SAIB Rifles & Carbines with ARS
-
Upload
caleb-de-armas -
Category
Documents
-
view
225 -
download
0
Transcript of SAIB Rifles & Carbines with ARS
-
8/7/2019 SAIB Rifles & Carbines with ARS
1/104
The Soldier: Americas Most Deployed Combat System
1. Upon entering the site you will be asked to select your weapon. Click on thepicture of your weapon
2. You will then be taken to a page with pictures of your selected weapon, with avariety of devices, and/or multiple device configurations. Click on the picture of theweapon and devices for which you wish to obtain information.
3. You will be taken to pages that contain mounting instructions, with supportingdiagrams, and a Bore Sight Offset target.
a. You may review the data, printing those items of information that you desire.
NOTE
When printing the Bore Sight Offset Targets insure that the printer margins are set to.25 inches, Top, Bottom, Left and Right. These targets are properly proportioned to
be used directly in the bore sighting of your weapons and devices.b. Once you have finished reviewing the information you may select the
Return to Weapon Selection button to make additional choices.
NOTE: All references contained in the following pages pertain to the Small ArmsIntegration Book, dated January, 2006
Project Manager Soldier WeaponsSmall Arms Integration Book
Rifles & Carbines Equipped with Adapter Rail System
ENTER
-
8/7/2019 SAIB Rifles & Carbines with ARS
2/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 2
Click On Your Weapon
M203A2(On M4/M4A1
Carbine w/M4 ARS)
M4/M4A1 Carbinewith M4 Adapter Rail
System
M16A4 Rifle withM5 Adapter Rail
System
M203A2(On M16A4 w/M5 ARS)
-
8/7/2019 SAIB Rifles & Carbines with ARS
3/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 3
Select Your M16A4 Rifle w/M5 Adapter Rail System & Device Combination(Page 1 of 5)
Click for AdditionalConfigurations
(Pictures Not to Scale)
-
8/7/2019 SAIB Rifles & Carbines with ARS
4/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 4
Select Your M16A4 Rifle w/M5 Adapter Rail System & Device Combination(Page 2 of 5)
(Pictures Not to Scale)
Click for AdditionalConfigurations
AN/PAQ-4C Using
Mounting Bracket/Picatinny RailGrabber
-
8/7/2019 SAIB Rifles & Carbines with ARS
5/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 5
Select Your M16A4 Rifle w/M5 Adapter Rail System & Device Combination(Page 3 of 5)
(Pictures Not to Scale)
Click for AdditionalConfigurations
AN/PAQ-4C UsingInsight Low
Profile RailGrabber
-
8/7/2019 SAIB Rifles & Carbines with ARS
6/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 6
Select Your M16A4 Rifle w/M5 Adapter Rail System & Device Combination(Page 4 of 5)
(Pictures Not to Scale)
Click for AdditionalConfigurations
-
8/7/2019 SAIB Rifles & Carbines with ARS
7/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 7
Select Your M16A4 Rifle w/M5 Adapter Rail System & Device Combination(Page 5 of 5)
Click to Return toWeapon Selection
-
8/7/2019 SAIB Rifles & Carbines with ARS
8/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 8
Select Your M203A2 Grenade LauncherMounted on M16A4 w/M5 ARS & Device Combination
Click to Return toWeapon Selection
-
8/7/2019 SAIB Rifles & Carbines with ARS
9/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 9
Select Your M4 Carbine w/M4 Adapter Rail System & Device Combination(Page 1 of 5)
Click for AdditionalConfigurations
(Pictures Not to Scale)
-
8/7/2019 SAIB Rifles & Carbines with ARS
10/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 10
Select Your M4 Carbine w/M4 Adapter Rail System & Device Combination(Page 2 of 5)
(Pictures Not to Scale)
Click for AdditionalConfigurations
M4/M4A1 & M4 ARS withAN/PAQ-4C & AN/PAS-13A/B(V)1/3
MTD
AN/PAQ-4C UsingMounting Bracket/
Picatinny Rail Grabber
-
8/7/2019 SAIB Rifles & Carbines with ARS
11/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 11
Select Your M4 Carbine w/M4 Adapter Rail System & Device Combination(Page 3 of 5)
(Pictures Not to Scale)
Click for AdditionalConfigurations
M4/M4A1 & M4 ARS withAN/PAQ-4C & AN/PAS-13A/B(V)1/3
MTD
AN/PAQ-4C UsingInsight Low Profile Rail
Grabber
-
8/7/2019 SAIB Rifles & Carbines with ARS
12/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 12
Select Your M4 Carbine w/M4 Adapter Rail System & Device Combination(Page 4 of 5)
(Pictures Not to Scale)
Click for AdditionalConfigurations
-
8/7/2019 SAIB Rifles & Carbines with ARS
13/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 13
Select Your M4 Carbine w/M4 Adapter Rail System & Device Combination(Page 5 of 5)
Click to Return toWeapon Selection
-
8/7/2019 SAIB Rifles & Carbines with ARS
14/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 14
Select Your M203A2 Grenade LauncherMounted on M4/M4A1 w/M4 ARS & Device Combination
(Pictures Not to Scale)
Click to Return to
Weapon Selection
-
8/7/2019 SAIB Rifles & Carbines with ARS
15/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 15
M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
the device is removed from the rail the operator must take note of the position at which the device waszeroed, and return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.5 Squares Right, 8.0 Squares Up- Top Rail: 1.7 Squares Right, 0.7 Squares Down- Right Side Rail Mounting: 5.9 Squares Left, 3.5 Squares Up
10m Boresight Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.0 cm Left, 4.3 cm Down- Top: 1.8 cm Left, 3.9 cm Up
- Right Side Rail Mounting: 6.0 cm Right, 0.9 cm DownSee Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
The AN/PAQ-4C may be mounted on the left, top orright side rails using the Mounting Bracket/Picatinny Rail Grabber (NSN 5340-01-458-0473)depicted in the diagram at left.
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Attach the Mounting Bracket/Picatinny RailGrabber(1) to the AN/PAQ-4C (2) using thethumbscrew on the AN/PAQ-4C.
2. Loosen the clamping knob until the railgrabber/mount has sufficient space to fit over the leftside rail (3). Tighten the clamping knob until two clicksare heard.
3. Install the remote switch in a convenient locationusing the provided cable hangers.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
16/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PAQ-4C Using MountingBracket/Picatinny Rail Grabber
AN/PAQ-4B/CLeft Rail
6.0L/4.3D
AN/PAQ-4B/CTop Rail1.8L/3.9U
AN/PAQ-4B/CRight Rail6.0R/0.9D
Laser Bore Light0/0
Click to Return toWeapon Selection
Bore Sighting the AN/PAQ-41. Stabilize Weapon.2. Align Laser Borelight on its dot (See Annex F)3. Adjust Device until aiming laser is centered on the dot-cross hair.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
17/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 17
M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber
The Aiming Light is mounted on the front left-hand railusing the Insight rail grabber bracket (NSN 5340-01-458-0990) when it is desired to keep the Aiming Lightas close as possible to the barrel.
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. For ease of installation install the grabber on therail first, then mount the device on the grabber.
2. Loosen the clamping knob (1) until the rail grabberhas sufficient space to fit over the left side rail (2).Hand Tighten the clamping knob (1).
3. Turn the ON/OFF Switch CCW to the #1OFF/STORAGE position.
4. Position the Aiming Light on the bracket mounting rail. Hand tighten the Thumbscrew (3) to secure the AimingLight.
5. Install the remote switch (not shown) in a convenient location using the provided cable hangers.
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If howeverthe device is removed from the rail the operator must take note of the position at which the device was zeroed,
and return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows
25m Fired Zero Offsets:
- Left Side Rail Mounting: 4.2 Squares Right; 8.6 Squares Up- Top Rail Mounting: 1.7 Squares Right; 1.8 Squares Up- Right Side Rail Mounting: 4.3 Squares Left; 3.4 Squares Up
10m Boresight Offsets:
- Left Side Rail Mounting: 4.3 cm Left; 4.2cm Down- Top Rail Mounting: 1.8 cm Left; 2.2 cm Up- Right Side Rail Mounting: 4.3 cm Right; .7 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.
See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
18/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PAQ-4C UsingInsight Low Profile Rail Grabber
AN/PAQ-4B/CLeft Rail4.3L/4.2D
AN/PAQ-4B/CTop Rail1.8L/2.2U
AN/PAQ-4B/CRight Rail4.3R/0.7D
Laser Bore Light0/0
Click to Return toWeapon Selection
ore Sighting the AN/PAQ-4. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F) Adjust Device until aiming laser is centered on the dot-cross hair.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
19/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 19
M4/M16A4 MWSAN/PAS-13A/B(V)1/3 L/HWTS
(See Annex B for Target Prep Instructions)
Install the AN/PAS-13(V)1 on the Modular WeaponSystem (2) using the sights rail grabber/mount (NSN
1240-01-490-0737, Part No. A3281312-1) (3).
NOTE
Procedures outlined below pertain to either M4 or M4A1variants.
