Sec 67 (3414) - Bush Hog · 5 86666 66DoubleEdgeBlade 6 90563 –––– 1 MountWeldment 7 90537...

LAND MAINTENANCEREPAIR PARTS MANUAL

MODEL: 3414SECTION: 67

BUSH HOG®

2501 Griffin Ave. • Selma, AL 36703(334) 872-6261 • (334) 874-2700

Parts Ordering 1-800-304-2836Fax 1-800-572-1784

www.bushhog.com

BUSH HOG/ LAND MAINTENANCE REPAIR PARTS MANUAL

3414ROTARY CUTTERALPHABETICAL INDEX

CONTENTS PAGEAxle Weldment ..........................................................................................................................................67-1-1Axle Arm Assembly (Pull Models) .....................................................................................67-7-1 through 67-7-3Band, Rear (All Models) .............................................................................................................................67-3-2Belting, Front (Center Hitch Models).........................................................................................................67-3-2Belting, Rear ..............................................................................................................................................67-3-3Base Assembly ..........................................................................................................................................67-1-1Blades & Blade Holders ............................................................................................................................67-2-1Chain, Safety Tow......................................................................................................................................67-6-1Chains, Highway (All Models) ....................................................................................................................67-3-1Clevis, Tongue ...........................................................................................................................................67-6-1Cylinder, Hydraulic .....................................................................................................................................67-8-2Decals................................................................................................................................See Base AssembliesDeck Weldments ...............................................................................................................See Base AssembliesDriveline Shields, Old Style........................................................................................................................67-1-2Driveline Shields, New Style ......................................................................................................................67-1-3Driveshafts ......................................................................................................................67-5-2 through 67-5-12Gearbox, Assemblies ........................................................................................................67-4-1 through 67-4-3Hitch, 3 Point Lift & Semi-Mount ................................................................................................................67-6-2

Pull Type (Tongue) .............................................................................................................................67-6-1Holder, Hose ..............................................................................................................................................67-8-1Hub, Wheel (Pull Models)..................................................................................................67-7-1 through 67-7-3Hub, Wheel (Lift & Semi-Mount) ................................................................................................................67-7-4Hydraulic Components .................................................................................................................67-8-1, 67-8-2Jackstand...................................................................................................................................................67-6-1Ratchet Assy. .............................................................................................................................................67-8-1Pillow Block Bearing & Mount ....................................................................................................................67-5-1Rims...............................................................................................................................................67-7-3, 67-7-4Shredder Attachment .................................................................................................................................67-2-2Skids..................................................................................................................................See Base AssembliesStop Kits (Hydraulic Cylinder) ....................................................................................................................67-8-1Tailwheel Assembly (3 Pt. Lift & Semi-Mount) ...........................................................................................67-7-4Tires...............................................................................................................................................67-7-3, 67-7-4

July, 2011

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

REF. PARTNO. NO. QTY. DESCRIPTION

1 50031220 1 Axle Weldment w/ Reflectors2 90108 4 Bushing3 44250 2 Capscrew 1” x 10 1/2” Gr. 84 15821 2 Lockwasher 1”5 19502 2 Hex Nut 1”6 50018280 3 Reinforcing Pad7 –––– 12 Capscrew 3/4” x 2 1/2”8 20414 18 Flanged Hex Nut 5/8”9 50040394 1 L.H. Skid10 50040393 1 R.H. Skid11 50040391 2 Skid12 44928 10 Plow Bolt 3/8” x 1-1/2”13 –––– 10 Lockwasher 3/8”14 –––– 10 Flatwasher 3/8”15 –––– 10 Hex Nut 3/8”16 50026880 1 Deck w/Decals 540 RPM

50026881 1 Deck w/Decals 1000 RPM50026178 1 Decal Kit 540 RPM50026179 1 Decal Kit 1000 RPM

17 50061049 2 Bush Hog Decal18 50026175 1 Model Decal 3414

50067802 1 Model Decal 13414


19 D551 2 Blade Rotation Decal (CCW)20 D552 1 Blade Rotation Decal (CW)21 50031214 7 Red Reflector22 50031212 2 Amber Reflector23 90223 1 Baffle L.H.24 90224 1 Baffle R.H.25 –––– 12 Capscrew 1/2” x 1 1/4” Gr.526 –––– 12 Flatwasher 1/2”27 –––– 12 Lockwasher 1/2”28 –––– 12 Hex Nut 1/2”29 D549 1 General Hazard Decal30 D553 1 Warning Decal (Hyd Oil & Towing)31 –––– 6 Capscrew 3/4” x 2-3/4” (Center)32 50031219 5 Red / Orange Reflector33 D581 1 Lube Point Decal34 D614 4 Danger Decal ( Thrown Obj.)35 50028366 1 Warranty Decal36 D546 3 Danger Decal (Guard Missing)37 D547 1 Danger Decal (Driveline Entangle)

3414 BASE ASSEMBLY

67-1-1

1

32

32

32

32

32

21

21

21

21

21

45

2

3

68

8

7

9

10

11

12

151314

12

1314 15

16

17

1822

19

19

20

21

22

23

2930

31

29

30

21

27

28

2625

24

JULY, 2011

33

34

34

34

34

35

36

37


67-1-2


2 –––– 8 Flatwasher 3/8”3 50018166 8 Capscrew M10 ZP5 50032274 1 R.H. Shield Bracket6 50032275 1 L.H. Shield Bracket7 50032273 1 Cross Shaft Cover

DRIVELINE SHIELDING, OLD STYLEFor Model 3414

END VIEWCROSS SHIELDS & BRACKETS

9

1

4

89

10

6

5

1

1

7

32

23

50035717 SHIELD KITFor older style 3214 models

*Note: Some earlier 3414 models have a different style Cross ShaftCover. To replace older style Cross Shaft Covers, order 50035717Shield Kit, shown below. Measure shield to determine which style isneeded. (See diagram at left.)

9.54”

4.71”

10.54”

6.97”

OLD STYLECROSS SHIELD

OLD STYLESHIELD BRACKET

NEW STYLESHIELD BRACKET

NEW STYLECROSS SHIELD

7.12” 7.62”

5.00” 6.26”


1 20312 5 Lynch Pin2 –––– 20 Flatwasher 3/8”3 50018166 20 Capscrew M10 ZP4 50017584 1 Input Shield5 50032274 2 R.H. Shield Bracket, New Style

50017598 2 R.H. Shield Bracket,Pull & Semi-Mount, Old Style

50025543 2 R.H. Shield Bracket, Lift, Old Style6 50032275 2 L.H. Shield Bracket, New Style

50017597 2 L.H. Shield Bracket,Pull & Semi-Mount, Old Style

50025544 2 L.H. Shield Bracket, Lift, Old Style7 50032273 2 Cross Shaft Cover (See note*)8 83106 1 Shield Hinge Pin9 67716 2 Cap Push Nut10 50017585 1 Shield Mount Weldment

JULY, 2011


67-1-3

1^1&1*1(

1!1@1#1$

1!1@1#1$

1!1@1#1$

1)1!

1)1!1)1!

1)1!

oiu

r

r

t

y

q

y

t

1%

1%

1%

1%

w e

w e

Ref. Part Description Qty.No. No. Req’d.

