Routes to VOC-compliant alkyd coatings - Perstorp · 314 Surface Coatings International Issue...
Transcript of Routes to VOC-compliant alkyd coatings - Perstorp · 314 Surface Coatings International Issue...
Surface Coatings International Issue 2008/6312
Alkyd resins are typically produced bythe condensation polymerisation ofnatural oils or fatty acids with
polyhydric alcohols such as pentaerythritol,glycerol or trimethylolpropane, and dibasicacids such as phthalic anhydride andisophthalic acid. Since natural oils and fattyacids are renewable raw materials andpolyhydric alcohols can be produced fullyor partly from renewable raw materials,alkyd resins represent a very ‘green’ binderselection compared with acrylic binders,whose building blocks are currently derivedfrom mineral oil.Pentaerythritol can easily be made from
renewable resources, as it is made from thealdehydes of methanol and ethanol (seeFigure 1). The main environmental problemwith alkyd resins is therefore that they aretypically used in diluted form in organicsolvents.Organic solvents can be hazardous at
many levels, both locally during themanufacture of the solvent and paint, andwhen the paint is applied and dried.Globally, volatile solvents can cause harmto the environment in the form of ozonedepletion. It is therefore very important tominimise the use of volatile content incoatings. Such a shift of technology is alsoenforced in the EU countries by theprovisions of the VOC (or ‘Decopaint’)directive. These provisions limit the amountof solvents that can be used in variousdecorative paints. The limits for differentapplications are given in Table 1.The suggested routes to VOC-compliant
coatings, high-solids resins and alkydemulsions, present a number of technicalchallenges such as drying performance,final hardness or solvent resistance. Somefindings are presented from work aimed atimproving the properties of resins for theseapplications by the use of technologiessuch as:
l molecularly tailored resins;l reactive surfactants for internal
stabilisation;l urethane alkyd emulsions;l alkyd-acrylic hybrids.
Over the years, many reactive diluentshave been proposed but have had limitedsuccess because they have not metperformance requirements or because ofenvironmental considerations. Reactivediluents based on allyl ethers, for example,are unsuitable for oxidative drying alkydsdue to the emission of acrolein.Linear polymers create viscous products
through chain entanglement, and theviscosity rises smoothly in proportion totheir molecular weight, according to theMark-Houwink equation (see Figure 2 andEquation 1).
Examples of resin formulation and paintperformance are given.
High-solids alkyds –molecular engineeringHigh-solids alkyds are reported to havebeen produced by various methods, forexample by using special molecular designand reactive diluents. The classical methodis to reduce the molecular weight and/orincrease the oil length, but this will giveinferior coating properties.
MethanolCH4O
Molecular weight 32.04
AcetaldehydeC2H4O
Molecular weight 44.05
FormaldehydeCH2O
Molecular weight 30.03
PentaerythritolC5H12O4
Molecular weight 136.15
EthanolC2H6O
Molecular weight 46.07
H H
0±± OH
OH
OHOH
OH
0OH
Fermentation
Figure 1: Biochemical route to pentaerythritol
Routes to VOC-compliant alkyd coatingsK Sörensen
Perstorp Specialty Chemicals AB, R&D, Application Development and Support, SE-284 80 Perstorp, Sweden
Table 1: Selected provisions of the EU VOC directive
Product subcategory Type Phase I (g/l) Phase II (g/l) (from 1.1.2007) (from 1.1.2010)
A Interior matt walls and ceilings WB 75 30(Gloss ≤25@60°) SB 400 30
B Interior gloss walls and ceilings WB 150 100(Gloss >25@60°) SB 400 100
C Exterior walls of mineral substrate WB 75 40SB 450 430
D Interior/exterior trim and cladding paints WB 150 130for wood and metal SB 400 300
E Interior/exterior trim varnishes and wood stains, WB 150 130including opaque wood stains SB 500 400
F Interior and exterior minimal build wood stains WB 150 130SB 700 700
