Scanner Assembly - Including the ADF, and Accociated...

1 HP Ersatzteile für LaserJet 3380

+49 (0) 3723 / 6678 - 0

Scanner Assembly - Including the ADF, and Accociated Covers

1

10

9 4

10

5 6

10

9

2

8 11

3 7

10

12

10

10

Part Number Description

C9143-60109

Q2660-60143

C9124-40002

C9124-40003

C9124-40005 C7296-00014 C9143-60102 C9124-0002

Q2657-60001

0515-4672

0515-4671

0515-4257

Q2660-60103

10

Ref

1

2

3

4

5

6

7

8

9

10

11

12

Automatic document feeder (ADF) and flatbed scanner lid - Includes the lid, the ADF feed mechanism, and

scanner input tray - Mounts on top of the flatbed scanner

Flatbed scanner assembly

Left scanner cover - Mounts on the left end of the scanner assembly - Covers the scanner formatter PC board

Right scanner cover - Mounts on the right side of the scanner assembly

Retainer frame (U-shaped) - Retains the small piece of glass that is used with the ADF assembly - Mounts

on the left end of the scanner assembly

ADF glass window (ONLY) - Small glass window that mounts on the left end of the scanner assembly - Used

when scanning documents from the ADF assembly

Paper input tray for the ADF assembly - Mounts on top of the ADF assembly - Includes the width adjust-

ment side rails

RFI sheild for the scanner controller PC board assembly

Scanner control board assembly - Includes the PC board and interconnecting flat flexible cable

Pan head plastite screw with washer - M4.0 x 1.75, 13.1mm long, Number 2 Phillips recess - Steel, nickel

plated fnish - For securing the scanner to the printer (four used)


plated fnish

Pan head taptite screw with washer - M3.0 x 0.5, 6mm long, Number 2 Phillips - The single black

screw (of the three screws) that secure the scanner formatter PC board assembly to the scanner case

Flat flexible cable (FFC) and RFI shield assembly - Includes the flat flexible cable and its wrap-

around RFI shield - Interconnects the flatbed scanner assembly to the printer formatter board


+49 (0) 3723 / 6678 - 0

Scanner Assembly - ADF Rollers and Separation Pad

2

5 4

4

3

1

Ref

1


C7309-60091

2 C7309-40153

3

4

5

C7309-60009

0624-1055

C7309-40013

C7309-80013

ADF PICK ROLLER ASSEMBLY - INCLUDES TWO ROLLERS IN A BRACKET ASSEMBLY - Moves the frst few

top pages of the input stack into the ADF assembly where the top page is picked off and feed to the pre-

scan drive rollers

Cleanout assembly strip - Green plastic bar with two grab tabs - Can be removed to help clear paper

jams in the automatic document feeder assembly - Snap locks on the back side (far left side) of the ADF

assembly and runs the full width of the paper path

ADF SEPARATION PAD ASSEMBLY - Works with the pick roller assembly to separate the paper stack into

individual sheets - Mounts below the pick roller in the ADF assembly

Pan head plastite screw - 2-28 thread, 0.312 inches long, T8 torx - Used to secure the separation pad

assembly in the ADF assembly (two used)

Paper sensor flag - Senses when there is a document in the automatic document feeder input tray -

Mounts in the top of the ADF cover

Torsion spring - For the ADF paper sensor flag - Provides a slight amount of back pressure so the flag will

not mistakenly indicate a document

Scanner Assembly - Control Panel Assembly

5

3 1

4

2 6

6

6


+49 (0) 3723 / 6678 - 0

Ref

1

2

3

4

5

6


C9124-40006

Q2660-60104

Q2660-60101

C9124-60113

Q2660-67905

0515-4671

Support Chassis - Curved plastic piece that supports the control panel keypad - Mounts to the front of the

printer

Flat flexible cable (FFC) - Interconnects the control panel assembly to the scanner control board

Control panel keypad assembly - Has ‚Copy', ‚Print', ‚Scan' and ‚Fax' function keys - Does

NOT include the bezel - Mounts in the support chassis on the front of the scanner assembly

Speaker assembly - Includes the speaker and cable - Mounts in the lower part of the control panel support

chassis

Control panel bezel - Oval shaped plastic piece with cutouts for the control function keys and display (German)


plated fnish

External Covers

1

3

4

11

5

6

10

7

9

8

2 2

2

Ref

1

2

3

4

5

6

Part Number

XA9-1583-000CN

XA9-1503-000CN

RC1-2391-000CN

RC1-2392-000CN

RF0-1100-030CN RG0-1116-000CN

Description

M4 truss head (flanged) phillips/hex combo drive screw - 12mm long - (S1) Used to secure the top

cover to the print engine frame

M3 truss head (Flanged) phillips screw (Black oxide fnish) - 6mm long - (S6) Typically used to secure

plastic parts and the support pan to the metal side plates

Left height guide - Plastic channeled strip with locking tab - Mounts in the paper exit slot on the top cover