1 50062095 Shield Cone Assy. 12 50068466 Shield Bottom w/Decal 23 D546 Decal, Danger Shield Missing 24 50068449 Shield Assy. 25 50068454 Shield Mount R.H. 26 50068457 Shield Mount L.H. 27 50035829 Tube, Owners Manual 18 50035830 Seal 19 50035831 Cap 110 ----------- Capscrew, M10 x 1.5 - 20 2011 ----------- Flatwasher 3/8” 2812 ----------- Capscrew, 3/8” x 1” Gr.5 813 ----------- Lockwasher, 3/8” 814 ----------- Hex Nut 3/8” 815 20312 Lynch Pin 416 ----------- Capscrew, 1/4” x 7/8” Gr.5 317 ----------- Flatwasher 1/4” 318 ----------- Lockwasher 1/4” 319 ----------- Hex Nut 1/4” 3

DRIVELINE SHIELDING, NEW STYLE3414 and 13414

July, 2011


67-2-1

23

4

1

6

7

8

95

Right SideCounterclockwise

Left SideClockwise

CenterCounterclockwise 540 RPM (Shown)Clockwise 1000 RPM (Not Shown)

BLADES AND BLADE HOLDERSModel 3414

JULY, 2011


1 63607 6 Blade Bolt Kit2 252 6 Jamnut 1 1/8”3 20322 6 Lockwasher 1 1/8”4 7919 6 Blade Bolt5 86665 2 Blade, Clockwise Rotation (540 RPM)

4 Blade, Clockwise Rotation (1000 RPM)6 86664 4 Blade, Counterclockwise Rotation (540 RPM)

2 Blade, Counterclockwise Rotation (1000 RPM)7 50057117 3 Round Pan Weldment8 50058589 3 Straight Bar Weldment9 50025524 3 Washer (Used with Straight Bar Assembly Only)


67-2-2

REF. PART QTY.NO. NO. 30” SPACING 38”/40” SPACING DESCRIPTION

1 90538 1 1 “V” Baffle2 60032 5 5 Stationary Blade3 84345 5 3 Blade Mount4 84342 5 3 Support Plate5 86666 6 6 Double Edge Blade6 90563 –––– 1 Mount Weldment7 90537 –––– 1 Baffle, Front R.H. (540 RPM)

90536 –––– 1 Baffle, Front L.H. (1000 RPM)8 84667 –––– 1 Support*9 86310 6 6 Pivot Bushing*10 90612 6 6 Blade Bolt*11 44383 6 6 Slotted Nut 1-1/8”*12 15473 6 6 Cotter Pin 1/4” x 2-1/2”13 20294 6 6 Capscrew 5/8” x 6-1/2” Gr.514 9162000 10 10 Locknut 5/8”15 –––– 8 7 Capscrew 1/2” x 1-3/4” Gr.516 –––– 21 14 Flatwasher 1/2”17 –––– 8 7 Lockwasher 1/2”18 –––– 8 8 Hex Nut 1/2”19 –––– –––– 2 Capscrew 5/8” x 2” Gr.520 –––– –––– 2 Capscrew 5/8” x 2-1/2” Gr.521 –––– –––– 10 Lockwasher 5/8”22 50018289 3 3 Blade Holder

*Note: Order 90613 for blade bolt kit. Kit includes parts for 1 blade bar assembly.

SHREDDER ATTACHMENT30” & 38/40” ROW SPACING

For All 3414 Straight Blade Bar Models

3

2

20

20

19

13

5

10

See Blades & Blade Holderspage for these part numbers.

10

99

12

12

1718

1718

14214

7

13

2

3

11

22

11

14 1421

214

1416

8

14214

13

62

23

15

16

16

1

JULY, 2011


67-2-3

LEFT


1 50031969 2 Lighting Assembly (Ref. #1, 15-18)2 50033783 2 Light, Amber3 50033784 2 Light, Red4 50033785 1 Harness, Wishbone5 50033786 1 Harness6 50033787 1 Light Module7 –––– 16 Capscrew 1/4” x 1-1/4”8 44566 16 Hex Nut 1/4” Nylock9 50033788 8 Tie Wrap, Stainless10 50033789 6 J-Clip11 4140606 6 Screw #10 x 3/4”12 44520 6 Locknut #1013 –––– 4 Capscrew 3/4” x 3”14 50031961 2 Light Mount Weldment15 50031964 2 Lighting Weldment16 20325 4 Roll Pin17 46610956 2 Spring18 449 2 Grease Fitting

50033782 LIGHT ASSEMBLYFor Model 3414

1

2

16 7

8

16Existing Locknuts

13

4

1011

12

9 6

5

3

15

14

18

17

JULY, 2002


67-3-1


1 50020277 1 Front Assy., L.H. Single Row50020276 1 Front Assy., R.H. Single Row 2

2 50020272 1 Rear Assy., Center Single Row3 50020274 1 Rear Assy., R.H. Single Row4 50020273 1 Rear Assy., L.H. Single Row5 —— A/R Capscrew 1/2” x 1-1/4” Gr. 56 —— A/R Flatwasher 1/2”7 —— A/R Lockwasher 1/2”8 —— A/R Hex Nut 1/2”9 —— A/R Capscrew 1/2” x 4-1/2” Gr. 510 90205 1 Bracket, Front L.H., Single Row

90206 1 Bracket, Front R.H., Single Row11 50020275 2 Rod, Front12 50020271 1 Rod, Center Rear13 50020278 2 Rod, Rear Side14 90221 1 Bracket, Rear Center, Single Row15 91441 1 Bracket, Rear R.H., Single Row16 91442 1 Bracket, Rear L.H., Single Row17 50017211 A/R Chain, 6 Link, Plated18 –––– A/R Capscrew 5/16” x 2” Gr.519 –––– A/R Flatwasher 5/16”20 –––– A/R Locknut 5/16”21 50017210 A/R Spiral Pin .125” x 1.25”

CHAINSFor 3414 / 13414

21

3

17

13 15

21

10

1

11

17

18 19 19 20

21

14

2

13

21

16

20 19 19 18

21

87

69

21

17

4

1278

56

July, 2011


67-3-2


1 –––– A/R Lockwasher 1/2”2 –––– A/R Flatwasher 1/2”3 –––– A/R Capscrew 1/2” x 4-1/2” Gr.54 –––– A/R Hex Nut 1/2”5 90472 1 Front Belting Assembly6 90325 1 Belting7 90343 2 Cover8 90342 1 R.H. Bracket9 90341 1 L.H. Bracket10 –––– A/R Capscrew 5/16” x 1-1/4” Gr.511 –––– A/R Flatwasher 5/16”12 –––– A/R Lockwasher 5/16”13 –––– A/R Hex Nut 5/16”14 –––– 2 Capscrew 5/16” x 2-1/2” Gr.515 50017212 4 Chain, 7 Link16 9161000 2 Locknut 5/16”17 90291 1 Rear Band18 90293 1 R.H. Rear Band19 90292 1 L.H. Rear Band20 –––– A/R Capscrew 1/2” x 4-1/2” Gr.5

FRONT BELTING & REAR BANDS3414 & 13414

18

8

3 2

1011

1213

7

7

6

5

19

1

2 20

4

9

14, 15, 16

1 4

17

JULY, 2011



1 —— 10 Capscrew 1/2” x 1-1/2” Gr. 52 —— 21 Lockwasher 1/2”3 —— 23 Flatwasher 1/2”4 —— 11 Capscrew 1/2” x 4-1/2” Gr. 55 —— 21 Hex Nut 1/2”6 90576 1 Center Rear Belting Assy.7 —— 27 Capscrew 5/16” x 1-1/4” Gr. 58 —— 27 Hex Nut 5/16”9 —— 27 Lockwasher 5/16”10 —— 54 Flatwasher 5/16”11 90567 1 Rear Center Bracket12 90570 1 Rear Center Belting13 90572 1 Rear Center Cover14 90586 1 R.H. Rear Belting Assy.15 90571 2 Short Rear Belting16 90573 2 Short Rear Cover17 90574 1 R.H. Bracket Weld.18 90587 1 L.H. Rear Belting Assy.19 90575 1 L.H. Bracket Weld.

