SANDRO - Ares IllSandro 65 SANDRO.1 hite .6 rey .3 Anthracite . ack .18 Dee ron Reguation 872012 -...
Transcript of SANDRO - Ares IllSandro 65 SANDRO.1 hite .6 rey .3 Anthracite . ack .18 Dee ron Reguation 872012 -...
211
LED VERSION: Class A/A+/A++Luminaire supplied with integrated LED modules that cannot be replaced
A++
A+
A
Sandro
SANDRO65
.1 White .6 Grey .3 Anthracite .18 Deep Brown.4 Black
EU Regulation 874/2012 - Illumination equipment energy classes
LED VERSION:Class A/A+/A++Luminaire supplied with integrated LED modules that cannot be replaced
• Bollard light• Configuration: extruded aluminium structure.
Polycarbonate diffuser: satin UV-stabilised.• Double layer coating for high resistance to corrosion:
the aluminium components are painted with a double coat using powders which are compliant with QUALICOAT standards: a first layer of epoxy powder (with excellent chemical and mechanical resistance) and a second finishing layer of polyester powder (resistant to UV rays and atmospheric agents). The entire painting process of the aluminium fitting starts from components which have been sandblasted in advance to make the surface more porous and increase the adherence of the paint. Ares effects alkaline and acid washing to clean the surfaces completely, then rinses with demineralised water to remove any residue particles, subsequently a chemical conversion treatment is done to protect against rusting.
• Protection rating: IP65• In compliance with EN 60598-1 standards• Class of insulation: II• Installation: the luminaire is equipped with a piece of cable
and a wiring kit with crimp connectors and an adhesive heat-shrink tubing for a watertight electrical connection. The use of a corrugated tube (Ø 30-50mm) allows an easier connection to the line. We recommend installation on a concrete basement or surface, directly with bolts or through the dedicated fixing plate (to be ordered separately). Outdoor use requires suitable flexible cables.
• We recommend the use of a connection system with a protection degree greater than or equal to the protection degree of the luminaire.
• During the installation and the maintenance of the fixtures it is important to be careful and avoid damages on the paint coating. Damages on the coating exposed to outdoor conditions or water, could cause corrosion.Chemical substances affect the anticorrosion covering protection.
Protection againstimpact.IK 10 - 20,00 joule
Pre-wired with approx 200mm of cable
Bollard light
212
C0 / C180 C90 / C270
cd / 1000 lm
60˚
120˚
90˚
450
-2-4 20m
1
0
Lux
121
41
101181
4-2
C0 / C180 C90 / C270
cd / 1000 lm
60˚
120˚
90˚
450
-2-4 20m
2
0
Lux
4-2
1
1
1
1
1
1
21
21
21101
101
161 161381
1
21161
381
500
245 60
160 100
90
0
245 60
160 100
Sandro
65
65
502009White 2700K Lm LED 558 ≠ Lm OUTPUT 299
502007 White 2700K Lm LED 558 ≠ Lm OUTPUT 299
502006White 3000K Lm LED 600 ≠ lm OUTPUT 321
502003White 3000K Lm LED 600 ≠ lm OUTPUT 321
502005White 4000K Lm LED 650 ≠ lm OUTPUT 347
502002 White 4000K Lm LED 650 ≠ lm OUTPUT 347
@4000K
@4000K
Light Source: Power LED / 5,5W / Total power 8W / CRI>80 / 100÷240V / Integral electronic power supply
Light Source: Power LED / 5,5W / Total power 8W / CRI 80 / 100÷240V / Integral electronic power supply
Sandro - H.500mm
Sandro - H.900mm
213Sandro
170
100
160
65
5030
Incorrect Fixing MethodCorrect Fixing Method Correct Fixing MethodBollard �xed on plinth + plug Bollard �xed on plinth + �xing bolts Do not �x the bollard directly on the ground
acc. code
prod. code 138 237
502002 • •502003 • •502004 • •502005 • •502007 • •502009 • •
Accessories: Sandro
138BASE PLATE AND FIXING BOLTS160 x 100 x H 170mm
237SPD: (SURGE PROTECTION DEVICE) 275Vac MAXIMUM DISCHARGE CURRENT 10KA (8/20μs) MAXIMUM OPERATING CURRENT 5ASUITABLE FOR SERIES CONNECTION - IP66
Incorrect Fixing MethodDo not fix the bollard directly on the ground
Correct Fixing MethodBollard fixed on plint + suitable installation screws
Correct Fixing MethodBollard fixed on plinth + fixing bolts