 Complete Disc Clutch 9 63946 1 Grease Nipple 10 76080 8 Spring 11 76164 1 Flanged Yoke 12 76082 1 Bushing 13 76083 4 Lining Ring 14 76247 1 Tapered Pin Set 1-3/4” 15 76458 1 Clutch Support 16 76085 2 Inner Plate 17 76197 1 Intermediate Plate 18 76086 1 Pressure Plate 19 44159BH 8 Capscrew M10 x 1.5 x 100 G8.8

76636 DRIVESHAFT ASSEMBLY WITH CLUTCHCenter Driveshaft – ASAE Size 4

1000 RPM – 1-3/4” – 20 SplineManufactured by Comer / EG

Used on 3710, 3715, 3715 Brush Cutter, 13710, 13715Replaced by 50058536 Driveshaft

10 11

1213 15

1413

13 17 1316 16 18 19

1 23

4

5 6 7

2

8

9



71-4-3


1 50017504 1 Complete Collar Yoke 2 76356 2 Cross Journal Set 3 76579 3 Grease Nipple 4 76357 1 Wide Angle Double Yoke 5 76604 1 Cross Journal Set 6 76239BH 1 Complete Yoke 7 76362 6 Screw Kit 8 76363 1 Bearing Ring 9 76244 1 Guard Retaining Collar for Outer Tube 10 87992 6 Bolt 11 76245 1 Guard Retaining Collar for Inner Tube 12 64814 3 Safety Chain 13 76950 1 Guard Cone Set 14 76944 1 Complete Guard 15 76247 1 Tapered Pin Set 1-3/4” 16 76762 1 Female Tube w/ Yoke & Lube System 17 76896 1 Yoke 18 76898 1 Outer Tube w/ Decal 19 76897 1 Wiper 20 67108 1 Roll Pin 21 76899 1 Plastic Cap 22 76763 1 Male Tube w/ Yoke & Lube System 23 76945 1 Half Female Shaft w/ Guarding 24 76765 1 Half Male Shaft w/ Guarding 25 78786 1 Danger Decal for Outer Tube 26 78608 1 Danger Decal for Outer Guard Tube 27 50017480 1 Ball Collar kit 1-3/8”


1 50017482 1 Complete Collar Yoke 2 76420 2 Cross Journal Set 3 76579 3 Grease Nipple 4 76421 1 Wide Angle Double Yoke 5 64663 1 Cross Journal Set 6 76422 1 Complete Yoke 7 76362 6 Screw Kit 8 76423 1 Bearing Ring 9 76057 1 Guard Retaing Collar for Outer Tube 10 87992 6 Bolt 11 76059 1 Guard Retaining Collar for Inner Tube 12 64814 3 Safety Chain 13 76933 1 Guard Cone Set 14 76946 1 Complete Guard 15 76247 1 Tapered Pin Set 1-3/4” 16 76772 1 Female Tube w/ Yoke & Lube System 17 76893 1 Yoke 18 76904 1 Outer Tube w/ Decal 19 76894 1 Wiper 20 66866 1 Roll Pin 21 76892 1 Plastic Cap 22 76773 1 Male Tube w/ Yoke & Lube System 23 76947 1 Half Female Shaft w/ Guarding 24 76775 1 Half Male Shaft w/ Guarding 25 78786 1 Danger Decal for Outer Tube 26 78608 1 Danger Decal for Outer Guard Tube 27 50017480 1 Ball Collar kit 1-3/8”