REAR BELTING BUNDLEFor Models 3414, 13414

With Shredder Attachment

67-3-3

17 15 16

14

1

3

2

5

43

5 2 3

6

11 12 13

8 9 10

10 7

18

1915

16

JULY, 2011


67-4-1


1 50025401 1 Housing2 50025403 2 Cap, Thru3 50025404 1 Cap, Cantilevered4 50025472 1 Inspection Cover5 50025412 1 Gear, 13T (540 RPM Gearbox)

50025415 1 Gear, 18T (1000 RPM Gearbox)6 50025413 1 Gear, Input, 24T (540 RPM Gearbox)

50025415 1 Gear, Input, 18T (1000 RPM Gearbox)7 50025418 1 Shaft, Input 1.75” – 20 Spline8 50025419 1 Shaft, Output, Tapered Spline 18T9 50025420 1 Shaft, Hor. Output 1-3/4” – 20 Spline10 70800 1 Bearing Assembly11 70410 1 Bearing Assembly12 71331 2 Bearing Assembly13 50025423 1 Bearing Assembly14 50025422 1 Bearing Assembly15 50025426 1 Seal, Input16 –––– 1 Seal, Vertical Output (50018607)

50025430 1 Seal, Vertical Output (50018608)17 50025429 2 Seal, Hor. Output18 50025432 A/R Gasket, .1mm19 50025433 A/R Gasket, .2mm20 50025434 A/R Gasket, .5mm21 50025434 A/R Gasket, .1mm22 50025436 A/R Gasket, .2mm23 50025412 1 Gear, 13T (540 RPM Gearbox)

50025414 1 Gear, 22T (1000 RPM Gearbox)


24 50025448 A/R Shim, .10mm25 50025449 A/R Shim, .20mm26 50025450 A/R Shim, .50mm27 50025451 1 Spacer, Output28 50025452 1 Spacer, Output29 44459 1 Cotter Pin30 21020724 2 Cotter Pin31 44281 8 Capscrew M12 x 3532 44340 16 Capscrew M10 x 2533 50025459 2 Hex Nut 1-3/8” – 18 UNF34 50025460 1 Hex Nut M3635 44198 16 Lockwasher M1036 44200 8 Lockwasher M1237 78719 1 Pipe Plug, 1/2” – 14 NPT38 50025464 1 Pipe Plug, 3/8” – 18 NPT39 81572 1 Vent Plug40 88850 1 Retaining Ring41 50025467 1 Retaining Ring 50MM42 50025469 1 Retaining Ring 110MM43 50025471 1 Protection Seal

32 35

17

2 12

4018

1920

39

4

38

1

9

12

172

353237

30

33

27

5

10

8

11

28

42

43

34

29

16

715 41

13

3136

14

33

30

2122

6

3

24, 25, 26

23

3235

50018607 CENTER (INPUT)GEARBOX (540 RPM)Manufactured by OmniUsed on 3414 Models

Replaced by 71266 Gearbox

50018608 CENTER (INPUT)GEARBOX (1000 RPM)Manufactured by OmniUsed on 13414 Models


JULY, 2011


67-4-2


1 50025400 1 Housing2 50025406 1 Cap, Blank3 50025411 1 Gear, Pinion, 18T4 50025407 1 Gear, 21T5 50025416 1 Shaft,Input 1.75” – 20 Spline6 50025417 1 Shaft, Output, 18T7 70800 1 Bearing Assembly8 70796 2 Bearing Assembly9 70410 1 Bearing Assembly10 50068116 1 Seal, Input11 50025430 1 Seal, Output12 50025438 A/R Gasket, .2MM13 50025439 A/R Gasket, .3MM14 50025440 A/R Gasket, .5MM15 50025441 A/R Shim, Input, 1.8MM16 50025442 A/R Shim, Input, 2MM17 50025443 A/R Shim, Input, 2.2MM18 50025444 A/R Shim, Input, 2.5MM19 50025445 A/R Shim, Input, .10MM20 50025446 A/R Shim, Input, .20MM21 50025447 A/R Shim, Input, .50MM22 50025448 A/R Shim, Output, .10MM23 50025449 A/R Shim, Output, .20MM24 50025450 A/R Shim, Output, .50MM25 50025452 1 Spacer, Output26 44459 1 Cotter Pin27 21020724 1 Cotter Pin28 44299 8 Capscrew M8 – 1.25 x 2529 44202 4 Capscrew M10 – 1.5 x 3030 50025459 1 Hex Nut 1-3/8” – 18 UNF31 50025460 1 Hex Nut M36


32 44311 8 Lockwasher M833 44198 4 Lockwasher M1034 78719 1 Pipe Plug 1/2”35 50025464 1 Pipe Plug 3/8” – 18 NPT36 81572 1 Vent Plug37 88850 1 Retaining Ring, External38 50025468 1 Retaining Ring, External39 50025469 1 Retaining Ring, Internal40 50025470 1 Inspection Cover41 50025471 1 Protective Seal

50018599 OUTBOARD GEARBOX(1000 RPM)

Manufactured by OmniUsed on 13414 Models


29

2 1213 14

15, 16,17, 18

8

3328

32 40

374

8192021

38

10

5

35

1

34

6

97

3

3027

222324

25

11

39

41

31

26

36

July, 2011


67-4-3


1 50025400 1 Housing2 50025406 1 Cap, Blank3 50025407 2 Gear, 21T4 50025471 1 Protective Seal5 50025416 1 Shaft,Input 1.75” – 20 Spline6 50025417 1 Shaft, Output, 18T7 70800 1 Bearing Assembly8 70796 2 Bearing Assembly9 70410 1 Bearing Assembly10 50068116 1 Seal, Input11 50025430 1 Seal, Output12 50025438 A/R Gasket, .2MM13 50025439 A/R Gasket, .3MM14 50025440 A/R Gasket, .5MM15 50025441 A/R Shim, Input, 1.8MM16 50025442 A/R Shim, Input, 2MM17 50025443 A/R Shim, Input, 2.2MM18 50025444 A/R Shim, Input, 2.5MM19 50025445 A/R Shim, Input, .10MM20 50025446 A/R Shim, Input, .20MM21 50025447 A/R Shim, Input, .50MM22 50025448 A/R Shim, Output, .10MM23 50025449 A/R Shim, Output, .20MM24 50025450 A/R Shim, Output, .50MM25 50025452 1 Spacer, Output26 44459 1 Cotter Pin27 21020724 1 Cotter Pin28 44299 8 Capscrew M8 – 1.25 x 2529 44202 4 Capscrew M10 – 1.5 x 3030 50025459 1 Hex Nut 1-3/8” – 18 UNF31 50025460 1 Hex Nut M3632 44311 8 Lockwasher M8


33 44198 4 Lockwasher M1034 78719 1 Pipe Plug 1/2”35 50025464 1 Pipe Plug 3/8” – 18 NPT36 81572 1 Vent Plug37 88850 1 Retaining Ring, External38 50025468 1 Retaining Ring, External39 50025469 1 Retaining Ring, Internal40 50025470 1 Inspection Cover


Manufactured by OmniUsed on Model 3414


29

2 1213 14

15, 16,17, 18

8

33 28

32 40

373

8192021

38

10

5

35

1

34

6

97

3

3027

222324

25

11

39

4

31

26

36

July, 2011


67-4-4


1 76867 1 Output Shaft2 50068116 2 Oil Seal3 44202 26 Capscrew M10 x 1.5 x 304 76868 2 Cover5 71331 2 Bearing 302096 70348 2 Shim 0.37 76879 1 Gear (71266 Gearbox)

