Roto NT Designo - Roto North America · 8 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to...
Transcript of Roto NT Designo - Roto North America · 8 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to...
Window and Door Technology
Roto NT DesignoConcealed hinge solution for windows and balcony doors with high sash weights up to 150 kg
Installation, maintenance and operation instructionsfor timber windows and balcony doors – 13 mm hardware axis
ImprintCopyright: February 2017
Roto Frank AGWindow and Door Technology
Wilhelm-Frank-Platz 1
70771 Leinfelden-Echterdingen
Germany
Phone +49 711 7598 0
Fax +49 711 7598 253
www.roto-frank.com
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 3
General information Information on these instructions ....................................................5
Responsibility of the target groups ..................................................6
Instruction obligation of the target groups ......................................7
Explanation of the safety instruction symbols .................................8
Limitation of liability ........................................................................9
Safety Stipulated use ................................................................................ 10
Stipulated application for end-users .............................................. 11
Safety instructions ......................................................................... 12
Safety information for end-users .................................................. 13
Fabrication advice .......................................................................... 14
Screw fixing ................................................................................... 15
Information on the product General hardware characteristics ................................................... 17
Introduction ................................................................................... 19
Frame clearance ............................................................................. 20
Dimensional data for hardware ...................................................... 21
Application diagram ....................................................................... 22
Hardware overview Explanation on the hardware overview chapter ............................. 27
Tilt&Turn hardware – Basic security .............................................. 28
......................... 30
................ 32
Tilt-First hardware – Basic security ................................................ 34
Turn-Only hardware – Basic security .............................................. 36
Tilt-Only hardware – Basic security ................................................ 39
............................ 40
............ 44
....... 48
possible combinations .................................................................. 52
possible combinations .................................................................. 53
Profile-related components ............................................................ 54
General informationContents
4 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Installation Drilling the sash drill-holes ............................................................ 57
Install the handle ........................................................................... 59
Drilling the frame drill-holes .......................................................... 60
Cropping the hardware components .............................................. 62
Installing sash hardware components............................................ 63
Installing the turn-restrictor ........................................................... 64
Installing an additional scissor stay ............................................... 66
Connecting sash and frame ........................................................... 68
Installing the load transfer device .................................................. 70
Adjusting the load transfer device ................................................. 71
Installation drawings Positioning of the frame components ........................................... 74
Jigs ............................................................................................... 86
Adjustment Explanation on the adjustment chapter .......................................... 88
Adjustment instructions ................................................................ 89
Operation Operating information .................................................................... 92
Operation information for end-users .............................................. 93
Troubleshooting ............................................................................ 94
Maintenance Maintenance .................................................................................. 96
Lubrication points .......................................................................... 97
Inspection and care ....................................................................... 98
Preservation of the surface finish .................................................. 99
Dismantling Unhinging the sash with load transfer device .............................. 101
Unhinging the sash without load transfer device ......................... 102
Transport Transport, packaging, storage ..................................................... 103
Transport inspection .................................................................... 104
Disposal ................................................................................................... 105
General informationContents
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 5
General informationInformation on these instructions
This manual contains important information, instructions and application dia-
grams (maximum sash si es and sash weights) as well as installation instruc-
tions regarding the further work of the hardware.
Also, this manual contains binding guidelines to ensure the duty to instruct
through to the end-user.
The information and instructions in this manual refer to the products of the
Roto NT hardware system.
Apart from these installation, maintenance and operation instructions, the
following documents apply:
Catalogue
Directives of the Quality Assurance Association: Locks and Hardware
(Richtlinie der tegemeinschaft Schl sser und eschl ge e. .)
irectives H E of the uality ssurance ssociation ocks and Hardware
(Richtlinie H E der tegemeinschaft Schl sser und eschl ge e. .)
This manual should be stored in such a manner that it can be quickly used, if
needed.
Additional markingsTo highlight handling directives, results, lists, references and other elements,
the following signs are used in this manual:
Marking Explanation
Sash
Frame
Drill-holes
1 Hardware components
1. Action steps
First level of the hierarchy in a list
– nordered list (second level of hierarchy)
P. 12 (Cross) reference in tables
Refer to page 12 (Cross) reference in the text
Abbreviation Explanation
SRW Sash rebate width
SRH Sash rebate height
S.kg Sash weight
Resistance Class 1
Resistance Class 2
All dimensions stated in mm.
Protection of copyrightThe contents of this manual are protected by copyright. In the framework of
the hardware manufacturing, the use of the contents is allowed. Any other or
further use is not permitted without written permission of the manufacturer.
6 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
The information in this document is aimed at the following target groups:
Hardware dealersThe “hardware dealers” target group includes all companies/persons who
purchase hardware from the hardware manufacturer to resell it without the
hardware being modified or subjected to further work.
Manufacturers of windows and balcony doorsThe “manufacturers of windows and balcony doors” target group includes all
companies/persons who purchase hardware from the hardware manufac-
turer or the hardware dealer and build it into windows and balcony doors.
The “building element dealers” target group includes all companies/persons
who purchase windows and balcony doors from the manufacturer of windows
and balcony doors in order to sell these on and to install them into a building
development, without the windows or balcony doors being modified.
The “installation company” target group includes all companies/persons who
purchase windows and balcony doors from the manufacturer of windows and
balcony doors, or from a building element dealer, in order to sell these and to
install them into a building development, without the windows or balcony
doors being modified.
BuilderThe “builder” target group includes all companies/persons who order win-
dows and/or balcony doors for installation into their building project.
End-usersThe “end-users” target group includes all persons who operate the installed
windows and/or balcony doors.
General informationResponsibility of the target groups
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 7
General informationInstruction obligation of the target groups
NOTE!Every target group must fully comply with its instruction obligation.
Unless defined otherwise in the following, the documents and infor-
mation may be transmitted e.g. as printed documents, CD-ROM, or
via Internet access.
Responsibility of the hardware dealerThe hardware dealer must transmit the following documents to the manufac-
turer of windows and balcony doors:
– Catalogue
– Installation, maintenance and operation instructions
– irective for fixing load bearing urn Only and ilt urn hardware compo-
nents ( )
– uidelines advice on the product and on liability ( H H)
– uidelines advice for end users ( H E)
Responsibility of the manufacturer of windows and balcony doorsThe manufacturer of windows and balcony doors must transmit the following
documents to the building element dealer or to the builder, even when a
subcontractor (installation company) is acting as an intermediary
– Installation, maintenance and operation instructions
– irective for fixing load bearing urn Only and ilt urn hardware
components ( )
– uidelines advice on the product and on liability ( H H)
– uidelines advice for end users ( H E)
He must ensure that the end-user is provided with the documents and
information intended for him, in printed format.
The building element dealer must transmit the following documents to the
builder, even when a subcontractor (installation company) is acting as an
intermediary:
– aintenance and operating instructions (with the focus on hardware)
– uidelines advice on the product and on liability ( H H)
– uidelines advice for end users ( H E)
Responsibility of the builderThe builder must transmit the following documents to the end-user:
– aintenance and operating instructions (with the focus on hardware)
– uidelines advice for end users ( H E)
8 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
General informationExplanation of the safety instruction symbols
In this manual, safety information is indicated by symbols. The safety informa-
tion is introduced by a key word that indicates the severity of the danger.
DANGER!This symbol in conjunction with the signal word indicates an immi-
nently hazardous situation, which could result in death or serious
damage to health if it is not avoided.
WARNING!This symbol in conjunction with the signal word indicates a poten-
tially dangerous situation, which could result in death or serious
damage to health if it is not avoided.
CAUTION!This symbol in conjunction with the signal word indicates a poten-
tially dangerous situation, which may lead to minor or light injuries
if it is not avoided.
NOTE!This symbol in conjunction with the signal word indicates a poten-
tially dangerous situation, which may lead to property or environ-
mental damage if it is not avoided.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 9
General informationLimitation of liability
All details and instructions in this document were compiled taking into ac-
count the relevant standards and regulations, the state of the art, and also
many years of knowledge and experience.
The hardware manufacturer accepts no liability for damages resulting from:
– Failure to comply with this document and all product-specific documents
and related applicable directives (refer to the chapters Safety and Stipu-
lated use).
– Non-stipulated use/misuse (refer to the chapters Safety and Stipulated
use).
– Insufficient invitation to tender, failure to adhere to the installation instruc-
tions or application drawings.
– Increased soiling.
Claims by third parties against the hardware manufacturer on the ground of
damages resulting from misuse or failure to follow the instruction obligation
on the part of the hardware dealer, the manufacturer of windows and bal-
cony doors, and of the building element dealer or the builder are transferred
accordingly.
The undertakings agreed in the delivery contract, the general conditions of
business and the delivery conditions of the hardware manufacturer, and the
legal regulations applicable at the time of concluding a contract are effective.
The warranty covers only original Roto components.
The right to technical modifications for the improvement of performance
characteristics and for further development is reserved.
10 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
SafetyStipulated use
urn Only and ilt urn hardware is one hand operation urn Only and
ilt urn hardware for windows and balcony doors in building construction.
This is used to enable windows and balcony-door sashes into a turning posi-
tion by operating a hand lever (handle) or into a limited tilting position in the
case of the scissors (sash stay) version. urn Only and ilt urn hardware is
used on vertically installed windows and balcony doors made of timber, C,
aluminium or steel and their corresponding material combinations. Turn-Only
and ilt urn hardware as covered by this definition, locks window and bal-
cony door sashes or enables various ventilating positions. When closing, the
gasket counter force must be overcome as a rule.
Correct use also includes adhering to all the specifications in the product-spe-
cific documents, such as:
– These installation, maintenance and operation instructions
– Product catalogues
– Information and specifications of the profile manufacturer (e.g. C or
light metal profiles etc.)
– he relevant directives and H E of the uality ssurance
Association: Locks and Hardware (Gütegemeinschaft Schlösser und
eschl ge e. .)
– The valid national laws and directives
Any type of use that goes beyond or differs from the defined correct use shall
be regarded as misuse.
WARNING!Danger from misuse!Misuse and incorrect installation of hardware can result in hazard-
ous situations.
– Never use hardware combinations that have not been approved
by the hardware manufacturer.
– Never use accessories that are not original products or that have
not been approved by the hardware manufacturer.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 11
SafetyStipulated application for end-usersurn Only and ilt urn hardware
or windows and balcony doors with urn Only and ilt urn hardware, win-
dow and balcony door sashes can be brought into a turn position or into
a limited tilting position by means of the scissor stay.
When a sash is closed and the hardware is locked, the resistance of a gasket
usually needs to be overcome.
WARNING!Danger of injury and material damage from incorrect closing and opening the sash!Incorrect closing and opening of sashes can result in serious injuries
and significant material damage.
Therefore:
– Ensure that when closing the sash, it does not collide with the
frame or with another sash.
– Ensure that the sash is guided slowly by hand throughout the
entire range of movement as far as the fully closed position, and
that it is brought very slowly towards the frame.
– Ensure that the sash never slams closed or swings open in an
uncontrolled manner.
Any use beyond or other than the stipulated application and installation of
the products is deemed to be misuse and can result in dangerous circum-
stances.
WARNING!Danger from misuse!Misuse of windows and balcony doors can result in dangerous
circumstances.
In particular, avoid the following applications:
– insertion of obstacles in the opening area between the frame
and the window or balcony door sashes,
– the deliberate or negligent application of excessive loads on
windows and balcony doors,
– deliberate or uncontrolled slamming or pushing of windows and
balcony doors against the window reveal. This can destroy the
hardware, frame materials, or other individual components of
the windows or balcony doors.
Claims for damages of any type whatsoever resulting of operation other than
that stipulated are excluded.
12 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
SafetySafety instructionsurn Only and ilt urn hardware, Safety relevant symbols
Comply with the following symbols and their meanings in order to avoid
accidents, injuries and material damage.
Symbol Meaning
DANGER!Danger of injury from falling through open windows and balcony doors.– Proceed cautiously in the vicinity of open windows and balcony
doors.
– Please keep children and persons that cannot appreciate the
danger away from the hazard area.
WARNING!Danger of injury through trapping of body parts in the open-ing gap between sash and frame.– When closing windows and balcony doors, never reach between
sash and frame, and always act with care.
– Please keep children and persons that cannot appreciate the
danger away from the hazard area.
WARNING!Danger of injury and material damage from overloading the sash– Refrain from additionally loading the sash.
CAUTION!Danger of injury from the effect of wind– Prevent wind from acting on the open sash.
– During wind and draughts, close and lock windows and balcony
door sashes.
CAUTION!Danger of injury and material damage from insertion of ob-structions into the opening gap between sash and frame– Refrain from inserting obstacles in the opening gap between the
sash and the frame.
CAUTION!Danger of injury and material damage from pressing the sash
– o not press the sash against the opening edge (reveal).
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 13
SafetySafety information for end-users urn Only and ilt urn hardware, Safety relevant symbols
The following symbols can by used on windows and balcony doors to protect
the end-user. Always keep these symbols in a clearly legible state. Please
order stickers separately (O R 16 E EN v1).
SicherheitshinweisSecurity advice
08/2012 OPR_16_DE-EN_v1
14 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
SafetyFabrication advice
Maximum sash sizes and weightsThe technical data, application diagrams, and component classifications in
the product-specific documentation of the hardware manufacturer give in-
structions on the maximum permitted sash si es and weights. Here, the
component with the smallest permitted load bearing capacity decides the
maximum permitted sash weight.
– Check compliance of the technical data, application diagrams, and compo-
nent classifications before the use of electronic data sets, and especially
their use in fenestration programmes.
– he maximum permitted sash si es and weights must never be exceeded.
In the case of uncertainty contact the hardware manufacturer.
Guidelines from the profile manufacturerThe manufacturer of windows and/or balcony doors must comply with all
specified system-related dimensions (e.g. gasket gap dimensions or locking-
point distances). urthermore, he must check these regularly and make cer-
tain of them, especially on the first use of new hardware components, during
manufacture, in an ongoing manner up to and including the window installa-
tion.
NOTE!The hardware parts must always be designed such that the system-
related dimensions - insofar as they are affected by the hardware -
can be adjusted. If a deviation from these dimensions is noticed
only after the installation of the windows, the hardware manufac-
turer is not responsible for any possible additional work arising.
Composition of hardwareBurglary inhibiting windows and balcony doors require hardware which fulfils
particular requirements.
Windows and balcony doors for damp rooms, and those for use in environ-
ments with aggressive and corrosive air components require hardware which
fulfils particular requirements.
The resistance of windows and balcony doors to wind loads when closed
and locked depends on the actual designs of the windows and balcony
doors. Wind loads prescribed by law and standards (e.g. as per EN 12210 –
especially test pressure 3) can be dissipated by the hardware system.
In general, the urn Only and ilt urn hardware defined in this document is
able to fulfil legal and standard requirements for barrier-free habitations.
The hardware combinations and installations appropriate for windows and
balcony doors in the previously mentioned areas should be specifically se-
lected and agreed with the hardware manufacturer and the profile manufac-
turer.
NOTE!The guidelines of the hardware manufacturer relating to the combi-
nation of the hardware (e.g. the use of additional stay arms, the de-
sign of hardware for burglary-inhibiting sashes for windows and bal-
cony doors, etc.) are binding.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 15
SafetyScrew fixing
DANGER!Danger to life from incorrectly installed and threaded hardware components!Incorrect installation and threading of hardware components can
result in dangerous circumstances and cause severe accidents,
even including death.
Therefore:
– For installation and especially for threaded components, observe
the product-specific documentation of the hardware manufacturer,
the information from the profile manufacturer, and all contents of
the TBDK directive of the Gütegemeinschaft Schlösser und
Beschläge.
or fixing the hardware components, Ø 3.9–4.2 x ... inc plated and passi-
vated steel fenestration screws are to be used. In the case of special climatic
conditions, use fenestration screws with additional sealing.
he window fabricator must ensure ade uate fixing of the hardware compo-
nents, consulting the screw manufacturer if necessary. When fixing security relevant, supportive hardware components such as stay bearings and
pivot rests, the tearing-forces vertical to the sash plane surface must be
reached in accordance with the following table (the tractive-force values
depend on the sash weights from the ).