76530 C.V. DRIVESHAFTASAE Size 5, 540 RPM – 1-3/8”– 6 Spline

Manufactured by Comer / EGModels: 3710, 3715, 3715 Brush Cutter

May substitute 87751 DriveshaftReplaced by 50054510 Driveshaft

76532 C.V. DRIVESHAFTASAE Size 4, 1000 RPM – 1-3/8” – 21 Spline

Manufactured by Comer / EGModels: 13710 & 13715


27

12

26

1210 10

98

137

16 22 56

11

1520 18

2521

2 4

33 3

23 24

14

17 19



71-4-4


1 50017503 1 Complete Collar Yoke 2 76356 2 Cross Journal Set 3 76579 3 Grease Nipple 4 76357 1 Wide Angle Double Yoke 5 76604 1 Cross Journal Set 6 76239BH 1 Complete Yoke 7 76362 6 Screw Kit 8 76363 1 Bearing Ring 9 76244 1 Guard Retaining Collar for Outer Tube 10 87992 6 Bolt 11 76245 1 Guard Retaining Collar for Inner Tube 12 64814 3 Safety Chain 13 76950 1 Guard Cone Set 14 76953 1 Complete Guard 15 76247 1 Tapered Pin Set 1-3/4” 16 76757 1 Female Tube w/ Yoke & Lube System 17 76896 1 Yoke, Outer 18 76903 1 Outer Tube, Complete 19 76897 1 Wiper 20 67108 1 Roll Pin 21 76899 1 Cap, Outer Tube 22 76758 1 Male Tube w/ Yoke & Lube System 23 76954 1 Half Female Shaft w/ Guarding 24 76760 1 Half Male Shaft w/ Guarding 25 78786 1 Danger Decal for Outer Tube 26 78608 1 Danger Decal for Outer Guard Tube 27 50017480 1 Ball Collar Kit 1-3/8”


1 50017501 1 Complete Collar Yoke 2 76420 2 Cross Journal Set 3 76579 3 Grease Nipple 4 76421 1 Wide Angle Double Yoke 5 64663 1 Cross Journal Set 6 76422 1 Complete Yoke 7 76362 6 Screw Kit 8 76423 1 Bearing Ring 9 76057 1 Guard Retaing Collar for Outer Tube 10 87992 6 Bolt 11 76059 1 Guard Retaining Collar for Inner Tube 12 64814 3 Safety Chain 13 76933 1 Guard Cone Set 14 76955 1 Complete Guard 15 76247 1 Tapered Pin Set 1-3/4” 16 76767 1 Female Tube w/ Yoke & Lube System 17 76893 1 Yoke, Outer 18 76895 1 Outer Tube, Complete 19 76894 1 Wiper 20 66866 1 Roll Pin 21 76892 1 Cap, Outer Tube 22 76768 1 Male Tube w/ Yoke & Lube System 23 76956 1 Half Female Shaft w/ Guarding 24 76770 1 Half Male Shaft w/ Guarding 25 78786 1 Danger Decal for Outer Tube 26 78608 1 Danger Decal for Outer Guard Tube 27 50017502 1 Ball Collar Kit

76647 C.V. DRIVESHAFTASAE Size 5, 1000 RPM – 1-3/8”– 21 Spline

Manufactured by Comer / EGModels: 13710, 13715


76649 C.V. DriveshaftASAE Size 4, 1000 RPM – 1-3/4” – 20 Spline

Manufactured by Comer / EGModels: 13710, 13715


27

1

2

26

1210 10

98

137

1622

56

11

152 4

33 3

23 24

14

2018

2521

17 19



71-4-5


1 86549 1 Front Half Assy. 1 3/8”-21 Sp. Yoke 86725 1 Front Half Assy. 1 3/4”-20 Sp. Yoke 2 86550 1 Rear Half Assy. 1 3/8” Yoke 86726 1 Rear Half Assy. 1 3/4” Yoke 3 86551 1 Safety Guard for 1 3/8”Yoke 86727 1 Safety Guard for 1 3/4” Yoke 4 50068914 1 Yoke Assy. 1 3/8” - 21Spline 93580 1 Yoke Assy. 1 3/4” - 20 Spline 5 50064645 1 Sleeve & Ball Kit for 1 3/8” Yoke 93700 1 Sleeve & Ball Kit for 1 3/4” Yoke 6 63956 3 Grease Fitting 7 86511 2 Cross Bearing Kit 8 86512 1 C.V.Central Body 9 63946 1 Grease Fitting 10 86513 1 Yoke (Outer Tube) 11 66866 1 Flexible Pin 12 86547 1 Tube, Outer for 1 3/8” Yoke 86721 1 Tube, Outer for 1 3/4” Yoke