76869 1 Gear, 22T (71267 Gearbox)8 76870 1 Spacer9 70419 1 Cotter Pin10 70752 2 Shim 0.311 70344 2 Shim 0.312 70800 1 Bearing 3021013 76871 1 Casing14 70410 1 Bearing 3021215 50062245 1 Oil Seal16 76661 1 Protective Washer17 76872 1 Output Shaft18 71492 2 Cotter Pin19 70586 2 Castle Nut20 76913 1 Oil Level Plug21 50025422 1 Bearing 3231022 76873 1 Cover*23 71523 1 Input Shaft

50047693 1 Input Shaft Kit (Shaft, Spacer,Cotter Pin)

24 76875 1 Oil Seal


25 50025423 1 Bearing 3221026 76881 1 Gear (71266 Gearbox)

76876 1 Gear, 18T (71267 Gearbox)27 70349 2 Shim 0.428 70350 2 Shim 0.529 70351 2 Shim 1.030 70753 2 Shim 0.431 70754 2 Shim 0.532 70755 2 Shim 1.033 70345 2 Shim 0.534 70346 2 Shim 1.035 70347 2 Shim 0.436 76664 1 Blank Washer37 70418 1 Castle Nut38 76879 1 Gear (71266 Gearbox)

76876 1 Gear, 18T (71267 Gearbox)39 71524 1 Spacer

71266 CENTER (INPUT)GEARBOX (540 RPM)Manufactured by ComerUsed on 3414 Models

Replaces 50018607 Omni Gearbox

71267 CENTER (INPUT)GEARBOX (1000 RPM)Manufactured by ComerUsed on 13414 Models

Replaces 50018608 Omni Gearbox

2 3

5

7

8

18

1918

19

17

14

15

16

36379

38

12

11, 3334, 35

26

21

23*

39

3

222524

11, 3334, 35

20

13

1

43

2

5

6, 2728, 29

10, 3031, 32

10, 3031, 32

6, 2728, 29

4

13.09”

*Note, Ref. 23: Some gearboxes have input shafts that areshorter than the replacement shaft. Before ordering a replace-ment input shaft, measure the length of the shaft. If the shaftis 13.00” long, order #71523 Shaft only. If the shaft is not13.00” long, order #50047693 Input Shaft Kit (includes inputshaft, spacer and cotter pin).

JULY, 2011


67-4-5


22 70740 1 Spacer23 70722 1 Snap Ring24 76634 1 Shim, 1mm25 70753 1 Shim, .4mm26 70754 1 Shim, .5mm27 70755 1 Shim, 1mm28 70345 1 Shim, .5mm29 70346 1 Shim, 1mm30 70347 1 Shim, .4mm31 76664 1 Blank Washer32 70418 1 Castle Nut M3633 70419 1 Cotter Pin

70998 GEARBOX ASSEMBLY1000 RPM, Ratio 1:1.22Used on 13414 Models

Manufactured by Comer / EGReplaces 50018599 Omni Gearbox

206

73

11

19

9

24 17

16

15

14

32

31

30292810

2

13

33

5

12

18

8

1

23 21

223

64

7252627


1 76658 1 Casting2 76667 1 Gear, Ouput, 18 Teeth3 70796 2 Bearing4 50068116 1 Oil Seal5 76659 1 Input Shaft 1-3/4”6 70189 2 Snap Ring7 70752 2 Shim .3mm8 76660 1 Top Plate9 70586 1 Castle Nut10 70344 1 Shim .3mm11 70292 1 Oil Filler Plug 1/2” Gas12 44595 4 Capscrew M10 x 14 Gr.8.813 70800 1 Bearing14 76661 1 Protective Washer15 50062245 1 Oil Seal16 70410 1 Bearing17 76663 1 Shaft, Output18 80538 1 Vent Plug19 70585 1 Cotter Pin20 70725 1 Cap21 76668 1 Gear, Input, 22 Teeth

JULY, 2011


67-4-6


1 76658 1 Casting2 70960 2 Gear 21T3 70796 2 Bearing 302094 50068116 1 Oil Seal5 76659 1 Input Shaft6 70189 2 Snap Ring7 70752 2 Shim 0.38 76660 1 Top Plate9 70586 1 Castle Nut M4010 70344 1 Shim 0.311 70292 1 Oil Filler Plug 1/2” Gas12 44595 4 Capscrew M10 x 1.5 x 1413 70800 1 Bearing 3021014 76661 1 Protective Washer15 50062245 1 Oil Seal16 70410 1 Bearing 3021217 76663 1 Output Shaft18 80538 1 1/2” Gas Plug19 70585 1 Cotter Pin20 70725 1 Cap21 70740 1 Spacer22 70722 1 Snap Ring23 76634 1 Shim 1.024 70753 2 Shim .425 70754 2 Shim .526 70755 2 Shim 1.027 70345 1 Shim .528 70346 1 Shim 1.029 70347 1 Shim .430 76664 1 Blank Washer31 70418 1 Castle Nut32 70419 1 Cotter Pin


Manufactured by ComerUsed on 3414 Models

Replaces Omni Gearbox 50018596

20

7,2425, 26

6

12

18

8

3 22

1

19

23

9

5

11

212

37

64

2

13

32 31

30

14

15

16

17

10, 2728, 29

Note: Omni gearbox has 6 holes in top plate.Comer gearbox has 4 holes in top plate.

JULY, 2011



1 90352 1 Mount Weld.2 88100 1 Shield Weld.3 90356 1 Pin Weld.4 –––– 2 Capscrew 1/2” x 1 1/4” Gr.55 –––– 1 Lockwasher 3/4”6 9162400 1 Locknut 3/4”7 –––– 2 Lockwasher 1/2”8 20763 2 Capscrew 5/8” x 5” Gr.59 20237 2 Capscrew 5/8” x 4” Gr.510 19486 4 Lockwasher 5/8”11 9162000 4 Locknut 5/8”12 90986 1 Pillow Block Bearing13 88916 2 Bushing, Tension14 77492 1 Snap Ring15 77491 1 Bearing w/ Collar16 88840 1 Set Screw17 90983 1 Spacer

67-5-1

PILLOW BLOCK BEARING & MOUNT3414 & 13414 Pull Models

4

7

2

1713

1315

1614

12

3 1

5

6

8

9

10 11

10

11

JULY, 2011


67-5-2


1 76248 1 Push Pin Yoke (76405)76494 1 Push Pin Yoke (76412)

2 64963 2 Cross Journal Set3 63956 2 Grease Nipple4 76479 1 Yoke w/ Sleeve Assy. (76405, 76412)

76486 1 Yoke w/ Sleeve Assy. (76406)5 76335 1 Grease Nipple6 76480 1 Splined Shaft7 66866 1 Roll Pin for Inner Tube8 68172 1 Inner Yoke9 76481 1 Push Pin Yoke (76405, 76412)

76481 2 Push Pin Yoke (76406)10 76244 1 Guard Retaining Collar, Outer11 87992 6 Bolt12 76245 1 Guard Retaining Collar, Inner13 64814 2 Safety Chain14 76482 1 Complete Shield w/ Instr. (76405)

76487 1 Complete Shield w/ Instr. (76406)15 76062 2 Push Pin Set, 1-3/8” (76405, 76412)16 76483 2 Push Pin Set, 1-3/4” (76405, 76412)

76483 4 Push Pin Set, 1-3/4” (76406)17 76484 1 Half Female Shaft w/ Shield (76405)

76488 1 Half Female Shaft w/ Shield (76406)76501 1 Half Female Shaft w/ Shield (76412)

18 76485 1 Half Male Shaft w/ Shield (76405, 76412)76489 1 Half Male Shaft w/ Shield (76406)

19 78786 1 Danger Decal, Outer Tube20 78608 1 Danger Decal, Outer Shield

76405 DRIVESHAFT540 RPM – 1-3/8” – 6 Spline

Mfd. by Comer/EGUsed on 3414 Pull Models

May substitute 84722 Driveshaft







15

19

5

10 1111

13

1220

2 9

16876

1

3

24

3

17 18

14

July, 2011


67-5-3


1 76803 1 Complete Collar Yoke (76729)76805 1 Complete Collar Yoke (76730)76806 1 Complete Collar Yoke (76731)

2 64963 2 Cross Journal Set3 63956 2 Grease Nipple4 78134 1 Outer Yoke5 67108 1 Roll Pin for Outer Tube6 78133 1 Outer Tube (76729, 76730)

86607 1 Outer Tube (76731)7 78132 1 Inner Tube (76729, 76730)

86608 1 Inner Tube (76731)8 67085 1 Roll Pin for Inner Tube9 67086 1 Inner Yoke10 76490 1 Complete Disc Clutch11 76244 1 Guard Retaining Collar, Outer12 87992 6 Bolt13 76245 1 Guard Retaining Collar, Inner14 64814 2 Safety Chain15 76491 1 Complete Shield w/ Instr.