Sash weight in kg Tractive force in N
60 1650
70 1900
80 2200
90 2450
100 2710
110 3000
120 3250
130 3525
140 3900
150 4200
1) Acceptable tolerance -10%
The stated values refer to the stay bearing. These are also valid for the pivot
rest if the fixing is carried out in the same manner as with the stay bearing.
On corrosive timber (i.e. af elia, oak etc.), the hardware s routed areas are to
be treated with a protective coating before installing the hardware in order to
protect the hardware.
Do not use any acid cross-linked sealing compounds that could lead to corro-
sion of the hardware components.
The glazing spacer-block regulations for the glazing procedure are to be
adhered to.
16 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
SafetyScrew fixing
Fixing suggestion installation of security windows
Screw fixing
Fixing SEC striker3 screws 4.0 x ...
Glazing-bead fixingor fixing the gla ing beads, use screws if re uired.
Screw fixing
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 17
Information on the productGeneral hardware characteristicsRoto N esigno urn Only ilt urn hardware system for windows and balcony doors
– Central locking system for one-hand-operation completely concealed in the
sash-rebate
– Profiled faceplate
– Effortless operation with low abrasion due to guided adjustable locking
cams
– Easy adjustment of the locking cams with standard tools
E cam gasket compression ad ustable eccentric cam and or
cam gasket compression ad ustable eccentric security cam and or
cam height and gasket compression ad ustable eccentric security cam
– Strong interlocking Clip it connection without loss of cam travel
– Link-slider guided stay arm, as standard with
– Integrated anti slam device (only version)
– Turn restriction
– ishandling device in tilted position (only version)
– Stay bearing and pivot rest completely concealed in the sash rebate
– High uality Roto Sil Nano surface finish (matt silvery) for maximum corro-
sion resistance ( IN EN 13126 8 Class 4) using Nano particles (free from
Chromium I compounds)
– 10-year warranty on the operativeness of the hardware
– 3D adjustment in stay arm / corner hinge / pivot rest
– Low-maintenance thanks to patented lubrication depots
– ested in accordance with EN 13126 – 8 2006–02 and EN 1191 2000 – 08
and certified according to 328
– Handles are available in different RAL colours
– With burglar-inhibiting anti-jemmy device in the tilt striker as standard
– Sash weights from 80 kg up to 150 kg thanks to load transfer component
– Long-term relieving of the pivot rest is ensured
– No jigs necessary for installation
– urn Only ilt urn sash
– Sash rebate width 330 – 1400 mm
– Sash rebate height 280 – 2600 mm
– Sash weight up to max. 150 kg
– Security levels acc. to IN EN 1627 1630
– Brands:
– Roto NT Designo or equivalent
* The application ranges are to be adhered according to the application diagrams
18 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
– Central locking system for one-hand-operation completely concealed in the
sash-rebate
– Profiled faceplate
– Effortless operation with low abrasion due to guided adjustable locking
cams
– Easy adjustment of the locking cams with standard tools
E cam gasket compression ad ustable eccentric cam and or
cam gasket compression ad ustable eccentric security cam and or
cam height and gasket compression ad ustable eccentric security cam
– Strong interlocking Clip it connection without loss of cam travel
– High uality Roto Sil Nano surface finish (matt silvery) for maximum corro-
sion resistance ( IN EN 1670 8 Class 5) using Nano particles (free from
Chromium I compounds)
– Rebate hinge with gasket-compression and clearance adjustment com-
pletely concealed in the sash rebate
– 10-year warranty on the operativeness of the hardware
– Low-maintenance
– ested in accordance with EN 13126 8 2006 02 and EN 1191 2000 08 and
certified according to 328
– Handles are available in different RAL colours
– Tilt-Only sash
– Sash rebate width 450 – 1400 mm
– Sash rebate height 370 – 1200 mm
– Sash weight up to max. 80 kg
– Handle height fixed, centred variable
– Security levels acc. to IN EN 1627–1630
– Brands:
Roto NT Designo or equivalent
* The application ranges are to be adhered according to the application diagrams.
Information on the productGeneral hardware characteristicsRoto NT Designo – Tilt-Only hardware for windows and balcony doors
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 19
Information on the productIntroduction
The surface-finish Roto Sil Nano surface-finish for ele-
gant matt silvery aesthetics. Unmis-
takable consistent silver look.
Optimal protection by means of gal-
vanising, chromating, and additional
sealing.
Increased corrosion protection.
The NT security concept The basic version of Roto NT is al-
ready equipped with basic security
on the bottom horizontal sash-plane.
Highest burglary inhibition results
are achieved with exemplary hard-
ware combinations for security win-
dows in accordance with
IN EN 1627–1630. his standard
includes an overall test of all individ-
ual window components.
Locking cam EGasket-compression adjustable cam
Locking cam PGasket-compression adjustable security mushroom cam
Locking cam VHeight and gasket-compression adjust-able security mush-room cam
The NT striker conceptAll strikers in the Roto NT hardware
system have identical screwing
axes.
This concept renders prefitting the
sash with security cams possible,
and a later frame retrofitting with se-
curity strikers ( inc or steel). ll lock-
ing cam versions are combinable
with all strikers.
Three locking cam versions The Roto NT hardware system offers
3 different locking cam versions that
differ in application and adjusting
capabilities.
The detailed adjusting dimensions
can be found in these installation
instructions.
20 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Information on the productFrame clearance
H
B
A
X
Axis dimension A Overlap height H Overlap width B Frame clearance (O 90 ) X
13 16 18 5.2
13 20 18 7.6
13 24 18 10.6
13 16 20 4.9
13 20 20 7.2
13 24 20 9.9
13 16 22 4.7
13 20 22 6.8
13 24 22 9.3
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 21
Information on the productDimensional data for hardware
Hardware axis
18/20/22
12
24/3
0
13
Profile dimensionsSystem Euro rebate 12 18(20 22) 13
Rebate depth 24/30
Clearance, bottom hori ontal 11.5 – 14 mm
Clearance on the sides 10 – 14 mm
Clearance, top 11 – 14 mm
NOTE!The pivot rest of Designo is preset in the factory
to 12.5 mm clearance
9.4±0.2
2.2±0.2
16.2
+0.
2-0
.1
12.3
+0.
2-0
.1
13
18/20/22
Hardware axis
Hardware groove
Sash dimensions
22 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Information on the productApplication diagramurn Only ilt urn hardware for rectangular windows 80 kg without load transfer device
Application diagramHinge side NT Designo
urn Only ilt urn hardware for rectangular windows 80 kg without
load transfer device
Limitation of sash formats depending on the glass thickness
Application rangeSash rebate width SRW ...........................330 – 1400 mm
Sash rebate height SRH ...........................280 – 2600 mm
Sash weight S.kg ............................................ max. 80 kg
The information in the application diagram refers
to the glass weight in kg m2.
1 mm m2 glass thickness 2.5 kg
= Impermissible application range
= Additional scissor stay required
2000
1000
2500
1500
500
1000500
50 k
g/m
2
40 k
g/m
2
30 k
g/m
2
20 k
g/m
2
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 23
Information on the productApplication diagramurn Only ilt urn hardware for rectangular windows 100 kg without load transfer device
Application diagramHinge side NT Designo
urn Only ilt urn hardware for rectangular windows 100 kg without
load transfer device
Limitation of sash formats depending on the glass thickness
Application rangeSash rebate width SRW ...........................600 – 1400 mm
Sash rebate height SRH ...........................280 – 2600 mm
Sash weight S.kg .......................................... max. 100 kg
The information in the application diagram refers
to the glass weight in kg m2.
1 mm m2 glass thickness 2.5 kg
= Impermissible application range
= Additional scissor stay required
2000
1000
2500
1500
500
1000500
50 k
g/m
2
40 k
g/m
2
30 k
g/m
2
24 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Information on the productApplication diagramilt urn hardware rectangular windows with load transfer device from 80 – 150 kg
Application diagramHinge side NT Designo
ilt urn hardware rectangular windows with load transfer device from
80 – 150 kg
Limitation of sash formats depending on the glass thickness
Application rangeSash rebate width SRW ...........................800 – 1400 mm
Sash rebate height SRH .........................1000 – 2600 mm
Sash weight S.kg .................................. max. 80 – 150 kg
The information in the application diagram refers
to the glass weight in kg m2.
1 mm m2 glass thickness 2.5 kg
= Impermissible application range
= Additional scissor stay required
If the sash weight is 130 kg, set the stay arm s tilt restrictor to
80 mm.
2000
1000
1000
2500
1500
500
50060
kg
/m2
80 k
g/m
2
50 k
g/m
2
40 k
g/m
2
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 25
1000
1000
500550
500621
SRW in mm
SR
H in
mm
Information on the productApplication diagramTilt-Only hardware for rectangular windows
Application diagramHinge side NT Designo
Tilt-Only hardware for rectangular windows
Limitation of sash formats depending on the glass thickness
Application rangeSash rebate width SRW .............................450 – 1400 mm
Sash rebate height SRH .............................370 – 1200 mm
Sash weight S.kg .............................................max. 80 kg
The information in the application diagram refers
to the glass weight in kg m2.
1 mm/m2 glass thickness = 2.5 kg
= Impermissible application range
= 2 tilt-stays laterally
= 1 tilt-stay on top
= 2 tilt-stays laterally or on top
= 2 tilt-stays on top
26 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 27
Hardware overviewExplanation on the hardware overview chapter
The hardware overviews on the following pages are recommendations of
Roto Frank AG.
The hardware overview chapter shows on the left page the single hardware
components in the hardware overview and on the right page the respective
parts list.
Position numbers in surrounding circles allow the allocation between hard-
ware overview and parts list.
28 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Hardware overviewTilt&Turn hardware – Basic securityHardware overview
6)
3)
On SRH < 900 mm (on windows without overlap gasket on SRH < 600 mm) the tilt depth must be limited to 80 mm
(see page 69).
1
2
3
4
5
6
21
21
21
21
21
8
911
14
22
23
20
15
19
18
10
13
7
24
17
12
16
25
6
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 29
Hardware overview Tilt&Turn hardware – Basic securityParts list
Application rangeSash rebate width SRW .................... 3301) – 14003) mm
Sash rebate width with load transfer ...... 525 – 14003) mm
Sash rebate height SRH ......................2802)6) – 26004) mm
Sash rebate height with load transfer ... 1000 – 26004) mm
Sash weight without load transfer ........... max. 100 kg
Sash weight with load transfer ................. max. 150 kg
1 T&T espagnolette, fixed handle height, backset 15 mm9)
SRH / mm Handle height / mm Espagnolette length Material no.
280 – 360 5),6),7),8) 120 370 284314
361 – 480 5),7) 120 370 284314
481 – 600 170 490 259830
601 – 800 263 690 259831
801 – 1000 413 890 259834
1001 – 1200 513 1090 1 E 259838
1201 – 1400 563 1290 1 E 259840
1401 – 1600 563 1490 1 E 259842
1601 – 1800 563 1690 2 E 259846
1601 – 1800 1000 1690 2 E 259847
1801 – 2000 1000 1890 2 E 259849
2001 – 2200 1000 2090 2 E 259851
2201 – 2400 1000 2290 2 E 259854
2401 – 2600 4) 1000 2290 3 E 259855
2 T&T espagnolette, centred/variable handle height, backset 15 mm9)
SRH / mm Handle height / mm Espagnolette length Material no.
310 – 450 6),7),8) 155 – 225 430 259717
451 – 620 7) 225 – 310 400 259718
621 – 800 311 – 400 580 1 E 259719
801 – 1200 401 – 600 980 1 E 259720
1201 – 1600 601 – 800 1380 2 E 259721
1601 – 2000 801 – 1000 1780 2 E 259762
2001 – 2400 1001 – 1200 2180 4 E 259763
2401 – 2600 4) 1001 – 1200 2180 4 E 259763
3 Centre lock (from SRH 2401 mm)SRH / mm Size Material no.
2401 – 2600 200 CON 308267
4 Bullet catch cam 256020
5 Lifting mishandling device, sash component 260538
6 Corner drive not dep. E 260275
Corner drive P 260277
7 Corner drive, T&T P 260290
8 Special corner drive not dep. E 260280
(SRH < 360 or SRW < 430)
Special corner drive P 260282
(SRH < 360 or SRW < 430)
9 Stay guideSRW / mm Description Length Material no.
330 – 430 8) 250 490 385393
431 – 600 250 490 385393
601 – 800 350 690 385394
801 – 1000 500 890 1 E 385415
1001 – 1200 500 1090 1 E 385416
1201 – 1400 3) 500 1090 1 E 385416
10 Stay arm p. 56
11 Stay corner drive 6) P 260286
12 Corner hinge 634705
13 Pivot rest p. 56
14 Multipart centre lock, verticalSRH / mm w/o load transfer (≤ 80 kg)
SRH / mm with load transfer (≥ 80 kg)
Size Material no.
1101 – 1150 400 1 E 255280
1101 – 1800 1151 – 1800 600 1 E 255281
1801 – 2400 1801 – 2400 600 CON 1 E 255282
600 1 E 255281
2401 – 2600 2401 – 2600 600 CON 1 E 255282
600 CON 1 E 255282
400 1 E 255280
15 Multipart centre lock, horizontalSRW / mm Size Material no.
1101 – 1400 600 1 E 255281
16 Additional scissor stay (from SRW 1201) 255237
17 Turn-restrictor, sash component 485591
(possible from SRW 525, mandatory from SRW 1000 mm and when using load transfer device)
18 Load transfer device, sash component 567972
19 Load transfer device, frame component 565254
Profile-related frame components: p. 54
20 Tilt striker
21 Striker
22 Bullet catch
23 Lifting mishandling device, frame component
24 Turn-restrictor, frame component
(possible from SRW 525, mandatory from SRW 1000 mm and when using load transfer device)
25 Night-vent, as an option
1) SRW 330 – 430 mm from SRH 361 mm2) SRH 280 – 361 mm from SRW 431 mm3) Use an additional scissor stay from SRW 1201 mm
4) From SRH 2401 mm CL 200 CON 3
5) With integrated corner drive6) SRH 280 – 330 mm: Shorten stay corner drive with completely extended connecting rod7) Not possible in combination with a lifting mishandling device8) With special corner drive9) Please refer to CTL_6 for further backsets
NOTE!Installation instructions for frame components
see page 74 – 75.
The actual scope of delivery depends on the ordered hardware configuration
(height and width of the window).
28 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Hardware overviewTilt&Turn hardware – Basic securityHardware overview
6)
3)
On SRH < 900 mm (on windows without overlap gasket on SRH < 600 mm) the tilt depth must be limited to 80 mm
(see page 69).
1
2
3
4
5
6
21
21
21
21
21
8
911
14
22
23
20
15
19
18
10
13
7
24
17
12
16
25
6
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 29
Hardware overview Tilt&Turn hardware – Basic securityParts list
Application rangeSash rebate width SRW ....................... 3301) – 14003) mm
Sash rebate width with load transfer ...... 525 – 14003) mm
Sash rebate height SRH ......................2802)6) – 26004) mm
Sash rebate height with load transfer ... 1000 – 26004) mm
Sash weight without load transfer ........... max. 100 kg
Sash weight with load transfer ................. max. 150 kg
1 T&T espagnolette, fixed handle height, backset 15 mm9)
SRH / mm Handle height / mm Espagnolette length Material no.
280 – 360 5),6),7),8) 120 370 284314
361 – 480 5),7) 120 370 284314
481 – 600 170 490 259830
601 – 800 263 690 259831
801 – 1000 413 890 259834
1001 – 1200 513 1090 1 E 259838
1201 – 1400 563 1290 1 E 259840
1401 – 1600 563 1490 1 E 259842
1601 – 1800 563 1690 2 E 259846
1601 – 1800 1000 1690 2 E 259847
1801 – 2000 1000 1890 2 E 259849
2001 – 2200 1000 2090 2 E 259851
2201 – 2400 1000 2290 2 E 259854
2401 – 2600 4) 1000 2290 3 E 259855
2 backset 15 mm9)
SRH / mm Handle height / mm Espagnolette length Material no.