NOTE
Although the AN/PAS-13(v)1, LWTS is depicted both theAN/PAS-A/B(V)2 or (V)3 M/HWTS may also be mountedon the weapon using the same methods described below.In order to mount the AN/PAS-A/B(V)2 or (V)3 M/HWTSthe unit armorer must first install a Spacer Kit, M4 (NSN
5340-01-502-7971) to the TWS.
WARNINGMake sure the weapon is CLEAR and on SAFE before proceeding.
1. Remove carrying handle (not shown) from rail (4) of weapon. Retain carrying handle.
2. Loosen the clamping knob (5) until the jaws move far enough apart to fit over the rail (4).
3. Select a slot on rail. Any slot may be used as long as rail grabber/mount does not hang over edge of rail. If the
TWS is removed from the rail the operator must note the position at which the device was zeroed, and return thedevice to that position in order to retain zero.
4. Place rail grabber/mount on rail and tighten clamping knob (5) until two clicks are heard.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 Squares Left/Right; 4.5 Squares Down- AN/PAS-13A/B(V)3 (HWTS): 0.0 Squares Left/Right; 6.0 Squares Down
10m Boresight Offsets:
- AN/PAS-13B(v)1 (LWTS): 0.0 cm Left/Right; 7.9 cm Up- AN/PAS-13A/B(V)3 (HWTS): 0.0 cm Left/Right; 9.4 cm Up
See Annex BSIGHT/ACCESSORY OPERATING INSTRUCTIONS for instructions on preparation of AN/PAS-13 targets.
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
20/104
-
8/7/2019 SAIB Rifles & Carbines with ARS
21/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 21
M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber
The AN/PEQ-2A (1) is mounted on the front left, top, orright rail (2) using the Insight Rail Grabber Bracket
(NSN 5340-01-458-0990) (3).
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Mount the rail grabber to the AN/PEQ-2A using thethumbscrew (4) as shown.
2. Loosen the clamping knob (5) on the rail grabberuntil the rail grabber has sufficient space to fit over theleft side rail.
3. Position and tighten the Rail Grabber by turning theknob clockwise.
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
he device is removed from the rail the operator must take note of the position at which the device was zeroed, andreturn the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets:
- Left Side Rail Mounting: 5.0 Squared Right; 4.0 Squares Up- Top Rail Mounting: 2.0 Squares Left; 1.2 Squared Up- Right Side Rail Mounting: 0.5 Squares Left; 8.5 Squares Up
10m Boresight Offsets:
- Left Side Rail Mounting:Aiming: 4.5 cm Left; 1.0 cm DownFlood: 4.5 cm Left; 5.0 cm Down
- Top Rail Mounting:
Aiming: 2.0 cm Right; 2.3 cm UpFlood: 2.0 cm Left; 2.3 cm Up- Right Side Rail Mounting:
Aiming: 4.5 cm Right; 4.4 cm DownFlood: 4.5 cm Right; 0.4 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for Bore
Sight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
22/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PEQ-2A Using Insight Low ProfileRail Grabber
Laser Bore Light0/0
AN/PEQ-2A AimLeft Rail4.5L/1.0D
AN/PEQ-2A Flood
Left Rail4.5L/5.0D
AN/PEQ-2A FloodTop Rail2.0L/2.3U
AN/PEQ-2A AimTop Rail
2.0R/2.3U
ore Sighting the AN/PEQ-2. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F). Adjust Device until aiming laser is centered on the dot-cross hair.. Adjust AN/PEQ-2A Flood Light until the laser is centered on the designated dot.
Click to Return toWeapon Selection
AN/PEQ-2A Aim
Right Rail4.5R, 4.4D
AN/PEQ-2A FloodRight Rail4.5R/0.4D
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
23/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 23
M4/M16A4 MWSAN/PVS-4A
To mount the AN/PVS-4A to the MWS the unitArmorer must install a spacer (NSN 5365-01-
447-8991) and a rail grabber/mount (NSN 5340-01-449-8533).
1. Loosen two knobs (1) on carrying handle(2). Remove carrying handle from upperreceiver rail (3). Retain carrying handle.
2. Install spacer (5) on AN/PVS-4A (7) usingthe two screws provided. Attach railgrabber/mount (6) to the spacer (5) using thetwo screws provided. (Pre-assembled by UnitArmorer.)
3. Loosen the clamping knob (8) until sufficientspace exists to place the clamping jaws oneither side of the mounting rail (3). Tightenclamping knob (8) until two clicks are heard.
4. The AN/PVS-4A may be placed on theupper receiver rail in the most convenient slot forthe operator, as long as the rail grabber/mountdoes not extend beyond the rail.
5. If the AN/PVS-4A is removed the operator must take note of the position at which the device was zeroed, andeturn the device to that same position to insure zero is retained.
NOTE
Item (6) is depicted upside down in order to clearly show the bar which must fit into one of the slots on the rail.NOTE
The AN/PVS-4A may also be mounted on the M4 handle in the same manner as is used to mount on the handleof the M16A2. Items 5 & 6 will not be required when using this method. Insure that the mounting knob is insertedinto the hole in the carrying handle at an angle, due to the smaller gap between the top and bottom of the handle
(item 2 above).
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: 0.0 Squares Left/Right; 4.4 Squares Down
10m Boresight Offsets: 0.0 cm Left/Right; .7.6 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for Bore
Sight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
24/104
10m Boresight M4/M16A4 MWSAN/PVS-4A
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
AN/PVS-4Receiver Rail
0.0/7.6U
Laser Bore Light0/0
Click to Return toWeapon Selection
Bore Sighting the AN/PVS-4A1. Stabilize Weapon.2. Aim AN/PVS-4A at Cross Hair and adjust until the bore light strikes the Laser Borelight Dot.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
25/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 25
M4/M16A4 MWSAN/PVS-14
3. Loosen the clamping knob on the weapon mount. Position the weapon mount with the monocular onto theweapons mounting rail. Tighten by turning the clamping knob.
NOTEThere is a ratchet in the weapon mount that prevents over tightening of the clamp. Turn until the knob clicks.
4. Check the position of the monocular by holding the weapon in your normal firing position. Adjust the fore/aftposition of the monocular as necessary by loosening the clamping knob and repositioning the weapon mount onthe weapons mounting rail.
NOTEThe MNVD can be used in conjunction with a collimated dot aiming device mounted on the
forward mounting rail. The brightness control for the aiming device should be set at or near its minimum setting.
Perform the following procedures for weapon mounted operation:
1. Ensure that the batteries are installed per the Tech Manual.
2. Assemble the weapon mount to the monocular as per steps 1 and 2, above.
3. Mount the monocular with adapter onto the M16/M4 receiver rail per steps 3 and 4, above.
4. Rotate the diopter adjustment for the clearest view of the image intensifier screen.
5. Adjust the objective lens focus (Figure 2-1) while observing an object until the sharpest image is obtained.
Target offsets required to properly zero the device to the weapon are as follows: NA. The AN/PVS-14 must beused in conjunction with either a laser aiming device or a collimated dot aiming device to be used as a weaponaiming system.
Click for BoreSight Target
Perform the following procedure to install the weaponmount.
The MNVD is not a weapon sight, however, it can be used
in conjunction with a collimated dot sight or laser aimingdevice.
NOTEIt is recommended that the eyecup be replaced with the
eyeguard during weapon mounted use.
1. Orient the monocular and weapon mount as shown inFigure 2-16, Be sure to align the alignment boss on theweapon mount with the alignment groove in the monocular.
2. Screw in the thumbscrew to secure the monocular tothe weapon mount.
-
8/7/2019 SAIB Rifles & Carbines with ARS
26/104
10m Boresight M4/M4A1/M16A4 with M4/M5 Adapter Rail System withAN/PVS-14 Mounted
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
Laser Bore Light0/0
Click to Return toWeapon Selection
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
27/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 27
M4/M16A4 MWSM68
CAUTIONHand tighten mounting hardware only. Using tools
to tighten mounting hardware could damageequipment.
NOTEThe sight assembly mounts directly to the upper receiverrail on top of the M4/M4A1 and M16A4. The mount is not
required. Make sure the spacer has been installedbefore mounting M68 on M4/M4A1 or M16A4.
1. If the same sight (serial number is on batterycompartment) is installed in the same position on the railon the same weapon, re-zeroing is not required.
2. Install sight assembly (1) on the upper receiver rail(2). Sight may be installed in any position on the upperreceiver rail. Make sure grabber edges area aroundmounting rail and torque bar is in slot. To ensure thatsight assembly is secure, tighten torque knob (3) until itclicks two times. Hand tighten only.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: 0.0 Squares Left/Right; 1.5 Squares Down10m Boresight Offsets: 0.0 cm Left/Right; 5.6 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets. See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
28/104
10m Boresight M4/M4A1/M16A4 with M4/M5 Adapter Rail System withM68 Mounted
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
M68Receiver Rail
0.0/5.6U
Laser Bore Light0/0
Bore Sighting the M681. Stabilize Weapon.2. Aim CCO at the dot cross hair.3. Adjust the CCO until the laser bore light is centered on its dot.
Click to Return toWeapon Selection
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
29/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 29
M4/M16A4 MWSTA-31F (ACOG)
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
CAUTIONHand tighten mounting hardware only. Using
tools to tighten mounting hardware coulddamage equipment.