(76729, 76730)76496 1 Complete Shield w/ Instr. (76731)


16 50017480 1 Ball Collar Kit 1-3/8” (76729, 76730)50017502 1 Ball Collar Kit 1-3/4” (76731)

17 76080 8 Spring18 76331 1 Flanged Yoke19 76082 1 Bushing20 76083 4 Lining Ring21 76247 1 Tapered Pin Set 1-3/4”22 76458 1 Clutch Support23 76085 2 Inner Plate24 76197 1 Intermediate Plate25 76086 1 Pressure Plate26 44159 8 Capscrew M10 x 1.5 x 10027 44154 8 Lock Nut M10 x 1.528 76815 1 Half Female Shaft w/ Shield (76729)

76816 1 Half Female Shaft w/ Shield (76730)76836 1 Half Female Shaft w/ Shield (76731)

29 76493 1 Half Male Shaft w/ Shield(76729, 76730)

76498 1 Half Male Shaft w/ Shield (76731)30 78786 1 Danger Decal, Outer Tube31 78608 1 Danger Decal, Outer Shield

76729 DRIVESHAFT(Mfd. by Comer/EG)

540 RPM – 1-3/8” – 6 SplineUsed on 3414 Lift & Semi-Mount Models

Replaces 76407 DriveshaftMay substitute 86580 Driveshaft







2717 18

1920 21

2022

24 5

1131

14

1212

6 730

23 20 24 20 23 25 26

29

13

8 31

3

15

29

28

10

16

Note: Some early driveshafts were shipped with push pins on the tractor yoke end. Order 76062 push pin set to replace pin.Order (Ref. #1) Complete Collar Yoke for complete yoke replacement.

July, 2011


67-5-4


1 76239 1 Complete Yoke2 64963 2 Cross Journal Set3 –––– 8 Circlip4 63956 2 Grease Nipple5 76703 1 Inner Tube6 67085 1 Roll Pin for Inner Tube7 67086 1 Inner Yoke8 76704 1 Complete Rubber Element9 –––– 1 Yoke10 76247 2 Tapered Pin Set 1-3/4”11 –––– 1 Female Tube Yoke12 –––– 1 Male Tube Yoke13 76705 1 Half Female Shaft14 76706 1 Half Male Shaft15 78786 1 Danger Decal

76569 CROSS SHAFTManufactured by Comer/EG

Used on Model 3414This driveshaft is obsolete. For replacement of complete driveshaft,

order 50035303 Cross Shaft and 50035717 Shield Kit.

10 9

1

155

67 3

4

10

211

2 8

43

13

12

14

JULY, 2002


67-5-5


1 50017482 1 Complete Collar Yoke (76624)50017501 1 Complete Collar Yoke (50024435)

2 76420 2 Cross Journal Set3 76579 3 Grease Nipple4 76421 1 Wide Angle Double Yoke5 76893 1 Outer Yoke6 66866 1 Roll Pin for Outer Tube7 76894 1 Wiper8 76901 1 Outer Tube w/ Decal (76624)

76900 1 Outer Tube w/ Decal (50024435)9 64663 1 Cross Journal Set10 76422 1 Complete Yoke11 76362 6 Screw Kit12 76423 1 Bearing Ring13 76057 1 Collar, Outer Tube14 87992 6 Bolt15 76059 1 Collar, Inner Tube


16 64814 3 Safety Chain17 76933 1 Guard Cone Set18 76948 1 Complete Shield (76624)

76957 1 Complete Shield (50024435)19 76247 1 Tapered Pin Set 1-3/4”20 76681 1 Female Tube w/ Yoke & Lube21 76682 1 Male Tube w/ Yoke & Lube22 76949 1 Half Female Shaft

w/ Shield (76624)76958 1 Half Female Shaft

w/ Shield (50024435)23 76684 1 Half Male Shaft w/ Shield24 78786 1 Danger Decal, Outer Tube25 78608 1 Danger Decal, Outer Shield26 76892 1 Plastic Cap, Outer Tube27 50017480 1 Ball Collar Kit 1-3/8” (76624)

50017502 1 Ball Collar Kit 1-3/4” (50024435)

76624 C.V. DRIVESHAFT ASSEMBLY1000 RPM – 1-3/8” – 21 SplineManufactured by Comer / EG

ASAE Size 4Used on 3414 Pull ModelsReplaces 76233 Driveshaft

50024435 C.V. DRIVESHAFT ASSEMBLY1000 RPM – 1-3/4” – 20 SplineManufactured by Comer / EG

ASAE Size 4Used on 3414 Pull ModelsReplaces 76571 Driveshaft

27

1

24 8

266

10

20 21

193

2

3

9

3

11 17

13

14 14

15

16

2512

18

22 23

245 7

July, 2011


67-5-6


1 50017504 1 Complete Collar Yoke2 76356 2 Cross Journal Set3 76579 3 Grease Nipple4 76357 1 Wide Angle Double Yoke5 76604 1 Cross Journal Set6 76239 1 Complete Yoke7 76362 6 Screw Kit8 76363 1 Bearing Ring9 76244 1 Collar, Outer Tube10 87992 6 Bolt11 76245 1 Collar, Inner Tube


12 64814 3 Safety Chain13 76950 1 Guard Cone Set14 76951 1 Complete Guard15 76247 1 Tapered Pin Set 1-3/4”16 76687 1 Female Tube w/ Yoke & Lube17 76688 1 Male Tube w/ Yoke & Lube18 76952 1 Half Female Shaft w/ Guarding19 76690 1 Half Male Shaft w/ Guarding20 78786 1 Danger Decal21 78608 1 Danger Decal22 50017480 1 Ball Collar Kit, 1-3/8”

76625 C.V. DRIVESHAFT ASSEMBLY540 RPM – 1-3/8” – 6 SplineManufactured by Comer/EGUsed on 3414 Pull Models

22

1

4

20

6

16 17

15

2

3

2

3

5

3

7

13

9

10 10

11

12

218

14

18 19

July, 2011


67-5-7

76627 JACKSHAFT ASSEMBLYManufactured by Comer/EGUsed on 3414 Pull Models


1 76490 1 Complete Disc Clutch2 64963 1 Cross Journal Set3 63956 1 Grease Nipple4 78134 1 Outer Yoke5 67108 1 Roll Pin for Outer Tube6 76693 1 Outer Tube w/ Splined Shaft7 76244 1 Guard Retaining Collar8 87992 6 Bolt9 76245 1 Guard Retaining Collar10 64814 2 Safety Chain11 76694 1 Complete Shield12 44159 8 Bolt M10 x 100