310 – 450 6),7),8) 155 – 225 430 259717
451 – 620 7) 225 – 310 400 259718
621 – 800 311 – 400 580 1 E 259719
801 – 1200 401 – 600 980 1 E 259720
1201 – 1600 601 – 800 1380 2 E 259721
1601 – 2000 801 – 1000 1780 2 E 259762
2001 – 2400 1001 – 1200 2180 4 E 259763
2401 – 2600 4) 1001 – 1200 2180 4 E 259763
3 Centre lock (from SRH 2401 mm)SRH / mm Size Material no.
2401 – 2600 200 CON 308267
4 Bullet catch cam 256020
5 Lifting mishandling device, sash component 260538
6 Corner drive not dep. E 260275
Corner drive P 260277
7 Corner drive, T&T P 260290
8 Special corner drive not dep. E 260280
(SRH < 360 or SRW < 430)
Special corner drive P 260282
(SRH < 360 or SRW < 430)
9 Stay guideSRW / mm Description Length Material no.
330 – 430 8) 250 490 385393
431 – 600 250 490 385393
601 – 800 350 690 385394
801 – 1000 500 890 1 E 385415
1001 – 1200 500 1090 1 E 385416
1201 – 1400 3) 500 1090 1 E 385416
10 Stay arm p. 56
11 Stay corner drive P 260286
12 Corner hinge 634705
13 Pivot rest p. 56
14 Multipart centre lock, verticalSRH / mm w/o load transfer (≤ 80 kg)
SRH / mm with load transfer (≥ 80 kg)
Size Material no.
1101 – 1150 400 1 E 255280
1101 – 1800 1151 – 1800 600 1 E 255281
1801 – 2400 1801 – 2400 600 CON 1 E 255282
600 1 E 255281
2401 – 2600 2401 – 2600 600 CON 1 E 255282
600 CON 1 E 255282
400 1 E 255280
15 Multipart centre lock, horizontalSRW / mm Size Material no.
1101 – 1400 600 1 E 255281
16 Additional scissor stay (from SRW 1201) 255237
17 Turn-restrictor, sash component 485591
(possible from SRW 525, mandatory from SRW 1000 mm and when using load transfer device)
18 Load transfer device, sash component 567972
19 Load transfer device, frame component 565254
p. 54
20 Tilt striker
21 Striker
22 Bullet catch
23 Lifting mishandling device, frame component
24 Turn-restrictor, frame component
(possible from SRW 525, mandatory from SRW 1000 mm and when using load transfer device)
25 Night-vent, as an option
1) SRW 330 – 430 mm from SRH 361 mm2) SRH 280 – 361 mm from SRW 431 mm3) Use an additional scissor stay from SRW 1201 mm
4) From SRH 2401 mm CL 200 CON 3
5) With integrated corner drive6) SRH 280 – 330 mm: Shorten stay corner drive with completely extended connecting rod7) Not possible in combination with a lifting mishandling device8) With special corner drive9) Please refer to CTL_6 for further backsets
NOTE!Installation instructions for frame components
see page 74 – 75.
30 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
4)
Hardware overview
Hardware overview
1)
On SRH < 900 mm (on windows without overlap gasket on SRH < 600 mm) the tilt depth must be limited to 80 mm
(see page 69).
118
5
8
2
23
23
10
9
6
7
11
14
26
24
25
15
22
22
4
6
132321
17
12
16
20
19
3
27
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 31
Application rangeSash rebate width SRW ......................... 450 – 14001) mm
Sash rebate width with load transfer ...... 650 – 14001) mm
Sash rebate height SRH ....................... 2804) – 26002) mm
Sash rebate height with load transfer ... 1000 – 26002) mm
Hardware overview
Parts list
1 T&T espagnolette, fixed handle height, backset 15 mm7)
SRH / mm Handle height / mm Espagnolette length Material no.
280 – 360 3),4),5),6) 120 370 284314
361 – 480 3),6) 120 370 284314
481 – 600 170 490 259830
601 – 800 263 690 259831
801 – 1000 413 890 259834
1001 – 1200 513 1090 1 E 259838
1201 – 1400 563 1290 1 E 259840
1401 – 1600 563 1490 1 E 259842
1601 – 1800 563 1690 2 E 259846
1601 – 1800 1000 1690 2 E 259847
1801 – 2000 1000 1890 2 E 259849
2001 – 2200 1000 2090 2 E 259851
2201 – 2400 1000 2290 2 E 259854
2401 – 2600 2) 1000 2290 3 E 259855
2 backset 15 mm7)
SRH / mm Handle height / mm Espagnolette length Material no.
310 – 450 4),5),6) 155 – 225 430 259717
451 – 620 5) 225 – 310 400 259718
621 – 800 311 – 400 580 1 E 259719
801 – 1200 401 – 600 980 1 E 259720
1201 – 1600 601 – 800 1380 2 E 259721
1601 – 2000 801 – 1000 1780 2 E 259762
2001 – 2400 1001 – 1200 2180 4 E 259763
2401 – 2600 2) 1001 – 1200 2180 4 E 259763
3 Centre lock (from SRH 2401 mm)SRH / mm Size Material no.
2401 – 2600 200 CON 308267
4 Bullet catch cam 256020
5 Lifting mishandling device, sash component 260538
6 Corner drive P 260277
7 Corner drive, T&T P 260290
8 Special corner drive (SRH < 360) P 260282
9 Stay guideSRW / mm Description Length Material no.
450 – 600 250 490 385393
601 – 800 350 690 385394
801 – 1000 500 890 1 E 385415
1001 – 1200 500 1090 1 E 385416
1201 – 1400 1) 500 1090 1 E 385416
10 Stay arm p. 56
11 Stay corner drive P 260286
12 Corner hinge 634705
13 Pivot rest p. 56
14 Multipart centre lock, verticalSRH / mm w/o load transfer (≤ 80 kg)
SRH / mm with load transfer (≥ 80 kg)
Size Material no.
1101 – 1150 400 1 E 255280
1101 – 1800 1151 – 1800 600 1 E 255281
1801 – 2400 1801 – 2400 600 CON 1 E 255282
600 1 E 255281
2401 – 2600 2401 – 2600 600 CON 1 E 255282
600 CON 1 E 255282
400 1 E 255284
15 Multipart centre lock, horizontalSRW / mm w/o turn-restrictor
SRW / mm with turn-restrictor
Size Material no.
450 – 650 650 – 850 200 1 P 255284
651 – 850 851 – 1050 400 1 P 255285
851 – 1000 1051 – 1250 600 1 P 255286
1251 – 1400 600 CON 1 E 255282
200 1 P 255284
16 Additional scissor stay (from SRW 1201) 255237
17 Turn-restrictor, sash component 485591
(possible from SRW 650, mandatory from SRW 1000 mm and when using load transfer device)
18 Drilling protection 627343
19 Load transfer device, sash component 567972
20 Load transfer device, frame component 565254
p. 54
21 Tilt striker
22 Striker
23 Security striker
24 Bullet catch
25 Lifting mishandling device, frame component
26 Turn-restrictor, frame component
(possible from SRW 650, mandatory from SRW 1000 mm and when using load transfer device)
27 Night-vent, as an option
1) Use an additional scissor stay from SRW 1201 mm
2) From SRH 2401 mm CL 200 CON 3
3) With integrated corner drive4) SRH 280 – 330 mm: Shorten stay corner drive with completely extended connecting rod5) Not possible in combination with a lifting mishandling device6) With special corner drive7) Please refer to CTL_6 for further backsets
Sash weight without load transfer ........... max. 100 kg
Sash weight with load transfer ................. max. 150 kg
NOTE!Installation instructions for frame components
see page 76 – 77.
32 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Hardware overview
Hardware overview
On SRH < 900 mm (on windows without overlap gasket on SRH < 600 mm) the tilt depth must be limited to 80 mm
(see page 69).
1)
1)
1
173
21
21
9
8
6
10
13
24
22
23
14
21
21
21
21
4
5
122120
11
15
1619
18
25
2
5
7
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 33
Application rangeSash rebate width SRW ..........................450 – 14001) mm
Sash rebate width with load transfer ...... 650 – 14001) mm
Sash rebate height SRH ...........................490 – 2400 mm
Sash rebate height with load transfer ....1000 – 2400 mm
Sash weight without load transfer ........... max. 100 kg
Sash weight with load transfer ................. max. 150 kg
Hardware overview
Parts list
1 T&T espagnolette, fixed handle height, backset 15 mm2)
SRH / mm Handle height / mm Espagnolette length Material no.
490 – 600 170 490 259830
601 – 800 263 690 1 259832
801 – 1000 413 890 2 259835
1001 – 1200 513 1090 2 259837
1201 – 1400 563 1290 2 259839
1201 – 1600 563 1490 3 259841
1601 – 1800 563 1690 3 259844
1601 – 1800 1000 1690 3 259845
1801 – 2000 1000 1890 3 259848
2001 – 2200 1000 2090 4 259850
2201 – 2400 1000 2290 4 259853
2 backset 15 mmSRH / mm Handle height / mm Espagnolette length Material no.
490 – 620 245 – 310 400 2597183),4)
621 – 800 311 – 400 580 1 355743
801 – 1200 401 – 600 980 1 355744
1201 – 1600 601 – 800 1380 2 355745
1601 – 2000 801 – 1000 1780 2 355746
2001 – 2400 1001 – 1200 2180 4 355747
3 Bullet catch cam 256020
4 Lifting mishandling device, sash component 260538
5 Corner drive 260272
6 Corner drive, T&T 260288
7 Corner drive RC3 260274
8 Security stay guideSRW / mm Description Length Material no.
450 – 600 250 490 385393
601 – 800 350 690 385394
801 – 1000 500 890 1 450373
1001 – 1200 500 1090 1 450374
1201 – 1400 1) 500 1090 1 450374
9 Stay arm p. 56
10 Stay corner drive 260284
11 Corner hinge 634705
12 Pivot rest p. 56
13 Multipart centre lock, verticalSRH / mm w/o load transfer (≤ 80 kg)
SRH / mm with load transfer (≥ 80 kg)
Size Material no.
490 – 650 200 1 296853
651 – 850 1000 – 1150 400 1 296854
851 – 1050 1151 – 1350 600 1 2968555),8)
1051 – 1250 1351 – 1550 600 CON 1 337711
200 1 296853
1251 – 1450 1551 – 1750 600 CON 1 337711
400 1 296854
1451 – 1650 1751 – 1950 600 CON 1 337711
600 1 2968556),9)
13 Multipart centre lock, verticalSRH / mm w/o load transfer (≤ 80 kg)
SRH / mm with load transfer (≥ 80 kg)
Size Material no.
1651 – 1850 1951 – 2150 600 CON 1 337711
600 CON 1 337711
200 1 296853
1851 – 2050 2151 – 2350 600 CON 1 337711
600 CON 1 337711
400 1 296854
2051 – 2250 2351 – 2400 600 CON 1 337711
600 CON 1 337711
600 1 2968557),10)
2251 – 2400 600 CON 1 337711
600 CON 1 337711
600 CON 1 337711
200 1 296853
14 Multipart centre lock, horizontalSRW / mm w/o turn restrictor
SRW / mm with turn-restrictor
Size Material no.
450 – 650 650 – 850 200 1 296853
651 – 850 851 – 1050 400 1 296854
851 – 1000 1051 – 1250 600 1 296855
1251 – 1400 600 CON 1 337711
200 1 296853
15 Additional scissor stay (from SRW 1201) 255237
16 Turn-restrictor, sash component 485591
(possible from SRW 650, mandatory from SRW 1000 mm and when using load transfer device)
17 Drilling protection 627343
18 Load transfer device, sash component 567972
19 Load transfer device, frame component 565254
p. 54
20 Tilt striker
21 Security striker
22 Bullet catch
23 Lifting mishandling device, frame component
24 Turn-restrictor, frame component
(possible from SRW 650, mandatory from SRW 1000 mm and when using load transfer device)
25 Night-vent, as an option
1) Use an additional scissor stay from SRW 1201 mm2) Please refer to CTL_6 for further backsets3) Not possible in combination with a lifting mishandling device
4) With corner drive RC3 7 bottom) Cut CL 1 mm up to SRW 861 mm
6) Cut CL 1 mm up to SRW 1461 mm7) Cut CL 1 mm up to SRW 2061 mm8) When using load transfer device cut CL 1 mm on SRH 11 1 mm9) When using load transfer device cut CL 1 mm on SRH 17 1 mm10) When using load transfer device cut CL 1 mm on SRH 23 1 mm
NOTE!Installation instructions for frame components
see page 78.
34 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
On SRH < 900 mm (on windows without overlap gasket on SRH < 600 mm) the tilt depth must be limited to 80 mm
(see page 69).
4)4)
Hardware overviewTilt-First hardware – Basic securityHardware overview
1)
1
2
4
21
21
10
9
7
11
14
24
22
23
15
21
6
21
5
6
3 8
1321
17
20
12
16
19
18
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 35
Application rangeSash rebate width SRW ......................... 330 – 14001) mm
Sash rebate width with load transfer ...... 525 – 14001) mm
Sash rebate height SRH ...........................280 – 2600 mm
Sash rebate height with load transfer ....1000 – 2600 mm
Sash weight without load transfer ........... max. 100 kg
Sash weight with load transfer ................. max. 150 kg
Hardware overviewTilt-First hardware – Basic securityParts list
10 Stay arm Tilt-First p. 56
16 Additional scissor stay Tilt-First (from SRW 1201) 292022
p. 54
20 Tilt striker Tilt-First
1) Use an additional scissor stay from SRW 1201 mm
NOTE!Installation instructions for frame components
see page 74 – 75.
NOTE!For hardware components shown greyed out,
please refer to the Basic security chapter
ilt urn hardware, page 29.
36 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
3)
3)
Hardware overviewTurn-Only hardware – Basic securityHardware overview
1
18
4
8
2
18
19
1013
18
6
7
9
14
22
20
21
5
13
3
6
121817
16
15
11
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 37
Application rangeSash rebate width SRW ......................... 3703) – 1400 mm
Sash rebate height SRH ..........................280 – 26001) mm
Sash weight ................................................... max. 100 kg
Hardware overviewTurn-Only hardware – Basic securityParts list
1 T&T espagnolette, fixed handle height, backset 15 mm6)
SRH / mm Handle height / mm Espagnolette length Material no.
280 – 360 2),4),5) 120 370 284314
361 – 480 2),4) 120 370 284314
481 – 600 170 490 259830
601 – 800 263 690 259831
801 – 1000 413 890 259834
1001 – 1200 513 1090 1 E 259838
1201 – 1400 563 1290 1 E 259840
1401 – 1600 563 1490 2 E 259842
1601 – 1800 563 1690 2 E 259846
1601 – 1800 1000 1690 2 E 259847
1801 – 2000 1000 1890 2 E 259849
2001 – 2200 1000 2090 2 E 259851
2201 – 2400 1000 2290 2 E 259854
2401 – 2600 1) 1000 2290 3 E 259855
2 backset 15 mm6)
SRH / mm Handle height / mm Espagnolette length Material no.
310 – 450 4),5) 155 – 225 430 259717
451 – 620 4) 225 – 310 400 259718
621 – 800 311 – 400 580 1 E 259719
801 – 1200 401 – 600 980 1 E 259720
1201 – 1600 601 – 800 1380 2 E 259721
1601 – 2000 801 – 1000 1780 2 E 259762
2001 – 2400 1001 – 1200 2180 4 E 259763
2401 – 2600 1) 1001 – 1200 2180 4 E 259763
3 Centre lock (from SRH 2401 mm)SRH / mm Size Material no.
2401 – 2600 200 CON 308267
4 Bullet catch cam 256020
5 Lifting mishandling device, sash component 260538
6 Corner drive not dep. E 260275
Corner drive P 260277
7 Corner drive, T&T P 260290
8 Special corner drive E 260280
(SRH < 360 450)
Special corner drive P 260282
(SRH < 360 450)
9 Sash-component for rebate hinge 477255
10 Rebate-hinge arm p. 56
11 Corner hinge 634705
12 Pivot rest p. 56
13 Multipart centre lock, horizontalSRW / mm Size Material no.
1101 – 1400 600 1 E 255281
14 Centre-closer, concealed, sash component 450984
15 Turn-restrictor, sash component 485591
(possible from SRW 525, mandatory from SRW 1000 mm and when using load transfer device)
16 90° travel restrictor 264603
p. 54
17 Security striker
18 Striker
19 Centre-closer, concealed, frame component7)
20 Bullet catch
21 Lifting mishandling device, frame component
22 Turn-restrictor, frame component
(possible from SRW 525, mandatory from SRW 1000 mm)
1) From SRH 2401 mm CL 200 CON 3
2) With integrated corner drive3) SRW 370 – 410 mm: Shorten corner drive on top 4) Not possible in combination with a lifting mishandling device5) With special corner drive6) Please refer to CTL_6 for further backsets7) Put pressure-resistant packers between glass and frame in the area of the centre-closers
NOTE!Installation instructions for frame components
see page 80 – 81.