13 78608 1 Safety Decal 14 86331 1 Plastic Ring 15 86330 1 Grease Nipple 16 86753 1 C.V. Shielding Complete 17 86517 1 Ring Nut 18 66875 1 Outer Shield Bearing 19 64814 2 Chain 20 86546 1 Yoke 21 50053705 1 Pivot Pin Kit 22 44234BH 1 Hex Nut m14 23 44233BH 1 Lockwasher m14 24 64663 1 Cross Bearing Kit 25 66870 1 Inner Tube Yoke 26 66869 1 Flexible Pin 27 66876 1 Inner Shield Bearing 28 78786 1 Danger Decal 29 92962 1 Inner Tube for 1 3/8” Yoke 86722 1 Inner Tube for 1 3/4” Yoke

85001BH 80° C.V. DRIVESHAFT (INPUT) 1000 RPM 1 3/8” – 21 SPLINEASAE Size 4. Mfd. by Bondioli & Pavesi Replaced by 76785 Driveshaft Assembly

May substitute 76532 DriveshaftUsed on 13710, 13715

85002BH 80° C.V. DRIVESHAFT (INPUT) 1000 RPM 1 3/4” – 20 SPLINEASAE Size 4. Mfd. by Bondioli & PavesiReplaced by 76963 Driveshaft Assembly

May substitute 76649 DriveshaftUsed on 13710, 13715

© 2012 Alamo Group Inc.71-4-6

87751 80° C.V. DRIVESHAFT (INPUT)540 RPM 1 3/8” – 6 Spline, ASAE Size 5

Mfd. by Bondioli & PavesiReplaced by 76784 Driveshaft Assembly

May substitute 76530 Driveshaft, Mfd. by Comer/EGUsed on 3710, 3715, 3715 Brush Cutter


1 88035 1 Front Half Assy. w/ Shielding 2 88036 1 Rear Half Assy. w/ Shielding 3 88037 1 Safety Guard Assy. 4 93574 1 Yoke Assy. 1 3/8” - 6 Spline 5 93699 1 Sleeve & Ball Kit 6 63956 2 Grease Fitting 7 86529 2 Cross Bearing Kit 8 86530 1 Central Body 9 63946 2 Grease Fitting 10 88033 1 Yoke & Tube 11 78786 1 Danger Decal 12 86754 1 Complete Shell 13 86535 2 Ring Nut


14 68179 1 Outer Shield Bearing 15 64814 2 Chain 16 85414 1 Yoke Assy. 17 50053705 1 Pivot Pin Kit 18 44234BH 1 Hex Nut M14 x 1.5 19 44233BH 1 Lockwasher M14 20 64963 1 Cross Bearing Kit 21 68172 1 Yoke 22 68711 1 Spring Dowel 23 68180 1 Inner Shield Bearing 24 78608 1 Safety Decal 25 88034 1 Shaft, Splined 26 86531 1 Yoke




71-4-7


1 N/A 1 Half Shaft (Tractor End) 2 86538 1 Half Shaft (Rear) 3 86539 1 Safety Guard 4 93699 1 Q.D. Hub & Snap Ring 5 93698 1 Yoke 1-3/8” – 21 Spline (1000 RPM) 6 63956 3 Grease Fitting 7 86529 2 Cross Bearing Kit 8 86530 1 C.V. Central Body 9 63946 1 Grease Fitting 10 86531 1 Yoke (Outer Tube) 11 67108 1 Flexible Pin 12 86532 1 Tube, Outer 13 78786 1 Danger Decal 14 86534 1 Plastic Ring


