safety tips & warnings - Champion Chisel

The following recommendations should help to increase the life of the tool and also contributeto personal safety and better performance.

When using any tool, safety glasses, safety shoes, safety helmet, safety gloves and earplugs should be worn for full protection.

Always have a sure footing to give hammer proper support while operating and don’ttake chances.

To prevent damage to both tool and accessory, accessory must be held firmly againstthe work surface before tool is throttled.

Never use air tools for prying during use. If tool is being used properly, this action isnot necessary.

Never use dull tools as they will accomplish very little and could break from fatigue.

Proper reconditioning procedures should be followed to prevent premature breakage.

Hammer parts should always be kept in good repair. Worn bushings and pistonscause excessive shank wear on tools.

Warm tools prior to use when temperature is below freezing.

Whip hose assemblies can cause serious injury. Always check for damaged or loosehoses and fittings.

Always disconnect the air supply before changing chisels or dismantling the tool forservice or repair. For maximum safety we advise the installation of a shut-off valveat the end of the air line.

ssaaffeettyy ttiippss && wwaarrnniinnggss

Champion Chisel Works has an experienced service department for the repair and maintenance of air tools. Please call for complete details. Estimated repair costs will be provided upon request.

aaiirr ttooooll mmaaiinntteennaannccee && rreeppaaiirr

CChhiippppiinngg HHaammmmeerrss 22 -- 77RRiivveett BBuusstteerrss 88 -- 1111CCllaayy DDiiggggeerrss 1122 -- 1133PPaavveemmeenntt BBrreeaakkeerrss 1144 -- 1199RRoocckk DDrriillllss 2200 -- 2233RRaammmmeerrss 2244 -- 2299SSccaalleerrss 3300 -- 3333FFlloooorr SSccrraappeerrss 3344 -- 3377AAcccceessssoorriieess 3388

All prices are FOB Shipping Point.AAiirr TTooooll OOrrddeerrss::*Air Tool orders of $3,500 (net price) or more receive free freight.*Air Tool orders of $500 (net price) or more that include an additional $1,500 (net price) or more in Steelreceive free freight.SStteeeell OOrrddeerrss::$100 - $1,499 Customer Pays Total Freight$1,500 - $1,999 (net price) Customer Pays 1/2 Freight$2,000 + (net price) Freight PrepaidRReettuurrnnss::Items returned may be subject to a 20% restocking fee. Please call for details.

Champion Chisel Works, Inc. tools are warranted against defects in material and workmanship for 180days from date of purchase. Warranty applies only to new tools purchased through Champion ChiselWorks. It does not cover any tool that may have been abused or misused during operation. It doesnot cover normal wear and tear or air tools that are repaired or modified by anyone other than a rep-resentative of Champion Chisel Works. Air tools must be operated at 90 PSI to receive coverage ofthis warranty. No other warranty is implied or expressed in this catalog.

If an air tool is found to be defective within 180 days of purchase, please contact Champion ChiselWorks to receive an RMA number and instructions for returning the tool to Champion Chisel Worksfor inspection.

ttaabbllee ooff ccoonntteennttss

ffrreeiigghhtt ppoolliiccyy

lliimmiitteedd wwaarrrraannttyy

1

cchhaammppiioonn cchhiisseell wwoorrkkss iinncc.. 11--881155--553355--00664477 wwwwww..cchhaammppiioonncchhiisseell..ccoomm

CHIPPING HAMMERS

Champion Chisel Works 815-535-0647 www.ChampionChisel.com22

Additional accessories available on page 38.

.580 Hex Shank.580 Hex Shank2.6” StrokeModel AT-CHMNH

(.580” Hex Shank)

Model AT-CHMNR(.680” Round Shank)

Blows Per Minute ........................................................ 2750Stroke ..............................................................................2.6”Bore .................................................................................1.1”Shank Diameter .......................................... .580”H/.680”RLength .......................................................................12-1/2”Weight .........................................................................9.4 lbsAir Inlet Bushing .....................................................7/8”-24Avg. Air Consumption (90psi) ...................................17 cfmRecommended Oil Weight .............................SAE 10W20

.580 Hex Shank.580 Hex ShankAccessories

Part No. DescriptionCHR-1190MN Solid/Oval RetainerCHR-1190RMN Solid/Round RetainerCHR-1291MN Quick Change RetainerCHR-SPRING-MN Lock SpringCHR-SPRING-MNPL Lock Spring - PlasticHS-782412 7/8”-24 x 1/2” Hose Barb HS-3812 3/8” x 1/2” Hose Barb (optional)10-CH5P-010 7/8” to 3/8” Reducer (optional)WHA-6CH 6’ whip hose with HS-782412 swivel, coupling and ILO-S in-line oiler.

*Champion Chisel Works 4-Bolt mini chippinghammers are sold without retainers. To order a chipping hammer with a retainer and lock spring attached, please add the corresponding suffi x shown below to the model number of the tool. Suffi x Description -O Oval retainer & lock spring -R Round retainer & lock spring -QC Quick change retainer & lock spring

Examples: AT-CHMNR-O is a .680” round shank, 2.6” stroke tool with an oval retainer & lock spring attached. AT-CHMNR is a .680” round shank, 2.6” stroke tool without a retainer or lock spring.

10 lb Class4-Bolt Mini Chipping Hammer

CHIPPING HAMMERS

Champion Chisel Works 815-535-0647 www.ChampionChisel.com 33

Parts List***When ordering replacement parts, furnish the model & serial number of your tool.***

Index Part No. Description 1 10-CH5P-002 Trigger 2 10-CH5P-003 Roll Pin for Trigger 3 10-CH5P-030 Handle Complete 4 10-CH5P-004 Sleeve Th rottle Valve Pin 5 10-CH5P-005 Th rottle Valve O-Ring * 10-CH5P-006 Th rottle Valve Assembly (Incl. #5, 6 & 7) 6 10-CH5P-006A Th rottle Valve Pin 7 10-CH5P-006B Seat Th rottle Valve 8 10-CH5P-007 Th rottle Valve Spring 9 10-CH5P-009B O-Ring Al Bushing 10 10-CH5P-008 Air Inlet Nipple w/Screen 11 10-CH5P-020 Exhaust Defl ector 12 10-CH5P-022 Hex Bushing * 10-CH5P-023 Round Bushing 13 CHR-1190MN Solid Oval Retainer * CHR-1190RMN Solid Round Retainer * CHR-1291MN Quick Change Retainer 14 CHR-SPRING-MN Lock Spring 15 10-CH5P-028 Nyloc Nut (Requires 4) 16 10-CH5P-029 Washer (Requires 4) 17 10-CH5P-021 Spacer Vibration (Requires 4) 18 10-CH5P-019 Barrel Flange 19 10-CH5P-017 Barrel 20 10-CH5P-016 Piston 21 10-CH5P-014 Valve Lid Lower 22 10-CH5P-013 Valve 23 10-CH5P-012 Valve Case 24 10-CH5P-015 Dowel Pin 25 10-CH5P-011 Valve Lid Upper 26 10-CH5P-027 Button Head Cap Screw*Not shown in parts diagram.

10 lb Class4-Bolt Mini Chipping Hammer

**CChhaammppiioonn CChhiisseell WWoorrkkss 44--BBoolltt cclloosseedd hhaannddllee cchhiippppiinngg hhaammmmeerrssaarree ssoolldd wwiitthhoouutt rreettaaiinneerrss.. TToo oorrddeerr aa cchhiippppiinngg hhaammmmeerr wwiitthh aarreettaaiinneerr aanndd lloocckk sspprriinngg aattttaacchheedd,, pplleeaassee aadddd tthhee ccoorrrreessppoonnddiinngg ssuuffffiixx sshhoowwnn bbeellooww ttoo tthhee mmooddeell nnuummbbeerr ooff tthhee gguunn..

Examples:AT-CH4R-R is a .680” round shank, 4” stroke gun with a round retainer& lock spring included. AT-CH4R is a .680” round shank, 4” stroke gun without aretainer or lock spring.

Suffix Description-O Oval retainer & lock spring-R Round retainer & lock spring

-QC Quick change ball type round retainer & lock spring

cchhiippppiinngg hhaammmmeerrss1122 -- 1155 llbb ccllaassss

44-- bboolltt cclloosseedd hhaannddllee


22”” ssttrrookkee

4

Blows Per Minute . . . . . . . . . . . . . . . . . . . . 2300Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1/8”Shank Diameter . . . . . . . . . . . . . .580”H/.680”RLength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14”Weight(Steel) . . . . . . . . . . . . . . . . . . . . . . 16 lbsAir Inlet Bushing . . . . . . . . . . . . . . . . . . . . . 7/8”Avg.Air Consumption (90 PSI) . . . . . . . . 30.5 cfmRecommended Oil Weight . . . . . .SAE 10 W 20


Blows Per Minute . . . . . . . . . . . . . . . . . . . . 2200Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1/8”Shank Diameter . . . . . . . . . . . . . .580”H/.680”RLength . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.25”Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 lbsAir Inlet Bushing . . . . . . . . . . . . . . . . . . . . . 7/8”Avg.Air Consumption (90 PSI) . . . . . . . . . 32 cfmRecommended Oil Weight . . . . . .SAE 10 W 20


Blows Per Minute . . . . . . . . . . . . . . . . . . . . 1800Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1/8”Shank Diameter . . . . . . . . . . . . . .580”H/.680”RLength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17”Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 lbsAir Inlet Bushing . . . . . . . . . . . . . . . . . . . . . 7/8”Avg.Air Consumption (90 PSI) . . . . . . . . . 35 cfmRecommended Oil Weight . . . . . .SAE 10 W 20

QQuuiicckk CChhaannggee RReettaaiinneerrSSoolliidd RReettaaiinneerr LLoocckk SSpprriinngg AAiirr IInnlleett HHoossee SSwwiivveell

WWhhiipp HHoossee AAsssseemmbbllyy

MMooddeell AATT--CCHH44HH(.580” Hex Shank)

MMooddeell AATT--CCHH44RR(.680” Round Shank)

Additional accessories available - see page 38.

