SCBP Quick Start Guide

7
An ideal Partner in Your Growth w w w . a z c o m . i t TMDXSCBP6618X - Small Cell Base Station Platform Quick Start Guide USB JTAG UART Cable Jack Reset Button LED 2 LED 3 Backhaul Ethernet Debug Ethernet Power DIN LED 1 Debug LEDs DIP SW S4 DIP SW S1 DIP SW S3 DIP SW S2 FPGA LED 2 FPGA LED 1 JTAG Connector C6A8167 TCI6618 AIF2 SFP-1 AIF2 SFP-2 Future Use J24 Connector

Transcript of SCBP Quick Start Guide

Page 1: SCBP Quick Start Guide

An ideal Partner in Your Growth

w w w . a z c o m . i t

TMDXSCBP6618X - Small Cell Base Station Platform

Quick Start Guide

USB JTAG

UART Cable Jack

Reset Button

LED 2

LED 3

Backhaul

Ethernet

Debug

Ethernet

Power DIN

LED 1

Debug LEDs

DIP SW S4 DIP SW S1 DIP SW S3

DIP SW S2

FPGA LED 2

FPGA LED 1

JTAG Connector

C6A8167

TCI6618

AIF2 SFP-1

AIF2 SFP-2

Future Use

J24 Connector

Page 2: SCBP Quick Start Guide

TMDXSCBP6618X Quick Start Guide

The TMDXSCBP6618X includes:

� TMDXSCBP6618X

� Power supply

� Power cord & Universal Adapter (USA, UK, Europe)

� Mini B USB cable for on-board JTAG emulation

� Ethernet cable

� UART cable (Audio Jack to DB-9)

� Documentation

Before starting:

• Check integrity of the packaging

• Open the package and check that all the parts listed above are present and undamaged

• Execute the steps described below

1

Set DIP SWITCH S1 in order to select USB JTAG or 20 pin connector JTAG

(switch position 9) and if JTAG must be connected to TMX320C6A8167 or

TMX320TCI6618X (switch position 2). The board supports only one JTAG

chain at a time.

Switch S1: TMX320TCI6618X - USB

JTAG

Switch S1: TMX320TCI6618X - 20 pin

connector JTAG

Switch S1: TMX320C6A8167 - USB

JTAG

Switch S1: TMX320C6A8167 - 20 pin

connector JTAG

Page 3: SCBP Quick Start Guide

TMDXSCBP6618X Quick Start Guide

2

Set DIP SWITCH S2 and S3 as shown in the figures below. TMX320C6A8167 will

boot from NAND flash. For TMX320TCI6618X both configurations are described

(“No boot” and “Network boot”).

3 Set DIP SWITCH S4 as shown in the figure below to set standard JTAG mode.

Other configurations are reserved for future use. If necessary, select endianness

with a jumper on J24 connector, position 5-6 (close: BIG ENDIAN, open: LITTLE

ENDIAN)

Switch S4: Standard JTAG

Switch S2: NAND Boot

(TMX320C6A8167)

Switch S3: No boot

(TMX320TCI6618X)

Switch S3: Network boot

(TMX320TCI6618X)

Connector J24: Endianess

Page 4: SCBP Quick Start Guide

TMDXSCBP6618X Quick Start Guide

4

Connect the UART cable to the UART cable jack for console monitoring.

5

Connect the MINI-USB cable or 20-pin JTAG connector (as selected in Step 1)

for on board embedded emulation.

6 Connect your PC (or Ethernet switch/router) to the Gigabit Ethernet port (RJ1)

using the supplied Ethernet cable.

7

Connect the 12V DC power supply to power jack (J1).

Warning: Power ON and Power OFF procedures require disconnection of Switching

Power Supply. In order to reduce mechanical stress of the DIN connector J1, please

leave it plugged together. To turn off the power, unplug the power cord from the

Switching Power Supply (or disconnect the plug from the socket).