313Surface Coatings International Issue 2008/6
[η]= K*[Mw]a Equation 1
Where η = viscosity, K is a constant andMW the molecular weight.Hyperbranched and dendritic polymers
deviate from this proportionality and havea lower viscosity than anticipated at highermolecular weights due to reducedentanglement and a low hydrodynamicvolume.The viscosity of an alkyd resin is also a
function of free volume availability. Thefree volume of a material is the sum of thespaces or holes that exist between themolecules of a material resulting from theimpact of one molecule or one moleculesegment striking another. These holes openand close as the molecule vibrates.At temperatures above the glass-
transition temperature (Tg), the holes arelarge enough and last long enough formolecules or molecular segments to moveinto them, resulting in a low viscosity. Freevolume increases as the temperatureincreases, and the rate of volume increaseis higher above the Tg or if a solvent isused.1
Alkyds made from glycerol are very linearin nature and it is difficult to build up highmolecular weights with oil lengths suitablefor decorative paints so as to provide highlevels of coating properties. This isovercome by using a higher functionalpolyalcohol such as pentaerythritol. Thesepenta alkyds have improved drying andcoating properties, but their viscosityincreases due to their higher molecularweight and broad molecular weightdistribution.One option for designing a high-solids
alkyd involves, for instance, replacingpentaerythritol with di-pentaerythritol (di-penta). Di-penta is a unique polyol with ahigh functionality, six primary hydroxylgroups, and with good heat and UVstability. The highly branched, densestructure of di-penta facilitates theformulation of alkyds with high solidscontent in combination with good dryingcharacteristics.Another option is to use the hydroxylic
acid dimethylol propionic acid (Bis-MPA)that will self-condense to producebranched structures with a lower viscosityat the same molecular weight comparedwith more linearly formulated counterparts.The example in Table 2 shows a pure
aliphatic alkyd, but partial application ofthis technique could also be considered innormal formulations. The second approach
can be taken to an even higher level toproduce hyperbranched alkyds in whichmost of the molecular weight is containedwithin the globular structure of themolecule (see Figure 3).In practice, such a hyper-branched alkyd
can be made by modifying the commercialhyperbranched product Boltorn H20 withfatty acids. Such a product is available asBoltorn U3000. In Table 2, alkydformulations are presented where di-pentaand bis-MPA replace penta and other alkydcomponents to produce high-solid alkyds.
Alkyd synthesis
Except for the standard alkyd, which wasproduced by the fusion process, the alkydsyntheses were carried out according to thestandard alkyd process at 240°C, withxylene as the azeotropic solvent, which wasultimately distilled off in a vacuum.Calculated and measured characteristics ofthe alkyds are given in Table 3. From thetable, it is clear that alkyds with very lowviscosity can be obtained by usingspeciality polymers in alkyd formulations.
Paint and paint performance
The alkyds shown in Table 3 were used indifferent white high-gloss paintformulations, as shown in Table 4. However,the di-penta alkyd has so far only beenevaluated as a clear coat. The paints werethen evaluated for drying performance andgloss. The di-penta alkyd and thehyperbranched version met the VOCrequirement for 300g/l max for trim paints.The paint performance study is also
presented in Table 4 and shows that high-gloss paints can be formulated using bis-MPA, di-penta or Boltorn alkyds. In all ofthese cases, the paints are softer than thecomparable alkyd, but gloss hold-out onweathering was better on the bis-MPA andthe Boltorn alkyds than the standard. Thedi-penta alkyd exhibited very good dryingand hardness development, closer to thestandard alkyd, although still onlymeasured as a clear coat.