PPaarrtt NNoo.. DDeessccrriippttiioonnCHR-1190SUL Solid/Taper/Oval CHR-1291SUL Quick Change/Taper CHR-SPRING Lock Spring CHR-QCKIT Quick Change Retainer Repair Kit

(1 Spring, 1 Lock Ring, 6 Ball Bearings)HS-782412 7/8”-24 UNC x 1/2” Hose Barb WHA-6CH 6’ whip hose assembly with HS-782412

swivel, coupling and ILO-S in line oiler.





aacccceessssoorriieess



RIVET BUSTERS


Part No. DescriptionRBP-RB2104 Rubber BumperRBP-UB2102 Urethane BumperRBP-US2101 Upper SleeveRBP-LS2103 Lower SleeveRBP-LS2103S Split Lower SleeveRBP-RS2194 Retainer SpringRBR-6085 RetainerHS-1212 1/2” x 1/2” Hose Barb

.580 Hex Shank.580 Hex Shank6” StrokeModel AT-RBA06

Blows Per Minute ........................................................ 1560Stroke .................................................................................6”Bore .............................................................................1.418”Length ..............................................................................17”Weight ..........................................................................23 lbsAir Inlet Bushing .......................................................... 7/8”Avg. Air Consumption (90psi) ...................................40 cfmRecommended Oil Weight .............................SAE 10W20

20 lb ClassClosed Handle

PSplit Lower SleeveLower Sleeve

Upper Sleeve

Bumper

Spring Retainer Hose Swivel

bschuldt

Typewritten Text

bschuldt

Typewritten Text


RIVET BUSTERS20 lb Class

Closed Handle

*Not shown in parts diagram.

Index Part No. Description 13 10-RB1P-013 Push Rod 14 10-RB1P-014 Th rottle Valve 15 10-RB1P-015 Th rottle Valve Stem 16 10-RB1P-016 Th rottle Valve Spring 17 10-RB1P-017 Air Inlet O-Ring 18 10-RB1P-018 Air Inlet 20 10-RB1P-020 Muffl er 22 RBP-US2101 Upper Sleeve Bushing 23 RBP-LS2103 Lower Sleeve Bushing 24 RBP-UB2102 Retainer Bumper 25 RBR-6085 Retainer 26 RBP-RS2194 Retainer Spring


Index Part No. Description 1 10-RB1P-001 Cylinder 2 10-RB1P-002 Cylinder O-Ring (Requires 2) 3 10-RB1P-003 Piston 4 10-RB1P-004 Valve Disc 5 10-RB1P-005 Valve Plater Upper 6 10-RB1P-006 Valve Plate Lower 7 10-RB1P-007 Dowel Pin (Requires 2) 8 10-RB1P-008 Packing Ring (Requires 2) 9 10-RB1P-009 Handle Bare * 10-RB1P-021 Handle Complete 10 10-RB1P-010 Th rottle Lever 11 10-RB1P-011 Th rottle Lever Pin 12 10-RB1P-012 Push Rod O-Ring



RIVET BUSTERS




Blows Per Minute ........................................................ 1140Stroke .................................................................................8”Bore ...........................................................................1-3/16”Length ...........................................................................22.5”Weight ..........................................................................30 lbsAir Inlet Bushing .......................................................... 1/2”Avg. Air Consumption (90psi) ...................................44 cfmRecommended Oil Weight .............................SAE 10W20


Blows Per Minute ...........................................................850Stroke ...............................................................................11”Bore ...........................................................................1-3/16”Length ...........................................................................25.5”Weight ..........................................................................33 lbsAir Inlet Bushing .......................................................... 1/2”Avg. Air Consumption (90psi) ...................................50 cfmRecommended Oil Weight .............................SAE 10W20

30 & 40 lb ClassClosed Handle


Upper Sleeve

Bumper



RIVET BUSTERS30 & 40 lb ClassClosed Handle


Index Part No. Description 16 10-RB1L-002 8” Barrel * 10-RB1M-004 11” Barrel 17 10-RB1N-001 8” Piston * 10-RB1M-002 11” Piston 18 10-RB1J-008 Handle Lock Ring 19 10-RB1J-011 Handle Lock Spring 20 10-RB1J-001 Handle Bushing (screened) * 10-RB1H-006 Exhaust Defl ector 22 RBP-US2101 Upper Sleeve Bushing 23 RBP-LS2103 Lower Sleeve Bushing 24 RBP-UB2102 Retainer Bumper (urethane) * RBP-RB2104 Retainer Bumper (rubber) 25 RBR-6085 Retainer 26 RBP-RS2194 Retainer Spring 27 10-RB1J-012 Muffl er Clamp 29 10-RB1J-013 Muffl er


Index Part No. Description 1 10-RB1G-013 Bare Handle * 10-RB1G-014 Complete Handle 3 10-RB1G-001 Th rottle Lever 4 10-RB1G-008 Th rottle Lever Pin 5 10-RB1G-007 Th rottle Valve 6 10-RB1G-011 Th rottle Valve Bushing 6A 10-RB1G-005 Th rottle Valve Bushing O-Ring 6B 10-RB1J-002 Th rottle Valve O-Ring 7 10-RB1J-003 Th rottle Valve Spring 8 10-RB1H-010 Th rottle Valve Plug 9 10-RB1G-006 Push Pin 10 10-RB1G-009 Push Pin Bushing 11 10-RB1J-005 Valve Box 12 10-RB1J-006 Valve 13 10-RB1J-009 Valve Cover Front * 10-RB1J-010 Valve Assembly 15 10-RB1J-007 Valve Dowel Pin





.580 Hex Shank.580 Hex Shank8” StrokeModel AT-RBA08-OH

Blows Per Minute ........................................................ 1140Stroke .................................................................................8”Bore ...........................................................................1-3/16”Length ...........................................................................22.5”Weight ..........................................................................30 lbsAir Inlet Bushing .......................................................... 1/2”Avg. Air Consumption (90psi) ...................................44 cfmRecommended Oil Weight .............................SAE 10W20

.580 Hex Shank.580 Hex Shank11” StrokeModel AT-RBA11-OH

Blows Per Minute ...........................................................850Stroke ...............................................................................11”Bore ...........................................................................1-3/16”Length ...........................................................................25.5”Weight ..........................................................................33 lbsAir Inlet Bushing .......................................................... 1/2”Avg. Air Consumption (90psi) ...................................50 cfmRecommended Oil Weight .............................SAE 10W20

RIVET BUSTERS30 & 40 lb Class

Open Handle


Upper Sleeve

Bumper



RIVET BUSTERS30 & 40 lb Class

Open Handle


Index Part No. Description 16 10-RB1L-002 8” Barrel * 10-RB1M-004 11” Barrel 17 10-RB1N-001 8” Piston * 10-RB1M-002 11” Piston 18 10-RB1J-008 Handle Lock Ring 19 10-RB1J-011 Handle Lock Spring 20 10-RB1J-001 Handle Bushing (screened) 21 10-RB1H-006 Exhaust Defl ector 22 RBP-US2101 Upper Sleeve Bushing 23 RBP-LS2103 Lower Sleeve Bushing 24 RBP-UB2102 Retainer Bumper (urethane) * RBP-RB2104 Retainer Bumper (rubber) 25 RBR-6085 Retainer 26 RBP-RS2194 Retainer Spring * 10-RB1J-013 Muffl er * 10-RB1J-012 Muffl er Clamp

Index Part No. Description 1 10-RB1H-008 Bare Handle * 10-RB1H-009 Complete Handle 3 10-RB1H-001 Th rottle Lever 4 10-RB1H-002 Th rottle Lever Pin 5 10-RB1H-005 Th rottle Valve 6 10-RB1H-003 Th rottle Valve Bushing * 10-RB1J-002 Th rottle Valve O-Ring 7 10-RB1J-003 Th rottle Valve Spring 8 10-RB1H-010 Th rottle Valve Plug 9 10-RB1H-004 Push Pin 10 10-RB1H-007 Push Pin Bushing 11 10-RB1J-005 Valve Box 12 10-RB1J-006 Valve 13 10-RB1J-009 Valve Cover Front * 10-RB1J-010 Valve Assembly 15 10-RB1J-007 Valve Dowel Pin


ccllaayy ddiiggggeerrss3300 llbb ccllaassss


12

77//88”” xx 33--11//44””

Blows Per Minute . . . . . . . . . . . . . . . . . 1550Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 3.375”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3/4”Length . . . . . . . . . . . . . . . . . . . . . . . . . . . 23”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 30 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/8”Avg.Air Consumption (90 PSI) . . . . . . . 49 cfmRecommended Oil Weight . . .SAE 15 W 50