38 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
1) 1)
Hardware overviewTilt-Only hardware – Basic securityHardware overview
7 7
5
9
2
9 9 9
8
9
10
1
7
2
5
4 4
6
3 3
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 39
Application rangeSash rebate width SRW ......................... 4502) – 1400 mm
Sash rebate height SRH .......................3701),3) – 1200 mm
Sash weight ..................................................... max. 80 kg
Hardware overviewTilt-Only hardware – Basic securityParts list
1 backset 15 mm4)
SRW / mm Espagnolette length Material no.
451 – 620 400 259718
621 – 800 580 1 E 259719
801 – 1200 980 1 E 259720
1201 – 1400 1380 2 E 259721
2 Corner drive not dep. E 260275
Corner drive P 260277
3 Sash-component for rebate hinge 640563
4 Rebate-hinge arm p. 56
5 Multipart centre lock, verticalSRH / mm Size Material no.
801 – 1200 400 1 E 255280
6 Centre-closer, concealed, sash component 450984
7 Tilt-stay set for faceplate mounting 482823
Screw for mounting on corner drive 567995
8 264603
p. 54
9 Striker
10 Centre-closer, concealed, frame component
1) SRH 370 – 410 mm: Shorten corner drive2) SRW 4 0 – 620 mm only from SRH 00 mm3) SRH 370 – 00 mm only from SRW 621 mm4) Please refer to CTL_6 for further backsets
NOTE!Installation instructions for frame components
see page 82.
NOTE!Installation of tilt-stay, cf. IMO_111
( 576).
40 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
On SRH < 900 mm (on windows without overlap gasket on SRH < 600 mm) the tilt depth must be limited to 80 mm
(see page 69).
w/o centre post
Hardware overview
Hardware overview
NOTE!Please refer to page 43 for possible combina-
tions of corner drives in the case of low and
narrow sashes.
INSTALLATION ADVICEHinge in the passive sash with lever-operated
espagnolette in open position.
5)
1)
26
15
15
21
33 33
2727
29
3029 30
33
2
28
1717
19
19a23
18
18a
30 31 30
30
30
26
32 1425
13 13
15
5
1
4
6 6
88
77
6 6
20
1212
1122
1024
9
16
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 41
Application rangeSash rebate width SRW ......................... 370 – 14001) mm
Sash rebate width with load transfer ..... 525 – 14001) mm
Sash rebate height SRH ......................... 370 – 26002) mm
Sash rebate height with load transfer ... 1000 – 26002) mm
Sash weight without load transfer ........... max. 100 kg
Sash weight with load transfer ................. max. 150 kg
1 T&T espagnolette, fixed handle height, backset 15 mm7)
SRH / mm Handle height / mm Handle length / mm Material no.
430 – 480 3),4) 120 370 284314
481 – 600 170 490 259830
601 – 800 263 690 259831
801 – 1000 413 890 259834
1001 – 1200 513 1090 1 E 259838
1201 – 1400 563 1290 1 E 259840
1401 – 1600 563 1490 1 E 259842
1601 – 1800 563 1690 2 E 259846
1601 – 1800 1000 1690 2 E 259847
1801 – 2000 1000 1890 2 E 259849
2001 – 2200 1000 2090 2 E 259852
2201 – 2400 1000 2290 2 E 259854
2401 – 2600 2) 1000 2290 3 E 259855
2 backset 15 mm7)
SRH / mm Handle height / mm Handle length / mm Material no.
370 – 450 4) 155 – 225 430 259717
451 – 620 4) 225 – 310 400 259718
621 – 800 311 – 400 580 1 E 259719
801 – 1200 401 – 600 980 1 E 259720
1201 – 1600 601 – 800 1380 2 E 259721
1601 – 2000 801 – 1000 1780 2 E 259762
2001 – 2400 1001 – 1200 2180 4 E 259763
2401 – 2600 2) 1001 – 1200 2180 4 E 259763
3 Centre lock (from SRH 2401 mm)SRH / mm Size Material no.
2401 – 2600 200 CON 308267
4 Bullet catch cam 256020
5 Lifting mishandling device, sash component 260538
6 Corner drive not dep. E 260275
Corner drive P 260277
7 Corner drive, T&T P 260290
8 Special corner drive E 260280
(SRW < 430 mm)
Special corner drive P 260282
(SRW < 430 mm)
9 Stay guideSRW / mm Description Length Material no.
370 – 430 250 490 385393
431 – 600 250 490 385393
601 – 800 350 690 385394
801 – 1000 500 890 1 E 385415
1001 – 1200 500 1090 1 E 385416
1201 – 1400 1) 500 1090 1 E 385416
4 Stay arm p. 56
11 Stay corner drive P 260286
12 Corner hinge 634705
13 Pivot rest p. 56
14 Multipart centre lock, verticalSRH / mm w/o load transfer (≤ 80 kg)
SRH / mm with load transfer (≥ 80 kg)
Size Material no.
1101 – 1150 400 1 E 255280
1101 – 1800 1151 – 1800 600 1 E 255281
1801 – 2400 1801 – 2400 600 CON 1 E 255282
600 1 E 255281
2401 – 2600 2401 – 2600 600 CON 1 E 255282
600 CON 1 E 255282
400 1 E 255280
15 Multipart centre lock, horizontalSRW / mm Size Material no.
1100 – 1400 600 1 E 255281
16 Additional scissor stay (from SRW 1201) 255237
17 Turn-restrictor, sash component 485591
(possible from SRW 525, mandatory from SRW 1000 mm and when using load transfer device)
Hardware overview
Parts list
42 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Hardware overview
Parts list
18 Lever-operated espagnolette, fixed lever-height6)
SRH / mm Lever position Length Material no.
430 – 500 195 490 233408
501 – 600
601 – 800 335 690 233409
801 – 1000 490 890 233410
1001 – 1200 335 1090 233411
1201 – 1400 335 1290 233412
1401 – 1600 335 1490 233413
1601 – 1800 335 1690 296145
1801 – 2000 640 1890 296074
2001 – 2200 640 2090 296075
2201 – 2400 640 2290 296076
2401 – 2600 12) 640 2290 296076
18a Lever-operated espagnolette Plus, fixed lever-height15)
SRH / mm Lever position Length / mm Material no.
431 – 500 8) 195 490 623365
501 – 600 9)
431 – 600 233 490 62336610)
601 – 800 195 690 62336811)
601 – 800 195 690 62336711)
601 – 800 335 690 623369
801 – 1000 490 890 623371
801 – 1000 195 890 62337011)
1001 – 1200 335 1090 623372
1201 – 1400 335 1290 623373
1401 – 1600 335 1490 623374
1601 – 1800 335 1690 623375
1801 – 2000 640 1890 623376
2001 – 2200 640 2090 623377
2201 – 2400 640 2290 623378
2401 – 2600 12) 640 2290 623378
19 6)
SRH / mm Lever position Length Material no.
370 – 520 225 – 300 400 233418
521 – 620 301 – 350 400 233418
621 – 650 393 – 407 680 233419
651 – 800 408 – 482 680 233419
801 – 1200 482 – 682 980 233420
1201 – 1600 448 – 648 1380 290912
1601 – 2000 680 – 880 1780 296146
2001 – 2400 880 – 1080 2180 296147
2401 – 2600 12) 1080 2180 296147
19a 15)
SRH / mm Lever position Length / mm Material no.
370 – 620 225 – 350 400 62337914)
621 – 800 393 – 482 680 623380
621 – 900 680 62338111)
801 – 1200 482 – 682 980 623382
901 – 1200 980 62338311)
1201 – 1600 448 – 658 1380 623384
1601 – 2000 680 – 890 1780 623385
2001 – 2400 880 – 1090 2180 623386
2401 – 2600 12) 1090 2180 623386
NOTE!Installation instructions for frame components
see page 83.
20 Bullet catch for lever-operated espagnolette 385031
21 Lifting mishandling device 257600
Stop for lever-operated espagnolette
22 Sash-component for rebate hinge 477255
23 Corner drive with security striker5) 313538
24 Rebate-hinge arm p. 56
25 Centre-closer, concealed, sash component 450984
26 Load transfer device, sash component 567972
27 Load transfer device, frame component 565254
28 Run-up block 350402
p. 54
29 Tilt striker
30 Striker
31 Security striker
32 Centre-closer, concealed, frame component12)
33 Turn-restrictor, frame component
(possible from SRW 525, mandatory from SRW 1000 mm and when using load transfer device)
1) Use an additional scissor stay from SRW 1201 mm 16
2) From SRH 2401 mm CL 200 CON 3
3) With integrated corner drive 1 4) Not possible in combination with a lifting mishandling device) SRW 370 – 400 mm: Shorten corner drive on top
6) When using the lever operated espagnolette on the right hand side turn the eccentric cam 1807) Please refer to CTL_6 for further backsets8) With special corner drive 79) With corner drive 510) No striker possible11) For T T espagnolette 8 mm backset12) From SRH 2401 mm: centre lock CL 200 CON 313) Put pressure-resistant packers between glass and frame in the area of the centre-closers
14) Without lifting mishandling device (stop for lever-operated espagnolette)1 ) Lifting mishandling device (stop for lever operated espagnolette) preassembled as standard
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 43
Hardware overview
Combination possibilities: corner drives for low and narrow sashes
Fixed handle height, for low sashes
Material no. Material no.
SRH 430 – 500 8 260280260282
6 260275 Top
7 260290 7 260290 Bot-tom
Centred handle height, for low sashes
Material no. Material no.
SRH 370 – 450 8 260280260282
8 260280260282
Top
8 260280260282
8 260280260282
Bot-tom
SRH 451 – 520 8 260280260282
6 260275 Top
8 260280260282
6 260275 Bot-tom
SRH 521 – 620 6 260275 6 260275 Top
6 260275 6 260275 Bot-tom
SRH 621 – 650 6 260280260282
6 260275 Top
8 260280260282
6 260275 Bot-tom
Centred handle height, for narrow sashes
Material no. Material no.
SRW 370 – 400 23 313538 8 260280260282
Top
6 260275 6 260275 Bot-tom
SRW 401 – 430 23 313538 8 260280260282
Top
6 260275 6 260275 Bot-tom
Fixed handle height, for narrow sashes
Material no. Material no.
SRW 370 – 400 23 313538 8 260280260282
Top
7 260290 7 260290 Bot-tom
SRW 401 – 430 23 313538 8 260280260282
Top
7 260290 7 260290 Bot-tom
44 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
On SRH < 900 mm (on windows without overlap gasket on SRH < 600 mm) the tilt depth must be limited to 80 mm
(see page 69).
Hardware overview
Hardware overview
w/o centre post
INSTALLATION ADVICEHinge in the passive sash with lever-operated
espagnolette in open position.
1)
25
25
15 15
22
31 31
2626
28
3030
30
2
27
23
1717
19
19a
18
18a
30 30 30
30
2929
30
1414
13 13
24
5
1
4
6 6
88
77
6 6
20
1212
1111
1010
9
163 3
21
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 45
Application rangeSash rebate width SRW ..........................450 – 14001) mm
Sash rebate width with load transfer ...... 650 – 14001) mm
Sash rebate height SRH ......................... 370 – 26002) mm
Sash rebate height with load transfer ... 1000 – 26002) mm
Sash weight without load transfer ........... max. 100 kg
Sash weight with load transfer ................. max. 150 kg
Hardware overview
Parts list
1 T&T espagnolette, fixed handle height, backset 15 mm7)
SRH / mm Handle height / mm Handle length / mm Material no.
430 – 480 3),4) 120 370 284314
481 – 600 170 490 259830
601 – 800 263 690 259831
801 – 1000 413 890 259834
1001 – 1200 513 1090 1 E 259838
1201 – 1400 563 1290 1 E 259840
1401 – 1600 563 1490 1 E 259842
1601 – 1800 563 1690 2 E 259846
1601 – 1800 1000 1690 2 E 259847
1801 – 2000 1000 1890 2 E 259849
2001 – 2200 1000 2090 2 E 259851
2201 – 2400 1000 2290 2 E 259854
2401 – 2600 2) 1000 2290 3 E 259855
2 backset 15 mm7)
SRH / mm Handle height / mm Handle length / mm Material no.
370 – 450 4) 155 – 225 430 259717
451 – 620 4) 225 – 310 400 259718
621 – 800 311 – 400 580 1 E 259719
801 – 1200 401 – 600 980 1 E 259720
1201 – 1600 601 – 800 1380 2 E 259721
1601 – 2000 801 – 1000 1780 2 E 259762
2001 – 2400 1001 – 1200 2180 4 E 259763
2401 – 2600 2) 1001 – 1200 2180 4 E 259763
3 Centre lock (from SRH 2401 mm)SRH / mm Size Material no.
2401 – 2600 200 CON 308267
4 Bullet catch cam 256020
5 Lifting mishandling device, sash component 260538
6 Corner drive P 260277
7 Corner drive, T&T P 260290
8 Special corner drive P 260282
(SRH < 480 mm) (not dep.)
9 Stay guideSRW / mm Description Length Material no.
450 – 600 250 490 385393
601 – 800 350 690 385394
801 – 1000 500 890 1 E 385415
1001 – 1200 500 1090 1 E 385416
1201 – 1400 1) 500 1090 1 E 385416
10 Stay arm p. 56
11 Stay corner drive (SRH 370 – 2600 mm) P 260286
12 Corner hinge 634705
13 Pivot rest p. 56
14 Multipart centre lock, verticalSRH / mm w/o load transfer (≤ 80 kg)
SRH / mm with load transfer (≥ 80 kg)
Size Material no.
1001 – 1150 400 1 E 255280
1101 – 1800 1151 – 1800 600 1 E 255281
1801 – 2400 1801 – 2400 600 CON 1 E 255282
600 1 E 255281
2401 – 2600 2401 – 2600 600 CON 1 E 255282
600 CON 1 E 255282
400 1 E 255280
15 Multipart centre lock, horizontalSRW / mm w/o turn-restrictor
SRW / mm with turn-restrictor
Size Material no.
450 – 650 650 – 850 200 1 P 255284
651 – 850 851 – 1050 400 1 P 255285
851 – 1000 1051 – 1250 600 1 P 255286
1251 – 1400 600 CON 1 E 255282
1251 – 1400 200 1 P 255284
16 Additional scissor stay (from SRW 1201) 255237
17 Turn-restrictor, sash component 485591
(possible from SRW 650, mandatory from SRW 1000 mm and when using load transfer device)
46 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
18 Lever-operated espagnolette, fixed lever-height6)
SRH / mm Lever position Length Material no.
430 – 500 5) 195 490 233408
501 – 600
601 – 800 335 690 233409
801 – 1000 490 890 233410
1001 – 1200 335 1090 233411
1201 – 1400 335 1290 233412
1401 – 1600 335 1490 233413
1601 – 1800 335 1690 296145
1801 – 2000 640 1890 296074
2001 – 2200 640 2090 296075
2201 – 2400 640 2290 296076
2401 – 2600 2) 640 2290 296076
18a Lever-operated espagnolette Plus, fixed lever-height12)
SRH / mm Lever position Length / mm Material no.
431 – 500 5) 195 490 623365
501 – 600 8)
431 – 600 233 490 6233669)
601 – 800 195 690 62336810)
601 – 800 195 690 62336710)
601 – 800 335 690 623369
801 – 1000 490 890 623371
801 – 1000 195 890 62337010)
1001 – 1200 335 1090 623372
1201 – 1400 335 1290 623373
1401 – 1600 335 1490 623374
1601 – 1800 335 1690 623375
1801 – 2000 640 1890 623376
2001 – 2200 640 2090 623377
2201 – 2400 640 2290 623378
2401 – 2600 2) 640 2290 623378
19 6)
SRH / mm Lever position Length Material no.
