Saddle Patterns
-
Upload
confused597 -
Category
Documents
-
view
215 -
download
0
Transcript of Saddle Patterns
-
8/9/2019 Saddle Patterns
1/4
Alternate Saddle Kit PatternsAlternate Saddle Patterns to Fit Etched Corner Plates & Saddle Accessories BR11
Version 1.01/27/2006
With the introduction of our new Etched Plates, you likely will need to make some modifica-tions to your patterns for an accurate fit and be able to get the full benefit from all of the plates.This may also be applicable when using our standard Pewter plates.
These modified patterns are provided as a helpful service for the exclusive use of our customers.
Please do not redistribute them, but instead refer folks to our website at www.riorondo.com.
Over time, western saddle styling changes according to various fads andtrends. While our basic Western Saddle Kit (Part #KWT1) is a middle-of-the-road option, you may wish to make some changes to suit your fan-cies (or current trends). Learning to do so will provide you many newoptions for saddles you create.
Current show saddles tend to have very deep skirts, when viewed fromtop to bottom, (leaving a lot more area to show off fancy silver and plates!)There also may be quite a bit of distance between where the bottom ofthe Upper Skirt rests in relation to the Lower Skirt. Other areas of the sad-dle such as Seat pieces and Fenders may also be cut differently, to accom-
modate even more decoration. In addition, there are many variations tobe found in how saddles are rigged up (rigging plates, low-set dees, vestigial rear cinch billets and more) that you may wish to replicate in miniature. Weve included a number of optional patterns here to help you gethe most from your plates and enjoy more stylistic options in general.
To Use these Patterns, simply substitute in the new pattern pieces for existing saddle kit pattern pieces. If you are working with the supplies from ouWestern Saddle Kit, please be aware that to make larger skirts, you wirequire extra Tooling Leather (Part #LT2), and Chamois (Part #LCH2to account for the increased size.
You can use either the standard cinch slots provided on the lower skirtpatterns, or add dee ring riggings (or a combination). Shown are fourcommon variations.
Three front rigging strap patterns are included. You only need one persaddle. The curved ones allow you to place the rigging strap behind theshoulders, rather than under them.
During assembly, Rigging straps (if used) should be located on top of theLower Skirt, and under the saddle tree.
If you are using a front Dropped Rigging, you may need to adjust thelength of your front cinch (it may need to be a bit shorter.)
Shaded areas on the ends of the rigging straps indicate where the endsshould be skived and folded over for tabs to glue down. Use thin, butstrong leather for the rigging straps (skive if necessary) for less bulk underthe tree.
If using Rear Dee Riggings, DO NOTcut rigging slots in rear skirts.
Slots with a GREY outline are for inset plates. Slot with a BLACK outlineare for plates to be set flush with the skirts edge.
Two slot positions are provided for the front breastcollar rigging dee. Useither the vertical or the slanted one (not both!) You can place your owslots in this area if you prefer the dees be located differently.
Special Notes:Weve provided an optional curved cantle pattern as an alternative tothe straight one included in our Saddle Kit.
Alternative Stirrup patterns are included that will correspond to variouStirrup Panel plates.
Flip over alternate Seat Piece and Fender pattern pieces to create thopposite matching sides for these items.
Upper and lower skirt patterns can be created in halves (left and rightif needed. The dotted line indicates the centerline of the pattern.
Corner Plate #P151 (Concho style) is a little longer than other corneplates, so if you are using a rear cinch slot you will need to adjust its position so the plate will not cover it.
BEFORE YOU START...Advance planning needs to go into a saddle that you plan to outfit with decorative plates before you trace and cut the leather.
Have the decorated plates on hand that you wish to use.
Check the plates against the three different pattern alternates, to find which one best fits the corner plates you will be using.
The following Options will need to be determined in advance. These options include:Choice of Basic Skirt Style (both Lower and Upper Skirts)
Choice of matching Fender and Seat Piece Styles
Rigging Style
Breastcollar Rigging Dee location
Choice of Stirrup Style to match the Stirrup Panel Plates you will be using.