MMooddeell AATT--CCDD3300--7788

11”” xx 44--11//44””

Blows Per Minute . . . . . . . . . . . . . . . . . 1550Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 3.375”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3/4”Length . . . . . . . . . . . . . . . . . . . . . . . . . . . 23”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 30 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/8”Avg.Air Consumption (90 PSI) . . . . . . . 49 cfmRecommended Oil Weight . . .SAE 15 W 50

MMooddeell AATT--CCDD3300--11

THOR STYLE

13


ccllaayy ddiiggggeerrss3300 llbb ccllaassss

**NNOOTT SSHHOOWWNN IINN PPAARRTTSS DDIIAAGGRRAAMM

PPaarrttss LLiisstt******WWHHEENN OORRDDEERRIINNGG RREEPPLLAACCEEMMEENNTT PPAARRTTSS,, FFUURRNNIISSHH TTHHEE MMOODDEELL && SSEERRIIAALL NNUUMMBBEERR OOFF YYOOUURR TTOOOOLL******

IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN21 10-PB1G-015 RETAINER BOLT NUT22 10-PB1G-016 RETAINER BOLT LOCK WASHER23 10-PB1G-017 PLUNGER SPRING24 10-PB1G-018 RETAINER PLUNGER25 10-PB1G-019 FRONTHEAD BARE* 10-PB1G-020 FRONTHEAD COMPLETE

26 10-PB1G-21 RETAINER BOLT27 10-PB1G-022 BOLT NUT (5)* 10-PB1G-023 BOLT WASHER (5)

28 10-PB1G-024 STEEL RETAINER29 10-PB1G-025 CYLINDER PLUGS (3)30 10-PB1G-026 AUTOMATIC VALVE31 10-PB1G-027 VALVE GUIDE32 10-PB1A-005 THROTTLE VALVE BUSHING33 10-PB1A-006 THROTTLE VALVE34 10-PB1A-007 THROTTLE VALVE SPRING35 10-PB1A-008 THROTTLE VALVE CAP36 10-PB1A-009 THROTTLE VALVE PUSH PIN37 10-PB1A-010 PUSH PIN BUSHING38 10-PB1G-028 AIR INLET SWIVEL* 10-PB1G-029 MUFFLER ASSEMBLY COMPLETE

IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-PB1G-001 AIR INLET SWIVEL NUT2 10-PB1E-001 OIL CONTROL PLUG3 10-PB1E-002 OIL CONTROL FELT4 10-PB1G-002 INLET SWIVEL O-RING5 10-PB1G-003 INLET SWIVEL SPRING6 10-PB1G-004 AIR INLET SCREEN7 10-PB1A-001 BACKHEAD (INCL. 10-PB1A-010 & 10-PB1A-005)* 10-PB1A-002 BACKHEAD COMPLETE8 10-PB1A-003 THROTTLE LEVER9 10-PB1A-004 THROTTLE LEVER PIN10 10-PB1G-005 OIL PLUG11 10-PB1G-006 BACKHEAD SPRING12 10-PB1G-007 VALVE DOWEL13 10-PB1G-008 VALVE CHEST14 10-PB1G-009 VALVE SEAT15 10-PB1G-010 PISTON16 10-PB1G-011 BACKHEAD BOLT (4)17 10-PB1G-012 CYLINDER18 10-PB1K-001 CHUCK BUSHING 7/8” X 3-1/4”* 10-PB1L-001 CHUCK BUSHING 1” X 4-1/4”

19 10-PB1G-013 FRONTHEAD BOLT20 10-PB1G-014 RETAINER BOLT BUSHING

ppaavveemmeenntt bbrreeaakkeerrss3300 llbb ccllaassss


14

77//88”” xx 33--11//44””

Blows Per Minute . . . . . . . . . . . . . . . . . 1550Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 3.375”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3/4”Length . . . . . . . . . . . . . . . . . . . . . . . . . . 22.5”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 34 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/8”Avg.Air Consumption (90 PSI) . . . . . . . 49 cfmRecommended Oil Weight . . .SAE 15 W 50

MMooddeell AATT--PPBB3300--7788

11”” xx 44--11//44””

Blows Per Minute . . . . . . . . . . . . . . . . . 1550Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 3.375”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3/4”Length . . . . . . . . . . . . . . . . . . . . . . . . . . 22.5”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 34 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/8”Avg.Air Consumption (90 PSI) . . . . . . . 49 cfmRecommended Oil Weight . . .SAE 15 W 50


THOR STYLE

15



IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN19 10-PB1G-016 RETAINER BOLT LOCK WASHER20 10-PB1G-017 RETAINER PLUNGER SPRING21 10-PB1G-018 RETAINER PLUNGER22 10-PB1G-019 FRONTHEAD* 10-PB1G-020 FRONTHEAD COMPLETE

23 10-PB1G-021 RETAINER BOLT24 10-PB1G-024 STEEL RETAINER - FORGED25 10-PB1G-025 CYLINDER PLUG (3)26 10-PB1G-009 VALVE SEAT27 10-PB1B-003 THROTTLE VALVE SPRING28 10-PB1F-004 THROTTLE VALVE29 10-PB1F-005 THROTTLE VALVE SLEEVE30 10-PB1E-001 OIL CONTROL PLUG31 10-PB1G-002 INLET SWIVEL O-RING32 10-PB1G-001 AIR INLET SWIVEL NUT33 10-PB1G-028 AIR INLET SWIVEL34 10-PB1G-003 INLET SWIVEL SPRING35 10-PB1G-004 AIR INLET SCREEN36 10-PB1E-002 OIL CONTROL FELT* 10-PB1G-029 MUFFLER* 10-PB1J-001 PLUG



IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-PB1F-001 RUBBER GRIP (2)2 10-PB1F-002 THROTTLE LEVER3 10-PB1G-022 BOLT NUT (5)* 10-PB1G-023 BOLT WASHER (5)4 10-PB1F-003 THROTTLE LEVER PIN (2)5 10-PB1B-001 BACKHEAD (INCL. 10-PB1F-005)* 10-PB1B-002 BACKHEAD COMPLETE6 10-PB1G-005 OIL PLUG7 10-PB1G-006 BACKHEAD SPRING8 10-PB1G-007 VALVE DOWEL9 10-PB1G-027 VALVE GUIDE10 10-PB1G-008 VALVE CHEST11 10-PB1G-026 AUTOMATIC VALVE12 10-PB1G-010 PISTON13 10-PB1G-011 BACKHEAD BOLT (4)14 10-PB1G-012 CYLINDER15 10-PB1L-001 CHUCK BUSHING 1” X 4-1/4” HEX* 10-PB1K-001 CHUCK BUSHING 7/8” X 3-1/4” HEX

16 10-PB1G-013 FRONTHEAD BOLT17 10-PB1G-014 RETAINER BOLT BUSHING18 10-PB1G-015 RETAINER BOLT NUT



16

11--11//88”” xx 66””

Blows Per Minute . . . . . . . . . . . . . . . . . 1400Stroke . . . . . . . . . . . . . . . . . . . . . . . . 4.0937”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1/4”Length . . . . . . . . . . . . . . . . . . . . . . . . 25.625”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 67 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/4”Avg.Air Consumption (90 PSI) . . . . . . . 59 cfmRecommended Oil Weight . . .SAE 15 W 50


11--11//44”” xx 66””

Blows Per Minute . . . . . . . . . . . . . . . . . 1400Stroke . . . . . . . . . . . . . . . . . . . . . . . . 4.0937”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1/4”Length . . . . . . . . . . . . . . . . . . . . . . . . 25.625”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 67 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/4”Avg.Air Consumption (90 PSI) . . . . . . . 59 cfmRecommended Oil Weight . . .SAE 15 W 50


THOR STYLE

17





IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN24 10-PB1C-011 FRONTHEAD BARE* 10-PB1C-012 FRONTHEAD SPIKE DRIVER

25 10-PB1H-014 STEEL RETAINER BOLT NUT26 10-PB1H-015 STEEL RETAINER LOCK WASHER27 10-PB1H-016 STEEL RETAINER - FORGED28 10-PB1C-013 TAPPET29 10-PB1C-014 TAPPET SEAT30 10-PB1H-017 AIR INLET SWIVEL O-RING31 10-PB1H-018 AIR INLET SWIVEL32 10-PB1H-019 SWIVEL NUT O-RING33 10-PB1H-020 AIR INLET SWIVEL NUT34 10-PB1H-021 AIR INLET SCREEN35 10-PB1H-022 CYLINDER PLUGS (5)36 10-PB1C-015 VALVE SEAT37 10-PB1H-023 AUTOMATIC VALVE38 10-PB1C-016 VALVE CHEST39 10-PB1H-024 VALVE DOWEL PIN40 10-PB1H-025 BACKHEAD PLUNGER41 10-PB1H-026 THROTTLE VALVE SPRING42 10-PB1F-004 THROTTLE VALVE* 10-PB1H-027 THROTTLE O-RING

43 10-PB1F-005 THROTTLE VALVE SLEEVE44 10-PB1E-001 OIL CONTROL PLUG* 10-PB1M-001 FRONTHEAD WITH 1-1/8” HEX BUSHING* 10-PB1N-001 FRONTHEAD WITH 1-1/4” HEX BUSHING* 10-PB1M-002 FRONTHEAD ASSEMBLY WITH 1-1/8” HEX* 10-PB1N-002 FRONTHEAD ASSEMBLY WITH 1-1/4” HEX* 10-PB1C-017 MUFFLER ASSEMBLY

IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-PB1F-002 THROTTLE LEVER2 10-PB1F-003 THROTTLE LEVER PIN (2)3 10-PB1E-002 OIL CONTROL FELT4 10-PB1H-001 BACKHEAD BOLT NUT (4)5 10-PB1H-002 BACKHEAD BOLT LOCK WASHER (4)6 10-PB1C-001 BACKHEAD BARE (INCL. 10-PB1F-005)* 10-PB1C-002 BACKHEAD ASSEMBLY COMPLETE7 10-PB1F-001 RUBBER GRIP (2)8 10-PB1C-004 OIL RESERVOIR PLUG9 10-PB1C-005 BACKHEAD O-RING10 10-PB1H-003 BACKHEAD PLUNGER SPRING* 10-PB1H-004 BACKHEAD VALVE PORT O-RING

11 10-PB1C-006 VALVE GUIDE12 10-PB1C-007 BACKHEAD BOLT (4)13 10-PB1C-008 FRONTHEAD BOLT (2)14 10-PB1C-009 CYLINDER15 10-PB1C-010 PISTON16 10-PB1O-001 FRONTHEAD BUSHING 1-1/8” HEX* 10-PB1P-001 FRONTHEAD BUSHING 1-1/4” HEX

17 10-PB1H-005 FRONTHEAD BOLT SPRING (2)* 10-PB1H-006 SPIKE DRIVER DOLLY

18 10-PB1H-007 FRONTHEAD BOLT LOCK WASHER (2)19 10-PB1H-008 FRONTHEAD BOLT NUT (2)20 10-PB1H-009 STEEL RETAINER BOLT21 10-PB1H-010 RETAINER BOLT BUSHING - RUBBER (2)* 10-PB1H-011 RETAINER BOLT BUSHING - STEEL (2)

22 10-PB1H-012 RETAINER PLUNGER SPRING23 10-PB1H-013 STEEL RETAINER PLUNGER



18

11--11//88”” xx 66””

Blows Per Minute . . . . . . . . . . . . . . . . . 1250Stroke . . . . . . . . . . . . . . . . . . . . . . . . 6.0625”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5/8”Length . . . . . . . . . . . . . . . . . . . . . . . . . 28.75”Weight . . . . . . . . . . . . . . . . . . . . . . . . 92.5 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/4”Avg.Air Consumption (90 PSI) . . . . . . . 75 cfmRecommended Oil Weight . . .SAE 15 W 50


11--11//44”” xx 66””

Blows Per Minute . . . . . . . . . . . . . . . . . 1250Stroke . . . . . . . . . . . . . . . . . . . . . . . . 6.0625”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5/8”Length . . . . . . . . . . . . . . . . . . . . . . . . . 28.75”Weight . . . . . . . . . . . . . . . . . . . . . . . . 92.5 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/4”Avg.Air Consumption (90 PSI) . . . . . . . 75 cfmRecommended Oil Weight . . .SAE 15 W 50


THOR STYLE

19





IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN24 10-PB1D-010 FRONTHEAD BARE* 10-PB1D-011 FRONTHEAD SPIKE DRIVER

25 10-PB1H-014 STEEL RETAINER BOLT NUT26 10-PB1H-015 STEEL RETAINER LOCK WASHER27 10-PB1H-016 STEEL RETAINER - FORGED28 10-PB1D-012 TAPPET29 10-PB1D-013 TAPPET SEAT30 10-PB1H-017 AIR INLET SWIVEL O-RING31 10-PB1H-018 AIR INLET SWIVEL32 10-PB1H-019 SWIVEL NUT O-RING33 10-PB1H-020 AIR INLET SWIVEL NUT34 10-PB1H-021 AIR INLET SCREEN35 10-PB1H-022 CYLINDER PLUGS (5)36 10-PB1D-014 VALVE SEAT37 10-PB1H-023 AUTOMATIC VALVE38 10-PB1D-015 VALVE CHEST39 10-PB1H-024 VALVE DOWEL PIN40 10-PB1H-025 BACKHEAD PLUNGER41 10-PB1F-005 THROTTLE VALVE SLEEVE42 10-PB1H-026 THROTTLE VALVE SPRING43 10-PB1F-004 THROTTLE VALVE* 10-PB1H-027 THROTTLE O-RING

44 10-PB1E-001 OIL CONTROL PLUG* 10-PB1R-001 FRONTHEAD WITH 1-1/4” HEX BUSHING* 10-PB1Q-001 FRONTHEAD WITH 1-1/8” HEX BUSHING* 10-PB1R-002 FRONTHEAD ASSEMBLY WITH 1-1/4” HEX* 10-PB1Q-002 FRONTHEAD ASSEMBLY WITH 1-1/8” HEX* 10-PB1D-016 OIL TANK PLUG

IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-PB1F-002 THROTTLE LEVER2 10-PB1F-003 THROTTLE LEVER PIN (2)3 10-PB1D-001 OIL RESERVOIR PLUG4 10-PB1E-002 OIL CONTROL FELT5 10-PB1H-001 BACKHEAD BOLT NUT (4)6 10-PB1H-002 BACKHEAD BOLT LOCK WASHER (4)7 10-PB1D-002 BACKHEAD BARE (INCL. 10-PB1F-005)* 10-PB1D-003 BACKHEAD ASSEMBLY COMPLETE8 10-PB1F-001 RUBBER GRIP (2)9 10-PB1D-004 BACKHEAD O-RING* 10-PB1H-004 BACKHEAD VALVE PORT O-RING

10 10-PB1H-003 BACKHEAD PLUNGER SPRING11 10-PB1D-005 VALVE GUIDE12 10-PB1D-006 BACKHEAD BOLT (4)13 10-PB1D-007 FRONTHEAD BOLT(2)14 10-PB1D-008 CYLINDER15 10-PB1D-009 PISTON16 10-PB1P-001 FRONTHEAD BUSHING 1-1/8” HEX* 10-PB1O-001 FRONTHEAD BUSHING 1-1/4” HEX

17 10-PB1H-005 FRONTHEAD BOLT SPRING (2)* 10-PB1H-006 SPIKE DRIVER DOLLY

18 10-PB1H-007 FRONTHEAD BOLT LOCK WASHER (2)19 10-PB1H-008 FRONTHEAD BOLT NUT (2)20 10-PB1H-009 STEEL RETAINER BOLT21 10-PB1H-010 RETAINER BOLT BUSHING - RUBBER (2)* 10-PB1H-011 RETAINER BOLT BUSHING - STEEL (2)

22 10-PB1H-012 RETAINER PLUNGER SPRING23 10-PB1H-013 STEEL RETAINER PLUNGER

rroocckk ddrriillllss3300 llbb ccllaassss


20

77//88”” xx 33--11//44””

Blows Per Minute . . . . . . . . . . . . . . . . . 2700Stroke . . . . . . . . . . . . . . . . . . . . . . . . 1.4375”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7/16”Length . . . . . . . . . . . . . . . . . . . . . . . . . . 19.5”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 29 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/4”Avg.Air Consumption (90 PSI) . . . . . . . 73 cfmRecommended Oil Weight . . .SAE 20 W 70

MMooddeell AATT--RRDD3300--7788331144

77//88”” xx 44--11//44””

Blows Per Minute . . . . . . . . . . . . . . . . . 2700Stroke . . . . . . . . . . . . . . . . . . . . . . . . 1.4375”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7/16”Length . . . . . . . . . . . . . . . . . . . . . . . . . . 19.5”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 29 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/4”Avg.Air Consumption (90 PSI) . . . . . . . 73 cfmRecommended Oil Weight . . .SAE 20 W 70


****RRoocckk DDrriillllss aarree wwaatteerr ccoommppaattiibbllee wwiitthh aa ccoonnvveerrssiioonn kkiitt aavvaaiillaabbllee ffrroomm CChhaammppiioonn CChhiisseell WWoorrkkss.. PPlleeaassee ccaallll ffoorr mmoorree ddeettaaiillss..****

21





IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-RD1A-001 HANDLE GRIP (2)2 10-RD1A-002 HANDLE BOLT WASHER (2)3 10-RD1A-003 HANDLE BOLT NUT4 10-RD1A-004 AIR CONNECTION ELBOW5 10-RD1A-005 AIR CONNECTION O-RING6 10-RD1A-006 AIR CONNECTION NUT WASHER7 10-RD1A-007 THROTTLE VALVE PLUNGER8 10-RD1A-008 THROTTLE VALVE SPRING9 10-RD1A-009 AIR CONNECTION NUT WASHER10 10-RD1A-010 SWIVEL CONNECTION11 10-RD1A-011 THROTTLE VALVE12 10-RD1A-012 BACKHEAD-DRY13 10-RD1A-013 VALVE CHEST14 10-RD1A-014 AUTOMATIC VALVE15 10-RD1A-015 VALVE CHEST COVER16 10-RD1A-016 SIDE ROD (2)17 10-RD1A-017 SIDE ROD NUT18 10-RD1A-018 EXHAUST DEFLECTOR19 10-RD1A-019 CYLINDER20 10-RD1A-020 PAWL SPRING (2)21 10-RD1A-021 ROTATION PAWL (2)22 10-RD1A-022 STEEL RETAINER BOLT23 10-RD1A-023 STEEL RETAINER SCREW24 10-RD1A-024 STEEL RETAINER SPRING25 10-RD1A-025 STEEL RETAINER PLUNGER26 10-RD1A-026 STEEL RETAINER PACKING (2)27 10-RD1A-027 STEEL RETAINER28 10-RD1A-028 STEEL RETAINER PIN29 10-RD1A-029 STEEL RETAINER NUT30 10-RD1A-030 FRONTHEAD 3-1/4” SHANK* 10-RD1A-031 FRONTHEAD 4-1/4” SHANK