15 86330 1 Grease Nipple 16 86754 1 Complete C.V. Shell 17 86535 2 Ring Nut 18 68179 1 Bearing, Outer Shield 19 64814 2 Chain 20 85414 1 Yoke (Implement) 21 50053705 1 Pivot w/ Nut & Lockwasher 22 44234BH 1 Hex Nut M14 x 2 23 44233BH 1 Lockwasher M14 24 64963 1 Cross Bearing Kit 25 67086 1 Yoke (Inner Tube) 26 67085 1 Flexible Pin 27 68180 1 Bearing, Inner Shield 28 78608 1 Danger Decal 29 86533 1 Inner Tube

86677 80° C.V. DRIVESHAFT (INPUT)Mfd. by Bondioli & Pavesi

1000 RPM – 1-3/8” – 21 Spline, Category 5, ASAE Size 5Replaced by 76964 Driveshaft Assembly

May substitute 76647 Driveshaft, Mfd. by Comer/EGUsed on 13710, 13715



71-4-8


1 89070 1 Stub Shaft, Tube & Yoke Weld. 2 1294BH 1 Cross Bearing Kit 3 60807 1 Yoke 1 3/4” - 20 Spline 4 19011 1 Capscrew 5/8” x 3 1/4” Gr.5 5 15563 1 Hex Nut 5/8” 6 19486 1 Lockwasher 5/8” 7 89071 1 Shield Assy. 8 1694BH 2 Shield Bearing 9 62848 1 Support Bearing 10 78608 1 Danger Decal 11 78786 1 Danger Decal

87603 JACKSHAFT ASSEMBLY (INPUT)ASAE Size 5

For Models Using Jackshaft InputManufactured by Walterscheid

Used on 3710, 3715, 3715 Brush Cutter, 13710, 13715



71-4-9

87636 DRIVESHAFT 540 RPM 1-3/8” – 6 Spline, ASAE Size 5

For 3715, 3710 & 3715 Brush Cutter Models Using Jackshaft InputManufactured by Walterscheid

87637 DRIVESHAFT1000 RPM 1-3/8” – 21 Spline, ASAE Size 5

For 13715 & 13710 Models Using Jackshaft InputManufactured by Walterscheid

87638 DRIVESHAFT 1000 RPM 1-3/4” – 20 Spline, ASAE Size 5

For 13715 & 13710 Models Using Jackshaft InputManufactured by Walterscheid


1 89099 1 Tractor Half Shaft (87636) 90001 1 Tractor Half Shaft (87637) 90003BH 1 Tractor Half Shaft (87638) 2 90000 1 Implement Half (87636, 87637) 90004 1 Implement Half (87638) 3 89088 1 Shield Assembly (87636) 89089 1 Shield Assembly (87637) 89090 1 Shield Assembly (87638) 4 87401 1 Yoke & Collar (87636) 87397 1 Yoke & Collar (87637) 89076 1 Yoke & Collar (87638) 5 50012426 1 Collar Kit (87636, 87637) 50012782 1 Collar Kit (87638) 6 1294BH 2 Cross Bearing Kit


7 89069 1 Yoke & Tube (87636) 89075 1 Yoke & Tube (87637) 11617 1 Yoke & Tube (87638) 8 78786 1 Shield Missing Decal 9 87316 2 Grease Fitting 10 60807 1 Implement Yoke 11 11375 1 Capscrew 5/8” x 3-1/4” Gr.5 12 15563 1 Hex Nut 5/8” 13 19486 1 Lockwasher 5/8” 14 89068 1 Yoke & Bar (87636, 87637) 11613 1 Yoke & Bar (87638) 15 1694BH 4 Shield Bearing 16 62848 1 Bearing Ring 17 78608 1 Danger Decal



