Schindlersalmeron 2014 en

Catalogue 2014

CONTACT schindlersalmerón Badenerstrasse 585 CH-8048 Zürich www.schindlersalmeron.com Your point of contact: Margarita Salmerón Espinosa [email protected]

www.schindlersalmeron.com

This light, stackable stool is made from three identical, thin sheets of steel, which stabilise one another as they fold three-dimensionally.

The three parts are joined by a grommet connection specially designed by schindlersalmerón, which also serves as a finger-hold and helps prevent scratching when the stools are stacked. Both practical and comfortable, the stool can be used in many ways. The material is easily cleaned and is suited for use outside as well as in wet rooms.

40 cm43.5 cm

44 cm

36 cm

Steel sheet 1 mm, powder-coated

Colours: white, black, yellow or redFor orders over 10 pieces, other RAL colours are available

Feet caps: plastic, white or black

Weight: 2 kg

Serial production 2008, new grommet joint 2012BLICKFANG Design Award ’09 Bronze

Delivery time: ca. 1 week

3T-STOOL

Until the industrial revolution and its demand for standardisation, the forked branches were a valuable raw material. The way these elements are loaded on the tree means they make particularly strong and elastic connections between two parts. The branch stool is a case study that pursues the question as to how successfully can forked branches be combined with contemporary information technology to become relevant again. Forked branches are more or less alike, but not identical and so require another approach to tolerances, which impacts on how the connections to the seat are made.

35 cm43.5 cm

40 cm

Limited series: 15 pieces

Seat: MDF, powder-coated whiteLegs: 3 Beech forked branches from Zurich City Forest Weight: 2 to 2.5 kg

Production 2013

BRANCH STOOL



34 cm

2 cm

Calf leather, hand-stitchedUnderside: roughened leather, non-slip

Filling: two layers of foam: 2 cm thick

Colours: black, red, yellow or brown

For orders over 30 pieces other colours are avail-able

Weight: 0.5 kg

Serial production, 2009

Delivery time: ca. 1 week

¡COJINES!

Designed for the Flank-Milled chairs, this calf leather seat cover also fits other objects well.

On the underside, the leather is turned outwards. The rough surface prevents any unintended slippage, whilst at the same time the cushion can always be easily lifted up.

The two layers of foam give an optimal comfort for sitting. A perfect finish for the leather is not the intention, and any natural imperfections are left in tact.


47 cm 41 cm

46 cm

38 cm

12 cm

86 cm

Craftsmanship and contemporary technology are combined in this wooden chair. The joints in the frame are glued mortise and tenon. The rear legs are made with flank-milling technology, which gives the chair its elegant, unmistakable outline.

FLANK-MILLED CHAIR F/01

Oak, oiled or stained blackFrame, legs and backrest: European solid wood, PEFC-certifiedSeat: Beech plywood 5 mm, veneered

For orders over 30 pieces: other finishes / coloursand other kinds of wood are available.With floor-protecting teflon padsOptionally upholstered in leather or felt

Weight: 3.5 kg

Strength and durability certified by CATAS, (DIN EN1728:2000)

Serial production, 2008Part of the Design Collection at the Museum ofDesign, Zurich

Delivery time: ca. 2 weeks


106 cm

68 cm

The F/02 is the stackable version of the F/01. The rear legs have the same elegant form as the F/01, but are gently swung outwards. Because of this, the stacking of several chairs is possible. Accordingly the F/02 is also attractive for use in larger, public / commercial settings.


Oak, oiled or stained blackFrame, legs and backrest:European solid wood, PEFC-certifiedSeat: Beech plywood 5 mm, veneered

For orders over 30 pieces, other finishes / coloursand other kinds of wood are available.

With floor-protecting teflon padsOptional upholstery in leather or felt

Weight: 4 kg

Strength and durability certified by CATAS (DIN EN 1728:2000)




With the F/05, the family of Flank-Milled Chairs is extended to create a version with armrests. Both beautiful in form, as well as functional, the chair is characterized by its typically elegant flank-milled shape. The rather wide seat, and the armrests are tailored to the highest standards of comfort.That the chair can be stacked up to seven chairs extends the use of this chair in public / commercial settings.





Weight: ca. 5 kg




46 cm

86 cm

58 cm48 cm






Weight: ca. 5 kg




The Flank-Milled Chair F/08 is another variant in our Flank-Milled family. A taller plywood backrest relieves the back especially well, and with its relatively light weight this chair is perfectly suited for use in public/commercial settings. The armrests are ergonomically designed as supports, both when seated and in standing up. The chair is dimensioned so that even though it has armrests it fits well under the F/03 Table.


The F/03 complements the Flank–Milled series with a table of cubic proportions, whose legs continue the motif of the Flank-Milled Chairs in their gentle curvature on their inner side.Stackable and light, the table is suitable for both domestic and larger, public/commercial settings.