13 78086 1 Pressure Plate14 76085 2 Inner Plate15 76083 4 Lining Ring16 76197 1 Intermediate Plate17 76458 1 Clutch Support18 76247 1 Tapered Pin Set 1-3/4”19 76082 1 Bushing20 76331 1 Flanged Yoke21 76080 8 Spring22 78786 1 Danger Decal, Outer Tube23 78608 1 Danger Decal, Outer Shield Tube24 44342 8 Hex Nut M10

12 13 14 1415 16 15 15 15 1920 21 2418 17

3

2

4 65

22

7

810

23 9

11

1

July, 2011


67-5-8


1 50024795 1 Yoke 1-3/8” – 20 Spline2 595 2 Cross and Bearing Kit3 96494 1 Yoke & Bar Assembly4 96495 1 Sleeve, Yoke & Tube Assembly5 50024796 1 Shearbolt Clutch6 44864 1 Capscrew 1/2” x 2-3/4” Gr.8 Blk. Oxide7 15508 1 Hex Nut 1/2”8 78786 1 Safety Decal9 –––– 1 Capscrew 5/8” – 11 UNC x 3-1/4” Gr.810 –––– 1 Lockwasher 5/8”11 –––– 1 Hex Nut 5/8”12 –––– 2 Capscrew M16 x 2 x 8013 –––– 2 Hex Nut M16

50018594 CROSS SHAFT WITH SHEARBOLT CLUTCH1000 RPM – 1-3/4” – 20 SplineManufactured by Walterscheid

Used on Model 13414

1110

12

3

48

2 5

12

13

9

7 6

JULY, 2011


67-5-9

11

1

9 56

8 3

4

11

27

2

10

43

12 13


1 85414 1 Complete Yoke2 68176 2 Cross Journal Set3 –––– 8 Circlip4 63946 2 Grease Nipple5 50035693 1 Inner Tube6 67085 1 Roll Pin for Inner Tube7 50035694 1 Female Yoke & Tube8 67086 1 Inner Tube Yoke9 78786 1 Danger Decal10 50035695 1 Joint11 50053705 2 Pivot12 50035696 1 Half Female Shaft13 50035697 1 Half Male Shaft

50035303 CROSS SHAFTBondioli & Pavesi Series 8, ASAE Size 5

Used on 3414 & 13414Replaces 76569 Cross Shaft (Comer / EG)

JULY, 2011


76841 CV DRIVESHAFT ASSEMBLY540 RPM, 1-3/8” - 6 SPLINE TRACTOR YOKE

ASAE SIZE 5MANUFACTURED BY BONDIOLI & PAVESI

Used On: 540 RPM Pull Models 3414


1 71390 1 Yoke, CV 1-3/8” -6 Spline (Tractor)2 71391 2 Cross Bearing Kit3 63946 4 Grease Fitting4 71392 1 Yoke w/Hub, Outer Tube5 71393 1 Central Body6 71428 1 Outer Cardan Tube7 71429 1 Inner Tube Assy. w/Lube Fitting8 71396 1 Flexible Pin9 71397 1 Flexible Pin10 71398 1 Yoke, Inner Tube11 71399 1 Cross Bearing Kit12 71400 1 Tube Plug13 71401 1 Yoke, 1-3/4”-20 Spline (Implement)14 71440 1 Grease Fitting


15 71455 1 Outer Ring16 71402 1 Ring for Inner Cone17 71403 1 Ring18 71404 17 Screw19 71405 1 Chain20 71447 1 Shield Tube Connecting Ring21 78608 1 Danger Decal22 78786 1 Danger Shield Missing23 71406 1 Sleeve Kit24 71407 1 Pivot25 71430 1 Outer Half Shaft26 71431 1 Inner Half Shaft27 71432 1 Complete Guard Assembly

67-5-10

July, 2011


76842 CV DRIVESHAFT ASSEMBLY1000 RPM, 1-3/8”- 21 SPLINE TRACTOR YOKE




1 71441 1 Yoke, CV 1-3/8” -21 Spline (Tractor)2 71412 2 Cross Bearing Kit3 63946 4 Grease Fitting4 71413 1 Yoke w/Hub, Outer Tube5 71414 1 Central Body6 71442 1 Outer Cardan Tube7 71443 1 Inner Tube Assy. w/Lube Fitting8 66866 1 Flexible Pin9 71418 1 Flexible Pin10 71419 1 Yoke, Inner Tube11 71420 1 Cross Bearing Kit12 71421 1 Tube Plug13 71422 1 Yoke, 1-3/4”-20 Spline (Implement)14 71440 1 Grease Fitting



67-5-11

JULY, 2011


76843 CV DRIVESHAFT ASSEMBLY1000 RPM, 1-3/4”- 20 SPLINE TRACTOR YOKE




1 71411 1 Yoke, CV 1-3/4” - 20 Spline (Tractor)2 71412 2 Cross Bearing Kit3 63946 4 Grease Fitting4 71413 1 Yoke w/Hub, Outer Tube5 71414 1 Central Body6 71415 1 Outer Cardan Tube7 71416 1 Inner Tube Assy. w/Lube Fitting8 66866 1 Flexible Pin9 71418 1 Flexible Pin10 71419 1 Yoke, Inner Tube11 71420 1 Cross Bearing Kit12 71421 1 Tube Plug13 71422 1 Yoke, 1-3/4”-20 Spline (Implement)14 71440 1 Grease Fitting



67-5-12

JULY, 2011


67-6-1


1 20150 2 Capscrew 1” x 8-1/2” Gr.52 9163200 2 Locknut 1”3 94117 2 Bushing 5-21/32” Long4 20325 6 Roll Pin 1/4” x 1-3/4”5 88983 1 Pin6 90591 1 Leveling Rod Assembly7 15612 1 Jam Nut 1”8 15908 2 Flatwasher 1”9 53053 1 Turnbuckle10 –––– 4 Cotter Pin 3/16” x 1-1/2”11 90588 1 End Weldment12 90592 1 Rod Weldment13 90599 2 Pin

92882 1 Tongue Assembly14 87317 1 Important Decal15 87340 1 Important Decal16 92883 1 Tongue Weldment17 92890 1 Clevis Weldment18 85653 2 Pin19 92889 1 Bushing20 24D25128 1 Jackstand Assembly21 91074 1 Safety Tow Chain

4 5

4

10

1311

10

97

12

10

10

138

8

15

16

17

4

4

1819

14

1

3

2

6

PULL TYPE HITCHFor 3414 & 13414 Pull Models

20

21

JULY, 2011



1 –––– 1 Lockwasher 3/4”2 15821 3 Lockwasher 1”3 15908 2 Flatwasher 1”4 19061 1 Capscrew 1” x5” Gr. 55 19502 3 Hex Nut 1”6 –––– 1 Hex Nut 3/4”7 20232 2 Capscrew 1” x 2 1/2” Gr.58 –––– 1 Capscrew 3/4” x 4 1/2” Gr.59 20558 2 Lynch Pin10 44250 2 Capscrew 1” x 10 1/2” Gr.511 69528 2 Mast Link Bushing12 9163200 2 Locknut 1”13 25G12545 2 Hitch Pin14 90213 1 Mast Bushing15 90212 1 Top Mast Bushing16 90105 1 Slide Tube Weld.17 90194 1 Mast Link Weldment18 50018220 1 Mast Weldment19 20325 2 Roll Pin 1/4” x 1 3/4”20 88983 1 Pin

3 POINT LIFT HITCH AND SEMI-MOUNT HITCHFor 3414 Lift Models

67-6-2

123

14

52

61

8

16

15

10

1125

1919

20

7

9

13

18

17

4

JULY, 2011


67-7-1


1 50076 1 Bearing Cone2 7968 1 Seal, 2” Dia.3 7967 1 Seal, 1.75” Dia.4 14-6-241 1 Bearing Cone5 50024528 1 Axle Arm Weldment6 1613 1 Hub Assembly (7–10, 31, 32)7 449 1 Grease Fitting8 1612 1 Hub9 14-6-197 1 Bearing Cup10 14-6-242 1 Bearing Cup11 50025514 1 Spindle, Single12 50025513 1 Spacer13 50025512 1 Spacer14 18141206 2 Setscrew 3/8” x 3/4” G815 15554 1 Locknut 1/2”16 20864 1 Capscrew 1/2” x 3”