71-4-10


1 87613 1 Spacer Weldment 2 50029706 1 Mount Weldment 3 88100 1 Shield 4 88927 1 Pin Weld. 5 87708 1 Spacer 6 87609 1 Pivot Spacer 7 –––– 2 Capscrew1/2” x 1 1/4” Gr.5 8 –––– 6 Lockwasher 3/4” 9 9162400 6 Locknut 3/4” 10 44182 1 Capscrew 3/4” x 9 1/2” Gr.5 11 –––– 2 Lockwasher 1/2” 12 –––– 4 Capscrew 3/4” x 4” Gr.5 13 90986 1 Pillow Block Bearing (14–18) 14 88916 2 Tension Bushing 15 77492 1 Snap Ring 16 77491 1 Bearing w/Collar 17 88840 1 Set Screw 18 90983 1 Spacer

PILLOW BLOCK ASSEMBLYFor Models Using Jackshaft Input

Used on 3715, 3710, 3715 Brush Cutter, 13715, 13710

7

11

4

16

14

14

1

1817

15

9

9

9

9

8

8

8

8 6

10

12

12

2

13

5

3


76784 CV DRIVESHAFT ASSEMBLY540 RPM, 1-3/8” X 6 SPLINE TRACTOR YOKE

ASAE SIZE 5MANUFACTURED BY BONDIOLI & PAVESI

(REPLACEMENT FOR 87751 CV DRIVESHAFT MFG. BY BONDIOLI & PAVESI)

Models: 540 RPM Models 3710 & 3715Replaced by 50047011 Driveshaft


1 71390 1 Yoke, CV 1-3/8” -6 Spline (Tractor) 2 71391 2 Cross Bearing Kit 3 63946 4 Grease Fitting 4 71392 1 Yoke w/Hub, Outer Tube 5 71393 1 Central Body 6 71394 1 Outer Cardan Tube 7 50053682 1 Inner Tube Assy. w/Lube Fitting 8 71396 1 Flexible Pin 9 71397 1 Flexible Pin 10 71398 1 Yoke, Inner Tube 11 71399 1 Cross Bearing Kit 12 71400 1 Tube Plug 13 71401 1 Yoke, 1-3/4”-20 Spline (Implement) 14 71440 1 Grease Fitting


15 71455 1 Outer Ring 16 71402 1 Ring for Inner Cone 17 71403 1 Ring 18 71404 17 Screw 19 71405 1 Chain 20 71447 1 Shield Tube Connecting Ring 21 78608 1 Danger Decal 22 78786 1 Danger Shield Missing 23 71406 1 Sleeve Kit 24 50053705 1 Pivot 25 71408 1 Outer Half Shaft 26 71409 1 Inner Half Shaft 27 71410 1 Complete Guard Assembly

71-4-11© 2012 Alamo Group Inc.


76785 CV DRIVESHAFT ASSEMBLY1000 RPM, 1-3/8” - 21 SPLINE TRACTOR YOKE



Used On: 1000RPM Models 3710 & 3715Replaced by 50053303




15 71448 1 Outer Ring 16 71402 1 Ring for Inner Cone 17 71438 1 Ring 18 71404 17 Screw 19 71405 1 Chain 20 71447 1 Shield Tube Connecting Ring 21 78608 1 Danger Decal 22 78786 1 Danger Shield Missing 23 50064645 1 Sleeve Kit 24 50053705 1 Pivot 25 N/A 1 Outer Half Shaft 26 71464 1 Inner Half Shaft 27 71458 1 Complete Guard Assembly



76963 CV DRIVESHAFT ASSEMBLY1000 RPM, 1-3/4”-20 SPLINE TRACTOR YOKE


(REPLACEMENT FOR 85002 CV DRIVESHAFT MFG. BY BONDIOLI & PAVESI)Used On: 1000RPM Models 3710 & 3715

Replaced by 50053305 Driveshaft




15 71448 1 Outer Ring 16 71402 1 Ring for Inner Cone 17 71438 1 Ring 18 71404 17 Screw 19 71405 1 Chain 20 71447 1 Shield Tube Connecting Ring 21 78608 1 Danger Decal 22 78786 1 Danger Shield Missing 23 71423 1 Sleeve Kit 24 50053705 1 Pivot 25 71461 1 Outer Half Shaft 26 71462 1 Inner Half Shaft 27 71463 1 Complete Guard Assembly



