This symbol indicates the presence of dangerous voltage inside the enclosure, sufficient enough to cause electric shock. This symbol indicates the presence of important operating and maintenance instructions for the device.

Safety, Environmental and Setup Instructions

• Use the device in dry indoor environments only. • Protect the device from humidity. • Do not open the device. RISK OF ELECTRIC SHOCK! Refer opening and servicing to qualified personnel. • Connect this device to a properly installed and earthed wall outlet only. Make sure the mains voltage corresponds with

the specifications on the rating plate. • Make sure the mains cable stays dry during operation. Do not pinch or damage the mains cable in any way. • A damaged mains cable or plug must immediately be replaced by an authorized service center. • In case of lightning, immediately disconnect the device from the mains supply. • Children should be supervised by parents when using the device. • Clean the device with a dry cloth only.

Do NOT use CLEANING AGENTS or ABRASIVE CLOTHS! • Do not expose the device to direct sunlight or other heat sources. • Install the device at a location with sufficient ventilation in order to prevent heat accumulation. • Do not cover the ventilation openings! • Install the device at a safe and vibration-free location. • Install the device as far away as possible from computers and microwave units; otherwise radio reception may be

disturbed. • Do not open or repair the enclosure. It is not safe to do so and will void your warranty. Repairs only by authorized

service/ customer center. • Only use mercury and cadmium-free batteries. • Used batteries are hazardous waste and NOT to be disposed of with the household waste!!!

Return the batteries to your dealer or to collection points in your community. • Keep batteries away from children. Children might swallow batteries.

Contact a physician immediately if a battery was swallowed. • Check your batteries regularly to avoid battery leakage. • Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. • CAUTION: Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type

ENVIRONMENTAL PROTECTION

Do not dispose of this product with the normal household waste at the end of its life cycle. Return it to a collection point for the recycling of electrical and electronic devices. This is indicated by the symbol on the product, user manual or packaging.

The materials are reusable according to their markings. By reusing, recycling or other forms of utilization of old devices you make an important contribution to the protection of our environment.

Please contact your local authorities for details about collection points.

WARNING

Risk of electric shock Do not open!

Caution: To reduce the risk of electric shock, do not remove the

cover (or back). There are no user serviceable parts inside. Refer

servicing to qualified service personnel.

UR180 / English Instruction Manual

1

LOCATION OF CONTROL 1. SNOOZE/SELECT/SCAN

2. LCD DISPLAY

3. REMOTE SENSOR

4. ANTENNA

5. AUX IN

6. STANDBY/FUNC.

7. MENU/INFO 8. TUNE+

9. TUNE-

10. VOL+/AL1

11. VOL-/AL2

12. AC POWER CORD

UR180 / English Instruction Manual

2

LOCATION OF CONTROL 1) STANDBY

2) FUNCTION

3) MUTE

4) SELECT

5) TUNE-

6) ALARM 1

7) ALARM 2

8) PRESET

9) PRESET-

10) SCAN

11) SLEEP

12) SNOOZE

13) VOLUME-

14) MENU

15) TUNE+

16) INFO

17) PRESET+

18) EQ

19) VOLUME+

UR180 / English Instruction Manual

3

BASIC FUNCTION 1. Press the “STANDBY” button to switch on the unit.

2. Press the “FUNC.” button to select “DAB/FM/AUX” mode.

3. Press the “VOL-” or “VOL+” button to adjust volume level.

4. Press and hold the “STANDBY” button 2 seconds to switch off the unit in all modes.

FM RADIO OPERATION

AUTOMATIC TUNING

1. Press the “FUNC.” button to select FM mode.

2. Press and hold the “TUNE-” or “TUNE+” button 2 seconds or press the “SCAN” button to start automatic tuning process.

3. When a station is tuned in the tuning process, it will stop automatically and you can listen to your desired station.

MANUAL TUNING

It is for selecting stations, which cannot be tuned automatically. (manual selection)

To tune a channel manually:

1. Press the “FUNC.” button to select FM mode.

2. Press the “TUNE-” or “TUNE+” button to select station.

3. Each time the “TUNE-” or “TUNE+” button is pressed momentarily (0.5 second or less), the frequency changes by a fixed step: 0.05MHz.

MEMORY PRESET

Up to 10 stations can be preseted

1. Press the “PRESET” button on the remote controller to start the preset process.

2. Display will show “Preset 1 empty”.

3. Press the “TUNE-” or “TUNE+” button to determine the preset station number.

4. Press and hold the “SELECT” button 2 seconds to preset your desired station.

5. Once all the stations were preset, press the “PRE-” or “PRE+” button to select your preset station.

6. Press the “SELECT” button to confirm and listen to your desired station.

AUTO SCAN

This product equipped auto station scan & saving function. Up to 30 stations can be saved.

• Press the “FUNC.” button to select FM mode.