Log v
isc
Log Mw
[η]= K*[Mw]a
Linear polymers
Dendrimers
Figure 2: Viscosity of dendrimers departs from the Mark-Houwink equation at high molecular weights
Table 2: Bis-MPA, di-penta and ‘concept’ alkyd formulations
Ingredient Standard alkyd Bis-MPA alkyd Di-penta alkyd Concept alkyd
Tall oil fatty acid 62.20 69.91 62.25 75.04Phthalic anhydride 23.88 – 14.13 9.89Pentaerythritol mono grade 20.42 – –Di-pentaerythritol – – 21.84 16.62Benzoic acid – – 8.38Bis-MPA – 39.56 – 4.48Total charge 106.50 109.47 106.60 106.03Water of reaction (g) 6.50 9.47 6.60 6.03
Surface Coatings International Issue 2008/6314
High-solids alkyds –reactive diluentsThe findings above indicate that it ispossible to produce alkyds having very lowviscosity with a low solvent content. Thehyperbranched alkyds can be used asreactive diluents in a standard alkyd tomeet the VOC requirement regarding trimpaints. However, due to their aliphaticnature, they create soft films, which is whysome applications definitely requiredifferent formulations to meet therequirements. Can it be possible to designan alkyd giving fast drying, hard films and
low viscosity when mixed with a standardalkyd?One possible method of improving
hardness and physical drying might be toincorporate hard segments with areasonable Tg shielded by softer segmentsand still maintaining a high molecularweight (see Figure 4). The shielding isnecessary to provide the low viscosity,while the architecture itself must allow fora free volume sufficient to give areasonable application viscosity.One approach involves the combined use
of di-penta and bis-MPA in the same alkyd.By applying a smart molecular design and
step-by-step synthesis, where the di-pentais partly fatty acid-functionalised and thebis-MPA is used to make hard segmentsthat are primarily linearly spaced, togetherwith phthalic anhydride between the partlyfatty acid-functionalised di-pentamolecules, a low viscosity resin is producedthat is very well suited for use as a diluterfor high-solids resins. The formulation ofsuch a resin is presented as the 'conceptalkyd' in Table 2.
Alkyd synthesis
The alkyd synthesis was carried outaccording to the normal method for alkyds,with xylene as the azeotropic solvent. Forthe concept alkyd, the reaction was carriedout in three steps. In the first step, thefatty acid was reacted with the di-penta toan acid number of 3mg KOH/g at 220°C.Phthalic anhydride was added in a secondstep and reacted at 160°C, then held untilthe anhydride ring opened on the coreester.In a third step, the bis-MPA was reacted
in portions at 160°C. The alkyd was thenrun at 200 to 210°C until the desired acidnumber was reached. The low reactiontemperature was chosen to minimise thereaction of the tertiary carboxyl group ofbis-MPA. Calculated and measuredcharacteristics of the concept alkyd aregiven in Table 3. From the table, it is clearthat an alkyd with very low viscosity can beobtained.
Lacquers and lacquer performance
Lacquers were produced from the standardalkyd in Table 2 and the concept alkyd, andas a resin mix where the concept alkyd andthe standard alkyd were mixed. Thelacquers were formulated to have the sameviscosity. As shown in Table 5, the VOC ofthe diluted resin was considerably lowerthan that of the standard alkyd and metthe requirement for category D in the VOCdirective for 300g/l max.Lacquer performance is shown in Table 5,
which reveals that drying was just as goodin the diluted alkyd as in the standard. It isour belief that this concept could be usedwith many conventional alkyds and itcould, as such, act as a good tool for resinproducers for producing binders suitablefor paints that comply with therequirements for 2010.