Page 5: SCBP Quick Start Guide

TMDXSCBP6618X Quick Start Guide

Getting Started

When the TMDXSCBP6618X is powered, it executes some procedures to load FPGA

and check hardware functionalities. Looking at the LEDs during start-up phase you

can verify that the start-up procedure is successfully completed.

- LED 1 (GREEN): this is the Power LED. When Power Supply is connected this

LED must be switched ON.

- LED 2 (RED): this LED blinks during board start-up phase, then it is turned

OFF.

- LED 3 (GREEN): this LED is turned ON after FPGA start-up phase completion.

It shows that board is up and running.

- Diagnostic LEDs: these LEDs are turned ON during start-up phase. They must

be OFF after start-up completion.

- FPGA LED 1: this LED (RED) blinks during FPGA programming phase, then it’s

turned OFF if FPGA is successfully loaded.

- FPGA LED 2: this LED (GREEN) shows FPGA status. It is turned ON after FPGA

is successfully loaded.

Page 6: SCBP Quick Start Guide

TMDXSCBP6618X Quick Start Guide

After this phase, TMX320C6A8167 Reset Code is executed by the Bootloader and

the LINUX is loaded. If you are connected with the console cable, you can monitor

software initialization.

At the end of the procedure, Linux prompt should be available.

U-Boot 2010.06 (May 13 2011 - 21:23:58)

TI8168-GP rev 1.0

ARM clk: 987MHz

DDR clk: 398MHz

DRAM: 2 GiB

NAND: HW ECC Hamming Code selected

256 MiB

###### ###### ######## ########

## ## ## ## ## ## ## ##

## ## ## ## ## ##

###### ## ######## ########

## ## ## ## ##

## ## ## ## ## ## ##

###### ###### ######## ##

Net: Detected MACID:64:7b:d4:6c:ca:9e

Ethernet PHY: GENERIC @ 0x01

DaVinci EMAC

Hit any key to stop autoboot: 1 ��� 0

NAND read: device 0 offset 0x280000, size 0x440000

Skipping bad block 0x004a0000

4456448 bytes read: OK

## Booting kernel from Legacy Image at 81000000 ...

Image Name: Arago/2.6.37-r0/tmdxscbp6618x

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 1964096 Bytes = 1.9 MiB

Load Address: 80008000

Entry Point: 80008000

Verifying Checksum ... OK

Loading Kernel Image ... OK

OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Linux version 2.6.37 (a0875269@gtrgwdeb) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 Fri May 13

20:50:35 EDT 2011

CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f

CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache

Machine: tmdxscbp6618x

bootconsole [earlycon0] enabled

reserved size = 0 at 0

Memory policy: ECC disabled, Data cache writeback.

.

.

.

INIT: Entering runlevel: 5

Starting system message bus: dbus.

Starting telnet daemon.

Starting syslogd/klogd: done

Starting thttpd.

_____ _____ _ _

| _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_

| | _| .'| . | . | | __| _| . | | | -_| _| _|

|__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_|

|___| |___|

Arago Project http://arago-project.org tmdxscbp6618x ttyO0

Arago 2011.02 tmdxscbp6618x ttyO0

tmdxscbp6618x login:

Page 7: SCBP Quick Start Guide

TMDXSCBP6618X Quick Start Guide

Online Documentation

Most of the documentation on TMDXSCBP6618X is available online at the following

link:

http://www.azcom.it

Select Support menu and then TMDXSCBP6618X item.

TMDXSCBP6618X Information

The link contains:

- User Guide

- Hardware details

- FPGA downloads

- TMX320TCI6618X & TMX320C6A8167 datasheets

- Frequently Asked Questions (FAQ)

Azcom Technology Address

Azcom Technology s.r.l.

Centro Direzionale Milanofiori

Strada 6 - Palazzo N2

20089 Rozzano (MI) - Italy

Tel. +39-02.82450311

Fax: +39 02 57512632

Web: www.azcom.it

e-mail: [email protected]