NOTEThe ACOG sight mounts directly to the upper
receiver rail on top of the M4/M4A1 and M16A4using the integral mount/rail grabber.
1. Install sight assembly (1) on the upper receiver rail (2). Sight may be installed in any position on the upperreceiver rail. Make sure grabber edges area around mounting rail and torque bar is in slot. To ensure that sightassembly is secure, tighten knobs (3). Hand tighten only. Periodically check the knobs to insure that the sight isstill securely attached to the rail.
2. If the same sight (serial number is on battery compartment) is installed in the same position on the rail on thesame weapon, re-zeroing is not required.
Target offsets required to properly zero the device to the weapon are as follows:
10m Boresight Offsets: 0.0 cm Left/Right; 4.8 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets. See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
1
2
3
-
8/7/2019 SAIB Rifles & Carbines with ARS
30/104
-
8/7/2019 SAIB Rifles & Carbines with ARS
31/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 31
M4/M16A4 MWSAN/PEQ-15 Using Integral Low Profile Rail Grabber
The AN/PEQ-15 (1) is mounted on the front left, top, orright rail (2) using its Integral Rail Grabber Bracket not
shown.
WARNING
Make sure the weapon is CLEAR and on SAFEbefore proceeding.
1. The rail grabber is an integral part of the AN/PEQ-15.
2. Loosen the clamping knob (3) on the rail grabberuntil the rail grabber has sufficient space to fit over theleft side rail.
3. Position and tighten the Rail Grabber by turning the
knob clockwise.NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
he device is removed from the rail the operator must take note of the position at which the device was zeroed, andreturn the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets:- Left Side Rail Mounting:
Visible: 2.5 cm Right; 3.5 cm UpIR: 3.5 cm Right; 4.5 cm Up
- Top Rail Mounting:Visible: 2.5 cm Left; 1.5 cm UpIR: 1.5 cm Left; .5 cm Up
- Right Side Rail Mounting:Visible: 3.0 cm Left; 7.0 cm UpIR: 4.0 cm Left; 6.0 cm Up
10m Boresight Offsets:- Left Side Rail Mounting:
Visible: 3.0 cm Left; 0.0 cm Up/DownIR: 4.0 cm Left; 1.0 cm Down
- Top Rail Mounting:Visible: 2.0 cm Right; 1.5 cm UpIR: 1.0 cm Right; 2.5 cm Up
- Right Side Rail Mounting:Visible: 3.0 cm Right; 4.5 cm DownIR: 4.0 cm Right; 3.5 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
1
2
3
-
8/7/2019 SAIB Rifles & Carbines with ARS
32/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PEQ-15 Using Integral Low ProfileRail Grabber
Laser Bore Light0/0
AN/PEQ-15 VisibleTop Rail
2.5R/1.5U
AN/PEQ-15 IRTop Rail
1.0R/2.5U
ore Sighting the AN/PEQ-15. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F). Adjust Device until aiming laser is centered on the dot-cross hair.
Click to Return toWeapon Selection
AN/PEQ-15 IRRight Rail
4.0R/3.5D
AN/PEQ-15 VisibleRight Rail3.0R/4.5D
AN/PEQ-15 IRLeft Rail4.0L/1.0D
AN/PEQ-15Visible
Left Rail3.0L/0.0D
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
33/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 33
M4/M16A4 MWSAN/PAQ-4C Using Bracket/ Picatinny Rail Grabber &AN/PAS-13A/B(V)1/3 (Page 1 of 3 Pages)
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
the device is removed from the rail the operator must take note of the position at which the device waszeroed, and return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.5 Squares Right, 8.0 Squares Up- Top Rail: 1.7 Squares Right, 0.7 Squares Down- Right Side Rail Mounting: 5.9 Squares Left, 3.5 Squares Up
10m Boresight Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.0 cm Left, 4.3 cm Down- Top: 1.8 cm Left, 3.9 cm Up- Right Side Rail Mounting: 6.0 cm Right, 0.9 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
M4 MWS AN/PAQ-4C Mounting Instructions
The AN/PAQ-4C may be mounted on the left, top orright side rails using the Mounting Bracket/Picatinny Rail Grabber (NSN 5340-01-458-0473)depicted in the diagram at left.
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Attach the Mounting Bracket/Picatinny RailGrabber(1) to the AN/PAQ-4C (2) using thethumbscrew on the AN/PAQ-4C.
2. Loosen the clamping knob until the railgrabber/mount has sufficient space to fit over the leftside rail (3). Tighten the clamping knob until two clicksare heard.
3. Install the remote switch in a convenient locationusing the provided cable hangers.
Click forNext Device
-
8/7/2019 SAIB Rifles & Carbines with ARS
34/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 34
M4/M16A4 MWSAN/PAQ-4C Using Bracket/ Picatinny Rail Grabber &AN/PAS-13A/B(V)1/3 (Page 2 of 3 Pages)
(See Annex B for Target Prep Instructions)
Install the AN/PAS-13(V)1 on the Modular WeaponSystem (2) using the sights rail grabber/mount (NSN
1240-01-490-0737, Part No. A3281312-1) (3).
NOTEProcedures outlined below pertain to either M4 or M4A1
variants.
NOTE
Although the AN/PAS-13(v)1, LWTS is depicted both theAN/PAS-A/B(V)2 or (V)3 M/HWTS may also be mountedon the weapon using the same methods described below.In order to mount the AN/PAS-A/B(V)2 or (V)3 M/HWTSthe unit armorer must first install a Spacer Kit, M4 (NSN
5340-01-502-7971) to the TWS.
WARNINGMake sure the weapon is CLEAR and on SAFE before proceeding.
1. Remove carrying handle (not shown) from rail (4) of weapon. Retain carrying handle.
2. Loosen the clamping knob (5) until the jaws move far enough apart to fit over the rail (4).
3. Select a slot on rail. Any slot may be used as long as rail grabber/mount does not hang over edge of rail. If theTWS is removed from the rail the operator must note the position at which the device was zeroed, and return thedevice to that position in order to retain zero.
4. Place rail grabber/mount on rail and tighten clamping knob (5) until two clicks are heard.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 Squares Left/Right; 4.5 Squares Down- AN/PAS-13A/B(V)3 (HWTS): 0.0 Squares Left/Right; 6.0 Squares Down
10m Boresight Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 cm Left/Right; 7.9 cm Up
- AN/PAS-13A/B(V)3 (HWTS): 0.0 cm Left/Right; 9.4 cm Up
See Annex BSIGHT/ACCESSORY OPERATING INSTRUCTIONS for instructions on preparation of AN/PAS-13 targets.
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
35/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Bracket/ PicatinnyRail Grabber & AN/PAS-13A/B(V)1/3 (Page 3 of 3 Pages)
AN/PAQ-4B/C
Left Rail6.0L/4.3D
AN/PAQ-4B/CTop Rail1.8L/3.9U
AN/PAQ-4B/CRight Rail6.0R/0.9D
Laser Bore Light
0/0
Click to Return toWeapon Selection
Bore Sighting the AN/PAQ-41. Stabilize Weapon.2. Align Laser Borelight on its dot (See Annex F)3. Adjust Device until aiming laser is centered on the dot-cross hair.Bore Sighting the AN/PAS-13A/B (V)1/31. Stabilize Weapon.2. Place Thermal signature material or tips of fingers on gray circles.3. Aim between gray circles at cross-hair.
4. Adjust AN/PAS-13A/B(V)1/3 until the bore light laser is centered on its dot.5. You MUST zero reticle in both wide and narrow field of view.
AN/PAS-13A/B (V)3Receiver Rail
0.0/9.4UHeat Source/ Fingers
AN/PAS-13B (V)1Receiver Rail
0.0/7.9U
Heat Source/ Fingers
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
36/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 36
M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber & AN/PVS-4A (Page 1 of 3 Pages)
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
the device is removed from the rail the operator must take note of the position at which the device waszeroed, and return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:25m Fired Zero Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.5 Squares Right, 8.0 Squares Up- Top Rail: 1.7 Squares Right, 0.7 Squares Down- Right Side Rail Mounting: 5.9 Squares Left, 3.5 Squares Up
10m Boresight Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.0 cm Left, 4.3 cm Down- Top: 1.8 cm Left, 3.9 cm Up- Right Side Rail Mounting: 6.0 cm Right, 0.9 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
M4 MWS AN/PAQ-4C Mounting Instructions
The AN/PAQ-4C may be mounted on the left, top orright side rails using the Mounting Bracket/Picatinny Rail Grabber (NSN 5340-01-458-0473)
depicted in the diagram at left.
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Attach the Mounting Bracket/Picatinny RailGrabber(1) to the AN/PAQ-4C (2) using thethumbscrew on the AN/PAQ-4C.
2. Loosen the clamping knob until the railgrabber/mount has sufficient space to fit over the left
side rail (3). Tighten the clamping knob until two clicksare heard.
3. Install the remote switch in a convenient locationusing the provided cable hangers.
Click for
Next Device
-
8/7/2019 SAIB Rifles & Carbines with ARS
37/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 37
M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber & AN/PVS-4A (Page 2 of 3 Pages)
To mount the AN/PVS-4A to the MWS the unitArmorer must install a spacer (NSN 5365-01-
447-8991) and a rail grabber/mount (NSN 5340-01-449-8533).