17 15521 1 Locknut, Collar, 1-1/4”18 –––– 1 Flatwasher 1-1/4”19 –––– 4 Lockwasher 3/4”20 50035301 1 Spring21 15598 1 Locknut 5/8”22 15612 1 Jam Nut 1”23 19502 1 Hex Nut 1”24 –––– 4 Hex Nut 3/4”25 –––– 4 Capscrew 3/4” x 2-1/4” G826 20294 1 Capscrew 5/8” x 6-1/2” G527 20860 1 Capscrew 1” x 7-1/2” G528 68643 1 Axle Clamp29 50024527 1 Stop Clamp30 50024526 1 Axle Mount Weldment31 15445 1 Lug Bolt 1/2” x 1-5/8”32 15515 1 Lug Nut 1/2”

SINGLE AXLE ARM ASSEMBLY (SPRING MOUNT)For 3414 Pull Models

12

13

31

3214

20

21

26

30

23

22

16

1115

5

27

25

28

18

29

17

1924

14

31

6

42

10

9

87

JULY, 2011


67-7-2


1 20166 2 Cotter Pin 1/8” x 1-1/4”2 –––– 2 Flatwasher 3/4”3 120 2 Slotted Nut 3/4”4 50076 2 Bearing Cone5 50073 2 Bearing Cone6 121 2 Hub Cap7 7977 2 Hub Assembly (8–13)8 14-6-198 1 Bearing Cup9 14-6-197 1 Bearing Cup10 15445 5 Lug Bolt 1/2” x 1-5/8”11 15515 5 Lug Nut 1/2”12 7965 1 Hub13 449 1 Grease Fitting14 7967 2 Seal, 1.75” O.D.15 –––– 2 Capscrew 1/2” x 3”


16 15554 2 Locknut 1/2”17 50024528 1 Axle Arm Weldment18 50026089 1 Dual Spindle19 50024526 1 Axle Mount Weldment20 –––– 4 Lockwasher 3/4”21 50035301 1 Spring22 15598 1 Locknut 5/8”23 15612 1 Jam Nut 1”24 19502 1 Hex Nut 1”25 –––– 4 Hex Nut 3/4”26 –––– 4 Capscrew 3/4” x 2-1/4” G827 20294 1 Capscrew 5/8” x 6-1/2” G528 20860 1 Capscrew 1” x 7-1/2” G529 68643 1 Axle Clamp30 50024527 1 Stop Clamp

DUAL AXLE ARM ASSEMBLY (SPRING MOUNT)For 3414 Pull Models

21

22

1827

19

24

23

15

16

28

26

29

30

17

20

25

11

1014

4

1

7

52

36

8

9

1213

JULY, 2011


67-7-3

14

15

11

1216

22

22

17

28

32

25

24

18

1317

5

29

27

30

20

31

23

23

19

2126

16

31

6

42

10

9

87


1 50076 1 Bearing Cone2 7968 1 Seal, 2” Dia.3 7967 1 Seal, 1.75” Dia.4 14-6-241 1 Bearing Cone5 50050188 1 Axle Arm Weldment6 1613 1 Hub Assembly (7–12)7 449 1 Grease Fitting8 1612 1 Hub9 14-6-197 1 Bearing Cup10 14-6-242 1 Bearing Cup11 15445 1 Lug Bolt 1/2” x 1-5/8”12 15515 1 Lug Nut 1/2”13 50025514 1 Spindle, Single14 50025513 1 Spacer15 50025512 1 Spacer16 18141206 2 Setscrew 3/8” x 3/4” G817 15554 1 Locknut 1/2”


18 20864 1 Capscrew 1/2” x 3”19 15521 1 Locknut, Collar, 1-1/4”20 –––– 1 Flatwasher 1-1/4”21 –––– 4 Lockwasher 3/4”22 67495 2 Sandwich Mount23 –––– 2 Hex Nut 1/2”24 15612 1 Jam Nut 1”25 19502 1 Hex Nut 1”26 –––– 4 Hex Nut 3/4”27 –––– 4 Capscrew 3/4” x 2-1/4” G828 20294 1 Capscrew 1/2” x 5-3/4” G529 20151 1 Capscrew 1” x 9” G530 68643 1 Axle Clamp31 77660 1 Stop Clamp32 50050187 1 Axle Mount Weldment

SINGLE AXLE ARM ASSEMBLY (RUBBER MOUNT)For 3414 Pull Models

JULY, 2011


67-7-4


1 20166 2 Cotter Pin 1/8” x 1-1/4”2 –––– 2 Flatwasher 3/4”3 120 2 Slotted Nut 3/4”4 50076 2 Bearing Cone5 50073 2 Bearing Cone6 121 2 Hub Cap7 7977 2 Hub Assembly (8–13)8 14-6-198 1 Bearing Cup9 14-6-197 1 Bearing Cup10 15445 5 Lug Bolt 1/2” x 1-5/8”11 15515 5 Lug Nut 1/2”12 7965 1 Hub13 449 1 Grease Fitting14 7967 2 Seal, 1.75” O.D.15 –––– 2 Capscrew 1/2” x 3”16 15554 1 Locknut 1/2”


17 50050188 1 Axle Arm Weldment18 50026089 1 Dual Spindle19 50050187 1 Axle Mount Weldment20 –––– 4 Lockwasher 3/4”21 67495 2 Sandwich Mount22 15598 2 Hex Nut 1/2”23 15612 1 Jam Nut 1”24 19502 1 Hex Nut 1”25 –––– 4 Hex Nut 3/4”26 –––– 4 Capscrew 3/4” x 2-1/4” G827 20294 1 Capscrew 1/2” x 5-3/4” G528 20151 1 Capscrew 1” x 9” G529 68643 1 Axle Clamp30 77660 1 Stop Clamp31 –––– 2 Hex Nut 1/2”

DUAL AXLE ARM ASSEMBLY (RUBBER MOUNT)For 3414 Pull Models

21

16

18

27

19

24

23

21

15

16

28

26

29

30

31

31

17

2025

11

10144

1

7

523

6

8

9

1213

JULY, 2011


67-7-5


1 18141206 2 Setscrew 3/8” x 3/4” Gr.82 7967 1 Seal, 1.75 O.D.3 15521 1 Locknut, 1-1/4”4 7968 1 Seal, 2.0” O.D.5 1596 1 Spacer, Small6 1595 1 Spacer, Large7 50076 1 Bearing Cone8 14-6-241 1 Bearing Cone9 294 1 Wheel Assembly (10–14)10 116 1 Solid Tire11 117 2 Wheel Flange12 15597 5 Nut 3/8” UNF13 –––– 5 Lockwasher 3/8”14 20126 5 Bolt 3/8” x 1” UNF15 1613 1 Hub Assembly (17–21)16 449 1 Grease Fitting17 1612 1 Hub18 14-6-197 1 Bearing Cup19 14-6-242 1 Bearing Cup20 15445 5 Lug Bolt21 15515 5 Lug Nut