Common Rigging Options:
StandardSlot Rigging
Front Dee Riggingand Rear Slot
Front and RearDee Riggings
Dropped Front andStandard Rear Dee Riggings
Traditional (1:9) Scale
-
8/9/2019 Saddle Patterns
2/4
A A
B
E
C
F
F
F
G
B orC(optional)
B orC(optional)
PA-A
PA-BPA-C
PA-D
PA-FPA-G
PA-HPA-J
PA-KRear CinchBuckle
PA-E
BCF
Corner Plate Sheet Saddle Accessories Sheet
Corner Plate Sheet Key
A2 Large Corner Plates
B4 Medium Corner Plates
C4 Small Corner Plates
D1 Cantle Plate
E1 Horn CapF6 Saddle Conchos
Saddle Accessories Key
A 1 Gullet Plate
B 2 Front Rigging Dees
C 2 Rear Rigging Dees
D 2 Breastcollar Rigging Dees
E 2 Stirrup PanelsF 2 Slot Covers
G 2 Rear Billet Tips
H 1 Latigo Keeper
J 1 Buckle Keeper
K 2 Rear Cinch Buckles
Special Notes on Tooling:
Trace the pattern outline of the parts you will be tooling ontotooling film with pencil. One by one, place each plate ontothe tooling film in its appropriate location and trace its out-line onto the film with pencil.
Now you can work your tooling pattern around the plates.While you can go ahead and attach the plates directly overtooled areas, you may wish to customize the pattern to makethe plates more a part of the design. Additionally, why go toall the trouble of tooling areas that will be covered up?
Once you have completed your tooling pattern on the film,put the film pencil-side-up on top of the leather piece
(leather should be lightly and evenly dampened).
Using a small ball stylus or leather tracing tool apply light pres-sure to impress the outline of your design on the leather.
Please be aware that the leather can easily warp and stretchwhile youre working it, causing the plates to not quite fitwhen its ready to assemble. Check the plates against yourtooling work frequently, so you can push and pull the leatheraround a bit to keep things lined up as you go.
To Use the Pattern Pieces:
Print out the two pattern pages (Pages 3 and 4 of this document) ontopaper. Heavy paper or card stock is best. Then cut out the pieces andtrace around them on theback(flesh) side of the leather and care-fully cut the leather pieces out.
Alternatively, you may simply print out the pages, and use tooling filmto trace the lines of the patterns, then transfer the pattern to theleather as you would as in our Western Saddle Kit, and cut the piecesout.
PA=Saddle Accessories Sheet
2006 Rio Rondo Enterprises
All Rights Reserved
These patterns are provided for the exclusive use of our customers,
and may not be redistributed in any manner without prior written consent.
-
8/9/2019 Saddle Patterns
3/4
Alternate Saddle Pattern I
Fits:P140P141P142P143P144P145P149P152
May be used forP170-175
Upper Skirt I-BUpper Skirt I-A
Lower Skirt I-A Lower Skirt I-B FenderI-B
FenderI-A
Seat Piece I-A
Seat Piece I-B
Seat Piece I-DSeat Piece I-C
Fron
t RiggingStrap-B
Fron
tDropped RiggingStrap
-B
Front Dropped Rigging Strap-A
Front Rigging Strap-A
Rear Rigging Strap
Stirrup A
Stirrup B
Stirrup C
Stirrup D
Stirrup E
Cantle
Additional Alternate Pattern Pieces
Alternate Stirrup Patterns to fitVarious Stirrup Panel Shapes
Optional Rigging Straps to use Rigging Dees on a SaddRigging Straps marked as "B" are curved so that thstrap will go over the skirt behind the shoulderather than be under the shoulders.
If you use Rigging straps, you will not need to cutslots in the skirt at the corresponding locations.
Check plates on the pattern pieces for corner fit to select the style that best matches.
2006 Rio Rondo EnterprisesAll Rights Reserved
These patterns are provided for theexclusive use of our customers, andmay not be redistr ibuted in anymanner w i thou t p r i o r wr i t tenconsent.
-
8/9/2019 Saddle Patterns
4/4
Fits:P146P147P148P150P151P153P154
May be used forP170-175
Fits:P148P149P152
May be used forP170-175
Lower Skirt II-A Lower Skirt II-B
Seat Piece II-ASeat Piece II-B
FenderII
UpperSkirtIII-A
UpperSkirtIII-B
Fender
III
Seat Piece III
UpperSkirtII
Lower Skirt III-BLower Skirt III-A
Check plates on the pattern pieces for corner fit to select the style that best matches.
Alternate Saddle Pattern II
Alternate Saddle Pattern III
2006 Rio Rondo EnterprisesAll Rights Reserved
These patterns are provided for the exclusive useof our customers, and may not be redistributedin any manner without prior written consent.