1. Loosen two knobs (1) on carrying handle(2). Remove carrying handle from upperreceiver rail (3). Retain carrying handle.
2. Install spacer (5) on AN/PVS-4A (7) usingthe two screws provided. Attach railgrabber/mount (6) to the spacer (5) using thetwo screws provided. (Pre-assembled by UnitArmorer.)
3. Loosen the clamping knob (8) until sufficientspace exists to place the clamping jaws oneither side of the mounting rail (3). Tightenclamping knob (8) until two clicks are heard.
4. The AN/PVS-4A may be placed on theupper receiver rail in the most convenient slot forthe operator, as long as the rail grabber/mountdoes not extend beyond the rail.
5. If the AN/PVS-4A is removed the operator must take note of the position at which the device was zeroed, andeturn the device to that same position to insure zero is retained.
NOTEItem (6) is depicted upside down in order to clearly show the bar which must fit into one of the slots on the rail.
NOTEThe AN/PVS-4A may also be mounted on the M4 handle in the same manner as is used to mount on the handle
of the M16A2. Items 5 & 6 will not be required when using this method. Insure that the mounting knob is insertedinto the hole in the carrying handle at an angle, due to the smaller gap between the top and bottom of the handle
(item 2 above).
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: 0.0 Squares Left/Right; 4.4 Squares Down
10m Boresight Offsets: 0.0 cm Left/Right; .7.6 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.
See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
38/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PAQ-4C Using MountingBracket/Picatinny Rail Grabber & AN/PVS-4A (Page 2 of 3 Pages)
AN/PAQ-4B/CLeft Rail
6.0L/4.3D
AN/PAQ-4B/CTop Rail1.8L/3.9U
AN/PAQ-4B/CRight Rail6.0R/0.9D
Laser Bore Light0/0
Click to Return toWeapon Selection
Bore Sighting the AN/PAQ-41. Stabilize Weapon.2. Align Laser Borelight on its dot (See Annex F)3. Adjust Device until aiming laser is centered on the dot-cross hair.
AN/PVS-4Receiver Rail
0.0/7.6U
Bore Sighting the AN/PVS-4A1. Stabilize Weapon.2. Aim AN/PVS-4A at Cross Hair and adjust until the bore light strikes the Laser Borelight Dot.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
39/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 39
M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber w/ AN/PVS-14 & M68 (Page 1 of 4 Pages)
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
the device is removed from the rail the operator must take note of the position at which the device waszeroed, and return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.5 Squares Right, 8.0 Squares Up- Top Rail: 1.7 Squares Right, 0.7 Squares Down- Right Side Rail Mounting: 5.9 Squares Left, 3.5 Squares Up
10m Boresight Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.0 cm Left, 4.3 cm Down- Top: 1.8 cm Left, 3.9 cm Up- Right Side Rail Mounting: 6.0 cm Right, 0.9 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
The AN/PAQ-4C may be mounted on the left or rightside rails using the Mounting Bracket/ PicatinnyRail Grabber (NSN 5340-01-458-0473) depicted inthe diagram at left. Top rail is not available sincethe M68 will be mounted there in a following step.
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Attach the Mounting Bracket/Picatinny RailGrabber(1) to the AN/PAQ-4C (2) using thethumbscrew on the AN/PAQ-4C.
2. Loosen the clamping knob until the railgrabber/mount has sufficient space to fit over the leftside rail (3). Tighten the clamping knob until two clicksare heard.
3. Install the remote switch in a convenient locationusing the provided cable hangers.
Click forNext Device
-
8/7/2019 SAIB Rifles & Carbines with ARS
40/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 40
M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber w/ AN/PVS-14 & M68 (Page 2 of 4 Pages)
Perform the following procedure to install the weaponmount.
The MNVD is not a weapon sight, however, it can beused in conjunction with a collimated dot sight or laser
aiming device.
NOTEIt is recommended that the eyecup be replaced with the
eyeguard during weapon mounted use.
1. Orient the monocular and weapon mount as shownin the figure to the left, Be sure to align the alignmentboss on the weapon mount with the alignment groovein the monocular.
2. Screw in the thumbscrew to secure the monocularto the weapon mount.
3. Loosen the clamping knob on the weapon mount. Position the weapon mount with the monocular onto theweapons mounting rail. Tighten by turning the clamping knob.
NOTEThere is a ratchet in the weapon mount that prevents over tightening of the clamp. Turn until the knob clicks.
4. Check the position of the monocular by holding the weapon in your normal firing position. Adjust the fore/aftposition of the monocular as necessary by loosening the clamping knob and repositioning the weapon mount on
the weapons mounting rail.
NOTEThe MNVD can be used in conjunction with a collimated dot aiming device mounted on the
forward mounting rail. The brightness control for the aiming device should be set at or near its minimum setting.
Perform the following procedures for weapon mounted operation:
1. Ensure that the batteries are installed per the Tech Manual.2. Assemble the weapon mount to the monocular as per steps 1 and 2, above.3. Mount the monocular with adapter onto the M16/M4 receiver rail per steps 3 and 4, above.4. Rotate the diopter adjustment for the clearest view of the image intensifier screen.5. Adjust the objective lens focus while observing an object until the sharpest image is obtained.
Target offsets required to properly zero the device to the weapon are as follows: NA. The AN/PVS-14 must beused in conjunction with either a laser aiming device or a collimated dot aiming device to be used as a weaponaiming system.
Click forNext Device
-
8/7/2019 SAIB Rifles & Carbines with ARS
41/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 41
M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber w/ AN/PVS-14 & M68 (Page 3 of 4 Pages)
CAUTIONHand tighten mounting hardware only. Using tools
to tighten mounting hardware could damageequipment.
NOTEThe AN/PVS-14 was previously mounted to the upper
receiver rail on top of the M4/M4A1 or M16A4.
1. The M68 is mounted on the hand guard top rail,immediately in front of the AN/PVS-14. For older modelM68s make sure the spacer has been installed beforemounting M68 on M4/M4A1 or M16A4.
NOTEIf the same sight (serial number is on battery
compartment) is installed in the same position on the railon the same weapon, re-zeroing is not required.
2. Install sight assembly (1) on the hand guard top rail (2). Sight may be installed in any position on the rail.Make sure grabber edges area around mounting rail and torque bar is in slot. To ensure that sight assembly issecure, tighten torque knob (3) until it clicks two times. Hand tighten only.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: 0.0 Squares Left/Right; 1.5 Squares Down10m Boresight Offsets: 0.0 cm Left/Right; 5.6 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets. See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
1
2
3
M68
-
8/7/2019 SAIB Rifles & Carbines with ARS
42/104
-
8/7/2019 SAIB Rifles & Carbines with ARS
43/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 43
M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber & M68 (Page 1 of 3 Pages)
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
the device is removed from the rail the operator must take note of the position at which the device waszeroed, and return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.5 Squares Right, 8.0 Squares Up- Top Rail: 1.7 Squares Right, 0.7 Squares Down- Right Side Rail Mounting: 5.9 Squares Left, 3.5 Squares Up
10m Boresight Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.0 cm Left, 4.3 cm Down- Top: 1.8 cm Left, 3.9 cm Up- Right Side Rail Mounting: 6.0 cm Right, 0.9 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
M4 MWS AN/PAQ-4C Mounting Instructions
The AN/PAQ-4C may be mounted on the left, top orright side rails using the Mounting Bracket/Picatinny Rail Grabber (NSN 5340-01-458-0473)depicted in the diagram at left.
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Attach the Mounting Bracket/Picatinny RailGrabber(1) to the AN/PAQ-4C (2) using thethumbscrew on the AN/PAQ-4C.
2. Loosen the clamping knob until the railgrabber/mount has sufficient space to fit over the leftside rail (3). Tighten the clamping knob until two clicksare heard.
3. Install the remote switch in a convenient locationusing the provided cable hangers.
Click forNext Device
-
8/7/2019 SAIB Rifles & Carbines with ARS
44/104
-
8/7/2019 SAIB Rifles & Carbines with ARS
45/104
-
8/7/2019 SAIB Rifles & Carbines with ARS
46/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 46
M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber & TA-31F (ACOG) (Page 1 of 3 Pages)
2. Loosen the clamping knob (3) until the rail grabber/mount has sufficient space to fit over the left side rail (4).Tighten the clamping knob until two clicks are heard.
3. Install the remote switch in a convenient location using the provided cable hangers.
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
the device is removed from the rail the operator must take note of the position at which the device waszeroed, and return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.5 Squares Right, 8.0 Squares Up- Top Rail: 1.7 Squares Right, 0.7 Squares Down- Right Side Rail Mounting: 5.9 Squares Left, 3.5 Squares Up
10m Boresight Offsets: (Zeroed to 300m)- Left Side Rail Mounting: 6.0 cm Left, 4.3 cm Down- Top: 1.8 cm Left, 3.9 cm Up- Right Side Rail Mounting: 6.0 cm Right, 0.9 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
M4 MWS AN/PAQ-4C Mounting Instructions
The AN/PAQ-4C may be mounted on the left, top orright side rails using the Mounting Bracket/Picatinny Rail Grabber (NSN 5340-01-458-0473)depicted in the diagram at left.
