Cartridge Refill Instructions Our universal ink can be used to refill all Inkjet Cartridge Models listed below. This kit contains: 1 bottle of Black ink or 1 x bottle each of Cyan, Magenta and Yellow ink 3 steel balls, 1 ball pushing tool 5 adhesive tapes, 5 round labels, 1 drill, 1 air pump To ensure best printing results, please read these instructions carefully and follow them step by step when refilling your cartridge : 1. Make sure the print head is in normal condition and not clogged with dried ink. 2. Make sure you refill your cartridge immediately when it is almost empty 3. The cartridge should be put back into the printer right after refilling ; otherwise the print head may

get clogged. 4. Do not refill the cartridge with more than the appropriate amount of ink. 5. Sip up the ink at the nozzles instead of wiping with tissue paper. 6. Do not mix colors when refilling. Note : rinse the syringe and needle with water every time

you use it in order to avoid color mixture. 7. Protect the circuit board on the cartridge from ink or water. 8. Use your printer menu to install the refilled cartridge back into your printer, then the printer will run

a print head cleaning cycle automatically. 9. Only start printing after the cleaning cycle is finished. 10. If white lines appear on the printout or no ink is coming out, you need to clean the print head 2-3

times again by following your printer menu. If the printing quality is still not satisfactory, then leave the cartridge idle in the printer for a while before you start printing again.

REFILL CATEGORY 1 EPSON : SO20108, SO20138, SO20187, SO20189, SO20191, T003, T005, T007~T009, T013~T015, T017~T020, T026, T028, T031, T036, T038, T040, T041, T050~T053, T057, T058, T066, T067 1. Turn the cartridge around with the ink outlet(s) of the

cartridge upwards, use the enclosed adhesive tape to seal the outlet(s) tightly, then turn the cartridge back again and put it onto clean tissue paper.

2. Use the enclosed drill to drill a hole on the top of the cartridge (Fig. C01A)

3. Push the needle into the cartridge of the corresponding color refill hole. When you reach the bottom, pull the needle back up again for 1-2mm and slowly inject the appropriate amount of ink (Fig. C01B)

4. After refilling, let the cartridge rest for a while in this position before removing the seal tape.

5. Carefully use tissue to absorb any unnecessary ink around the ink outlet, then install the cartridge into printer and start the print menu.

REFILL CATEGORY 2 EPSON : SO20118, SO20122, SO20126, SO20130, SO20143, SO20147 BROTHER : LC03 1. Stick the needle 10-20mm deep into the cartridge through the

hole of the ink outlet. Do not try to push the needle in any deeper ; otherwise it may damage the ink bag inside. Then inject the appropriate amount of ink.(Fig.C02A)

2. After refilling the cartridge, let the cartridge sit for a while, then install the cartridge into the printer and start the print menu.

REFILL CATEGORY 3 CANON : BC02, BC05, BC06, BC20, BC22, BC23, BX-2 LEXMARK : 10N0016, 1380620, 12A1145, 12A1970, 12A1975, 13400HC, 1380490, 1380630, 1382050, 15M0100, 15M0360, 16G0055, 17G0050, 18L0032E, 18L0032, 18C0032E, 18C0032 1. Put your empty cartridge on some tissue paper

and use the drill to drill a refill hole right next to the air vent hole (C03A, C03B, C03C).

2. Push the needle into the chamber of the corresponding refill hole. When you reach the bottom with the needle, then pull it back up by 2-3mm and slowly inject the appropriate amount of ink.

3. Pump air into the refilling hole until one drop of ink comes out of the nozzles (for Lexmark cartridges, you can ignore this step. 4)

4. Carefully use tissue to absorb any unnecessary ink around the ink outlet, then install the cartridge into printer and start the print menu.

REFILL CATEGORY 4 CANON : BCI-10, BCI-11, BCI-15, BCI-16, BCI-21, BCI-21E, BCI-24, BCI-61, BCI-62, CLI-36 1. Put your empty cartridge on clean tissue paper with

the ink outlet(s) showing upwards (Fig.C04A). 2. Put the needle into the outlet, but do not push the

needle into the wick plug of the outlet. 3. Drop the ink down to the wick by squeezing bottle

gently. 4. Carefully use tissue to absorb any unnecessary ink

around the ink outlet, then install the cartridge into printer and start the print menu.

REFILL CATEGORY 5 CANON : BCI-3, BCI-3E, BCI-5, BCI-6, BCI-8, BJI-201, PGI-5, CLI-8, PGI-220, PGI-221, PGI-520, PGI-521 EPSON : SO20047, SO20049, SO20097 HP : n°178, n°364, n°564, n°862 XEROX : 8R12728, 8R7660, 8R7661, 8R7662, 8R7663 1. Seal the ink outlet with the enclosed adhesive tape. 2. Put your empty cartridge on clean tissue paper & use the

drill to drill a refill hole through the cover of the chamber without foam (Fig.C05A)

3. Insert the needle carefully into the refill hole and slowly inject the ink until the ink chamber without the foam is full.

4. Let the cartridge sit idle for a while 5. Remove the adhesive tape from the ink outlet(s) and

clean it with clean tissue paper, then install the cartridge into your printer and start the print menu.

REFILL CATEGORY 6 HP : 51626A, 51629A, 51633A, C1843A, C6614A 1. Seal the air vent hole on the bottom of the cartridge

with the enclosed adhesive tape (Fig.C06A). 2. Put your empty cartridge on clean tissue paper and

use the drill to drill a refill hole through the over (Fig. C06B)

3. Insert the needle carefully into the drilled refill hole and slowly inject 25ml of ink into the chamber.

4. Seal the refill hole with the attached adhesive tape. 5. Put the cartridge onto tissue paper, then with the

nozzles downwards, use the air pump to pump air into the cartridge to 5 times (Fig. C06C)

6. Absorb any ink at the nozzle surface with tissue paper and then remove the tape off the air vent hole on the bottom of the cartridge.

7. Let the cartridge sit for around 15-20 seconds with the print nozzles showing downwards. Do not install the cartridge into your printer before you ensure that no more drops of ink are coming out.

REFILL CATEGORY 7 HP : 51641A, C1823A, C3844A, C3845A, C6578A, C6625 1. Put your empty cartridge on clean tissue paper. Use the

ball pushing tool to push the small ball plug of the refill hole into the cartridge. The ball inside will not affect the performance of the cartridge (Fig. C07A)

2. Carefully insert the needle into the refill hole of the corresponding color chamber and slowly inject the appropriate amount of ink into the chamber.

3. Put the cartridge on tissue paper ; push the air blower hard into the refilling hole. Squeeze the pump bottle until ink comes out of nozzles. Sip up the ink at the nozzles with tissue paper and then install the cartridge into cartridge into printer & start the print menu.

REFILL CATEGORY 8 HP : C6615A, 51640A, 51640C, 51640M, 51640Y, 51644Y, 51644C, 51644M, 51645A 1. Remove the tap of the refill hole and use the ball pushing

tool to push the steel ball into the cartridge. The ball inside will not affect the performance of the cartridge (Fig, C08A)

2. Carefully insert the needle into the refill hole and slowly inject approximately 40ml of ink.

3. After refilling the cartridge, absorb any unnecessary ink around the refill hole with clean tissue paper and then seal the refill hole with the enclosed steel ball.

4. Let the refilled cartridge sit for about 15 minutes with the nozzle showing downwards. It is normal that some ink will come out of the nozzles in order to balance the internal air pressure.

5. As soon as the ink stopped coming out, absorb any unnecessary ink at the print nozzle surface with clean tissues paper, then install the cartridge into your printer and start the print menu.

REFILL CATEGORY 9 HP : C1816A, C8766EE, C9352AE, C9363EE, 51625A, 51649A LEXMARK : 12A1980, 1361760, 1380619, 12A1140, 10N0026, 12A1985, 13619HC, 1382060, 15M0101, 15M0120, 15M0125, 15M0360, 15M0370, 16G0065, 17G0060, 18L0042, 18L0000 1. Put your empty cartridge onto clean tissue paper.

Carefully remove the cap of the cartridge with a knife, making sure you do not cut off the clip of the cartridge (Fig.C09A). Note : Be careful not to hurt yourself with the knife.

2. Carefully insert the needle of the syringe into the refill hole of the corresponding ink chamber and slowly inject the ink into the cartridge until some ink drops come out of the print nozzles.

3. Put the cartridge cap back onto the cartridge and stick it on firmly (Fig C09B)

4. Install the cartridge into the printer, let it sit idle inside the printer for around one hour and then start printing.

REFILL CATEGORY 10 CANON : BC03, BX-3 1. Put your empty cartridge onto clean tissue paper and

use the ball pushing tool to push the steel ball into the cartridge. The ball inside will not affect the performance of the cartridge (Fig. C10A)

2. Carefully insert the needle into the refill hole and slowly inject the appropriate amount of ink into the corresponding ink chamber.

3. Absorb any unnecessary ink around the refill hole with clean tissue paper and then tightly seal the refill hole with attached adhesive tape.

4. Turn the cartridge upside down to keep the air hole upward (Fig. C10B)

5. Use the air pump to blow air into the air hole until a drop of ink comes out of the print nozzles. Carefully absorb the ink with clean tissue paper.

6. Install the cartridge into the printer and start the print menu.

REFILL CATEGORY 11 HP : C4841A, C4842A, C4843A, C4844A 1. Cut the label on the cartridge from the joint between the

cover and base with a knife and take off the cover (Fig. C11A)

2. Remove the rubber sealing plug from the refill hole with the tip of knife. Note: Be careful not to hurt yourself with the knife.

3. Carefully insert the needle into the refill hole. Be careful not to pierce the ink bag inside the cartridge. Slowly inject the appropriate amount of ink into the ink bag.

4. Seal the refill hole with the original rubber plug and then close the cover.

5. Let the cartridge sit for a while and then install it into the printer and start the print menu.

REFILL CATEGORY 12 BROTHER : LC02, LC04, LC21, LC31, LC50, LC600, LC700, LC800 1. Seal the ink outlet with the attached adhesive tape

(Fig. C12A) 2. Take off the cartridge cover of the cartridge with a

knife. Note: Be careful not to hurt you with the knife. 3. Remove the big silver seal tape and use the drill to

enlarge size of the refill hole of the ink chamber with foam inside (Fig.C12B)

4. Carefully insert the needle into the refill hole of the chamber with foam inside and slowly inject approximately 7ml of ink.

5. After refilling the cartridge, absorb any unnecessary ink around the refill hole with clean tissue paper, then seal the refill hole with the enclosed adhesive tape and assemble the cover.

6. Let the cartridge sit for a while and then install it into the printer and start the print menu.