Right height guide - Plastic channeled strip with locking tab - Mounts in the paper exit slot on the top cover

Top cover assembly - Has face-down paper output tray molded into it - Mounts to top of printer - Pro-

vides mounting support for the scanner assembly

Right side cover assembly - Has molded-in air intake louvers


+49 (0) 3723 / 6678 - 0

Ref

7

8

9

10

11

Part Number

RG0-1115-040CN

RA0-1450-020CN

RA0-1470-000CN

RG0-1113-000CN

RG0-1114-000CN

Description

Toner cartridge door - Fold down door used when accessing the toner cartridge - Mounts to the top

of the front cover

Front cover - Lower front of printer - With opening for inserting the paper input tray assembly

Support frame - Curved plastic support piece - Mounts on the bottom left side of the printer (below

the left side door)

Left side door assembly - Provides access to connect the printer interface cables - Includes door and

hinge

Rear cover assembly - Includes rear cover and fold down face-up (or straight through) paper output

tray (tray is NOT sold separately)

Paper Input Tray Assembly

2

1

1

3

Ref

1

2

3

Part Number

XB4-7300-809CN

RG0-1122-000CN

RG0-1121-000CN

Description

M3 self-tapping pan head phillips screw (Black oxide fnish) - 8mm long - (S11) Used to secure the

width adjusters to the arms on the top cover for the paper input tray

Paper tray cover assembly - Includes clear plastic cover with blue width adjustment guides for ‚prio-

rity' paper input

Printer input paper tray assembly - Includes bottom tray, blue paper length adjustment lever, and

extension arm (does NOT include the paper tray cover)


+49 (0) 3723 / 6678 - 0

Internal Components (1 of 2) 3

4

7

5 6

8

10

1 11

13

12

17 2

19

16 9

18 14

19 20

23 21

24 22

19

15

2

Ref

1

2

3

4

5

6

7

8

9

10

11

12

Part Number

XA9-1495-000CN

XA9-1503-000CN

RA0-1182-000CN

RA0-1169-000CN

RK2-0185-000CN

RM1-0832-000CN

RA0-1452-000CN

RM1-0551-000CN

RC1-2195-000CN

RM1-0550-000CN

RL1-0303-000CN

RM1-0835-020CN

13 RM1-0838-000CN

Description

Wafer head machine screw - M3, 6mm long, No. 2 Phillips recess - Secures metal to sheet metal



Shutter lever - Spring loaded lever - Mounts to the top of the laser/scanner assembly

Compression spring - Provides tension for the shutter lever - Mounts between the shutter lever and

the laser/scanner assembly

Flat flexible cable (FFC) - Interconnects the laser/scanner assembly to the printer formatter board

Cable assembly (four-wire) - Interconnects the laser/scanner assembly motor to the printer formatter

board

Front cover support (L-shaped) - Mounts on the upper right corner of the right side plate

Gear/clutch assembly kit - Includes double-gear body, shaft attachment piece and spring - For driving

the paper feed roller

Guide - For the shutter lever on the laser/scanner assembly - Mounts on the metal support bracket

for the laser/scanner assembly

Transfer roller assembly - Transfers static charge to the media being printed on - Mounts in the top of

the paper feed guide assembly

Paper pickup roller (D-shaped roller) - Picks up media from the paper input tray - Clips in the holder

on the paper pickup shaft

Right side plate assembly - Includes the right side plate, drive motor, most all drive gears, and cam

levers - Does not come with the pickup roller solenoid or 69 tooth gear - Right side of the internal

printer mechanism

Paper pickup assembly - Includes the pickup roller, paper feed roller assembly, separation pad, plastic

housing and other associated parts - Mounts in the bottom rear of the printer


+49 (0) 3723 / 6678 - 0

Ref

14

Part Number

RM1-0833-030CN

RM1-0834-030CN

RM1-0836-020CN

RA0-1444-000CN

Q2658-67901

15

16

17

18

19

20

0515-2908

Q2660-00002

C9138-60001

21

22

23

C9138-60002

C9126-60103

C9126-40003

C9126-00001

Description

Print engine control board - Provides motor drive, paper motion monitoring, printing control and po-

wer supply

Print engine control board - Provides motor drive, paper motion monitoring, printing control and po-

wer supply

Left plate assembly - Left side of internal printer mechanism - The printer formatter board mounts to

this plate

Front cover support (L-shaped) - Mounts on the upper left corner of the left side plate

Printer formatter board - Controls the logic and timing operation of the printer, translates the control

panel input, and provides control of the scanner assembly - Does NOT include the LIU board - Mounts

on the left side of the printer

Pan head machine screw with washer - M3.0 x 0.5, 6mm long, Number 2 Phillips - Used to mount the

formatter PC board and shield to the left side plate (fve used)