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Attach the Mounting Bracket/Picatinny RailGrabber(1) to the AN/PAQ-4C (2) using thethumbscrew on the AN/PAQ-4C.
Click forNext Device
1
2
3
4
-
8/7/2019 SAIB Rifles & Carbines with ARS
47/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 47
M4/M16A4 MWSAN/PAQ-4C Using Mounting Bracket/Picatinny RailGrabber & TA-31F (ACOG) (Page 2 of 3 Pages)
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
CAUTIONHand tighten mounting hardware only. Using
tools to tighten mounting hardware coulddamage equipment.
NOTEThe ACOG sight mounts directly to the upper
receiver rail on top of the M4/M4A1 and M16A4using the integral mount/rail grabber.
1. Install sight assembly (1) on the upper receiver rail (2). Sight may be installed in any position on the upperreceiver rail. Make sure grabber edges area around mounting rail and torque bar is in slot. To ensure that sightassembly is secure, tighten knobs (3). Hand tighten only. Periodically check the knobs to insure that the sight isstill securely attached to the rail.
2. If the same sight (serial number is on battery compartment) is installed in the same position on the rail on thesame weapon, re-zeroing is not required.
Target offsets required to properly zero the device to the weapon are as follows:
10m Boresight Offsets: 0.0 cm Left/Right; 4.8 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets. See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
1
2
3
-
8/7/2019 SAIB Rifles & Carbines with ARS
48/104
10m Boresight M4/M16A4 MWSAN/PAQ-4C Using MountingBracket/Picatinny Rail Grabber & TA-31F (ACOG) (Page 3 of 3 Pages)
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
Click to Return toWeapon Selection
Laser Bore Light0/0
ACOGReceiver Rail
0.0/4.8U
Bore Sighting the TA31F (ACOG)1. Stabilize Weapon.2. Align Laser Borelight on its dot3. Adjust ACOG until bottom of the chevron (300M) is centered on the dot-cross hair.
AN/PAQ-4B/CTop Rail1.8L/3.9U
AN/PAQ-4B/CRight Rail6.0R/0.9D
AN/PAQ-4B/CLeft Rail
6.0L/4.3D
Bore Sighting the AN/PAQ-41. Stabilize Weapon.2. Align Laser Borelight on its dot (See Annex F)3. Adjust Device until aiming laser is centered on the dot-cross hair.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
49/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 49
M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &the AN/PAS-13A/B(V)1/3 (Page 1 of 3 Pages)
The Aiming Light is mounted on the front left-hand,top, or right-hand rail using the Insight rail grabberbracket (NSN 5340-01-458-0990) when it is desired tokeep the Aiming Light as close as possible to thebarrel.
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. For ease of installation install the grabber on therail first, then mount the device on the grabber.
2. Loosen the clamping knob (1) until the rail grabberhas sufficient space to fit over the left side rail (2).Hand Tighten the clamping knob (1).
3. Turn the ON/OFF Switch CCW to the #1OFF/STORAGE position.
4. Position the Aiming Light on the bracket mounting rail. Hand tighten the Thumbscrew (3) to secure the AimingLight.
5. Install the remote switch (not shown) in a convenient location using the provided cable hangers.
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If howeverthe device is removed from the rail the operator must take note of the position at which the device was zeroed,
and return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows
25m Fired Zero Offsets:
- Left Side Rail Mounting: 4.2 Squares Right; 8.6 Squares Up- Top Rail Mounting: 1.7 Squares Right; 1.8 Squares Up- Right Side Rail Mounting: 4.3 Squares Left; 3.4 Squares Up
10m Boresight Offsets:
- Left Side Rail Mounting: 4.3 cm Left; 4.2cm Down
- Top Rail Mounting: 1.8 cm Left; 2.2 cm Up- Right Side Rail Mounting: 4.3 cm Right; .7 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.
See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click forNext Device
-
8/7/2019 SAIB Rifles & Carbines with ARS
50/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 50
M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &the AN/PAS-13A/B(V)1/3 (Page 2 of 3)
(See Annex B for Target Prep Instructions)
Install the AN/PAS-13(V)1 on the Modular WeaponSystem (2) using the sights rail grabber/mount (NSN
1240-01-490-0737, Part No. A3281312-1) (3).
NOTEProcedures outlined below pertain to either M4 or M4A1
variants.
NOTE
Although the AN/PAS-13(v)1, LWTS is depicted both theAN/PAS-A/B(V)2 or (V)3 M/HWTS may also be mountedon the weapon using the same methods described below.In order to mount the AN/PAS-A/B(V)2 or (V)3 M/HWTSthe unit armorer must first install a Spacer Kit, M4 (NSN
5340-01-502-7971) to the TWS.
WARNINGMake sure the weapon is CLEAR and on SAFE before proceeding.
1. Remove carrying handle (not shown) from rail (4) of weapon. Retain carrying handle.
2. Loosen the clamping knob (5) until the jaws move far enough apart to fit over the rail (4).
3. Select a slot on rail. Any slot may be used as long as rail grabber/mount does not hang over edge of rail. If theTWS is removed from the rail the operator must note the position at which the device was zeroed, and return thedevice to that position in order to retain zero.
4. Place rail grabber/mount on rail and tighten clamping knob (5) until two clicks are heard.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 Squares Left/Right; 4.5 Squares Down- AN/PAS-13A/B(V)3 (HWTS): 0.0 Squares Left/Right; 6.0 Squares Down
10m Boresight Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 cm Left/Right; 7.9 cm Up- AN/PAS-13A/B(V)3 (HWTS): 0.0 cm Left/Right; 9.4 cm Up
See Annex BSIGHT/ACCESSORY OPERATING INSTRUCTIONS for instructions on preparation of AN/PAS-13 targets.
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
51/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Insight Low ProfileRail Grabber & the AN/PAS-13A/B(V)1/3 (Page 3 of 3 Pages)
AN/PAQ-4B/C
Left Rail4.3L/4.2D
AN/PAQ-4B/CTop Rail1.8L/2.2U
AN/PAQ-4B/CRight Rail4.3R/0.7D
Laser Bore Light
0/0
Click to Return toWeapon Selection
ore Sighting the AN/PAQ-4. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F) Adjust Device until aiming laser is centered on the dot-cross hair.
ore Sighting the AN/PAS-13A/B (V)1/3Stabilize Weapon.Place Thermal signature material or tips of fingers on gray circles.Aim between gray circles at cross-hair.
Adjust AN/PAS-13A/B(V)1/3 until the bore light laser is centered on its dot.You MUST zero reticle in both wide and narrow field of view.
AN/PAS-13A/B (V)3Receiver Rail
0.0/9.4UHeat Source/ Fingers
AN/PAS-13B (V)1Receiver Rail
0.0/7.9U
Heat Source/ Fingers
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
52/104
-
8/7/2019 SAIB Rifles & Carbines with ARS
53/104
-
8/7/2019 SAIB Rifles & Carbines with ARS
54/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Insight Low ProfileRail Grabber & the AN/PVS-4A (Page 3 of 3 Pages)
AN/PAQ-4B/CLeft Rail4.3L/4.2D
AN/PAQ-4B/CTop Rail1.8L/2.2U
AN/PAQ-4B/CRight Rail4.3R/0.7D
Laser Bore Light0/0
Click to Return toWeapon Selection
ore Sighting the AN/PAQ-4. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F) Adjust Device until aiming laser is centered on the dot-cross hair.
AN/PVS-4Receiver Rail
0.0/7.6U
ore Sighting the AN/PVS-4A. Stabilize Weapon. Aim AN/PVS-4A at Cross Hair and adjust until the bore light strikes the Laser Borelight Dot.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
55/104
-
8/7/2019 SAIB Rifles & Carbines with ARS
56/104
-
8/7/2019 SAIB Rifles & Carbines with ARS
57/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 57
M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber,AN/PVS-14, & M68 (Page 3 of 4 Pages)
Click for Bore
Sight Target
CAUTIONHand tighten mounting hardware only. Using tools
to tighten mounting hardware could damageequipment.
NOTEThe AN/PVS-14 was previously mounted to the upper
receiver rail on top of the M4/M4A1 or M16A4.
1. The M68 is mounted on the hand guard top rail,immediately in front of the AN/PVS-14. Make sure thespacer has been installed before mounting M68 onM4/M4A1 or M16A4.
NOTEIf the same sight (serial number is on battery
compartment) is installed in the same position on the railon the same weapon, re-zeroing is not required.
2. Install sight assembly (1) on the hand guard top rail (2). Sight may be installed in any position on the rail.Make sure grabber edges area around mounting rail and torque bar is in slot. To ensure that sight assembly issecure, tighten torque knob (3) until it clicks two times. Hand tighten only.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: 0.0 Squares Left/Right; 1.5 Squares Down10m Boresight Offsets: 0.0 cm Left/Right; 5.6 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.
