1. Tap on WIFI icon in the top left corner of thehome screen.

2. Select from the list of available WiFi networks.

3. Enter the WiFi password if required andselect CONNECT.

SECTION 1:PARTS & CHECKLIST

HEAD UNIT HDMI/OBDII CABLE

SECTION 2:PRE-INSTALL CHECKLIST

WIFI INTERNET ACCESS

During the installation process you will need to connect the GTX to the internet using the built-in WiFi.

ALLOW TIME FOR INITIAL SETUP

Make sure you allow up to 30 minutes to complete the initial setup and installation process.

1. Using provided HDMI/OBDII Cable, plugVehicle Interface Module (VIM) into vehicle’sOBDII port commonly found under thesteering column.

2. Connect Mag Cable to VIM using micro USB port.

3. Mount suction cup in your preferred location andattach Mag Cable.

4. Connect the head unit to Mag Cable.

5. Turn vehicle key to the on position.

WIFI IS REQUIRED FOR TUNING.

1. Tap on TUNE from the home screen

2. Turn vehicle key to the on position.

3. The GTX will download the latest files foryour vehicle.

4. If Custom Tunes have been sent to the Derive Cloud,the GTX will display available files. Select the filesyou want to download to this GTX.

5. Select available options. (selecting “DEFAULT” willload stock options).

6. Your GTX has one vehicle license. Tuning thevehicle will use this license.

7. Follow the on screen instructions to complete thetuning process.

Downloading files for your vehicle...

45%

TUNE VEHICLE AVAILABLE CLOUD FILES

CANCEL CONTINUE

Please select Cloud files you would like to download.

Track Tune_6.7L

Tow Tune_6.7L

High HP Tune_6.7L

TUNE VEHICLE

STOCK

TOW

PERFORMANCE

Engine Tune

BACK

Customize your vehicle and adjust for aftermarket upgrades...

Rear TPMS: Stock

Horn Chirp: Stock

Seat Belt Reminder: Stock

CONTINUEBACK DEFAULT

TUNE VEHICLE

Diagnostics

Tune

Updates

Functions

Info

Gauges

SECTION 3:POWERING UP THE GTX

SECTION 4:WIFI SETUP

SECTION 5:TUNING THE VEHICLE

SECTION 5:TUNING THE VEHICLE

PERFORMANCE TUNER & MONITOR

MAG CABLE SUCTION CUP MOUNT

VEHICLE INTERFACE MODULE USB CABLE

In the event that WiFi is not available in thevehicle, disconnect the Head Unit and connect itto a power source within range of WiFi, using theUSB Cable provided.

SECTION 8:CUSTOMIZING YOUR MONITORING EXPERIENCE

Tap anywhere on the screen to edit the configurable layout.

Double tap to customize a specific gauge.LAYOUTChange the layout of the currentgauge screen.

DATASelect the data to monitor.

BRIGHTNESS Change the screen brightness, activate thelight sensor and select day/night themes.

UNITSelect the unit of display for this data.

RESETReset minimum and maximum observeddata values. RANGE

Set the display range for the selected data. RECORD

Record datalog for playback usingLiveLink Software.

ALERTSet visual and audible alerts.

DATASETSelect which set of vehicle data to moni-tor or a DLX (Datalog Configuration).

Barometric Pressure

85 87 1 11

672 2276

-10 4.8

0 2.11

11.36 14.36

86.0Boost

2.02Control Module Voltage

14.17

Engine Fuel Rate

11Engine RPM

2185Fuel Injection Timing

4.4BRIGHTNESS RESET RECORD DATASETLAYOUT

Boost

Control module Voltage

Engine Fuel Rate

Engine RPM

MIN 0.00

MAX 14

UNIT KPA

ALERT OFF

BOOST

UNIT RANGE ALERTDATA

GAUGESMonitor critical engine data in real time and datalog engine functions for playback using the free LiveLink™ software.

FUNCTIONS Adjust vehicle-specific options with on board vehicle functions.

DIAGNOSTICSRead and clear DTCs (Diagnostic Trouble Codes).

INFOView information about your GTX and vehicle includ-ing the current software version, serial number and vehicle information.

UPDATESUpdate your GTX using built-in WiFi. Receive the latestsoftware updates from the Derive Cloud.

WIFIConnect to WiFi to receive the latest updates.

SETTINGSAdjust settings and reset the GTX.

TUNECustomize your vehicle experience with preloaded and custom calibrations.

Diagnostics

Tune

Updates

Functions

Info

Gauges

SECTION 6:HOME SCREEN

SECTION 9:DIAGNOSTICS

SECTION 10:SETTINGSGENERAL

1. START GAUGES AFTER POWER ONGTX will boot to the gauge screen.

2. USER SETTINGS RESETRemoves all user settings includingWiFi information.

3. FACTORY RESETReturns GTX to factory settings andremoves all data from GTX.

READ DTCs:

1. Tap DIAGNOSTICS from the home screen.

2. Select READ DTCs from the menu.

3. Ensure the vehicle key is in the on position.

4. The GTX will display any DTCs available.

5. Select a DTC for more information.

CLEAR DTCs:

1. After selecting DIAGNOSTICS from homescreen, tap CLEAR DTCs.

READ DTC

Turn Key OnTurn the vehicle’s ignition key to the ONposition or push & hold the Engine StartButton for 2-3 seconds.

DO NOT START the engine.

CONTINUE

PO452EVAP SYSTEM PRESSURE SENSOR/SWITCH CIRCUIT LOW

PO463FUEL LEVEL SENSOR CIRCUIT HIGH

PO57CNO ADDITIONAL INFO AVAILABLE

PO625STARTER RELAY A CIRCUIT

READ DTC

EXIT CLEAR DTCs

GENERAL SETTINGS

START GAUGES AFTER POWER ON

USER SETTINGS RESET

FACTORY RESET

USER RESET

RESET

ON

1. Tap on GAUGES from the home screen.

2. Select your vehicle from the list.

3. Default gauges show preselected options. Swipeto move between configurable screen layouts.

GAUGES

2011-2016 Ford Powerstroke 6.7L

2008-2010 Ford Powerstroke 6.4L

EXIT

Barometric Pressure

85 8786.0

Boost

0 2.112.02

Control Module Voltage

11.36 14.3614.17

Engine Fuel Rate

1 1111

Engine RPM

627 22762185

Fuel Injection Timing

-10 4.84.4

SECTION 7:MONITORING: