Sanitary SORs

ID: AR/iy/Sanitary (Preambles) - FY2011.doc(1)(22.7.10)(May 147-1)

SANITARY, PLUMBING WORKS AND CLEANING,

REPAINTING & STERILIZATION OF WATER TANK

CONTENTS

SECTION DESCRIPTION SOR PAGE

(A) EXCAVATION WORKS 1 (B) CONCRETE WORKS 1 - 2 (C) BRC 2 (D) SCAFFOLDING AND STAGING 2 - 3 (E) MANHOLE 3 - 5 (F) STONEWARE PIPE 5 (G) CAST IRON PIPE AND FITTINGS 5 - 6 (H) DUCTILE IRON PIPE AND FITTINGS 7 - 9 (I) GALVANISED STEEL PIPE AND FITTINGS 9 - 10 (J) UPVC PIPE AND FITTINGS 11 - 20 (K) STAINLESS STEEL PIPE, COPPER PIPE AND FITTINGS 20 - 23 (L) ACCESSORIES FOR PIPE WORK 23 - 24 (M) SANITARY FITTINGS AND ACCESSORIES 25 - 30 (N) BIB TAPS / STOP COCKS / VALVES FOR 31 - 35 SANITARY WORKS (P) TRAP AND GRATING 35 - 39 (Q) MODIFICATION, REPAIRS & SERVICING WORKS 39 - 43 (R) CLEANING AND DESILTING WITH ELECTRO- 43 - 44 MECHANICAL EQUIPMENT (S) WATER TANK REPAIRS, CLEANING & PAINTING WORK 44 - 47 (T) MATERIALS SUPPLY 47 - 48 (U) DAY WORKS 48


SANITARY, PLUMBING WORKS AND CLEANING,

REPAINTING & STERILIZATION OF WATER TANK

SCHEDULE OF RATES

PREAMBLE 1. The rates contained herein include the use of materials, labour, maintenance, supply

of fuel and all idling time of vehicles, opening up, taking down, cutting and refixing, preparation for washing, turning on and off of water supply, tightening bolts and nuts (where necessary), provision of standby plumbers, ladders and torchlights, other tools / equipment and removal of all debris, empty tins and other unwanted materials from the roofs, all as specified, including making good all leaking tank panels with approved sealants (where necessary), conveyance, delivery, unloading, storing, hoisting, stools/ladders, all labour setting, fitting, fixing in position, all cutting and waste, return of packings, establishment charges, overheads, profit and all forms of claim for loss and expense and making good all work disturbed, unless otherwise stated.

2. The rates of painting of water tanks unless otherwise stated include the preparation

of surfaces as per manufacturer’s recommendations and Employer’s instructions. No dilution of coating materials are allowed unless recommended by the manufacturer and the Employer. The application of coating materials shall comply strictly to the manufacturer’s recommendations and Employer’s instructions.

3. The cost of hacking, removal and disposal, and the making good of all affected

works shall be deemed to be included in the Schedule of Rates unless otherwise stated. All schedule of Rates shall be applicable for new and replacement work.

4. Unless otherwise stated, all works shall be measured nett as fixed in its place.

Length of pipes shall be measured based on exposed length. 5. All pipes are described by their respective nominal size specified by the respective

manufacturers. 6. The Employer reserves the right to direct the Contractor to execute any of the

undermentioned items of works which he considers necessary. 7. No scaffold (other than a tower scaffold and trestle scaffold) exceeding 4 metres shall be erected, installed, re-positioned, altered or dismantled except by an approved Scaffold Contractor. An approved Scaffold Contractor shall engage a qualified Scaffolding Supervisor to ensure that the scaffold is erected, installed, re- positioned, altered or dismantled in accordance with the Regulations. The 4 metres height is defined as the distance between the ground level where scaffold rests and the level of the highest working platform. The Schedule of Rates have taken into consideration of the scaffolding cost for height not exceeding 4 metres. The Contractor shall be paid separately for the scaffolding if its height exceeds 4 metres.


PREAMBLE (CONT’D) 8. All brass fittings, valves, cocks & taps shall be of Dezincification Resistant type

unless otherwise stated. 9. The following abbreviations are used for the units:

m - linear metre pr - pair m2 - square metre opg - opening m3 - cubic metre set - set no. - number jt. - joint kg - kilogram test - test job - Per job hr - hour

10. Denotations

* - Computer Code (For Internal Use Only) DZR - Dezincification Resistant C.P. - Chromium Plated W.C. - Water Closet UPVC - Unplasticised Polyvinly Choride CD - Civil Defence

SOR Page 1

SECTION CODE DESCRIPTION UNIT RATE ($)

(A) EXCAVATION WORKS

A 001 Excavate trenches/pits not exceeding 2.0m deep m3 12.80 S A 1

for drain/manhole, part return, fill in and compact,

remainder cart away, deposit on site, spread and

level as directed including provision of planking

and strutting where necessary

A 002 Excavate trench/pit exceeding 2.0m and not m3 14.60 S A 2

exceeding 4.0m deep for drain/manhole part

return, deposit on site, spread fill in and compact,

remainder cart away, and level as directed

including provision of planking and strutting

where necessary

A 003 Cart away surplus excavated material off site m3 4.70 S A 3

and deposit at approved dumping ground

A 004 Services rendered by licensed cable detection Hr 86.25 S A 4

worker for site excavation including preparation of

cable detection report (purchase of drawings shall

be paid separately) (A minimum of 3 hours

shall be paid per job per site)

A 005 Submission to the relevant authority for approval to Job 138.00 S A 5

commence earthworks for excavation around high

tension cable

(B) CONCRETE WORKS

B 001 Breaking up concrete m3 77.10 S B 1

B 002 Break up concrete, part re-use as hardcore, m3 84.40 S B 2

well rammed, levelled and consolidated and

surplus cart away off site including cutting

reinforcement if any

B 003 Cutting through reinforced concrete floor m3 390.40 S B 3

or wall (any thickness) to form opening

* Diamond coring through concrete floor / slab /

column / beam / masonry wall including

detecting locations of reinforcement bar

with re-bar locator for the following measurements

*(004 010)

B 004 50mm - 110mm diameter, 75mm - 175mm depth No. 33.00 S B 4

B 005 50mm - 110mm diameter, 176mm - 275mm depth no. 57.00 S B 5





B 010 Mobilisation of coring equipment for Items No. 300.00 S B 10

B004 to B009

B 011 Concrete Grade 20 in small quantities not exceeding m3 328.00 S B 11

0.15 cubic metre including trowel smooth and

framework

B 012 400mm wide x 100mm thick concrete grade 20 base m 18.80 S B 12

for 100mm diameter drain pipe including haunching

up concrete to sides of pipe of not less than half the

pipe's diameter and necessary formwork

(Excavation & drain pipes measured separately)

EM's CODE

ID : AR/iy/Sanitary (FY11).xls (1) (21.7.10) (May 147-1)

SOR Page 2

SECTION CODE DESCRIPTION UNIT RATE ($) EM's CODE

B 013 450mm wide x 100 mm thick concrete grade 20 base m 20.30 S B 13

for 150mm diameter drain pipe including haunching

up concrete to sides of pipe of not less than half the

pipe's diameter and necessary formwork

(Excavation & drain pipes measured separately)

B 014 Extra over item B012 for concrete grade 20 base of m 13.10 S B 14

150mm thick

B 015 Extra over item B013 for concrete grade 20 base of m 18.90 S B 15

150mm thick

(C) BRC

* BRC or other approved fabric reinforcement laid in

position well lapped at joints *(001 009)

C 001 A6 m2 6.40 S C 1

C 002 A7 m2 8.25 S C 2

C 003 A8 m2 10.80 S C 3

C 004 B6 m2 10.70 S C 4

C 005 B7 m2 12.30 S C 5

C 006 B8 m2 16.20 S C 6

C 007 C6 m2 5.00 S C 7

C 008 C7 m2 6.10 S C 8

C 009 C8 m2 7.40 S C 9

(D) SCAFFOLDING AND STAGING

Fixed Scaffold

D 001 Erect metal scaffolding complying with safety m2 21.00 S D 1

regulations not exceeding 15m in height

including taking down after use.(Measured from

base for which the scaffolding rests)

D 002 Erect metal scaffolding complying with safety m2 23.00 S D 2

regulations exceeding 15m in height including

taking down after use.(Measured from base

for which the scaffolding rests)

D 003 Erect double layer timber scaffolding complying with m2 10.00 S D 3

safety regulations including taking down after use

(height of scaffolding not exceeding 15m high.

A minimum of 5m width shallbe paid)(Measured from

base for which the scaffolding rests)

Mobile Scaffold

D 004 Mobile scaffold compliance with safety Per 115.00 S D 4

regulations and taking down after use job

(the height of the mobile scaffold must

not exceed 3 times its lesser base dimension)

(per job duration)

D 005 Add for item 004 for labour in dismantling, No. 57.50 S D 5

shifting to new location and re-erection


SOR Page 3


Mechanical Suspended Cradles

D 006 Submit drawings and roof plans by Block 400.00 S D 6

Professional Engineer to the relevant

Authorities for approval (building having

similar roof plans/design shall be included

in this rate and shall NOT be paid seperately

under one operation)

D 007 Carry out testing of mechanical suspended Test 230.00 S D 7

cradles by (M&E) Professional Engineer and

obtain approval from the relevant Authoties

D 008 Supply and install mechanical suspended Unit 575.00 S D 8

cradle not exceeding 5 metres length to the

roof including PE endorsement certifing the

proper installation of suspended cradle

according to the PE's design calculations,

drawings and roof plans, application/submission

of electricity supply to various authorities for

approval by licensed electrical worker (hiring

charges and shifting shall be paid separately)

D 009 Hiring charge of approved mechanical Day 60.00 S D 9

suspended cradle not exceeding 5m length

including all accessories, safety precautions

and all necessary shifting of suspended cradles

(E) MANHOLE

Manhole Construction

E 001 225mm thick (average) concrete Grade 20 benching m2 256.10 S E 1

and haunching to bottom of manhole finished with

minimum 13mm thick cement mortar (1:1) rendering,

the whole finished off at a gradient of about one in

six trowelled smooth with coves to 25mm radius at

walls and rounded edges near channels including

working carefully to edge of channels

(Channels measured separately)

E 002 150mm thick concrete Grade 20 top slab reinforced m2 61.40 S E 2

with BRC No C8 reinforcement including formwork

and forming opening for frames

* Half round salt-glazed stoneware straight or curve

branch channels including bedding and jointing in

cement mortar (1:1) of the following size *(003 004)

(Per No. means per channel)

E 003 100mm diameter No. 10.30 S E 3

E 004 150mm diameter No. 13.70 S E 4

E 005 100mm - 150mm diameter half round salt-glazed No. 17.60 S E 5

stoneware taper piece including bedding and

jointing in cement mortar (1:1)

E 006 225mm thick brick works in cement mortar (1:3) for m2 68.90 S E 6

walls of manhole with 20mm thick cement plaster

internally


SOR Page 4


Manhole Cover

E 007 600mm x 600mm triangular heavy duty ductile/cast Pair 354.70 S E 7

iron manhole cover (excluding frame)

E 008 600mm x 600mm medium duty triangular ductile/cast Pair 283.40 S E 8

iron manhole cover (excluding frame)

E 009 600mm x 450mm recessed type galvanised steel No. 92.60 S E 9

manhole cover and frame (finishing on recess is

measured separately)

E 010 300mm x 300mm galvanised steel cover and No. 30.80 S E 10

frame for rain water down pipe's sump

E 011 Cast iron light duty manhole cover and frame Set 71.30 S E 11

with retractable lifting handle including setting

frame in cement mortar (1:3) and sealing cover in

grease and fine sand

E 012 Cast iron light duty manhole cover with retractable No. 65.30 S E 12

lifting handle (excluding frame) and sealing cover in

grease and fine sand

E 013 Cast iron light duty manhole frame only No. 35.80 S E 13

E 014 Lifting handle for cast iron light duty manhole No. 5.70 S E 14

cover

E 015 Cut 2mm wide x 50mm long (maximun) slit at both Job 3.20 S E 15

handle area of existing cast iron manhole cover

E 016 6mm thick aluminium chequered plate m2 1180.00 S D 16

cover including galvanised steel frame work for

grease interceptor

E 017 Hydrostatic test of manhole not exceeding 1.5m deep No. 380.00 S E 17

by Licensed Plumber including liaison and submission

of report / result to PUB

E 018 Hydrostatic test of manhole exceeding 1.5m deep No. 450.00 S E 18

but not ecxeeding 3m deep by licensed

plumber including liaison and submission

of report / result to PUB

* Close Circuit TV (CCTV) inspection of the

internal of drainline in accordance with

PUB (WRN)'s requirements including preparation

and submission of CCTV Inspection Report

to PUB (WRN) complete with supporting videos

and photographs.

Contractor shall flush and clean the drainline

and manhole prior to the CCTV inspection.

Repair of damaged or sunken drainline

shall be measured separately. In the case of

new drain line constructed by the Contractor,

the cost of rectifying the defective drainline

and re-inspection of the drainline by CCTV

shall be borne by the Contractor *(019 020)

E 019 CCTV inspection of main drainline in one Job 1560.00 S E 19

continuous length not exceeding 20m. The CCTV

scan shall commence from one manhole and

ends at another


SOR Page 5


E 020 CCTV inspection for every 10m or part Job 520.00 S E 20

thereof of additional length of drainline

(up to nearest manhole) adjoining the

1st 20m inspected using the CCTV

(F) STONEWARE PIPE

* Salt-glazed stoneware drain pipe in flexible joint

including laying in concrete bed in trench (Trench

and concrete bed measured separately) of the

following diameter *(001 004)

F 001 100mm m 10.60 S F 1

F 002 150mm m 16.70 S F 2

F 003 225mm m 19.00 S F 3

F 004 300mm m 36.90 S F 4

* Salt-glazed stoneware drain pipe for bends

including 150mm thick concrete surround of the


F 005 100mm No. 14.30 S F 5

F 006 150mm No. 21.90 S F 6

F 007 225mm No. 247.50 S F 7

F 008 300mm No. 44.40 S F 8

(G) CAST IRON PIPE AND FITTINGS

Cast Iron Pipe

* Heavy grade coated cast iron drain pipe including

necessary accessories and flexible joints laid in

trench (Trench and concrete bed measured

separately) *(001 004)

G 001 100mm diameter m 32.80 S G 1


G 003 100mm diameter pipe for "duck" foot bend No. 45.00 S G 3

G 004 150mm diameter pipe for "duck" foot bend No. 77.00 S G 4

* Medium grade coated cast iron soil, waste

ventilating and anti-syphonage pipe with socketted

joints caulk with hemp and molten lead and

provision of extra brackets if required *(005 008)






SOR Page 6


Cast Iron Fittings

* Cast iron bend with (any angles) with cleaning

eye caulk with hemp and molten lead *(009 0012)

G 009 50mm diameter No. 9.10 S G 9




* Cast iron equal or unequal tee with cleaning eye

caulk with hemp and molten lead *(013 016)





G 017 75mm to 50mm diameter cast iron reducer No. 18.00 S G 17

G 018 100mm to 75mm diameter cast iron reducer No. 19.00 S G 18

* Short length cast iron pipes with cleaning eye not

exceeding 300mm length *(019 021)




G 022 Steel bolt for cast iron inspection covers No. 0.70 S G 22

* Cast iron cover plate to cleaning eye including all

necessary bolts etc *(023 026)

G 023 50mm diameter pipe and bends No. 4.20 S G 23

G 024 75mm diameter pipes and bends No. 4.80 S G 24



G 027 Cast iron heavy duty 100mm diameter "duck" foot No. 72.10 S G 27

bend including breaking up concrete floor

G 028 100mm diameter cast iron heavy duty union No. 24.50 S G 28

socket for underground pipe

G 029 Cast iron downspout outlet fixed to 75mm diameter No. 14.50 S G 29

cast iron pipe with three numbers of tightening bolts

G 030 225mm x 450mm cast iron purpose made street No. 149.80 S G 30

gully with 100mm outlet including connection, all

necessary excavation and concrete surround.

G 031 110mm diameter cast iron coupling joint including No. 174.10 S G 31

all necessary bolts & nuts


SOR Page 7


(H) DUCTILE IRON PIPE AND FITTINGS

Ductile Iron Pipes

* Ductile iron cement lined heavy duty

water pipes with spigot tylon and socket joints and

brackets/supports including hacking hole through

floors or walls or on roofs (with supports where

necessary) *(001 003)

H 001 80mm m 44.00 S H 1

H 002 100mm m 40.50 S H 2

H 003 150mm m 53.70 S H 3

Ductile Iron Fittings

H 004 80mm socket bends 300mm long including No. 29.70 S H 4

making necessary extra joints (with cleaning eye)

H 005 80mm socket tees including making necessary No. 52.47 S H 5

extra joints

H 006 Extra over item H001, H004 & H005 for bolted flange Joint 9.20 S H 6

joints including all necessary drilling, bolt nut and

gasket

H 007 80mm socket collar No. 32.20 S H 7

H 008 80mm socket and flanged connector / piece No. 47.00 S H 8

H 009 100mm socket bend 300mm long including No. 55.80 S H 9

making necessary extra joints

H 010 100mm socket tees including making necessary No. 50.70 S H 10

extra joints

H 011 Extra over items H002, H009 & H010 for bolted Joint 19.60 S H 11

flange joints including all necessary drilling, bolts

and gaskets

H 012 100mm double flanged "duck" foot bend No. 55.80 S H 12

H 013 100mm double socket long bend No. 60.00 S H 13

H 014 100mm socket collar No. 35.50 S H 14

H 015 100mm iron flanged No. 47.00 S H 15

H 016 100mm flanged spigot piece No. 57.10 S H 16

H 017 100mm flanged tee No. 67.30 S H 17


SOR Page 8


H 018 100mm double flanged lengthening piece No. 50.70 S H 18

not exceeding 300mm long


exceeding 300mm but not exceeding 600mm long



H 021 215mm diameter flange washer for water mains No. 5.30 S H 21

H 022 150mm 45º/22.5º bend No. 56.90 S H 22

H 023 50mm double flanged "duck" foot bend No. 94.30 S H 23

H 024 150mm socket bend 300mm long including No. 65.70 S H 24

making necessary extra joints

H 025 150mm socket tee including making necessary No. 115.40 S H 25

extra joints

H 026 Extra over Item H003, H024 & H025 for bolted Joint 24.30 S H 26

flange joints including all necessary drilling bolts

and gaskets

H 027 Cement lining for 100mm diameter ductile iron fitting No. 8.10 S H 27

H 028 Cement lining for 150mm diameter ductile iron fitting No. 9.40 S H 28

H 029 100mm x 50mm ductile iron cement lined flange tee No. 54.00 S H 29

H 030 50mm blank flange No. 14.50 S H 30



H 033 80mm to 50mm diameter reducer including making No. 36.30 S H 33

necessary extra joints

H 034 100mm to 80mm diameter reducer including making No. 40.90 S H 34

necessary extra joints

H 035 150mm to 100mm diameter reducer No. 63.50 S H 35

pipe including making necessary extra joints

Ductile Iron - Underground Pipe

* Ductile iron cement lined heavy duty pipe

(Push-on Joint 'T' type or mechanical joint 'K' type)

including necessary accessories and flexible joint

laid in trench (Trench and concrete bed measured

separately) *(036 038)

H 036 80mm m 39.80 S H 36

H 037 100mm m 48.80 S H 37

H 038 150mm m 59.60 S H 38


SOR Page 9


H 039 Extra over ductile iron pipe for 80mm elbow (all m 21.50 S H 39

angles)

H 040 Extra over ductile iron pipe for 100mm diameter m 25.20 S H 40

elbow (all angles)

H 041 Extra over ductile iron pipe for 150mm diameter m 48.10 S H 41

elbow (all angles)

H 042 13mm diameter stainless steel bolt, nut and No. 2.20 S D 42

washer for flange joint or other fitting

H 043 Ductile iron flange adaptor for 100mm diameter No. 2.20 S D 43

pipe

UPVC Pipe Cover for Rooftop Water Main

H 044 150mm diameter half channel UPVC pipe (SS213) m 10.00 S H 44

cover to main water distribution pipe at roof top

excluding half channel clip

H 045 150mm diameter UPVC half channel clip No. 9.00 S H 45

H 046 Cable tie for securing half channel UPVC pipe No. 0.30 S H 46

cover to main water distribution main

(I) GALVANISED STEEL PIPE AND FITTINGS

Galvanised Steel Pipes

* UPVC lined galvanised steel water pipe of the

following diameter including cutting off of existing

pipes and accessories, re-threading, all joints and

providing additional holderbats and cutting hole

through walls if necessary. *(001 009)

I 001 15mm m 8.20 S I 1

I 002 20mm m 9.70 S I 2

I 003 25mm m 10.10 S I 3

I 004 32mm m 11.60 S I 4

I 005 40mm m 12.70 S I 5

I 006 50mm m 16.30 S I 6

I 007 65mm m 22.90 S I 7

I 008 75mm m 27.10 S I 8

I 009 100mm m 42.00 S I 9


SOR Page 10


Epoxy Coated Elbow

* Epoxy coated elbow (any angle) for UPVC lined

galvanised steel pipe including jointing of the

following size *(010 014)

I 010 15mm No. 3.90 S I 10

I 011 20mm No. 4.00 S I 11

I 012 25mm No. 4.65 S I 12

I 013 32mm No. 6.70 S I 13

I 014 50mm x 15mm reducing elbow No. 16.00 S I 14

Epoxy Coated Socket

* Epoxy coated socket for UPVC lined galvanised

steel pipe including jointing of the following size

*(015 018)

I 015 15mm No. 4.00 S I 15

I 016 20mm No. 4.20 S I 16

I 017 25mm No. 4.75 S I 17

I 018 32mm No. 5.85 S I 18

Epoxy Coated Nipple

* Epoxy coated nipple for UPVC lined galvanised

steel pipe including jointing of the following

size *(019 023)

I 019 15mm No. 4.30 S I 19

I 020 20mm No. 4.45 S I 20

I 021 25mm No. 4.90 S I 21

I 022 32mm No. 6.15 S I 22

I 023 50mm No. 14.00 S I 23

Epoxy Coated Tee

* Epoxy coated tee for UPVC lined galvanised steel

pipe including of the following size jointing *(024 027)

I 024 15mm Tee No. 4.30 S I 24

I 025 20mm Tee No. 4.45 S I 25

I 026 25mm Tee No. 5.75 S I 26

I 027 32mm Tee No. 8.15 S I 27

I 028 Galvanised flange plate to 100mm diameter No. 17.50 S D 28

galvanised steel pipe including bolt and nut


SOR Page 11


(J) UPVC PIPE AND FITTINGS

Underground Drain Pipes and Fitting

* Approved UPVC drain pipe (SS 272) of the

following diameter with flexible joint laid in trench

(Trench and concrete bed measured separately)

*(001 009)

J 001 100mm m 7.90 S J 1

J 002 150mm m 11.30 S J 2

J 003 200mm m 17.70 S J 3

J 004 100mm bend No. 3.80 S J 4

J 005 150mm bend No. 7.20 S J 5

J 006 200mm bend No. 56.40 S J 6

J 007 100mm Y-junction No. 9.20 S J 7



Soil/Waste Pipe

* Approved UPVC pipe (SS 213/SS 272) of the

following size for rainwater, vent, waste and

soil pipe including jointing and removal of

existing pipe, provision of new saddle clips/

galvanised steel collar brackets where necessary and

hacking of holes through walls or slabs and reinstate

pipe numbering (Fittings and cutting of existing

pipe measured separately) *(010 018)

J 010 32mm (SS 213) m 2.75 S J 10

J 011 40mm (SS 213) m 3.50 S J 11

J 012 50mm (SS 213) m 3.60 S J 12

J 013 80mm (SS 213) m 6.60 S J 13

J 014 100mm (SS 213) m 7.40 S J 14

J 015 150mm (SS 213) m 10.80 S J 15

J 016 200mm (SS 272) m 19.60 S J 16

J 017 200mm x 80mm x 5mm thick rectangular pipe m 39.70 S J 17

(SS 272)

J 018 275mm x 120mm x 5mm thick rectangular pipe m 53.60 S J 18

(SS 272)


SOR Page 12


Sweep Junction (SS213)

* UPVC sweep junction (SS 213) without inspection

opening including jointing of the following diameter

*(019 037)

J 019 32mm No. 2.90 S J 19

J 020 40mm No. 3.60 S J 20

J 021 50mm No. 3.60 S J 21

J 022 80mm No. 5.20 S J 22

J 023 100mm No. 5.20 S J 23

J 024 150mm No. 16.60 S J 24

J 025 80mm to 50mm (SS213) No. 7.40 S J 25

J 026 100mm to 50mm (SS213) No. 5.80 S J 26

J 027 100mm to 80mm (SS213) No. 7.20 S J 27

J 028 150mm to 150mm (SS213) No. 24.10 S J 28

J 029 150mm to 100mm (SS213) No. 10.40 S J 29

J 030 200mm to 50mm (SS 272/213) No. 49.40 S J 30

J 031 200mm to 150mm (SS 272/213) No. 26.20 S J 31

J 032 80mm x 80mm x 50mm double sweep junction No. 9.80 S J 32

(SS213)

J 033 100mm x 100mm x 50mm double sweep No. 10.10 S J 33

junction (SS213)


junction (SS213)


junction (SS213)


junction (SS213)


junction (SS213)


SOR Page 13


Reducing Bush (SS 213)

* UPVC Reducing Bush (SS 213) of the


J 038 100mm to 50mm No. 11.20 S J 38

J 039 100mm to 75mm No. 22.30 S J 39

J 040 80mm to 50mm No. 6.70 S J 40

Socket, Coupling, Connector (SS 213)

* UPVC Socket (SS 213/272) of the following

diameter *(041 047)

J 041 32mm (SS 213) No. 2.90 S J 41

J 042 40mm (SS 213) No. 3.00 S J 42

J 043 50mm (SS 213) No. 3.30 S J 43

J 044 80mm (SS 213) No. 3.30 S J 44

J 045 100mm (SS 213) No. 4.50 S J 45

J 046 150mm (SS 272) No. 6.50 S J 46

J 047 200mm connector piece (SS 272) No. 49.70 S J 47

Bend and Elbow (SS 213)

* UPVC Bend (SS 213) any angles of the following

diameter sizes (Inspection opening including access

cap measured separately) *(048 054)

J 048 32mm No. 2.90 S J 48

J 049 40mm No. 3.00 S J 49

J 050 50mm No. 2.90 S J 50

J 051 80mm No. 4.40 S J 51

J 052 100mm No. 4.50 S J 52

J 053 150mm No. 7.50 S J 53

J 054 120mm x 275mm upvc rectangular elbow (SS 272) No. 157.20 S J 54

plain (Inspection opening including access

cap measured separately)

Reducer (SS 213)

* UPVC Reducer (SS 213) of the following diameter

*(055 061)

J 055 100mm to 50mm reducing bend No. 10.20 S J 55

J 056 100mm to 80mm reducing bend No. 11.30 S J 56

J 057 100mm to 80mm reducer No. 9.00 S J 57


SOR Page 14


J 058 150mm to 100mm reducer No. 14.00 S J 58

J 059 150mm to 100mm level invert reducers No. 8.00 S J 59



UPVC Adaptor (SS 213 / SS 141)

* UPVC Adaptor (SS 213/SS 141) of the


J 062 80mm No. 6.10 S J 62

J 063 100mm No. 6.80 S J 63

J 064 150mm No. 8.40 S J 64

J 065 200mm x 275mm x 120mm No. 141.10 S J 65

UPVC Testing Opening/Access Cap (SS 213)

* Testing openings (F & F) including the access

cap of the following diameter *(066 068)

J 066 80mm Set 11.80 S J 66

J 067 100mm Set 11.30 S J 67

J 068 150mm Set 21.30 S J 68

J 069 Extra over UPVC fitting (various sizes) that comes No. 1.70 S J 69

with inspection opening (cleaning eye) including

access cap

J 070 Form new opening (cleaning eye) on existing UPVC No. 7.80 S J 70

pipe fitting complete with boss connector and access

cap

J 071 Screw-on cover for access opening in UPVC testing No. 4.80 S J 71

opening fitting

UPVC Screw on Socket

UPVC socket (screw on type) for SS213 pipe

*(072 074)

J 072 75mm diameter No. 3.70 S J 72



UPVC Boss Connector (SS 213/272)

J 075 100mm to 50mm diameter boss connector No. 4.80 S J 75

J 076 100mm to 80mm diameter boss connector No. 12.40 S J 76


SOR Page 15


UPVC U-Body & Vent Cowl

J 077 150mm diameter UPVC U-body (SS213) No. 16.70 S J 77

J 078 100mm diameter UPVC U-body (SS213) No. 12.90 S J 78

J 079 100mm diameter UPVC vent cowl to vent pipe No. 2.60 S J 79

J 080 150mm diameter upvc vent cowl to vent pipe No. 5.80 S J 80

* Air Plasma Cutting of Existing Steel / Iron Pipe

Cut existing cast-iron / mild steel / ductile iron

main pipe and all its branches (if any) using

"Air Plasma Cutting System" or other

equivalent method and remove cut section off site

(rate is based on per vertical stack and all its

connecting branches)

*(081 082)

J 081 Not exceeding 100mm diameter No. 18.30 S J 81

J 082 Exceeding 100mm diameter but not exceeding No. 21.90 S J 82

200mm diameter

Cutting of Existing UPVC Pipe

*Cut existing UPVC pipe and all its

branches (if any) by mechanical cutter or

hand tool and remove the cut section off site

(rate is based on per vertical stack and all its

connecting branches)

*(083 085)

J 083 Not exceeding 80mm diameter No. 3.00 S J 83

J 084 Above 80mm diameter but not exceeding 150mm No. 4.20 S J 84

diameter

J 085 Exceeding 150mm diameter No. 5.00 S J 85

Spigot Adaptor (For jointing of cast iron pipe)

* Supply and install of the following UPVC

adaptors (SS 213) including cutting to

the required length and approved sealant

to the interface between the adaptor and

the existing pipe : *(086 095)

J 086 48mm diameter spigot adaptor for 50mm diameter No. 10.80 S J 86

cast iron pipe


cast iron pipe


cast iron vent pipe

J 089 95mm or 96mm diameter spigot adaptor for 100mm No. 19.20 S J 89

diameter cast iron pipe


cast iron 'S' bend

J 091 88mm diameter off-set pan collar No. 18.70 S J 91

J 092 95mm diameter pan collar adaptor for 100mm No. 28.20 S J 92

diameter cast iron pipe


SOR Page 16



cast iron pipe

J 094 95mm diameter grating adaptor for 100mm diameter No. 33.30 S J 94

cast-iron pipe with one/two side inlets irrespective

of size

J 095 117mm diameter grating adaptor for 125mm diameter No. 34.50 S J 95

cast-iron pipe with one/two side inlets irrespective

of size

Rubber Ring Connector

* Supply and install of the following UPVC rubber

ring connectors (SS 213) including applying one

layer of silicone bonding agent to the outside

surface of the protruding cast iron pipe : *(096 102)

J 096 50mm diameter w.c. straight connector with spigot No. 16.80 S J 96














Water Supply Pipes (SS 141)

* UPVC water supply pipes (SS 141) of the

following diameter including cutting, jointing and

removal of existing pipe, provision of new saddle

clip/galvanised collar steel bracket where necessary

and hacking of hole through walls or slabs

(Fitting measured separately) *(103 112)

J 103 15mm m 1.40 S J 103

J 104 20mm m 1.65 S J 104

J 105 25mm m 1.90 S J 105

J 106 32mm m 2.40 S J 106

J 107 40mm m 2.95 S J 107

J 108 50mm m 3.90 S J 108

J 109 65mm m 5.90 S J 109

J 110 75mm m 6.30 S J 110

J 111 100mm m 13.20 S J 111

J 112 150mm m 22.90 S J 112


SOR Page 17


Tee (SS 174)

* UPVC tee (SS 174) including jointing of the


J 113 15mm No. 2.40 S J 113

J 114 20mm No. 2.40 S J 114

J 115 25mm No. 2.50 S J 115

J 116 32mm No. 5.40 S J 116

J 117 40mm No. 6.00 S J 117

J 118 50mm No. 9.60 S J 118

J 119 75mm No. 14.75 S J 119

J 120 20mm x 15mm No. 2.40 S J 120

J 121 25mm x 15mm No. 2.50 S J 121

J 122 40mm x 15mm No. 6.60 S J 122

J 123 40mm x 25mm No. 6.40 S J 123

J 124 50mm x 40mm No. 9.60 S J 124

J 125 65mm x 20mm No. 7.20 S J 125

J 126 75mm x 50mm No. 10.15 S J 126

Socket (SS 174)

* UPVC Socket (SS 174) including jointing of the


J 127 15mm No. 2.25 S J 127

J 128 20mm No. 2.40 S J 128

J 129 25mm No. 2.40 S J 129

J 130 32mm No. 3.70 S J 130

J 131 40mm No. 4.25 S J 131

J 132 50mm No. 5.40 S J 132

J 133 65mm No. 7.00 S J 133

J 134 75mm No. 10.90 S J 134


SOR Page 18


Reducer (SS 174)

* UPVC Reducer (SS 174) including jointing of the


J 135 20mm to 15mm No. 2.40 S J 135

J 136 25mm to 15mm No. 2.40 S J 136

J 137 25mm to 20mm No. 2.50 S J 137

J 138 32mm to 25mm No. 3.20 S J 138

J 139 40mm to 32mm No. 3.90 S J 139

J 140 50mm to 25mm No. 4.40 S J 140

J 141 50mm to 40mm No. 4.70 S J 141

J 142 75mm to 50mm No. 13.00 S J 142

Elbow (SS 174)

* UPVC elbow (any angles) (SS 174) including

jointing of the following diameter *(143 149)

J 143 15mm No. 2.40 S J 143

J 144 20mm No. 2.40 S J 144

J 145 25mm No. 2.40 S J 145

J 146 32mm No. 3.80 S J 146

J 147 40mm No. 5.30 S J 147

J 148 50mm No. 6.70 S J 148

J 149 75mm No. 12.50 S J 149

Valve Socket (SS 174)

* UPVC valve socket (SS 174) including jointing of

the following diameter *(150 157)

J 150 15mm No. 2.25 S J 150

J 151 20mm No. 2.25 S J 151

J 152 25mm No. 2.40 S J 152

J 153 32mm No. 4.00 S J 153

J 154 40mm No. 4.10 S J 154

J 155 50mm No. 4.70 S J 155

J 156 65mm No. 4.50 S J 156

J 157 75mm No. 11.80 S J 157


SOR Page 19


Faucet Socket (SS 174)

* UPVC faucet socket (SS 174) including jointing of


J 158 15mm No. 2.50 S J 158

J 159 20mm No. 2.80 S J 159

J 160 25mm No. 3.30 S J 160

J 161 32mm No. 3.80 S J 161

J 162 40mm No. 4.00 S J 162

J 163 50mm No. 5.20 S J 163

Faucet Elbow (SS 174)

* UPVC faucet elbow (SS 174) including jointing of


J 164 15mm No. 2.83 S J 164

J 165 15mm (with wall plate) No. 2.60 S J 165

J 166 20mm No. 3.20 S J 166

J 167 25mm No. 4.10 S J 167

J 168 40mm No. 5.90 S J 168

Simple Joint (SS 174)

* UPVC simple joint (SS 174) including jointing of


J 169 15mm No. 2.25 S J 169

J 170 22mm No. 2.60 S J 170

J 171 28mm No. 2.70 S J 171

J 172 35mm No. 9.80 S J 172

J 173 40mm No. 9.10 S J 173

J 174 50mm No. 11.50 S J 174

End Cap (SS 174)

* UPVC end cap (SS 174) including jointing of the


J 175 15mm No. 2.25 S J 175

J 176 20mm No. 2.50 S J 176

J 177 25mm No. 2.60 S J 177

J 178 32mm No. 3.30 S J 178

J 179 40mm No. 3.40 S J 179


SOR Page 20


J 180 50mm No. 3.90 S J 180

J 181 65mm No. 4.40 S J 181

J 182 75mm No. 8.50 S J 182

Adaptor (SS 174)

* UPVC adaptor (SS 174) of the following

diameter *(183 185)

J 183 80mm No. 6.85 S J 183

J 184 100mm No. 7.15 S J 184

J 185 150mm No. 7.90 S J 185

(K) STAINLESS STEEL PIPES, COPPER PIPES

AND FITTINGS

Stainless Steel Pipes

* Stainless steel pipe to B.S.4127 including holderbat

or clip and cutting of old pipe (fittings measured

separately) of the following diameter (outside

diameter) *(001 006)

K 001 15mm m 7.70 S K 1

K 002 22mm m 8.50 S K 2

K 003 28mm m 10.20 S K 3

K 004 35mm m 12.30 S K 4

K 005 42mm m 14.15 S K 5

K 006 54mm m 17.70 S K 6

Copper Pipe

* Copper pipes including holderbat or clip and cutting

of old pipe (fittings measured separately) of the


K 007 13mm m 8.20 S K 7

K 008 20mm m 9.80 S K 8

K 009 25mm m 11.70 S K 9

K 010 40mm m 21.30 S K 10

K 011 50mm m 23.90 S K 11

Brass Elbow

* Brass elbow (DZR type, any angle) for copper/

stainless steel pipes of the following

diameter *(012 018)

K 012 15mm No. 4.10 S K 12

K 013 15mm Faucet No. 3.45 S K 13

K 014 22mm No. 4.80 S K 14


SOR Page 21


K 015 28mm No. 5.80 S K 15

K 016 35mm No. 10.00 S K 16

K 017 42mm No. 13.10 S K 17

K 018 54mm No. 19.80 S K 18

Brass Coupling

* Brass coupling (DZR type) for copper/stainless

steel pipe of the following diameter *(019 030)

K 019 15mm No. 3.45 S K 19

K 020 22mm No. 4.40 S K 20

K 021 28mm No. 5.90 S K 21

K 022 35mm No. 8.90 S K 22

K 023 42mm No. 11.60 S K 23

K 024 54mm No. 14.60 S K 24

K 025 42mm x 54mm (reducing) No. 14.80 S K 25






Brass Tee

* Brass tee (DZR type) for copper/stainless steel

pipe of the following diameter *(031 052)

K 031 15mm x 15mm x 15mm No. 4.30 S K 31

K 032 15mm x 22mm x 15mm No. 5.30 S K 32

K 033 22mm x 22mm x 22mm No. 5.40 S K 33

K 034 22mm x 22mm x 15mm No. 5.30 S K 34

K 035 28mm x 28mm x 28mm No. 7.40 S K 35

K 036 28mm x 28mm x 22mm No. 9.20 S K 36

K 037 28mm x 28mm x 15mm No. 7.80 S K 37

K 038 28mm x 35mm x 28mm No. 13.25 S K 38

K 039 35mm x 35mm x 35mm No. 13.50 S K 39

K 040 35mm x 35mm x 28mm No. 12.90 S K 40

K 041 35mm x 35mm x 22mm No. 12.90 S K 41

K 042 35mm x 35mm x 15mm No. 12.90 S K 42


SOR Page 22


K 043 42mm x 42mm x 42mm No. 21.00 S K 43

K 044 42mm x 42mm x 35mm No. 18.00 S K 44

K 045 42mm x 42mm x 28mm No. 17.10 S K 45

K 046 42mm x 42mm x 22mm No. 19.00 S K 46

K 047 42mm x 42mm x 15mm No. 23.20 S K 47

K 048 54mm x 54mm x 54mm No. 27.10 S K 48

K 049 54mm x 54mm x 42mm No. 26.60 S K 49

K 050 54mm x 54mm x 35mm No. 27.10 S K 50

K 051 54mm x 54mm x 28mm No. 26.00 S K 51

K 052 54mm x 54mm x 15mm No. 36.50 S K 52

Brass Reducing Elbow

* Brass reducing elbow (DZR type, any angle) for

copper/stainless steel pipe of the following

diameter *(053 065)

K 053 22mm x 13mm No. 5.50 S K 53

K 054 22mm x 15mm No. 4.60 S K 54

K 055 28mm x 22mm No. 6.20 S K 55

K 056 28mm x 15mm No. 6.00 S K 56

K 057 35mm x 22mm No. 9.70 S K 57

K 058 54mm x 15mm No. 20.40 S K 58

K 059 54mm x 28mm No. 23.40 S K 59

K 060 35mm x 28mm No. 10.10 S K 60

K 061 54mm x 35mm No. 21.30 S K 61

K 062 54mm x 42mm No. 21.70 S K 62

K 063 42mm x 28mm No. 14.30 S K 63

K 064 35mm x 15mm No. 9.20 S K 64

K 065 42mm x 15mm No. 13.90 S K 65

Brass Stop End

* Brass stop end (DZR type) for copper/stainless


K 066 42mm No. 15.00 S K 66

K 067 54mm No. 22.30 S K 67


SOR Page 23


Brass Nipple

* Brass nipple (DZR type) for copper/stainless


K 068 13mm diameter brass nipple No. 2.50 S K 68

K 069 54mm diameter brass nipple No. 8.40 S K 69

Coupling Ring

* Coupling ring of the following

diameter *(070 076)

K 070 13mm No. 0.80 S K 70

K 071 20mm No. 1.20 S K 71

K 072 30mm No. 1.20 S K 72

K 073 40mm No. 1.60 S K 73

K 074 50mm No. 1.90 S K 74

K 075 75mm No. 2.10 S K 75

K 076 100mm No. 2.60 S K 76

(L) ACCESSORIES FOR PIPEWORK

Hanger

L 001 Purpose made 32mm wide x 4mm thick mild No. 15.40 S L 1

steel hanger for pipe not exceeding 100mm

diameter including anchoring to structure using

approved expansion bolt

L 002 Purpose made 32mm wide x 4mm thick mild No. 18.60 S L 2

steel hanger for pipe exceeding 100mm diamter

but not exceeding 200mm diameter including

anchoring to structure using approved

explosion bolt

L 003 15mm to 20mm wide punched steel pipe hanger No. 5.20 S L 3

including anchoring to structure using approved

expansion bolt (Band not exceeding 1.5 metre long)

Steel Collar Bracket

* Standard hot-dipped galvanised steel collar

bracket for UPVC soil/waste pipe of the following

diameter *(004 006)

L 004 80mm No. 5.30 S L 4

L 005 100mm No. 5.40 S L 5

L 006 150mm No. 5.60 S L 6

* Hot-dipped galvanised steel collar bracket with

neoprane rubber lining and screw-on wall anchor

for UPVC soil/waste pipes of the following

diameter *(007 009)

L 007 80mm No. 8.70 S L 7

L 008 100mm No. 9.80 S L 8

L 009 150mm No. 10.70 S L 9


SOR Page 24


Galvanised Steel Pipe Clip

L 010 Galvanised steel holderbats or clips for water pipes No. 1.50 S L 10

not exceeding 25mm diameter

L 011 Galvanised steel holderbats or clips for water pipes No. 2.40 S L 11

exceeding 28mm but not exceeding 54mm diameter

L 012 Galvanised steel holderbats or clips for No. 4.10 S L 12

water pipes exceeding 54mm diameter

UPVC Pipe Clip

* UPVC pipe clip of the following diameter *(013 018)

L 013 16mm No. 0.80 S L 13

L 014 22mm No. 0.90 S L 14

L 015 28mm No. 0.90 S L 15

L 016 36mm No. 1.20 S L 16

L 017 42mm No. 1.30 S L 17

L 018 54mm No. 1.40 S L 18

Clamp for Stainless Steel Pipe/Ductile Iron Pipe

* Stainless steel pipe clamp with rubber lining and

compression bolt for emergency rectification of

pipe burst of the following pipe

diameter *(019 023)

L 019 Not exceeding 40mm diameter No. 34.00 S L 19

L 020 More than 40mm diameter but not exceeding No. 79.20 S L 20

50mm diameter


80mm diameter

L 022 More than 80mm diamter but not exceeding No. 171.60 S L 22

100mm diameter


150mm diameter

L 024 Mild steel compression bracket comprising two No. 19.80 S L 24

100mm diameter x 40mm wide x 5mm thick rings

and two 10mm diameter threaded rods not

exceeding 300mm long including painting


SOR Page 25


(M) SANITARY FITTINGS AND ACCESSORIES

Fireclay Sink

* White fireclay sink (Saniton, Claytan or other

approved) complete with cantilever brackets, 40mm

vulcanite plug and chain, all necessary trap, waste

pipe and flexible tube of the following size *(001 004)

M 001 600mm x 450mm x 200mm No. 123.20 S M 1

M 002 685mm x 450mm x 250mm No. 144.50 S M 2

M 003 600mm x 450mm x 200mm (without cantilever No. 106.20 S M 3

bracket)

M 004 685mm x 450mm x 250mm (without cantilever No. 126.30 S M 4

bracket)

Wash Hand Basin

* Vitreous china wash hand basin (Saniton, Claytan

or other approved) complete with cantilever brackets,


pipe, miniature stop valve and flexible tube of the

following sizes *(005 010)

M 005 500mm x 400mm (white) No. 80.20 S M 5

M 006 500mm x 400mm (coloured) No. 112.80 S M 6

M 007 500mm x 400mm (coloured with pedestal stand) No. 167.40 S M 7

M 008 500mm x 400mm (white) with delay action pillar No. 151.10 S M 8

tap in lieu of push button spring type

M 009 500mm x 400mm (coloured) with delay action pillar No. 160.70 S M 9

tap in lieu of push button spring type

M 010 500mm x 400mm (coloured with pedestal stand) No. 215.40 S M 10

with delay action pillar tap in-lieu of push button

spring type

M 011 Integral coloured cultured marble basin and top of No. 544.40 S M 11

approximate size 525 x 1500mm with backsplash,

200mm front apron complete with integrated basin,

approved single lever mixer tap with pop-up waste,

bottle trap, waste pipe and galvanised steel bracket

for fixing to wall, and all necessary accessories for

fixing and jointing to pipework miniature stop valve

with flexible tube

M 012 550mm x 450mm stainless steel wash hand basin No. 63.10 S M 12

complete with pillar tap, cantilever brackets,


pipe miniature stop valve and flexible tube

Sink

M 013 1000mm x 500mm single bowl single drainer 2.03mm No. 66.00 S M 13

thick anodised aluminium sink complete with

cantilever brackets 40mm vulcanite plug and chain,

all necessary trap, waste pipe miniature stop valve

and flexible tube


SOR Page 26


M 014 1500mm x 500mm single bowl double drainer No. 157.08 S M 14

2.03mm thick anodised aluminium sink complete

with cantilever brackets 40mm vulcanite plug and

chain, all necessary trap, waste pipe miniature stop

valve and flexible tube

M 015 1067mm x 457mm single bowl, single drainer No. 66.00 S M 15

stainless steel sink complete with cantilever brackets

40mm vulcanite plug and chain, all necessary trap,

waste pipe miniature stop valve and flexible tube

M 016 1500mm x 500mm locally made single bowl double No. 200.90 S M 16

drainer stainless steel sink complete with

cantilever brackets 40mm vulcanite plug and chain,

all necessary trap, waste pipe miniature stop valve

and flexible tube

M 017 1500mm x 500mm locally made double bowl single No. 223.20 S M 17

drainer stainless steel sink complete with cantilever

brackets 40mm vulcanite plug and chain, all

necessary trap, waste pipe miniature stop valve

and flexible tube

W.C. Suite/Pan (Saniton, Claytan or other approved)

M 018 Close-coupled white vitreous china wash-down No. 311.00 S M 18

pedestal w.c. suite complete with approved rigid

(heavy duty) plastic seat and cover with buffers and

hinging devices, white vitreous china 9.0/4.5 litres

dual action flushing cistern and all necessary fittings

and connections to pipework

M 019 Close-coupled coloured vitreous china wash-down No. 377.00 S M 19

pedestal w.c. suite complete with approved rigid





M 020 White-vitreous china close-coupled single-trap No. 344.20 S M 20

syphonic w.c. suite complete with approved rigid





M 021 Close-coupled white vitreous china wash down No. 173.30 S M 21

pedestal w.c. pan only, complete with plastic seat

and cover with buffers and hinging devices including

trap with or without vent

M 022 White earthenware squat w.c. pan only, complete No. 146.30 S M 22

with trap and with/without vent including making good

tile surround to match if necessary and hacked up

existing damage pan

M 023 White earthenware pedestal w.c. pan only, complete No. 231.00 S M 23

with plastic seat and trap with or without vent

Urinal (Saniton, Claytan or other approved)

M 024 White vitreous China urinal bowl No. 206.60 S M 24

M 025 White vitreous China wall hung urinal bowl No. 114.80 S M 25


SOR Page 27


M 026 White glazed urinal slabs 600mm wide x 1050mm No. 551.30 S M 26

high

M 027 White glazed urinal return end slab 1050mm high to No. 245.00 S M 27

match existing

M 028 100mm semi-circular white glazed urinal floor m 159.10 S M 28

channels to match existing including bedding in

cement mortar (1:3) and pointing in white cement

M 029 150mm semi-circular white glazed urinal floor m 168.96 S M 29

channels to match existing incuding bedding in

cement mortar (1:3) and pointing in white cement

M 030 Glazed modesty board in between wall hung No. 122.80 S M 30

urinal bowl including fixing accessories

Cistern

M 031 9/4.5 litres dual action approved high level plastic No. 45.50 S M 31

cistern complete with nylon cord, plastic pull and

brackets

M 032 9/4.5 litres dual action approved low level plastic No. 45.50 S M 32

cistern complete with flush bend, actuating lever

handle and cantilever brackets

Accessories for Basin / Sink

M 033 UPVC pipe, for sink waste including elbow and bend No. 11.00 S M 33

M 034 Vulcanite plug complete with chain for sink or basin No. 3.30 S M 34

M 035 5mm diameter x 75mm long brass grid screw to No. 1.20 S M 35

sink.

M 036 Brass waste fitting to sink or basin complete with Set 6.90 S M 36

brass cobweb grating, chain and plug

M 037 Brass waste fitting to sink or basin complete with No. 4.80 S M 37

brass cobweb grating only.

M 038 15mm Basin mixer lift-up tap No. 62.50 S M 38

M 039 15mm Sink mixer lift-up tap with swivel spout No. 57.50 S M 39

M 040 `Presto' No. 605 or other approved wash basin delay No. 89.70 S M 40

action pillar tap.

M 041 Cast iron brackets for draining board, sink, basin or No. 6.20 S M 41

cistern including cutting and fixing to walls

Accessories for WC Suite/Pan

M 042 PVC screw cap for vent of w.c. squat/pedestal pan No. 2.80 S M 42

M 043 Plastic w.c. seat complete with cover. (Heavy duty No. 26.40 S M 43

of any colour)

M 044 Plastic w.c. seat but without cover. (Heavy duty No. 9.90 S M 44

of any colour)


SOR Page 28


M 045 Rubber cone for joint between flush pipe and back No. 3.30 S M 45

inlet of w.c. pedestal pan.

M 046 100mm diameter PVC w.c. pan collar/offset No. 7.50 S M 46

M 047 Porcelain enamelled foot treads for squat pan Pair 33.60 S M 47

including hacking up existing and make good tile

surround if necessary to match existing

Accessories for Urinal

M 048 75mm brass cobweb grating to urinal. No. 4.90 S M 48

M 049 `Presto' No 12 or other approval Urinal delay action No. 89.70 S M 49

tap

Sparge Pipe

M 050 15mm diameter copper sparge pipes with brackets m 13.70 S M 50

to match existing including additional holders and all

accessories.

M 051 22mm diameter copper sparge pipes with brackets m 16.40 S M 51

to match existing including additional holders and all

accessories.

M 052 15mm diameter galvanised steel sparge pipe with m 6.40 S M 52

brackets to match existing including plainting and

additional holders.

M 053 20mm diameter galvanised steel sparge pipe with m 7.10 S M 53

brackets to match existing including plainting and

additional holders.

Accessories for Cistern

M 054 Glazed vitreous clay lid cover to w.c. cistern No. 10.20 S M 54

M 055 Plastic lid cover to w.c. cistern No. 4.90 S M 55

M 056 Brass flush arm to high level cistern. No. 9.70 S M 56

M 057 Brass chain and rubber pull for high level cistern No. 6.90 S M 57

M 058 Brass ball-cock to w.c. custern. No. 10.50 S M 58

M 059 Brass nut for flush pipe to w.c. cistern outlet No. 5.40 S M 59

connection .

M 060 Chromium plated lever handle to low level w.c. No. 5.30 S M 60

cistern.

M 061 Chromium plated flush button for wc cistern No. 9.10 S M 61

M 062 Plastic syphon unit to high level cistern. No. 13.20 S M 62

M 063 Plastic syphon unit to low level cistern. No. 21.00 S M 63

M 064 Plastic flush arm to w.c. cistern. No. 3.20 S M 64

M 065 Plastic flush arm holder with nylon rope to w.c. No. 3.10 S M 65

cistern.


SOR Page 29


M 066 Plastic ball-with valve to w.c. cistern No. 8.40 S M 66

M 067 Plastic nut for flush pipe to w.c. cistern outlet No. 4.20 S M 67

connection

M 068 PVC flush pipe not exceeding 2.0m long bend to No. 5.30 S M 68

high level cistern

M 069 PVC flush pipe exceeding 2.0m but not exceeding No. 6.30 S M 69

3.0m long bent to high level cistern

M 070 40mm PVC flush pipe to low level cistern No. 4.20 S M 70

M 071 Rubber washer to w.c. cistern syphon plunger No. 5.50 S M 71

including dismantling and refixing unit

M 072 13mm diameter ball valve in w.c. cistern No. 7.50 S M 72

M 073 25mm diameter ball valve in w.c. cistern No. 13.70 S M 73

M 074 Galvanised syphon hook No. 1.90 S M 74

M 075 Galvanised steel cistern chain and pull for No. 6.20 S M 75

high level cistern

Flexible Inlet Tube

*Light gauge 13mm diameter flexible inlet tube

to cisterns/basins and taps complete with

connector *(076 078)

M 076 Not exceeding 300mm long No. 3.80 S M 76

M 077 More than 300mm long but not exceeding No. 4.50 S M 77

600mm long

M 078 Exceeding 600mm long No. 6.00 S M 78

Toilet Roll Holder/Dispenser

M 079 Jumbo plastic toilet roll dispenser No. 25.80 S M 79

M 080 Surfaced mounted chromium plated toilet roll holder No. 12.50 S M 80

with plastic roller fixed or plugged to wall

M 081 Surfaced mounted plastic type toilet roll holder with No. 8.90 S M 81

plastic roller fixed or plugged to wall

M 082 Approved plastic roller fixed in existing toilet roll No. 0.70 S M 82

holder brackets

Soap Tray/Dispenser

M 083 150 x 150mm white glazed recessed type soap tray No. 14.90 S M 83

embedded in cement mortar including hacking off

existing and make good tile surround to match

M 084 108mm x 108mm white glazed recessed type soap No. 16.90 S M 84

tray embedded in cement mortar

M 085 20G 18-8 Type 304 stainless steel rectangular liquid No. 43.80 S M 85

soap dispenser or other approve of 1.2 litre capacity

equipped with acrylic soap level window, exposed

surface stain-finished complete with vandal resistant

mounting bracket and separate concealed wallplate

M 086 Horizontal all purposed valve (Model CV-025A) for No. 9.90 S M 86

stainless steel liquid soap dispenser constructed of

chrome plated brass with Buna-N "O" ring markings

with engineering plastic moving parts and push-in

type valve projecting 61mm


SOR Page 30


M 087 Plastic soap dispenser. No. 10.00 S M 87

M 088 Deck mounted stainless steel liquid soap dispenser No. 47.80 S M 88

Mirror

M 089 Approve 6mm thick lavatory mirror including matching m2 68.60 S M 89

screws and aluminium frame

Shower Rose

M 090 Mixer tap for showerhead No. 67.60 S M 90

M 091 Chromium plated copper shower rose. No. 6.50 S M 91

M 092 Chromium plated spray shower with chromium No. 15.90 S M 92

plated flexible tubing brackets and sliding rail

M 093 Standard ABS chrome plated shower set comprising Set 115.00 S M 93

shower head (minimum 2 spray patterns),

wall mounted sliding rail, height adjustable and

rotatable shower head holder and soap dish and

minimum 1.5m long flexible connecting tube

Long Bath Trap

M 094 Long bath trap complete with waste fittings and No. 11.40 S M 94

overflow pipes

M 095 Long bath mixer No. 176.60 S M 95

Temporary Removal of WC/LongBath

M 096 Temporary removal of Vitreous china pedestal to No. 45.00 S M 96

facilitate repair works and re-installation of existing

pedestal upon completion of repair works including

repositioning of flushing cistern if necessary

repositioning of flushing cistern (measured

separately if such job is required)

M 097 Temporary removal of long bath tub to facilitate repair No. 91.30 S M 97

works and re-install the existing long bath tub upon

completion of repair works including all necessary

reinstatement of wall tiles, pipings and fittings

(reinstatement of wall tiles and pipe fittings measured

separately)

Hand Dryer

M 098 Electric automatic hand dryer No. 210.60 S M 98

Stainless Steel Screen

M 099 150mm square or round x 1.16mm thick stainless No. 60.00 S M 99

steel screen with 13mm diameter perforated holes to

outlet of water main at rooftop water tanks

Bin Chute Flush Pipe

M 100 25mm diameter C.P. copper flush pipes including all No. 13.70 S M 100

necessary tees and brackets for each chute

M 101 25mm diameter galvanised steel flush pipe including No. 11.00 S M 101

all necessary tees and brackets for each chute


SOR Page 31


(N) BIB TAPS / STOP COCKS / VALVES FOR

SANITARY WORKS

Stop Cock

Brass stop cock of the following

size *(001 006)

N 001 13mm No. 12.10 S N 1

N 002 20mm No. 18.75 S N 2

N 003 25mm No. 31.50 S N 3

N 004 32mm No. 78.10 S N 4

N 005 40mm No. 95.30 S N 5

N 006 50mm No. 184.00 S N 6

N 007 13mm chromium plated brass stop cock No. 13.00 S N 7

Bib Tap

N 008 13mm brass bin tap No. 10.20 S N 8

N 009 15mm brass bib tap No. 12.00 S N 9

N 010 20mm brass bib tap No. 14.40 S N 10

N 011 13mm brass bib tap with spigot nozzle including No. 10.50 S N 11

detachable tap head

N 012 13mm brass bib tap with a hole drilled through No. 11.00 S N 12

the shaft for the tap head for locking purpose

N 013 13mm brass bib tap with spigot nozzle and No. 12.50 S N 13

a hole drilled through the shaft for the tap

head for locking purpose

N 014 13mm brass 2-way bib tap No. 12.00 S N 14

N 015 13mm chromium plated brass bib tap No. 10.00 S N 15

N 016 15mm chromium plated brass bib tap No. 15.00 S N 16

N 017 13mm chromium plated brass 2-way bib tap No/ 18.00 S N 17

N 018 15mm chromium plated brass 2-way bib tap No. 24.00 S N 18

(lever head type)

N 019 15mm chromium plated brass 2-way bib-tap No. 24.00 S N 19

N 020 15mm chromium plated brass 2-way bib-tap No. 28.00 S N 20

(lever head type)

N 021 13mm chromium plated long handle tap No. 47.80 S N 21

Garden Bib Tap

N 022 13mm matt steel finish garden bib tap with No. 11.40 S N 22

spigot nozzle and lever head

N 023 15mm matt steel finish garden bib tap with No. 21.10 S N 23

spigot nozzle and lever head

Pillar Tap

N 024 13mm brass pillar tap No. 11.50 S N 24

N 025 15mm brass pillar tap No. 13.00 S N 25

N 026 13mm chromium plated brass pillar tap No. 14.90 S N 26


SOR Page 32


N 027 15mm chromium plated brass pillar tap No. 17.00 S N 27

N 028 15mm chromium plated pillar tap with swivel No. 21.70 S N 28

swan neck

N 029 20mm chromium plated brass pillar tap for No. 32.00 S N 29

long bath

N 030 13mm chromium plated magnetic controlled No. 23.00 S N 30

spindle tap with spigot nozzle (Detachable

magnetic turn head to be paid separately)

N 031 Magnetic turn head for magnetic controlled No. 5.10 S N 31

spindle tap

Gland Nut

* Gland nut of the following size *(032 037)

N 032 13mm No. 2.80 S N 32

N 033 20mm No. 2.80 S N 33

N 034 25mm No. 2.90 S N 34

N 035 32mm No. 2.90 S N 35

N 036 40mm No. 3.20 S N 36

N 037 50mm No. 3.60 S N 37

Rubber Washer

N 038 Rubber washer for 13mm to 25mm stop cock or bib No. 1.10 S N 38

tap in replacement.

N 039 Rubber washer for 30mm to 50mm stop cock or bib No. 1.40 S N 39

tap in replacement.

Gate Valve

* Bronze gate valve of the following diameter in

replacement including washers, gaskets, bolts and

nuts. *(040 047)

N 040 13mm No. 8.90 S N 40

N 041 20mm No. 11.40 S N 41

N 042 25mm No. 14.80 S N 42

N 043 30mm No. 21.10 S N 43

N 044 40mm No. 27.40 S N 44

N 045 50mm No. 35.70 S N 45

N 046 75mm No. 105.30 S N 46

N 047 100mm No. 209.40 S N 47

N 048 80mm diameter ductile/cast iron gate valve including No. 133.40 S N 48

washers, gaskets, bolts and nuts

N 049 100mm diameter ductile/cast iron gate valve including No. 164.50 S N 49

washers, gaskets, bolts and nuts

N 050 50mm diameter DZR type brass gate valve including No. 33.10 S N 50

washers, gaskets, bolts & nuts, etc


SOR Page 33


Ball Valve

N 051 40mm diameter DZR type brass ball valve No. 33.20 S N 51

N 052 Lever stem to 50mm diameter equilibrium ball float No. 13.50 S N 52

valve

Sluice Valve

N 053 150mm diameter cast iron sluice valve with flanged No. 261.70 S N 53

ends and wheel head

Pressure Reducing Valve

* Bronze body pressure reducing valve, female ends

with rubber diaphragm of the following

diameter *(054 056)

N 054 32mm No. 145.70 S N 54

N 055 40mm No. 180.20 S N 55

N 056 50mm No. 237.70 S N 56

* Gunmetal body pressure reducing valve, female

ends with rubber diaphragm of the following

diameter *(057 059)

N 057 32mm No. 352.70 S N 57

N 058 40mm No. 410.20 S N 58

N 059 50mm No. 582.70 S N 59

W.C. Flush Valve

N 060 Exposed water closet flush valve with 240mm x No. 177.70 S N 60

408mm `L' flush pipe, vacuum breaker and stop

valve for back inlet water closet

N 061 Exposed water closet flush valve with 280mm long No. 177.70 S N 61

supply pipe, vacuum breaker and stop valve for top

inlet water closet bowl

N 062 Water closet water-saving flush valve with 470mm x No. 184.70 S N 62

320mm long `T' flush pipe, vacuum breaker and stop

value

N 063 Water closet water-saving flush valve with 280mm No. 186.80 S N 63

long flush pipe, vacuum breaker and stop valve

N 064 Water closet concealed flush valve with flushing pipe No. 93.00 S N 64

and 32mm diameter elbow coupling

N 065 Water closet water-saving concealed flush valve with No. 220.00 S N 65

flushing pipe and 32mm diameter elbow coupling

N 066 PUB approved stainless steel sensor operated flush No. 512.00 S N 66

valve complete with stainless steel outlet flush

pipes to water closets including fixing and jointing

to water supply and fittings as specified

Urinal Flush Valve

N 067 `Presto' No 12A or other approved concealed Urinal No. 103.50 S N 67

flush valve for public toilets

N 068 Urinal flush valve with/without spud No. 51.20 S N 68

N 069 Urinal concealed flush valve with 16mm diameter `L' No. 99.90 S N 69

shape flushing pipe, front cap cover, but without spud

N 070 Urinal concealed flush valve with 16mm diameter `L' No. 111.00 S N 70

shape flushing pipe, front cap cover, but with spud


SOR Page 34


N 071 PUB approved stainless steel sensor operated flush No. 302.00 S N 71

valve complete with stainless steel outlet flush pipes

to urinals including fixing and jointing to water

supply and fittings as specified

N 072 Repair automatic (electronic) sensor for flush valve Job 16.00 S N 72

(Parts measured separately)

Electronic Sensor Parts for WC/Urinal

Auto-Flush Valve

N 073 Flush valve assembly (Body, 'O' ring, Adaptor No. 20.30 S N 73

and Handle cap)

N 074 Flush valve cap No. 9.50 S N 74

N 075 Flush valve body No. 14.90 S N 75

N 076 Flush valve cap rubber washer No. 4.70 S N 76

N 077 Flush valve adaptor No. 6.50 S N 77

N 078 Flush valve 'O' ring No. 3.25 S N 78

N 079 Stopcock assembly complete with handle, 'O' ring No. 44.60 S N 79

stopcock cap, 'O' ring, seal check valve and rubber

washer

N 080 Stopcock handle No. 9.80 S N 80

N 081 Stop cock cap No. 4.70 S N 81

N 082 Stopcock cap 'O' ring No. 3.25 S N 82

N 083 Stopcock seal No. 4.60 S N 83

N 084 Stop valve rubber washer No. 3.25 S N 84

N 085 Push Button assembly complete with cap nut, No. 12.20 S N 85

hexagonal nut and switch

N 086 Solenoid assembly complete with valve, coil, plug, No. 28.30 S N 86

rubber washer and screws (E-Ring)

N 087 Solenoid bracket complete with screws No. 11.50 S N 87

N 088 Sensor assembly complete with studs and nuts No. 34.40 S N 88

N 089 Sensor plate and pivot rod No. 13.70 S N 89

N 090 Vacuum breaker assembly complete with rubber No. 20.30 S N 90

washer, outlet piping rubber washer and outlet piping

nut

N 091 Vacuum breaker rubber washer No. 3.25 S N 91

N 092 Hydraulic bypass valve No. 14.40 S N 92

N 093 Check valve No. 11.90 S N 93

N 094 Check valve rubber washer No. 3.25 S N 94

N 095 Outlets piping rubber washer No. 3.25 S N 95

N 096 Adaptor rubber washer No. 3.25 S N 96

N 097 Piston No. 11.50 S N 97

N 098 Casing complete with front cover, back cover and No. 23.30 S N 98

screws


SOR Page 35


N 099 Cover frame complete with screws (and magnet) No. 17.30 S N 99

N 100 Cam lock for sensor plate No. 6.50 S N 100

N 101 AC Adaptor with controller board assembly No. 27.00 S N 101

complete with earth wire, connector and screws

N 102 Micro switch No. 3.60 S N 102

N 103 Battery pack for battery-operated sensor No. 21.00 S N 103

N 104 Elbow adaptor (90 degree straight, T-Elbow) No. 4.70 S N 104

N 105 Elbow M4 male stud tubing fitting No. 4.70 S N 105

N 106 4mm to 6mm PU tubing m 1.80 S N 106

N 107 Outlet piping nut No. 3.25 S N 107

Stop Valve for Basin/Cistern

N 108 Miniature stop valves for basin and cistern No. 4.70 S N 108

Flow Regulator

N 109 15mm diameter approved constant flow regulator of No. 5.60 S N 109

12 litres per minute

Rubber Hose

N 110 19mm non-kink, 2 braided rubber hose m 7.50 S N 110

N 111 25mm non-kink, 2 braided rubber hose m 7.50 S N 111

(P) TRAP AND GRATING

Floor Trap

P 001 150mm salt-glazed stoneware gulley complete with No. 58.30 S P 1

upvc grating, 100mm outgo and 100mm thick

concrete surround including hacking existing

damaged gulley and jointing to existing pipes

P 002 Cast iron deep seal floor trap complete with hinged No. 85.30 S P 2

grating cast iron hopper and with vertical side or

back inlets and 75mm outgo pipe including hacking

existing damaged trap and jointing to existing pipe

P 003 150mm cast iron hopper connecting piece not No. 13.20 S P 3

exceeding 300mm long including hacking existing

hopper and all necessary jointing

P 004 100mm diameter cast iron floor trap or floor waste No. 59.60 S P 4

with hinged grating, hopper and 75mm outgo and

concrete surround (at ground floor slab) including

hacking to remove existing damaged trap/waste and

jointing to pipe.

P 005 150mm diameter cast iron floor trap with hinged No. 78.10 S P 5

grating, hopper and 100mm diameter outgo and

concrete surround (at ground floor slab) including

hacking to remove existing damaged trap and jointing

to pipe.


SOR Page 36


Waste Trap

P 006 100mm UPVC adjustable 'S' trap complete with No. 15.10 S P 6

hopper, vent socket and grating including jointing to

waste pipe

P 007 100mm UPVC adjustable 'P' trap complete with No. 12.70 S P 7

hopper, vent socket and grating including jointing to

waste pipe

P 008 32 mm PVC `S' trap No. 4.90 S P 8

P 009 32 mm PVC `P' trap No. 4.90 S P 9





Bottle Trap

P 014 32mm PVC bottle trap No. 4.90 S P 14

P 015 38mm PVC bottle trap No. 4.90 S P 15

P 016 32mm chromium plated bottle trap No. 11.10 S P 16

P 017 38mm chromium plated bottle trap No. 13.10 S P 17

Cast Iron Grating

* Cast iron round gratings including bedding in

cement mortar of the following diameter *(018 021)

P 018 50mm No. 1.60 S P 18

P 019 75mm No. 2.00 S P 19

P 020 100mm No. 2.50 S P 20

P 021 150mm diameter No. 2.50 S P 21

P 022 100mm chromium plated round hinged No. 4.30 S P 22

grating with square frame including bedding

in cement mortar

P 023 6mm thick 150mm square UPVC grating with/without No. 4.60 S P 23

perforation with hinges/frame including

bedding in cement mortar

P 024 2mm thick 150mm galvanised steel square hinged No. 6.80 S P 24

grating with/without perforation for apron gulley

including embedding in cement mortar


SOR Page 37


UPVC Round Grating

* 6mm thick Round UPVC grating (without PVC

square frame) of the following diameter including

bedding in cement mortar *(025 028)

P 025 50mm No. 1.00 S P 25

P 026 75mm No. 1.30 S P 26

P 027 100mm No. 1.80 S P 27

P 028 150mm No. 2.00 S P 28

UPVC Round Hinged Grating

* 6mm thick round UPVC hinged grating with or

without perforation on UPVC square frame of the

following size including bedding in cement

mortar *(029 031)

P 029 75mm No. 3.40 S P 29

P 030 100mm No. 3.80 S P 30

P 031 150mm No. 4.00 S P 31

*8 to 10mm thick round UPVC hinged grating

on UPVC square frame of the following size

including bedding in cement mortar *(032 034)




UPVC Screw-in Grating

*13mm thick flat UPVC screw-in grating with

square UPVC frame of the following size

including bedding in cement mortar *(035 036)

P 035 not exceeding 100mm diameter No. 11.00 S P 35


*13mm thick domical (cambered outlet grilles with

flat top) UPVC screw-in grating with square upvc

frame including bedding in cement mortar *(037 039)

P 037 not exceeding 100mm diameter No. 11.50 S P 37



P 040 UPVC screw-down domical grating to top of No. 54.90 S P 40

200mm diameter pipe complete with 240mm UPVC

sqaure frame


SOR Page 38


Balcony Grating

* UPVC balcony/roof grating (downspout outlet)

for SS213 pipes with UPVC adjustable body and

UPVC screw-down grating of the

following diameter including removal of existing

damage UPVC/cast iron outlet pipe, preparing

entry for new outlet and make good all works

disturbed *(041 043)

P 041 80mm No. 11.75 S P 41

P 042 100mm No. 17.55 S P 42

P 043 150mm No. 20.30 S P 43

P 044 Round UPVC hinged grating on 150mm No. 5.80 S P 44

square frame with 100mm diameter collar

(hopper) including setting in concrete

P 045 UPVC grille strainer for UPVC grating No. 0.80 S P 45

Dome-Shaped Grating

P 046 75mm diameter galvanised steel spherical dome- No. 5.20 S P 46

shaped grating 2.0mm thick to rainwater down pipe

outlet including hacking and setting with cement

mortar

P 047 100mm diameter galvanised steel spherical dome- No. 6.90 S P 47

shaped grating 2.0mm thick to rainwater down pipe

outlet including hacking and setting with cement

mortar

Cast Iron Dome Grating

P 048 75mm diameter cast iron dome grating including No. 14.90 S P 48

embedding in cement mortar





Strainer

P 051 Purpose made perforated 18G aluminium strainer not No. 84.00 S P 51

exceeding 300mm diameter for street gulley trap

excluding cast iron grating

P 052 Purpose made perforated 18G aluminium strainer No. 92.10 S P 52

exceding 300mm but not exceeding 450mm

diameter for street gulley trap excluding cast iron

grating

P 053 Cast iron strainer for interceptor trap, rectangle/ No. 86.70 S P 53

square type not exceeding 0.72m2

P 054 100mm diameter ductile iron `Y' - pattern trap No. 245.30 S P 54

including flanges and cutting, removing existing

pipe etc

P 055 150mm plastic slot grating including embedding in No. 4.95 S P 55

cement mortar


SOR Page 39


UPVC Anti-Mosquito Device

P 056 UPVC anti-mosquito device (98mm) with body, filter, Set 10.80 S P 56

cover and gully trap grating

P 057 UPVC anti-mosquito device (98mm) with body, filter No. 6.40 S P 57

and cover only

P 058 Anti-mosquito device (counter weight type) without No. 6.40 S P 58

grating

P 059 Auto floating ball cover fitting c/w lightweight PVC No. 7.50 S P 59

ball

(Q) MODIFICATION, REPAIRS & SERVICING

WORKS

Repair to Cast Iron Soil/Waste Pipes

* Re-caulk joints of cast iron soil or waste pipes of

the following diameter including raking out and

providing additional molten lead and spun yarn if

required. *(001 003)

Q 001 75mm Joint 5.80 S Q 1

Q 002 100mm Joint 7.20 S Q 2

Q 003 150mm Joint 8.50 S Q 3

Repair to Cast Iron Rising Main Pipes

Q 004 Re-caulk joints of 100mm diameter cast iron rising Joint 7.30 S Q 4

main pipe including raking out and providing

additional spun yarn and molten lead if required

in upright position


main pipe on level ground including raking out and

providing additional spun yarn and molten lead if

required


main pipe including raking out and providing

additional spun yarn and molten lead if required in

upgright position


main pipe on level ground including raking out and

providing additional spun yarn and molten lead if

required

Q 008 Cut 100mm diameter cast iron rising mains and Joint 35.30 S Q 8

jointing with Gilbault coupling

Q 009 Cut 150mm diameter cast iron rising mains Joint 45.70 S Q 9

and jointing with Gilbault coupling.

Repair to Cleaning Eye

Q 010 Repair leaking, cleaning eyes/oval shaped inspection Job 1.90 S Q 10

covers of cast iron soil and waster pipes of 75mm

and above in diameter

Repair to Service Pipes

Q 011 Repair leaking joints of galvanised service pipe not No. 2.00 S Q 11

exceeding 25mm diameter

Q 012 Repair leaking joints of galvanised service pipe No. 2.50 S Q 12

exceeding 25mm and not exceeding 50mm diameter

Q 013 Repair leaking joints of galvanised service pipes No. 4.30 S Q 13

exceeding 50mm and not exceeding 100mm

diameter


SOR Page 40


Q 014 Repair leaking joints of galvanised service pipes No. 6.30 S Q 14


Q 015 Cut off existing galvanised pipes of diameter No. 3.30 S Q 15

exceeding 50mm but not exceeding 150mm, threads

end and prepare for connection to new pipes

Q 016 Take down service pipes not exceeding 25mm m 3.00 S Q 16

diameter for cleaning and rodding and refixing

including making good joints, and all works disturbed

Q 017 Take down service pipes exceeding 25mm diameter m 3.60 S Q 17

but not exceeding 50mm diameter for cleaning and

rodding and refixing including making good joints,

and all works disturbed

Q 018 Take down service pipes exceeding 50mm diameter m 4.10 S Q 18

for cleaning and rodding and refixing including making

good joints, and all works disturbed

Q 019 Bore holes in water service pipes for use as bin Job 4.30 S Q 19

chute sparge pipes at 50mm centre to centre

(per chute)

Repair to Copper Inlet Pipe

Q 020 Take down copper inlet pipe to w.c. cistern for Job 3.90 S Q 20

clearing and rodding including refixing to position and

make good work disturbed

Repair to WC

Q 021 Repair defective w.c. cistern including renewing No 3.30 S Q 21

washer.

Q 022 Hack hole through wall or floor slabs not exceeding Job 13.10 S Q 22

150mm thick to form chase for entry of water service

pipe (pipe measured separately)

Q 023 Reconstruct concrete stooling of squat pan including Job 32.30 S Q 23

necessary reinforcement bars and rendering with

waterproof cement and sand screed (Replacement of

squat pan and foot rest measured separately)

Clearing Obstructions in Gully Traps/

Pipes/Etc

Q 024 Clear obstructions in traps of basins or sink and Job 4.00 S Q 24

water meter pipes including cleaning up areas on

completion

Q 025 Clear obstructions in floor traps, gulley traps and Job 4.60 S Q 25

urinal trap

Q 026 Clear obstructions in w.c. pan Job 7.80 S Q 26

Q 027 Clear obstructions in soil and waste stack Job 11.80 S Q 27

Q 028 Clear obstructions or for flushing the sullage water or Job 6.00 S Q 28

rain water down pipes right through to sumps or

house drains

Q 029 Manual clearing of obstruction by cleaning rods in Job 11.80 S Q 29

sewers lines (Rate involves 2 adjacent manholes and

the connecting line)

Q 030 Clear obstructions in waste water interceptor trap Job 26.80 S Q 30


SOR Page 41


Q 031 Manual cleaning of obstruction by cleaning rods Job 3.90 S Q 31

in street gulleys including removal of debris

from strainer

Repair to Gate Valve

Q 032 Repair 80mm to 100mm ductile/cast iron gate valve No. 10.10 S Q 32

leakage including renewing gaskets/servicing of

pressure reducing valve 32mm to 50mm diameter

Refix Sanitary Accessories

Q 033 Refix loose sink plug No. 0.30 S Q 33

Q 034 Refix loose sanitary accessories such as mirrors, Job 1.10 S Q 34

brackets, etc./repositioning of flushing system

Q 035 Adjust stop cocks to tilt towards any direction Job 2.00 S Q 35

specified including making good any damaged or

affected piping work

Q 036 Clean white glazed w.c. pans or other white glazed Job 1.60 S Q 36

sanitary fittings to a satisfactory finish free from stain

Flushing of Downfeed Pipe

Q 037 Flush water downfeed pipe at common corridor Stack 14.10 S Q 37

including removal of residue and cleaning up areas

on completion

Repair to Stainless Steel Pipe

Q 038 Repair leaking joints of stainless steel pipe not No. 5.00 S Q 38


Q 039 Repair leaking joints of stainless steel pipe above No. 5.10 S Q 39

42mm diameter but exceeding 75mm diameter

Repair to UPVC Pipes

Q 040 Repair leaking joints of upvc pipe from 50mm No. 5.20 S Q 40

diameter to 150mm diameter.

Repair to Dry Riser

Q 041 Repair leaking joint of dry riser pipe to comply with No. 16.90 S Q 41

FSSD regulation including testing

Locking Device

Q 042 180mm x 110mm x 150mm electro galvanised steel No. 24.40 S Q 42

locking device for refuse chute flushing system,

and taps in common area complete with accessories

Q 043 200mm x 170mm x 195mm electro galvanised steel No. 27.20 S Q 43

locking device for Civil Defence tap at void decks

complete with accessories

Q 044 2mm thick galvanised steel locking device of approved No. 15.50 S Q 44

box or cylindrical pattern for staircase taps, bin

chute stopcock etc complete with chain including all

necessary welding


SOR Page 42


Q 045 Electro galvanised steel locking device 150mm x No. 24.00 S Q 45

150mm x 150mm for taps at void decks and

staircases with and including 100mm heavy duty

internal butt hinges, 25mm groove for insertion of

pipe and two coats of oven baked spray paint and

approved cam lock with a key-alike system

Q 046 Modification of existing locking device for water taps No. 56.70 S Q 46

to incorporate self locking mechanism /

"push-on" type complete with 2 keys (key-alike)

Q 047 200mm x 200mm x 150mm x 1.6mm thick mild steel No. 40.90 S Q 47

box with electro-galvanised coated with 1 coat

of epoxy baked powder coated paint c/w locking

mechanism

Q 048 200mm x 200mm x 200mm self-closing and locking No. 70.00 S Q 48

metal box in powdercoat finish with hidden hinges,

"push-on" lockset and 2 keys (key-alike)

Q 049 Replacement of existing "push-on" type locking No. 34.00 S Q 49

mechanism

Repair to Sensor Flushing System

Repair to Coin Operated Water Dispenser

Q 050 Repair defective coin operated water dispenser Job 16.60 S Q 50

Q 051 Re-install water dispenser (water dispenser provided No. 300.00 S Q 51

by Employer) including all wirings, connections and

making good all works disturbed

Miscellaneous Repairs

Q 052 Break through roof slab to form operning for entry of Opening 13.10 S Q 52

water service pipes and make good all work

disturbed including waterproofing work on completion

of pipe installation to the entire satisfaction of the

roofing specialist. (waterproofing work carried out

by Specialist to be measured separately)

Q 053 Seal up sand holes in cast iron pipes with metalic No. 5.10 S Q 53

epoxy resin as per manufacturer's instruction

including touching up paint to match existing

Q 054 Plug off existing unused tap No. 4.60 S Q 54

Q 055 Clean urinal slab/channel, remove existing cement Job 21.10 S Q 55

pointing between slab/channels etc and repoint with

white cement

Q 056 Supply labour and equipment for locating leaks in Test 161.00 S Q 56

underground pipe

Q 057 Repair leaking tap No. 4.10 S Q 57

Q 058 Repair leaking cast iron pipe at joint of UPVC pipe Joint 6.40 S Q 58

exceeding 75mm but not exceeding 150mm

diameter


SOR Page 43


Q 059 Replace lock only to tap box of refuse chute flushing No. 13.80 S Q 59

system & civil defence tap to match existing

Q 060 Break up existing long bath wall to form opening not Job 36.90 S Q 60

exceeding 0.05m2, complete with new precast

concrete maintenance access door, finish with wall

tiles to match existing including carting away of

debris

Q 061 Break up displaced stool support of water mains and No. 13.40 S Q 61

provide new 305mm x 305mm brick stool support not

exceeding 380mm high including rendering sides and

haunching top in cement mortar (1:3)

Q 062 Repair leak in concrete surround of gulley trap, cast Job 3.60 S Q 62

iron soil pipes, etc. with waterproofed cement mortar

Q 063 Repair concrete surround of squat pan with Job 4.90 S Q 63

waterproofed cement mortar

Q 064 Repair leak in concrete surround of squat pan Job 9.80 S Q 64

including making good finish to match existing

Q 065 Rake out existing pointing at joint between sink and Job 3.60 S Q 65

wall and repoint in white cement

Q 066 Rake out existing pointing at joint between long bath Job 11.50 S Q 66

and wall and repoint in white cement

Q 067 Form 75mm high cement surround at base of w.c. Job 3.90 S Q 67

cistern flush-pipe and squat pan joint to cure leak

(R) CLEANING AND DESILTING WITH

ELECTRO-MECHANICAL EQUIPMENT

R 001 Clear, flush with water, clean, including scrape m 0.70 S R 1

hardened oil sludge, debris etc, off main sewer lines,

branch drain lines using high pressure water jetting

and electro-mechanical equipment with minimum

discharge pressure of 4000 PSI

R 002 Clear, flush with water, clean, including scrape Job 3.30 S R 2

hardened oil sludge, debris etc, off inspection

chamber using high pressure water jetting, electro-

mechanical equipment with minimum discharge

pressure of 4000 PSI and vacuum cleaning

equipment (Including main and branch half round

channels within inspection chambers)


SOR Page 44



hardened oil sludge, debris, etc off street gulleys and

strainers using high pressure water jetting and

electro-mechanical equipment with minimum

discharge pressure of 4000 psi


hardened oil sludge, debris etc, off grease trap/

interceptor using high pressure water jetting and

electro-mechanical equipment with minimum

discharge pressure of 4000 PSI including vacuum

cleaning of solids and semi solids

R 005 Mechanised clearing of obstructions in sewer lines/ Job 18.60 S R 5

manholes by high pressure water pressure water

jetting equipment and/or other electro-mechanical

sewer cleaning equipment with minimum discharge

pressure of 4000 PSI (Rate involves 2 adjacent

manholes and the connection line)

R 006 Clear sediment, sludge and debris in conduit m 0.85 S R 6

(concealed) and box drains using a minimum of

4000 PSI high pressure water jetting machine

including disposal of collected sediment off site

R 007 Flush and remove oil wastes in grease lines in m 2.60 S R 7

industrial workshop

R 008 Pump up and remove oil waste from oil interceptors No. 19.20 S R 8

in industrial workshops

R 009 Flush the 100mm diameter ductile iron `Y' pattern No. 3.30 S R 9

trap

R 010 Clear waste and sludge from oil interceptors in Drum 39.90 S R 10

industrial estates collected in metal drum (209 litres/

46 gallons) and cart away to NEA's dumping ground

in accordance with NEA's requirement and including

dumping fee

(S) WATER TANK REPAIRS, CLEANING &

PAINTING WORK

Supply and Installation/Repairs and

Reinstatement Works for Water Tank

S 001 Patch up holes in m.s. tank walls/bottoms/ covers No. 40.00 S S 1

by welding new piece of m.s. plates not exceeding

0.1m2 (including the cost of use, transportation and

removal of welding equipment)

S 002 Repair leaking joints of water storage tank with m 1.80 S S 2

approved non-toxic sealing compound including

tightening of all bolts and nuts

S 003 50mm diameter galvanised steel spring clip with No. 2.90 S S 3

nylon nettings cover at outlet of overflow pipe

S 004 100mm diameter galvanised steel spring clip with No. 3.10 S S 4

nylon mosquito mesh cover at outlet of overflow pipe

S 005 New nylon mosquito mesh of approved quality to m2 1.60 S S 5

open tanks with approved non-toxic sealing

compound


SOR Page 45


S 006 New nylon mosquito mesh of approved quality to No. 1.00 S S 6

150mm square or round grating with approved non-

toxic sealing compound

S 007 0.6mm thick corrugated colour bond galvanised steel m2 36.60 S S 7

cover

S 008 Seal up gaps along edges between covers and tanks m2 1.10 S S 8

with new nylon mosquito mesh of approved quality

with approved non-toxic sealing compound

S 009 75 x 75 x 6mm thick angle iron bracing/stay to water m 5.70 S S 9

tank (including bolts and nuts etc)

S 010 Dismantle and remove of existing bracing/stay off m 1.20 S S 10

site

S 011 Galvanised bolts and nuts to water tanks No. 0.60 S S 11

S 012 Repair of leaky joints of link pipe jointing to water Joint 8.40 S S 12

storage tanks including necessary gaskets, sealing

compound etc

S 013 Repair leaking joint of FRP tank including Panel 5.80 S S 13

dismantling panels, replacement of gaskets, bolts,

nuts and refixing

S 014 Rolled steel joists for support of tanks including bolts, Kg 1.30 S S 14

fixing and painting

S 015 Approved inspection cover to mild steel water tank to No. 29.70 S S 15

match existing

S 016 Approved heavy duty glazed wall/floor tiles including m2 28.70 S S 16

rounded edge tiles etc and cement screed to internal

surface of concrete water tank

S 017 Form an opening through top/side/bottom of concrete No. 19.20 S S 17

water tank for the entry of pipe not exceeding 150mm

diameter including connection of pipe and drilling

holes for bolts.

S 018 Dismantle bulging water tank panel and refix to Panel 6.10 S S 18

proper shape (provision of additional angle steel

bracings/stays, flush and refilling water, sterilize and

test water sample measured separately)

S 019 100mm galvanised iron jam nut complete with No. 5.90 S S 19

washer, etc. to water tank

S 020 Refix fallen off water tank cover. (Provision of m2 1.10 S S 20

additional angle supports, bolts and nuts measured

separately)

S 021 Repair leakage at jamb nut (flushing and refilling No. 6.80 S S 21

water, sterilize and test water sample measured

separately)

S 022 Dismantle and remove from site existing damaged Cover 32.30 S S 22

inspection cover including the 150mm high four-sided

galvanised steel boxing to the access hole and

replace with 0.559mm thick galvanised steel cover

overall size 490 x 490mm including boxing up the

access hole with 150mm high x 0.559mm thick

galvanised steel including pop-riveting


SOR Page 46


S 023 Electrode-holder clamp for water tanks No. 23.50 S S 23

S 024 100mm diameter PVC cap with 100mm diameter Job 27.00 S S 24

UPVC bend (any angles) (SS 213) plain and 100mm

diameter testing openings (F & F) including removal

of existing nylon netting and drill holes of different

sizes to PVC cap and providing of allen type screw

Flushing, Cleaning and Sterilization of Water Tank

S 25 Prepare, sand and remove rust, stains and other m2 0.40 S S 25

sediments from internal surfaces and cover of

stainless steel water tanks including bracing and

flush and clean surfaces

S 26 Prepare, remove all rust, stains and sediments from m2 0.30 S S 26

internal surfaces and cover of FRP/GRP or

reinforced concrete storage or suction tanks, flush

clean surfaces including flushing and refilling tanks

upon completion

S 027 Flush suction/storage tanks and refilling with clean No. 3.30 S S 27

water upon completion (Applicable for repainting of of Tank

mild steel tank or where washing of tank is not

required)

S 028 Sterilise mild steel/FRP/polyethylene lined/stainless m3 0.30 S S 28

steel/concrete water storage tanks to overflow level

S 029 Testing of water samples (any source) including No. 48.70 S S 29

transportation from site to accredited laboratory

and submission of test reports

S 30 Prepare, remove all stains and sediments from m2 0.70 S S 30

internal surfaces and cover of mild steel tank

including bracing, flush and clean surfaces

(Note : only when painting is not required)

S 031 Clean and remove rust stains from external surface m2 0.35 S S 31

of stainless steel water tanks

S 032 Flush steel strainer located after PUB Bulk Meter No. 3.90 S S 32

including dismantling and refixing

Painting Works for mild steel Water Tank

S 033 Prepare, scrap, remove rust and incrustations and m2 0.30 S S 33

other sediments from internal surface and cover of

mild steel tanks, including removal of existing

mosquito netting (if any), flush and clean surfaces,

bracings, and mop up with cloth to dry to receive

new painting (painting measured separately)

S 034 Paint internal surfaces and cover of mild steel water m2 2.50 S S 34

tanks including bracing with one coat of water based

converter. (Surface preparation measured separately)

S 035 Paint internal surfaces and cover of mild steel water m2 4.70 S S 35

tanks including bracing with two finishing coats of

water based paint. (Surface preparation measured

separately)

S 036 Paint internal surfaces of mild steel water tanks m2 5.80 S S 36

including bracing with two finishing coats of epoxy

based paint. (Surface preparation measured

separately)


SOR Page 47


S 037 Paint external surfaces of mild steel water tanks with m2 2.40 S S 37

one coat of rust convertor of water based.

(Surface preparation measured separately)

S 038 Paint external surfaces of mild steel water tanks m2 3.20 S S 38

with one coat of epoxy based primer. (Surface

preparation measured separately)


one finishing coat water based paint.



one finishing coat of epoxy based paint.


S 041 Engage Professional Engineer to inspect and certify Blk 500.00 S S 41

the water installation were fit and safe to use,

properly maintained and free from leakage. (This rate

shall not be subject to percentage adjustment

stated in the Form of Tender)

S 042 Replace FRP/GRP panel for water tank (flush and panel 406.90 S S 42

refilling water, sterilize and test water sample shall

be measured separately)

(T) MATERIALS SUPPLY

* The following items are for supply of materials only.

(Works performed by the standby plumber as

specified) *(001 018)

T 001 13mm diameter light guage metal flexible inlet tube No. 1.80 S T 1

to cistern/basins and taps complete with connectors

T 002 13mm rubber washer to tap and stop cock No. 0.40 S T 2

T 003 Coupling washer to meter pipe connector No. 0.30 S T 3

T 004 Ball valve washer to w.c. cistern No. 0.30 S T 4

T 005 Rubber washer to w.c. cistern syphon No. 0.50 S T 5

plunger

T 006 13mm diameter copper ring to service pipe No. 0.50 S T 6






T 012 13mm diameter DZR type brass stop cock No. 8.40 S T 12

T 013 13mm diameter DZR type high pressure No. 8.40 S T 13

brass screw down bib tap

T 014 13mm diameter copper piping 300mm long with No. 3.30 S T 14

connectors at both ends for fittings

T 015 2mm thick 75mm diameter galvanised steel No. 1.75 S T 15

spherical dome-shaped grating


SOR Page 48


T 016 2mm thick 150mm diameter galvanised steel No. 3.45 S T 16

square hinged with/without perforated grating for

apron gully

T 017 150mm UPVC screw floor trap grating No. 7.50 S T 17

T 018 13mm brass bib key tap including detachable spindle No. 7.50 S T 18

head

(U) DAYWORKS

Labour

U 001 Supply of labourer for miscellaneous work Hour 6.00 S U 1

U 002 Supply of skilled plumber Hour 12.50 S U 2

U 003 Supply of skilled electrician Hour 12.50 S U 3

U 004 Wireman Hour 10.00 S U 4

U 005 Attendance fee in response to EMSU instruction after Call 30.00 S U 5

office hours (For those cases where no repair work

is required after reaching the site)

Plant

U 006 Motor Lorry (Pick-up) not more than 2.50 tonne Hr 18.30 S U 6

including fuel and driver

U 007 Motor Lorry 3 tonne size including fuel and driver Hr 25.60 S U 7

U 008 Motor Lorry mounted with crane including Hr 29.40 S U 8

fuel and operator (6 1/2 tonne lifting capacity)

U 009 Motor Lorry mounted with crane including Hr 38.00 S U 9

fuel and operator (10 tonne lifting capacity)

U 010 Air compressor with air delivery capacity Hr 21.10 S U 10

not less than 4 cu m per minute including

pneumatic tools, fuel and tool sharpening

(no labour)

U 011 Wheel or crawler shovel or excavator loader Hr 59.20 S U 11

with back hoe bucket not exceeding 0.4 cu m

or 1.30 cu m loader bucket capacity including

fuel and driver e.g. Kobe 904, JCB


Sanitary SORs

Documents

Transcript of Sanitary SORs