370 – 520 5) 225 – 300 400 2334182)
521 – 620 301 – 350 400 2334182)
621 – 650 5) 393 – 407 680 233419
651 – 800 408 – 482 680 233419
801 – 1200 482 – 682 980 233420
1201 – 1600 448 – 648 1380 290912
1601 – 2000 680 – 880 1780 296146
2001 – 2400 880 – 1080 2180 296147
2401 – 2600 2) 880 – 1080 2180 296147
19a 6)
SRH / mm Lever position Length / mm Material no.
370 – 620 225 – 350 400 6233799)
621 – 800 393 – 482 680 623380
621 – 900 680 62338110)
801 – 1200 482 – 682 980 623382
901 – 1200 980 62338310)
1201 – 1600 448 – 658 1380 623384
1601 – 2000 680 – 890 1780 623385
2001 – 2400 880 – 1090 2180 623386
2401 – 2600 2) 1090 2180 623386
Hardware overview
Parts list
NOTE!Installation instructions for frame components
see page 84.
20 Bullet catch for lever-operated espagnolette 385031
21 Drilling protection 627343
22 Lifting mishandling device 257600
Stop for lever-operated espagnolette
23 Turn-Only stay guideSRW / mm Description Length Material no.
450 – 510 250 490 482571
511 – 1400 11) 250 600 473381
24 Centre lock, connectable, horizontal, top, TU-ONSRW / mm Size Material no.
711 – 910 200 CON 308267
911 – 1110 400 CON 1 E 280346
1111 – 1310 600 CON 1 E 255282
1311 – 1400 600 CON 1 E 255282
200 CON 308267
25 Load transfer device, sash component 567972
26 Load transfer device, frame component 565254
27 Run-up block 350402
p. 54
28 Tilt striker
29 Striker
30 Security striker
31 Turn-restrictor, frame component
(possible from SRW 650, mandatory from SRW 1000 mm and when using load transfer device)
1) Use an additional scissor stay from SRW 1201 mm 16
2) From SRH 2401 mm CL 200 CON 3
3) With integrated corner drive4) Not possible in combination with a lifting mishandling device5) With special corner drive 7 6) When using the lever operated espagnolette on the right hand side turn the eccentric cam 1807) Please refer to CTL_6 for further backsets8) With corner drive 59) Without lifting mishandling device (stop for lever-operated espagnolette)10) For T T espagnolette 8 mm backset11) From SRW 711 mm: connectable centre lock 24
12) Lifting mishandling device (stop for lever operated espagnolette) preassembled as standard
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 47
48 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
On SRH < 900 mm (on windows without overlap gasket on SRH < 600 mm) the tilt depth must be limited to 80 mm
(see page 69).
Hardware overview
Hardware overview
w/o centre post
INSTALLATION ADVICEHinge in the passive sash with lever-operated
espagnolette in open position.
1)
2626
14
14
21
31 31
2727
29
3030
30
22
28
24
1616
19
1717a
30 30 30
30
3030
30
1313
12 12
25
20
1
3
4 4
55
23
1111
1010
99
8
15
64
2
1818a
7
4
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 49
Application rangeSash rebate width SRW ..........................450 – 14001) mm
Sash rebate width with load transfer ...... 650 – 14001) mm
Sash rebate height SRH ...........................490 – 2400 mm
Sash rebate height with load transfer ....1000 – 2400 mm
Sash weight without load transfer ........... max. 100 kg
Sash weight with load transfer ................. max. 150 kg
Hardware overview
Parts list
1 T&T espagnolette, fixed handle height, backset 15 mm3)
SRH / mm Handle height / mm Espagnolette length Material no.
490 – 900 170 490 259830
601 – 800 263 690 1 259832
801 – 1000 413 890 2 259835
1001 – 1200 513 1090 2 259837
1201 – 1400 563 1290 2 259839
1401 – 1600 563 1490 3 259841
1601 – 1800 563 1690 3 259844
1601 – 1800 1000 1690 3 259845
1801 – 2000 1000 1890 3 259848
2001 – 2200 1000 2090 4 259850
2201 – 2400 1000 2290 4 259853
2 backset 15 mmSRH / mm Handle height / mm Espagnolette length Material no.
490 – 620 245 – 310 400 2597189),10)
621 – 800 311 – 400 580 1 355743
801 – 1200 401 – 600 980 1 355744
1201 – 1600 601 – 800 1380 2 355745
1601 – 2000 801 – 1000 1780 2 355746
2001 – 2400 1001 – 1200 2180 4 355747
3 Bullet catch cam 256020
4 Corner drive 260272
5 Corner drive, T&T 260288
6 Corner drive RC3 2 260274
7 1 367227
8 Stay guideSRW / mm Description Length Material no.
450 – 600 250 490 385393
601 – 800 350 690 385394
801 – 1000 500 890 1 450373
1001 – 1200 500 1090 1 450374
1201 – 1400 1) 500 1090 1 450374
9 Stay arm p. 56
10 Stay corner drive (SRH 490 – 2400 mm) 260286
11 Corner hinge 634705
12 Pivot rest p. 56
13 Multipart centre lock, verticalSRH / mm w/o load transfer (≤ 80 kg)
SRH / mm with load transfer (≥ 80 kg)
Size Material no.
490 – 650 200 1 296853
651 – 850 1000 – 1150 400 1 296854
851 – 1050 1151 – 1350 600 1 29685512),15)
1051 – 1250 1351 – 1550 600 CON 1 337711
200 1 296853
1251 – 1450 1551 – 1750 600 CON 1 337711
400 1 296854
1451 – 1650 1751 – 1950 600 CON 1 337711
600 1 29685513),16)
1651 – 1850 1951 – 2150 600 CON 1 337711
600 CON 1 337711
200 1 296853
1851 – 2050 2151 – 2350 600 CON 1 337711
600 CON 1 337711
400 1 296854
2050 – 2250 2351 – 2400 600 CON 1 337711
600 CON 1 337711
600 1 29685514),17)
2251 – 2400 600 CON 1 337711
600 CON 1 337711
600 CON 1 337711
200 1 296853
14 Multipart centre lock, horizontalSRW / mm w/o turn restrictor
SRW / mm with turn-restrictor
Size Material no.
450 – 650 650 – 850 200 1 296853
651 – 850 851 – 1050 400 1 296854
851 – 1000 1051 – 1250 600 1 296855
1251 – 1400 600 CON 1 337711
200 1 296853
15 Additional scissor stay (from SRW 1201) 255237
16 Turn-restrictor, sash component 485591
(possible from SRW 650, mandatory from SRW 1000 mm and when using load transfer device)
50 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
17 Lever-operated espagnolette, fixed lever-height2)
SRH / mm Lever position Length Material no.
601 – 800 335 690 233409
801 – 1000 490 890 233410
1001 – 1200 335 1090 233411
1201 – 1400 335 1290 233412
1401 – 1600 335 1490 233413
1601 – 1800 335 1690 296145
1801 – 2000 640 1890 296074
2001 – 2200 640 2090 296075
2201 – 2400 640 2090 296076
17a Lever-operated espagnolette Plus, fixed lever-height4)
SRH / mm Lever position Length / mm Material no.
600 – 800 195 690 6233685),6)
600 – 800 195 690 6233676)
600 – 800 335 690 623369
801 – 1000 490 890 623371
801 – 1000 195 890 6233706)
1001 – 1200 335 1090 623372
1201 – 1400 335 1290 623373
1401 – 1600 335 1490 623374
1601 – 1800 335 1690 623375
1801 – 2000 640 1890 623376
2001 – 2200 640 2090 623377
2201 – 2400 640 2290 623378
18 2)
SRH / mm Lever position Length Material no.
520 – 650 301 – 350 400 23341811)
651 – 800 408 – 482 680 233419
801 – 1200 482 – 682 980 233420
1201 – 1600 448 – 648 1380 290912
1601 – 2000 680 – 880 1780 296146
2001 – 2400 880 – 1080 2180 296147
18a 4)
SRH / mm Lever position Length / mm Material no.
520 – 650 225 – 350 400 6233795)
651 – 800 393 – 482 680 623380
651 – 900 680 6233816)
801 – 1200 482 – 682 980 623382
901 – 1200 980 6233836)
1201 – 1600 448 – 658 1380 623384
1601 – 2000 680 – 890 1780 623385
2001 – 2400 880 – 1090 2180 623386
Hardware overview
Parts list
NOTE!Installation instructions for frame components
see page 85.
19 Bullet catch for lever-operated espagnolette 385031
20 Lifting mishandling device, sash component 260538
21 Lifting mishandling device 257600
Stop for lever-operated espagnolette
22 Drilling protection 627343
23 Retainer-clasp 314203
24 Turn-Only stay guideSRW / mm Description Length Material no.
450 – 510 250 490 482571
511 – 1400 8) 250 600 473381
25 Centre lock, connectable, horizontal, top, Turn-Only sashSRW / mm Size Material no.
711 – 910 200 CON 1 337708
911 – 1110 400 CON 1 337710
1111 – 1310 600 CON 1 337711
1311 – 1400 600 CON 1 337711
200 CON 1 337708
26 Load transfer device, sash component 567972
27 Load transfer device, frame component 565254
28 Run-up block 350402
p. 54
29 Tilt striker
30 Security striker
31 Turn-restrictor, frame component
(possible from SRW 650, mandatory from SRW 1000 mm and when using load transfer device)
1) Use an additional scissor stay from SRW 1201 mm2) When using the lever operated espagnolette on the right hand side turn the eccentric cam 1803) Please refer to CTL_6 for further backsets4) Lifting mishandling device (stop for lever operated espagnolette) preassembled as standard5) No striker possible6) For T T espagnolette 8 mm backset7) Not for lever-operated espagnolette Plus8) From SRW 711 mm: connectable centre lock 25
9) Not possible in combination with a lifting mishandling device
10) With corner drive RC3 6 bottom
11) With corner drive with welded-on striker 712) Cut CL 1 mm up to SRW 861 mm13) Cut CL 1 mm up to SRW 1461 mm14) Cut CL 1 mm up to SRW 2061 mm1 ) When using load transfer device cut CL 1 mm on SRH 11 1 mm16) When using load transfer device cut CL 1 mm on SRH 17 1 mm17) When using load transfer device cut CL 1 mm on SRH 23 1 mm
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 51
52 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Hardware overview
SRH / mm Lever position / mm Length / mm Material no.
430 – 450 225 – 265 400 233418451 – 520 266 – 300 400 233418521 – 620 301 – 350 400 233418
621 – 650 393 – 407 680 233419
651 – 800 408 – 482 680 233419
801 – 1200 482 – 682 980 233420
1201 – 1600 448 – 648 1380 290912
1601 – 2000 680 – 880 1780 296146
2001 – 2400 880 – 1080 2180 296147
2401 – 2600 1080 2180 296147
(C 200) 308267
Lifting mish. device possible Handle height Length / mm Material no.
155 – 225 430 259717
226 – 310 400 259718
226 – 310 400 259718
X 311 – 400 580 259719
X 311 – 400 580 259719
X 401 – 600 980 259720
X 601 – 800 1380 259721
X 801 – 1000 1780 259762
X 1001 – 1200 2180 259763
X 1200 2180 259763
(C 200) 308267
Lever-operated espagnolette, fixed lever-heightSRH / mm Lever position / mm Length / mm Material no.
430 – 480 195 490 233408
481 – 500 195 490 233408
501 – 600 195 490 233408
601 – 800 335 690 233409
801 – 1000 490 890 233410
1001 – 1200 335 1090 233411
1201 – 1400 335 1290 233412
1401 – 1600 335 1490 233413
1601 – 1800 335 1690 296145
1601 – 1800 335 1690 296145
1801 – 2000 640 1890 296074
2001 – 2200 640 2090 296075
2201 – 2400 640 2290 296076
2401 – 2600 640 2290 296076
(C 200) 308267
T&T espagnolette, fixed handle heightLifting mish. device possible Handle height Length / mm Material no.
120 370 284314
X 170 490 259830
X 170 490 259830
X 263 690 259831
X 413 890 259834
X 513 1090 259838
X 563 1290 259840
X 563 1490 259842
X 563 1690 259846
X 1000 1690 259847
X 1000 1890 259849
X 1000 2090 259851
X 1000 2290 259854
X 1000 2290 259855
(C 200) 308267
SRH / mm Lever position / mm Length / mm Material no.
370 – 620 No lever-operated espagnolettes possible in this range
621 – 800 236 – 325 680 242726
801 – 900 325 – 375 680 242726
901 – 1200 298 – 448 980 242728
1201 – 1600 448 – 658 1380 290912
1601 – 2000 680 – 880 1780 296146
2001 – 2400 880 – 1080 2180 296147
2401 – 2600 1080 2180 296147
(C 200) 308267
Lifting mish. device possible Handle height Length / mm Material no.
311 – 400 580 259766
401 – 450 980 623646
X 451 – 600 980 623646
X 601 – 800 1380 259768
X 801 – 1000 1780 259769
X 1001 – 1200 2180 259770
X 1200 2180 259770
(C 200) 308267
Lever-operated espagnolette, fixed lever-heightSRH / mm Lever position / mm Length / mm Material no.
430 – 510 233 490 317047
511 – 600 233 490 317047
601 – 800 195 690 242730
801 – 1000 490 890 242732
1001 – 1200 335 1090 233411
1201 – 1400 335 1290 233412
1401 – 1600 335 1490 233413
1601 – 1800 335 1690 296145
1601 – 1800 335 1690 296145
1801 – 2000 640 1890 296074
2001 – 2200 640 2090 296075
2201 – 2400 640 2290 296076
2401 – 2600 640 2290 296076
(C 200) 308267
T&T espagnolette, fixed handle heightLifting mish. device possible Handle height Length / mm Material no.
170 490 259856
170 490 259856
X 263 690 259858
X 413 890 259861
X 513 1090 259865
X 563 1290 259867
X 563 1490 259869
X 563 1690 259873
X 1000 1690 259874
X 1000 1890 259876
X 1000 2090 259878
X 1000 2290 259881
X 1000 2290 259881
(C 200) 308267
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 53
Hardware overview
1) With special corner drive2) With integrated T&T corner drive with P cam3) Screwing position under the lever.
Lever-operated espagnolette, fixed lever-heightSRH / mm Length / mm Lever position / mm Material no.
431 – 480 490 195 623365 1)
481 – 500 490 195 623365 1)
501 – 600 490 195 623365601 – 800 690 335 623369801 – 1000 890 490 623371
1001 – 1200 1090 335 6233721201 – 1400 1290 335 6233731401 – 1600 1490 335 6233741601 – 1800 1690 335 6233751601 – 1800 1690 335 6233751801 – 2000 1890 640 6233762001 – 2200 2090 640 6233772201 – 2400 2290 640 6233782401 – 2600 2290 640 623378
(C 200) 450822
Lifting mish. device possible Length / mm Handle height Material no.
370 120 284314 2)
X 490 170 259830X 490 170 259830X 690 263 259833X 890 413 259836X 1090 513 259838X 1290 563 259840X 1490 563 259843X 1690 563 259846X 1690 1000 259847X 1890 1000 259849X 2090 1000 259852X 2290 1000 259855X 2290 1000 259855
(C 200) 450821
Lifting mish. device possible Length / mm Handle height Material no.
430 155 – 225 259717 1)
400 226 – 310 259718
400 226 – 310 259718
X 580 311 – 400 259719
X 580 311 – 400 259719
X 980 401 – 600 259720
X 1380 601 – 800 259721
X 1780 801 – 1000 259762
X 2180 1001 – 1200 259763
X 2180 1001 – 1200 259763
(C 200) 308267
SRH / mm Length / mm Lever position / mm Material no.
370 – 450 400 225 – 265 623379 1)3)
451 – 520 400 266 – 300 623379 1)3)
521 – 620 400 301 – 350 623379 3)
621 – 650 680 393 – 407 623380 1)
651 – 800 680 408 – 482 623380
801 – 1200 980 482 – 682 623382
1201 – 1600 1380 448 – 648 623384
1601 – 2000 1780 680 – 880 623385
2001 – 2400 2180 880 – 1080 623386
2401 – 2600 2180 1080 – 1280 623386
(C 200) 308267
Lifting mish. device possible Length / mm Handle height Material no.
490 170 259856 2)
490 170 259856 2)
690 263 259860X 890 413 259863X 1090 513 259865X 1290 563 259867X 1490 563 259870X 1690 563 259873X 1690 1000 259874X 1890 1000 259876X 2090 1000 259879X 2290 1000 259882X 2290 1000 259882
(C 200) 450821
SRH / mm Length / mm Lever position / mm Material no.