31 10-RD1A-032 FRONTHEAD LINER SMALL32 10-RD1A-033 FRONTHEAD LINER LARGE33 10-RD1A-034 SLEEVE BUSHING 7/8” HEX X 3-1/4”* 10-RD1A-035 SLEEVE BUSHING 7/8” HEX X 4-1/4”

34 10-RD1A-036 ROTATION SLEEVE 3-1/4”* 10-RD1A-037 ROTATION SLEEVE 4-1/4”

35 10-RD1A-038 SLEEVE NUT36 10-RD1A-039 RATCHET RING RIFLE NUT37 10-RD1A-040 FRONT WASHER38 10-RD1A-041 FRONT WASHER BUSHING39 10-RD1A-042 PISTON40 10-RD1A-043 VALVE CHEST COVER O-RING (2)41 10-RD1A-044 THROTTLE VALVE BOLT42 10-RD1A-045 THROTTLE VALVE HANDLE43 10-RD1A-046 THROTTLE BOLT LOCK WASHER44 10-RD1A-047 THROTTLE BOLT NUT45 10-RD1A-048 HANDLE BOLT46 10-RD1A-049 BLOW TUBE 47 10-RD1A-050 TUBE GASKET48 10-RD1A-051 TUBE GLAND GASKET49 10-RD1A-052 BLOW TUBE GLAND50 10-RD1A-053 RIGHT GRIP SUPPORT51 10-RD1A-054 CENTER GRIP52 10-RD1A-055 LEFT GRIP SUPPORT



22

77//88”” xx 44--11//44””

Blows Per Minute . . . . . . . . . . . . . . . . . 1800Stroke . . . . . . . . . . . . . . . . . . . . . . . . 2.5625”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5/8”Length . . . . . . . . . . . . . . . . . . . . . . . . . . . 24”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 59 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/4”Avg.Air Consumption (90 PSI) . . . . . . . 98 cfmRecommended Oil Weight . . .SAE 20 W 70


11”” xx 44--11//44””

Blows Per Minute . . . . . . . . . . . . . . . . . 1800Stroke . . . . . . . . . . . . . . . . . . . . . . . . 2.5625”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5/8”Length . . . . . . . . . . . . . . . . . . . . . . . . . . . 24”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 59 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/4”Avg.Air Consumption (90 PSI) . . . . . . . 98 cfmRecommended Oil Weight . . .SAE 20 W 70


GARDNER-DENVER STYLE

****RRoocckk DDrriillllss aarree wwaatteerr ccoommppaattiibbllee wwiitthh aa ccoonnvveerrssiioonn kkiitt aavvaaiillaabbllee ffrroomm CChhaammppiioonn CChhiisseell WWoorrkkss.. PPlleeaassee ccaallll ffoorr mmoorree ddeettaaiillss..****

23





IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-RD1B-001 AIR INLET SWIVEL2 10-RD1B-002 SWIVEL NUT3 10-RD1B-003 SWIVEL RETAINER4 10-RD1B-004 THROTTLE VALVE5 10-RD1B-005 PAWL PLUNGER (4)6 10-RD1B-006 PAWL NON-REVERSIBLE (4)7 10-RD1B-007 PAWL SPRING COIL (4)8 10-RD1B-008 RIFLE BAR9 10-RD1B-009 RATCHET RING10 10-RD1B-010 VALVE GUIDE11 10-RD1B-011 REAR VALVE CHEST12 10-RD1B-012 AUTOMATIC VALVE13 10-RD1B-013 FRONT VALVE CHEST14 10-RD1B-014 RIFLE NUT15 10-RD1B-015 PISTON16 10-RD1B-016 OIL FILLER PLUG17 10-RD1B-017 EXHAUST VALVE PIN18 10-RD1B-018 EXHAUST VALVE WASHER19 10-RD1B-019 EXHAUST VALVE SPRING20 10-RD1B-020 SIDE ROD21 10-RD1B-021 SIDE ROD SPACER (2)22 10-RD1B-022 SIDE ROD NUT - LONG (2)23 10-RD1B-023 SIDE ROD LOCK WASHER (2)24 10-RD1B-024 SIDE ROD NUT - SHORT (2)25 10-RD1B-025 RETAINER SPRING26 10-RD1B-026 RETAINER PIVOT27 10-RD1B-027 STEEL RETAINER 1” X 4-1/4”28 10-RD1B-028 RETAINER YOKE29 10-RD1B-029 FRONTHEAD 1” X 4-1/4”

IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN30 10-RD1B-030 YOKE SPRING (2)31 10-RD1B-031 YOKE NUT - NYLON INSERT (2)32 10-RD1B-032 CHUCK BUSHING 7/8” X 4-1/4”* 10-RD1B-033 CHUCK BUSHING 1” X 4-1/4”

33 10-RD1B-034 CHUCK DRIVER 1” X 4-1/4”34 10-RD1B-035 CYLINDER BUSHING35 10-RD1B-036 EXHAUST VALVE36 10-RD1B-037 CYLINDER37 10-RD1B-038 RATCHET DOWEL PIN38 10-RD1B-039 BLOW TUBE* 10-RD1B-040 BACKHEAD WITH BUSHING

39 10-RD1B-041 BACKHEAD BUSHING40 10-RD1B-042 THROTTLE VALVE HANDLE BOLT41 10-RD1B-043 THROTTLE VALVE HANDLE42 10-RD1B-044 THROTTLE VALVE HANDLE WASHER43 10-RD1B-045 THROTTLE VALVE HANDLE BOLT NUT44 10-RD1B-046 BLOW TUBE WASHER45 10-RD1B-047 BLOW TUBE GLAND46 10-RD1B-048 HANDLE BOLT WASHER (2)47 10-RD1B-049 HANDLE GRIP COMPLETE (2)48 10-RD1B-050 HANDLE BOLT49 10-RD1B-051 HANDLE BOLT NUT50 10-RD1B-052 BLOW TUBE GASKET51 10-RD1B-053 BLOW TUBE RUBBER SEAL52 10-RD1B-054 DETENT PLUNGER53 10-RD1B-055 DETENT SPRING54 10-RD1B-056 SWIVEL WASHER55 10-RD1B-057 SWIVEL O-RING* 10-RD1B-058 MUFFLER


24

bbeenncchh rraammmmeerrss

22”” SSTTRROOKKEE

Blows Per Minute . . . . . . . . . . . . . . . . . 1725Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1”Length . . . . . . . . . . . . . . . . . . . . . . . . 16-1/2”Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 7 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/8”Avg.Air Consumption (90 PSI) . . . . . . . 13 cfmTaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . .802Min. Hose Size . . . . . . . . . . . . . . . . . . . . .1/2”Recommended Oil Weight . . .SAE 15 W 50

MMooddeell AATT--BBRR--22BBAA


Blows Per Minute . . . . . . . . . . . . . . . . . 1240Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1”Length . . . . . . . . . . . . . . . . . . . . . . . . 21-1/2”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 10 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/8”Avg.Air Consumption (90 PSI) . . . . . . . 19 cfmTaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . .802Min. Hose Size . . . . . . . . . . . . . . . . . . . . .1/2”Recommended Oil Weight . . .SAE 15 W 50

MMooddeell AATT--BBRR--11BBAA

****BBeenncchh RRaammmmeerrss aarree ssoolldd wwiitthh aa 22--11//22”” rruubbbbeerr bbuutttt****

TTooooll BBuuttttMMooddeell NNoo.. MMooddeell NNoo.. SSiizzee

AT-BR-2BA BRB-202-802 2-1/2”BRB-203-802 3-1/4”

AT-BR-1BA BRB-202-802 2-1/2”BRB-203-802 3-1/4”

rruubbbbeerr rraammmmeerr bbuuttttss

##220022 ##220033

2BA-TX00202 Steel Butt w/Bolt Hole2BA-TX00203 Socket Screw

PPaarrtt NNuummbbeerr DDeessccrriippttiioonn

25

bbeenncchh rraammmmeerrss




IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN12 10-RM2E-011 2-1/2” STEEL BUTT WITH BOLT HOLE13 10-RM2E-012 SOCKET SCREW (USE W/THREADED PISTON)14 10-RM2B-003 CYLINDER (1BA)15 10-RM2A-004 CYLINDER (2BA)16 10-RM2E-013 PACKING NUT 17 10-RM2E-014 PACKING NUT LOCK CLIP18 10-RM2E-015 VALVE BLOCK19 10-RM2E-016 VALVE BLOCK LID20 10-RM2E-017 SCREEN21 10-RM2E-018 BACKHEAD BARE22 10-RM2E-019 THROTTLE LEVER PIN23 10-RM2E-020 INLET BUSHING24 10-RM2E-021 THROTTLE VALVE O-RING - UPPER* 10-RM2E-022 THROTTLE VALVE O-RING - LOWER

IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-RM2E-001 THROTTLE VALVE SPRING PLUG2 10-RM2E-002 THROTTLE VALVE SPRING3 10-RM2E-003 LEVER4 10-RM2E-004 THROTTLE VALVE BUSHING* 10-RM2E-005 THROTTLE VALVE5 10-RM2E-006 VALVE6 10-RM2E-007 VALVE BLOCK DOWEL PIN7 10-RM2A-001 PISTON - NO THREADS (2BA)* 10-RM2B-001 PISTON (1BA)* 10-RM2A-002 PISTON WITH THREADS (2BA)8 10-RM2E-008 PACKING GLAND WASHER9 10-RM2E-009 PACKING SET10 10-RM2A-003 PACKING GLAND BUSHING (2BA)* 10-RM2B-002 PACKING GLAND BUSHING (1BA)

11 10-RM2E-010 FRONT ROD SEAL


26

ssaanndd rraammmmeerr


Blows Per Minute . . . . . . . . . . . . . . . . . 1600Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . .7/10”Length . . . . . . . . . . . . . . . . . . . . . . . . . . . 12”Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 4 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 3/8”Avg.Air Consumption (90 PSI) . . . . . . . 12 cfmTaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . .401Recommended Oil Weight . . .SAE 15 W 50

MMooddeell AATT--BBRR--0000

****SSaanndd RRaammmmeerrss aarree ssoolldd wwiitthh aa 11--33//44”” rruubbbbeerr bbuutttt****


TTooooll BBuuttttMMooddeell NNoo.. MMooddeell NNoo.. SSiizzee

AT-BR-00 BRB-201S 1-3/4”BRB-202S 2-1/2”BRB-203S 3-1/4”

##220011 ##220022 ##220033

27

ssaanndd rraammmmeerr




IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN13 10-RM2C-013 PISTON14 10-RM2C-014 GLAND WASHER15 10-RM2C-015 PACKING (20 PC)16 10-RM2C-016 O-RING17 10-RM2C-017 LOCK NUT18 10-RM2C-018 GLAND CAP19 10-RM2C-019 O-RING20 10-RM2C-020 GLAND BUSHING21 10-RM2C-021 PIN22 10-RM2C-022 THROTTLE LEVER* 10-RM2C-023 HANDLE

IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-RM2C-001 BACKHEAD2 10-RM2C-002 INLET BUSHING3 10-RM2C-003 THROTTLE VALVE4 10-RM2C-004 O-RING5 10-RM2C-005 O-RING6 10-RM2C-006 THROTTLE PLUG7 10-RM2C-007 THROTTLE SPRING8 10-RM2C-008 TOP VALVE9 10-RM2C-009 VALVE WASHER10 10-RM2C-010 MAIN VALVE11 10-RM2C-011 BOTTOM VALVE12 10-RM2C-012 BARREL

ttaammppeerr4400 llbb ccllaassss


28

880044 TTAAPPEERR

Blows Per Minute . . . . . . . . . . . . . . . . . . 800Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5”Length . . . . . . . . . . . . . . . . . . . . . . . . . 48.25”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 40 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 1/2”Avg.Air Consumption (90 PSI) . . . . . . 38.5 cfmRecommended Oil Weight . . .SAE 15 W 50

MMooddeell AATT--FFRR--66TT

****TTaammppeerrss aarree ssoolldd wwiitthh aa 66”” mmaalllleeaabbllee iirroonn bbuutttt****

29

ttaammppeerr4400 llbb ccllaassss




IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-RM1F-001 THROTTLE BODY BARE* 10-RM1F-002 THROTTLE BODY COMPLETE2 10-RM1D-001 PUSH PIN BUSHING3 10-CH1L-001 PUSH PIN4 10-CH1M-002 THROTTLE BALL SPRING5 10-RM1F-003 THROTTLE VALVE PLUG6 10-RM1F-004 THROTTLE VALVE PLUG O-RING7 10-CH1M-001 THROTTLE BALL8 10-RM1D-002 PLUNGER9 10-RM1D-003 UPPER GUIDE BUSHING10 10-RM1D-004 GUIDE BUSHING O-RING11 10-RM1D-005 PLUNGER PACKING SET12 10-RM1D-006 LOWER GUIDE BUSHING13 10-RM1D-007 PACKING NUT LOCK CLIP14 10-RM1D-008 PACKING NUT15 10-RM1D-009 CLAMP SCREW16 10-RM1D-010 6” MALLEABLE IRON BUTT* 10-RM1D-011 6” ALUMINUM BUTT

17 10-RM1D-012 EXHAUST DEFLECTOR - STEEL* 10-RM1D-013 EXHAUST DEFLECTOR - RUBBER

18 10-RM1D-014 BARREL19 10-RM1D-015 VALVE DOWEL PIN (2)20 10-RM1D-016 LOWER VALVE BLOCK O-RING21 10-RM1D-017 LOWER VALVE BLOCK22 10-RM1D-018 VALVE DISC23 10-RM1D-019 CENTER PLATE24 10-RM1D-020 UPPER VALVE BLOCK25 10-RM1D-021 OIL RESERVOIR END CAP26 10-RM1D-022 OIL CONTROL BUSHING* 10-PB1J-001 OIL PLUG

27 10-RM1D-023 CONNECTING PIPE NUT* 10-RM1D-024 BACKHEAD* 10-RM1D-025 BACKHEAD ASSEMBLY

28 10-RM1D-026 CONNECTING PIPE29 10-RM1F-005 THROTTLE LEVER FULCRUM PIN* 10-RM1D-027 THROTTLE LEVER LOCK CLIP

30 10-RM1F-006 THROTTLE LEVER


30

wweelldd fflluuxx ssccaalleerrss220000 ssttyyllee

NNEEEEDDLLEE SSCCAALLEERR

Blows Per Minute . . . . . . . . . . . . . . . . . 4600Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 1-1/8”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1”Length . . . . . . . . . . . . . . . . . . . . . . . . . . . 17”Weight . . . . . . . . . . . . . . . . . . . . . . . . 6.25 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 1/4”Minimum Hose Size . . . . . . . . . . . . . . . .5/16”Avg.Air Consumption (90 PSI) . . . . . . . 12 cfmRecommended Oil Weight . . .SAE 10 W 20

MMooddeell AATT--NNSS--220000

SSCCAALLEERR

Blows Per Minute . . . . . . . . . . . . . . . . . 4600Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 1-1/8”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1”Length . . . . . . . . . . . . . . . . . . . . . . . . . . . 15”Weight . . . . . . . . . . . . . . . . . . . . . . . . 4.75 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 1/4”Minimum Hose Size . . . . . . . . . . . . . . . .5/16”Avg.Air Consumption (90 PSI) . . . . . . . 12 cfmRecommended Oil Weight . . .SAE 10 W 20

MMooddeell AATT--SSGG--220000

****SSccaalleerr ddooeess nnoott ccoommee wwiitthh aa cchhiisseell -- aallll sstteeeell ssoolldd sseeppaarraatteellyy..****

31




IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-SC2A-001 NEEDLE SPRING2 10-SC2A-002 NEEDLE HOLDER3 10-SC2A-003 NEEDLE DRIVER4 10-SC2A-004 7” SCALER NEEDLE* 10-SC2C-004 5” SCALER NEEDLE5 10-SC2A-005 NEEDLE TUBE6 10-SC2A-006 STOPPER SPRING7 10-SC2A-007 LINER CASE8 10-SC2A-008 CUSHION SEAT9 10-SC2A-009 METAL STOPPER10 10-SC2A-010 SQUARE BUSHING11 10-SC2A-011 LINER STUD KEY12 10-SC2A-012 LINER13 10-SC2A-013 PISTON14 10-SC2A-014 BOTTOM VALVE SEAT15 10-SC2A-015 FLUTTER VALVE16 10-SC2A-016 VALVE PIN17 10-SC2A-017 TOP VALVE SEAT


IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN18 10-SC2A-018 BACKHEAD POSITIONING SPACER19 10-SC2C-001 BACKHEAD LOCK RING20 10-SC2A-019 SLOTTED HANDLE21 10-SC2A-020 THROTTLE LEVER* 10-SC2A-021 INLET BUSHING

22 10-SC2C-002 LEVER KNOCK PIN23 10-SC2C-003 THROTTLE VALVE O-RING24 10-SC2A-022 THROTTLE VALVE WITH O-RING25 10-SC2A-023 THROTTLE SPRING26 10-SC2A-024 THROTTLE PLUG GASKET27 10-SC2A-025 THROTTLE PLUG28 10-SC2A-026 BARE PUSH TYPE BACKHEAD29 10-SC2A-027 THROTTLE VALVE SNAP RING30 10-SC2A-028 THROTTLE VALVE CASING31 10-SC2A-029 SOCKET SCREW VALVE RETAINER32 10-SC2A-030 THROTTLE VALVE CASING LOCK NUT33 10-SC2A-031 CONTROL VALVE HANDLE34 10-SC2A-032 THROTTLE VALVE - PUSH TYPE