O
O
O
O
O
O
OO
O
O
O
O O
O
O
O
O
O
O
OO
O
O
O
O
HO
O
O
O
OHHO
O
O
Boltorn
HOHO
HOHO
HO
HO HO
HO
HO
HO
HO
HO
HO
OHHO
HO
HOHO
HOHO
HO
HO
OH
HO
OH OHOH
OH
OH OH
OH
OO
O
OO O
OO
O
O O
O
O
OO
O
OO
OO
OO
O
O
OO
OO
O
O
O
O O O
OOO
OO O
OO
OO
OO
O O
OO
O
O O OO
OO
OO
O
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH OH
HO
HO
OH
OH
Pentaerythritol
HO
HO
OH
O OH
OHOH
Di-penta
OH
HO
OHOH
HO
OH
OH
OH
O
O O
O
O
Bis-MPA hyperbranched
O
Figure 3: Some molecules that will yield branching and dense structures
Alkyd emulsionsAlthough high-solids alkyds may be used tomake VOC-compliant alkyd coatings, thesewill, in most cases, still contain solvents. Aswitch from diluting with solvents todiluting with water might therefore be aneven better solution from an environmentalstandpoint. Alkyd emulsions can be madeusing no, or virtually no, solvents.A frequently recommended method for
producing alkyd emulsions is the inversionprocess in which water is added to thealkyd until a critical volume concentrationof water is reached, and a phase transferfrom a water-in-oil emulsion to an oil-in-water emulsion takes place (see Figure 5).In the emulsification processes, the alkyd
droplets formed have to be stabilised bysome means. This can typically be achievedusing external emulsifiers (surfactants) orincorporating internal stabilising groups inthe polymer chain. Examples of these arepolyethylene oxide chains or ionisablegroups such as carboxyl groups fromtrimellitic anhydride (TMA) or dimethylolpropionic acid (bis-MPA). A combination ofnon-ionic polyethylene chains and anionicstabilising moieties is also possible.All techniques have their benefits and
drawbacks. When using externalemulsifiers, there is a risk of surfactantmigration within the finished film, causingsurface defects such as poor gloss,tackiness or whitening due to waterabsorption. Migration of molecules can bereduced or avoided by choosing toincorporate internal stabilising groups, butthis type of stabilisation requires extrasteps during alkyd synthesis.It has been explained elsewhere how such
an internally stabilised alkyd emulsion canbe produced to make high-gloss paints byfirst creating an adduct between TMA andMPEG.2 These paints were rather soft dueto the relatively high number ofhydrophilic ethoxylate chains needed toprovide the emulsion stability. Althoughhaving high water resistance, they did nothave a high chemical resistance, which iswhy some applications could be moredifficult to address with such resins. It istherefore of interest to show howinternally stabilised alkyd emulsions can beimproved in respect of their hardness andchemical resistance.In solvent-borne alkyd coatings, small
quantities of isocyanates are often used toimprove the chemical and outdoorresistance of the alkyd. This kind of
modification can also be applied to analkyd emulsion, although the highviscosities of these resins make thesynthesis and emulsification of the resinssomewhat tricky.Another way to improve alkyd emulsions
may involve the addition of smallquantities of acrylic dispersions to producephysical blends. This modification will
affect properties such as hardness anddrying speed in particular.
Emulsifiable alkyd resinsIn Table 6, the alkyd formulations of twointernally stabilised alkyds are given: onewithout urethane modification and one
Table 4: Paint compositions and basic properties of bis-MPA, di-penta and Boltorn alkyds
Ingredients and test Standard alkyd Bis-MPA alkyd Di-Penta alkyd Boltorn alkydprocedures
Standard alkyd 60% 57.36 – – –Bis-MPA alkyd 100% – 51.04 – –Di-penta alkyd 100% – – 71.21 –Boltorn alkyd – – – 50.54TiO2 26.90 41.47 – 40.42Zr-Octoate, 12% 0.84 1.05 1.45 1.05Co-octoate, 12% 0.24 0.3 0.35 0.30Ca-octoate, 10% 0.40 0.84 0.70 0.27Exkin 2 0.30 0.27 0.09 –Fungicide 0.30 1.38 – –White spirit 13.66 – – –Exxsol D40 – 3.65 26.20 7.42Total 100 100 – 100
PVC 17% 16% 0% 17%Viscosity, cone and plate 350 380 500 350(25°C) (mPas s)Viscosity (23°C) DIN-cup 4 (sec) – – – –Calculated VOC (g/l) 430 74 265 119
König pendulum hardness 1 day 24 43 22 437 days 56 23 35 421 to 6 months 104 23 69 35Initial gloss at 60° 90 87 NA 82Dry film thickness (µm) 25 25 25 45
Table 3: Characterisation of the bis-MPA, di-Penta, Boltorn and ‘concept’ alkyds
Standard Bis-MPA Di-Penta Boltorn Conceptalkyd alkyd alkyd alkyd alkyd
CalculatedOil length 65 73 65 75 78.4Acid number (mg KOH/g) 9 7 8 10 15 (15.7*)Hydroxyl number (mg KOH/g) 43 36 30 15 32 (35*)Mw (g/mole) 20422 8016 20739 6500 3945
MeasuredViscosity (23°C) 100% by wt (mPas) – 780 42000 1200 2690Viscosity (23°C) 60% by wt 5200 – – –(white spirit) (mPas)Colour (Gardner) 6 8 9 7 8* Experimentally determined value
315Surface Coatings International Issue 2008/6
Surface Coatings International Issue 2008/6316
with. In both alkyds, an adduct oftrimellitic anhydride (TMA) and mono-methyl ether of a polyethylene glycol(MPEG 750) are used to incorporatependant MPEG chains into the alkyd resin.