431 – 510 490 233 623366 1)
511 – 600 490 233 623366601 – 800 690 195 623367 3)
801 – 1000 890 490 623370 3)
1001 – 1200 1090 335 6233721201 – 1400 1290 335 6233731401 – 1600 1490 335 6233741601 – 1800 1690 335 6233751601 – 1800 1690 335 6233751801 – 2000 1890 640 6233762001 – 2200 2090 640 6233772201 – 2400 2290 640 6233782401 – 2600 2290 640 623378
(C 200) 450822
Lifting mish. device possible Length / mm Handle height Material no.
580 311 – 400 259766980 401 – 450 623646
X 980 451 – 600 623646X 1380 601 – 800 259768X 1780 801 – 1000 259769X 2180 1001 – 1200 259770X 2180 1001 – 1200 259770
(C 200) 308267
SRH / mm Length / mm Lever position / mm Material no.
621 – 800 680 236 – 325 623381 1)3)
801 – 900 680 325 – 375 623381 3)
901 – 1200 980 298 – 448 623383 3)
1201 – 1600 1380 448 – 658 6233841601 – 2000 1780 680 – 880 6233852001 – 2400 2180 880 – 1080 6233862401 – 2600 2180 1080 – 1280 623386
(C 200) 308267
54 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Hardware overview Profile-related components
System HA Striker Tilt striker, zinc
Tilt striker, steel
TF tilt striker SEC striker, zinc
SEC striker, steel
mm Material no. Material no. Material no. Material no. Material no. Material no.
Euro rebate 24 mm 13.0 L 261943 632132 261935
13.0 R 262927 632133 262930
13.0 R 261933
Euro rebate 24 mm, with supporting-pins
13.0 L 261944 632132 261936
13.0 R 262929 632133 262931
13.0 R 261934
Euro groove 11 8, rebate depth 24 mm
13.0 L 378464 456956 378465
13.0 R 378457 456955 378466
13.0 R 378467
Euro rebate 30 mm 13.0 L 631525 602788
13.0 R 631526 602789
13.0 R 599651 602201 631527 602215
Euro rebate 30 mm, with supporting-pins
13.0 L 631502 602788
13.0 R 631504 602789
13.0 R 599652 602202 355611 602216
To be routed in, 25 mm rebate depth, 5 mm clearance
13.0 L 627988 627984 627988
13.0 R 627990 627986 627990
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 55
Hardware overview Profile-related components
System HA Bullet catch Lift. mish. device Night-vent Turn-restrictor Centre-closer, concealed
frame component frame component frame component frame component sash component frame componentmm Material no. Material no. Material no. Material no. Material no. Material no.
24 mm Euro rebate 13.0 L 261945 491798
13.0 R 262932 491798
13.0 R 261941 261947 450984 606610
Euro rebate 24 mm with supporting-pins
13.0 L 261946 337754
13.0 R 262933 337754
13.0 R 261942 261948 450984 617516
Euro groove 11 8, 24 mm rebate depth
13.0 R 378469 383281 256584
Euro rebate 30 mm 13.0 R 578785 595679 491798 450984 606612
Euro rebate 30 mm, with supporting-pins
13.0 R 578786 337754 450984 606613
To be routed in, 25 mm rebate depth, 5 mm clearance
13.0 L 551744
13.0 R 551743
56 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Profile Pivot rest Sash stay 250 Sash stay 350 Sash stay 500TF sash stay 250
TF sash stay 350
TF sash stay 500
Rebate hinge
Material no. Material no. Material no. Material no. Material no. Material no. Material no. Material no.
DIN R DIN L DIN R DIN L DIN R DIN L DIN R DIN L DIN R DIN L DIN R DIN L DIN R DIN L DIN R DIN L
Euro-rebate
563736 563737 563728 563732 563729 563733 563730 563734 600801 600800 600803 600802 600805 600804 563731 563735
Euro-rebate
570079 570080 570050 570054 570051 570075 570052 570076 – – – – – – 570053 570077
Hardware overview Profile-related components
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 57
Backset
Han
dle
heig
ht
dim
ensi
on H
H
10 mm, 33 mm deep
10 mm, 33 mm deep
18
43
Ø 25
15 Carry out the drillings for the window handle’s
sprocket and lugs.
Ø 10Ø 10
Ø 12
Drilling for the sash
Backset15
Ø 25
At
an o
verla
p he
ight
of
16 m
m
MillingEspagnolette gear-casing
InstallationDrilling the sash drill-holes
58 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
InstallationDrilling the sash drill-holes
46
62
92.5
152.
5 167.
5
337.
5
352.
5
35.8
108
Drilling for corner hinge and load transfer device
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 59
InstallationInstall the handle
Hardware groove
Espagnolette gear-casing
Threaded bevels
Screw fix the window handle in the main lock casing
with IN 965 5 x countersunk screws.
ugs, 10 mm
Spindle, 7 mm
52
Roto Swing window handlewith lugs and 7 mm spindle
60 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
32
24
56
11.5
17
2x Ø6
min
.10
3555
11.517
19.5
56
88
10
2x Ø6
11.5
17
32.5
24.5 47
.5
56.5
55
56
88
19.517
11.5 35
Reb
ate
de
pth
24 m
m
max
. R2
Rebate depth 24 mm
max. R2
depth
Rebate depth 24 mm
With load transfer device only for 80 kg sash weights
32
24
56
11.5
17
2x Ø6
min
.10
3555
11.517
19.5
56
8810
2x Ø6
11.5
17
32.5
24.5 47
.5
56.5
55
56
88
19.517
11.5 35
Reb
ate
de
pth
24 m
m
min
.
max
. R2
max. R2
InstallationDrilling the frame drill-holes
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 61
11.5
22.5
2x Ø6
min
. 10
3555
56
88
19.5
22.5
11.5
32
24
56
min
. 10
2 x Ø6
11.5
22.5
56
88
3555
19.5
11.5
22.5
17
32.5
24.5 47
.5
56.5
Reb
ate
de
pth
30 m
m
max
. R2
Rebate depth 30 mm
max. R2
depth
11.5
22.5
2x Ø6
min
. 10
3555
56
88
19.5
22.5
11.5
32
24
56
min
. 10
2 x Ø6
11.5
22.5
56
88
3555
19.5
11.5
22.5
17
32.5
24.5 47
.5
56.5
With load transfer device only for 80 kg sash weights
Rebate depth 30 mm
Reb
ate
de
pth
30 m
m
max
. R2
max. R2
InstallationDrilling the frame drill-holes
62 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
InstallationCropping the hardware components
Crop with pneumatic cropper (punched hole)Hole punchDescription Material no.
neumatic cropper S 100 (not dep.) DIN L 553992
DIN R 553993
Cropper with tool DIN L 262153
DIN R 262156
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 63
InstallationInstalling sash hardware components
1. Corner drive2. Corner drive, 3. espagnolette4. Stay corner drive5. Stay guide6. Centre lock, vertical and horizontal7. Corner hinge
7.
6.
6.
5.4.
3.
2.
1.
64 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
InstallationInstalling the turn-restrictor
32
95
104
Pivot restTurn-restrictor, frame component
Positioning of the turn-restrictor 90°
151
162.5
Turn-restrictor, sash component
Corner hinge
151
162.5
NOTE!The turn-restrictor is a
comfort component, not
a security component.
WARNING! The 90° embossing must
point towards the corner
hinge. Incorrect installation
of the turn-restrictor’s sash
component destroys the
pivot rest
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 65
32
95
104
Pivot restTurn-restrictor, frame component
Positioning of the turn-restrictor 90°
151
162.5
Turn-restrictor, sash component
Corner hinge
151
162.5
NOTE!The turn-restrictor is a
comfort component, not
a security component.
WARNING! The 90° embossing must
point towards the corner
hinge. Incorrect installation
of the turn-restrictor’s sash
component destroys the
pivot rest
Press the hole at the end of the sash component on the
rubber ring of the frame component’s bolt.
InstallationInstalling the turn-restrictor
66 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
417
200
Additional scissor stay Frame component
Additional scissor stay Sash component
Stay guide
Corner drive
CAUTION! If the additional scissor stay TF is used, a lifting mishandling device must be installed.
If the additional scissor stay TF is installed, the arrestable brake-stay and the multi-stepped night-vent cannot
be used.
Observe the installation dimensions for frame and sash component
InstallationInstalling an additional scissor stay
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 67
68 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
InstallationConnecting sash and frameSash stay 250, 350 and 500
Hinging the sash
1. Put the pivot rest into its original position
( closed sash position).2. Bring the handle into the turn mode.3. Run down the sash slightly tilted along the frame,
until the corner hinge meets the pivot rest.
4. Secure the sash from falling out.5. Press down the lifting mishandling device
(if mounted).6. Bring the handle into the tilt mode.
This is a conscious – and in this case necessary – hard-
ware mishandling operation!
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 69
InstallationConnecting sash and frameSash stay 250, 350 and 500
Tilt-depth regulator, tilt depth 140 mm (standard)
Entry tilt mode
7. Press down the stay arm on the stay guide and
supporting arm.
Retainer-clasp 8. Close the retainer-clasp.9. Operate again the lifting mishandling device and bring
the handle into the turn mode.
NOTE!se the anti slam device (487206) for 80 mm
tilt depth.
ilt depth 140 mm (standard)
Slider
180°
ilt depth 80 mm
Slider
7. Adjust the desired tilt depth
(Standard tilt depth 140 mm)
180°
ilt depth 140 mm (standard)
180°
ilt depth 80 mm 8. Connect the slider of the sash stay with the stay
guide.
Slider s nal position = anti-slam device
Slider s nal position = anti-slam device
Hitching pin
Hitching pin
ilt depth 140 mm (standard)
ilt depth 80 mm
9 Lift the sash stay arm and let the drilling-hole of
the sash stay arm snap on the hitching pin of the
supporting arm.10. Operate again the lifting mishandling device and bring
the handle into the turn mode.
NOTE!he slider s final position ( anti slam device) is
reached automatically by means of tilting the
sash.
70 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
InstallationInstalling the load transfer deviceGeneral advice
FunctionalityThe spring in the load transfer device disburdens the pivot rest permanently
by approx. 60 to 80 kg.
In order to do so, the spring must be pre-stretched to a certain length. This
applies regardless of the adjustment height of the sash.
The relieving of the pivot rest is carried out over the entire lifespan of the
hardware, also in consideration of sagging and wear and tear.
Installation adviceThe load transfer device’s spring can already be pre-stretched in the work-
shop, this however only makes sense if the sash is installed with the full glass
load.
Transport possibility 1Transport the sash and frame separately.
Transport possibility 2Transport the sash in the frame.
CAUTION! he bearing can buckle
Pre-stretch the load transfer device’s spring and support the frame
with spacers in the bottom rebate
UnhingingScrew out the screw of the load transfer device until the spring tension is re-
leased completely (support rod is loosened). If the tension in the spring is not
completely released, the sash cannot be hinged into the frame again.
Application restrictionso not e uip sashes with a sash weight < 80 kg with a load transfer device,
because this can result in malfunctions.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 71
InstallationInstalling the load transfer device
2.
1.
3.
5.
6.
Functionality of the load transfer device
The spring in the load transfer device disburdens the
pivot rest permanently by approx. 60 to 80 kg.
In order to do so, the spring must be pre-stretched to
a certain length. This applies regardless of the adjust-
ment height of the sash.
The relieving of the pivot rest is carried out over the
entire lifespan of the hardware, also in consideration of
sagging and wear and tear.
NOTE!Do not equip sashes with a sash weight
< 80 kg with a load transfer device, because
this can result in malfunctions.
It is compulsory to use a turn-restrictor.
If the sash is already hinged in the frame prior
to transportation, the spring of the load trans-
fer can be clamped in the workshop. How-
ever, this is only sensible if the sash is assem-
bled with the full glass load.
Installing the load transfer device
1. Insert the load transfer device’s sash component
up against the corner hinge and screw fix.2. Loosen the pivot rest’s top screw connection.3. Place the load transfer device’s frame component
on top of the pivot rest and screw fix.4. Hinge the sash (see page 68).5. Connect the support rod with the sash component
and insert into the cavity of the frame component.
Adjusting the load transfer device
6. d ust the load transfer device with a 4 mm hex key
in a (90 ) opened sash position
Adjust the adjusting screw in the silver divided cir-
cle in such a manner that the sum of the red and
silver divided circles result in one complete circle.
Check the result in the inspection opening.
6.
72 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 73
Installation guidelineBurglar-resistant windows in accordance with DIN EN 1627–
1630 may only be named so, if the installation has been carried
out in all points in accordance with the specified standards.
Attach spacer blocks in the vicin-
ity of the screw fixings of the se-
curity strikers and the concealed
centre-closers.