22 1620 1 Spindle23 81464 1 Caster Weldment24 50025542 1 Caster Arm Weldment25 52732 1 Spirol Pin 1/2” x 3”26 81467 1 Spacer27 50024526 1 Axle Mount Weldment28 –––– 4 Lockwasher 3/4”29 6387 1 Spring30 15598 1 Locknut 5/8”31 15612 1 Jam Nut 1”32 19502 1 Hex Nut 1”33 –––– 4 Hex Nut 3/4”34 –––– 4 Capscrew 3/4” x 2-1/4” G835 20294 1 Capscrew 5/8” x 6-1/2” G536 20860 1 Capscrew 1” x 7-1/2” G537 68643 1 Axle Clamp38 50024527 1 Stop Clamp

SINGLE TAILWHEEL ASSEMBLY(SPRING MOUNT)

For 3414 Lift & Semi-Mount Models

36

3025 26

9

29

24

38

3

22

23

5

8

4 6

1

27

15

121

20

27

34

37

3328

3231

35

18

1617 19

1213 11

11

14

10

JULY, 2011


67-7-6


1 18141206 2 Setscrew 3/8” x 3/4” Gr.82 7967 1 Seal, 1.75 O.D.3 15521 1 Locknut, 1-1/4”4 7968 1 Seal, 2.0” O.D.5 1596 1 Spacer, Small6 1595 1 Spacer, Large7 50076 1 Bearing Cone8 14-6-241 1 Bearing Cone9 294 1 Wheel Assembly (10–14)10 116 1 Solid Tire11 117 2 Wheel Flange12 15597 5 Nut 3/8” UNF13 –––– 5 Lockwasher 3/8”14 20126 5 Bolt 3/8” x 1” UNF15 1613 1 Hub Assembly (17–21)16 449 1 Grease Fitting17 1612 1 Hub18 14-6-197 1 Bearing Cup19 14-6-242 1 Bearing Cup20 15445 5 Lug Bolt21 15515 5 Lug Nut


22 1620 1 Spindle23 81464 1 Caster Weldment24 50050189 1 Caster Arm Weldment25 52732 1 Spirol Pin 1/2” x 3”26 81467 1 Spacer27 50050187 1 Axle Mount Weldment28 –––– 4 Lockwasher 3/4”29 67495 2 Sandwich Mount30 15554 1 Locknut 1/2”31 15612 1 Jam Nut 1”32 19502 1 Hex Nut 1”33 –––– 4 Hex Nut 3/4”34 –––– 4 Capscrew 3/4” x 2-1/4” G835 –––– 1 Capscrew 1/2” x 5-3/4” G536 20860 1 Capscrew 1” x 9” G537 68643 1 Axle Clamp38 77660 1 Axle Stop39 –––– 2 Hex Nut 1/2”

SINGLE TAILWHEEL ASSEMBLY(RUBBER MOUNT)

For 3414 Lift & Semi-Mount Models

36

30

39

39

2526

9

29

2924

38

3

22

23

5

84

6

1

27

15

121

20

27

34

37

3328

3132

35

18

1617 19

1213 11

11

14

10

JULY, 2011



1 116 1 Solid Tire2 117 2 Wheel Flange3 15597 5 Nut 3/8” UNF4 –––– 5 Lockwasher 3/8”5 20126 5 Bolt 3/8” x 1” UNF

294 SOLID TIRE ASSEMBLY

12

2

3 4

5


1 97709 1 Tire 24 x 7.7 x 10 14/16 Ply2 92860 1 Tube 5.5 x 103 92861 1 Wheel Flange w/ Hole for Tube Valve4 92862 1 Wheel Flange wo/Hole for Tube Valve5 92863 1 Inner Wheel Lining6 –––– 10 Capscrew 1/2” x 1” Gr.57 –––– 10 Lockwasher 1/2”8 –––– 10 Hex Nut 1/2”

97708 AIRPLANE TIRE ASSEMBLY (AIR FILLED)50030908 AIRPLANE TIRE ASSEMBLY (FOAM FILLED)

6

3

5

2

1

4

78

67-7-7

77 AUTO RIM5 Hole, 15”

JULY, 2011


67-7-8

5

3

2

1

4

67


1 50051233 1 Tire 29 x 9.0 – 15 / 16 Ply2 50051234 1 Tube 9 x 153 50051235 1 Wheel Flange with Valve Hole4 50051236 1 Wheel Flange without Valve Hole5 –––– 10 Capscrew 1/2” x 1” Gr.56 –––– 10 Lockwasher 1/2”7 –––– 10 Hex Nut 1/2”

50050727 AIRPLANE TIRE ASSEMBLYModel: 3414

JULY, 2011



1 –––– 1 Flatwasher 5/8”2 –––– 1 Capscrew 5/8” x 2”3 –––– 1 Hex Nut 5/8”4 12031 1 Hose Holder Rod

12032 HOSE HOLDER ASSY.


1 53340 1 Adaptor 9/16” JIC to 3/4” SAE2 24-6-434 1 Adaptor 9/16” JIC to 1/2” NPT3 14-40-98 1 90° Elbow 3/4” ORB to 9/16” JIC4 50047240 1 Breather Plug5 62427 1 Hydraulic Hose 144”

HYDRAULIC HOSES & FITTINGS

63451 STOP COLLAR KIT

67-8-1

1817 RATCHET ASSEMBLY


1 50028265 2 Pin2 50028264 4 Clip Pin3 11810 1 Handle4 15474 1 Cotter Pin

3

2

2

2

2

4

1

1

JULY, 2011


67-8-2


1 95429 1 Clevis Cap2 92430 1 Rod Cap3 50017993 1 Piston4 95431 1 Rod 1.25” Dia.5 95426 1 Cylinder Tube6 95427 4 Tie Rod7 95425 2 Pin 1” Dia.8 21020614 4 Cotter Pin 3/16” x 1 1/2”9 95433 1 Thread Lock10 95428 1 Rod Clevis 1.25” x 1”11 95422 1 Set Screw 3/8” x 1/2 Knurled12 95420 8 Hex Nut 5/8” UNF13 95421 1 Hex Nut 1”-1414 95435 1 Plug 3/4”15 95423 1 Caution Decal16 50017623 1 Seal Kit

99565 HYDRAULIC CYLINDER(Was Part No. 95394)Mfd. by Monarch

3.5” Bore x 8” Stroke 1.25 Rod Dia.3/4” – 16 ORB Ports

Replaced by 50047475 Cylinder (Bailey)

87

112 13 3

156

5

2 12

4

10

16

8

119

7

Cylinder Assembly Part Number Stamped Here.

14

JULY, 2011



1 –––– 1 End Clevis2 –––– 1 Gland3 –––– 1 Piston4 –––– 1 Piston Rod5 –––– 1 Cylinder Tube6 –––– 4 Tie Rod7 –––– 2 Clevis Pin8 –––– 4 Cotter Pin9 –––– 1 Rod Clevis Bolt10 –––– 1 Rod Clevis11 –––– 1 Rod Clevis Nut12 –––– 4 Tie Rod Nut13 –––– 1 Piston Nut14 –––– 3 Steel Plug w/ O-Ring15 –––– 1 Warning Decal16 50017623 1 Seal Kit

Cylinder Assembly Part Number Stamped Here.

8

14

112

133 15

16

6

5

2 12

4

10

78

9

11

7

50047475 HYDRAULIC CYLINDER (AXLE ADJUSTING)Mfd. by Bailey

3.50” Bore x 1.25” Rod Dia. x 8.00 StrokeUsed on 3414

67-8-3

JULY, 2011

2501 Griffin Ave. • Selma, AL 36703(334) 872-6261 • (334) 874-2700

Parts Ordering 1-800-304-2836Fax 1-800-572-1784

www.bushhog.com

Sec 67 (3414) - Bush Hog · 5 86666 66DoubleEdgeBlade 6 90563 –––– 1 MountWeldment 7 90537...

Documents

Transcript of Sec 67 (3414) - Bush Hog · 5 86666 66DoubleEdgeBlade 6 90563 –––– 1 MountWeldment 7 90537...