Adduct and alkyd synthesis
The adduct was prepared by reacting TMAand MPEG 750 in a molar ratio of 1.05:1 at170°C for five hours, purely to open theanhydride ring. GPC (gel permeationchromatography) characterisations of theresulting adduct show that single MPEG750 substitution on the TMA molecule wasthe most frequent substitution. Triplesubstitution was not observed.The alkyd synthesis of the internally
stabilised alkyd was performed by a fusionprocess. All step one components wereadded to the reactor and condensationtook place at 230 to 240°C. When the acidnumber reached around 30mg KOH/g, thereactor was cooled to 180°C prior toadding the dispersing adduct, which wasreacted into the resins at 215°C.In the case of the unmodified alkyd, the
reactor was maintained at 215°C until thedesired acid number of 20mg KOH/g wasreached. In the case of the urethane alkyd,the resin was reacted to an acid numberbelow 5mg KOH/g prior to cooling it to80°C. At that temperature, the isocyanatewas added drop-wise and the reactor wasmaintained at 80°C until titration of theurethane content showed that the reaction
Table 5: Lacquer formulations and basic properties, including ‘concept alkyd’
Lacquer formulation Standard alkyd Diluted alkyd Concept alkyd
Standard alkyd resin, 75% in white spirit 100 60 –Concept alkyd, 100% – 40 100Co-octoate, 10% 0.46 0.52 0.6Zr-Octoate, 12% 1.56 1.78 2.08Ca-octoate, 10% 0.76 0.86 1Exkin 2 0.14 0.12 0.12Aromatic-free white spirit 29.8 22.08 20.38
Lacquer characteristicsNon-volatile content, % 56.9 68.11 80.4Viscosity, 25°C, mPas 480 480 490Calculated VOC, g/l 391 295 178
König pendulum hardness1 day 14 20 187 days 33 42 2014 days 53 54 2828 days 74 65 3149 days 88 74 40Dry film thickness (µm) 40 40 40
Table 6: Formulations of alkyds for emulsification
Ingredients Internally Internallystabilised stabilisedalkyd urethane
alkyd
Step oneBenzoic acid 3.4 3.69Pentaerythritol 21 23.36Phthalic anhydride 23.46 12.5Tall oil fatty acid 58.19 65.16Acid number (mg KOH/g) 30 30OH-value (mg KOH/g) 69.1 177Calculated Mw (g/mol) 2024 709
Step twoDispersing adduct 11.26 10Acid number (mg KOH/g) 20 <5OH-value (mg KOH/g) 43.7 124Calculated Mw (g/mol) 4648 1406
Step threeIsophorone diisocyanate – 11.04
High Tgsegment
Low Tg
O
O
O
O
O
O
O
O
O O O O O
OH OH
HO OO
O O
OO
O OH
OH
Figure 4: Concept of using a reactive diluent to combine high and low Tg segments in a molecule
was finished. Characteristics of the alkydsare shown in Table 7.