See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
-
8/7/2019 SAIB Rifles & Carbines with ARS
58/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Insight Low ProfileRail Grabber, AN/PVS-14, & M68 (Page 4 of 4 Pages)
AN/PAQ-4B/CLeft Rail4.3L/4.2D
AN/PAQ-4B/CTop Rail1.8L/2.2U
AN/PAQ-4B/CRight Rail4.3R/0.7D
Laser Bore Light0/0
Click to Return toWeapon Selection
ore Sighting the AN/PAQ-4. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F) Adjust Device until aiming laser is centered on the dot-cross hair.
M68
Receiver Rail0.0/5.6U
ore Sighting the M68. Stabilize Weapon.. Aim CCO at the dot cross hair. Adjust the CCO until the laser bore light is centered on its dot.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
59/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 59
M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &M68 (Page 1 of 3 Pages)
The Aiming Light is mounted on the front left-hand, topor right-hand rail using the Insight rail grabber bracket(NSN 5340-01-458-0990) when it is desired to keepthe Aiming Light as close as possible to the barrel.
WARNINGMake sure the weapon is CLEAR and on SAFEbefore proceeding.
1. For ease of installation install the grabber on therail first, then mount the device on the grabber.
2. Loosen the clamping knob (1) until the rail grabberhas sufficient space to fit over the left side rail (2).Hand Tighten the clamping knob (1).
3. Turn the ON/OFF Switch CCW to the #1
OFF/STORAGE position.
4. Position the Aiming Light on the bracket mounting rail. Hand tighten the Thumbscrew (3) to secure the AimingLight.
5. Install the remote switch (not shown) in a convenient location using the provided cable hangers.
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If howeverthe device is removed from the rail the operator must take note of the position at which the device was zeroed,
and return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows25m Fired Zero Offsets:
- Left Side Rail Mounting: 4.2 Squares Right; 8.6 Squares Up- Top Rail Mounting: 1.7 Squares Right; 1.8 Squares Up- Right Side Rail Mounting: 4.3 Squares Left; 3.4 Squares Up
10m Boresight Offsets:
- Left Side Rail Mounting: 4.3 cm Left; 4.2cm Down- Top Rail Mounting: 1.8 cm Left; 2.2 cm Up
- Right Side Rail Mounting: 4.3 cm Right; .7 cm Down See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.
See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click forNext Device
-
8/7/2019 SAIB Rifles & Carbines with ARS
60/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 60
M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &M68 (Page 2 of 3 Pages)
CAUTIONHand tighten mounting hardware only. Using tools
to tighten mounting hardware could damageequipment.
NOTEThe sight assembly mounts directly to the upper receiverrail on top of the M4/M4A1 and M16A4. The mount is not
required. Make sure the spacer has been installedbefore mounting M68 on M4/M4A1 or M16A4.
1. If the same sight (serial number is on batterycompartment) is installed in the same position on the railon the same weapon, re-zeroing is not required.
2. Install sight assembly (1) on the upper receiver rail(2). Sight may be installed in any position on the upperreceiver rail. Make sure grabber edges area aroundmounting rail and torque bar is in slot. To ensure thatsight assembly is secure, tighten torque knob (3) until itclicks two times. Hand tighten only.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: 0.0 Squares Left/Right; 1.5 Squares Down10m Boresight Offsets: 0.0 cm Left/Right; 5.6 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets. See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
61/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Insight Low ProfileRail Grabber & M68 (Page 1 of 3 Pages)
AN/PAQ-4B/CLeft Rail4.3L/4.2D
AN/PAQ-4B/CTop Rail1.8L/2.2U
AN/PAQ-4B/CRight Rail4.3R/0.7D
Laser Bore Light0/0
Click to Return toWeapon Selection
ore Sighting the AN/PAQ-4. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F) Adjust Device until aiming laser is centered on the dot-cross hair.
M68
Receiver Rail0.0/5.6U
ore Sighting the M68. Stabilize Weapon.. Aim CCO at the dot cross hair. Adjust the CCO until the laser bore light is centered on its dot.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
62/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 62
M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &TA31F (ACOG) (Page 1 of 3 Pages)
The Aiming Light is mounted on the front left-hand, topor right-hand rail using the Insight rail grabber bracket(NSN 5340-01-458-0990) when it is desired to keepthe Aiming Light as close as possible to the barrel.
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. For ease of installation install the grabber on therail first, then mount the device on the grabber.
2. Loosen the clamping knob (1) until the rail grabberhas sufficient space to fit over the left side rail (2).Hand Tighten the clamping knob (1).
3. Turn the ON/OFF Switch CCW to the #1
OFF/STORAGE position.
4. Position the Aiming Light on the bracket mounting rail. Hand tighten the Thumbscrew (3) to secure the AimingLight.
5. Install the remote switch (not shown) in a convenient location using the provided cable hangers.
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If howeverthe device is removed from the rail the operator must take note of the position at which the device was zeroed,
and return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows25m Fired Zero Offsets:
- Left Side Rail Mounting: 4.2 Squares Right; 8.6 Squares Up- Top Rail Mounting: 1.7 Squares Right; 1.8 Squares Up- Right Side Rail Mounting: 4.3 Squares Left; 3.4 Squares Up
10m Boresight Offsets:
- Left Side Rail Mounting: 4.3 cm Left; 4.2cm Down- Top Rail Mounting: 1.8 cm Left; 2.2 cm Up
- Right Side Rail Mounting: 4.3 cm Right; .7 cm Down See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.
See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click forNext Device
-
8/7/2019 SAIB Rifles & Carbines with ARS
63/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 63
M4/M16A4 MWSAN/PAQ-4C Using Insight Low Profile Rail Grabber &TA31F (ACOG) (Page 2 of 3 Pages)
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
CAUTIONHand tighten mounting hardware only. Using
tools to tighten mounting hardware coulddamage equipment.
NOTEThe ACOG sight mounts directly to the upper
receiver rail on top of the M4/M4A1 and M16A4using the integral mount/rail grabber.
1. Install sight assembly (1) on the upper receiver rail (2). Sight may be installed in any position on the upperreceiver rail. Make sure grabber edges area around mounting rail and torque bar is in slot. To ensure that sightassembly is secure, tighten knobs (3). Hand tighten only. Periodically check the knobs to insure that the sight isstill securely attached to the rail.
2. If the same sight (serial number is on battery compartment) is installed in the same position on the rail on thesame weapon, re-zeroing is not required.
Target offsets required to properly zero the device to the weapon are as follows:
10m Boresight Offsets: 0.0 cm Left/Right; 4.8 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets. See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
1
2
3
-
8/7/2019 SAIB Rifles & Carbines with ARS
64/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
10m Boresight M4/M16A4 MWSAN/PAQ-4C Using Insight Low ProfileRail Grabber & TA31F (ACOG) (Page 3 of 3 Pages)
AN/PAQ-4B/CLeft Rail4.3L/4.2D
AN/PAQ-4B/CTop Rail1.8L/2.2U
AN/PAQ-4B/CRight Rail4.3R/0.7D
Laser Bore Light0/0
Click to Return toWeapon Selection
ore Sighting the AN/PAQ-4. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F) Adjust Device until aiming laser is centered on the dot-cross hair.
ACOGReceiver Rail
0.0/4.8U
ore Sighting the TA31F (ACOG). Stabilize Weapon.. Align Laser Borelight on its dot Adjust ACOG until bottom of the chevron (300M) is centered on the dot-cross hair.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
65/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 65
M4/M16A4 MWSAN/PAS-13A/B(V)1/3 L/HWTS and AN/PEQ-2A Mounted(Page 1 of 3)
(See Annex B for Target Prep Instructions)
Install the AN/PAS-13(V)1 on the Modular WeaponSystem (2) using the sights rail grabber/mount (NSN
1240-01-490-0737, Part No. A3281312-1) (3).
NOTEProcedures outlined below pertain to either M4 or M4A1
variants.
NOTE
Although the AN/PAS-13(v)1, LWTS is depicted both theAN/PAS-A/B(V)2 or (V)3 M/HWTS may also be mountedon the weapon using the same methods described below.In order to mount the AN/PAS-A/B(V)2 or (V)3 M/HWTSthe unit armorer must first install a Spacer Kit, M4 (NSN
5340-01-502-7971) to the TWS.
WARNINGMake sure the weapon is CLEAR and on SAFE before proceeding.
1. Remove carrying handle (not shown) from rail (4) of weapon. Retain carrying handle.
2. Loosen the clamping knob (5) until the jaws move far enough apart to fit over the rail (4).
3. Select a slot on rail. Any slot may be used as long as rail grabber/mount does not hang over edge of rail. If theTWS is removed from the rail the operator must note the position at which the device was zeroed, and return thedevice to that position in order to retain zero.
4. Place rail grabber/mount on rail and tighten clamping knob (5) until two clicks are heard.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 Squares Left/Right; 4.5 Squares Down- AN/PAS-13A/B(V)3 (HWTS): 0.0 Squares Left/Right; 6.0 Squares Down
10m Boresight Offsets:- AN/PAS-13B(v)1 (LWTS): 0.0 cm Left/Right; 7.9 cm Up- AN/PAS-13A/B(V)3 (HWTS): 0.0 cm Left/Right; 9.4 cm Up
See Annex BSIGHT/ACCESSORY OPERATING INSTRUCTIONS for instructions on preparation of AN/PAS-13 targets.