FLANK-MILLED TABLE F/03

Frame, legs and cap strip:European solid wood, PEFC-certified

Table top: 12 mm plywood, veneered

Oak, clear varnished (PUR-varnish) or stained black

For orders over 5 pieces, other finishes / coloursand other kinds of wood are available

Weight: 11 kg



Delivery time: ca. 6 Weeks

75 cm 75 cm


With the Flank-Milled Stool F/06 the theme of the Flank-Milled family was translated into a stool design. The four legs elegantly encompass a lower sheet-steel ring and curve upwards to the seat.

FLANK-MILLED STOOL F/06

Oak, oiled or stained blackFrame and seat: European solid wood, PEFC-certifiedLower ring: sheet-steel, powder coated

For orders over 20 pieces, other finishes / coloursand other kinds of wood are available

With floor-protecting teflon pads

Weight: ca. 7 kg


Delivery time: ca. 3 Weeks

75 cm

35 cm

56.5 cm


The F/04 extends the Flank-Milled series to a table for mass-customisation, whose legs pick up the motive of the Flank-Milled chairs with a gentle curve on their inside. The proportions and the dimensions can be adjusted according to clients’ needs, the gentle curve of the long edge subtly brings the focus of everyone at the table towards the centre. This table is suited for use both in domestic as well as public/commercial settings.

FLANK-MILLED TABLE F/04

Frame, legs, table top and cap strip: European solid wood, PEFC-certified

Wood type and finish can be freely chosen Made-to-order production, 2011 Delivery time: ca. 6 weeks

200-295 cm

74 cm


This flat, purist coat rack is a classic “serialbespoke object” for furniture. It is manufactured in bespoke lengths, for the same cost as a serial production.

With its minimal projection from the wall, the rail fits into even the narrowest corridors. With the included mounting kit, it is fitted to the wall in only a few steps.

In the light-enabled version of the Clothes Rail, an LED-strip is fitted to the inner side with silicone, which indirectly illuminates the wall, creating a comfortable light. It was developed in collaboration with Fontana– Leuchten.

2.5 mm brushed stainless steel, laser-cut and folded

Bespoke lengths can be manufactured of between 40 and 285 cm, in 0.5 cm increments

Over 150 cm: an additional central fixture is necessaryProjects 5.5 cm from the wall

Weight: 2.1 kg per linear metreA 1-m rail holds up to 33 hangers with rotating hooksLighting: LED-strips, 12 VoltLight colours: warm white, yellow, red, green or blue or RGB-version: with remote control, 15 cm without breaks

Power cord: 2 m long, can be connected to eitherside of the unit


Part of the Design Collection of the Museum ofDesign, Zurich

Order before the 15th of the month for delivery inthe last week of the month

CLOTHES RAIL K/01

8 cm

5.5 cm


The Clothes Rail K/02 is tailored for the direct hanging of jackets without the need for hangers.

It is produced from a single piece of stainlesssteel and can be manufactured in bespoke lengths as a “serial bespoke object”. The spacing between the hooks is not strictly modular, but rather is, almost imperceptibly, adjusted to the desired length.

In the light-enabled version of the Clothes Rail, an LED-strip is fitted to the inner side with silicone, which indirectly illuminates the wall, creating a comfortable light. It was developed in collaboration with Fontana– Leuchten.

1.5 mm brushed stainless steel, laser-cut and folded

Custom lengths between 60 and 295 cm

Projects 8 cm from the wall

Weight: 2.1 kg per metre

1 m clothes rail K/02: 21 hooks, 20 hangers

Lighting: LED-strips, 12 VoltLight colours: warm white, yellow, red, green, blue2-pole power cable, 2 m, transparent with rocker switch, can be connected to either the right or the left side of the unit


Order before the 15th of the month for delivery inthe last week of the month

CLOTHES RAIL K/02


The Paper Collector is a clever solution for the bundling of newspapers: thanks to the four slots, old paper can be tied together directly in the collector itself, rearranging or turning the pile is no longer necessary.

With its laconic shape and strong colours, the Paper Collector is an object which even gives an unbound pile of newspapers an attractive form.

1.5 mm sheet steel, powder-coated

Colours: yellow, red, white

For orders over 5 pieces, available in other RAL colours

Handles: PVC-P, blackJoints: polyamide, black

Weight: ca. 3 kg


Delivery time: 3 weeks

PAPER COLLECTOR

35 cm

26 cm 17 cm

26 cm


Consists of two frames connected by a joint in the middle.

The angle can be freely adjusted, enabling different table variations and uses. The frames are light and can be folded flat. Soft, black plastic caps prevent the slipping of the table top.

71 cm

75°

TABLE FRAME

Flattened-oval steel tube

Colours: black or white, powder-coated

Other RAL-colours for orders over 5 pieces

Caps: plastic, blackFeet: plastic, black, easily adjusted in height

Available in two sizes:

Size 1: 10 kgSize 2: 11 kg

Serial production, 2006/2013


Schindlersalmeron 2014 en

Documents

Transcript of Schindlersalmeron 2014 en