Alkyd emulsification
Alkyd emulsions were prepared using thephase inversion process in which water isadded progressively to the molten resincontaining emulsifiers. A water-in-oilemulsion is formed initially which, at acritical solids content, will phase reverseforming an oil-in-water emulsion. Theformulations for the alkyd emulsionsproduced are presented in Table 8.Some external anionic emulsifiers were
added to both emulsions because theywould otherwise rely only on non-ionicstabilisation. It is generally accepted thatanionic and non-ionic stabilisation shouldbe combined for best overall performance.The alkyd emulsion characteristics are alsoindicated in Table 8, showing good stability,low viscosity and a reasonably low dropletsize.
Lacquer performance
To the alkyd emulsions was added 1.5% byweight of the combination drier AdditolVXW. Coatings were drawn down on glassusing a 150µm applicator, and hardnessdevelopment and covered spot resistancewere tested. The hardness developmentshown in Table 8 reveals that the urethane-modified coating developed hardness muchfaster than the unmodified coating, and itsultimate hardness was also higher.
Water and chemical resistance weremeasured by covered spot testing on filmsapplied to glass panels after four weeks at23°C, 50% relative humidity, and for a dryfilm thickness of approximately 50µm. InTable 8 the resistance values are alsopresented, using the following grading scale:
5 = no visible change;4 = minor variation in gloss or barely
visible marks;3 = weak mark;2 = substantial mark;
1 = the structure of the surface has changedor has been partly or complete removed.
From the table it is clear that the urethanemodification gave better ethanol resistanceand it may be of interest to find a furtherapplication for this improved chemicalresistance.
Alkyd-acrylic hybridsAcrylic emulsions are widely used incoatings due to properties such as highhardness, fast drying and good gloss hold-
Table 8: Alkyd emulsion lacquer formulations and characteristics
Formulation Internally stabilised Internally stabilised alkyd – emulsion urethane alkyd – emulsion
Alkyd 49.6 49Anionic surfactant 0.3 1Defoamer 0.5 –Water 49.6 50Total 100 100
Storage stability, 1 week at 50°C OK OKDroplet size D(0.5) (µm) 0.8 1.1Viscosity (23°C) (mPa s) 49 85
König pendulum hardness 1 day 11 117 days 13 1714 days 15 2421 days 17 3828 days 18 47
Spot testing resistanceWater 6 hours 4 4Water 6 hours, recovered 5 5EtOH (48%), 30 min 1 3EtOH (48%), 30 min, recovered 5 5
Table 7: Characterisation of the alkyds preparedfor emulsification
Properties Internally Internallystabilised stabilisedalkyd urethane
alkyd
Calculated propertiesOil length (%) 55 57Acid number (mg KOH/g) 20 0Hydroxyl number 44 66(mg KOH/g)Mw (g/mole) 4649 4369
Measured propertiesAcid Number (mg KOH/g) 20.4 3.1OH-value (mg KOH/g) 44 70Mw 16756 12500Mn 2221 3289Polydispersity 7.54 3.8Viscosity (125°C) 460 894100% by wt (mPas)Colour (Gardner) 7.0 7.6
A = alkyd
Fraction of water (% by weight)Vis
cosit
y
A
DC
B
B = water droplets in oil (alkyd)C = coalescing water dropletsD = oil−in−water emulsion
Figure 5: Schematic representation of the emulsion inversion process
317Surface Coatings International Issue 2008/6
Surface Coatings International Issue 2008/6318
out on weathering. However, acrylicscannot always match the performance ofalkyds in terms of open time, self-primingand the chemical resistance deriving fromthe oxidative cross-linking of the fatty acidcomponent in the alkyd. Cost is also afactor, the alkyd being typically cheaperthan the acrylics.Alkyds and acrylics can be combined to