Frame
Masonry brickwork
Spacer blocks
InstallationFixing suggestion installation of security windows
74 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Installation drawingsPositioning of the frame components ilt urn and ilt irst – asic security
T&T espagnolette, fixed handle height Basic security
L Lifting mishandling device C ullet catch
76
58
50
149
12
95
58
T&T espagnolette, backset 15SRH / mm HH G1 G2 G3 LMD C
280 – 480 120 – – – – –
481 – 600 170 – – – 223 –
601 – 800 263 – – – 138 –
801 – 1000 413 – – – 288 –
1001 – 1200 513 700 – – 388 –
1201 – 1400 563 700 – – 388 –
1401 – 1600 563 700 – – 388 –
1601 – 1800 563 700 1370 – 388 –
1601 – 1800 1000 700 1370 – 1121 1244
1801 – 2000 1000 700 1370 – 1121 1244
2001 – 2200 1000 700 1370 – 1121 1244
2201 – 2400 1000 700 1370 – 1121 1244
2401 – 2600 1000 700 1370 1770 1121 1244
Stay guideSRW / mm A Size
801 – 1000 600 500 / 890
1001 – 1200 750 500 / 1090
1201 – 1400 750 500 / 1090
Centre lock, vertical, without load transferSRH / mm CL1 CL2 CL3
1101 – 1800 746 – – C 600 E
1801 – 2400 746 1346 – CL 600 E CON + CL 600 E
2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E
Centre lock, vertical, with load transfer SRH / mm CL1 CL2 CL3
1101 – 1150 550 – – – C 400 E
1151 – 1800 746 – – C 600 E
1801 – 2400 746 1346 – CL 600 E CON + CL 600 E
2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E
Centre lock, horizontalSRW / mm CLH1
1101 – 1400 658 CL 600 E
CLH1
Tilt striker
LMD
G3
G2
G1
HH
CL2
CL1
Turn-restrictor
p to SRW 430
rom SRW 431
BC
CL3
A
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 75
SRH / mm A B C D E LMD C
310 – 450 – – – – – – –
451 – 620 – – – – – –
621 – 800 125 – – – – 137 –
801 – 1200 125 – – – – 137 –
1201 – 1600 125 340 – – – 137 –
1601 – 2000 – 312 358 – – 109 232
2001 – 2400 – 312 358 758 740 109 232
2401 – 2600 – 312 358 758 740 109 232
76
58
50
BE
AC
D
Basic security
Tilt striker
BC
LMD
1)LMD
2)
Handle/centre
L Lifting mishandling device C ullet catch
Installation drawingsPositioning of the frame components ilt urn and ilt irst – asic security
76 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Installation drawingsPositioning of the frame componentsilt urn – RC1 N
T&T espagnolette, fixed handle height
L Lifting mishandling device C ullet catch
58
12
149
86.576
95CLH1
Tilt striker
BC
LMD
G2
G1
HH
CL2
CL1
CLH2
A
Turn-restrictor
CL3
T&T espagnolette, backset 15SRH / mm HH G1 G2 G3 LMD C
280 – 480 120 – – – – –
481 – 600 170 – – – 223 –
601 – 800 263 – – – 138 –
801 – 1000 413 – – – 288 –
1001 – 1200 513 700 – – 388 –
1201 – 1400 563 700 – – 388 –
1401 – 1600 563 700 – – 388 –
1601 – 1800 563 700 1370 – 388 –
1601 – 1800 1000 700 1370 – 1121 1244
1801 – 2000 1000 700 1370 – 1121 1244
2001 – 2200 1000 700 1370 – 1121 1244
2201 – 2400 1000 700 1370 – 1121 1244
2401 – 2600 1000 700 1370 1770 1121 1244
Stay guideSRW / mm A Size
801 – 1000 600 500 / 890
1001 – 1200 750 500 / 1090
1201 – 1400 750 500 / 1090
Centre lock, vertical, without load transferSRH / mm CL1 CL2 CL3
1101 – 1800 746 – – C 600 E
1801 – 2400 746 1346 – CL 600 E CON + CL 600 E
2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E
Centre lock, vertical, with load transferSRH / mm CL1 CL2 CL3
1101 – 1150 550 – – C 400 E
1151 – 1800 746 – – C 600 E
1801 – 2400 746 1346 – CL 600 E CON + CL 600 E
2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E
Centre lock, horizontal, without turn-restrictorSRW / mm CLH1 CLH2
450 – 650 258 – CL 200 P
651 – 850 462 – CL 400 P
851 – 1000 658 – CL 600 P
Centre lock, horizontal, with turn-restrictorSRW / mm CLH1 CLH2
650 – 850 258 – CL 200 P
851 – 1050 462 – CL 400 P
1051 – 1250 658 – CL 600 P
1251 – 1400 658 858 CL 600 E CON + CL 200 P
G3
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 77
L Lifting mishandling device C ullet catch
Installation drawingsPositioning of the frame componentsilt urn – RC1 N
SRH / mm A B C D E LMD C
310 – 450 – – – – – – –
451 – 620 – – – – – – –
621 – 800 125 – – – – 137 –
801 – 1200 125 – – – – 137 –
1201 – 1600 125 340 – – – 137 –
1601 – 2000 – 312 358 – – 109 232
2001 – 2400 – 312 358 758 740 109 232
2401 – 2600 – 318 358 758 740 109 232
58
86.576
BE
AC
D
Tilt striker
BC
LMD
1)LMD
2)
Handle/centre
78 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Installation drawingsPositioning of the frame componentsilt urn – RC2 RC2 N
T&T espagnolette, fixed handle height
L Lifting mishandling device C ullet catch
58
86.5
149
76
12
95
CLH1
Tilt striker
BC
LMD
G4
G3
G2
HH
CL2
CL1
CLH2
G1
CL4
CL3
A
Turn-restrictor
T&T espagnolette, backset 15SRH / mm HH G1 G2 G3 G4 LMD C
490 – 600 170 – – – – 223 –
601 – 800 263 – 383 – – 138 –
801 – 1000 413 160 550 – – 288 –
1001 – 1200 513 160 700 – – 388 –
1201 – 1400 563 160 700 – – 388 –
1401 – 1600 563 160 700 1170 – 388 –
1601 – 1800 563 160 700 1370 – 388 –
1601 – 1800 1000 160 700 1370 – 1121 1244
1801 – 2000 1000 160 700 1370 – 1121 1244
2001 – 2200 1000 160 700 1370 1770 1121 1244
2201 – 2400 1000 160 700 1370 1770 1121 1244
Stay guideSRW / mm A Size
801 – 1000 600 500 / 890
1001 – 1200 600 500 / 1090
1201 – 1400 600 500 / 1090
Centre lock, horizontal, without turn-restrictorSRW / mm CLH1 CLH2
450 – 650 258 – C 200
651 – 850 462 – C 400
851 – 1000 658 – C 600
Centre lock, horizontal, with turn-restrictorSRW / mm CLH1 CLH2
650 – 850 258 – C 200
851 – 1050 462 – C 400
1051 – 1250 658 – C 600
1251 – 1400 658 858 C 600 CON C 200
Centre lock, vertical, without load transferSRH / mm CL1 CL2 CL3 CL4
490 – 650 346 – – – C 200
651 – 850 550 – – – C 400
851 – 1050 746 – – – C 600
1051 – 1250 746 946 – – C 600 CON C 200
1251 – 1450 746 1150 – – C 600 CON C 400
1451 – 1650 746 1346 – – C 600 CON C 600
1651 – 1850 746 1346 1546 – 2x C 600 CON C 200
1851 – 2050 746 1346 1750 – 2x C 600 CON C 400
2050 – 2250 746 1346 1946 – 2x C 600 CON C 600
2251 – 2400 746 1346 1946 2146 3x C 600 CON C 200
Centre lock, vertical, with load transfer SRH / mm CL1 CL2 CL3
1000 – 1150 550 – – C 400
1151 – 1350 746 – – C 600
1351 – 1550 746 946 – C 600 CON C 200
1551 – 1750 746 1150 – C 600 CON C 400
1751 – 1950 746 1346 – C 600 CON C 600
1951 – 2150 746 1346 1546 2x C 600 CON C 200
2151 – 2350 746 1346 1750 2x C 600 CON C 400
2351 – 2400 746 1346 1946 2x C 600 CON C 600
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 79
58
BE
AC
D
76
Tilt striker
BC
LMD
1LMD
2
Handle/centre
L Lifting mishandling device C ullet catch
Installation drawingsPositioning of the frame componentsilt urn – RC2 RC2 N
SRH / mm A B C D E LMD 1 LMD 2 C
490 – 620 – – – – – – – –
621 – 800 125 – – – – 137 – –
801 – 1200 125 – – – – 137 – –
1201 – 1600 125 340 – – – 137 – –
1601 – 2000 – 312 358 – – – 109 232
2001 – 2400 – 312 358 758 740 – 109 232
80 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
L Lifting mishandling device C ullet catch
Installation drawingsPositioning of the frame componentsTurn-Only hardware – Basic security
T&T espagnolette, fixed handle height Basic security
76 50
58
50
50
12
95CLH1
Cen
tre-
clos
ers,
con
ceal
ed
BC
LMD
G4
G3
G2
CL2
CL1
CLH1
Turn-restrictor
HH
CL3
T&T espagnolette, backset 15SRH / mm HH G1 G2 G3 G4 LMD C
280 – 480 120 – – – – – –
481 – 600 170 – – – – 223 –
601 – 800 263 – – – – 138 –
801 – 1000 413 – – – – 288 –
1001 – 1200 513 – 700 – – 388 –
1201 – 1400 563 – 700 – – 388 –
1401 – 1600 563 – 700 – – 388 –
1601 – 1800 563 – 700 1370 – 388 –
1601 – 1800 1000 – 700 1370 – 1121 1244
1801 – 2000 1000 – 700 1370 – 1121 1244
2001 – 2200 1000 – 700 1370 – 1121 1244
2201 – 2400 1000 – 700 1370 – 1121 1244
2401 – 2600 1000 – 700 1370 1770 1121 1244
Centre-closer, concealedSRH / mm CL1 CL2 CL3
1000 – 1200 550 – –
1201 – 1800 746 – –
1801 – 2400 746 1346 –
2401 – 2600 746 1346 1946
Centre lock, horizontal, topSRW / mm CLH1 Top
1101 – 1400 676 600 E
Centre lock, horizontal, bottomSRW / mm CLH1 Bottom
1101 – 1400 658 600 E
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 81
Installation drawingsPositioning of the frame componentsTurn-Only hardware – Basic security
Basic security
L Lifting mishandling device C ullet catch
76 50
58
BC
LMD
LMD
Handle/ centre
BC
AB
E
SRH / mm A B C D E LMD C
310 – 450 – – – – – – –
451 – 620 – – – – – –
621 – 800 125 – – – – 137 –
801 – 1200 125 – – – – 137 –
1201 – 1600 125 340 – – – 137 –
1601 – 2000 – 312 358 – – 109 232
2001 – 2400 – 312 358 758 740 109 232
2401 – 2600 – 312 358 758 740 109 232
82 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
5876
7658
Installation drawingsPositioning of the frame componentsTilt-Only hardware – Basic security
Basic security
CL1
CL1
Centre-closer, concealed
BA
SRW / mm A B
451 – 620 – –
621 – 800 125 –
801 – 1200 125 –
1201 – 1400 125 340
Centre lock, verticalSRH / mm CL1 Right
801 – 1200 480 – – 400 E
Centre lock, verticalSRH / mm CL1 Left
801 – 1200 462 – – 400 E
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 83
Installation drawingsPositioning of the frame componentsurn Only ilt urn – asic security
w/o centre post
T&T espagnolette, fixed handle height Basic security
12
70
52
A
52
149
52CLH1
Centre of clearance
CL2
CL1
CLH1
12 mm clearance between the sashes
CLH1
CL2
CL1
Cen
tre-
clos
ers,
con
ceal
ed
Tilt striker
CL3
CL3
Centre-closer, concealedSRH / mm CL1 CL2 CL3
1000 – 1200 550 – –
1201 – 1800 746 – –
1801 – 2400 746 1346 –
2401 – 2600 746 1346 1946
Centre lock, horizontal, topSRW / mm CLH1 Top
1100 – 1400 652 CL 600 E
Centre lock, horizontal, bottomSRW / mm CLH1 Bottom
1100 – 1400 652 CL 600 E
Centre lock, vertical, without load transferSRH / mm CL1 CL2 CL3
1101 – 1800 746 – – C 600 E
1801 – 2400 746 1346 – CL 600 E CON + CL 600 E
2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E
Centre lock, vertical, with load transfer SRH / mm CL1 CL2 CL3
1101 – 1150 550 – – C 400 E
1151 – 1800 746 – – C 600 E
1801 – 2400 746 1346 – CL 600 E CON + CL 600 E
2401 – 2600 746 1346 1750 2x C 600 E CON C 400 E
Centre lock, horizontalSRW / mm CLH1
1101 – 1400 652 CL 600 E
Stay guideSRW / mm A Size
801 – 1000 600 500 / 890
1001 – 1200 750 500 / 1090
1201 – 1400 750 500 / 1090
INSTALLATION ADVICEHinge in the passive sash with lever-operated
espagnolette in open position.
84 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Installation drawingsPositioning of the frame componentsurn Only ilt urn – RC1 N
T&T espagnolette, fixed handle height
Centre lock, vertical, without load transferSRH / mm CL1 CL2 CL3
1101 – 1800 728 – – C 600 E
2001 – 2400 728 1328 – CL 600 E CON + CL 600 E
2401 – 2600 728 1328 1732 2x CL 600 E CON + CL 400 E
Centre lock, vertical, with load transfer SRH / mm CL1 CL2 CL3
1101 – 1150 532 – – C 400 E
1151 – 1800 728 – – C 600 E
1801 – 2400 728 1328 – CL 600 E CON + CL 600 E
2401 – 2600 728 1328 1732 2x CL 600 E CON + CL 400 E
Centre lock, horizontal, without turn-restrictor, bottomSRW / mm CLH1
450 – 650 252 CL 200 P
651 – 850 456 CL 400 P
851 – 1000 652 CL 600 P
Centre lock, horizontal, with turn-restrictor, bottomSRW / mm CLH1 CLH2
650 – 850 252 – CL 200 P
851 – 1050 456 – CL 400 P
1051 – 1250 652 – CL 600 P
1251 – 1400 652 852 CL 600 E CON + CL 200 P
Centre lock, horizontal, topSRW / mm CLH1 CLH2
911 – 1110 452 – CL 400 E CON
1111 – 1310 652 – CL 600 E CON
1311 – 1400 652 – C 600 E CON C 200 CON
Centre lock, vertical, without load transfer SRH / mm CL1 CL2 CL3
1101 – 1800 746 – – C 600 E
1801 – 2400 746 1346 – CL 600 E CON + CL 600 E
2401 – 2600 746 1346 1750 2x CL 600 E CON + CL 400 E
Centre lock, vertical, with load transfer SRH / mm CL1 CL2 CL3
1101 – 1150 550 – – C 400 E
1151 – 1800 746 – – C 600 E
1801 – 2400 746 1346 – CL 600 E CON + CL 600 E
2401 – 2600 746 1346 1750 2x CL 600 E CON + CL 400 E
Centre lock, horizontal, without turn-restrictorSRW / mm CLH1
450 – 650 252 CL 200 P
651 – 850 456 CL 400 P
851 – 1000 652 CL 600 P
Centre lock, horizontal, with turn-restrictorSRW / mm CLH1 CLH2
650 – 850 252 – CL 200 P
851 – 1050 456 – CL 400 P
1051 – 1250 652 – CL 600 P
1251 – 1400 652 852 CL 600 E CON + CL 200 P
Stay guideSRW / mm A Size
801 – 1000 600 500 / 890
1001 – 1200 750 500 / 1090
1201 – 1400 750 500 / 1090
w/o centre post
52
52 70
52
12
149
131
9595
CLH1
Centre of clearance
CL2
C1
CLH1
12 mm clearance between the sashes
CLH1
CL2
CL1
Tilt striker
CL3
CL3
CLH2 CLH2
A
Turn-restrictorTurn-restrictor
INSTALLATION ADVICEHinge in the passive sash with lever-operated
espagnolette in open position.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 85
Installation drawingsPositioning of the frame componentsurn Only ilt urn – RC2 RC2 N
T&T espagnolette, fixed handle height
Centre lock, vertical, without load transferSRH / mm CL1 CL2 CL3 CL4
490 – 650 328 – – – C 200
651 – 850 532 – – – C 400
851 – 1050 728 – – – C 600
1051 – 1250 728 928 – – C 600 CON C 200
1251 – 1450 728 1132 – – C 600 CON C 400
1451 – 1650 728 1328 – – C 600 CON C 600
1651 – 1850 728 1328 1528 – 2x C 600 CON C 200
1851 – 2050 728 1328 1732 – 2x C 600 CON C 400
2051 – 2250 728 1328 1928 – 2x C 600 CON C 600
2251 – 2400 728 1328 1928 2128 3x C 600 CON C 200
Centre lock, vertical, with load transfer SRH / mm CL1 CL2 CL3
1000 – 1150 532 – – C 400
1151 – 1350 728 – – C 600
1351 – 1550 728 928 – C 600 CON C 200
1551 – 1750 728 1132 – C 600 CON C 400
1751 – 1950 728 1328 – C 600 CON C 600
1951 – 2150 728 1328 1528 2x C 600 CON C 200
2151 – 2350 728 1328 1732 2x C 600 CON C 400
2351 – 2400 728 1328 1928 2x C 600 CON C 600
Centre lock, horizontal, without turn-restrictorSRW / mm CLH1
450 – 650 252 C 200
651 – 850 456 C 400
851 – 1000 652 C 600
Centre lock, horizontal, with turn-restrictorSRW / mm CLH1 CLH2
650 – 850 252 – C 200
851 – 1050 456 – C 400
1051 – 1250 652 – C 600
1251 – 1400 652 852 C 600 CON C 200
Centre lock, horizontal, topSRW / mm CLH1 CLH2
711 – 910 252 – CL 200 CON
911 – 1110 452 – C 400 CON
1111 – 1310 652 – C 600 CON
1311 – 1400 652 852 C 600 CON C 200 CON
Centre lock, vertical, without load transferSRH / mm CL1 CL2 CL3 CL4
490 – 650 346 – – – C 200
651 – 850 550 – – – C 400
851 – 1050 746 – – – C 600
1051 – 1250 746 946 – – C 600 CON C 200
1251 – 1450 746 1150 – – C 600 CON C 400
1451 – 1650 746 1346 – – C 600 CON C 600
1651 – 1850 746 1346 1546 – 2x C 600 CON C 200
1851 – 2050 746 1346 1750 – 2x C 600 CON C 400
2051 – 2250 746 1346 1946 – 2x C 600 CON C 600
2251 – 2400 746 1346 1946 2146 3x C 600 CON C 200
Centre lock, vertical, with load transfer SRH / mm CL1 CL2 CL3
1000 – 1150 550 – – C 400
1151 – 1350 746 – – C 600
1351 – 1550 746 946 – C 600 CON C 200
1551 – 1750 746 1150 – C 600 CON C 400
1751 – 1950 746 1346 – C 600 CON C 600
1951 – 2150 746 1346 1546 2x C 600 CON C 200
2151 – 2350 746 1346 1750 2x C 600 CON C 400
2351 – 2400 746 1346 1946 2x C 600 CON C 600
Centre lock, horizontal, without turn-restrictorSRW / mm CLH1
450 – 650 252 C 200
651 – 850 456 C 400
851 – 1000 652 C 600
Centre lock, horizontal, with turn-restrictorSRW / mm CLH1 CLH2
650 – 850 252 – C 200
851 – 1050 456 – C 400
1051 – 1250 652 – C 600
1251 – 1400 652 852 C 600 CON C 200
Stay guideSRW / mm A Size
801 – 1000 600 500 / 890
1001 – 1200 600 500 / 1090
1201 – 1400 600 500 / 1090
52
52
149
131
12
7052
9595
CLH1CLH2
C2
C1
12 mm clearance between the sashes
CLH1
CL2
CL1
Tilt striker
CL3 C
3
CL4
A
CL4
CLH1
CLH2CLH2
Turn-restrictorTurn-restrictor
w/o centre post
86 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Top horizontal
Bottom horizontal
Esp
agno
lett
e si
de
Standard
RC1
Hin
ge
side
10
8
8
5
3 7 6
5
8
10
30
31
32
5 7 3 40
5 14
Installation drawings Jigs
espagnolette, fixed handle height ultipart centre lock, asic security RC1 N
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 87
Installation drawings Jigs
espagnolette, fixed handle height ultipart centre lock, asic security RC1 N
3 – 8 Single positioning jigs timber, T&T standardDescription Material no.