76964 CV DRIVESHAFT ASSEMBLY1000 RPM, 1-3/8”- 21 SPLINE TRACTOR YOKE



Used On:1000RPM Models 3710 & 3715Replaced by 50053306 Driveshaft


1 71465 1 Yoke, CV 1-3/8” -21 Spline (Tractor) 2 71391 2 Cross Bearing Kit 3 63946 4 Grease Fitting 4 71392 1 Yoke w/Hub, Outer Tube 5 71393 1 Central Body 6 N/A 1 Outer Cardan Tube 7 50053682 1 Inner Tube Assy. w/Lube Fitting 8 71396 1 Flexible Pin 9 71397 1 Flexible Pin 10 71398 1 Yoke, Inner Tube 11 71399 1 Cross Bearing Kit 12 71400 1 Tube Plug 13 71401 1 Yoke, 1-3/4”-20 Spline (Implement) 14 71440 1 Grease Fitting


15 71455 1 Outer Ring 16 71402 1 Ring for Inner Cone 17 71403 1 Ring 18 71404 17 Screw 19 71405 1 Chain 20 71447 1 Shield Tube Connecting Ring 21 78608 1 Danger Decal 22 78786 1 Danger Shield Missing 23 71406 1 Sleeve Kit 24 50053705 1 Pivot 25 71435 1 Outer Half Shaft 26 N/A 1 Inner Half Shaft 27 71410 1 Complete Guard Assembly




50047011 CV DRIVESHAFT ASSEMBLY540 RPM, 1-3/8”, 6 Spline Tractor Yoke

ASAE SIZE 5Mfr: Bondioli & Pavesi

Supersession: Replaced by 50053304 DriveshaftModels: 3710, 3715, 3715 Brush Cutter


1 71390 1 Yoke, CV 1-3/8” -6 Spline (Tractor) 2 71391 2 Cross Bearing Kit 3 63946 4 Grease Fitting 4 71392 1 Yoke w/Hub, Outer Tube 5 71393 1 Central Body 6 71394 1 Outer Cardan Tube 7 50053682 1 Inner Tube Assy. w/Lube Fitting 8 71396 1 Flexible Pin 9 66113 1 Flexible Pin 10 71398 1 Yoke, Inner Tube 11 71399 1 Cross Bearing Kit 12 71400 1 Tube Plug 13 50047636 1 Yoke, Shear Bolt (Implement) 14 71440 1 Grease Fitting


15 71455 1 Outer Ring 16 71402 1 Ring for Inner Cone 17 71403 1 Ring 18 71404 17 Screw 19 71405 1 Chain 20 71447 1 Shield Tube Connecting Ring 21 78608 1 Danger Decal 22 78786 1 Danger Shield Missing 23 71406 1 Sleeve Kit 24 50050694 1 Shear Bolt Kit 25 50047637 1 Pin 26 71408 1 Outer Half Shaft 27 N/A 1 Inner Half Shaft 28 71410 1 Complete Guard Assembly

71-4-15

3

21

15

4 6 7

9 12

1310

20

1816

17 18

15

18

23

18

2425

19

8

2211

14

3

2

28

131

26 27



1 50053719 1 Yoke, CV 1-3/8”, 21 Spline 2 50053718 1 Cross Bearing Kit 3 50053717 1 Yoke 4 50053716 1 Central Body 5 50053715 1 Roll Pin 6 50053698 1 Drive Tube, Outer 7 71418 1 Flexible Roll Pin, Inner 8 71419 1 Yoke, Inner Tube 9 50053697 1 Drive Tube, Inner 10 50053712 1 Yoke, 1-3/4”, 20 Spline 11 71420 1 Cross Bearing Kit 12 50053711 Shield Support, Outer 13 50053710 1 Shield Support