make so-called hybrids. There are severalways to make these hybrids such aspolymerising the acrylic in the alkydemulsion, emulsifying the alkyd in theacrylic, or by simply blending the acryliclatex with an alkyd emulsion. The last willbe presented here to see what synergisticfeatures are available.Table 9 shows some alkyd acrylic
formulations. Both pure acrylic and styreneacrylic dispersions were tested. The physicalblends are produced simply by mixing theacrylic latex into the internally stabilisedalkyd emulsion at low shear and slow rateof addition. A suitable amount ofcoalescent agent has to be added in orderto ensure a good film formation. Theblends are very stable over time and do notvary in terms of either pH or viscosity.A combination drier was added to the
hybrids and the alkyd emulsion to obtainclearcoat formulations for evaluation.Clearcoats were applied to glass using a200µm applicator bar and coatingperformance was evaluated.Table 9 also shows the hardness
development of the coatings, revealing thatthe hardness of the hybrids is higher thanthat of the pure alkyd emulsion. The dryingtimes recorded by a Beck-Koller dryingrecorder also show that the small additionof acrylic or styrene-acrylic latex to thealkyd emulsion results in faster surfacedrying. The gloss on coated black glass at20° and 60° is very good for the pure alkydemulsion, whereas the hybrids both havesomewhat lower gloss. This could possiblybe due to a slightly excessive amount ofacrylic as too high an amount may give riseto compatibility problems.
Acrylic and styrene acrylic dispersions canthus be used to modify the coatingproperties of alkyd emulsions to addressissues such as hardness or drying time. Thestyrene-acrylic hybrid has a much betterappearance than the acrylic hybrid, and itis believed that upon film formation, thearomatic nature of the phthalic anhydrideof the alkyd and of the styrene acrylichelps to produce a good blend at a
molecular level. This statement, however,requires further evidence.
ConclusionsHigh-solid alkyds, diluent resins, alkydemulsions and hybrids have been described,all giving coatings with VOC levels belowthe limits stipulated in the VOC legislationfor 2010. Thus, environmentally-friendlycoatings can be produced by adapting thewell-established alkyd resin technology indifferent ways. Alkyd resin technology isvery versatile, and when combining it withother chemistry, the possible combinationsto be tested are limited only by theimagination of the developer.
AcknowledgmentsThis work would not have been possiblewithout the assistance of my co-workers,Anders Clausson, Olivia Karlsson, RebeckaLiedholm, Marie Westerblad and JosefinZackrisson in Perstorp Specialty ChemicalsAB in Sweden, and Vrijesh Singh and SRamakrishnan at Perstorp India, whosecontributions are gratefully acknowledged.
References
1. Manea M, A Clausson, S Stigsson
and K Sörensen, ‘High-solids alkyd
strategy’, Paint and CoatingsIndustry, 28–36, August 2007
2. Ziegler G, R Liedholm, G Ziegler, C
Skoog, M Westerblad and K
Sörensen, ‘Different stabilizing
technologies for alkyd emulsions
and their effect on coating proper-
ties’, Proceedings from the Water-
borne and High-solids Coatings
Conference, Brussels, March
2006
Table 9: Hybrid coating formulations anddevelopment of their physical properties overtime. Drying on glass panels at 23°C and 50%relative humidity
Formulation and Alkyd Acrylic Styrene test procedures emulsion hybrid acrylic
hybrid
Alkyd emulsion 100 90 90Acrylic – 10 –Styrene acrylic – – 10Coalescing agent – 0.7 1
König pendulum hardness1 day 11 10 97 days 13 16 1614 days 15 30 2621 days 17 34 3128 days 18 41 33
Beck-Koller drying times, hoursDust free 1 0.5 0.5Tack free 3 1 2Through dry 9 2 4Hard dry 22 6 11
Gloss at 20°1 day 84 72 837 days 84 67 8214 days 81 71 7921 days 82 69 77
Gloss at 60°1 day 91 88 927 days 91 87 9214 days 91 88 9021 days 91 87 90