Upper RFI shield - Mounts over the printer formatter board on the left side plate asssembly

Line interface unit (LIU) board - provides telephone communications (for fax capabilities) to the prin-

ter - For the United States and World Wide EXCEPT Europe - Mounts on the printer formatter board

shield on the left side of the printer

Line interface unit (LIU) board - provides telephone communications (for fax capabilities) to the prin-

ter - For Europe ONLY - Mounts on the printer formatter board shield on the left side of the printer

Ribbon flex cable - From line interface unit PC board to printer formatter PC board

PC board cover - Rectangular shaped plastic pan - Covers the line interface unit (LIU) board - Mounts

to the RFI shield for the printer formatter board

Ground strap - Small metal plate with two screw holes - Mounts to the back of the line interface unit

(LIU) board

Internal Components (2 of 2) 1

3 1

12

4

13

1

2 5

7 6

1

8

9

11

7 10


+49 (0) 3723 / 6678 - 0

Ref

1

2

3

4

5

6

7

8

9

Part Number

XA9-1495-000CN

XA9-1503-000CN

RA0-1447-020CN

RA0-1088-000CN

RA0-1176-000CN

Description




Right side fuser bracket (L-shaped)

29 tooth gear - Mounts on the end of the pressure roller - Largest of the three gears on the fusing

assembly

69 tooth gear - Large gear with ribs and six small holes - Mounts on on a rod in the upper rear corner

of the right side plate

RM1-0846-000CN Fan Assembly - Includes the tubeaxial fan and the plastic mounting bracket/airflow guide - Mounts to

the right side plate assembly

RA0-1457-000CN

RK2-0064-000CN

Connecting link - Connects between the sliding linkage on the left and right side plates and the toner

cartridge access door (two used)

24VDC Solenoid - Engages the pickup roller gear/clutch assembly - Mounts on the right side plate

assembly

RM1-0835-020CN Right side plate assembly - Includes the right side plate, drive motor, most all drive gears, and cam


printer mechanism

RA0-1451-000CN Front guide assembly - Ribbed plastic piece that runs the width of the printer - Mounts to the front of

the left and right side plates

10

11

12

13

RM1-0836-020CN Left plate assembly - Left side of internal printer mechanism - The printer formatter board mounts to

this plate

RM1-2076-030CN Fusing assembly - Bonds toner to paper with heat - For 220V to 240VAC operation -

RA0-1446-020CN Left side fuser bracket (L-shaped)

Right Side Plate Assembly

3

2

4

1

9

5

6

8

7

1


+49 (0) 3723 / 6678 - 0

Ref

1

2

3

Part Number

XA9-1495-000CN

XA9-1503-000CN

Description




4

RM1-0835-020CN Right side plate assembly - Includes the right side plate, drive motor, most all drive gears, and cam


printer mechanism

WT2-5694-000CN Snap-in cable clamp - Secures the cable from the fan assembly to the right side plate, the motor cable

from the laser/scanner assembly to the left side plate, and the drive motor cable to the metal support

pan (three used)

RA0-1212-000CN

RA0-1172-000CN

RK2-0063-000CN

5851-1172

5851-1172

Tension spring - Provides tension for the linkage which engages the toner cartridge drive gear -

Mounts on the right side plate

17 tooth gear assembly - Includes the 17 tooth gear mounted on a black plastic lever/bracket -

Mounts to the right side plate

DC stepper motor assembly - Drives all rollers and fusing assembly via the gear train on the right

side plate

Service parts kit - Includes the left and right toner cartridge guides and their retaining clips - Mounts

toward the top center of the respective internal left and right side plates



5

6

7

8

9

Left Side Plate Assembly 2

3

4

6

5

1

Ref

1

2

3

Part Number

XA9-1495-000CN

RM1-0836-020CN

WT2-5694-000CN

4

5

6

5851-1172

RA0-1197-000CN

5851-1172

Description


Left plate assembly - Left side of internal printer mechanism - The printer formatter board mounts to

this plate

Snap-in cable clamp - Secures the cable from the fan assembly to the right side plate, the motor cable


pan (three used)



Rubber foot




+49 (0) 3723 / 6678 - 0

Engine Control Board and Support Pan

2

3

4

1

2

4 5

6

Ref

1

2

3

Part Number

XA9-0828-000CN

XA9-1420-000CN

Description

M3 pan head phillips screw with captive star washer - 4mm long - (S2) One of two size screws used to

secure the print engine control board to the support pan (This one is nearest the power receptacle)

M3 pan head phillips screw with captive flat and split-lock washers - 8mm long - (S3) Used to secure

the print engine control board to the support pan

RM1-0833-030CN Print engine control board - Provides motor drive, paper motion monitoring, printing control and po-

wer supply

RM1-0834-030CN Print engine control board - Provides motor drive, paper motion monitoring, printing control and po-

wer supply

RA0-1128-000CN Printed circuit board spacer - Mounts between the engine control PC board and the metal support pan

(six used)

4

5 WT2-5694-000CN Snap-in cable clamp - Secures the cable from the fan assembly to the right side plate, the motor cable


pan (three used)

RA0-1127-000CN Support pan (case) for the engine controller PC board - Metal pan which also acts as part of the bot-

tom of the printer

6


+49 (0) 3723 / 6678 - 0

Paper Pickup Assembly (1 of 2)

2

9

8

7

6 1

5

4

3

Ref

1

2

3

4

5

Part Number

XA9-1421-000CN

Description

M4x14 screw - (S4) Used in the paper pickup assembly and the fusing assembly (typically to secure

plastic to plastic parts)

RM1-0838-000CN Paper pickup assembly - Includes the pickup roller, paper feed roller assembly, separation pad, plastic


RM1-0533-000CN Paper pickup shaft assembly - Includes the shaft, the two cams, pickup roller holder, and end cap -

Mounts in the paper pickup assembly

RM1-0851-000CN Paper sensor board - Small board with optical flag sensor (flag not included) - For sensing leading

edge of paper - Mounts on the paper feed assembly in the paper pickup assembly

RM1-0839-000CN Paper feed roller assembly - Includes feed roller, feed roller base assembly, retainer bushings, paper

input leading edge sensor, sensor flag and spring - Mounts on the bottom of the paper pickup assem-

bly

RA0-1072-000CN

RA0-1035-000CN

RA0-1200-000CN

RY7-5081-000CN

Grounding Plate - L-shaped, spring steel - Mounts on the left end of the paper pickup assembly

Torsion spring - Provides high voltage connection to the toner cartridge (developing cylinder) - Mounts

between the paper pickup roller and the transfer roller on the left side of the paper pickup assembly

Torsion spring - Provides high voltage connection to the toner cartridge (primary charging roller) -

Mounts behind the transfer roller on the left side of the paper pickup assembly

Gear/clutch assembly kit - Includes double-gear body, shaft attachment piece and spring - For driving

the paper feed roller

6

7

8

9


+49 (0) 3723 / 6678 - 0

Paper Pickup Assembly (2 of 2)

2

7

7

5 3

4

1

1

6

Ref

1

2

3

4

5

6

Part Number

XA9-1418-000CN

XA9-1421-000CN

Description

M3x6 TP screw - (S12) Used to secure the plastic brackets on each side of the paper pickup roller to

the metal plate



RM1-0838-000CN Paper pickup assembly - Includes the pickup roller, paper feed roller assembly, separation pad, plastic


RM1-0840-000CN Paper lift plate assembly - Plastic plate assembly that includes the two blue paper width adjusters

- Mounts to the front of the paper pickup assembly

RA0-1003-000CN

RC1-1794-000CN

Rubber foot - For bottom of printer - Three used

Sub-pad arm - Small curved plastic arm - Help keeps remainder of paper stack in place while the top

sheet is picked - Mounts on each side of the separation pad assembly in the paper pickup assembly

(two used)


+49 (0) 3723 / 6678 - 0

Fusing Assembly

3 9

8

1

1

2

5

4

6

1

7

Ref

1

2

3

4

5

6

7

8

9

Part Number

XA9-1421-000CN

XA9-1503-000CN

Description





RM1-2076-030CN Fusing assembly - Bonds toner to paper with heat - For 220V to 240VAC operation -

RA0-1089-000CN

RA0-1104-000CN

RF0-1003-000CN

17 tooth gear - Mounts on the end of the face-up output roller - Center gear of three gears on the

fusing assembly

Roller bushing/retainer - Mounts on the right end of the face-up output roller - Also retains the shaft

in the fusing assembly

Face-up (straight through) output roller - Metal shaft with two rollers - Mounts on the fusing assembly

behind the pressure roller

RM1-0852-000CN Delivery sensor PC board - Small board with optical flag sensor (flag not included) - For sensing paper

output - Mounts on the bottom center of the fusing assembly

RM1-0556-020CN Face-down delivery assembly - Includes the support frame, drive roller and gear, and the four spring

loaded pressure rollers - Mounts in the upper rear of the fusing assembly

RC1-2393-000CN Height flapper - Small plastic ‚L' shaped flapper - Helps to prevent face-down paper output from ba-

cking up into the fusing assembly - Snap-locks onto the face-down output roller in the fusing assembly

Stand: 17.10.2007, Alle Angaben ohne Gewähr.

Scanner Assembly - Including the ADF, and Accociated...

Documents

Transcript of Scanner Assembly - Including the ADF, and Accociated...