14 71404 12 Screw, Self-Tapping 15 71402 1 Shield Support, Inner 16 50053709 6 Washer 17 71447 1 Single Chain Restraint Collar 18 50053708 2 Screw 19 50053707 1 Shield Chain 20 78786 1 Danger Decal, Outer Tube 21 78608 1 Danger Decal, Shield 22 50053721 1 Ball Collar Kit 1-3/8” 23 50053705 1 Taper Pin Kit, 3 Pins 24 50053701 1 Half Shaft, Outer, Shielded 25 50053700 1 Half Shaft, Inner, Shielded 26 50053699 1 Complete Shield

50053303SP CV DRIVESHAFT ASSEMBLY1000 RPM, 1-3/8” – 21 Spline Tractor Yoke

ASAE Size 4Mfr: Bondioli & PavesiModels: 13710 & 13715

Supersession: Replaces 76785 Driveshaft

2

5 20 7

1 4 3 6 9 8 10

11

19

25

15

1818

17

2112

26

1324

14

14 14

16

22

1

23

10

71-4-16






14 71404 12 Screw, Self-Tapping 15 71402 1 Shield Support, Inner 16 50053709 6 Washer 17 50053707 1 Shield Chain 18 78786 1 Danger Decal, Outer Tube 19 78608 1 Danger Decal, Shield 20 50053721 1 Ball Collar Kit 1-3/8” 21 50053705 1 Taper Pin Kit, 3 Pins 22 50053687 1 Complete Shield


ASAE Size 5Mfr: Bondioli & Pavesi

Models: 3710, 3715 (540 RPM Models)Supersession: Replaces 50047011 Driveshaft

2

5 18 7

1 4 3 6 9 8 10

11

17

1519

12

22

13

14

14 14

16

20

1

21

10

71-4-17









Models: 3710L & 3715 (1000 RPM Models)Supersession: Replaces 76963 Driveshaft

2

5 20 7

1 4 3 6 9 8 10

11

19

25

15

1818

17

2112

26

1324

14

14 14

16

22

1

23

10

71-4-18




1 50053683 1 Yoke, CV 1-3/8” 21 Spline 2 50053677 1 Cross Bearing Kit 3 50053728 1 Yoke 4 50053727 1 Central Body 5 50053715 1 Roll Pin 6 71394 1 Drive Tube, Outer 7 71397 1 Flexible Roll Pin, Inner 8 71398 1 Yoke, Inner Tube 9 50053682 1 Drive Tube, Inner 10 50053723 1 Yoke, 1-3/4”, 20 Spline 11 71399 1 Cross Bearing Kit 12 50053711 Shield Support, Outer 13 50053722 1 Shield Support





Models: 13710 & 13715 (1000 RPM Models)Supersession: Replaces 76964 Driveshaft

2

5 20 7

1 4 3 6 9 8 10

11

19

25

15

1818

17

2112

26

1324

14

14 14

16

22

1

23

10

71-4-19




1 50017482 1 Complete Collar Yoke 2 50056414 2 Cross Journal Set 3 76335 3 Grease Nipple 4 76421 1 Wide Angle Double Yoke 5 76893 1 Outer Yoke 6 66866 1 Roll Pin For Outer Tube 7 76894 1 Wiper 8 76904 1 Complete Outer Tube 9 50056411

Sec 71 (3710,3715), Jan. 2019 Sec 71 (3710,3715) · 2020. 2. 21. · 17 70996 1 Gearbox, 540 RPM...

Documents

Transcript of Sec 71 (3710,3715), Jan. 2019 Sec 71 (3710,3715) · 2020. 2. 21. · 17 70996 1 Gearbox, 540 RPM...