32


NNEEEEDDLLEE SSCCAALLEERR

Blows Per Minute . . . . . . . . . . . . . . . . . 4000Stroke . . . . . . . . . . . . . . . . . . . . . . . . 1-1/16”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 15/16”Length . . . . . . . . . . . . . . . . . . . . . . . . . . 10.5”Weight . . . . . . . . . . . . . . . . . . . . . . . . 8.35 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 1/4”Received Hose Size . . . . . . . . . . . . . . . . .1/4”Avg.Air Consumption (90 PSI) . . . . . . . 13 cfmRecommended Oil Weight . . .SAE 10 W 20

MMooddeell AATT--NNSS--110000

SSCCAALLEERR

Blows Per Minute . . . . . . . . . . . . . . . . . 4000Stroke . . . . . . . . . . . . . . . . . . . . . . . . 1-1/16”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 15/16”Length . . . . . . . . . . . . . . . . . . . . . . . . . . 10.5”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 1/4”Received Hose Size . . . . . . . . . . . . . . . . .1/4”Avg.Air Consumption (90 PSI) . . . . . . . 13 cfmRecommended Oil Weight . . .SAE 10 W 20

MMooddeell AATT--SSGG--110000

****SSccaalleerr ddooeess nnoott ccoommee wwiitthh aa cchhiisseell -- aallll sstteeeell ssoolldd sseeppaarraatteellyy..****

33




IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-SC2B-001 THROTTLE LEVER2 10-SC2C-001 BACKHEAD LOCK RING3 10-SC2B-002 INLET BUSHING4 10-SC2C-002 LEVER PIN5 10-SC2B-003 SLOTTED HANDLE6 10-SC2C-003 THROTTLE VALVE O-RING7 10-SC2B-004 THROTTLE VALVE8 10-SC2B-005 THROTTLE VALVE SPRING9 10-SC2B-006 THROTTLE VALVE CAP10 10-SC2B-007 VALVE CAP11 10-SC2B-008 VALVE PIN12 10-SC2B-009 VALVE SPACER13 10-SC2B-010 FLUTTER VALVE14 10-SC2B-011 VALVE SEAT15 10-SC2B-012 PISTON16 10-SC2B-013 BARREL ONLY17 10-SC2B-014 LOCK PLUNGER* 10-SC2B-015 CASE WITH LINER

18 10-SC2B-016 PLUNGER LOCK SPRING19 10-SC2B-017 RETAINER SLEEVE20 10-SC2B-018 LOCK SHIM RING21 10-SC2B-019 RETAINER STEEL BALL22 10-SC2B-020 RETAINER PIN23 10-SC2B-021 LINER ONLY24 10-SC2C-004 5” STEEL SCALER NEEDLE25 10-SC2B-022 NEEDLE DRIVER26 10-SC2B-023 NEEDLE HOLDER27 10-SC2B-024 NEEDLE SPRING28 10-SC2B-025 NEEDLE TUBE29 10-SC2B-026 INSERT FOR HOUSING


lloonngg rreeaacchh

fflloooorr ssccrraappeerr1144 llbb ccllaassss


34

..559900”” HHEEXX

Blows Per Minute . . . . . . . . . . . . . . . . . 2500Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 1.501”Bore . . . . . . . . . . . . . . . . . . . . . . . . . 1.1875”Length . . . . . . . . . . . . . . . . . . . . . . . . . . . 24”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 14 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 1/4”Avg.Air Consumption (90 PSI) . . . . . . . . 9 cfmRecommended Oil Weight . . .SAE 10 W 20

MMooddeell AATT--LLRR--LLWW5599

****FFlloooorr SSccrraappeerr ddooeess nnoott ccoommee wwiitthh aa cchhiisseell -- aallll sstteeeell ssoolldd sseeppaarraatteellyy..****

35

lloonngg rreeaacchh

fflloooorr ssccrraappeerr1144 llbb ccllaassss




IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN15 10-LR1A-016 RETAINER RING16 10-LR1A-017 RETAINER SPRING17 10-LR1A-018 FRONTHEAD BOLT WASHER18 10-LR1A-019 FRONTHEAD BOLT19 10-LR1A-020 SLEEVE O-RING19 10-LR1A-021 SLEEVE O-RING20 10-LR1A-022 PISTON21 10-LR1A-023 CYLINDER O-RING21 10-LR1A-024 CYLINDER O-RING22 10-LR1A-025 CONNECTION O-RING (2)* 10-LR1A-026 CONNECTION PIPE SHIM

23 10-LR1A-027 EXHAUST SLEEVE CAP24 10-LR1A-028 RUBBER GRIP25 10-LR1A-029 RUBBER THROTTLE GRIP26 10-LR1A-030 THROTTLE LEVER

IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-LR1A-001 SPLIT PIN2 10-LR1A-002 THROTTLE BODY* 10-LR1A-003 THROTTLE BODY COMPLETE3 10-LR1A-004 THROTTLE VALVE O-RING4 10-LR1A-005 THROTTLE VALVE5 10-LR1A-006 THROTTLE PLUG O-RING6 10-LR1A-007 THROTTLE PLUG7 10-LR1A-008 THROTTLE VALVE SPRING8 10-LR1A-009 CONNECTING PIPE9 10-LR1A-010 EXHAUST SLEEVE10 10-LR1A-011 CYLINDER11 10-LR1A-012 CYLINDER SLEEVE12 10-LR1A-013 FRONTHEAD13 10-LR1A-014 RETAINING BALL (2)14 10-LR1A-015 RETAINER

hheeaavvyy dduuttyy ssccrraappeerr


36

..558800”” HHEEXX

Blows Per Minute . . . . . . . . . . . . . . . . . 3850Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5”Length . . . . . . . . . . . . . . . . . . . . . . . . . . . 53”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 17 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 1/2”Avg.Air Consumption (90 PSI) . . . . . . . 12 cfmRecommended Oil Weight . . .SAE 10 W 20

MMooddeell AATT--LLRR--HHDD5588

..668800”” RROOUUNNDD

Blows Per Minute . . . . . . . . . . . . . . . . . 3850Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5”Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5”Length . . . . . . . . . . . . . . . . . . . . . . . . . . . 53”Weight . . . . . . . . . . . . . . . . . . . . . . . . . 17 lbsAir Inlet Thread . . . . . . . . . . . . . . . . . . . 1/2”Avg.Air Consumption (90 PSI) . . . . . . . 12 cfmRecommended Oil Weight . . .SAE 10 W 20

MMooddeell AATT--LLRR--HHDD6688

****FFlloooorr SSccrraappeerr ddooeess nnoott ccoommee wwiitthh aa cchhiisseell -- aallll sstteeeell ssoolldd sseeppaarraatteellyy..****

37

hheeaavvyy dduuttyy ssccrraappeerr




IINNDDEEXX PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN1 10-RM1F-006 THROTTLE LEVER2 10-RM1F-005 THROTTLE LEVER FULCRUM PIN3 10-LR1B-001 RUBBER GRIP4 10-RM1F-001 THROTTLE BODY BARE* 10-RM1F-002 THROTTLE BODY COMPLETE5 10-LR1B-002 PUSH PIN6 10-CH1M-001 THROTTLE BALL7 10-LR1B-003 PUSH PIN O-RING8 10-CH1M-002 THROTTLE BALL SPRING9 10-RM1F-004 THROTTLE VALVE PLUG O-RING10 10-RM1F-003 THROTTLE VALVE PLUG11 10-LR1B-004 CONNECTING PIPE 36” 12 10-LR1B-005 SOLID BACKHEAD13 10-CH1O-001 CYLINDER O-RING14 10-LR1B-006 UPPER VALVE PLATE15 10-LR1B-007 VALVE SPRING (3)16 10-LR1B-008 BUMPER VALVE PLATE17 10-LR1B-009 PISTON18 10-LR1B-010 LOWER VALVE RING19 10-LR1B-011 CYLINDER (W/REPLACEABLE .580 HEX BUSHING)20 10-LR1B-012 CHISEL BUSHING .580” HEX* 10-LR1B-013 CHISEL BUSHING .680” ROUND

21 10-LR1B-014 RETAINER SPRING

TTooooll BBuuttttMMooddeell NNoo.. PPaarrtt NNoo.. SSiizzeeAT-BR-00 BRB-201S 1-3/4”

BRB-202S 2-1/2”BRB-203S 3-1/4”

AT-BR-2BA BRB-202-802 2-1/2”BRB-203-802 3-1/4”

AT-BR-1BA BRB-202-802 2-1/2”BRB-203-802 3-1/4”

aacccceessssoorriieess


38

PPaarrtt NNoo.. DDeessccrriippttiioonnCHR-1190CP Solid/Taper/Oval (Chicago Pneumatic Style)CHR-1190IR Solid/Taper/Oval (Ingersoll Rand Style)CHR-1190SUL* Solid/Taper/Oval (Sullair Style)CHR-11901655 Solid/Straight/Oval (K2L Style)CHR-1190APT Solid/Straight/Oval (APT Style)

CHR-1291CP Quick Change/Taper (Chicago Pneumatic Style)CHR-1291IR Quick Change/Taper (Ingersoll Rand Style)CHR-1291SUL* Quick Change/Taper (Sullair Style)CHR-1291APT Quick Change/Straight (APT Style)

CHR-SPRING Lock Spring - Fits all styles

QQuuiicckk CChhaannggee RReettaaiinneerrSSoolliidd RReettaaiinneerr LLoocckk SSpprriinngg

*Fits Champion Chisel Works hammers.