3
espagnolette side SRH 1601 – 2600 hinge side SRH 1801 – 2600
290050
5
bottom SRW 330 – 1100 hinge side SRH 280 – 1100 top hori ontal SRW 431 – 800
290072
6 Single positioning jig for lifting mishandling
espagnolette side SRH 481 – 800
290073
7 Single positioning jig espagnolette side SRH 801 – 1600 hinge side SRH 1101 – 1800
290074
8 Single positioning jig centre lock bottom hori ontal SRW 1101 – 1400 top hori ontal SRW 801 – 1400
290075
3 – 10 Single positioning jigs timber, TU-ON standardDescription Material no.
3
espagnolette side SRH 1601 – 2600 hinge side SRH 1801 – 2600
290050
5
bottom hinge side SRW SRH 315 – 1100 top hori ontal SRW 315 – 1200
290072
6 Single positioning jig for lifting mishandling
espagnolette side SRH 481 – 800
290073
7 Single positioning jig espagnolette side SRH 801 – 1600
290074
10
top bottom hori ontal 1101 – 1600290081
3 – 32 Single positioning jigs timber, T&T RC1Description Material no.
3
espagnolette side SRH 1601 – 2600 hinge side SRH 1801 – 2600
290050
5
top hori ontal SRW 450 – 800290072
6 Single positioning jig for lifting mishandling
espagnolette side SRH 481 – 800
290073
7 Single positioning jig espagnolette side SRH 801 – 1600 hinge side SRH 1101 – 1800
290074
8 Single positioning jig centre lock top hori ontal SRW 801 – 1400
290075
30 Positioning jig for centre lock bottom hori ontal SRW 450 – 800
SRW 1001 – 1050
268931
31 Positioning jig for centre lock bottom hori ontal SRW 851 – 1000
SRW 1051 – 1250
268932
32 Positioning jig for centre lock bottom hori ontal SRW 1251 – 1400
268933
40 Positioning jig hinge side SRH 280 – 2600
640450
14 602577
602597
88 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
AdjustmentExplanation on the adjustment chapter
Symbols for the sash adjustment when installedThese symbols facilitate the orientation while adjusting the window sashes
after installation with the following steps. se a 4 mm hex key as tool.
Height adjustment
Lateral adjustment
Gasket-compression adjustment
NOTE!Adjusting Roto hardware components may only be carried out by
authorised and qualified personnel.
NOTE!The stated values in the adjustment instructions chapter are
maximum values. hese must be adhered to.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 89
AdjustmentAdjustment instructionsSash stay
+2.0
–2.0
Lateral adjustment
+0.5
–0.5
Gasket-compression adjustment
90 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
+1.
5–
1.0
Height adjustment
After the height adjustment, the load transfer device has
to be read usted (refer to page 71).
+2.0
–1.5
Lateral adjustment
+0.5
–0.5
Gasket-compression adjustment
AdjustmentAdjustment instructions
ivot rest corner hinge
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 91
Adjustment Adjustment instructionsLocking cams
Locking cam adjustment instructions
Cam type Adjustment range Gasket-compression Height Side view Tools
E cam
90° 90°
–
P cam
90° 90°
–
V camCam type Adjustment range Gasket-compression
adjustment in mm Height adjustment in mm
Side view / top view Tools
90° 90°
– 0.8 mm – 0.2 mm
180° 180°
– – 0.4 mm
270° 270°
– 0.8 mm – 0.6 mm
360° 360°
– – 0.8 mm
0 = Original position
– 0.8 mm max. ad ustment
0.8 mm max. ad ustment
92 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
OperationOperating informationHandle positions of ilt urn hardware
The following symbols show the different handle positions and the resulting
sash positions of windows and balcony doors.
Handle position Sash position Symbol Meaning
Closed position of the sash.
Opened turn position of the sash.
Opened tilt position of the sash.
Malpositioning of the sash.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 93
OperationOperation information for end-usersHandle positions of ilt urn ilt irst hardware
The following symbols and signs can be used on windows and balcony doors
to protect the end-user.
lease order stickers separately (O R 14 E EN, O R 15 E EN).
geschlossenclosed
Drehkipp-BeschlagTilt&Turn hardware
öffnenopen
kippentilt
FehlschaltungenvermeidenAvoid mishandling mode!
08/2012 OPR_14_DE-EN_v1
geschlossenclosed
TiltFirst-BeschlagTiltFirst hardware
kippentilt
öffnenopen
FehlschaltungenvermeidenAvoid mishandling mode!
08/2012 OPR_15_DE-EN_v1
94 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Operation Troubleshooting
Troubleshooting
Problem Cause Corrective action Specialist company
End-users
Handle is difficult
to rotate.
– Frame parts are not properly
greased.
– Faulty handle.
– Handle screws are screwed in
too strong.
– Oblique screws in the sash
parts.
– Faulty sash parts.
– Incorrect strikers.
– Sash stay gasket compression
too strong (accumulation of
gaskets).
– Grease frame parts.
– Replace the handle.
– Slightly loosen the screws.
– Straight screw fixing of the
sash parts.
– Replace the sash parts.
– Replace strikers.
– Adjust or reduce the sash stay
gasket compression.
–
–
–
–
–
–
Handle can not ro-
tate 180°.
– Faulty hinging or installation
of sash parts.
– Faulty striker locations.
– Check adjustment in turn posi-
tion (if necessary, rehinge the
sash proceeding from
espagnolette).
– Adjust the striker locations.
–
–
In turn mode, the
sash falls into tilted
position.
– Too much clearance on top. – Check corner hinge location.
– Check pivot rest location.
– Raise the corner hinge.
( ttention tilt striker)
–
–
–
In tilt mode, the
sash falls into
turning position.
– Faulty tilting component. – Replace tilting component. –
Sash is rubbing in
tilt mode.
– Insufficient clearance on top. – Lower the corner hinge.
( ttention tilt striker )
–
Locking cams
rubber at striker.
– Faulty hinging of the sash.
– Faulty striker locations.
– Rehinge the sash.
– Adjust the striker locations.
–
–
= To be carried out only by a specialist company.
– = Not to be carried out by the end-user; the end-user may not carry out installation work! = To be carried out either by a specialist company or by the end-user
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 95
96 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
WARNING!Danger of injury through incorrectly conducted maintenance work!Incorrect maintenance can result in serious personal injury or material damage.– Before starting work, ensure that there is sufficient installation
room.
– Maintain order and cleanliness at the installation location.
– Ensure that the window or balcony door is prevented from
suddenly slamming during maintenance work.
– Get a specialist company to carry out adjustment work on hard-
ware – especially in the area of pivot rests or bogies and of
hinges – as well as replacement of parts and hinging, and
unhinging of sashes.
– Do not unhinge the sash for maintenance work.
At least annually, every six months for
Specialist company
End-users
If necessary, tighten fixing screws. –
Replace damaged screws. –
If necessary, replace components. –
Lubricate all moving components with acid free
and non resinous oil from a specialised dealer.
Lubricate steel strikers with acid free and non
resinous grease from a specialised dealer.
= To be carried out only by a specialist company.
– = Not to be carried out by the end-user; the end-user may not carry out installation work! = To be carried out either by a specialist company or by the end-user
NOTE!Observe the following environmental protection notes during
– Remove emerging or residual grease at the lubricating points
and dispose of in accordance with the valid local regulations.
– Collect exchanged oil in suitable containers and dispose of in
accordance with the environmental regulations.
The hardware overview shows the arrangement of the lubrication points. The
illustrated overview does not necessarily correspond to the installed hardware.
The number of lubrication points depends on the size and design of the win-
dow.
Maintenance Maintenance
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 97
Maintenance Lubrication points
Grease
Oil
98 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Inspection
t least annually, every six months for school and hotel buildings
Specialist company
End-users
Check that safety-relevant hardware compo-
nents are mounted securely.
Examine safety relevant hardware components
for wear and tear.
All movable parts are to be operation-tested.
All locking points are to be operation-tested.
The hardware’s smooth operation can be
checked by means of moving the window
handle:
– In accordance with IN 18055, the locking
and unlocking moment is max. 10 Nm.
– It can be checked using a torque wrench.
– The smooth operation can be improved by
greasing/oiling or adjusting the hardware.
–
–
– = To be carried out only by a specialist company.
– = Not to be carried out by the end-user; the end-user may not carry out installation work! = To be carried out either by a specialist company or by the end-user
Care
Specialist company
End-users
Keep the hardware free from deposits and
soiling.
Never use aggressive, acidic cleaners or
abrasive cleaning agents.
Only use mild, pH-neutral cleaning agents
in diluted form.
Only use a soft cloth for cleaning.
= To be carried out only by a specialist company.
– = Not to be carried out by the end-user; the end-user may not carry out installation work! = To be carried out either by a specialist company or by the end-user.
No legal claims can be derived from these recommendations, the application
is to be conveyed for each concrete individual case. The window and balcony
door manufacturer must draw builders and end-user’s particular attention to
these maintenance instructions. Roto Frank AG recommends window fabri-
cators to make maintenance agreements with their end-users.
Maintenance Inspection and care
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 99
Protection against corrosion
Specialist company
End-users
Aggressive vapours (e.g. by means of formic
acid or acetic acid, ammonia, amine or ammo-
nia compounds, aldehydes, phenols, chlorine,
tannic acid etc.) in the vicinity of the windows
must be absolutely avoided.
–
Never use acetic-acid or cross-linked acidic
sealing compounds or those with the above
mentioned contents, since both the direct con-
tact with the sealing compound and its vapori-
sation can attack the hardware’s surface.
–
Only electrogalvanised zinc plated and passi-
vated screws may be used for fixing the hard-
ware components.
–
o not use any stainless steel screws – = To be carried out only by a specialist company.
– = Not to be carried out by the end-user; the end-user may not carry out installation work! = To be carried out either by a specialist company or by the end-user.
Protection against dirt
Specialist company
End-users
Remove deposits and dirt from building mate-
rials (building dust, plaster, cement, etc.) or
similar materials with water before it cures.
Keep the hardware free from deposits and
soiling.
Never use aggressive, acidiferous cleaners or
abrasive cleaning agents.
Only use mild, pH-neutral cleaning agents in
diluted form.
Only use a soft cloth for cleaning. = To be carried out only by a specialist company.
– = Not to be carried out by the end-user; the end-user may not carry out installation work! = To be carried out either by a specialist company or by the end-user.
Maintenance Preservation of the surface finish
100 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
Specialist company
End-users
entilate the hardware and the rebate areas –
especially in the construction phase – so that
they are neither exposed to direct contact
with water nor to formation of condensation
water.
Ensure that (permanently) damp spatial air
cannot condense in the hinge and rebate
areas:
– Force ventilate several times each day
(open all windows for approx. 15 minutes).
– Also ventilate during holidays and ab-
sences.
– or more complex construction pro ects,
develop a ventilation plan if necessary.
If described systematic ventilation is not pos-
sible, e.g. because fresh screed must not be
traversed, or it cannot take draughts, put the
windows into the tilted position and make
them airtight by taping on the indoor side.
Divert the moisture present in the room air to
the outside by means of condensation dryers.
= To be carried out only by a specialist company.
– = Not to be carried out by the end-user; the end-user may not carry out installation work! = To be carried out either by a specialist company or by the end-user.
Protection against damages due to renovation work
Specialist company
End-users
When applying surface treatments of the win-
dows, exclude all hardware components from
this treatment, and thus protect against con-
tamination.
Use only adhesive tapes which do not dam-
age the varnish layers. In the case of doubt,
ask the window fabricator.
= To be carried out only by a specialist company.
– = Not to be carried out by the end-user; the end-user may not carry out installation work!
= To be carried out either by a specialist company or by the end-user.
Maintenance Preservation of the surface finish
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 101
DismantlingUnhinging the sash with load transfer device
Unhinge the load transfer device.
1. Bring the handle into the turn mode, open the
sash 90° and release the load transfer device.2. Press down the lifting mishandling device (if
mounted) and bring the handle into the tilt position.3. Unhinge the sash stay and secure the sash from
falling out.4. Press down the lifting mishandling device and bring
the handle into the turn mode.5. Turn the sash closed.6. Lift the sash slightly tilted out of the pivot rest.
NOTE!Screw out the screw of the load transfer
device until the spring tension is released
completely (support rod is loosened).
If the tension in the spring is not completely
released, the sash cannot be hinged into the
frame again.
102 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
DismantlingUnhinging the sash without load transfer deviceSash stay 350, 500 and sash stay 250
Unhinging the sash
1. Bring the handle into the turn mode (= open sash
position).2. Press down the lifting mishandling device (if
mounted) and bring the handle into the tilt position.3. Unhinge the sash stay and secure the sash from
falling out.
4. Press down the lifting mishandling device and bring
the handle into the turn mode.5. Turn the sash closed.6. Lift the sash slightly tilted out of the pivot rest.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 103
TransportTransport, packaging, storage
DANGER!Danger to life from incorrect handling and transport!Incorrect handling and unsuitable transport of window elements
can result in dangerous circumstances and cause severe accidents,
even including death.
Therefore:
– During loading and unloading, select force application points
which exclusively create reaction forces appropriate to the de-
signed layout of the hardware components for the intended in-
stallation location.
– During handling and transport, ensure that hardware is in the
locked position, so as to prevent an uncontrolled opening of the
sash. Use suitable means of securing for this.
– Use only transport protections designed for the respective clear-
ance.
– Wherever possible, transport the windows in the intended instal-
lation position. If transport in the intended installation position is
not possible, unhinge the sash, and transport it separately from
the frame to which it belongs.
uring transport, loading, and unloading, especially when auxiliaries such as
suckers, transport nets, forklifts, or cranes are used for support, reaction
forces may arise which result in damage or overloading to the installed hard-
ware. Therefore observe the following during all transport, loading, and un-
loading:
The type and the force application points when transporting, loading, and
unloading have a significant effect on the reaction forces which arise.
– Always choose the force application points so that the resulting reac-
tion forces are dissipated appropriate to the designed layout of the
hardware components for the intended installation location. This ap-
plies particularly for the hinge positions.
104 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
TransportTransport inspection
Check the delivery on receipt immediately for completeness and transport
damage.
NOTE!Claim any damage as soon as it is detected. Claims for damage can
only be invoked within the statutory reclamation period.
Subject to change. Roto NT Designo IMO_109_DE_v5_EN February 2017 105
Disposal
Separate the hardware components from the window and dispose of as
metal scrap.
106 February 2017 IMO_109_DE_v5_EN Roto NT Designo Subject to change.
C
ated
: an
uar
y 2
01
7
Su
bec
t to
ch
ang
e
O
_10
9_
N_v
© 2
01
7 R
oto
Fra
nk
AG
®
Ro
to is
a r
egis
tere
d t
rad
emar
k
Roto Frank AGWindow and Door Technology
Wilhelm-Frank-Platz 1
70771 Leinfelden-Echterdingen
Germany
Phone +49 711 7598 0
ax 49 711 7598 253
www.roto-frank.com
Roto Tilt&Turn | he ilt urn hardware system for windows and balcony doors
Roto Sliding | Hardware systems for large sliding windows and doors
Roto Door | Matching hardware technology “everything about doors”
Roto Equipment | Additional technology for windows and doors