Seals Parts Technician First Period Material Identification and Calculations 270103d.
-
Upload
bennett-powers -
Category
Documents
-
view
214 -
download
3
Transcript of Seals Parts Technician First Period Material Identification and Calculations 270103d.
Seals
Parts Technician
First Period
Material Identificationand Calculations
270103d
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 1 - External and integral seals. (Courtesy SKF Canada Limited)
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 2 - Static seal - valve cover gasket.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 3 - Dynamic seals.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 4 - Gaskets.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 5 - Single-lip seal.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 6 - Single-lip spring-loaded seal.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 7 - Double-lip seal.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 8 - Dual-lip seal with a portion magnified.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 9 - Stainless steel wear sleeve.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 10 - Hydrodynamic seal.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 11 - Split seal.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 12 - Seal with replaceable sleeve.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 13 - Piston rings allow a certain amount of leakage can be tolerated.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 14 - Wind back seals.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 15 - Face seal.
© 2012, Her Majesty the Queen in right of the Province of Alberta
CAUTION
Faces seals cannot be stored on edge or dropped. Finger acid will destroy them.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 16 - Parts of a face seal.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 17 - Dust seal used on rear axle assembly.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 18 - Static diaphragm seal in a vacuum motor.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 19 - Brake chamber with dynamic diaphragm seal.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 20 - Three grades of threadlockers.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 21 - Teflon thread sealers.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 22 - Static seal packing.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 23 - Fabric packing.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 24 - Fabric packing with a braided core.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 25 - Exploded view of a wheel cylinder that uses cup-type seals (packings).
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 26 - V-ring seal. (Courtesy SKF Canada Limited)
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 27 - V-ring packing.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 28 - U-cup packing.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 29 - O-ring assortment kit.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 30 - O-ring seal with a built-in sleeve.
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 31 - Felt seal. (Courtesy SKF Canada Limited)
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 32
a)
b)
c)
d)
e)
f)
© 2012, Her Majesty the Queen in right of the Province of Alberta
Figure 33 - Identification number stamped on a seal.