PPaarrtt NNoo.. DDeessccrriippttiioonnHS-782412 7/8”-24 UNC x 1/2” Hose Barb HS-3812 3/8” NPT x 1/2” Hose Barb HS-1212 1/2” NPT x 1/2” Hose BarbWHA-6CH 6’ whip hose assembly with HS-782412

swivel, coupling and ILO-S in line oiler.

AAiirr IInnlleett HHoossee SSwwiivveell

PPaarrtt NNoo.. IILLOO--SS IILLOO--MM IILLOO--LLOil Capacity 1.4 oz 3.7 oz 11 ozPipe Size 1/2” 3/4” 3/4”Max.Working Pressure 500 psi 260 psi 300 psiDimensions 4-1/2”x2-1/4” 6” x 2-3/4” 7”x3-1/2”Weight .875 lbs 1.5 lbs 2 lbs

WWhhiipp HHoossee AAsssseemmbbllyy IInn LLiinnee OOiilleerr

PPaarrtt NNoo.. FFiittss TTooooll II..DD..RBR-21902557 CP-4181 2.557”RBR-21902565 JET RB11 2.565”RBR-21902400 JET RB90, RB91 2.400”RBR-21902445 CP-60, 80, 90 2.445”RBR-1851 APT133/MP1133 2.610”RBR-9001200 IR9001 ThreadedRBC-9RB-207 Clip for RBR-9001200

PPaarrtt NNoo.. DDeessccrriippttiioonnRBP-RB2104 Rubber BumperRBP-UB2102 Urethane BumperRBP-US2101 Upper SleeveRBP-LS2103 Lower SleeveRBP-LS2103S Split Lower SleeveRBP-RS2194 Retainer Spring10-RB1N-001 3” Piston / 6” & 8” Stroke10-RB1M-002 4” Piston / 11” Stroke

RRuubbbbeerr BBuummppeerr

LLoocckk SSpprriinngg

UUppppeerr SSlleeeevvee SSpplliitt LLoowweerr SSlleeeevveeLLoowweerr SSlleeeevvee

RReettaaiinneerr

cchhiippppiinngg hhaammmmeerr rriivveett bbuusstteerr

sswwiivveellss && ooiilleerrss


##220011 ##220022

##2200332BA-TX00202 Steel Butt w/Bolt Hole2BA-TX00203 Socket Crew

PPaarrtt NNuummbbeerr DDeessccrriippttiioonn

39


sstteeeell bbiittss

Champion Chisel Works offers a full range of steel bits for air tools. Consult your ChampionChisel Works steel product catalog or call 815-535-0647 to request more information.

..558800”” HHeexx SShhaannkk -- RRoouunndd,, OOvvaall && NNoonn CCoollllaarr

..668800”” RRoouunndd SShhaannkk -- RRoouunndd,, OOvvaall && NNoonn CCoollllaarrMoil Point Narrow1.5” Wide 2” Wide2.5” Wide 3” WideBush Tool Clay Spade

Floor Scraper System

77//88”” xx 33--11//44”” SShhaannkk 11”” xx 44--11//44”” SShhaannkk11--11//88”” xx 66”” SShhaannkk 11--11//44”” xx 66”” SShhaannkk

Moil Point Narrow3” Wide Asphalt CutterBush Tool Clay Spade

ppnneeuummaattiicc cchhiippppiinngg hhaammmmeerrss ppnneeuummaattiicc ppaavveemmeenntt bbrreeaakkeerrss

Moil Point NarrowRipper

jjuummbboo rriivveett bbuusstteerrss

33//44”” HHeexx DDeemmoo SSpplliinnee DDrriivvee SSttyylleeSSDDSS MMaaxx SSttyyllee KKaannggoo 2211mmmm SSttyylleeSSDDSS PPlluuss SSttyyllee MMaakkiittaa 88990000NN SSttyylleeWWaacckkeerr SSttyyllee 11--11//88”” HHeexx NNoottcchh

HHiillttii 880055//990055 SSttyyllee MMaakkiittaa HHKK11881100 SSttyylleeMoil Point Narrow2” Wide 3” WideBush Tool Clay Spade

Asphalt Cutter Bent ChiselFloor Scraper System

eelleeccttrriicc cchhiippppiinngg hhaammmmeerrss

..440011 TTuurrnn TTyyppee ..440011 NNoonn--TTuurrnn TTyyppee

..449988 TTuurrnn TTyyppee ..449988 NNoonn--TTuurrnn TTyyppeeMoil Point BlankNarrow Taper Punch

2” Wide Chisel Bent Chisel

ppnneeuummaattiicc zziipp gguunnss

CClleeccoo SSttyyllee IInnggeerrssoollll RRaanndd SSttyyllee..337711 SSttyyllee ..443322 SSttyylleeMoil Point BlankNarrow Wide Chisel

Bent Chisel

wweelldd fflluuxx ssccaalliinngg hhaammmmeerrss

HH TThhrreeaadd 1111 DDeeggrreeee TTaappeerreeddDD TThhrreeaadd EE TThhrreeaadd

RRooppee7/8” x 3-1/4” Shank 7/8” x 4-1/4” Shank

1” x 4-1/4” Shank

ddrriillll sstteeeell && rroocckk bbiittss

77//88”” xx 33--11//44”” SShhaannkk 77//88”” xx 44--11//44”” SShhaannkk11”” xx 44--11//44”” SShhaannkk CC--99 CCllaassss

wwhhiirrlleeyy bbiittss

AA ccoommpplleettee lliinnee ooff bbiittss aarree aavvaaiillaabbllee --pplleeaassee ccaallll ffaaccttoorryy wwiitthh tthhee MMaannuuffaaccttuurreerr &&MMooddeell NNuummbbeerr ooff yyoouurr hhyyddrraauulliicc bbrreeaakkeerrffoorr pprriicciinngg && aavvaaiillaabbiilliittyy..

bboooomm mmoouunntteedd ddeemmoo bbiittss

2.008”

.374

”

.500”

.827” .906”

.500”

1.102”1.614”

1.25

”

1.81

1”

1.25”

6.00” .472”

1.12

5”

1.81

1”

1.125”

6.00” .472”

1.00

”

1.57

5”

1.00”

.472”4.25”

.875

”

1.57

5”

.875”

3.25” .472”

.630

”

.276”

.432”

1.772”

.787

”

1.26”

.500

”

.748

”

.371

”

.252”

1.181”

1.378”

.512

”

.630

”

.498

”

2.126”

1.047”

.630

”

.925”

.401

”

1.614”

.630

”

.846

”

.498

”

.197”1.575”

.492

”

.748

”

.401

”

.138”1.575”

.812

”

.680

”

2.375”

.812

”

.680

”

.580”

1.752”

2.375”

.812

”

.680

”

2.375” .453”.453”2.375”1.732”

.580”

.812

”

.680

”

.812

”

1.26

”

.680

”2.375” .453”.453”2.375”

1.732”

.580”

.812

”

1.26

”

.680

”SShhaannkk RReeffeerreennccee

..440011 TTuurrnn TTyyppee ..449988 TTuurrnn TTyyppee

pneumatic chipper steel

pneumatic zip gun bits weld flux scaling bits

pavement breaker steel

electric chipper steel

rivet buster

..440011 NNoonn--TTuurrnn TTyyppee ..449988 NNoonn--TTuurrnn TTyyppee

..668800 RRoouunndd // RRoouunndd CCoollllaarr..558800 HHeexx // RRoouunndd CCoollllaarr

..668800 RRoouunndd // OOvvaall CCoollllaarr..558800 HHeexx // OOvvaall CCoollllaarr

..558800 HHeexx // NNoonn--CCoollllaarr ..668800 RRoouunndd // NNoonn--CCoollllaarr

IInnggeerrssoollll RRaanndd SSttyyllee CClleeccoo SSttyyllee

..337711 SSttyyllee ..443322 SSttyyllee

77//88”” xx 33--11//44”” SShhaannkk 11”” xx 44--11//44”” SShhaannkk

11--11//88”” xx 66”” SShhaannkk 11--11//44”” xx 66”” SShhaannkk JJuummbboo RRiivveett BBuusstteerr

SSpplliinnee DDrriivvee SSttyyllee33//44”” HHeexx DDeemmoo

SSDDSS MMaaxx SSttyyllee KKaannggoo 2211MMMM SSttyyllee

SSDDSS PPlluuss SSttyyllee MMaakkiittaa 88990000NN SSttyyllee

WWaacckkeerr 33//44”” xx 33--11//44”” SSttyyllee 11--11//88”” HHeexx//NNoottcchh

.890

”

1.12

5”

1.875”

1.378”

.650

”

.748” .748”

2.52” 3.031”

.709

”

4.016”

2.559”.827”

.748

”

.394

”

.551

”

1.181”

4.291”

2.165”

.945

”

3.25”

1.26

”.748”

.315”

6.00”.472”

1.125”

5.197”

1.81

1”

AAddddiittiioonnaall eelleeccttrriicc sshhaannkkss::HHiillttii 880055//990055 SSttyylleeMMaakkiittaa HHKK11881100 SSttyylleeEEddccoo ..558800”” HHeexx SSttyylleeEEddccoo 77//88”” HHeexx SSttyyllee

40


safety tips & warnings - Champion Chisel

Documents

Transcript of safety tips & warnings - Champion Chisel