Schützenstraße 74 · 57271 Hilchenbach, Germany 6.2210 ... · Part no. HCR-9.3792.6610...
Transcript of Schützenstraße 74 · 57271 Hilchenbach, Germany 6.2210 ... · Part no. HCR-9.3792.6610...
08/2015
6.2210Hilma-Römheld GmbHSchützenstraße 74 · 57271 Hilchenbach, Germany
Phone +49 (0) 2733 / 281-0 · Fax +49 (0) 2733 / 281-169 · www.hilma.de
Subject to technical modi� cation
149
Sliding clamp, mechanicalwith integral high-pressure spindle
Applications:
for clamping and locking dies on press beds and rams
on beds of machine tools
when the available space is limited
Function:
The sliding clamp is manually placed in the T-slots and screwed against the die clamping edge. Once the high-pressure spindle has been adjusted to suit the height of the clamping edge, the clamping force is built up by turning the hexagon nut (SW 1) in a clockwise direction. The clamping force achieved depends on the tightening torque selected with the torque wrench.
Special features:
suitable for retro� t
temperature resistance up to 250°C
compact design and easy handling
clamping force of between 40 and 80 kN
high clamping force with low torque
compensates for large clamping edge tolerances
no colliding edges, smooth die positioning
no need for die standardization (width and depth)
Accessory
Torque wrench 20 - 100 NmPart no. HCR-9.3792.6610
High-pressure spindle
Clampingblock
T-slot adapter
Mechanical sliding clamps fastened to a machine bed.
Note:
Before applying the tightening torque, the high-pressurespindle must be screwed against the clamping edge so that there is no play.If the parts are not rigid, tighten the high-pressure spindle using the hexagon nut (SW 2) until there is no play.
Carr Lane Roemheld Mfg Co.927 Horan Drive, Fenton, MO 63026
Phone (636) 386-8022 Fax (636) 386-8034 www.clrh.com/hilma
08/2015
6.2210
�
�
�
�
��
�
�
�
��
��
��
�
���
���
����
����
��
�
�
��
�
SW 1SW 2
18 22 28
40 40 80
1,5 1,5 2,2
45 45 90
104 104 126
65 65 80
40 40 50
19 19 28
63 63 72
50 –106 56 –106 72 –131
24 32 42
25 30 37
10 14 18
18 22 28
50 50 60
28 35 44
M 36 x 3 M 36 x 3 M 48 x 3
21 21 27
30 30 35
13 13 17
30 30 41
3,7 4,0 6,5
HCR-2212-185 HCR-2212-225 HCR-2213-285
18 22 28
25 33 43
30 37 46
10 14 18
24 32 42
HCR-8.2754.1850 HCR-8.2754.2250 HCR-8.2754.2850
HCR-2754-180 HCR-2754-220 HCR-2754-280
HCR-2754-500 HCR-2754-500 HCR-2754-500
Hilma-Römheld GmbHSchützenstraße 74 · 57271 Hilchenbach, Germany
Phone +49 (0) 2733 / 281-0 · Fax +49 (0) 2733 / 281-169 · www.hilma.de
Subject to technical modi� cation
150
Sliding clamp, mechanicalwith integral high-pressure spindle
Example of ordering: 2212-185/ F80
Functional dimension’f’ = 80 (in mm)to be quotedin the order
Sliding clamp, mechanical
T-slot: 18 mmClamping force: 40 kN
T-slot DIN 650 (mm)
Clamping force (kN)
Clamping stroke (mm)
Max. tightening torque (Nm)
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
g (mm)
f min. - max. (mm)
h (mm)
i (mm)
k (mm)
l (mm)
m (mm)
n (mm)
p (mm)
Max. travelling path s (mm)
SW 1 (mm)
SW 2 (mm)
Weight (kg)
Part no.
T-slot DIN 650 (mm)
a (mm)
k (mm)
i (mm)
g (mm)
Parking station, with holder and spacer ledge
Part no.
Holder Part no.
Spacer ledge Part no.
Functional dimension ’f’: die clamping edge + web height of T-slot + 4 mm = dimension ’f’
Distance ’x’: x = f + i - g - 4 mm
Fastening bolt
T-slot adapter
Clampingblock
High-pressure spindle
Parking station accommodates the clamping element during die change
Dimension x to be quoted in the order
Holder
Spacer ledge
Special versions are available on request.D
ie c
lam
ping
edg
e
Web
hei
ght
Clam
ping
str
oke
Carr Lane Roemheld Mfg Co.927 Horan Drive, Fenton, MO 63026
Phone (636) 386-8022 Fax (636) 386-8034 www.clrh.com/hilma
08/2015
6.2212Hilma-Römheld GmbHSchützenstraße 74 · 57271 Hilchenbach, Germany
Phone +49 (0) 2733 / 281-0 · Fax +49 (0) 2733 / 281-169 · www.hilma.de
Subject to technical modi� cation
151
Clamping block, mechanicalwith integral high-pressure spindle
Applications:
for clamping and locking dies on press beds and rams
on beds of machine tools
when the available space is limited
Function:
The high-pressure spindle is manually screwed against the die clamping edge. The clamping force is built up by turning the hexagon nut (SW 1) in a clockwise direction using a torque wrench. The clamping force achieved depends on the tightening torque selected with the torque wrench.