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click forNext Device
-
8/7/2019 SAIB Rifles & Carbines with ARS
66/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 66
M4/M16A4 MWSAN/PAS-13A/B(V)1/3 L/HWTS and AN/PEQ-2A Mounted(Page 2 of 3 Pages)
The AN/PEQ-2A (1) is mounted on the front left side,top, or right side rail (2) using the Insight Rail Grabber
Bracket (NSN 5340-01-458-0990) (3).
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Mount the rail grabber to the AN/PEQ-2A using thethumbscrew (4) as shown.
2. Loosen the clamping knob (5) on the rail grabberuntil the rail grabber has sufficient space to fit over theleft side rail.
3. Position and tighten the Rail Grabber by turning theknob clockwise.
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
he device is removed from the rail the operator must take note of the position at which the device was zeroed, andreturn the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets:
- Left Side Rail Mounting: 5.0 Squared Right; 4.0 Squares Up- Top Rail Mounting: 2.0 Squares Left; 1.2 Squared Up- Right Side Rail Mounting: 0.5 Squares Left; 8.5 Squares Up
10m Boresight Offsets:
- Left Side Rail Mounting:Aiming: 4.5 cm Left; 1.0 cm DownFlood: 4.5 cm Left; 5.0 cm Down
- Top Rail Mounting:Aiming: 2.0 cm Right; 2.3 cm Up
Flood: 2.0 cm Left; 2.3 cm Up- Right Side Rail Mounting:Aiming: 4.5 cm Right; 4.4 cm DownFlood: 4.5 cm Right; 0.4 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
67/104
10m Boresight M4/M16A4 MWSAN/PAS-13A/B(V)1/3 L/HWTS andAN/PEQ-2A Mounted (Page 3 of 3 Pages)
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
AN/PAS-13A/B (V)3Receiver Rail
0.0/9.4UHeat Source/ Fingers
Bore Sighting the AN/PAS-13A/B (V)1/31. Stabilize Weapon.2. Place Thermal signature material or tips of fingers on gray circles.3. Aim between gray circles at cross-hair.4. Adjust AN/PAS-13A/B(V)1/3 until the bore light laser is centered on its dot.5. You MUST zero reticle in both wide and narrow field of view.
AN/PAS-13B (V)1Receiver Rail
0.0/7.9U
Heat Source/ Fingers
Click to Return toWeapon Selection
AN/PEQ-2A FloodRight Rail4.5R/0.4D
AN/PEQ-2A Aim
Right Rail4.5R, 4.4D
AN/PEQ-2A AimLeft Rail4.5L/1.0D
AN/PEQ-2A FloodLeft Rail4.5L/5.0D
AN/PEQ-2A FloodTop Rail2.0L/2.3U
AN/PEQ-2A AimTop Rail2.0R/2.3U
Bore Sighting the AN/PEQ-21. Stabilize Weapon.
2. Align Laser Borelight on its dot (See Annex F)3. Adjust Device until aiming laser is centered on the dot-cross hair.4. Adjust AN/PEQ-2A Flood Light until the laser is centered on the
designated dot.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
68/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 68
M4/M16A4 MWSwith AN/PEQ-2A AN/PVS-4A MTD(Page 1 of 3 Pages)
The AN/PEQ-2A (1) is mounted on the front left side,top, or right side rail (2) using the Insight Rail Grabber
Bracket (NSN 5340-01-458-0990) (3).
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Mount the rail grabber to the AN/PEQ-2A using thethumbscrew (4) as shown.
2. Loosen the clamping knob (5) on the rail grabberuntil the rail grabber has sufficient space to fit over theleft side rail.
3. Position and tighten the Rail Grabber by turning theknob clockwise.
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
he device is removed from the rail the operator must take note of the position at which the device was zeroed, andreturn the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets:
- Left Side Rail Mounting: 5.0 Squared Right; 4.0 Squares Up- Top Rail Mounting: 2.0 Squares Left; 1.2 Squared Up- Right Side Rail Mounting: 0.5 Squares Left; 8.5 Squares Up
10m Boresight Offsets:
- Left Side Rail Mounting:Aiming: 4.5 cm Left; 1.0 cm DownFlood: 4.5 cm Left; 5.0 cm Down
- Top Rail Mounting:Aiming: 2.0 cm Right; 2.3 cm Up
Flood: 2.0 cm Left; 2.3 cm Up- Right Side Rail Mounting:Aiming: 4.5 cm Right; 4.4 cm DownFlood: 4.5 cm Right; 0.4 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click fornext Device
-
8/7/2019 SAIB Rifles & Carbines with ARS
69/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 69
M4/M16A4 MWSwith AN/PEQ-2A AN/PVS-4A MTD(Page 2 of 3 Pages)
To mount the AN/PVS-4A to the MWS the unitArmorer must install a spacer (NSN 5365-01-
447-8991) and a rail grabber/mount (NSN 5340-01-449-8533).
1. Loosen two knobs (1) on carrying handle(2). Remove carrying handle from upperreceiver rail (3). Retain carrying handle.
2. Install spacer (5) on AN/PVS-4A (7) usingthe two screws provided. Attach railgrabber/mount (6) to the spacer (5) using thetwo screws provided. (Pre-assembled by UnitArmorer.)
3. Loosen the clamping knob (8) until sufficientspace exists to place the clamping jaws oneither side of the mounting rail (3). Tightenclamping knob (8) until two clicks are heard.
4. The AN/PVS-4A may be placed on theupper receiver rail in the most convenient slot forthe operator, as long as the rail grabber/mountdoes not extend beyond the rail.
5. If the AN/PVS-4A is removed the operator must take note of the position at which the device was zeroed, andeturn the device to that same position to insure zero is retained.
NOTEItem (6) is depicted upside down in order to clearly show the bar which must fit into one of the slots on the rail.
NOTEThe AN/PVS-4A may also be mounted on the M4 handle in the same manner as is used to mount on the handle
of the M16A2. Items 5 & 6 will not be required when using this method. Insure that the mounting knob is insertedinto the hole in the carrying handle at an angle, due to the smaller gap between the top and bottom of the handle
(item 2 above).
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: 0.0 Squares Left/Right; 4.4 Squares Down
10m Boresight Offsets: 0.0 cm Left/Right; .7.6 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.
See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
70/104
10m Boresight M4/M16A4 MWSwith AN/PEQ-2A AN/PVS-4A MTD(Page 3 of 3 Pages)
Click to Return toWeapon Selection
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
AN/PEQ-2A FloodRight Rail4.5R/0.4D
AN/PVS-4Receiver Rail
0.0/7.6U
Laser Bore Light0/0
AN/PEQ-2A AimRight Rail4.5R, 4.4D
AN/PEQ-2A AimLeft Rail4.5L/1.0D
AN/PEQ-2A Flood
Left Rail4.5L/5.0D
AN/PEQ-2A FloodTop Rail2.0L/2.3U
AN/PEQ-2A AimTop Rail
2.0R/2.3U
Bore Sighting the AN/PVS-4A1. Stabilize Weapon.2. Aim AN/PVS-4A at Cross Hair and adjust until the bore light strikes the Laser Borelight Dot.
Bore Sighting the AN/PEQ-21. Stabilize Weapon.2. Align Laser Borelight on its dot (See Annex F)3. Adjust Device until aiming laser is centered on the dot-cross hair.4. Adjust AN/PEQ-2A Flood Light until the laser is centered on the designated dot.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
71/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 71
M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber,AN/PVS-14, & M68 (Page 1 of 4 Pages)
The AN/PEQ-2A (1) is mounted on the front left side orright side rail (2) using the Insight Rail Grabber Bracket
(NSN 5340-01-458-0990) (3). The top rail is notavailable since the M68 will be mounted there in a
following step.
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Mount the rail grabber to the AN/PEQ-2A using thethumbscrew (4) as shown.
2. Loosen the clamping knob (5) on the rail grabberuntil the rail grabber has sufficient space to fit over the
left side rail.3. Position and tighten the Rail Grabber by turning theknob clockwise.
NOTEThe device may be placed on the left or right rail, wherever is most convenient for the operator. If however thedevice is removed from the rail the operator must take note of the position at which the device was zeroed, and
return the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets:
- Left Side Rail Mounting: 5.0 Squared Right; 4.0 Squares Up- Top Rail Mounting: 2.0 Squares Left; 1.2 Squared Up- Right Side Rail Mounting: 0.5 Squares Left; 8.5 Squares Up
10m Boresight Offsets:
- Left Side Rail Mounting:Aiming: 4.5 cm Left; 1.0 cm DownFlood: 4.5 cm Left; 5.0 cm Down
- Top Rail Mounting:Aiming: 2.0 cm Right; 2.3 cm UpFlood: 2.0 cm Left; 2.3 cm Up
- Right Side Rail Mounting:Aiming: 4.5 cm Right; 4.4 cm DownFlood: 4.5 cm Right; 0.4 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for NextDevice
-
8/7/2019 SAIB Rifles & Carbines with ARS
72/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 72
M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber,AN/PVS-14, & M68 (Page 2 of 4 Pages)
3. Loosen the clamping knob on the weapon mount. Position the weapon mount with the monocular onto theweapons mounting rail. Tighten by turning the clamping knob.