• Press and hold the “SCAN” button 2 seconds, unit will auto search and save all available radio station.

• Press and hold the “PRESET” button on the remote controller 2 seconds to select the previous present station list.

• Press the “TUNE-” or “TUNE+” button to select your preset station.

• Press the “SELECT” button to confirm to listen to your desired station.

FM INFO

In FM mode, press the “INFO” button to show FM information. Each press the LCD will show below information:

• Radio text.

UR180 / English Instruction Manual

4

• Information (Program type).

• Signal strength.

• Time/Date.

FM RADIO OPERATION

FM MENU

In FM mode, press and hold the “MENU” button to enter FM menu, press the “TUNE-” or “TUNE+” button to select

FM menu as follows:

• Audio setting

• Main menu

---Audio setting • In FM menu, press the “TUNE-” or “TUNE+” button to select “Audio setting”.

• Press the “SELET” button on the remote controller to confirm.

• Press the “TUNE-” or “TUNE+” button to select “Stereo or mono” or “Mono only”.

• Press the “SELECT” button to confirm.

---Main menu • In FM menu, press the “TUNE-” or “TUNE+” button to select “Main menu”.

• Press the “SELECT” button to confirm.

• Press the “TUNE-” or “TUNE+” button to select main menu features as follows.

1) Time setup

2) Factory reset

3) SW version

• Press the “SELECT” button to confirm.

1) Time setup

• In FM menu, press the “TUNE-” or “TUNE+” button to select “Time setup”.

• Press the “SELECT” button to select “Time setup” features as follows.

a) Set clock

b) Set date

c) Auto update

d) Set 12/24 hour

• Press the “SELECT” button to confirm.

a) Set clock

1) Press the “SELECT” button to select “Set clock”.

2) Display will show “00:00 AM” if 12H format is set or “00:00” if 24H is set.

3) Adjust hour by pressing the “TUNE-” or “TUNE+” button, press the “SELECT” button to confirm.

4) Adjust minute by pressing the “TUNE-” or “TUNE+” button, press the “SELECT” button to confirm.

5) Press the “TUNE-” or “TUNE+” button to select “AM” or “PM”, press the “SELECT” button to confirm.

b) Set date

1) Press the “SELECT” button to select “Set date”.

2) Adjust date by pressing the “TUNE-” or “TUNE+” button, press the “SELECT” button to confirm.

3) Adjust month by pressing the “TUNE-” or “TUNE+” button, press the “SELECT” button to confirm.

4) Adjust year by pressing the “TUNE-” or “TUNE+” button, press the “SELECT” button to confirm.

c) Auto update

1) Press the “SELECT” button to select “Auto update”.

UR180 / English Instruction Manual

5

2) Press the “TUNE-” or “TUNE+” button to select “From radio” or “No update”.

3) Press the “SELECT” button to confirm.

d) Set 12/24 hour

1) Press the “SELECT” button to select “Set 12/24 hour”.

2) Press the “TUNE-” or “TUNE+” button to select “12 hour” or “24 hour”.

3) Press the “SELECT” button to confirm.

2) Factory reset

a) In FM menu, press the “TUNE-” or “TUNE+” button to select “Factory reset”.

b) Press “SELECT” to confirm.

c) Display will show “press enter to confirm reset”.

• Press the “SELECT” button to confirm. Display will show “Restarting, Do not power off”.

• All setting will be cancelled and restore to factories setting.

3) SW version

• In FM menu, press the “TUNE-” or “TUNE+” button to select “SW version”.

• Press the “SELECT” button to confirm. Software version information will show on display.

DAB OPERATION

AUTOMATIC TUNING 1. Press the “FUNC.” button to select DAB mode.

2. The unit will start automatic tuning process and saving (not save in memory preset). Up to 100 stations can be saved.

3. Press the “TUNE-” or “TUNE+” button to select your desired station and press the “SELECT” button to confirm. You can listen to your desired DAB station.

MANUAL TUNE

It is for selecting stations, which cannot be tuned automatically. (manual selection)

To tune a channel manually:

1. Press the “FUNC.” button to select DAB mode.

2. Press the “MANU” button to enter DAB menu.

3. Press the “TUNE-” or “TUNE+” button to select “Station scan”. And then press “SELECT” to confirm.

4. Press the “TUNE-” or “TUNE+” button to select “Manual tune”. Press the “SELECT” button to confirm.

5. Press the “TUNE-” or “TUNE+” button to select DAB frequency range. For example: 5A 174.928MHz.

6. Press the “SELECT” button to confirm and the unit will start scan and save all available station.

7. Press the “TUNE-” or “TUNE+” button to select your desired station and listen.

MEMORY PRESET

Up to 10 stations can be preseted

1. Press the “PRESET” button on the remote controller to start the preset process.

2. Display will show “Preset 1 empty”.

3. Press the “TUNE-” or “TUNE+” button to determine the preset station number.

4. Press and hold the “SELECT” button 2 seconds to preset your desired station.

5. Once all the stations were preset, press the “PRE-” or “PRE+” button to select your preset station.

UR180 / English Instruction Manual

6

6. Press the “SELECT” button to confirm and listen to your desired station.

DAB OPERATION

AUTO SCAN

This product equipped auto station scan & saving function. Up to 100 stations can be saved.