Special features:
suitable for retro� t
temperature resistance up to 250°C
compact design
clamping force of between 40 and 80 kN
high clamping force with low torque
compensates for large clamping edge tolerances
self-locking by patented wedge system
individually usable
clamping block with high-pressure spindle
mounted on spacer ledges
Clamping block with high-pressure spindle,mounted on spacer ledges
Carr Lane Roemheld Mfg Co.927 Horan Drive, Fenton, MO 63026
Phone (636) 386-8022 Fax (636) 386-8034 www.clrh.com/hilma
08/2015
6.2212
�
�
���
l
�
�
�
���
� �
�
���
���
�
�
���
40 80
1,5 2,2
45 90
104 126
65 80
36 43
19 28
83 99
50 57
M 36 x 3 M 48 x 3
40 50
3 3
91 111
24 29
M 16 M 20
24 30
30 35
13 17
30 41
2,3 4,0
HCR-2212-111 HCR-2213-111
Hilma-Römheld GmbHSchützenstraße 74 · 57271 Hilchenbach, Germany
Phone +49 (0) 2733 / 281-0 · Fax +49 (0) 2733 / 281-169 · www.hilma.de
Subject to technical modi� cation
152
Accessory:
Torque wrench 20 - 100 NmPart no. HCR-9.3792.6610
Note:
Before applying the tightening torque, the high-pressure spindle must be screwed against the clamping edge so that there is no play.If the parts are not rigid, tighten the high-pressure spindle using the hexagon nut (SW 2) until there is no play.
Clamping force (kN)
Clamping stroke (mm)
Max. tightening torque (Nm)
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
f (mm)
g (mm)
h (mm)
k (mm)
l (mm)
m (mm)
n (mm)
o (mm)
Max. travelling path s (mm)
SW 1 (mm)
SW 2 (mm)
Weight (kg)
Part no.
This edgemay be removed
Coar
se
adju
stm
ent
Clamping block, mechanicalwith integral high-pressure spindle
Stro
ke
Carr Lane Roemheld Mfg Co.927 Horan Drive, Fenton, MO 63026
Phone (636) 386-8022 Fax (636) 386-8034 www.clrh.com/hilma
08/2015
Hilma-Römheld GmbHSchützenstraße 74 · 57271 Hilchenbach, Germany
Phone +49 (0) 2733 / 281-0 · Fax +49 (0) 2733 / 281-169 · www.hilma.de
Subject to technical modi� cation
1536.2212.US
Sliding Clampmechanical with integratedhigh pressure spindle, inch/ASA T-slot
For T-slot 11/16 13/16 13/16 1-1/16 1-5/16Clamping force (lbs) 9,000 9,000 18,000 18,000 18,000
Max. tightening torque (ft-lbs) 33 33 67 67 67Max. stroke (in) 0.059 0.059 0.086 0.086 0.086
a (in) 4.094 4.094 4.567 4.567 4.567b (in) 2.559 2.559 3.150 3.150 3.150c (in) 1.575 1.575 1.969 1.969 1.969d (in) 0.787 0.787 1.102 1.102 1.102e (in) 1.250 1.250 1.890 1.890 1.890f (in) 2.992 3.150 3.937 4.213 4.567
g (in) 0.787 1.024 1.024 1.417 1.811h (in) 1.024 1.181 1.181 1.457 1.811i (in) .0394 0.512 0.512 0.709 0.945
k (in) 0.6480.658
0.7730.783
0.7730.783
1.0811.033
1.2581.273
l (in) 2.4803.228
2.4803.228
3.0314.213
3.0314.213
3.0314.213
m (in) 1.1021.122
1.2601.299
1.2601.299
1.6141.654
2.0082.047
n (mm) M36x3 M36x3 M48x3 M48x3 M48x3o (in) 0.118 0.118 0.118 0.118 0.118p (in) 3.740 3.740 4.370 4.370 4.370
Part no. clamp HCR-2212-111 HCR-2212-111 HCR-2213-111 HCR-2213-111 HCR-2213-111Part no. T-slot adapter HCR-2221-050 HCR-2223-050 HCR-2223-060 HCR-2225-060 HCR-2227-060
Clamping system, laterally mounted on spacer ledges and centrally mounted on moveable T-slot adapters.
Application and selection:1. Determine web height: (w) of T-slot (i.e.
web height for 13/16“ T-slot can vary 1/2“ according to ASA B5.1 1949)
2. Determine clamping edge heights of tools (x), standardize if necessary.
3. The functional dimension (f ) is a result of web height, clamping edge heights and 1/2 of the threaded adjustment [(lmax-lmin)/2].
f = w + x + [(lmax-lmin)/2] + .118 *Please specify (w) & (x) dimensions when
ordering.
Carr Lane Roemheld Mfg Co.927 Horan Drive, Fenton, MO 63026
Phone (636) 386-8022 Fax (636) 386-8034 www.clrh.com/hilma