NOTEThere is a ratchet in the weapon mount that prevents over tightening of the clamp. Turn until the knob clicks.
4. Check the position of the monocular by holding the weapon in your normal firing position. Adjust the fore/aftposition of the monocular as necessary by loosening the clamping knob and repositioning the weapon mount onthe weapons mounting rail.
NOTEThe MNVD can be used in conjunction with a collimated dot aiming device mounted on the
forward mounting rail. The brightness control for the aiming device should be set at or near its minimum setting.
Perform the following procedures for weapon mounted operation:
1. Ensure that the batteries are installed per the Tech Manual.
2. Assemble the weapon mount to the monocular as per steps 1 and 2, above.
3. Mount the monocular with adapter onto the M16/M4 receiver rail per steps 3 and 4, above.
4. Rotate the diopter adjustment for the clearest view of the image intensifier screen.
5. Adjust the objective lens focus (Figure 2-1) while observing an object until the sharpest image is obtained.
Target offsets required to properly zero the device to the weapon are as follows: NA. The AN/PVS-14 must beused in conjunction with either a laser aiming device or a collimated dot aiming device to be used as a weaponaiming system.
Click for NextDevice
Perform the following procedure to install the weaponmount.
The MNVD is not a weapon sight, however, it can be
used in conjunction with a collimated dot sight or laseraiming device.
NOTEIt is recommended that the eyecup be replaced with the
eyeguard during weapon mounted use.
1. Orient the monocular and weapon mount as shownin Figure 2-16, Be sure to align the alignment boss onthe weapon mount with the alignment groove in themonocular.
2. Screw in the thumbscrew to secure the monocular tothe weapon mount.
-
8/7/2019 SAIB Rifles & Carbines with ARS
73/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 73
M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber,AN/PVS-14, & M68 (Page 3 of 4 Pages)
Click for BoreSight Target
1
2
3
CAUTIONHand tighten mounting hardware only. Using tools
to tighten mounting hardware could damageequipment.
NOTEThe AN/PVS-14 was previously mounted to the upper
receiver rail on top of the M4/M4A1 or M16A4.
1. The M68 is mounted on the hand guard top rail,immediately in front of the AN/PVS-14. Make sure thespacer has been installed before mounting M68 onM4/M4A1 or M16A4.
NOTEIf the same sight (serial number is on battery
compartment) is installed in the same position on the railon the same weapon, re-zeroing is not required.
2. Install sight assembly (1) on the hand guard top rail (2). Sight may be installed in any position on the rail.Make sure grabber edges area around mounting rail and torque bar is in slot. To ensure that sight assembly issecure, tighten torque knob (3) until it clicks two times. Hand tighten only.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: 0.0 Squares Left/Right; 1.5 Squares Down10m Boresight Offsets: 0.0 cm Left/Right; 5.6 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets. See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
-
8/7/2019 SAIB Rifles & Carbines with ARS
74/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
AN/PEQ-2A FloodRight Rail4.5R/0.4D
10m Boresight M4/M16A4 MWSAN/PEQ-2A Using Insight Low ProfileRail Grabber, AN/PVS-14, & M68 (Page 4 of 4 Pages)
Laser Bore Light0/0
AN/PEQ-2A AimRight Rail4.5R, 4.4D
AN/PEQ-2A AimLeft Rail4.5L/1.0D
AN/PEQ-2A Flood
Left Rail4.5L/5.0D
AN/PEQ-2A FloodTop Rail2.0L/2.3U
AN/PEQ-2A AimTop Rail
2.0R/2.3U
ore Sighting the AN/PEQ-2. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F). Adjust Device until aiming laser is centered on the dot-cross hair.. Adjust AN/PEQ-2A Flood Light until the laser is centered on the designated dot.
Click to Return toWeapon Selection
M68Receiver Rail
0.0/5.6U
ore Sighting the M68. Stabilize Weapon.. Aim CCO at the dot cross hair.
Adjust the CCO until the laser bore light is centered on its dot.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
75/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 75
M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber &M68 (Page 1 of 3 Pages)
The AN/PEQ-2A (1) is mounted on the front left side,top, or right side rail (2) using the Insight Rail Grabber
Bracket (NSN 5340-01-458-0990) (3).
WARNINGMake sure the weapon is CLEAR and on SAFE
before proceeding.
1. Mount the rail grabber to the AN/PEQ-2A using thethumbscrew (4) as shown.
2. Loosen the clamping knob (5) on the rail grabberuntil the rail grabber has sufficient space to fit over theleft side rail.
3. Position and tighten the Rail Grabber by turning theknob clockwise.
NOTEThe device may be placed on the top, left, or right rail, wherever is most convenient for the operator. If however
he device is removed from the rail the operator must take note of the position at which the device was zeroed, andreturn the device to that same position in order to insure that zero is retained.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets:
- Left Side Rail Mounting: 5.0 Squared Right; 4.0 Squares Up- Top Rail Mounting: 2.0 Squares Left; 1.2 Squared Up- Right Side Rail Mounting: 0.5 Squares Left; 8.5 Squares Up
10m Boresight Offsets:
- Left Side Rail Mounting:Aiming: 4.5 cm Left; 1.0 cm DownFlood: 4.5 cm Left; 5.0 cm Down
- Top Rail Mounting:Aiming: 2.0 cm Right; 2.3 cm Up
Flood: 2.0 cm Left; 2.3 cm Up- Right Side Rail Mounting:
Aiming: 4.5 cm Right; 4.4 cm DownFlood: 4.5 cm Right; 0.4 cm Down
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets.See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for NextDevice
-
8/7/2019 SAIB Rifles & Carbines with ARS
76/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 76
M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber &M68 (Page 2 of 3 Pages)
CAUTIONHand tighten mounting hardware only. Using tools
to tighten mounting hardware could damageequipment.
NOTEThe sight assembly mounts directly to the upper receiverrail on top of the M4/M4A1 and M16A4. The mount is not
required. Make sure the spacer has been installedbefore mounting M68 on M4/M4A1 or M16A4.
1. If the same sight (serial number is on batterycompartment) is installed in the same position on the railon the same weapon, re-zeroing is not required.
2. Install sight assembly (1) on the upper receiver rail(2). Sight may be installed in any position on the upperreceiver rail. Make sure grabber edges area aroundmounting rail and torque bar is in slot. To ensure thatsight assembly is secure, tighten torque knob (3) until itclicks two times. Hand tighten only.
Target offsets required to properly zero the device to the weapon are as follows:
25m Fired Zero Offsets: 0.0 Squares Left/Right; 1.5 Squares Down10m Boresight Offsets: 0.0 cm Left/Right; 5.6 cm Up
See Annex GOFFSET TARGET PREPARATION for instructions on how to prepare targets. See Annex HOFFSET TARGET SUMMARY for a complete table of all device offsets.
Click for BoreSight Target
-
8/7/2019 SAIB Rifles & Carbines with ARS
77/104
10m Bore Sight Target for 300m Zero--(14 Dec 2001)
AN/PEQ-2A FloodRight Rail4.5R/0.4D
10m Boresight M4/M16A4 MWSAN/PEQ-2A Using Insight Low ProfileRail Grabber & M68 (Page 3 of 3 Pages)
Laser Bore Light0/0
AN/PEQ-2A AimRight Rail4.5R, 4.4D
AN/PEQ-2A AimLeft Rail4.5L/1.0D
AN/PEQ-2A Flood
Left Rail4.5L/5.0D
AN/PEQ-2A FloodTop Rail2.0L/2.3U
AN/PEQ-2A AimTop Rail
2.0R/2.3U
ore Sighting the AN/PEQ-2. Stabilize Weapon.. Align Laser Borelight on its dot (See Annex F). Adjust Device until aiming laser is centered on the dot-cross hair.. Adjust AN/PEQ-2A Flood Light until the laser is centered on the designated dot.
Click to Return toWeapon Selection
M68Receiver Rail
0.0/5.6U
ore Sighting the M68. Stabilize Weapon.. Aim CCO at the dot cross hair.
Adjust the CCO until the laser bore light is centered on its dot.
Turn off Printer Scaling
-
8/7/2019 SAIB Rifles & Carbines with ARS
78/104Small Arms Integration Book-Rifle/Carbine with Adapter Rail System Page 78
M4/M16A4 MWSAN/PEQ-2A Using Insight Low Profile Rail Grabber &TA 31F (ACOG) (Page 1 of 3 Pages)
The AN/PEQ-2A (1) is mounted on the front left side(2), top, or right side rail using the Insight Rail Grabber
Bracket (NSN 5340-01-458-0990) (3).
WARNINGMake sure the weapon is CLEAR and on SAFEbefore proceeding.
1. Mount the rail grabber to the AN/PEQ-2A using thethumbscrew (4) as shown.
2. Loosen the clamping knob (5) on the rail grabberuntil the rail grabber has sufficient space to fit over theleft side rail.
3. Position and tighten the Rail Grabber by turning theknob cl