Customer ServiceAmericas: 800-359-5520 • 651-484-7988 • info@sanus.comEurope, Middle East, and Africa: + 31 40 2324700 • europe.sanus@milestone.com Asia Pacifi c: 86 755 8996 9226 • sanus.ap@milestone.com

SANUS · 2221 Hwy 36 West · Saint Paul, MN 55113 USA

©2011 Milestone AV Technologies, a Duchossois Group Company. All rights reserved. Sanus is a division of Milestone. All other brand names or marks are used for identifi cation purposes and are trademarks of their respective owners.

We are here to help!Please contact Customer Service with any questions.

accents.sanus.com(6904-002015 <01>)

SAN55BA Instruction Manual

6904-002015 <01>2

Specifi cations

Weight capacity--DO NOT EXCEED: 58.9 kg (130 lbs) includes TV, mount, and any accessories

CAUTION: Avoid potential personal injuries and property damage!

Do not use this product for any purpose not explicitly specifi ed by Sanus Systems. The wall must be capable of supporting fi ve times the weight of the monitor and mount combined. This product is not designed for use in metal stud walls! If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this

product, contact manufacturer Customer Service or call a qualifi ed contractor. Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.

IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE

484.1 mm19.06 in.

177.8 mm7.0 in.

736.6 mm29 in.

50 mm to 758 mm

450 mm17.72 in.

26.5 mm1.05 in.

6904-002015 <01> 3

Required Tools

Supplied Parts and Hardware

WARNING: This product contains small items that could be a choking hazard if swallowed.

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!

NOTE: M4, M6, or M8 describes the diameter, mm describes the length of screws that are labeled M# x ##mm. Not all hardware included will be used.

5.5mm

(7/32 in.)

13mm

(1/2 in.)

13mm

(1/2 in.)

M4 x 12mm[04] x 4

[01] x 1

[02] x 1 [03] x 1

M4 x 30mm[05] x 4

M6 x 12mm[06] x 4

M8 x 16mm[09] x 4

[15] x 6 [16] x 65⁄16 in. x 2 ½ in.

[17] x 6

M6 x 20mm[07] x 4

M6 x 35mm[08] x 4

M8 x 40mm[10] x 4

M4[11] x 8

M4[13] x 4

M6/M8[12] x 4 M6/M8

[14] x 4

3⁄16 in. Hex Key[18] x 1

6904-002015 <01>4

1 Select TV Hardware and Mount TV Brackets

1-1 Choose screw length and diameter

1-2 Select the hardware confi guration

Hand thread screws into the threaded inserts on the back of your TV to determine the correct screw diameter (M4, M6, or M8).

Verify that there are adequate threads to secure the brackets to the monitor. If you encounter resistance, stop immediately and contact customer service.

CAUTION: Avoid potential personal injuries and property damage! Use the shortest screw and spacer combination to accomodate your needs. Using hardware that is too long may damage your monitor’s internal components.

Your TV type will help you determine which hardware confi guration to use. Match your type of TV to the suggested hardware confi guration on the next page.

A. Installation option without spacers (TVs with fl at backs).

B. Installation option using spacers (TVs with obstructed backs or inset mounting holes).

A B

6904-002015 <01> 5

1-3 Attach selected hardware

M4/M6/M8

M6/M8

M4

[04], [06],

[07], [09]

[11], [12]

[03]

[03]

[02]

[02]

[08], [10]

[13]

[14]

[11]

[11]

[12]

[05]

For TVs with an irregular back

Ensure the brackets is level on the back of the TV.

Standard confi gurations are shown. For special applications, or if you are uncertain about your hardware selection, contact Customer Service.

For TVs with a fl at back

Ensure the bracket is level on the back of the TV.

If you require additional space for cables, recesses, or protrusions, see the confi guration below.

[02], [03]

[02], [03]

[02], [03]

6904-002015 <01>6

For ease of access, straps should be level with the bottom of the TV.

2 Adjust Strap

40.6 - 61 cm

(16 - 24 in.)

< 16 mm

(5/8 in.)

3 Wall Mounting - Wood Stud

3-1 Locate stud

3-2 Level wall plate [01] and mark hole locations

Verify the center of the stud using an awl, a thin nail, or an edge to edge stud fi nder.

CAUTION: Avoid potential personal injuries and property damage!

Any material covering the wall must not exceed 16 mm (5/8 in.). Minimum wood stud size: common 2 x 4 in (nominal 1.5 x 3.5 in).

[01]

5.5mm

(7/32 in.)

13mm

(1/2 in.)

6904-002015 <01> 7

3 Wall Mounting - Solid Concrete

and Concrete Block

3-1 Level wall plate [01] and mark hole locations

[16]

[17]

[01]

[01]

3-3 Drill pilot holes as illustrated

3-4 Tighten lag bolts [17] only until the washers [16] are pulled fi rmly against the wall plate [01]

3 Wall Mounting - Wood Stud - continued

CAUTION: Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage: pilot holes MUST be drilled to a depth of 75 mm (3 in.), using a 5.5 mm (7/32 in.) diameter drill bit.

CAUTION: Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage DO NOT over-tighten the lag bolts [17].

75 mm3 in.

CAUTION: Avoid potential personal injuries and property damage! Mount the wall plate [01] directly onto the concrete surface. Minimum solid concrete thickness: 8 in. Minimum concrete block size: 8 x 8 x 16 in.

13 mm

(1/2 in.)

13 mm

(1/2 in.)

6904-002015 <01>8

3-2 Drill pilot holes as illustrated

3-3 Insert anchors [15]

3-4 Tighten lag bolts [17] only until the washers [16] are pulled fi rmly against the wall plate [01]

75 mm

(3 in.)

[15]

3 Wall Mounting - Solid Concrete and Concrete

Block - continued

CAUTION: To avoid potential injuries or property damage:

Pilot holes MUST be drilled to a depth of 75 mm (3 in.) using a 13 mm

(1/2 in.) diameter drill bit. Never drill into the mortar between blocks.

CAUTION: To avoid potential injuries or property damage be sure the anchors [15] seat fl ush with the concrete surface.

CAUTION: Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage DO NOT over-tighten the lag bolts [17].

[01]

[16]

[17]

6904-002015 <01> 9

4 Hang the TV with Mounting Brackets onto the Wall Plate

To remove the TV

HEAVY! You will need assistance with this step.

Pull down the straps (S) to disengage the locking tabs, then lift the TV off the wall plate. Swing TV / bracket assembly forward from the bottom and lift the TV from the wall mount.

HEAVY! You will need assistance with this step.

Install the TV / Bracket assembly by fi tting the top hook of the mounting bracket over the top edge of the wall mount. Swing the mounting bracket down until the spring loaded locking tabs (L) slip over and fully engages the bottom edge of the wall mount.

CAUTION: Be sure the locking tabs (L) engage into the locked position. There is an audible click when the parts are correctly assembled.

(L)

(S)

6904-002015 <01>10

Milestone AV Technologies and its affi liated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or suffi ciency of the information contained in this document.