1. Press the “FUNC.” button to select DAB mode.

2. Press “MENU” button to enter DAB menu.

3. Press the “TUNE-” or “TUNE+” button to select “Station scan”. And then press “SELECT” to confirm.

4. Press the “TUNE-” or “TUNE+” button to select “Full scan”. Press the “SELECT” button to confirm.

5. The unit will start auto scan and save all available station.

6. Press the “TUNE-” or “TUNE+” button to select your desired station and listen.

DAB INFO

In DAB mode, press the “INFO” button to show DAB information. Each press the LCD will show below information:

• DLS (Scrolling text).

• PTY (Programme Type).

• Group Name(DAB station name)

• Time/Date

• DAB Frequency

• Transfer Rate

• Signal strength.

• Signal error rate.

MAIN MENU • In DAB menu, press the “TUNE-” or “TUNE+” button to select “Main menu” and then press the “SELECT” button to

confirm. Press the “TUNE-” or “TUNE+” button to select main menu features as follows:

1) Time setup

2) Factory reset

3) SW version

• Press the “SELECT” button to confirm.

• Please refer to FM “MAIN MENU”.

AUX IN OPERATION • Connect 3.5mm jack cable to this unit and your device.

• Press the “FUNC.” button to select “AUX” mode.

• Press “Play” on your device and enjoy.

• Press the “VOL-” or “VOL+” to adjust the volume level.

OTHER FEATURES

ALARM SETTING • ALARM setting must be at standby mode and after completed clock setting.

UR180 / English Instruction Manual

7

• Press the “AL1” or “AL2” button to entry alarm set mode.

• Display will show “ALARM1 OFF” or “ALARM2 OFF”. Press the “SELECT” button to confirm.

• Display will show “Off”, press the “SELECT” button to select “On”.

• Press “TUNE+” button to entry alarm time setting. Press the “SELECT” button to confirm.

• Adjust hour by pressing “TUNE-” or “TUNE+” button. Press the “SELECT” button to confirm.

• Adjust minute by pressing “TUNE-” or “TUNE+” button. Press the “SELECT” button to confirm.

• Press the “TUNE+” button to entry alarm days setting. Press the “SELECT” button to confirm.

• Press the “TUNE+” button to select “Daily” or “Once” or “Weekdays” or “Weekends”. Press the “SELECT” button to confirm.

• Press the “TUNE+” button to entry alarm source setting. Press the “SELECT” button to confirm.

• Press the “TUNE+” button to select “DAB” or “FM” or “Buzzer”. Press the “SELECT” button to confirm.

• Press the “TUNE+” button to entry alarm volume setting. Press the “SELECT” button to confirm.

• Press the “TUNE-” or “TUNE+” button to adjust volume level. Press the “SELECT” button to confirm.

• Press the “TUNE+” button to entry alarm save setting. Press the “SELECT” button to confirm to save.

• Display will show alarm setting information when alarm setting finished.

• Notes: If you need to reset the alarm, press the “AL1” or “AL2” button and then press the “SELECT” button to reset the alarm setting.

SNOOZE • When the alarm is triggered, you may press the “SNOOZE” button to delay the alarm. This appliance allows you to

press the “SNOOZE” button to delay the alarm 4 times. The first time you press the “SNOOZE” button to delay the alarm for another 5 minutes. The second time is to delay 10 minutes, the third time is to delay 15 minutes and the fourth time is to delay 30 minutes.

SLEEP • Sleep type: Sleep off, 15, 30, 45, 60, 90

• Press the “SLEEP” button on remote controller then display show “Sleep off”.

• Press the “SLEEP” button again then display show “Sleep 15”.

• Repeat the procedure to choose the correct setting.

EQ • EQ type: Flat-Rock-Classic-Jazz-Pop

• Press the “EQ” button on remote controller to choose the correct setting.

MUTE • Press the “MUTE” button on remote controller to switch volume on/off.

SPECIFICATION FM: 87.5-108MHz

DAB+: Band III, 174.928-239.200MHz

POWER SOURCE: 100-240V~60/50Hz

SPEAKER IMPEDANCE: 4 ohm

POWER CONSUMPTION: 12W

Technische Änderungen und Druckfehler vorbehalten Copyright by Woerlein GmbH, 90556 Cadolzburg, www.woerlein.com Vervielfältigung nur mit ausdrücklicher Genehmigung der Woerlein GmbH